DIODES ZXLD1615

ZXLD1615
ADJUSTABLE DC-DC BOOST CONVERTER WITH INTERNAL SWITCH IN
TSOT23-5
DESCRIPTION
The ZXLD1615 is a PFM inductive boost converter
designed to provide output voltages of up to 28V
from a 2.5V to 5.5V input supply.
The ZXLD1615 includes the output switch and peak
current sense resistor, and can provide up to 10mA
output current at maximum output voltage. Higher
current is available at lower output voltages.
Nominal output voltage can be set up to a maximum
of 28V by two external resistors and can be adjusted
to lower values by a PWM control signal applied to
the 'Enable' pin. Depending upon the control
frequency, the PWM signal will provide either
continuous (low ripple) or gated control. The PWM
filter components are contained within the chip.
Minimum output voltage is determined by the input
supply.
The device is assembled in a low profile TSOT23-5
pin package.
Quiescent current is typically 60␮A and a shutdown
function is provided to reduce this current to less
than 100nA in the 'off' state.
ADVANCED FEATURES
• Internal 30V NDMOS switch
APPLICATIONS
• True analog output voltage control via PWM
• LCD and OLED bias
with internal filter
• Cellular / mobile phones
FEATURES
• Digital cameras
• Low profile TSOT23-5 pin package
• PDAs
• Internal PWM filter for adjustable output
• LCD modules
• High efficiency (85% typ)
• Varactor and PIN diode bias
• Wide input voltage range: 2.5V to 5.5V
• Palmtop computers
• Up to 250mA output current at 5V
• Low quiescent current: (60␮A typ)
TYPICAL APPLICATION CIRCUIT
• 100nA maximum shutdown current
• Up to 1MHz switching frequency
• Low external component count
PINOUT
TOP VIEW
ISSUE 3 - AUGUST 2004
1
SEMICONDUCTORS
ZXLD1615
ABSOLUTE MAXIMUM RATINGS
(Voltages to GND unless otherwise stated)
Input voltage (VIN)
7V
LX output voltage (VLX)
Switch output current (ILX)
Power dissipation (PD)
30V
500mA
300mW
Operating temperature (TOP)
-40 to 85°C
Storage temperature (TST)
-55 to 150°C
Junction temperature (Tj MAX)
125°C
ELECTRICAL CHARACTERISTICS: (Test conditions: VIN=VEN=3V, TAMB=25°C unless otherwise stated(1))
Symbol
Parameter
V IN
Input voltage
I IN
Supply current
Conditions
Min
Typ
2.5
Quiescent
VEN = VIN, ILX = 0, Output not switching
Shutdown
V EN = 0V
60
<10
V FB
FB pin control voltage
0.98
f LX
Operating frequency
T OFF
LX output ‘OFF’ time
T ON (2)
LX output ‘ON’ time
I LXpk
Switch peak current limit
R LX
Switch 'On' resistance
I LX(leak)
Switch leakage current
V ENH
EN pin high level Input voltage Device active
V ENL
EN pin low level Input voltage
Device in shutdown
I ENL
EN pin low level input current
V EN =0V
I ENH
EN pin high level input current V EN =V IN
L=10␮H, V OUT =28V, 5mA load
Max
Units
5.5
V
100
µA
100
nA
1.07
V
600
350
kHz
500
ns
5
L=10␮H, V OUT =28V, 5mA load
320
mA
⍀
1.75
V LX =20V
TEN(hold)(3) EN pin turn off delay
V EN switched from high to low
⌬T/T
PWM duty cycle range at
‘EN’ input for dc output
voltage control
10kHz < f < 100kHz, V ENH =V IN
f LPF
Internal PWM low pass filter
cut-off frequency
A LPF
Filter attenuation
f=30kHz
1.5
1
µA
V IN
V
0.4
V
-100
nA
1
␮A
120
20
µs
µs
100
%
4
kHz
52.5
dB
NOTES:
1 Production testing of the device is performed at 25°C. Functional operation of the device over a –40°C to +85°C temperature range is
guaranteed by design, characterization and process control.
2 Nominal ‘on’ time (TONnom ) is defined by the input voltage (VIN), coil inductance (L) and peak current (ILXpkdc) according to the expression:
TONnom = {ILX(pkdc) x L/VIN} +200ns
3 This is the time for which the device remains active after the EN pin has been asserted low. This delay is necessary to allow the output to be
maintained during dc PWM mode operation.
4 The maximum PWM signal frequency during this mode of operation should be kept as low as possible to minimize errors due to the turn-off
delay
ISSUE 3 - AUGUST 2004
SEMICONDUCTORS
2
ZXLD1615
PIN DESCRIPTION
Pin No.
Name
Description
1
LX
Output of NDMOS switch
2
GND
Ground (0V)
3
FB
Feedback pin for voltage control loop
4
EN
Nominal voltage 1.025V
Enable input (active high to turn on device)
Also used to adjust output current by PWM signal.
Connect to V in for permanent operation.
5
V IN
Input voltage (2.5V to 5.5V). Decouple with capacitor close to device.
BLOCK DIAGRAM
ISSUE 3 - AUGUST 2004
3
SEMICONDUCTORS
ZXLD1615
Device Description
The device is a PFM flyback dc-dc boost converter,
working in discontinuous mode.
With reference to the chip block diagram and typical
application circuit, the operation of the device is as
follows:
Filtered PWM operation
The input of an internal low pass filter is switched to
VREF when the EN pin is high and switched to ground
when the EN pin is low. The output of this filter
drives the comparator within the control loop. A
continuous high state on EN therefore provides a
filtered voltage of value Vref to the comparator.
However, by varying the duty cycle of the EN signal
at a suitably high frequency (f>10kHz), the control
loop will see a voltage, that has an average value
equal to the duty cycle multiplied by VREF. This
provides a means of adjusting the output voltage to a
lower value. It also allows the device to be both
turned on and adjusted with a single signal at the
‘EN’ pin. The output during this mode of operation
will be a dc voltage equal to VREF*(R1+R2)/R1 x duty
cycle.
Control loop
When 'EN' is high, the control circuits become active
and the low side of the coil (L1) is switched to ground
via NDMOS transistor (MN). The current in L1 is
allowed to build up to an internally defined level
(nominally 320mA) before MN is turned off. The
energy stored in L1 is then transferred to the output
capacitor (C2) via schottky diode (D1). The output
voltage is sensed at pin 'FB' by external resistors R1
and R2 and compared to a reference voltage VREF
(1.025V nominal). A comparator senses when the
output voltage is above that set by the reference and
its output is used to control the 'off' time of the
output switch. The control loop is self-oscillating,
producing pulses of up to 5␮s maximum duration
(switch 'on'), at a frequency that varies in proportion
to the output current. The feedback loop maintains a
voltage of VREF at the FB pin and therefore defines a
maximum output voltage equal to VREF *(R1+R2)/R1.
The minimum 'off' time of the output switch is fixed
at 0.5␮s nominal, to allow time for the coil's energy
to be dissipated before the switch is turned on again.
This maintains stable and efficient operation in
discontinuous mode.
Gated PWM operation
The internal circuitry of the ZXLD1615 is turned off
when no signal is present on the 'EN' pin for more
than 120␮s (nominal). A low frequency signal applied
to the EN pin will therefore gate the device 'on' and
'off' at the gating frequency and the duty cycle of this
signal can be varied to provide an average output
equal to VREF *(R1+R2)/R1 x duty cycle. For best
accuracy, the gating frequency should be made as
low as possible (e.g. below 1kHz), such that the turn
off delay of the chip is only a small proportion of the
gating period
Further details of setting output current are given in
the application notes.
ISSUE 3 - AUGUST 2004
SEMICONDUCTORS
4
ZXLD1615
TYPICAL CHARACTERISTICS
ISSUE 3 - AUGUST 2004
5
SEMICONDUCTORS
ZXLD1615
TYPICAL PERFORMANCE GRAPHS
(For typical applications circuit at 22␮H Murata LQH32CN series, TA=25 °C unless otherwise stated)
ISSUE 3 - AUGUST 2004
SEMICONDUCTORS
6
ZXLD1615
APPLICATIONS
1) PWM output voltage adjustment (analogue mode)
During this mode of operation the device operation is
continuous, providing a low ripple output voltage
(VOUT) directly proportional to the duty cycle (D) of
the logic signal applied to the EN pin according to the
relationship:
Setting output voltage
The ZXLD1615 has an adjustable output voltage
allowing the end user maximum flexibility. To set the
output voltage a potential divider network is needed
(see R1 and R2 in typical applications circuit).
The output voltage is determined by the equation:
R2 ⎞
⎛
⎟
V OUT = V FB ⎜1 +
⎝
R1⎠
VOUT = D x VOUT(nom)
Square wave signals applied to the EN pin, for
example, will turn the device on and produce a
nominal regulated output of 13.5V.
The ZXLD1615 contains a timing circuit that switches
the device on a few microseconds after the
application of a rising edge to EN and turns it back
off again nominally 120µs after the falling edge of
EN. For continuous PWM mode operation, the
frequency of the control signal must therefore be
maintained above 10kHz at all times, to prevent the
internal delay circuit from timing out and switching
the device into standby mode. The maximum
frequency applied to EN should be limited to 100kHz
to minimize errors due to internal switching delays
where VFB = 1.025V.
The following table gives suggested values for
various output voltages.
Required
R1
output voltage
R2
5V
270K⍀
1M⍀
12V
91K⍀
1M⍀
18V
60K⍀
1M⍀
21V
51K⍀
1M⍀
25V
43K⍀
1M⍀
28V
39K⍀
1M⍀
2) PWM output voltage adjustment (gated mode)
This method of adjustment can be used in
applications where the output ripple is less important
than the supply current. The method of adjustment is
the same as in 1) above, however, during this mode
of operation, the device is gated on and off,
providing an average output voltage (VOUT) directly
proportional to the duty cycle (D) of the logic signal
applied to the EN pin according to the relationship:
Output voltage can be adjusted from VIN + VF to the
maximum output voltage rating of the internal
switch, 30V.
Once the nominal output voltage has been set, it can
be adjusted to a lower value by applying a pulse
width modulated (PWM) control signal to the EN pin.
PWM adjustment permits the device to be turned on
and the output voltage set by a single logic signal
applied to the EN pin. No external resistors are
required and the amplitude of the control signal is
not critical, providing it conforms to the limits
defined in the electrical characteristics.
VOUT(AVG) = D x VOUT(nom)
The ripple on this voltage will be determined by the
size of the output capacitor.
The output voltage can be adjusted all the way down
to the input voltage by either method of PWM
control, but for best results, the duty cycle range
should be kept within the specified range. Lower duty
cycles will result in increased output ripple and
non-linearity in the relationship between duty cycle
and output voltage. If a greater control range is
required, the nominal output can be reduced by the
use of external resistors before the PWM signal is
applied.
Minimizing output voltage ripple
For applications requiring lower output ripple it may
be necessary to add a small ceramic capacitor in
parallel with R2. A value of 4.7pF is suitable for most
output ranges.
ISSUE 3 - AUGUST 2004
7
SEMICONDUCTORS
ZXLD1615
Capacitor selection
A ceramic capacitor grounded close to the GND pin
of the package is recommended at the output of the
device. Surface mount types offer the best
performance due to their lower inductance. A
minimum value of 0.22␮F is advised, although higher
values will lower switching frequency and improve
efficiency especially at lower load currents. A higher
value will also minimize ripple when using the device
to provide an adjustable dc output current.
A good quality, low ESR capacitor should also be
used for input decoupling, as the ESR of this
capacitor is effectively in series with the source
impedance and lowers overall efficiency. This
capacitor has to supply the relatively high peak
current to the coil and smooth the current ripple on
the input supply. A minimum value of 4.7␮F is
acceptable if the input source is close to the device,
but higher values will improve performance at lower
input voltages, when the source impedance is high.
The input capacitor should be mounted as close as
possible to the IC.
For maximum stability over temperature, capacitors
with X7R dielectric are recommended, as these have
a much smaller temperature coefficient than other
types.
A table of recommended manufacturers is provided
below:
Manufacturer
Website
Murata
www.murata.com
Taiyo Yuden
www.t-yuden.com
Kemet
www.kement.com
AVX
www.avxcorp.com
Inductor selection
Recommended inductor values for the ZXLD1615 are
in the range 6.8␮H to 22␮H. The inductor should be
mounted as close to the device as possible with low
resistance connections to the LX and VIN pins.
Suitable coils for use with the ZXLD1615 are shown
in the table below:
The choice of inductor will depend on available
board space as well as required performance. Small
value inductors have the advantage of smaller
physical size and may offer lower series resistance
and higher saturation current compared to larger
values. A disadvantage of lower inductor values is
that they result in higher frequency switching, which
in turn causes reduced efficiency due to switch
losses. Higher inductor values can provide better
performance at lower supply voltages. However, if
the inductance is too high, the output power will be
limited by the internal oscillator, which will prevent
the coil current from reaching its peak value. This
condition will arise whenever the ramp time (ILX(peak)
x L/VIN) exceeds the nominal 5␮s maximum 'on' time
limit for the LX output.
L
DCR
I SAT
( H)
( )
(A)
CMD4D11-100MC
10
0.457
0.5
Sumida
www.sumida.com
DO1608-103
10
0.16
1.1
Coilcraft
www.coilcraft.com
LQH31CN100
10
1.3
0.23
Murata
www.murata.com
LB2012Y100MR
10
0.5
0.1
Taiyo Yuden
www.t-yuden.com
Part No.
Manufacturer
ISSUE 3 - AUGUST 2004
SEMICONDUCTORS
8
ZXLD1615
Diode selection
The rectifier diode (D1) should be a fast low
capacitance schottky diode with low reverse leakage
at the working voltage. It should also have a peak
current rating above the peak coil current and a
continuous current rating higher than the maximum
output load current.
The table below gives some typical characteristics for
diodes that can be used with the ZXLD1615:
Diode
V F @ 100mA (mV)
I FSM (mA)
Ic (mA)
I R at 30V ( A)
Package
ZHCS400
300
1000
400
15
SOD323
ZHCS500
300
1000
500
15
SOT23
Layout considerations
PCB tracks should be kept as short as possible to
minimize ground bounce, and the ground pin of the
device should be soldered directly to the ground
plane. It is particularly important to mount the coil
and the input/output capacitors close to the device to
minimize parasitic resistance and inductance, which
will degrade efficiency. The FB pin is a high
impedance input, so PCB track lengths to this should
also be kept as short as possible to reduce noise
pickup. Excess capacitance from the FB pin to ground
should be avoided.
ISSUE 3 - AUGUST 2004
9
SEMICONDUCTORS
ZXLD1615
REFERENCE DESIGNS
General Boost Converter
VIN=2.5V to 5.5V, VOUT up to 28V
See page 7 in datasheet for R1 and R2 values for various output voltages.
1 Cell Li-Ion to 3.3V Sepic Converter
ISSUE 3 - AUGUST 2004
SEMICONDUCTORS
10
ZXLD1615
1 Cell Li-Ion to 5V Sepic Converter
Triple Output Boost Converter for LCD or OLED Bias
Note: For all manufacturers listing please refer to application section on page 7 of this datasheet.
ISSUE 3 - AUGUST 2004
11
SEMICONDUCTORS
ZXLD1615
PACKAGE DIMENSIONS
PACKAGE OUTLINE
Millimeters
Inches
DIM
MIN.
MAX.
MIN.
MAX.
-
1.00
-
0.0393
A1
0.01
0.10
0.0003
0.0039
A2
0.84
0.90
0.0330
0.0354
b
0.30
0.45
0.0118
0.0177
c
0.12
0.20
0.0047
0.0078
A
D
2.90 BSC
0.114 BSC
E
2.80 BSC
0.110 BSC
E1
1.60 BSC
0.062 BSC
e
0.95 BSC
0.037 BSC
e1
1.90 BSC
0.074 BSC
L
L2
Q
0.30
0.50
0.0118
0.25 BSC
4°
12°
0.0196
0.010 BSC
4°
12°
ORDERING INFORMATION
DEVICE
DEVICE DESCRIPTION
TEMPERATURE
RANGE
ZXLD1615ET5
Boost converter in SOT23-5 -40°C to +85°C
PART MARK
TAPING OPTIONS
615
TA, TC
TA reels 3,000 devices, TC reels 10,000 devices
© Zetex Semiconductors plc 2004
Europe
Americas
Asia Pacific
Corporate Headquarters
Zetex GmbH
Streitfeldstraße 19
D-81673 München
Germany
Zetex Inc
700 Veterans Memorial Hwy
Hauppauge, NY 11788
USA
Zetex (Asia) Ltd
3701-04 Metroplaza Tower 1
Hing Fong Road, Kwai Fong
Hong Kong
Zetex Semiconductors plc
Lansdowne Road, Chadderton
Oldham, OL9 9TY
United Kingdom
Telefon: (49) 89 45 49 49 0
Fax: (49) 89 45 49 49 49
[email protected]
Telephone: (1) 631 360 2222
Fax: (1) 631 360 8222
[email protected]
Telephone: (852) 26100 611
Fax: (852) 24250 494
[email protected]
Telephone (44) 161 622 4444
Fax: (44) 161 622 4446
[email protected]
These offices are supported by agents and distributors in major countries world-wide.
This publication is issued to provide outline information only which (unless agreed by the Company in writing) may not be used, applied or reproduced
for any purpose or form part of any order or contract or be regarded as a representation relating to the products or services concerned. The Company
reserves the right to alter without notice the specification, design, price or conditions of supply of any product or service.
For the latest product information, log on to www.zetex.com
ISSUE 3 - AUGUST 2004
SEMICONDUCTORS
12