ZL50233 4 Channel Voice Echo Cancellor Data Sheet Features • • March 2003 Independent multiple channels of echo cancellation; from 4 channels of 64ms to 2 channels of 128ms with the ability to mix channels at 128ms or 64ms in any combination Ordering Information ZL50233/QCC 100-Pin LQFP ZL50233/GDC 208-Ball LBGA Independent Power Down mode for each group of 2 channels for power management -40°C to +85°C • Fully compliant to ITU-T G.165, G.168 (2000) and (2002) specifications • • Passed AT&T voice quality testing for carrier grade echo cancellers. Protection against narrow band signal divergence and instability in high echo environments • • Compatible to ST-BUS and GCI interfaces with 2Mb/s serial PCM data 0 dB to -12 dB level adjusters (3 dB steps) at all signal ports • Offset nulling of all PCM channels • PCM coding, µ/A-Law ITU-T G.711 or sign magnitude • 10 MHz or 20 MHz master clock operation • • Per channel Fax/Modem G.164 2100Hz or G.165 2100Hz phase reversal Tone Disable 3.3 V I/O pads and 1.8V Logic core operation with 5-Volt tolerant inputs • IEEE-1149.1 (JTAG) Test Access Port • Per channel echo canceller parameters control • • Transparent data transfer and mute ZL50232, ZL50233, ZL50234 and ZL50235 have same pinouts in both LQFP and LBGA packages • Fast reconvergence on echo path changes • Fully programmable convergence speeds • Patented Advanced Non-Linear Processor with high quality subjective performance VDD1 (3.3V) Rin Sin Serial to Parallel MCLK Fsel Applications F0i Timing Unit Voice over IP network gateways • Voice over ATM, Frame Relay VDD2 (1.8V) VSS ODE Parallel to Serial Echo Canceller Pool Group 0 Group 1 ECA/ECB ECA/ECB PLL C4i • Rout Sout Note: Refer to Figure 4 for Echo Canceller block diagram RESET Microprocessor Interface DS CS R/W A10-A0 DTA Test Port D7-D0 IRQ TMS TDI TDO TCK TRST Figure 1 - ZL50233 Device Overview 1 ZL50233 Data Sheet • T1/E1/J1 multichannel echo cancellation • Wireless base stations • Echo Canceller pools • DCME, satellite and multiplexer system Description VDD1 NC NC NC NC NC NC NC IC0 IC0 IC0 NC Mclk NC VSS VDD2 IC0 fsel IC0 PLLVDD PLLVSS1 PLLVSS2 VSS VDD1 ZL50233 QC (100 pin LQFP) VDD2 = 1.8V VDD1 = 3.3V NC A9 NC A8 VDD1 VDD2 NC A7 NC A6 NC NC A5 IC0 A4 A10 VSS IC0 VSS A3 A1 A0 NC VDD1 A2 51 49 39 50 38 48 37 47 36 46 35 45 44 34 43 33 42 32 41 40 31 29 30 28 27 26 Figure 2 - 100 Pin LQFP 2 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 NC 76 NC 77 D7 78 D6 79 D5 80 D4 81 D3 82 VSS 83 D2 84 D1 85 D0 86 VDD2 87 DTA 88 8 R/W 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 7 CS 89 6 IC0 RESETB IRQB DS 90 5 TRSTB 91 4 VSS 92 3 TCK 93 97 2 TDO 94 98 1 TDI 95 99 100 TMS 96 NC The ZL50233 Voice Echo Canceller implements a cost effective solution for telephony voice-band echo cancellation conforming to ITU-T G.168 requirements. The ZL50233 architecture contains 2 groups of two echo cancellers (ECA and ECB) which can be configured to provide two channels of 64 milliseconds or one channel of 128 milliseconds echo cancellation. This provides 4 channels of 64 milliseconds to 2 channels of 128 milliseconds echo cancellation or any combination of the two configurations. The ZL50233 supports ITU-T G.165 and G.164 tone disable requirements. Zarlink Semiconductor Inc. NC NC NC IC0 IC0 IC0 VSS IC0 IC0 IC0 IC0 VDD2 C4ib Foib Rin Sin Rout Sout ODE VSS NC NC NC NC NC ZL50233 Data Sheet 1 1 A VSS B IC0 C IC0 2 IC0 VSS 3 4 5 VSS c4i VDD1 VDD1 F0i IC0 6 7 8 9 VSS Sout VDD1 IC0 VSS VSS Rin VSS Rout VDD1 Sin IC0 13 14 VSS VSS IC0 15 16 NC VSS VSS ODE VSS VSS VSS VDD1 VSS VDD2 VSS VDD1 VSS VDD1 VSS VSS VSS VSS NC VSS VDD1 VDD2 VDD1 VSS VDD1 VSS VDD1 VSS VSS VDD1 NC A10 IC0 VDD1 VSS E NC IC0 VSS VSS F NC NC VDD1 VDD1 G NC MCLK VSS VSS VSS VSS VSS H NC Fsel VDD1 VDD1 VSS VSS J NC IC0 VDD2 VDD2 VSS NC IC0 PLLVSS PLLVDD VSS M 12 VSS NC L 11 IC0 D K 10 VDD1 VSS IC0 A9 VSS VDD1 IC0 A8 VSS VDD2 VDD2 NC A7 VSS VSS VSS VSS NC A6 VSS VSS VSS VDD1 VDD1 NC A5 VSS VSS VSS VSS VSS NC A4 ZL50233GD NC NC VSS VSS VDD1 VDD1 NC A3 TDI TMS VDD1 VDD1 VSS VSS VSS A2 TDO TRST VSS VSS VSS VDD1 VSS VDD1 VSS VDD1 VSS VDD2 VSS VDD1 VDD1 A1 TCK VSS VSS VDD1 VSS VDD1 VSS VDD1 VSS VDD1 VSS VDD2 VSS VSS VDD1 A0 IC0 VSS R/W VDD1 DTA VDD1 IRQ VDD1 DS VDD1 CS VSS VSS VSS VDD1 D2 VSS D3 D4 VSS D5 VDD1 D6 VSS D7 VSS N P R VSS T 1 D0 RESET VDD1 VSS D1 - A1 corner is identified by metallized markings. Figure 3 - 208 Ball LBGA Zarlink Semiconductor Inc. 3 ZL50233 Data Sheet Pin Description PIN # PIN Name 208-Ball LBGA VSS A1, A3,A7,A11, A13, 5, 18, 32, Ground. A15, A16, B2, B6, B8, 42, 56, 69, B12, B14, B15, B16, C3, 81, 98 C5, C7, C9, C11, C12, C13, C14, C16, D4, D8, D10, D12, D13, E3, E4, E14, F13, G3, G4, G7, G8, G9, G10, H7, H8, H9, H10, H13, H14, J7, J8, J9, J10, K7, K8, K9, K10, K13, K14, L3, L4, M13, M14, M15, N3, N4, N5, N7, N9, N11, N13, P2, P3, P5, P7, P9,P11, P13, P14, R2, R14, R15, R16, T1, T3, T7, T10, T14, T16 VDD1 A5, A9, B10, C4, C8, 27, 48, 77, Positive Power Supply V DD1. Nominally 3.3 Volt. B4, C10, D3, D5, D7, 100 D9, D11, D14, E13, F3, F4, F14, H3, H4, J13, J14, L13, L14, M3, M4, N6, N8, N10, N14, N15, P4, P6, P8, P10, P15, R4, R6, R8, R10, R12, T5, T12 VDD2 4 Description 100 PIN LQFP C6, D6, J3, J4, N12, P12, G13, G14 14, 37, 64, Positive Power Supply VDD2. Nominally 1.8Volts. 91 IC0 E15, F15, A12, A10, A6, 7, 41, 43, Internal Connection. These pins must be connected to VSS for A2, B1, B3, C1, C2, D2, 65, 66, 67, normal operation. E2, J2, K2, R1 68, 70, 71, 72, 86, 87, 88, 93, 94 NC A14, C15, D1, D15, E1, F1, G1, G15, H1, H15, J1, J15, K1, K15,L1,L15,F2,L2 IRQ R9 24, 25, 26, No connection. These pins must be left open for normal 44, 45, 46, operation. 47, 49, 51, 52, 53, 54, 55, 73, 74, 75, 76, 78, 79, 80, 82, 83, 84, 85, 89, 99, 50 9 Interrupt Request (Open Drain Output). This output goes low when an interrupt occurs in any channel. IRQ returns high when all the interrupts have been read from the Interrupt FIFO Register. A pull-up resistor (1K typical) is required at this output. Zarlink Semiconductor Inc. ZL50233 Data Sheet Pin Description (continued) PIN # PIN Name Description 208-Ball LBGA 100 PIN LQFP DS R11 10 Data Strobe (Input). This active low input works in conjunction with CS to enable the read and write operations. CS R13 11 Chip Select (Input). This active low input is used by a microprocessor to activate the microprocessor port. R/W R5 12 Read/Write (Input). This input controls the direction of the data bus lines (D7-D0) during a microprocessor access. DTA R7 13 Data Transfer Acknowledgment (Open Drain Output). This active low output indicates that a data bus transfer is completed. A pull-up resistor (1K typical) is required at this output. D0..D7 T2,T4,T6,T8,T9,T11, T13,T15 15, 16, 17, Data Bus D0 - D7 (Bidirectional). These pins form the 8-bit 19, 20, 21, bidirectional data bus of the microprocessor port. 22, 23 A0..A10 P16,N16,M16,L16,K16, 28, 29, 30, Address A0 to A10 (Input). These inputs provide the A10 - A0 J16,H16,G16,F16,E16, 31, 33, 34, address lines to the internal registers. D16 35, 36, 38, 39, 40 ODE B13 57 Output Drive Enable (Input). This input pin is logically AND’d with the ODE bit-6 of the Main Control Register. When both ODE bit and ODE input pin are high, the Rout and Sout ST-BUS outputs are enabled. When the ODE bit is low or the ODE input pin is low, the Rout and Sout ST-BUS outputs are high impedance. Sout A8 58 Send PCM Signal Output (Output). Port 1 TDM data output streams. Sout pin outputs serial TDM data streams at 2.048 Mb/s with 4 channels per stream. Rout B9 59 Receive PCM Signal Output (Output). Port 2 TDM data output streams. Rout pin outputs serial TDM data streams at 2.048 Mb/s with 4 channels per stream. Sin B11 60 Send PCM Signal Input (Input). Port 2 TDM data input streams. Sin pin receives serial TDM data streams at 2.048 Mb/s with 4 channels per stream. Rin B7 61 Receive PCM Signal Input (Input). Port 1 TDM data input streams. Rin pin receives serial TDM data streams at 2.048 Mb/s with 4 channels per stream. F0i B5 62 Frame Pulse (Input). This input accepts and automatically identifies frame synchronization signals formatted according to ST-BUS or GCI interface specifications. C4i A4 63 Serial Clock (Input). 4.096 MHz serial clock for shifting data in/out on the serial streams (Rin, Sin, Rout, Sout). MCLK G2 90 Master Clock (Input). Nominal 10MHz or 20MHz Master Clock input. May be connected to an asynchronous (relative to frame signal) clock source. Zarlink Semiconductor Inc. 5 ZL50233 Data Sheet Pin Description (continued) PIN # PIN Name Description 208-Ball LBGA 100 PIN LQFP Fsel H2 92 PLLVss1 PLLVss2 K3 97, 95 PLLVDD K4 96 PLL Power Supply. Must be connected to VDD2 = 1.8V TMS M2 1 Test Mode Select (3.3V Input). JTAG signal that controls the state transitions of the TAP controller. This pin is pulled high by an internal pull-up when not driven. TDI M1 2 Test Serial Data In (3.3V Input). JTAG serial test instructions and data are shifted in on this pin. This pin is pulled high by an internal pull-up when not driven. TDO N1 3 Test Serial Data Out (Output). JTAG serial data is output on this pin on the falling edge of TCK. This pin is held in high impedance state when JTAG scan is not enabled. TCK P1 4 Test Clock (3.3V Input). Provides the clock to the JTAG test logic. TRST N2 6 Test Reset (3.3V Input). Asynchronously initializes the JTAG TAP controller by putting it in the Test-Logic-Reset state. This pin should be pulsed low on power-up or held low, to ensure that the ZL50233 is in the normal functional mode. This pin is pulled by an internal pull-down when not driven. RESET R3 8 Device Reset (Schmitt Trigger Input). An active low resets the device and puts the ZL50233 into a low-power stand-by mode. When the RESET pin is returned to logic high and a clock is applied to the MCLK pin, the device will automatically execute initialization routines, which preset all the Control and Status Registers to their default power-up values. 1.0 Frequency select (Input). This input selects the Master Clock frequency operation. When Fsel pin is low, nominal 20 MHz Master Clock input must be applied. When Fsel pin is high, nominal 10 MHz Master Clock input must be applied. PLL Ground. Must be connected to VSS Device Overview The ZL50233 architecture contains 4 echo cancellers divided into 2 groups. Each group has two echo cancellers, Echo Canceller A and Echo Canceller B. Each group can be configured in Normal, Extended Delay or Back-toBack configurations. In Normal configuration, a group of echo cancellers provides two channels of 64ms echo cancellation, which run independently on different channels. In Extended Delay configuration, a group of echo cancellers achieves 128ms of echo cancellation by cascading the two echo cancellers (A & B). In Back-to-Back configuration, the two echo cancellers from the same group are positioned to cancel echo coming from both directions in a single channel, providing full-duplex 64ms echo cancellation. 6 Zarlink Semiconductor Inc. ZL50233 Data Sheet Each echo canceller contains the following main elements (see Figure 4). • Adaptive Filter for estimating the echo channel • Subtractor for cancelling the echo • Double-Talk detector for disabling the filter adaptation during periods of double-talk • • • Path Change detector for fast reconvergence on major echo path changes Instability Detector to combat instability in very low ERL environments Patented Advanced Non-Linear Processor for suppression of residual echo, with comfort noise injection • Disable Tone Detectors for detecting valid disable tones at send and receive path inputs • Narrow-Band Detector for preventing Adaptive Filter divergence from narrow-band signals • Offset Null filters for removing the DC component in PCM channels • 0 to -12dB level adjusters at all signal ports • Parallel controller interface compatible with Motorola microcontrollers • PCM encoder/decoder compatible with µ/A-Law ITU-T G.711 or Sign-Magnitude coding Each echo canceller in the ZL50233 has four functional states: Mute, Bypass, Disable Adaptation and Enable Adaptation. These are explained in the section entitled Echo Canceller Functional States. µ/A-Law/ Linear 0 to -12dB Level Adjust Offset Null Σ Non-Linear Processor Adaptive Filter Disable Tone Detector Instability Detector Linear/ µ/A-Law Microprocessor Interface MuteS Double - Talk Detector Path Change Detector Narrow-Band Detector Rout (channel N) 0 to -12dB Level Adjust Control Sin (channel N) Linear/ µ/A-Law 0 to -12dB Level Adjust 0 to -12dB Level Adjust MuteR Sout (channel N) Disable Tone Detector Offset Null µ/A-Law/ Linear Rin (channel N) Echo Canceller (N), where 0 < N < 3 Programmable Bypass Figure 4 - Functional Block Diagram 1.1 Adaptive Filter The adaptive filter adapts to the echo path and generates an estimate of the echo signal. This echo estimate is then subtracted from Sin. For each group of echo cancellers, the adaptive filter is a 1024 tap FIR adaptive filter which is divided into two sections. Each section contains 512 taps providing 64ms of echo estimation. In Normal configuration, the first section is dedicated to channel A and the second section to channel B. In Extended Delay configuration, both sections are cascaded to provide 128ms of echo estimation in channel A. In Back-to Back configuration, the first section is used in the receive direction and the second section is used in the transmit direction for the same channel. Zarlink Semiconductor Inc. 7 ZL50233 1.2 Data Sheet Double-Talk Detector Double-Talk is defined as those periods of time when signal energy is present in both directions simultaneously. When this happens, it is necessary to disable the filter adaptation to prevent divergence of the Adaptive Filter coefficients. Note that when double-talk is detected, the adaptation process is halted but the echo canceller continues to cancel echo using the previous converged echo profile. A double-talk condition exists whenever the relative signal levels of Rin (Lrin) and Sin (Lsin) meet the following condition: Lsin > Lrin + 20log 10(DTDT) where DTDT is the Double-Talk Detection Threshold. Lsin and Lrin are signal levels expressed in dBm0. A different method is used when it is uncertain whether Sin consists of a low level double-talk signal or an echo return. During these periods, the adaptation process is slowed down but it is not halted. The slow convergence speed is set using the Slow sub-register in Control Register 4. During slow convergence, the adaptation speed is reduced by a factor of 2Slow relative to normal convergence for non-zero values of Slow. If Slow equals zero, adaptation is halted completely. In the G.168 standard, the echo return loss is expected to be at least 6 dB. This implies that the Double-Talk Detector Threshold (DTDT) should be set to 0.5 (-6 dB). However, in order to achieve additional guardband, the DTDT is set internally to 0.5625 (-5 dB). In some applications the return loss can be higher or lower than 6 dB. The ZL50233 allows the user to change the detection threshold to suit each application’s need. This threshold can be set by writing the desired threshold value into the DTDT register. The DTDT register is 16 bits wide. The register value in hexadecimal can be calculated with the following equation: DTDT(hex) = hex(DTDT(dec) * 32768) where 0 < DTDT(dec) < 1 Example: For DTDT = 0.5625 (-5 dB), the hexadecimal value becomes hex( 0.5625 * 32768) = 4800 hex 1.3 Path Change Detector Integrated into the ZL50233 is a Path Change Detector. This permits fast reconvergence when a major change occurs in the echo channel. Subtle changes in the echo channel are also tracked automatically once convergence is achieved, but at a much slower speed. The Path Change Detector is activated by setting the PathDet bit in Control Register 3 to “1”. An optional path clearing feature can be enabled by setting the PathClr bit in Control Register 3 to “1”. With path clearing turned on, the existing echo channel estimate will also be cleared (i.e. the adaptive filter will be filled with zeroes) upon detection of a major path change. 8 Zarlink Semiconductor Inc. ZL50233 Data Sheet 1.4 Non-Linear Processor (NLP) After echo cancellation, there is always a small amount of residual echo which may still be audible. The ZL50233 uses Zarlink’s patented Advanced NLP to remove residual echo signals which have a level lower than the Adaptive Suppression Threshold (TSUP in G.168). This threshold depends upon the level of the Rin (Lrin) reference signal as well as the programmed value of the Non-Linear Processor Threshold register (NLPTHR). TSUP can be calculated by the following equation: TSUP = Lrin + 20log10 (NLPTHR) where NLPTHR is the Non-Linear Processor Threshold register value and Lrin is the relative power level expressed in dBm0. The NLPTHR register is 16 bits wide. The register value in hexadecimal can be calculated with the following equation: NLPTHR(hex) = hex(NLPTHR (dec) * 32768) where 0 < NLPTHR(dec) < 1 When the level of residual error signal falls below TSUP, the NLP is activated further attenuating the residual signal by an additional 30 dB. To prevent a perceived decrease in background noise due to the activation of the NLP, a spectrally-shaped comfort noise, equivalent in power level to the background noise, is injected. This keeps the perceived noise level constant. Consequently, the user does not hear the activation and de-activation of the NLP. The NLP processor can be disabled by setting the NLPDis bit to “1” in Control Register 2. The comfort noise injector can be disabled by setting the INJDis bit to “1” in Control Register 1. It should be noted that the NLPTHR is valid and the comfort noise injection is active only when the NLP is enabled. The patented Advanced NLP provides a number of new and improved features over the original NLP found in previous generation devices. Differences between the Advanced NLP and the original NLP are summarized in Table 1. Feature Register or Bit(s) Advanced NLP Default Value Original NLP Default Value NLP Selection NLPSel (Control Register 3) 1 0 (feature not supported) Reject uncanceled echo as noise NLRun1 (Control Register 3) 1 0 (feature not supported) Reject double-talk as noise NLRun2 (Control Register 3) 1 0 (feature not supported) Noise level estimator ramping scheme InjCtrl (Control Register 3) 1 0 (feature not supported) Noise level ramping rate NLInc (Noise Control) 5(hex) C(hex) Noise level scaling Noise Scaling 16(hex) 74(hex) Table 1 - Comparison of NLP Types The NLPSel bit in Control Register 3 selects which NLP is used. A “1” will select the Advanced NLP, “0” selects the original NLP. ( See page 23 for Control Register 3 bit description) The Advanced NLP uses a new noise ramping scheme to quickly and more accurately estimate the background noise level. The noise ramping method of the original NLP can also be used. The InjCtrl bit in Control Register 3 selects the ramping scheme. Zarlink Semiconductor Inc. 9 ZL50233 Data Sheet The NLInc sub-register in Noise Control is used to set the ramping speed. When InjCtrl = 1 (such as with the Advanced NLP), a lower value will give faster ramping. When InjCtrl = 0 (such as with the original NLP), a higher value will give faster ramping. NLInc is a 4-bit value, so only values from 0 to F(hex) are valid. The Noise Scaling register can be used to adjust the relative volume of the comfort noise. Lowering this value will scale the injected noise level down, conversely, raising the value will scale the comfort noise up. Due to differences in the noise estimator operation, the Advanced NLP requires a different scaling value than the original NLP. IMPORTANT NOTE: NLInc and the Noise Scaling register have been pre-programmed with G.168 compliant values. Changing these values may result in undesirable comfort noise performance! The Advanced NLP also contains safeguards to prevent double-talk and uncancelled echo from being mistaken for background noise. These features were not present in the original NLP. They can be disabled by setting the NLRun1 and NLRun2 bits in Control Register 3 to “0”. 1.5 Disable Tone Detector The G.165 recommendation defines the disable tone as having the following characteristics: 2100 Hz (±21Hz) sine wave, a power level between -6 to -31 dBm0, and a phase reversal of 180 degrees (± 25 degrees) every 450 ms (±25 ms). If the disable tone is present for a minimum of one second with at least one phase reversal, the Tone Detector will trigger. The G.164 recommendation defines the disable tone as a 2100 Hz (+21 Hz) sine wave with a power level between 0 to -31 dBm0. If the disable tone is present for a minimum of 400 ms, with or without phase reversal, the Tone Detector will trigger. The ZL50233 has two Tone Detectors per channels (for a total of 8) in order to monitor the occurrence of a valid disable tone on both Rin and Sin. Upon detection of a disable tone, TD bit of the Status Register will indicate logic high and an interrupt is generated (i.e. IRQ pin low). Refer to Figure 5 and to the Interrupts section. Rin Tone Detector Sin Tone Detector ECA Status reg TD bit Echo Canceller A Rin Tone Detector Sin Tone Detector ECB Status reg TD bit Echo Canceller B Figure 5 - Disable Tone Detection Once a Tone Detector has been triggered, there is no longer a need for a valid disable tone (G.164 or G.165) to maintain Tone Detector status (i.e. TD bit high). The Tone Detector status will only release (i.e. TD bit low) if the signals Rin and Sin fall below -30 dBm0, in the frequency range of 390 Hz to 700 Hz, and below -34 dBm0, in the frequency range of 700 Hz to 3400 Hz, for at least 400 ms. Whenever a Tone Detector releases, an interrupt is generated (i.e. IRQ pin low). The selection between G.165 and G.164 tone disable is controlled by the PHDis bit in Control Register 2 on a per channel basis. When the PHDis bit is set to “1”, G.164 tone disable requirements are selected. In response to a valid disable tone, the echo canceller must be switched from the Enable Adaptation state to the Bypass state. This can be done in two ways, automatically or externally. In automatic mode, the Tone Detectors internally control the switching between Enable Adaptation and Bypass states. The automatic mode is activated by setting the AutoTD bit in Control Register 2 to high. In external mode, an external controller is needed to service the 10 Zarlink Semiconductor Inc. ZL50233 Data Sheet interrupts and poll the TD bits in the Status Registers. Following the detection of a disable tone (TD bit high) on a given channel, the external controller must switch the echo canceller from Enable Adaptation to Bypass state. 1.6 Instability Detector In systems with very low echo channel return loss (ERL), there may be enough feedback in the loop to cause stability problems in the adaptive filter. This instability can result in variable pitched ringing or oscillation. Should this ringing occur, the Instability Detector will activate and suppress the oscillations. The Instability Detector is activated by setting the RingClr bit in Control Register 3 to “1”. 1.7 Narrow Band Signal Detector (NBSD) Single or dual frequency tones (i.e. DTMF tones) present in the receive input (Rin) of the echo canceller for a prolonged period of time may cause the Adaptive Filter to diverge. The Narrow Band Signal Detector (NBSD) is designed to prevent this by detecting single or dual tones of arbitrary frequency, phase, and amplitude. When narrow band signals are detected, adaptation is halted but the echo canceller continues to cancel echo. The NBSD will be active regardless of the Echo Canceller functional state. However the NBSD can be disabled by setting the NBDis bit to “1” in Control Register 2. 1.8 Offset Null Filter Adaptive filters in general do not operate properly when a DC offset is present at any input. To remove the DC component, the ZL50233 incorporates Offset Null filters in both Rin and Sin inputs. The offset null filters can be disabled by setting the HPFDis bit to “1” in Control Register 2. 1.9 Adjustable Level Pads The ZL50233 provides adjustable level pads at Rin, Rout, Sin and Sout. This setup allows signal strength to be adjusted both inside and outside the echo path. Each signal level may be independently scaled with anywhere from 0 to -12 dB level, in 3 dB steps. Level values are set using the Gains register. CAUTION: Gain adjustment can help interface the ZL50233 to a particular system in order to provide optimum echo cancellation, but it can also degrade performance if not done carefully. Excessive loss may cause low signal levels and slow convergence. Exercise great care when adjusting these values. The -12 dB PAD bit in Control Register 1 is still supported as a legacy feature. Setting this bit will provide 12 dB of attenuation at Rin, and override the values in the Gains register. 1.10 ITU-T G.168 Compliance The ZL50233 has been certified G.168 (1997), (2000) and (2002) compliant in all 64 ms cancellation modes (i.e. Normal and Back-to-Back configurations) by in-house testing with the DSPG ECT-1 echo canceller tester. The ZL50233 has also been tested for G.168 compliance and all voice quality tests at AT&T Labs. The ZL50233 was classified as “carrier grade” echo canceller. Zarlink Semiconductor Inc. 11 ZL50233 2.0 Data Sheet Device Configuration The ZL50233 architecture contains 4 echo cancellers divided into 2 groups. Each group has two echo cancellers which can be individually controlled (Echo Canceller A (ECA) and Echo Canceller B (ECB)). They can be set in three distinct configurations: Normal, Back-to-Back, and Extended Delay. See Figures 6, 7, and 8. 2.1 Normal Configuration In Normal configuration, the two echo cancellers (Echo Canceller A and B) are positioned in parallel, as shown in Figure 6, providing 64 milliseconds of echo cancellation in two channels simultaneously. Sin channel A Sout + - echo path A Adaptive Filter (64ms) channel A Rout Rin PORT2 PORT1 ECA channel B + - echo path B Adaptive Filter (64ms) channel B ECB Figure 6 - Normal Device Configuration (64ms) 2.2 Back-to-Back Configuration In Back-to-Back configuration, the two echo cancellers from the same group are positioned to cancel echo coming from both directions in a single channel providing full-duplex 64ms echo cancellation. See Figure 7. This configuration uses only one timeslot on PORT1 and PORT2 and the second timeslot normally associated with ECB contains zero code. Back-to-Back configuration allows a no-glue interface for applications where bidirectional echo cancellation is required. Sout + Sin echo path Adaptive Filter (64ms) Adaptive Filter (64ms) echo path Rout PORT2 ECA + Rin ECB PORT1 Figure 7 - Back-to-Back Device Configuration (64ms) 12 Zarlink Semiconductor Inc. ZL50233 Data Sheet Back-to-Back configuration is selected by writing a “1” into the BBM bit of Control Register 1 for both Echo Canceller A and Echo Canceller B for a given group of echo canceller. Table 4 shows the 2 groups of 2 cancellers that can be configured into Back-to-Back. Examples of Back-to-Back configuration include positioning one group of echo cancellers between a codec and a transmission device or between two codecs for echo control on analog trunks. 2.3 Extended Delay configuration In this configuration, the two echo cancellers from the same group are internally cascaded into one 128 milliseconds echo canceller. See Figure 8. This configuration uses only one timeslot on PORT1 and PORT2 and the second timeslot normally associated with ECB contains quiet code. Sin channel A + Sout echo path A Adaptive Filter (128 ms) channel A Rout Rin PORT2 PORT1 ECA Figure 8 - Extended Delay Configuration (128ms) Extended Delay configuration is selected by writing a “1” into the ExtDl bit in Echo Canceller A, Control Register 1. For a given group, only Echo Canceller A, Control Register 1, has the ExtDl bit. For Echo Canceller B Control Register 1, Bit 0 must always be set to zero. Table 4 shows the 2 groups of 2 cancellers that can each be configured into 64ms or 128ms echo tail capacity. 3.0 Echo Canceller Functional States Each echo canceller has four functional states: Mute, Bypass, Disable Adaptation and Enable Adaptation. 3.1 Mute In Normal and in Extended Delay configurations, writing a “1” into the MuteR bit replaces Rin with quiet code which is applied to both the Adaptive Filter and Rout. Writing a “1” into the MuteS bit replaces the Sout PCM data with quiet code. +Zero (quiet code) LINEAR 16 bits 2’s complement SIGN/ MAGNITUDE µ-Law A-Law 0000 hex 80hex CCITT (G.711) µ-Law A-Law FFhex D5hex Table 2 - Quiet PCM Code Assignment Zarlink Semiconductor Inc. 13 ZL50233 Data Sheet In Back-to-Back configuration, writing a “1” into the MuteR bit of Echo Canceller A, Control Register 2, causes quiet code to be transmitted on Rout. Writing a “1” into the MuteS bit of Echo Canceller A, Control Register 2, causes quiet code to be transmitted on Sout. In Extended Delay and in Back-to-Back configurations, MuteR and MuteS bits of Echo Canceller B must always be “0”. Refer to Figure 4 and to Control Register 2 for bit description. 3.2 Bypass The Bypass state directly transfers PCM codes from Rin to Rout and from Sin to Sout. When Bypass state is selected, the Adaptive Filter coefficients are reset to zero. Bypass state must be selected for at least one frame (125 µs) in order to properly clear the filter. 3.3 Disable Adaptation When the Disable Adaptation state is selected, the Adaptive Filter coefficients are frozen at their current value. The adaptation process is halted, however, the echo canceller continues to cancel echo. 3.4 Enable Adaptation In Enable Adaptation state, the Adaptive Filter coefficients are continually updated. This allows the echo canceller to model the echo return path characteristics in order to cancel echo. This is the normal operating state. The echo canceller functions are selected in Control Register 1 and Control Register 2 through four control bits: MuteS, MuteR, Bypass and AdaptDis. Refer to the Registers Description for details. 4.0 ZL50233 Throughput Delay The throughput delay of the ZL50233 varies according to the device configuration. For all device configurations, Rin to Rout has a delay of two frames and Sin to Sout has a delay of three frames. In Bypass state, the Rin to Rout and Sin to Sout paths have a delay of two frames. 5.0 Serial PCM I/O channels There are two sets of TDM I/O streams, each with channels numbered from 0 to 31. One set of input streams is for Receive (Rin) channels, and the other set of input streams is for Send (Sin) channels. Likewise, one set of output streams is for Rout PCM channels, and the other set is for Sout channels. See Figure 9 for channel allocation. The arrangement and connection of PCM channels to each echo canceller is a 2 port I/O configuration for each set of PCM Send and Receive channels, as illustrated in Figure 9. 5.1 Serial Data Interface Timing The ZL50233 provides ST-BUS and GCI interface timing. The Serial Interface clock frequency, C4i, is 4.096 MHz. The input and output data rate of the ST-BUS and GCI bus is 2.048 Mb/s. The 8 KHz input frame pulse can be in either ST-BUS or GCI format. The ZL50233 automatically detects the presence of an input frame pulse and identifies it as either ST-BUS or GCI. In ST-BUS format, every second falling edge of the C4i clock marks a bit boundary, and the data is clocked in on the rising edge of C4i, three quarters of the way into the bit cell (See Figure 12). In GCI format, every second rising edge of the C4i clock marks the bit boundary, and data is clocked in on the second falling edge of C4i, half the way into the bit cell (see Figure 13). 14 Zarlink Semiconductor Inc. ZL50233 Data Sheet 125 µsec F0i ST-BUS 15.625 µsec F0i GCI interface Active Channels Rin/Sin Rout/Sout 0 1 2 3 Disabled Channels with Random Data Note: Refer to Figure 12 and Figure 13 for timing details. Figure 9 - ST-BUS and GCI Interface Channel Assignment for 2Mb/s Data Streams Base Address + MS Byte LS Byte - 00h - Echo Canceller A Base Address + Echo Canceller B MS Byte LS Byte Control Reg 1 - 20h Control Reg 1 01h Control Reg 2 - 21h Control Reg 2 - 02h Status Reg - 22h Status Reg - 03h Reserved - 23h Reserved - 04h Flat Delay Reg - 24h Flat Delay Reg - 05h Reserved - 25h Reserved - 06h Decay Step Size Reg - 26h Decay Step Size Reg - 07h Decay Step Number - 27h Decay Step Number - 08h Control Reg 3 - 28h Control Reg 3 - 09h Control Reg 4 - 29h Control Reg 4 - 0Ah Noise Scaling - 2Ah Noise Scaling - 0Bh Noise Control - 2Bh Noise Control 0Dh 0Ch Rin Peak Detect Reg 2Dh 2Ch Rin Peak Detect Reg 0Fh 0Eh Sin Peak Detect Reg 2Fh 2Eh Sin Peak Detect Reg 11h 10h Error Peak Detect Reg 31h 30h Error Peak Detect Reg 13h 12h Reserved 33h 32h Reserved 15h 14h DTDT Reg 35h 34h DTDT Reg 17h 16h Reserved 37h 36h Reserved 19h 18h NLPTHR 39h 38h NLPTHR 1Bh 1Ah Step Size, MU 3Bh 3Ah Step Size, MU 1Dh 1Ch Gains 3Dh 3Ch Gains 1Fh 1Eh Reserved 3Fh 3Eh Reserved Table 3 - Memory Mapping of Per Channel Control and Status Registers Zarlink Semiconductor Inc. 15 ZL50233 6.0 Data Sheet Memory Mapped Control and Status registers Internal memory and registers are memory mapped into the address space of the HOST interface. The internal dual ported memory is mapped into segments on a “per channel” basis to monitor and control each individual echo canceller and associated PCM channels. For example, in Normal configuration, echo canceller #3 makes use of Echo Canceller B from group 2. It occupies the internal address space from 060hex to 07Fhex and interfaces to PCM channel #3 on all serial PCM I/O streams. As illustrated in Table 3, the “per channel” registers provide independent control and status bits for each echo canceller. Figure 10 shows the memory map of the control/status register blocks for all echo cancellers. When Extended Delay or Back-to-Back configuration is selected, Control Register 1 of ECA and ECB and Control Register 2 of the selected group of echo cancellers require special care. Refer to the Register description section. Table 4 is a list of the channels used for the 16 groups of echo cancellers when they are configured as Extended Delay or Back-to-Back. 6.1 Normal Configuration For a given group (group 0 to 1), 2 PCM I/O channels are used. For example, group 1 Echo Cancellers A and B, channels 2 and 3 are active. Group Channels 0 0, 1 1 2, 3 Table 4 - Group and Channel allocation 6.2 Extended Delay Configuration For a given group (group 0 or 1), only one PCM I/O channel is active (Echo Canceller A) and the other channel carries quiet code. For example, group 0, Echo Canceller A (Channel 0) will be active and Echo Canceller B (Channel 1) will carry quiet code. 6.3 Back-to-Back Configuration For a given group (group 0 or 1), only one PCM I/O channel is active (Echo Canceller A) and the other channel carries quiet code. For example, group 1, Echo Canceller A (Channel 2) will be active and Echo Canceller B (Channel 3) will carry quiet code. Group 0 Echo Cancellers Registers Channel 0, ECA Ctrl/Stat Registers 0000h --> 001Fh Channel 1, ECB Ctrl/Stat Registers 0020h --> 003Fh Group 1 Echo Cancellers Registers Channel 2, ECA Ctrl/Stat Registers 0040h --> 005Fh Channel 3, ECB Ctrl/Stat Registers 0060h --> 007Fh Main Control Registers <7:0> 0400h --> 0407h Interrupt FIFO Register 0410h Test Register 0411h Reserved Test Register 0412h ---> FFFFh Figure 10 - Memory Mapping 16 Zarlink Semiconductor Inc. ZL50233 Data Sheet 6.4 Power Up Sequence On power up, the RESET pin must be held low for 100 µs. Forcing the RESET pin low will put the ZL50233 in power down state. In this state, all internal clocks are halted, D<7:0>, Sout, Rout, DTA and IRQ pins are tristated. The 8 Main Control Registers, the Interrupt FIFO Register and the Test Register are reset to zero. When the RESET pin returns to logic high and a valid MCLK is applied, the user must wait 500 µs for the PLL to lock. C4i and F0i can be active during this period. Once the PLL has locked, the user must power up the 2 groups of echo cancellers individually, by writing a “1” into the PWUP bit in each group of echo canceller’s Main Control Register. For each group of echo cancellers, when the PWUP bit toggles from zero to one, echo cancellers A and B execute their initialization routine. The initialization routine sets their registers, Base Address+00hex to Base Address+3Fhex, to the default Reset Value and clears the Adaptive Filter coefficients. Two frames are necessary for the initialization routine to execute properly. Once the initialization routine is executed, the user can set the per channel Control Registers, Base Address+00hex to Base Address+3Fhex, for the specific application. 6.5 Power management Each group of echo cancellers can be placed in Power Down mode by writing a “0” into the PWUP bit in their respective Main Control Register. When a given group is in Power Down mode, the corresponding PCM data are bypassed from Rin to Rout and from Sin to Sout with two frames delay. Refer to the Main Control Register section for description. The typical power consumption can be calculated with the following equation: PC = 9 * Nb_of_groups + 3.6, in mW where 0 ≤ Nb_of_groups ≤ 2. 6.6 Call Initialization To ensure fast initial convergence on a new call, it is important to clear the Adaptive Filter. This is done by putting the echo canceller in bypass mode for at least one frame (125 µs) and then enabling adaptation. Since the Narrow Band Detector is “ON” regardless of the functional state of Echo Canceller it is recommended that the Echo cancellers are reset before any call progress tones are applied. 6.7 Interrupts The ZL50233 provides an interrupt pin (IRQ) to indicate to the HOST processor when a G.164 or G.165 Tone Disable is detected and released. Although the ZL50233 may be configured to react automatically to tone disable status on any input PCM voice channels, the user may want for the external HOST processor to respond to Tone Disable information in an appropriate application-specific manner. Each echo canceller will generate an interrupt when a Tone Disable occurs and will generate another interrupt when a Tone Disable releases. Upon receiving an IRQ, the HOST CPU should read the Interrupt FIFO Register. This register is a FIFO memory containing the channel number of the echo canceller that has generated the interrupt. All pending interrupts from any of the echo cancellers and their associated input channel number are stored in this FIFO memory. The IRQ always returns high after a read access to the Interrupt FIFO Register. The IRQ pin will toggle low for each pending interrupt. Zarlink Semiconductor Inc. 17 ZL50233 Data Sheet After the HOST CPU has received the channel number of the interrupt source, the corresponding per channel Status Register can be read from internal memory to determine the cause of the interrupt (see Table 3 for address mapping of Status register). The TD bit indicates the presence of a Tone Disable. The MIRQ bit 5 in the Main Control Register 0 masks interrupts from the ZL50233. To provide more flexibility, the MTDBI (bit-4) and MTDAI (bit-3) bits in the Main Control Register<3:0> allow Tone Disable to be masked or unmasked from generating an interrupt on a per channel basis. Refer to the Registers Description section. 7.0 JTAG Support The ZL50233 JTAG interface conforms to the Boundary-Scan standard IEEE1149.1. This standard specifies a design-for-testability technique called Boundary-Scan test (BST). The operation of the Boundary Scan circuitry is controlled by an Test Access Port (TAP) controller. JTAG inputs are 3.3 Volts compliant only. 7.1 Test Access Port (TAP) The TAP provides access to many test functions of the ZL50233. It consists of four input pins and one output pin. The following pins are found on the TAP. • Test Clock Input (TCK) The TCK provides the clock for the test logic. The TCK does not interfere with any on-chip clock and thus remains independent. The TCK permits shifting of test data into or out of the Boundary-Scan register cells concurrent with the operation of the device and without interfering with the on-chip logic. • Test Mode Select Input (TMS) The logic signals received at the TMS input are interpreted by the TAP Controller to control the test operations. The TMS signals are sampled at the rising edge of the TCK pulse. This pin is internally pulled to VDD1 when it is not driven from an external source. • Test Data Input (TDI) Serial input data applied to this port is fed either into the instruction register or into a test data register, depending on the sequence previously applied to the TMS input. Both registers are described in a subsequent section. The received input data is sampled at the rising edge of TCK pulses. This pin is internally pulled to VDD1 when it is not driven from an external source. • Test Data Output (TDO) Depending on the sequence previously applied to the TMS input, the contents of either the instruction register or data register are serially shifted out towards the TDO. The data from the TDO is clocked on the falling edge of the TCK pulses. When no data is shifted through the Boundary Scan cells, the TDO driver is set to a high impedance state. • Test Reset (TRST) This pin is used to reset the JTAG scan structure. This pin is internally pulled to VSS. 7.2 Instruction Register In accordance with the IEEE 1149.1 standard, the ZL50233 uses public instructions. The JTAG Interface contains a 3-bit instruction register. Instructions are serially loaded into the instruction register from the TDI when the TAP Controller is in its shifted-IR state. Subsequently, the instructions are decoded to achieve two basic functions: to select the test data register that will operate while the instruction is current, and to define the serial test data register path, which is used to shift data between TDI and TDO during data register scanning. 18 Zarlink Semiconductor Inc. ZL50233 Data Sheet 7.3 Test Data Registers As specified in IEEE 1149.1, the ZL50233 JTAG Interface contains three test data registers: • Boundary-Scan register The Boundary-Scan register consists of a series of Boundary-Scan cells arranged to form a scan path around the boundary of the ZL50233 core logic. • Bypass Register The Bypass register is a single stage shift register that provides a one-bit path from TDI to TDO. • Device Identification register The Device Identification register provides access to the following encoded information: device version number, part number and manufacturer's name. 8.0 Register Description Echo Canceller A (ECA): Control Register 1 Power-up 00hex Bit 7 Reset Bit 6 INJDis Bit 5 BBM R/W Address: 00hex + Base Address Bit 4 PAD Bit 3 Bypass Bit 2 AdpDis Bit 1 0 Bit 0 ExtDI Functional Description of Register Bits Reset When high, the power-up initialization is executed. This presets all register bits including this bit and clears the Adaptive Filter coefficients. INJDis When high, the noise injection process is disabled. When low noise injection is enabled. BBM When high, the Back to Back configuration is enabled. When low, the Normal configuration is enabled. Note: Do not enable Extended-Delay and BBM configurations at the same time. Always set both BBM bits of the two echo cancellers (Control Register 1) of the same group to the same logic value to avoid conflict. PAD When high, 12dB of attenuation is inserted into the Rin to Rout path. When low, the Gains register controls the signal levels. Bypass When high, Sin data is by-passed to Sout and Rin data is by-passed to Rout. The Adaptive Filter coefficients are set to zero and the filter adaptation is stopped. When low, output data on both Sout and Rout is a function of the echo canceller algorithm. When high, echo canceller adaptation is disabled. The Voice Processor cancels echo. When low, the echo canceller dynamically adapts to the echo path characteristics. Bits marked as “1” or “0” are reserved bits and should be written as indicated. When high, Echo Cancellers A and B of the same group are internally cascaded into one 128ms echo canceller. When low, Echo Cancellers A and B of the same group operate independently. AdpDis 0 ExtDl Zarlink Semiconductor Inc. 19 ZL50233 Data Sheet Echo Canceller B (ECB): Control Register 1 Power-up 02hex Bit 7 Reset Reset INJDis R/W Address: 20hex + Base Address Bit 6 INJDis Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 BBM PAD Bypass AdpDis 1 0 Functional Description of Register Bits When high, the power-up initialization is executed which presets all register bits including this bit and clears the Adaptive Filter coefficients. When high, the noise injection process is disabled. When low, noise injection is enabled. BBM When high, the Back to Back configuration is enabled. When low, the Normal configuration is enabled. Note: Do not enable Extended-Delay and BBM configurations at the same time. Always set both BBM bits of the two echo cancellers (Control Register 1) of the same group to the same logic value to avoid conflict. PAD When high, 12dB of attenuation is inserted into the Rin to Rout path. When low, the Gains register controls the signal levels. Bypass When high, Sin data is by-passed to Sout and Rin data is by-passed to Rout. The Adaptive Filter coefficients are set to zero and the filter adaptation is stopped. When low, output data on both Sout and Rout is a function of the echo canceller algorithm. When high, echo canceller adaptation is disabled. The Voice Processor cancels echo. When low, the echo canceller dynamically adapts to the echo path characteristics. Bits marked as “1” or “0” are reserved bits and should be written as indicated. Control Register 1 (Echo Canceller B) Bit 0 is a reserved bit and should be written “0”. AdpDis 1 0 Power-up 00hex Bit 7 TDis Bit 6 PHDis Bit 5 NLPDis ECA: Control Register 2 R/W Address: 01hex + Base Address ECB: Control Register 2 R/W Address: 21hex + Base Address Bit 4 AutoTD Bit 3 NBDis Bit 2 HPFDis Bit 1 MuteS Bit 0 MuteR Functional Description of Register Bits TDis PHDis When high, tone detection is disabled. When low, tone detection is enabled. When both Echo Cancellers A and B TDis bits are high, Tone Disable processors are disabled entirely and are put into Power Down mode. When high, the tone detectors will trigger upon the presence of a 2100 Hz tone regardless of the presence/absence of periodic phase reversals. When low, the tone detectors will trigger only upon the presence of a 2100 Hz tone with periodic phase reversals. NLPDis When high, the non-linear processor is disabled. When low, the non-linear processors function normally. Useful for G.165 conformance testing. AutoTD When high, the echo canceller puts itself in Bypass mode when the tone detectors detect the presence of 2100 Hz tone. See PHDis for qualification of 2100 Hz tones. When low, the echo canceller algorithm will remain operational regardless of the state of the 2100 Hz tone detectors. NBDis HPFDis When high, the narrow-band detector is disabled. When low, the narrow-band detector is enabled. When high, the offset nulling high pass filters are bypassed in the Rin and Sin paths. When low, the offset nulling filters are active and will remove DC offsets on PCM input signals. When high, data on Sout is muted to quiet code. When low, Sout carries active code. When high, data on Rout is muted to quiet code. When low, Rout carries active code. MuteS MuteR Note: In order to correctly write to Control Register 1 and 2 of ECB, it is necessary to write the data twice to the register, one immediately after another. The two writes must be separated by at least 350ns and no more than 20us. 20 Zarlink Semiconductor Inc. ZL50233 Data Sheet Power-up 00 hex Bit 7 Reserve Bit 6 TD ECA: Status Register R/W Address: 02 hex + Base Address ECB: Status Register R/W Address: 22 hex + Base Address Bit 5 Bit 4 Bit 3 Bit 2 DTDet Reserve Reserve Reserve Functional Description of Register Bits Bit 1 TDG Bit 0 NB Reserve TD DTDet Logic high indicates the presence of a double-talk condition. Reserve Reserved bit. Reserve Reserve TDG Reserved bit. Reserved bit. Tone detection status bit gated with the AutoTD bit. (Control Register 2) Logic high indicates that AutoTD has been enabled and the tone detector has detected the presence of a 2100Hz tone. Logic high indicates the presence of a narrow-band signal on Rin. NB Reserved bit. Logic high indicates the presence of a 2100Hz tone. Power-up 00hex Bit 7 FD7 Bit 6 FD6 Bit 5 FD5 Power-up 00 hex Bit 7 NS7 Bit 6 NS6 Power-up 00hex Bit 7 0 Bit 6 0 ECA: Flat Delay Register (FD) R/W Address: 04 hex + Base Address ECB: Flat Delay Register (FD) R/W Address: 24 hex + Base Address Bit 4 FD4 Bit 3 FD3 Bit 2 FD2 Bit 1 FD1 Bit 0 FD0 ECA: Decay Step Size Register (NS) R/W Address: 07hex + Base Address ECB: Decay Step Size Register (NS) R/W Address: 27hex+ Base Address Bit 5 NS5 Bit 4 NS4 Bit 3 NS3 Bit 2 NS2 Bit 1 NS1 Bit 0 NS0 ECA: Decay Step Size Control Register (NS) R/W Address: 06 hex + Base Address ECB: Decay Step Size Control Register (NS) R/W Address: 26 hex + Base Address Bit 5 0 Bit 4 0 Bit 3 0 Bit 2 SSC2 Bit 1 SSC1 Bit 0 SSC0 Note: Bits marked with “0” are reserved bits and should be written “0” Zarlink Semiconductor Inc. 21 ZL50233 Data Sheet Amplitude of MU FIR Filter Length (512 or 1024 taps) 1.0 Step Size (SS) Flat Delay (FD7-0) 2-16 Time Number of Steps (NS7-0) Figure 11 - The MU Profile 9.0 Functional Description of Register Bits The Exponential Decay registers (Decay Step Number and Decay Step Size) and Flat Delay register allow the LMS adaptation step-size (MU) to be programmed over the length of the FIR filter. A programmable MU profile allows the performance of the echo canceller to be optimized for specific applications. For example, if the characteristic of the echo response is known to have a flat delay of several milliseconds and a roughly exponential decay of the echo impulse response, then the MU profile can be programmed to approximate this expected impulse response thereby improving the convergence characteristics of the Adaptive Filter. Note that in the following register descriptions, one tap is equivalent to 125µs (64ms/512 taps). FD7-0 Flat Delay: This register defines the flat delay of the MU profile, (i.e., where the MU value is 2-16). The delay is defined as FD7-0 x 8 taps. For example; If FD7-0 = 5, then MU=2-16 for the first 40 taps of the echo canceller FIR filter. The valid range of FD7-0 is: 0 ≤ FD7-0 ≤ 64 in normal mode and 0 ≤ FD7-0 ≤ 128 in extended-delay mode. The default value of FD7-0 is zero. SSC2-0 Decay Step Size Control: This register controls the step size (SS) to be used during the exponential decay of MU. The decay rate is defined as a decrease of MU by a factor of 2 every SS taps of the FIR filter, where SS = 4 x2SSC2-0. For example; If SSC2-0 = 4, then MU is reduced by a factor of 2 every 64 taps of the FIR filter. The default value of SSC2-0 is 04hex. NS7-0 Decay Step Number: This register defines the number of steps to be used for the decay of MU where each step has a period of SS taps (see SSC2-0). The start of the exponential decay is defined as: Filter Length (512 or 1024) - [Decay Step Number (NS7-0 ) x Step Size (SS)] where SS = 4 x2SSC2-0. For example; If NS7-0 =4 and SSC2-0=4, then the exponential decay start value is 512 - [NS7-0 x SS] = 512 - [4 x (4x24)] = 256 taps for a filter length of 512 taps. 22 Zarlink Semiconductor Inc. ZL50233 Data Sheet Power-up FBhex Bit 7 NLRun2 NLRun2 InjCtrl NLRun1 ECA: Control Register 3 R/W Address: 08 hex + Base Address ECB: Control Register 3 R/W Address: 28 hex + Base Address Bit 6 InjCtrl Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 NLRun1 RingClr Reserve PathClr PathDet NLPSel Functional Description of Register Bits When high, the comfort noise level estimator actively rejects double-talk as being background noise. When low, the noise level estimator makes no such distinction. Selects which noise ramping scheme is used. See Table below. When high, the comfort noise level estimator actively rejects uncancelled echo as being background noise. When low, the noise level estimator makes no such distinction. RingClr When high, the instability detector is activated. When low, the instability detector is disabled. Reserve PathClr Reserved bit. Must always be set to one for normal operation. When high, the current echo channel estimate will be cleared and the echo canceller will enter fast convergence mode upon detection of a path change. When low, the echo canceller will keep the current path estimate but revert to fast convergence mode upon detection of a path change. Note: this bit is ignored if PathDet is low. When high, the path change detector is activated. When low, the path change detector is disabled. When high, the Advanced NLP is selected. When low, the original NLP is selected. See Table 1 on page 9. PathDet NLPSel Power-up 54 hex Bit 7 0 0 SupDec 0 Slow ECA: Control Register 4 R/W Address: 09hex + Base Address ECB: Control Register 4 R/W Address: 29hex + Base Address Bit 6 SD2 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SD1 SD0 0 Slow2 Slow1 Slow0 Functional Description of Register Bits Must be set to zero. These three bits (SD2,SD1,SD0) control how long the echo canceller remains in a fast convergence state following a path change, Reset or Bypass operation. A value of zero will keep the echo canceller in fast convergence indefinitely. Must be set to zero. Slow convergence mode speed adjustment.(Bits Slow2, Slow1,Slow0) For Slow = 1, 2, ..., 7, slow convergence speed is reduced by a factor of 2Slow as compared to normal adaptation. Flow Slow = 0, no adaptation occurs during slow convergence. Zarlink Semiconductor Inc. 23 ZL50233 Data Sheet Power-up 16hex Bit 7 NS7 Bit 6 NS6 ECA: Noise Scaling (NS) R/W Address: 0Ahex + Base Address ECB: Noise Scaling (NS) R/W Address: 2Ahex + Base Address Bit 5 NS5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 NS4 NS3 NS2 NS1 NS0 Functional Description of Register Bits This register is used to scale the comfort noise up or down. Larger values will increase the relative level of comfort noise. The default value of 16hex will provide G.168 compliance with the Advanced NLP. A value of 74hex is recommended if the original NLP is used. Power-up 45hex Bit 7 Reserve Reserve NLInc R/W Address: 0Bhex + Base Address ECB: Noise Control R/W Address: 2Bhex + Base Address Bit 6 Reserve Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reserve Reserve NLInc3 NLInc2 NLInc1 NLInc0 Functional Description of Register Bits Reserved bits. Must be set to 4hex for normal operation. Noise level estimator ramping rate. When InjCtrl = 1, a lower value will give faster ramping. When InjCtrl = 0, a higher value will give faster ramping. The default value of 5hex will provide G.168 compliance with InjCtrl = 1. A value of Chex is recommended if InjCtrl = 0. Power-up N/A Bit 7 RP15 ECA: Noise Control Bit 6 RP14 Power-up N/A ECA: Rin Peak Detect Register 2 (RP) R/W Address: 0Dhex + Base Address ECB: Rin Peak Detect Register 2 (RP) R/W Address: 2Dhex + Base Address Bit 5 RP13 Bit 4 RP12 Bit 3 RP11 Bit 2 RP10 ECA: Rin Peak Detect Register 1 (RP) ECB: Rin Peak Detect Register 1 (RP) Bit 7 RP7 Bit 5 RP5 Bit 0 RP8 R/W Address: 0Chex + Base Address R/W Address: 2Chex + Base Address Bit 1 Bit 0 RP1 RP0 Bit 4 Bit 3 Bit 2 RP4 RP3 RP2 Functional Description of Register Bits These peak detector registers allow the user to monitor the receive in (Rin) peak signal level. The information is in 16-bit 2’s complement linear coded format presented in two 8 bit registers for each echo canceller. The high byte is in Register 2 and the low byte is in Register 1. 24 Bit 6 RP6 Bit 1 RP9 Zarlink Semiconductor Inc. ZL50233 Data Sheet Power-up N/A Bit 7 SP15 Bit 6 SP14 ECA: Sin Peak Detect Register 2 (SP) R/W Address: 0Fhex + Base Address ECB: Sin Peak Detect Register 2 (SP) R/W Address: 2Fhex + Base Address Bit 5 SP13 Power-up N/A Bit 4 SP12 Bit 3 SP11 Bit 2 SP10 ECA: Sin Peak Detect Register 1 (SP) ECB: Sin Peak Detect Register 1 (SP) Bit 7 SP7 Bit 6 SP6 Bit 0 SP8 R/W Address: 0Ehex + Base Address R/W Address: 2Ehex + Base Address Bit 1 Bit 0 SP1 SP0 Bit 4 Bit 3 Bit 2 SP4 SP3 SP2 Functional Description of Register Bits These peak detector registers allow the user to monitor the send in (Sin) peak signal level. The information is in 16-bit 2’s complement linear coded format presented in two 8 bit registers for each echo canceller. The high byte is in Register 2 and the low byte is in Register 1. Power-up N/A Bit 7 EP15 Bit 6 EP14 Power-up N/A Bit 7 EP7 Bit 6 EP6 Bit 5 SP5 Bit 1 SP9 ECA: Error Peak Detect Register 2 (EP) R/W Address: 11hex + Base Address ECB: Error Peak Detect Register 2 (EP) R/W Address: 31hex + Base Address Bit 5 EP13 Bit 4 EP12 Bit 3 EP11 Bit 2 EP10 Bit 1 EP9 Bit 0 EP8 ECA: Error Peak Detect Register 1 (EP) R/W Address: 10hex + Base Address ECB: Error Peak Detect Register 1 (EP) R/W Address: 30hex + Base Address Bit 5 EP5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 EP4 EP3 EP2 EP1 EP0 Functional Description of Register Bits These peak detector registers allow the user to monitor the error signal peak level. The information is in 16-bit 2’s complement linear coded format presented in two 8 bit registers for each echo canceller. The high byte is in Register 2 and the low byte is in Register 1. Zarlink Semiconductor Inc. 25 ZL50233 Data Sheet Power-up 48hex Bit 7 DTDT15 Bit 6 DTDT14 Power-up 00hex Bit 7 DTDT7 Bit 6 DTDT6 ECA: Double-Talk Detection Threshold Register 2 R/W Address: 15hex + Base Address ECB: Double-Talk Detection Threshold Register 2 R/W Address: 35hex + Base Address Bit 5 DTDT13 Bit 1 DTDT9 Bit 4 DTDT12 Bit 3 DTDT11 Bit 2 DTDT10 Bit 0 DTDT8 ECA: Double-Talk Detection Threshold Register 1 R/W Address: 14hex + Base Address ECB: Double-Talk Detection Threshold Register 1 R/W Address: 34hex + Base Address Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 DTDT4 DTDT3 DTDT2 DTDT1 DTDT0 Functional Description of Register Bits This register allows the user to program the level of Double-Talk Detection Threshold (DTDT). The 16 bit 2’s complement linear value defaults to 4800hex= 0.5625 or -5 dB. The maximum value is 7FFFhex = 0.9999 or 0 dB. The high byte is in Register 2 and the low byte is in Register 1. Power-up 0Chex Bit 7 NLP15 Bit 6 NLP14 Power-up E0hex Bit 7 NLP7 ECA: Non-Linear Processor Threshold Register 2 (NLPTHR) R/W Address: 19hex + Base Address ECB: Non-Linear Processor Threshold Register 2 (NLPTHR) R/W Address: 39hex + Base Address Bit 5 NLP13 Bit 4 NLP12 Bit 3 NLP11 Bit 2 NLP10 Bit 1 NLP9 Bit 0 NLP8 ECA: Non-Linear Processor Threshold Register 1 (NLPTHR) R/W Address: 18hex + Base Address ECB: Non-Linear Processor Threshold Register 1 (NLPTHR) R/W Address: 38hex + Base Address Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 NLP4 NLP3 NLP2 NLP1 NLP0 Functional Description of Register Bits This register allows the user to program the level of the Non-Linear Processor Threshold (NLPTHR). The 16 bit 2’s complement linear value defaults to 0CE0hex = 0.1 or -20.0dB. The maximum value is 7FFFhex = 0.9999 or 0 dB. The high byte is in Register 2 and the low byte is in Register 1. 26 Bit 6 NLP6 Bit 5 DTDT5 Bit 5 NLP5 Zarlink Semiconductor Inc. ZL50233 Data Sheet Power-up 40hex Bit 7 MU15 Bit 6 MU14 Power-up 00hex Bit 7 MU7 Bit 6 MU6 ECA: Adaptation Step Size Register 2 (MU) R/W Address: 1Bhex + Base Address ECB: Adaptation Step Size Register 2 (MU) R/W Address: 3Bhex + Base Address Bit 5 MU13 Bit 4 MU12 Bit 3 MU11 Bit 2 MU10 Bit 1 MU9 Bit 0 MU8 ECA: Adaptation Step Size Register 1 (MU) R/W Address: 1Ahex + Base Address ECB: Adaptation Step Size Register 1 (MU) R/W Address: 3Ahex + Base Address Bit 5 MU5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 MU4 MU3 MU2 MU1 MU0 Functional Description of Register Bits This register allows the user to program the level of MU. MU is a 16 bit 2’s complement value which defaults to 4000hex = 1.0 The maximum value is 7FFF hex or 1.9999 decimal. The high byte is in Register 2 and the low byte is in Register 1. Power-up 44hex Bit 7 0 Bit 6 Rin2 Bit 5 Rin1 ECB: Gains Register 2 R/W Address: 3Dhex + Base Address Bit 4 Rin0 Bit 3 0 ECB: Gains Register 1 Bit 2 Rout2 Bit 1 Rout1 Bit 0 Rout0 R/W Address: 1Chex + Base Address R/W Address: 3Chex + Base Address Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Sin0 0 Sout2 Sout1 Sout0 Functional Description of Register Bits This register is used to select gain values on RIN, ROUT, SIN and SOUT. Gains has the following structure: RIN ROUT SIN SOUT Gains = 0xxx 0xxx 0xxx 0xxx = 0100 0100 0100 0100 (4444hex) default Gains is split into four groups of four bits. Each group maps to a different signal port (as indicated above), and has three gain bits. The following table indicates how these gain bits are used: Bit2 1 0 0 0 0 Bit1 Bit0 0 0 1 1 1 0 0 1 0 0 Bit 6 Sin2 R/W Address: 1Dhex + Base Address ECA: Gains Register 1 Power-up 44hex Bit 7 0 ECA: Gains Register 2 Bit 5 Sin1 Gain Level 0 dB (default) -3 dB -6 dB -9 dB -12 dB Note that the -12 dB PAD bit in Control Register 1 provides 12 dB of attenuation in the Rin to Rout path, and will override the settings in Gains. Zarlink Semiconductor Inc. 27 ZL50233 Data Sheet Main Control Register 0 (EC Group 0) Power-up 00hex Bit 7 WR_all WR_all ODE MIRQ Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 MIRQ MTDBI MTDAI Format Law PWUP Functional Description of Register Bits Write all control bit: When high, Group 0 and 1 Echo Cancellers Registers are mapped into 0000hex to 0003Fhex which is Group 0 address mapping. Useful to initialize the 2 Groups of Echo Cancellers as per Group 0. When low, address mapping is per Figure 10. Note: Only the Main Control Register 0 has the WR_all bit Output Data Enable: This control bit is logically AND’d with the ODE input pin. When both ODE bit and ODE input pin are high, the Rout and Sout outputs are enabled. When the ODE bit is low or the ODE input pin is low, the Rout and Sout outputs are high impedance. Note: Only the Main Control Register 0 has the ODE bit. Mask Interrupt: When high, all the interrupts from the Tone Detectors output are masked. The Tone Detectors operate as specified in their Echo Canceller B, Control Register 2. When low, the Tone Detectors Interrupts are active. Note: Only the Main Control Register 0 has the MIRQ bit. MTDBI Mask Tone Detector B Interrupt: When high, the Tone Detector interrupt output from Echo Canceller B is masked. The Tone Detector operates as specified in Echo Canceller B, Control Register 2. When low, the Tone Detector B Interrupt is active. MTDAI Mask Tone Detector A Interrupt: When high, the Tone Detector interrupt output from Echo Canceller A is masked. The Tone Detector operates as specified in Echo Canceller A, Control Register 2. When low, the Tone Detector A Interrupt is active. Format ITU-T/Sign Mag: When high, both Echo Cancellers A and B for a given group, accept ITU-T (G.711) PCM code. When low, both Echo Cancellers A and B for a given group, accept signmagnitude PCM code. Law PWUP 28 R/W Address: 400hex Bit 6 ODE A/µ Law: When high, both Echo Cancellers A and B for a given group, accept A-Law companded PCM code. When low, both Echo Cancellers A and B for a given group, accept µ-Law companded PCM code. Power-UP: When high, both Echo Cancellers A and B and Tone Detectors for a given group, are active. When low, both Echo Cancellers A and B and Tone Detectors for a given group, are placed in Power Down mode. In this mode, the corresponding PCM data are bypassed from Rin to Rout and from Sin to Sout with two frames delay. When the PWUP bit toggles from zero to one, the echo canceller A and B execute their initialization routine which presets their registers, Base Address+00hex to Base Address+3Fhex, to default power up value and clears the Adaptive Filter coefficients. Two frames are necessary for the initialization routine to execute properly. Once the initialization routine is executed, the user can set the per channel Control Registers for their specific application. Zarlink Semiconductor Inc. ZL50233 Data Sheet Bit 7 Unused Unused MTDBI MTDAI Format Law PWUP Main Control Register 1 (EC Group 1) R/W Address: 401hex Power-up 00hex Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Unused Unused MTDBI MTDAI Format Law PWUP Functional Description of Register Bits Unused Bits. Mask Tone Detector B Interrupt: When high, the Tone Detector interrupt output from Echo Canceller B is masked. The Tone Detector operates as specified in Echo Canceller B, Control Register 2. When low, the Tone Detector B Interrupt is active. Mask Tone Detector A Interrupt: When high, the Tone Detector interrupt output from Echo Canceller A is masked. The Tone Detector operates as specified in Echo Canceller A, Control Register 2. When low, the Tone Detector A Interrupt is active. ITU-T/Sign Mag: When high, both Echo Cancellers A and B for a given group, select ITU-T (G.711) PCM code. When low, both Echo Cancellers A and B for a given group, select sign-magnitude PCM code . A/µ Law: When high, both Echo Cancellers A and B for a given group, select A-Law companded PCM code. When low, both Echo Cancellers A and B for a given group, select µ-Law companded PCM code. Power-UP: When high, both Echo Cancellers A and B and Tone Detectors for a given group, are active. When low, both Echo Cancellers A and B and Tone Detectors for a given group, are placed in Power Down mode. In this mode, the corresponding PCM data are bypassed from Rin to Rout and from Sin to Sout with two frames delay. When the PWUP bit toggles from zero to one, the echo cancellers A and B execute their initialization routine which presets their registers, Base Address+00hex to Base Address+3Fhex, to default Reset Value and clears the Adaptive Filter coefficients. Two frames are necessary for the initialization routine to execute properly. Once the initialization routine is executed, the user can set the per channel Control Registers for their specific application. Interrupt FIFO Register Power-up 00hex Bit 7 IRQ IRQ Unused Unused I<4:0> R/W Address: 410hex Bit 6 Unused Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Unused I4 I3 I2 I1 I0 Functional Description of Register Bits Logic high indicates an interrupt has occurred. IRQ bit is cleared after the Interrupt FIFO register is read. Logic Low indicates that no interrupt is pending and the FIFO is empty. Unused bit. Unused bit. I<4:0> binary code indicates the channel number at which a Tone Detector state change has occurred. Note: Whenever a Tone Disable is detected or released, an interrupt is generated. Zarlink Semiconductor Inc. 29 ZL50233 Data Sheet Absolute Maximum Ratings* Parameter Symbol Min Max Units 1 I/O Supply Voltage (VDD1) VDD_IO -0.5 5.0 V 2 Core Supply Voltage (VDD2) VDD_CORE -0.5 2.5 V 3 Input Voltage VI3 VSS - 0.5 V DD1+0.5 V 4 Input Voltage on any 5V Tolerant I/O pins VI5 VSS - 0.3 7.0 V 5 Continuous Current at digital outputs Io 20 mA 6 Package power dissipation PD 2 W 150 °C 7 Storage temperature TS -55 * Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. . Recommended Operating Conditions - Voltages are with respect to ground (Vss) unless otherwise stated Characteristics 1 Operating Temperature Sym Min TOP -40 Typ‡ Max Units +85 °C 2 I/O Supply Voltage (VDD_IO) VDD1 3.0 3.3 3.6 V 3 Core Supply Voltage (VDD_CORE) VDD2 1.6 1.8 2.0 V 4 Input High Voltage on 3.3V tolerant I/O VIH3 0.7VDD1 VDD1 V 5 Input High Voltage on 5V tolerant I/O pins VIH5 0.7VDD1 5.5 V 6 Input Low Voltage VIL 0.3VDD1 V ‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing DC Electrical Characteristics† - Voltages are with respect to ground (Vss) unless otherwise stated. Characteristics 1 3 4 5 I N P U T S 6 7 8 9 10 Typ‡ Static Supply Current ICC IDD_IO 5 Max 250 Units Test Conditions µA RESET = 0 mA All 4 channels active All 4 channels active IDD_CORE 13 mA Power Consumption PC 40 mW All 4 channels active Input High Voltage VIH Input Low Voltage Input Leakage Input Leakage on Pullup Input Leakage on Pulldown Input Pin Capacitance O U T P U T S Min IDD_IO (VDD1 = 3.3V) IDD_CORE (V DD2 = 1.8V) 2 Sym 0.7VDD1 V VIL 0.3VDD1 V IIH/IIL ILU ILD 10 -55 65 µA µA µA 10 pF -30 30 CI 0.8VDD1 VIN=V SS to VDD1or 5.5V VIN=V SS VIN=V DD1 See Note 1 Output High Voltage VOH V IOH = 12 mA Output Low Voltage VOL 0.4 V IOL = 12 mA High Impedance Leakage IOZ 10 µA VIN=V SS to 5.5V Output Pin Capacitance CO 10 pF † Characteristics are over recommended operating conditions unless otherwise stated ‡ Typical figures are at 25°C, VDD1 =3.3V and are for design aid only: not guaranteed and not subject to production testing. * Note 1: Maximum leakage on pins (output or I/O pins in high impedance state) is over an applied voltage (VIN). 30 Zarlink Semiconductor Inc. ZL50233 Data Sheet AC Electrical Characteristics† - Timing Parameter Measurement Voltage Levels - Voltages are with respect to ground (Vss) unless otherwise stated. Characteristics Sym Level Units 1 CMOS Threshold VTT 0.5V DD1 V 2 CMOS Rise/Fall Threshold Voltage High VHM 0.7V DD1 V 3 CMOS Rise/Fall Threshold Voltage Low VLM 0.3V DD1 V Conditions † Characteristics are over recommended operating conditions unless otherwise stated AC Electrical Characteristics† - Frame Pulse and C4i Characteristic 1 Frame pulse width (ST-BUS, GCI) Sym Min tFPW 20 Typ‡ Max Units 2* ns Notes tCP-20 2 Frame Pulse Setup time before C4i falling (ST-BUS or GCI) tFPS 10 122 150 ns 3 Frame Pulse Hold Time from C4i falling (ST-BUS or GCI) tFPH 10 122 150 ns 4 C4i Period tCP 190 244 300 ns 5 C4i Pulse Width High tCH 85 150 ns 6 C4i Pulse Width Low tCL 85 150 ns 7 C4i Rise/Fall Time tr, tf 10 ns † Characteristics are over recommended operating conditions unless otherwise stated ‡ Typical figures are at 25°C, V DD1 = 3.3V and for design aid only: not guaranteed and not subject to production testing AC Electrical Characteristics† - Serial Streams for ST-BUS and GCI Backplanes Characteristic Sym Min Typ‡ Max Units Test Conditions 1 Rin/Sin Set-up Time tSIS 10 ns 2 Rin/Sin Hold Time tSIH 10 ns 3 Rout/Sout Delay - Active to Active tSOD 60 ns CL=150pF 4 Output Data Enable (ODE) Delay tODE 30 ns CL=150pF, RL=1K See Note 1 † Characteristics are over recommended operating conditions unless otherwise stated ‡ Typical figures are at 25°C, V DD1 = 3.3V and for design aid only: not guaranteed and not subject to production testing * Note1: High Impedance is measured by pulling to the appropriate rail with RL, with timing corrected to cancel time taken to discharge CL. Zarlink Semiconductor Inc. 31 ZL50233 Data Sheet AC Electrical Characteristics† - Master Clock - Voltages are with respect to ground (VSS). unless otherwise stated. Characteristic Sym Min Typ ‡ Max Units 1 Master Clock Frequency, - Fsel = 0 - Fsel = 1 fMCF0 fMCF1 19.0 9.5 20.0 10.0 21.0 10.5 MHz MHz 2 Master Clock Low tMCL 20 ns 3 Master Clock High tMCH 20 ns Notes † Characteristics are over recommended operating conditions unless otherwise stated ‡ Typical figures are at 25°C, VDD1 = 3.3V and for design aid only: not guaranteed and not subject to production testing AC Electrical Characteristics† - Motorola Non-Multiplexed Bus Mode Typ‡ Characteristics Sym Min Max Units 1 CS setup from DS falling tCSS 0 ns 2 R/W setup from DS falling tRWS 0 ns 3 Address setup from DS falling tADS 0 ns 4 CS hold after DS rising tCSH 0 ns 5 R/W hold after DS rising tRWH 0 ns 6 Address hold after DS rising tADH 0 ns 7 Data delay on read tDDR 8 Data hold on read tDHR 3 9 Data setup on write tDSW 0 ns 10 Data hold on write tDHW 0 ns 11 Acknowledgment delay tAKD 12 Acknowledgment hold time tAKH 13 IRQ delay tIRD 79 ns 15 ns 80 ns 0 8 ns 20 65 ns Test Conditions † Characteristics are over recommended operating conditions unless otherwise stated ‡ Typical figures are at 25°C, VDD1 = 3.3V and for design aid only: not guaranteed and not subject to production testing 32 Zarlink Semiconductor Inc. ZL50233 Data Sheet tFPW F0i VTT tFPS tCP tFPH tCH tr tCL VHM VTT VLM C4i tSOD Rout/Sout tf Bit 7, Channel 0 tSIS Rin/Sin Bit 6, Channel 0 VTT Bit 5, Channel 0 tSIH Bit 7, Channel 0 Bit 6, Channel 0 VTT Bit 5, Channel 0 Figure 12 - ST-BUS Timing at 2.048 Mb/s tFPW F0i VTT tFPS tCP tFPH tCH tCL tr VHM VTT VLM C4i tSOD Sout/Rout tf Bit 0, Channel 0 tSIS Sin/Rin Bit 1, Channel 0 Bit 2, Channel 0 VTT tSIH Bit 0, Channel 0 Bit 1, Channel 0 Bit 2, Channel 0 VTT Figure 13 - GCI Interface Timing at 2.048 Mb/s VTT ODE tODE Sout/Rout HiZ tODE Valid Data HiZ VTT Figure 14 - Output Driver Enable (ODE) Zarlink Semiconductor Inc. 33 ZL50233 Data Sheet tMCH VTT MCLK tMCL Figure 15 - Master Clock VTT DS tCSS tCSH VTT CS tRWH tRWS VTT R/W tADS tADH VTT VALID ADDRESS A0-A10 tDDR tDHR VTT VALID READ DATA D0-D7 READ tDSW tDHW VTT VALID WRITE DATA D0-D7 WRITE tAKD tAKH VTT DTA tIRD VTT IRQ Figure 16 - Motorola Non-Multiplexed Bus Timing 34 Zarlink Semiconductor Inc. For more information about all Zarlink products visit our Web Site at www.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. trading as Zarlink Semiconductor or its subsidiaries (collectively “Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request. Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in an I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 2003, Zarlink Semiconductor Inc. All Rights Reserved. TECHNICAL DOCUMENTATION - NOT FOR RESALE