XC9223/XC9224 Series
ETR0509_007
1A Driver Transistor Built-In Step-Down DC/DC Converters
☆GreenOperation-Compatible
■GENERAL DESCRIPTION
The XC9223/XC9224 series are synchronous step-down DC/DC converters with a 0.21Ω (TYP.) P-channel driver transistor and a
synchronous 0.23Ω (TYP.) N-channel switching transistor built-in. A highly efficient and stable current can be supplied up to 1.0A by
reducing ON resistance of the built-in transistor. With a high switching frequency of 1.0MHz or 2.0MHz, a small inductor is selectable;
therefore, the XC9223/XC9224 series are ideally suited to applications with height limitation such as HDD or space-saving
applications. Current limit value can be chosen either 1.2A (MIN.) when the LIM pin is high level, or 0.6A (MIN.) when the LIM pin is
low level for using the power supply which current limit value differs such as USB or AC adapter. With the MODE/SYNC pin, the
XC9223/XC9224 series provide mode selection of the fixed PWM control or automatically switching current limit PFM/PWM control.
As for preventing unwanted switching noise, the XC9223/XC9224 series can be synchronized with an external clock signal within the
range of ± 25% toward an internal clock signal via the MODE/SYNC pin. For protection against heat damage of the ICs, the
XC9223/XC9224 series build in three protection functions: integral latch protection, thermal shutdown, and short-circuit protection.
With the built-in U.V.L.O. (Under Voltage Lock Out) function, the internal P-channel driver transistor is forced OFF when input voltage
becomes 1.8V or lower. The XC9223B/XC9224B series’ detector function monitors the discretional voltage by external resistors.
■APPLICATIONS
●HDD
●Notebook computers
●CD-R / RW, DVD
●PDAs, Portable communication modems
●Digital cameras, Video recorders
●Various general-purpose power supplies
■FEATURES
Input Voltage Range
Output Voltage Range
Oscillation Frequency
Output Current
Maximum Current
Limit
Controls
Protection Circuits
Soft-Start Time
Voltage Detector
: 2.5V ~ 6.0V
: 0.9V ~ VIN (set by FB pin)
: 1MHz, 2MHz (+15% accuracy)
: 1.0A
: 0.6A (MIN.) ~ 0.9A (MAX)
with LIM pin=’L’
: 1.2A (MIN.) ~ 2.0A (MAX.)
with LIM pin=’H’
: PWM/PFM or PWM by MODE pin
: Thermal shutdown
Integral latch method
Short-circuit protection
: 1ms (TYP.) internally set
: B type (with VD function)
D type (without VD function)
: 0.21Ω
Built-in P-channel
MOSFET
Built-in Synchronous
: 0.23Ω
N-channel MOSFET
(No Schottky Barrier Diode Required)
High Efficiency
: 95% (VIN=5.0V, VOUT=3.3V)
Synchronized with an External Clock Signal
Ceramic Capacitor Compatible
Packages
: MSOP-10, USP-10B, SOP-8
* SOP-8 package is available for the XC9223D type only.
■TYPICAL APPLICATION CIRCUIT
■TYPICAL PERFORMANCE
CHARACTERISTICS
●Efficiency vs. Output Current
XC9223B081Ax
XC9223B081Ax
100
VIN=5V, FOSC=1MHz,
VIN=5V, FOSC=1M Hz, L =4.7uH(CDRH4D2 8C),
L=4.7μH (CDRH4D28C), CIN=10μF (ceramic), CL=10μF (ceramic)
CIN=10 uF(ceram i c), CL=1 0uF(cera m i c)
90
(*1) A capacitor of 2200pF～0.1μF is recommended to place at the CDD between the AGND
pin and the VIN pin.
Please refer to the page showing INSTRUCTION ON PATTERN LAYOUT for more detail.
Efficiency: EFFI (%)
80
70
VOUT=3.3V
60
50
VOUT=1.5V
40
30
20
PW M/PFM
PW M
10
0
1
10
100
Output Current: IOUT (mA)
1000
1/25
XC9223/XC9224 Series
■PIN CONFIGURATION
VIN 1
10 PGND
VDIN 2
9 LX
AGND 3
8 CE
VDOUT 4
VIN 1
8 PGND
AGND 2
7 LX
FB 3
6 CE
7 MODE/SYNC
FB 5
6 LIM
5 MODE/SYNC
LIM 4
MSOP-10
(TOP VIEW)
SOP-8
(TOP VIEW)
FB 5
6
LIM
VDOUT 4
7
MODE/SYNC
AGND 3
8
CE
VDIN 2
9
LX
VIN 1
10 PGND
USP-10B
(BOTTOM VIEW)
■PIN ASSIGNMENT
MSOP-10 *
1
2
3
4
5
6
7
8
9
10
PIN NUMBER
USP-10B *
1
2
3
4
5
6
7
8
9
10
SOP-8 **
1
2
3
4
5
6
7
8
PIN NAME
FUNCTION
VIN
VDIN
AGND
VDOUT
FB
LIM
MODE/SYNC
CE
Lx
PGND
Input
Voltage Detector Input
Analog Ground
VD Output
Output Voltage Monitor
Over Current Limit Setting
Mode Switch / External Clock Input
Chip Enable
Output of Internal Power Switch
Power Ground
* For MSOP-10 and USP-10B packages, please short the GND pins (pin #3 and 10)
** For SOP-8 package, please short the GND pins (pin# 2 and 8)
■FUNCTION CHART
1. CE Pin Function
CE PIN
OPERATIONAL STATE
H
L
ON
OFF *1
*1: Except for a voltage detector block in the XC9224 series.
2. MODE Pin Function
MODE PIN
FUNCTION
H
L
PWM Control
PWM/PFM Automatic Control
3. LIM Pin Function
2/25
LIM PIN
FUNCTION
H
L
Maximum Output Current: 1.0A
Maximum Output Current: 0.4A
XC9223/XC9224
Series
■PRODUCT CLASSIFICATION
●Selection Guide
●Ordering Information
XC9223①②③④⑤⑥ <The common CE pin in the DC/DC block and the voltage detector block.>
XC9224B②③④⑤⑥ <No CE pin in the voltage detector block. (Constant operating of the voltage detector block) >
DESIGNATOR
DESCRIPTION
SYMBOL
B
: With VD function
①
Transistor built-in,
Output voltage freely set (FB voltage),
Current Limit: 0.6A/1.2A
D
: Without VD function
0
8
: Fixed reference voltage
①=0, ②=8
1
: 1.0MHz
2
: 2.0MHz
A
: MSOP-10
D
: USP-10B
S
: SOP-8 (for the XC9223D type)
R
: Embossed tape, standard feed
L
: Embossed tape, reverse feed
②③
Reference Voltage
④
DC/DC Oscillation Frequency
⑤
⑥
Package
Device Orientation
DESCRIPTION
3/25
XC9223/XC9224 Series
■BLOCK DIAGRAM
●XC9223B/XC9224B Series
VIN
LIM
Error Amp.
FB
Current Limit
PFM
Comparator
PWM
Logic
Buffer
Driver
Current
Feedback
CE
LX
Vref with
Soft-Start,
CE
MODE/
SYNC
PGND
Ramp Wave
Generator,
OSC
PMW/PFM
Thermal
Shutdown
AGND
VD
VDOUT
VDIN
●XC9223D Series
VIN
LIM
Error Amp.
FB
Current Limit
PFM
Comparator
PWM
Logic
Buffer
Driver
Current
Feedback
CE
MODE/
SYNC
4/25
LX
Vref with
Soft-Start,
CE
PGND
PMW/PFM
Ramp Wave
Generator,
OSC
Thermal
Shutdown
AGND
XC9223/XC9224
Series
■ABSOLUTE MAXIMUM RATINGS
Ta=25OC
PARAMETER
SYMBOL
RATINGS
UNITS
VIN Pin Voltage
VDIN Pin Voltage
VDOUT Pin Voltage
VDOUT Pin Current
FB Pin Voltage
LIM Pin Voltage
MODE/SYNC Pin Voltage
CE Pin Voltage
Lx Pin Voltage
Lx Pin Current
VIN
VDIN
VDOUT
IDOUT
VFB
VLIM
- 0.3 ~ 6.5
- 0.3 ~ 6.5
- 0.3 ~ 6.5
10
- 0.3 ~ 6.5
- 0.3 ~ 6.5
- 0.3 ~ 6.5
- 0.3 ~ 6.5
- 0.3 ~ VDD + 0.3
2000
V
V
V
mA
V
V
V
V
V
mA
VMODE/SYNC
VCE
VLx
ILx
MSOP-10
Power Dissipation
USP-10B
SOP-8
350 (*1)
Pd
150
300
mW
Operating Temperature Range
Topr
- 40 ~ + 85
℃
Storage Temperature Range
Tstg
- 55 ~ +125
℃
*1: When implemented on a PCB.
5/25
XC9223/XC9224 Series
■ELECTRICAL CHARACTERISTICS
XC9223/XC9224 Series
PARAMETER
Topr=25℃
SYMBOL
CONDITIONS
MIN.
TYP.
MAX.
UNIT
CIRCUIT
Input Voltage
VIN
2.5
-
6.0
V
-
FB Voltage
VFB
0.784
0.800
0.816
V
①
Output Voltage Setting Range
VOUTSET
0.9
-
VIN
V
③
Maximum Output Current 1 (*1)
IOUTMAX1
0.4
-
-
A
③
Maximum Output Current 2 (*1)
IOUTMAX2
1.0
-
-
A
③
U.V.L.O. Voltage
VUVLO
1.55
1.80
2.00
V
①
Supply Current 1
IDD1
FB=VFB x 0.9, MODE/SYNC=0V
D1-1 (*2)
μA
②
Supply Current 2
IDD2
FB=VFB x 1.1 (Oscillation stops),
MODE/SYNC=0V
D1-2 (*2)
μA
②
Stand-by Current
ISTB
CE=0V
D1-6 (*2)
μA
②
D1-3 (*2)
MHz
③
D1-4 (*2)
MHz
④
FB=VFB x 0.9, VIN Voltage which Lx pin
voltage holding ‘L’ level (*8)
Connected to external components,
IOUT=10mA
Connected to external components,
IOUT=10mA, apply an external clock signal
to the MODE/SYNC
Oscillation Frequency
FOSC
External Clock Signal
Synchronized Frequency
SYNCOSC
External Clock Signal Cycle
SYNCDTY
Maximum Duty Cycle
MAXDTY
FB=VFB x 0.9
Minimum Duty Cycle
MINDTY
PFM Switch Current
IPFM
Efficiency (*3)
EFFI
Lx SW ‘H’ On Resistance (*4)
RLxH
FB=VFB x 1.1
Connected to external components,
MODE/SYNC=0V, IOUT=10mA
Connected to external components,
VIN=5.0V, VOUT=3.3V, IOUT=200mA
FB=VFB x 0.9, ILx=VIN-0.05V
Lx SW ‘L’ On Resistance
RLxL
Current Limit 1
ILIM1
Current Limit 2
25
-
75
%
④
100
-
-
%
①
-
-
0
%
①
-
200
250
mA
③
-
95
-
%
③
-
0.21
0.3 (*7)
Ω
①
-
0.23
0.3 (*7)
Ω
-
LIM=0V
0.6
-
0.9
A
①
ILIM2
LIM=VIN
1.2
-
2.0
A
①
Integral Latch Time (*5)
TLAT
FB=VFB x 0.9, Short Lx by 1Ω resistance
ms
①
Short Detect Voltage
VSHORT
Soft-Start Time
TSS
Thermal Shutdown Temperature
Hysteresis Width
D1-5 (*2)
FB Voltage which Lx becomes ‘L’ (*8)
0.3
0.4
0.5
V
①
CE=0V→VIN, IOUT=1mA
0.5
1.0
2.0
ms
①
TTSD
-
THYS
FB=VFB x 0.9, Voltage which Lx becomes
‘H’ after CE voltage changed from 0.4V to
1.2V (*8)
FB=VFB x 0.9, Voltage which Lx becomes
‘L’ after CE voltage changed from 1.2V to
0.4V (*8)
150
-
O
-
O
C
-
C
-
20
-
1.2
-
-
V
①
-
-
0.4
V
①
CE ‘H’ Voltage
VCEH
CE ‘L’ Voltage
VCEL
MODE/SYNC ‘H’ Voltage
VMODE/SYNCH
1.2
-
-
V
③
MODE/SYNC ‘L’ Voltage
VMODE/SYNCL
-
-
0.4
V
③
LIM ‘H’ Voltage
VLIMH
LIM ‘L’ Voltage
VLIML
IOUT=ILIM1 x 1.1, Check LIM voltage which
Lx oscillated after CE voltage changed
from 1.2V to 0.4V
CE ‘H’ Current
ICEH
VIN=CE=6.0V
CE ‘L’ Current
ICEL
VIN=6.0V, CE=0V
MODE/SYNC ‘H’ Current
IMODE/SYNCH
VIN=6.0V
MODE/SYNC ‘L’ Current
IMODE/SYNCL
VIN=6.0V, MODE/SYNC=0V
LIM ‘H’ Current
ILIMH
VIN=LIM=6.0V
LIM ‘L’ Current
ILIML
VIN=6.0V, LIM=0V
FB ‘H’ Current
IFBH
VIN=FB=6.0V
1.2
-
-
V
①
-
-
0.4
V
①
-
-
0.1
A
⑤
- 0.1
-
-
μA
⑤
-
-
0.1
μA
⑤
- 0.1
-
-
μA
⑤
-
-
0.1
μA
⑤
- 0.1
-
-
μA
⑤
-
-
0.1
μA
⑤
FB ‘L’ Current
IFBL
- 0.1
-
-
μA
⑤
Lx SW ‘H’ Leak Current
ILeakH
VIN=Lx=6.0V, CE=0V
-
-
1.0
μA
⑥
Lx SW ‘L’ Leak Current (*6)
ILeakL
VIN=6.0V, Lx=CE=0V
- 3.0
-
-
μA
⑥
6/25
VIN=6.0V, FB=0V
XC9223/XC9224
Series
■ELECTRICAL CHARACTERISTICS (Continued)
XC9223/XC9224 Series (Continued), Voltage Detector Block (*9)
PARAMETER
SYMBOL
Topr=25℃
CONDITIONS
VDIN Voltage which VDOUT becomes
‘H’ to ‘L’, Pull-up resistor 200kΩ
VDIN Voltage which VDOUT becomes
‘L’ to ‘H’, Pull-up resistor 200kΩ
MIN.
TYP.
MAX.
UNIT
CIRCUIT
0.676
0.712
0.744
V
⑦
0.716
0.752
0.784
V
⑦
-
5
-
%
-
Detect Voltage
VDF
Release Voltage
VDR
Hysteresis Width
VHYS
Output Current
IDOUT
VDIN=VDF x 0.9, apply 0.25V to VDOUT
2.5
4.0
-
mA
⑦
Delay Time
TDLY
Time until VDOUT becomes ‘L’ to ‘H’ after
VDIN changed from 0V to 1.0V
0.5
2.0
8.0
ms
⑦
VDIN ‘H’ Current
IVDINH
VIN=VDIN=6.0V
-
-
0.1
μA
⑤
VDIN ‘L’ Current
IVDINL
VIN=6.0V, VDIN=0V
- 0.1
-
-
μA
⑤
VDOUT ‘H’ Current
IVDOUTH
VIN=VDIN=VDOUT=6.0V
-
-
1.0
μA
⑤
VDOUT ‘L’ Current
IVDOUTL
VIN=VDIN=6.0V, VDOUT=0V
- 1.0
-
-
μA
⑤
VHYS=(VDR-VDF) / VDF x 100
Test Condition: Unless otherwise stated, VIN=3.6V, CE=VIN, MODE/SYNC=VIN
NOTE:
*1: When the difference between the input and the output is small, some cycles may be skipped completely before current maximizes.
If current is further pulled from this state, output voltage will decrease because of P-ch driver ON resistance.
*2: Refer to the chart below.
*3: EFFI = { ( output voltage x output current ) / ( input voltage x input current) } x 100
*4: On resistance (Ω)= (VIN- Lx pin measurement voltage) / 100mA
*5: Time until it short-circuits Lx with GND through 1Ω of resistance from a state of operation and is set to Lx=Low from current limit pulse
generating.
*6: When temperature is high, a current of approximately 100μA may leak.
*7: Designed value.
*8: Whether the Lx pin is high level or low level is judged at the condition of “H”>VIN-0.1V and “L”<0.05V.
*9: There is no voltage detector function available in the XC9223D series.
●Electrical Characteristics Standard Values
MIN.
1MHz
TYP.
MAX.
0.85
380
30
1.00
700
60
1.15
SYNCOSC
0.75
-
TLAT
-
6.0
No.
PARAMETER
SYMBOL
D1-1
D1-2
D1-3
IDD1
IDD2
FOSC
D1-5
Supply Current 1
Supply Current 2
Oscillation Frequency
External Clock
Synchronous Oscillation
Integral Latch Time
No.
PARAMETER
SYMBOL
D1-6
Stand-by Current
ISTB
D1-4
MIN.
2MHz
TYP.
MAX.
1.7
440
45
2.0
800
80
2.3
1.25
1.5
-
2.5
15.0
-
3.0
15.0
XC9223 SERIES
MIN.
TYP.
MAX.
-
0.1
2.0
XC9224 SERIES
MIN.
TYP.
MAX.
-
7.0
15.0
7/25
XC9223/XC9224 Series
■TYPICAL APPLICATION CIRCUIT
(*1) A capacitor of 2200pF～0.1μF is recommended to place at the CDD between the AGND pin and the VIN pin.
Please refer to the page showing INSTRUCTION ON PATTERN LAYOUT for more detail.
<Output Voltage Setting>
Output voltage can be set by adding external split resistors. Output voltage is determined by the following equation,
based on the values of RFB1 and RFB2. The sum of RFB1 and RFB2 should normally be 1MΩ or less.
VOUT = 0.8 x (RFB1 + RFB2) / RFB2
The value of CFB, speed-up capacitor for phase compensation, should be fzfb = 1 / (2 x π x CFB1 x RFB1) which is equal to
20kHz. Adjustments are required from 1kHz to 50kHz depending on the application, value of inductance (L), and value of
load capacity (CL).
[Example of calculation]
When RFB1=470kΩ, RFB2=150kΩ,
VOUT1 = 0.8 x (470k + 150k) / 150k =3.3V
[Typical example]
VOUT (V)
RFB1 (kΩ)
RFB2 (kΩ)
CFB (pF)
VOUT (V)
RFB1 (kΩ)
RFB2 (kΩ)
CFB (pF)
1.0
1.2
1.5
1.8
75
150
130
300
300
300
150
240
110
51
62
27
2.5
3.0
3.3
5.0
510
330
470
430
240
120
150
82
15
24
18
18
* When fzfb = 20kHz
[External components]
1MHz:
L: 4.7μH (CDRH4D28C, SUMIDA)
CL: 10μF (ceramic)
CIN: 10μF (ceramic)
2MHz:
L: 2.2μH (CDRH4D28, SUMIDA)
2.2μH (VLCF4020T-2R2N1R7, TDK)
CL: 10μF (ceramic)
CIN: 10μF (ceramic)
* As for CIN and CL, use output capacitors of 10μF or more.
(Ceramic capacitor compatible)
* High ESR (Equivalent Series Resistance) that comes by using a tantalum or an electrolytic capacitor causes high ripple voltage.
Furthermore, it can cause an unstable operation.
8/25
Use the IC after you fully confirm with an actual device.
XC9223/XC9224
Series
■OPERATIONAL EXPLANATION
Each unit of the XC9223/XC9224 series consists of a reference voltage source, a ramp wave circuit, error amplifier, PWM
comparator, phase compensation circuit, output voltage adjustment resistors, P-channel MOS driver transistor, N-channel
MOS synchronous rectification switching transistor, current limiter circuit, U.V.L.O. circuit and others. The series
compares, using the error amplifier, the internal reference voltage to the VOUT pin with the voltage feedback via resistors
RFB1 and RFB2. Phase compensation is performed on the resulting error amplifier output, to input a signal to the PWM
comparator to determine the turn-on time during PWM operation. The PWM comparator compares, in terms of voltage
level, the signal from the error amplifier with the ramp wave from the ramp wave circuit, and delivers the resulting output to
the buffer driver circuit to cause the Lx pin to output a switching duty cycle. This process is continuously performed to
ensure stable output voltage. The current feedback circuit monitors the P-channel MOS driver transistor current for each
switching operation, and modulates the error amplifier output signal to provide multiple feedback signals. This enables a
stable feedback loop even when a low ESR capacitor, such as a ceramic capacitor, is used, ensuring stable output voltage.
<Reference Voltage Source>
The reference voltage source provides the reference voltage to ensure stable output voltage of the DC/DC converter.
<Ramp Wave Circuit>
The ramp wave circuit determines switching frequency. The frequency is fixed internally and can be selected from 1.0MHz
and 2.0MHz. Clock pulses generated in this circuit are used to produce ramp waveforms needed for PWM operation, and
to synchronize all the internal circuits.
<Error Amplifier>
The error amplifier is designed to monitor output voltage. The amplifier compares the reference voltage with the feedback
voltage divided by the internal resistors (RFB1 and RFB2). When a voltage lower than the reference voltage is fed back, the
output voltage of the error amplifier increases. The gain and frequency characteristics of the error amplifier output are
fixed internally to deliver an optimized signal to the mixer.
<Current Limit>
The current limiter circuit of the XC9223/XC9224 series monitors the current flowing through the P-channel MOS driver
transistor connected to the Lx pin, and features a combination of the constant-current type current limit mode and the
operation suspension mode. For the current limit values, please select the values either from 1.2A (MIN.) when the LIM
pin is high level or 0.6A (MIN.) when the LIM pin is low level.
1When the driver current is greater than a specific level, the constant-current type current limit function operates to turn
off the pulses from the Lx pin at any given time.
2When the driver transistor is turned off, the limiter circuit is then released from the current limit detection state.
3At the next pulse, the driver transistor is turned on. However, the transistor is immediately turned off in the case of an
over current state.
4 When the over current state is eliminated, the IC resumes its normal operation.
The IC waits for the over current state to end by repeating the steps 1 through 3. If an over current state continues for
several msec and the above three steps are repeatedly performed, the IC performs the function of latching the OFF state of
the driver transistor, and goes into operation suspension mode. After being put into suspension mode, the IC can resume
operation by turning itself off once and then starting it up using the CE pin, or by restoring power to the VIN pin. Integral
latch time may be released from a current limit detection state because of the noise. Depending on the state of a substrate,
it may result in the case where the latch time may become longer or the operation may not be latched. Please locate an
input capacitor as close as possible.
ms
Limit < # mS
Limit > # ms
mS
Current Limit LEVEL
IOUT
0mA
VOUT
VSS
LX
CE
Restart
VIN
9/25
XC9223/XC9224 Series
■OPERATIONAL EXPLANATION (Continued)
<Thermal Shutdown>
For protection against heat damage of the ICs, thermal shutdown function monitors chip temperature. The thermal
shutdown circuit starts operating and the driver transistor will be turned off when the chip’s temperature reaches 150OC.
When the temperature drops to 130OC or less after shutting of the current flow, the IC performs the soft start function to
initiate output startup operation.
<Short-Circuit Protection>
The short-circuit protection circuit monitors FB voltage. In case where output is accidentally shorted to the Ground and
when the FB voltage decreases less than half of the FB voltage, the short-circuit protection operates to turn off and to
latch the driver transistor. In latch mode, the operation can be resumed by either turning the IC off and on via the CE pin,
or by restoring power supply to the VIN pin.
<Voltage Detector>
The detector block of the XC9223/9224 series detects a signal inputted from the VDIN pin by the VDOUT pin (N-ch
open-drain).
<U.V.L.O. Circuit>
When the VIN pin voltage becomes 1.8V (TYP.) or lower, the driver transistor is forced OFF to prevent false pulse output
caused by unstable operation of the internal circuitry. When the VIN pin voltage becomes 2.0V (TYP.) or higher, switching
operation takes place. By releasing the U.V.L.O. function, the IC performs the soft-start function to initiate output startup
operation. The U.V.L.O. function operates even when the VIN pin voltage falls below the U.V.L.O. operating voltage for
tens of ns.
<MODE/SYNC>
A MODE/SYNC pin has two functions, a MODE switch and an input of external clock signal. The MODE/SYNC pin
operates as the PWM mode when applying high level of direct current and the PFM/PWM automatic switching mode by
applying low level of direct current, which is the same function as the normal MODE pin. By applying the external clock
signal (±25% of the internal clock signal, ON duty 25% to 75%), the MODE/SYNC pin switches to the internal clock signal.
Also the circuit will synchronize with the falling edge of external clock signal. While synchronizing with the external clock
signal, the MODE/SYNC pin becomes the PWM mode automatically. If the MODE/SYNC pin holds high or low level of the
external clock signal for several μs, the MODE/SYNC pin stops synchronizing with the external clock and switches to the
internal clock operation. (Refer to the chart below.)
・External Clock Synchronization Function
VOUT
50mV/div
Lx
2V/div
Operates by the
internal clock
1MHz
Synchronous with the
external clock
1.2MHz
External Clock Signal
MODE/SYNC
2V/div
1.2MHz Duty50%
Delay time to the external clock synchronization
1.0μs/div
* When an input of MODE/SYNC is changed from “L” voltage into a clock signal of 1.2MHz and 50% duty.
10/25
XC9223/XC9224
Series
■OPERATIONAL EXPLANATION (Continued)
<PFM Switch Current>
In PFM control operation, until coil current reaches to a specified level (IPFM), the IC keeps the P-ch MOSFET on.
time that the P-ch MOSFET is kept on (TON) can be given by the following formula.
→IPFM①
TON= L×IPFM (VIN−VOUT)
In this case,
<Maximum IPFM Limit>
In PFM control operation, the maximum duty cycle (MAXPFM) is set to 50% (TYP.). Therefore, under the condition that the
duty increases (e.g. the condition that the step-down ratio is small), it’s possible for P-ch MOSFET to be turned off even when
coil current doesn’t reach to IPFM.
→IPFM②
IPFM②
IPFM①
Ton
FOSC
M axum um IPFM Current
Lx
Lx
I Lx
IPFM
0mA
I Lx
IPFM
0mA
11/25
XC9223/XC9224 Series
■NOTES ON USE
1. The XC9223/XC9224 series is designed for use with ceramic output capacitors. If, however, the potential difference
between dropout voltage, a ceramic capacitor may fail to absorb the resulting high switching energy and oscillation could
occur on the output. In this case, use a larger capacitor etc. to compensate for insufficient capacitance.
2. Spike noise and ripple voltage arise in a switching regulator as with a DC/DC converter. These are greatly influenced by
external component selection, such as the coil inductance, capacitance values, and board layout of external components.
Once the design has been completed, verification with actual components should be done.
3. In PWM control, very narrow pulses will be outputted, and there is the possibility that some cycles may be skipped
completely. This may happens while synchronizing with an external clock.
4. When the difference between VIN and VOUT is small, and the load current is heavy, very wide pulses will be outputted and
there is the possibility that some cycles may be skipped completely.
5. With the IC, the peak current of the coil is controlled by the current limit circuit. Since the peak current increases when
dropout voltage or load current is high, current limit starts operating, and this can lead to instability. When peak current
becomes high, please adjust the coil inductance value and fully check the circuit operation. In addition, please calculate
the peak current according to the following formula:
Ipk = (VIN - VOUT) x OnDuty / (2 x L x FOSC) + IDOUT
L: Coil Inductance Value
FOSC: Oscillation Frequency
6. When the peak current, which exceeds limit current, flows within the specified time, the built-in P-ch driver transistor is
turned off (an integral latch circuit). During the time until it detects limit current and before the built-in transistor can be
turned off, the current for limit current flows; therefore, care must be taken when selecting the rating for the coil.
7. The voltage drops because of ON resistance of a driver transistor or in-series resistance of a coil. For this, the current
limit may not be attained to the limit current value, when input voltage is low.
8. Malfunction may occur in the U.V.L.O. circuit because of the noise when pulling current at the minimum operation voltage.
9. This IC and the external components should be used within the stated absolute maximum ratings in order to prevent
damage to the device.
10. Depending on the state of the PC Board, latch time may become longer and latch operation may not work. The board
should be laid out so that capacitors are placed as close to the chip as possible.
11. In heavy load, the noise of DC/DC may influence and the delay time of the voltage detector may be prolonged.
12. Output voltage may become unstable when synchronizing high internal frequency with the external clock.
In such a case, please use a larger output capacitor etc. to compensate for insufficient capacitance.
13. When a voltage lower than minimum operating voltage is applied, the output voltage may fall before reaching the over
current limit.
14. When the IC is used in high temperature, output voltage may increase up to input voltage level at light load (less than 100
μA) because of the leak current of the driver transistor.
15. The current limit is set to LIM=H: 2000mA (MAX.). However, the current of 2000mA or more may flow. In case that the
current limit functions while the VOUT pin is shorted to the GND pin, when P-ch MOSFET is ON, the potential difference
for input voltage will occur at both ends of a coil. For this, the time rate of coil current becomes large. By contrast,
when N-ch MOSFET is ON, there is almost no potential difference at both ends of the coil since the VOUT pin is shorted to
the GND pin. Consequently, the time rate of coil current becomes quite small. According to the repetition of this
operation, and the delay time of the circuit, coil current will be converged on a certain current value, exceeding the
amount of current, which is supposed to be limited originally. The short protection does not operate during the soft-start
time. The short protection starts to operate and the circuit will be disabled after the soft-start time. Current larger than
over current limit may flow because of a delay time of the IC when step-down ratio is large. A coil should be used within
the stated absolute maximum rating in order to prevent damage to the device.
①Current flows into P-ch MOSFET to reach the current limit (ILIM).
②The current of ILIM (2000mA, MAX.) or more flows since the delay time of the circuit occurs during from the detection of
the current limit to OFF of P-ch MOSFET.
③Because of no potential difference at both ends of the coil, the time rate of coil current becomes quite small.
④Lx oscillates very narrow pulses by the current limit for several msec.
⑤The short protection operates, stopping its operation.
②
③
①
Delay
VLX
Overcurrent
Limit Value
ILX
（Coil Current）
12/25
④ #ms
⑤
XC9223/XC9224
Series
■INSTRUCTION ON PATTERN LAYOUT
1. In order to stabilize VIN’s voltage level, we recommend that a by-pass capacitor (CIN) be connected as close as
possible to the VIN & VSS pins.
2. Please mount each external component, especially CIN, as close to the IC as possible.
3. Wire external components as close to the IC as possible and use thick, short connecting traces to reduce the circuit
impedance.
4. Make sure that the PCB GND traces are as thick as possible, as variations in ground potential caused by high
ground currents at the time of switching may result in instability of the IC.
5. Unstable operation may occur at the heavy load because of a spike noise. 2200pF ~0.1μF of a capacitor, CDD, is
recommended to use between the AGND pin and the VIN pin for reducing noise.
・TOP VIEW
L
Inductor
0
Jumper Chip
R
Resistor
C
Ceramic Capaticor
・BOTTOM VIEW
13/25
XC9223/XC9224 Series
■TEST CIRCUITS
Circuit ②
Circuit ①
Waveform Measurement Point
1uF
A
ILx
LX
VIN
CE
MODE/
SYNC
ILIM
VIN
A
LX
CE
FB
1uF
V
MODE/
SYNC
ILIM
FB
VDOUT
VDIN
VDOUT
VDIN
AGND
PGND
AGND
PGND
Circuit ③
Waveform Measurement Point
L
VIN
A
CE
V
MODE/
SYNC
ILIM
CIN
VDOUT
V
AGND
IOUT
LX
A
RFB1
V
CFB
FB
RFB2
CL
VDIN
PGND
* External Components
L (1MHz) : 4.7μH (CDRH4D28C, SUMIDA)
L (2MHz) : 2.2μH (VLCF4020T-2R2N1R7, TDK)
CIN : 10μF (ceramic)
CL : 10μF (ceramic)
RFB1 : 130kΩ
RFB2 : 150kΩ
CFB : 62pF (ceramic)
Circuit ④
Waveform Measurement Point
VIN
CE
MODE/
SYNC
ILIM
CIN ～
PULSE
IOUT
RFB1
CFB
FB
RFB2
VDOUT
VDIN
AGND
PGND
* External Components
L (1MHz) : 4.7μH (CDRH4D28C, SUMIDA)
L (2MHz) : 2.2μH (VLCF4020T-2R2N1R7, TDK)
CIN : 10μF (ceramic)
CL : 10μF (ceramic)
RFB1 : 130kΩ
RFB2 : 150kΩ
CFB : 62pF (ceramic)
14/25
L
LX
CL
XC9223/XC9224
Series
■TEST CIRCUITS (Continued)
Circuit ⑤
VIN
A
LX
A
CE
A
A
1μF
A
MODE/
SYNC
ILIM
FB
VDOUT
VDIN
AGND
PGND
A
A
Circuit ⑥
VIN
LX
CE
1μF
MODE/
SYNC
ILIM
A
FB
VDOUT
VDIN
AGND
PGND
Circuit ⑦
VIN
LX
CE
1μF
A
MODE/
200kΩ SYNC
ILIM
VDOUT
AGND
FB
VDIN
PGND
Waveform Measurement Point
15/25
XC9223/XC9224 Series
■TYPICAL PERFORMANCE CHARACTERISTICS
(1) Efficiency vs. Output Current
XC9223B082Ax
XC9223B081Ax
VIN=5V,
FOSC=1MHz,
L=4.7μH (CDRH4D28C),
VIN=5V,
FOSC=1M
Hz, L=4.7uH(CDRH4D28C),
CIN=10μF (ceramic),
CL=10μF (ceramic)
CIN=10uF(ceram
ic), CL=10uF(ceram
ic)
100
90
90
80
80
Efficiency: EFFI (%)
Efficiency: EFFI (%)
100
70
VOUT=3.3V
60
50
VOUT=1.5V
40
30
20
70
VOUT=3.3V
60
50
40
VOUT=1.5V
30
PW M/PFM
PW M
20
PW M/PFM
PW M
10
VIN=5V,
Hz,L=2.2μH
L=2.2uH(CDRH4D28),
VIN=5V,FOSC=2M
FOSC=2MHz,
(CDRH4D28),
ic), CL=10uF(ceram ic)
CCIN=10uF(ceram
IN=10μF (ceramic), CL=10μF (ceramic)
10
0
0
1
10
100
Output Current: IOUT (mA)
1000
1
10
100
Output Current: IOUT (mA)
XC9223B081Ax
90
90
80
80
70
VOUT =2.5V
60
50
VOUT =1.5V
40
30
PWM/PFM
20
VIN=3.3V,FOSC=2MHz
VIN=3.3V, FOSC=2MHz, L=2.2μH
(CDRH4D28),
L=2.2uH(CDRH4D28),CIN=10uF(ceramic),CL=10uF(ceramic)
CIN=10μF (ceramic), CL=10μF (ceramic)
100
Efficiency:
EFFI (%)
Efficiency[%}
Efficiency[%}
Efficiency:
EFFI (%)
XC9223B082Ax
XC9223B081Ax
VIN=3.3V, FOSC=1MHz, L=4.7μH
(CDRH4D28C),
VIN=3.3V,FOSC=1MHz
CIN=10μF (ceramic), CL=10μF (ceramic)
L=4.7uH(CDRH4D28C),CIN=10uF(ceramic),CL=10uF(ceramic)
100
1000
70
VOUT=2.5V
60
50
VOUT=1.5V
40
30
PWM/PFM
20
PWM
PWM
10
10
0
0
1
10
100
1
1000
10
100
1000
Output Current : IOUT (mA)
Output Current : IOUT (mA)
Output Current: IOUT (mA)
Output Current: IOUT (mA)
(2) Output Voltage vs. Output Current
XC9223B081Ax
3.5
PW M Control
PW M Control
1.55
3.4
3.3
3.2
1.5
1.45
PW M/PFM Automatic Switching Control
3.1
PW M/PFM Automatic Switching Control
1.4
3
1
16/25
VIN=5.0V, Topr=25℃,
(CDRH4D28C),
VIN=5.0V,T
opr=25 o C,L=4.7μH
L:4.7uH(CDRH4D28C),
CIN
=10μF (ceramic),
CL=10μF (ceramic)
CIN=10uF(ceram
ic),CL=10uF(ceram
ic)
1.6
Output Voltage: VOUT (V)
3.6
Output Voltage: VOUT (V)
XC9223B082Ax
o
VIN=5.0V,
T opr=25
C, L:4.7uH(CDRH4D28C),
VIN=5.0V,
Topr=25℃,
L=4.7μH (CDRH4D28C),
CIN=10uF(ceram
ic),CL=10uF(ceram
ic)
CIN=10μF (ceramic),
CL=10μF (ceramic)
10
100
Output Current: IOUT (mA)
1000
1
10
100
Output Current: IOUT (mA)
1000
XC9223/XC9224
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(2) Output Voltage vs. Output Current (Continued)
XC9223B082Ax
XC9223B081Ax
VIN=3.3V,T
opr=25 o C,L=4.7μH
L:4.7uH(CDRH4D28C),
VIN=3.3V, Topr=25℃,
(CDRH4D28C),
CIN=10uF(ceram
ic), CL=10uF(ceram ic)
C
IN=10μF (ceramic), CL=10μF (ceramic)
2.8
1.6
PW M Control
2.7
PW M Control
Output Voltage: VOUT (V)
Output Voltage: VOUT (V)
VIN=3.3V, Topr=25℃,
(CDRH4D28C),
VIN=3.3V,T
opr=25 o C, L=4.7μH
L:4.7uH(CDRH4D28C),
C
CL=10μF (ceramic)
CIN=10uF(ceram
ic),CL=10uF(ceram
ic)
IN=10μF (ceramic),
1.55
2.6
2.5
2.4
1.5
PW M/PFM Automatic Switching Control
1.45
PW M/PFM Automatic Switching Control
2.3
2.2
1.4
1
10
100
Output Current: IOUT (mA)
1
1000
(3) Oscillation Frequency vs. Ambient Temperature
10
100
Output Current: IOUT (mA)
(4) U.V.L.O. Voltage vs. Ambient Temperature
XC9223/24 Series
XC9223/XC9224
Series
XC9223/24 SeriesSeries
XC9223/XC9224
2.8
1MHz
2.4
1.00
2
2MHz
0.80
1.6
0.60
-50
-25
0
25
50
75
Ambient Temperature : Ta (oC)
1.2
100
2.8
UVLO Voltage : UVLO1,UVLO2 (V)
Oscillation Frequency: FOSC (MHz)
1.40
1.20
1000
2.6
UVLO2
2.4
2.2
2.0
1.8
1.6
UVLO
1.4
-50
-25
0
25
50
75
Ambient Temperature : Ta (oC)
100
(5) Supply Current 2 vs. Input Voltage
XC9223/24 Series
XC9223/XC9224
Series(2MHz)
(2MHz)
XC9223/XC9224
Series(1MHz)
(1MHz)
XC9223/9424 Series
CE=FB=VIN, M ODE=0V
80
60
40
20
0
CE=FB=VIN, M ODE=0V
100
Supply Current 2: IDD2 (uA)
Supply Current 2: IDD2 (uA)
100
80
60
40
20
0
2
3
4
5
Input Voltage: VIN (V)
6
7
2
3
4
5
Input Voltage: VIN (V)
6
7
17/25
XC9223/XC9224 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(6) Soft Start Time
XC9223/24 Series
XC9223/XC9224
Series
XC9223/XC9224
Series
XC9223/24 Series
VIN=5.0V,VOUT =3.3V,CE=0 → 5V
IOUT =1m A,M ODE=VIN
VIN=5.0V,VOUT =1.5V,CE=0 → 5V
IOUT =1m A,M ODE=0V
CE : 5V/div
CE : 5V/div
VOUT : 1V/div
VOUT : 1V/div
500usec/div
500μs
/ div
500μs
/ div
500usec/div
(7) FB Voltage vs. Supply Voltage
XC9223/9424
Series
XC9223/XC9224
Series
IOUT =0.1m A,T opr=25 o C
FB Voltage: VFB (V)
0.816
0.808
0.800
0.792
0.784
2.0
3.0
4.0
5.0
Input Voltage: VIN (V)
18/25
6.0
7.0
XC9223/XC9224
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(8) Load Transient Response
XC9223B081Ax <1MHz>
VIN=5.0V, VOUT=3.3V, MODE/SYNC=VIN (PWM control)
L=4.7μH (CDRH4D28C), CIN=10μF (ceramic), CL=10μF (ceramic), Topr=25OC
VOUT:200mV/div
VOUT:200mV/div
IOUT=200mA
IOUT=200mA
IOUT=1mA
IOUT=1mA
50usec/div
50μs
/ div
500usec/div
500μs
/ div
VOUT:200mV/div
VOUT:200mV/div
IOUT=800mA
IOUT=800mA
IOUT=200mA
IOUT=200mA
50usec/div
50μs
/ div
500usec/div
500μs
/ div
VIN=5.0V, VOUT=3.3V, MODE/SYNC=0V (PWM/PFM automatic switching control)
L=4.7μH (CDRH4D28C), CIN=10μF (ceramic), CL=10μF (ceramic), Topr=25OC
VOUT:200mV/div
VOUT:200mV/div
IOUT=200mA
IOUT=200mA
IOUT=1mA
IOUT=1mA
50usec/div
50μs
/ div
500usec/div
500μs
/ div
19/25
XC9223/XC9224 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(8) Load Transient Response (Continued)
XC9223B081Ax <1MHz> (Continued)
VIN=5.0V, VOUT=1.5V, MODE/SYNC=VIN (PWM control)
L=4.7μH (CDRH4D28C), CIN=10μF (ceramic), CL=10μF (ceramic), Topr=25OC
VOUT:200mV/div
VOUT:200mV/div
IOUT=200mA
IOUT=200mA
IOUT=1mA
IOUT=1mA
50usec/div
50μs
/ div
200usec/div
200μs
/ div
VOUT:200mV/div
VOUT:200mV/div
IOUT=800mA
IOUT=800mA
IOUT=200mA
IOUT=200mA
50usec/div
50μs
/ div
200usec/div
200μs
/ div
VIN=5.0V, VOUT=1.5V, MODE/SYNC=0V (PWM/PFM automatic switching control)
L=4.7μH (CDRH4D28C), CIN=10μF (ceramic), CL=10μF (ceramic), Topr=25OC
VOUT:200mV/div
VOUT:200mV/div
IOUT=200mA
IOUT=200mA
IOUT=1mA
IOUT=1mA
50μs
/ div
50usec/div
20/25
200μs
/ div
200usec/div
XC9223/XC9224
Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(8) Load Transient Response (Continued)
XC9223B082Ax <2MHz>
VIN=5.0V, VOUT=3.3V, MODE/SYNC=VIN (PWM control)
L=2.2μH (CDRH4D28), CIN=10μF (ceramic), CL=10μF (ceramic), Topr=25OC
VOUT:200mV/div
VOUT:200mV/div
IOUT=200mA
IOUT=200mA
IOUT=1mA
IOUT=1mA
50usec/div
50μs
/ div
500usec/div
500μs
/ div
VOUT:200mV/div
VOUT:200mV/div
IOUT=800mA
IOUT=800mA
IOUT=200mA
IOUT=200mA
500usec/div
500μs
/ div
50usec/div
50μs
/ div
VIN=5.0V, VOUT=3.3V, MODE/SYNC=0V (PWM/PFM automatic switching control)
L=2.2μH (CDRH4D28C), CIN=10μF (ceramic), CL=10μF (ceramic), Topr=25OC
VOUT:200mV/div
VOUT:200mV/div
IOUT=200mA
IOUT=200mA
IOUT=1mA
IOUT=1mA
50usec/div
50μs
/ div
500μs
/ div
500usec/div
21/25
XC9223/XC9224 Series
■TYPICAL PERFORMANCE CHARACTERISTICS (Continued)
(8) Load Transient Response (Continued)
XC9223B082Ax <2MHz> (Continued)
VIN=5.0V, VOUT=1.5V, MODE/SYNC=VIN (PWM control)
L=2.2μH (CDRH4D28), CIN=10μF (ceramic), CL=10μF (ceramic), Topr=25OC
VOUT:200mV/div
VOUT:200mV/div
IOUT=200mA
IOUT=200mA
IOUT=1mA
IOUT=1mA
50usec/div
50μs / div
200usec/div
200μs
/ div
VOUT:200mV/div
VOUT:200mV/div
IOUT=800mA
IOUT=800mA
IOUT=200mA
IOUT=200mA
50μs
/ div
50usec/div
200μs
/ div
200usec/div
VIN=5.0V, VOUT=1.5V, MODE/SYNC=0V (PWM/PFM automatic switching control)
L=2.2μH (CDRH4D28C), CIN=10μF (ceramic), CL=10μF (ceramic), Topr=25OC
VOUT:200mV/div
VOUT:200mV/div
IOUT=200mA
IOUT=200mA
IOUT=1mA
IOUT=1mA
50μs / div
50usec/div
22/25
200usec/div
200μs / div
XC9223/XC9224
Series
■PACKAGE INFORMATION
●USP-10B
●MSOP-10
1 0.15+0.08
2.6+0.15
MAX.0.6
1
0~ 6
3.00+0.10
0.4+0.03
1.6+0.1
1 0.86+0.15
(0.5)
0.2+0.05
0.45+0.05
0.2+0.05
0.2+0.05
0.45+0.05
0.15
0.2
0.325 0.3 0.3
1 0~0.15
+0.1
0.25+0.1
O
0.125
1 0.20 -0.05
AAA
AAAA
1 4.90+0.20
3.00+0.10
1 0.53+0.13
2.9+0.15
0.65
0.1+0.03
0.65
0.5
2.5+0.1
0.5
0.1+0.03
●SOP-8
+0.01
-0.1
+0.40
6.1 -0.30
4.2±0.4
0.4±0.04
0.2
5.0
+0.50
-0.20
10°
1.5±0.1
0～0.25
+0.15
1.58 -0.18
0～
1.27±0.03
0.4±0.1
23/25
XC9223/XC9224 Series
■PACKAGING INFORMATION (Continued)
●USP-10B Recommended Pattern Layout
1.50
0.45
●USP-10B Recommended Metal Mask Design
1.50
1.05
0.80
1.05
0.80
0.35
0.45
1.45
1.10
0.70
1.45
1.10
0.70
0.35
0.20
0.40
0.30
0.10
0.55
0.55
1.05
1.05
0.25
0.075
0.075
0.30
0.10
0.475
0.025
0.25
0.225
0.225
0.25
1.25
1.35
0.475
0.025 0.25
0.025
0.125 0.125 0.125
0.125 0.125 0.125
1.25
1.35
0.025
0.20 0.20
0.15
0.15
0.20
■MARKING RULE
●MSOP-10
10 9
8
7 6
①Represents products series
MARK
0
PRODUCT SERIES
XC9223xxxxAx
A
XC9224xxxxAx
②Represents type of DC/DC converters
① ②③
MARK
B
④ ⑤⑥⑦
PRODUCT SERIES
XC9223/9224BxxxAx
③④Represents reference voltage
MARK
1 2
3
4
MSOP-10
(TOP VIEW)
③
0
5
PRODUCT SERIES
④
8
XC9223/9224x08xAx
⑤Represents oscillation frequency
MARK
1
2
OSCILLATION FREQUENCY
1.0MHz
2.0MHz
PRODUCT SERIES
XC9223/9224xxx1Ax
XC9223/9224xxx2Ax
⑥Represents production lot number
01 to 09, 0A to 0Z, 10 to 19, 1A~ in order. (G, I, J, O, Q, W excepted)
Note: No character inversion used.
ex.)
MARKING
⑥
0
1
24/25
⑦
3
A
PRODUCTION
LOT NUMBER
03
1A
XC9223/XC9224
Series
1. The products and product specifications contained herein are subject to change without
notice to improve performance characteristics.
Consult us, or our representatives
before use, to confirm that the information in this catalog is up to date.
2. We assume no responsibility for any infringement of patents, patent rights, or other
rights arising from the use of any information and circuitry in this catalog.
3. Please ensure suitable shipping controls (including fail-safe designs and aging
protection) are in force for equipment employing products listed in this catalog.
4. The products in this catalog are not developed, designed, or approved for use with such
equipment whose failure of malfunction can be reasonably expected to directly
endanger the life of, or cause significant injury to, the user.
(e.g. Atomic energy; aerospace; transport; combustion and associated safety
equipment thereof.)
5. Please use the products listed in this catalog within the specified ranges.
Should you wish to use the products under conditions exceeding the specifications,
please consult us or our representatives.
6. We assume no responsibility for damage or loss due to abnormal use.
7. All rights reserved. No part of this catalog may be copied or reproduced without the
prior permission of Torex Semiconductor Ltd.
25/25