ARINC 600 Backshells 527-126 Strain Relief Backshell for Size 3 ARINC 600 Series Connector 527-126 NF P A4 B4 C4 D4 E4 F4 Basic Part No. Finish (Table II) Connector Designator (Table III) Position and Dash No. (Table I) Omit Unwanted Positions Position E Position C 1.50 Thread Size (38.1) (M38999 A Interface) Position F Position D 5.61 (142.5) Position B .50 A Position A 3.25 (82.6) Cable Range (Typ) (12.7) Ref. Jam Nut (Typ) View A-A A Metric dimensions (mm) are indicated in parentheses. © 2004 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] F-20 ARINC 600 Backshells 527-126 Strain Relief Backshell for Size 3 ARINC 600 Series Connector TABLE I: CABLE ENTRY Dash Shell Size A No. Ref. Ref. 3 13 .790 (20.1) 4 15 .790 (20.1) 5 17 .915 (23.2) 6 19 1.165 (29.6) Thread Size M18 X 1.0 M22 X 1.0 M25 X 1.0 M28 X 1.0 Cable Min .190 (4.8) .260 (6.6) .283 (7.2) .325 (8.3) Range Max .328 (8.3) .457 (11.6) .614 (15.6) .634 (16.1) TABLE II: FINISH OPTIONS Symbol B C* G* J LF M N Finish Symbol Finish Cadmium Plate/Olive Drab NC Zinc Cobalt/Dark Olive Drab Black Anodize NF Cadmium Plate/Olive Drab over Anodic Hard Coat Electroless Nickel Gold Iridite over Cadmium Plate T Cadmium Plate/Bright over over Electroless Nickel Electroless Nickel U** Cadmium Plate/Bright over Cadmium Plate/Black Electroless Nickel ZN Zinc-Nickel Alloy/Olive Drab *Anodize finish is not suitable for EMI shielding or grounding Electroless Nickel Cadmium Plate/Olive Drab over applications. **Applicable to corrosion resisting steel backshells and Electroless Nickel accessories. Consult factory for other available finishes. TABLE III: CONNECTOR DESIGNATOR ARINC 600 series connector backshells are designed to replace the insert retainer plates. Due to non-standard modifications by the connector manufacturer, the backshell may require special design alterations to mate properly. The following should be used to determine if a backshell modification is required. Prior to ordering, consult factory with connector part numbers not shown to ensure a proper fit. Connector Designator Connector Description P All Manufacturer’s Plug and Receptacle Shells, Except for Those Listed Below (Prior to ordering, consult factory with connector part numbers not listed below to ensure a proper fit.) P1 Cannon BKAD****322 Series Plug P2 Cannon BKAC & BKAE Series Environmental Plug P3 Cannon/Boeing BACC66 Plug P5 Radiall/Boeing BACC66 Plug 1. Metric dimensions (mm) are indicated in parentheses. 2. Material/Finish: Backshell, Fittings, Nuts, Clamps = Al Alloy/See Table II Hardware = SST/Passivate © 2004 Glenair, Inc. CAGE Code 06324 Printed in U.S.A. GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912 www.glenair.com E-Mail: [email protected] F-21