VISHAY 594D226016B

594D
www.vishay.com
Vishay Sprague
Solid Tantalum Chip Capacitors, TANTAMOUNT®,
Conformal Coated, Maximum CV, Low ESR
FEATURES
• Large capacitance rating range
• Mounting: Surface mount
• Lowest ESR for a surface mount tantalum chip
Available
capacitor
• Terminations: 100 % tin (2) standard; tin/lead
Available
available
• 8 mm, 12 mm tape and reel packaging available per
EIA 481 and reeling per IEC 60286-3.
7" [178 mm] standard. 13" [330 mm] available.
• Case code compatibility with EIA 535BAAC and
CECC 30801
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
Note
* This datasheet provides information about parts that are
RoHS-compliant and/or parts that are non-RoHS-compliant. For
example, parts with lead (Pb) terminations are not RoHS-compliant.
Please see the information/tables in this datasheet for details.
PERFORMANCE CHARACTERISTICS
www.vishay.com/doc?40088
Operating Temperature: - 55 °C to + 125 °C
(above 85 °C, voltage derating is required)
Capacitance Range: 1.0 μF to 1500 μF
Capacitance Tolerance: ± 10 %, ± 20 % standard
Voltage Rating: 4 VDC to 50 VDC
Equivalent Series Resistance: ESR readings measured at
100 kHz, + 25 °C from 3500 m to 30 m
ORDERING INFORMATION
594D
477
X0
004
R
2
T
TYPE
CAPACITANCE
CAPACITANCE
TOLERANCE
DC VOLTAGE RATING
AT + 85 °C
CASE
CODE
TERMINATION
REEL SIZE AND
PACKAGING
This is
expressed in pF.
The first two digits
are the significant
figures. The third
is the number
of zeros to follow.
X0 = ± 20 %
X9 = ± 10 %
This is expressed in V.
To complete the three-digit
block, zeros precede the
voltage rating. A decimal
point is indicated by an “R”
(6R3 = 6.3 V).
See Ratings
and Case
Code table
2 = 100 % tin
4 = Gold plated
8 = Solder plated
(60/40)
Special order
Tape and reel
T = 7" [178 mm] reel
W = 13" [330 mm] reel
Note
• Preferred tolerances and reel sizes are in bold.
We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size.
DIMENSIONS in inches [millimeters]
Tantalum wire
nib identifies
anode (+)
terminal
W
L
MAX.
D
REF.
B
J
MAX.
A
J
MAX.
H
CASE CODE
B
C
D
R
LMAX.
0.157
[4.0]
0.280
[7.1]
0.295
[7.5]
0.283
[7.2]
W
0.110 + 0.012/- 0.016
[2.8 + 0.3/- 0.4]
0.126 ± 0.012
[3.2 ± 0.3]
0.169 + 0.012/- 0.024
[4.3 + 0.3/- 0.6]
0.236 + 0.012/- 0.024
[6.0 + 0.3/- 0.6]
H
0.075 + 0.012/- 0.024
[1.9 + 0.3/- 0.6]
0.098 ± 0.012
[2.5 ± 0.3]
0.110 ± 0.012
[2.8 ± 0.3]
0.138 + 0.012/- 0.016
[3.5 + 0.3/- 0.4]
A
0.031 ± 0.012
[0.8 ± 0.3]
0.051 ± 0.012
[1.3 ± 0.3]
0.051 ± 0.012
[1.3 ± 0.3]
0.051 ± 0.012
[1.3 ± 0.3]
B
0.098 ± 0.016
[2.5 ± 0.4]
0.181 ± 0.024
[4.6 ± 0.6]
0.181 ± 0.024
[4.6 ± 0.6]
0.181 ± 0.024
[4.6 ± 0.6]
DREF.
0.138
[3.5]
0.236
[6.0]
0.252
[6.4]
0.244
[6.2]
JMAX.
0.004
[0.1]
0.004
[0.1]
0.004
[0.1]
0.004
[0.1]
Note
• The anode termination (D less B) will be a minimum of 0.012" [0.3 mm]
Revision: 25-Jun-13
Document Number: 40006
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
594D
www.vishay.com
Vishay Sprague
RATINGS AND CASE CODES
μF
4V
6.3 V
10 V
16 V
20 V
25 V
35 V
1.0
50 V
B
2.2
B
3.3
B
4.7
B
B
C
6.8
B
C
C/D
C
C/D
R
C
D/R
D
R
R
10
B
15
22
33
B
B
47
68
100
B
120
150
D
330
C
390
B
B
B
B/C
B/C
B
B/C
C/D
D/R
C/D
D
D/R
B
B/C
C/D
D
R
C
C
R
R
C/D
D
D
D
R
C/D
C/D/R
D/R
C/D
D/R
R
R
470
C/R
D/R
R
680
D
R
R
1000
1500
B
B/C
B/C
270
B
B
180
220
B
R
R
STANDARD RATINGS
CAPACITANCE
(μF)
CASE CODE
PART NUMBER
MAX. DCL
AT + 25 °C
(μA)
MAX. DF
AT + 25 °C
120 Hz
(%)
MAX. ESR
AT + 25 °C
100 kHz
()
MAX. RIPPLE
100 kHz
IRMS
(A)
0.47
4 VDC AT+ 85 °C, 2.7 VDC AT + 125 °C
33
B
594D336(1)004B(2)(3)
1.30
6
0.380
100
B
594D107(1)004B(2)(3)
4.00
8
0.300
0.53
150
B
594D157(1)004B(2)(3)
6.00
8
0.250
0.58
150
C
594D157(1)004C(2)(3)
6.00
8
0.080
1.17
270
D
594D277(1)004D(2)(3)
10.80
8
0.060
1.58
330
C
594D337(1)004C(2)(3)
13.20
8
0.080
1.17
470
C
594D477(1)004C(2)(3)
18.80
10
0.075
1.21
470
R
594D477(1)004R(2)(3)
18.80
10
0.045
2.36
680
D
594D687(1)004D(2)(3)
27.20
12
0.060
1.58
1500
R
594D158(1)004R(2)(3)
60.00
20
0.030
2.89
6.3 VDC AT + 85 °C, 4 VDC AT + 125 °C
22
B
594D226(1)6R3B(2)(3)
1.40
6
0.380
0.47
68
B
594D686(1)6R3B(2)(3)
4.30
6
0.319
0.52
100
B
594D107(1)6R3B(2)(3)
6.30
8
0.250
0.58
Note
• Part number definitions:
(1) Tolerance: For 10 % tolerance, specify “X9”; for 20 % tolerance, change to “X0”
(2) Termination: For 100 % tin specify “2”, for gold plated specify “4”, for solder plated 60/40 specify “8”
(3) Packaging code: For 7" reels specify “T”, for 13" reels specify “W”.
Revision: 25-Jun-13
Document Number: 40006
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
594D
www.vishay.com
Vishay Sprague
STANDARD RATINGS
CAPACITANCE
(μF)
CASE CODE
120
220
220
330
330
390
470
470
680
1000
C
C
D
C
D
R
D
R
R
R
15
22
33
47
68
68
100
100
120
150
150
180
220
220
220
330
330
470
680
B
B
B
B
B
C
B
C
C
C
D
D
C
D
R
D
R
R
R
15
22
33
33
47
47
68
68
100
100
120
150
180
220
220
330
B
B
B
C
B
C
C
D
C
D
R
D
R
D
R
R
PART NUMBER
MAX. DCL
AT + 25 °C
(μA)
MAX. ESR
AT + 25 °C
100 kHz
()
MAX. RIPPLE
100 kHz
IRMS
(A)
8
8
8
8
8
8
8
10
10
16
0.085
0.080
0.065
0.080
0.060
0.045
0.060
0.050
0.045
0.030
1.14
1.17
1.52
1.17
1.58
2.36
1.58
2.24
2.36
2.89
6
6
6
6
6
6
12
8.0
7.0
8.0
8
7
8
8
8
8
8
8
14
0.500
0.500
0.500
0.400
0.350
0.100
0.250
0.095
0.095
0.090
0.075
0.090
0.100
0.065
0.065
0.065
0.045
0.045
0.045
0.41
0.41
0.41
0.46
0.49
1.05
0.58
1.08
1.08
1.11
1.41
1.29
1.05
1.52
1.96
1.52
2.36
2.36
2.36
6
6
6
6
6
6
6
6
8
8
8
8
8
12
8
14
0.550
0.500
0.500
0.150
0.720
0.110
0.123
0.095
0.080
0.075
0.080
0.085
0.055
0.080
0.055
0.055
0.39
0.41
0.41
0.86
0.34
1.00
0.95
1.26
1.17
1.41
1.77
1.33
2.13
1.37
2.13
2.13
MAX. DF
AT + 25 °C
120 Hz
(%)
6.3 VDC AT + 85 °C, 4 VDC AT + 125 °C
594D127(1)6R3C(2)(3)
7.60
594D227(1)6R3C(2)(3)
13.90
594D227(1)6R3D(2)(3)
13.90
594D337(1)6R3C(2)(3)
20.80
594D337(1)6R3D(2)(3)
20.80
594D397(1)6R3R(2)(3)
24.60
594D477(1)6R3D(2)(3)
29.60
594D477(1)6R3R(2)(3)
29.60
594D687(1)6R3R(2)(3)
42.80
594D108(1)6R3R(2)(3)
63.00
10 VDC AT + 85 °C, 7 VDC AT + 125 °C
594D156(1)010B(2)(3)
1.50
594D226(1)010B(2)(3)
2.20
594D336(1)010B(2)(3)
3.30
594D476(1)010B(2)(3)
4.70
594D686(1)010B(2)(3)
6.80
594D686(1)010C(2)(3)
6.80
594D107(1)010B(2)(3)
10.00
594D107(1)010C(2)(3)
10.00
594D127(1)010C(2)(3)
12.00
594D157(1)010C(2)(3)
15.00
594D157(1)010D(2)(3)
15.00
594D187(1)010D(2)(3)
18.00
594D227(1)010C(2)(3)
22.00
594D227(1)010D(2)(3)
22.00
594D227(1)010R(2)(3)
22.00
594D337(1)010D(2)(3)
33.00
594D337(1)010R(2)(3)
33.00
594D477(1)010R(2)(3)
47.00
594D687(1)010R(2)(3)
68.00
16 VDC AT + 85 °C, 10 VDC AT + 125 °C
594D156(1)016B(2)(3)
2.40
594D226(1)016B(2)(3)
3.50
594D336(1)016B(2)(3)
5.30
594D336(1)016C(2)(3)
5.30
594D476(1)016B(2)(3)
7.50
594D476(1)016C(2)(3)
7.50
594D686(1)016C(2)(3)
10.90
594D686(1)016D(2)(3)
10.90
594D107(1)016C(2)(3)
16.00
594D107(1)016D(2)(3)
16.00
594D127(1)016R(2)(3)
19.20
594D157(1)016D(2)(3)
24.00
594D187(1)016R(2)(3)
28.80
594D227(1)016D(2)(3)
35.20
594D227(1)016R(2)(3)
35.20
594D337(1)016R(2)(3)
52.80
Note
• Part number definitions:
(1) Tolerance: For 10 % tolerance, specify “X9”; for 20 % tolerance, change to “X0”
(2) Termination: For 100 % tin specify “2”, for gold plated specify “4”, for solder plated 60/40 specify “8”
(3) Packaging code: For 7" reels specify “T”, for 13" reels specify “W”.
Revision: 25-Jun-13
Document Number: 40006
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
594D
www.vishay.com
Vishay Sprague
STANDARD RATINGS
MAX. ESR
AT + 25 °C
100 kHz
()
MAX. RIPPLE
100 kHz
IRMS
(A)
6
0.900
0.31
6
0.900
0.31
2.00
6
0.850
0.32
MAX. DCL
AT + 25 °C
(μA)
CAPACITANCE
(μF)
CASE CODE
PART NUMBER
4.7
B
594D475(1)020B(2)(3)
0.90
6.8
B
594D685(1)020B(2)(3)
1.40
10
B
594D106(1)020B(2)(3)
MAX. DF
AT + 25 °C
120 Hz
(%)
20 VDC AT + 85 °C, 13 VDC AT + 125 °C
22
B
594D226(1)020B(2)(3)
4.40
6
0.600
0.38
22
C
594D226(1)020C(2)(3)
4.40
6
0.150
0.86
47
C
594D476(1)020C(2)(3)
9.40
6
0.140
0.89
47
D
594D476(1)020D(2)(3)
9.40
6
0.095
1.26
68
D
594D686(1)020D(2)(3)
13.60
6
0.132
1.07
100
D
594D107(1)020D(2)(3)
20.00
8
0.085
1.33
120
R
594D127(1)020R(2)(3)
24.00
8
0.080
1.77
150
D
594D157(1)020D(2)(3)
30.00
12
0.100
1.22
3.3
B
594D335(1)025B(2)(3)
0.80
6
1.500
0.24
10
B
594D106(1)025B(2)(3)
2.50
6
0.900
0.31
15
C
594D156(1)025C(2)(3)
3.80
6
0.220
0.71
22
C
594D226(1)025C(2)(3)
5.50
6
0.200
0.74
33
D
594D336(1)025D(2)(3)
8.30
6
0.130
1.07
47
D
594D476(1)025D(2)(3)
11.80
6
0.130
1.07
47
R
594D476(1)025R(2)(3)
11.80
6
0.099
1.59
68
D
594D686(1)025D(2)(3)
17.00
8
0.200
0.87
25 VDC AT + 85 °C, 17 VDC AT + 125 °C
68
R
594D686(1)025R(2)(3)
17.00
6
0.095
1.62
100
R
594D107(1)025R(2)(3)
25.00
8
0.090
1.67
2.2
B
594D225(1)035B(2)(3)
0.80
6
1.700
0.22
4.7
B
594D475(1)035B(2)(3)
1.60
6
1.400
0.25
6.8
C
594D685(1)035C(2)(3)
2.40
6
0.430
0.51
15
C
594D156(1)035C(2)(3)
5.30
6
0.400
0.52
15
D
594D156(1)035D(2)(3)
5.30
6
0.270
0.75
22
D
594D226(1)035D(2)(3)
7.70
6
0.270
0.75
22
R
594D226(1)035R(2)(3)
7.70
6
0.220
1.07
33
R
594D336(1)035R(2)(3)
11.60
6
0.200
1.12
47
R
594D476(1)035R(2)(3)
16.60
6
0.200
1.12
35 VDC AT + 85 °C, 23 VDC AT + 125 °C
50 VDC AT + 85 °C, 33 VDC AT + 125 °C
1.0
B
594D105(1)050B(2)(3)
0.50
4
3.500
0.16
4.7
C
594D475(1)050C(2)(3)
2.40
6
0.800
0.37
6.8
C
594D685(1)050C(2)(3)
3.40
6
0.800
0.37
6.8
D
594D685(1)050D(2)(3)
3.40
6
0.450
0.58
15
R
594D156(1)050R(2)(3)
7.50
6
0.350
0.85
Note
• Part number definitions:
(1) Tolerance: For 10 % tolerance, specify “X9”; for 20 % tolerance, change to “X0”
(2) Termination: For 100 % tin specify “2”, for gold plated specify “4”, for solder plated 60/40 specify “8”
(3) Packaging code: For 7" reels specify “T”, for 13" reels specify “W”.
Revision: 25-Jun-13
Document Number: 40006
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
594D
www.vishay.com
Vishay Sprague
RECOMMENDED VOLTAGE DERATING GUIDELINES (for temperature below + 85 °C)
STANDARD CONDITIONS. FOR EXAMPLE: OUTPUT FILTERS
Capacitor Voltage Rating
4.0
6.3
10
16
20
25
35
50
SEVERE CONDITIONS. FOR EXAMPLE: INPUT FILTERS
Capacitor Voltage Rating
4.0
6.3
10
16
20
25
35
50
Operating Voltage
2.5
3.6
6.0
10
12
15
24
28
Operating Voltage
2.5
3.3
5.0
8.0
10
12
15
24
TYPICAL CURVES AT + 25 °C; IMPEDANCE AND ESR VS. FREQUENCY
“C” Case
“B” Case
1000
1000
IMPEDANCE
IMPEDANCE
100
ESR
100
ESR


10
10 2.2 μF, 35 VDC
10 μF, 25 VDC
1.0
1
100 μ F, 6.3 VDC
0.1
22 μF, 6.3 VDC
0.1
100
1K
10K
100K
FREQUENCY IN Hz
1M
10M
0.01
100
1K
“D” Case
10K
100K
FREQUENCY IN Hz
1M
10M
“R” Case
100
100
IMPEDANCE
10
IMPEDANCE
10


ESR
1.0
ESR
1.0
22 μF, 25 VDC
0.1
0.1
0.01
100
1K
Revision: 25-Jun-13
33 μF, 35 VDC
390 μF, 6.3 VDC
220 μF, 6.3 VDC
10K
100K
FREQUENCY IN Hz
1M
10M
0.01
100
1K
10K
100K
FREQUENCY IN Hz
1M
10M
Document Number: 40006
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
594D
www.vishay.com
Vishay Sprague
POWER DISSIPATION
CASE CODE
MAXIMUM PERMISSIBLE POWER DISSIPATION AT + 25 °C (W) IN FREE AIR
B
0.085
C
0.110
D
0.150
R
0.250
STANDARD PACKAGING QUANTITY
CASE CODE
UNITS PER REEL
7" REEL
13" REEL
B
2000
8000
C
500
3000
D
500
3000
R
600
n/a
PRODUCT INFORMATION
Conformal Coated Guide
Pad Dimensions
www.vishay.com/doc?40150
Packaging Dimensions
Moisture Sensitivity
www.vishay.com/doc?40135
SELECTOR GUIDES
Solid Tantalum Selector Guide
www.vishay.com/doc?49053
Solid Tantalum Chip Capacitors
www.vishay.com/doc?40091
FAQ
Frequently Asked Questions
Revision: 25-Jun-13
www.vishay.com/doc?40110
Document Number: 40006
6
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Typical Performance Characteristics
www.vishay.com
Vishay Sprague
Typical Performance Characteristics Tantalum Capacitors
CAPACITOR ELECTRICAL PERFORMANCE CHARACTERISTICS
ITEM
PERFORMANCE CHARACTERISTICS
Category temperature range
- 55 °C to + 85 °C (to + 125 °C with voltage derating)
Capacitance tolerance
± 20 %, ± 10 % (at 120 Hz) 2 VRMS (max.) at + 25 °C using a capacitance bridge
Dissipation factor
Limit per Standard Ratings table. Tested via bridge method, at 25 °C, 120 Hz
ESR
Limit per Standard Ratings table. Tested via bridge method, at 25 °C, 100 kHz
Leakage current
After application of rated voltage applied to capacitors for 5 min using a steady source of power with
1 k resistor in series with the capacitor under test, leakage current at 25 °C is not more than 0.01 CV or
0.5 μA, whichever is greater. Note that the leakage current varies with temperature and applied voltage.
See graph below for the appropriate adjustment factor.
Capacitance change by
temperature
For capacitance value > 300 μF
+ 20 % max. (at + 125 °C)
+ 15 % max. (at + 85 °C)
- 15 % max. (at - 55 °C)
+ 12 % max. (at + 125 °C)
+ 10 % max. (at + 85 °C)
- 10 % max. (at - 55 °C)
Reverse voltage
Capacitors are capable of withstanding peak voltages in the reverse direction equal to:
10 % of the DC rating at + 25 °C
5 % of the DC rating at + 85 °C
Vishay does not recommend intentional or repetitive application of reverse voltage
Temperature derating
If capacitors are to be used at temperatures above + 25 °C, the permissible RMS ripple current or voltage
shall be calculated using the derating factors:
1.0 at + 25 °C
0.9 at + 85 °C
0.4 at + 125 °C
Operating temperature
+ 85 °C
+ 125 °C
RATED VOLTAGE
(V)
SURGE VOLTAGE
(V)
RATED VOLTAGE
(V)
SURGE VOLTAGE
(V)
4
5.2
2.7
3.4
6.3
8
4
5
10
13
7
8
16
20
10
12
20
26
13
16
25
32
17
20
35
46
23
28
50
65
33
40
60
33
40
76
42
50
50
(1)
63
Notes
• All information presented in this document reflects typical performance characteristics
(1) Capacitance values 15 μF and higher
Revision: 27-Feb-13
Document Number: 40088
21
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Typical Performance Characteristics
www.vishay.com
Vishay Sprague
TYPICAL LEAKAGE CURRENT FACTOR RANGE
100
+ 125 °C
+ 150 °C
+ 85 °C
Leakage Current Factor
10
+ 55 °C
+ 25 °C
1.0
0 °C
0.1
- 55 °C
0.01
0.001
0
10
20
30
40
50
60
70
80
90
100
Percent of Rated Voltage
Notes
• At + 25 °C, the leakage current shall not exceed the value listed in the Standard Ratings table.
• At + 85 °C, the leakage current shall not exceed 10 times the value listed in the Standard Ratings table.
• At + 125 °C, the leakage current shall not exceed 12 times the value listed in the Standard Ratings table.
CAPACITOR PERFORMANCE CHARACTERISTICS
ITEM
PERFORMANCE CHARACTERISTICS
Surge voltage
Post application of surge voltage (as specified in the table above) in series with a 33  resistor at the rate of 30 s
ON, 30 s OFF, for 1000 successive test cycles at 85 °C, capacitors meet the characteristics requirements listed
below.
Capacitance change
Dissipation factor
Leakage current
Surge current
After subjecting parts in series with a 1  resistor at the rate of 3 s CHARGE, 3 s DISCHARGE, and a cap bank of
100K μF for 3 successive test cycles at 25 °C, capacitors meet the characteristics requirements listed below.
Capacitance change
Dissipation factor
Leakage current
Life test at + 85 °C
Within ± 10 % of initial value
Shall not exceed 125 % of initial value
Capacitors meet the characteristic requirements listed below. After 1000 h application 2/3 of rated voltage at 125 °C.
Capacitance change
for parts with cap.  600 μF
for parts with cap. > 600 μF
Leakage current
Revision: 27-Feb-13
Within ± 10 % of initial value
Initial specified value or less
Initial specified value or less
Capacitors meet the characteristic requirements listed below. After 2000 h application of rated voltage at 85 °C.
Capacitance change
Leakage current
Life test at + 125 °C
Within ± 10 % of initial value
Initial specified value or less
Initial specified value or less
Within ± 10 % of initial value
Within ± 20 % of initial value
Shall not exceed 125 % of initial value
Document Number: 40088
22
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Typical Performance Characteristics
www.vishay.com
Vishay Sprague
CAPACITOR ENVIRONMENTAL CHARACTERISTICS
ITEM
CONDITION
ENVIRONMENTAL CHARACTERISTICS
Humidity tests
At 40 °C/90 % RH 1000 h, no voltage applied.
Capacitance change
Cap.  600 μF
Cap. > 600 μF
Dissipation factor
Temperature cycles
Moisture resistance
Thermal shock
At - 55 °C/+ 125 °C, 30 min each, for 5 cycles.
Within ± 10 % of initial value
Within ± 20 % of initial value
Not to exceed 150 % of initial
+ 25 °C requirement
Capacitance change
Cap.  600 μF
Cap. > 600 μF
Dissipation factor
Leakage current
Within ± 10 % of initial value
Within ± 20 % of initial value
Initial specified value or less
Initial specified value or less
MIL-STD-202, method 106 at rated voltage,
42 cycles.
Capacitance change
Cap.  600 μF
Cap. > 600 μF
Dissipation factor
Leakage current
Within ± 10 % of initial value
Within ± 20 % of initial value
Initial specified value or less
Initial specified value or less
Capacitors are subjected to 5 cycles of the
following:
- 55 °C (+ 0 °C, - 5 °C) for 30 min, then
+ 25 °C (+ 10 °C, - 5 °C) for 5 min, then
+ 125 °C (+ 3 °C, - 0 °C) for 30 min, then
+ 25 °C (+ 10 °C, - 5 °C) for 5 min
Capacitance change
Cap.  600 μF
Cap. > 600 μF
Dissipation factor
Leakage current
Within ± 10 % of initial value
Within ± 20 % of initial value
Initial specified value or less
Initial specified value or less
MECHANICAL PERFORMANCE CHARACTERISTICS
TEST CONDITION
CONDITION
POST TEST PERFORMANCE
Shear test
Apply a pressure load of 5 N for 10 s ± 1 s
horizontally to the center of capacitor side body.
Capacitance change
Dissipation factor
Leakage current
Within ± 10 % of initial value
Initial specified value or less
Initial specified value or less
There shall be no mechanical or visual damage to
capacitors post-conditioning.
Substrate bend
With parts soldered onto substrate test board,
apply force to the test board for a deflection
of 3 mm, for a total of 3 bends at a rate of 1 mm/s.
Capacitance change
Dissipation factor
Leakage current
Within ± 10 % of initial value
Initial specified value or less
Initial specified value or less
Vibration
MIL-STD-202, method 204, condition D, 10 Hz to
2000 Hz, 20 g peak
Capacitance change
Dissipation factor
Leakage current
Within ± 10 % of initial value
Initial specified value or less
Initial specified value or less
There shall be no mechanical or visual damage to
capacitors post-conditioning.
Shock
MIL-STD-202, method 213B shock (specified
pulse), condition I, 100 g peak
Capacitance change
Dissipation factor
Leakage current
Within ± 10 % of initial value
Initial specified value or less
Initial specified value or less
There shall be no mechanical or visual damage to
capacitors post-conditioning.
Resistance to solder heat
Solderability
Resistance to solvents
• Recommended reflow profiles temperatures
and durations are located within the Capacitor
Series Guides
• Pb-free and lead-bearing series caps are
backward and forward compatible
Capacitance change
Dissipation factor
Leakage current
Within ± 10 % of initial value
Initial specified value or less
Initial specified value or less
There shall be no mechanical or visual damage to
capacitors post-conditioning.
MIL-STD-2002, method 208, ANSI/J-STD-002,
test B. Applies only to solder and tin plated
terminations.
Does not apply to gold terminations.
Capacitance change
Dissipation factor
Leakage current
MIL-STD-202, method 215
Capacitance change
Dissipation factor
Leakage current
Within ± 10 % of initial value
Initial specified value or less
Initial specified value or less
There shall be no mechanical or visual damage to
capacitors post-conditioning.
Within ± 10 % of initial value
Initial specified value or less
Initial specified value or less
There shall be no mechanical or visual damage to
capacitors post-conditioning.
Flammability
Revision: 27-Feb-13
Encapsulent materials meet UL 94 V-0 with an
oxygen index of 32 %.
Document Number: 40088
23
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
Guide for Conformal Coated Tantalum Capacitors
INTRODUCTION
Tantalum electrolytic capacitors are the preferred choice in
applications where volumetric efficiency, stable electrical
parameters, high reliability, and long service life are primary
considerations. The stability and resistance to elevated
temperatures of the tantalum/tantalum oxide/manganese
dioxide system make solid tantalum capacitors an
appropriate choice for today's surface mount assembly
technology.
Vishay Sprague has been a pioneer and leader in this field,
producing a large variety of tantalum capacitor types for
consumer, industrial, automotive, military, and aerospace
electronic applications.
Tantalum is not found in its pure state. Rather, it is
commonly found in a number of oxide minerals, often in
combination with Columbium ore. This combination is
known as “tantalite” when its contents are more than
one-half tantalum. Important sources of tantalite include
Australia, Brazil, Canada, China, and several African
countries. Synthetic tantalite concentrates produced from
tin slags in Thailand, Malaysia, and Brazil are also a
significant raw material for tantalum production.
Electronic applications, and particularly capacitors,
consume the largest share of world tantalum production.
Other important applications for tantalum include cutting
tools (tantalum carbide), high temperature super alloys,
chemical processing equipment, medical implants, and
military ordnance.
Vishay Sprague is a major user of tantalum materials in the
form of powder and wire for capacitor elements and rod and
sheet for high temperature vacuum processing.
THE BASICS OF TANTALUM CAPACITORS
Most metals form crystalline oxides which are
non-protecting, such as rust on iron or black oxide on
copper. A few metals form dense, stable, tightly adhering,
electrically insulating oxides. These are the so-called “valve”
metals and include titanium, zirconium, niobium, tantalum,
hafnium, and aluminum. Only a few of these permit the
accurate control of oxide thickness by electrochemical
means. Of these, the most valuable for the electronics
industry are aluminum and tantalum.
Capacitors are basic to all kinds of electrical equipment,
from radios and television sets to missile controls and
automobile ignitions. Their function is to store an electrical
charge for later use.
Capacitors consist of two conducting surfaces, usually
metal plates, whose function is to conduct electricity. They
are separated by an insulating material or dielectric. The
dielectric used in all tantalum electrolytic capacitors is
tantalum pentoxide.
Tantalum pentoxide compound possesses high-dielectric
strength and a high-dielectric constant. As capacitors are
being manufactured, a film of tantalum pentoxide is applied
to their electrodes by means of an electrolytic process. The
film is applied in various thicknesses and at various voltages
and although transparent to begin with, it takes on different
colors as light refracts through it. This coloring occurs on the
tantalum electrodes of all types of tantalum capacitors.
Revision: 23-Jul-13
Rating for rating, tantalum capacitors tend to have as much
as three times better capacitance/volume efficiency than
aluminum electrolytic capacitors. An approximation of the
capacitance/volume efficiency of other types of capacitors
may be inferred from the following table, which shows the
dielectric constant ranges of the various materials used in
each type. Note that tantalum pentoxide has a dielectric
constant of 26, some three times greater than that of
aluminum oxide. This, in addition to the fact that extremely
thin films can be deposited during the electrolytic process
mentioned earlier, makes the tantalum capacitor extremely
efficient with respect to the number of microfarads available
per unit volume. The capacitance of any capacitor is
determined by the surface area of the two conducting
plates, the distance between the plates, and the dielectric
constant of the insulating material between the plates.
COMPARISON OF CAPACITOR
DIELECTRIC CONSTANTS
DIELECTRIC
Air or vacuum
e
DIELECTRIC CONSTANT
1.0
Paper
2.0 to 6.0
Plastic
2.1 to 6.0
Mineral oil
2.2 to 2.3
Silicone oil
2.7 to 2.8
Quartz
3.8 to 4.4
Glass
4.8 to 8.0
Porcelain
5.1 to 5.9
Mica
5.4 to 8.7
Aluminum oxide
8.4
Tantalum pentoxide
26
Ceramic
12 to 400K
In the tantalum electrolytic capacitor, the distance between
the plates is very small since it is only the thickness of the
tantalum pentoxide film. As the dielectric constant of the
tantalum pentoxide is high, the capacitance of a tantalum
capacitor is high if the area of the plates is large:
eA
C = ------t
where
C = Capacitance
e = Dielectric constant
A = Surface area of the dielectric
t = Thickness of the dielectric
Tantalum capacitors contain either liquid or solid
electrolytes. In solid electrolyte capacitors, a dry material
(manganese dioxide) forms the cathode plate. A tantalum
lead is embedded in or welded to the pellet, which is in turn
connected to a termination or lead wire. The drawings show
the construction details of the surface mount types of
tantalum capacitors shown in this catalog.
Document Number: 40150
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
SOLID ELECTROLYTE TANTALUM CAPACITORS
Solid electrolyte capacitors contain manganese dioxide,
which is formed on the tantalum pentoxide dielectric layer
by impregnating the pellet with a solution of manganous
nitrate. The pellet is then heated in an oven, and the
manganous nitrate is converted to manganese dioxide.
The pellet is next coated with graphite, followed by a layer
of metallic silver, which provides a conductive surface
between the pellet and the can in which it will be enclosed.
After assembly, the capacitors are tested and inspected to
assure long life and reliability. It offers excellent reliability
and high stability for consumer and commercial electronics
with the added feature of low cost.
Surface mount designs of “Solid Tantalum” capacitors use
lead frames or lead frameless designs as shown in the
accompanying drawings.
TANTALUM CAPACITORS FOR ALL DESIGN
CONSIDERATIONS
Solid electrolyte designs are the least expensive for a given
rating and are used in many applications where their very
small size for a given unit of capacitance is of importance.
They will typically withstand up to about 10 % of the rated
DC working voltage in a reverse direction. Also important
are their good low temperature performance characteristics
and freedom from corrosive electrolytes.
Vishay Sprague patented the original solid electrolyte
capacitors and was the first to market them in 1956. Vishay
Sprague has the broadest line of tantalum capacitors and
has continued its position of leadership in this field. Data
sheets covering the various types and styles of Vishay
Sprague capacitors for consumer and entertainment
electronics, industry, and military applications are available
where detailed performance characteristics must be
specified.
Vishay Sprague
TYPE 194D
SnPb or Gold Plated Ni Cathode
End Cap Termination
SnPb or Gold Plated Ni Anode
End Cap Termination
Cathode
Backfill
Conductive Silver
Epoxy Adhesive
Sintered Tantalum
Pellet
MnO2/Carbon/
Silver Coating
Sponge Teflon
Anode Backfill
TYPE T96
Intermediate
Cathode
Silver
Fuse
Cathode Termination
(Silver + Ni/Sn or
Ni/SnPb Plating)
Encapsulation
MnO2/Carbon/
Silver Coating
Epoxy Tower/
Sponge Teflon
Anode Termination
(Silver + Ni/Sn or
Sintered Tantalum
Ni/SnPb Plating)
Pellet
TYPE 195D, 572D, 591D, 592D/W, 594D,
595D, 695D, T95
Cathode Termination
(Silver + Ni/Sn/Plating)
Encapsulation
TYPE T98
Encapsulation
Anode Termination
(Silver + Ni/Sn/Plating)
Intermediate
Cathode
Silver
Fuse
MnO2 /Carbon/Silver
Coating
Sintered Tantalum
Pellet Sponge Teflon/Epoxy Tower
TYPE 597D/T97/13008
Cathode Termination
(Silver + Ni/Sn/Plating)
Encapsulation
Anode Termination
(Silver + Ni/Sn/Plating)
Cathode Termination
(Silver + Ni/Sn or
Ni/SnPb Plating)
Encapsulation
MnO2/Carbon/
Silver Coating
Epoxy Tower/
Sponge Teflon
Anode Termination
(Silver + Ni/Sn or Sintered Tantalum
Ni/SnPb Plating)
Pellet
MnO2/Carbon/Silver
Coating
Sintered Tantalum
Pellet
Revision: 23-Jul-13
Silver Epoxy
Sponge Teflon/Epoxy Tower
Document Number: 40150
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
COMMERCIAL PRODUCTS
SOLID TANTALUM CAPACITORS - CONFORMAL COATED
SERIES
592W
592D
591D
595D
594D
PRODUCT IMAGE
Surface mount TANTAMOUNT® chip, conformal coated
TYPE
FEATURES
Low profile, robust
design for use in
pulsed applications
Low profile,
maximum CV
Low profile, low ESR,
maximum CV
Maximum CV
Low ESR,
maximum CV
TEMPERATURE
RANGE
- 55 °C to + 125 °C
(above 40 °C, voltage
deratig is required)
CAPACITANCE
RANGE
330 μF to 2200 μF
1 μF to 2200 μF
1 μF to 1500 μF
0.1 μF to 1500 μF
1 μF to 1500 μF
6 V to 10 V
4 V to 50 V
4 V to 50 V
4 V to 50 V
4 V to 50 V
± 20 %
± 10 %, ± 20 %
± 10 %, ± 20 %
± 10 %, ± 20 %
± 10 %, ± 20 %
VOLTAGE RANGE
CAPACITANCE
TOLERANCE
- 55 °C to + 125 °C (above 85 °C, voltage derating is required)
LEAKAGE
CURRENT
0.01 CV or 0.5 μA, whichever is greater
DISSIPATION
FACTOR
14 % to 45 %
4 % to 50 %
4 % to 50 %
4 % to 20 %
4 % to 20 %
CASE CODES
C, M, X
S, A, B, C, D, R, M, X
A, B, C, D, R, M
T, S, A, B, C,
D, G, M, R
B, C, D, R
TERMINATION
100 % matte tin
100 % matte tin standard, tin/lead and gold plated available
SOLID TANTALUM CAPACITORS - CONFORMAL COATED
SERIES
597D
572D
695D
195D
194D
US and European
case sizes
Industrial version of
CWR06/CWR16
PRODUCT IMAGE
TANTAMOUNT® chip, conformal coated
TYPE
FEATURES
Ultra low ESR,
maximum CV,
multi-anode
TEMPERATURE
RANGE
CAPACITANCE
RANGE
VOLTAGE RANGE
Low profile,
maximum CV
Pad compatible with
194D and CWR06
- 55 °C to + 125 °C (above 85 °C, voltage derating is required)
10 μF to 1500 μF
2.2 μF to 220 μF
0.1 μF to 270 μF
0.1 μF to 330 μF
0.1 μF to 330 μF
4 V to 75 V
4 V to 35 V
4 V to 50 V
2 V to 50 V
4 V to 50 V
CAPACITANCE
TOLERANCE
± 10 %, ± 20 %
LEAKAGE
CURRENT
0.01 CV or 0.5 μA, whichever is greater
DISSIPATION
FACTOR
6 % to 20 %
6 % to 26 %
4 % to 8 %
4 % to 8 %
4 % to 10 %
CASE CODES
V, D, E, R, F, Z, M, H
P, Q, S, A, B, T
A, B, D, E, F, G, H
C, S, V, X, Y, Z, R,
A, B, D, E, F, G, H
A, B, C, D, E, F, G, H
TERMINATION
100 % matte tin
standard, tin/lead
solder plated
available
100 % matte tin
standard, gold plated
available
Revision: 23-Jul-13
100 % matte tin standard,
tin/lead and gold plated available
Gold plated standard;
tin/lead solder plated
and hot solder
dipped available
Document Number: 40150
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
HIGH RELIABILITY PRODUCTS
SOLID TANTALUM CAPACITORS - CONFORMAL COATED
SERIES
CWR06
CWR16
CWR26
13008
PRODUCT IMAGE
TANTAMOUNT® chip, conformal coated
TYPE
FEATURES
MIL-PRF-55365/4
qualified
TEMPERATURE RANGE
CAPACITANCE RANGE
VOLTAGE RANGE
CAPACITANCE TOLERANCE
CASE CODES
MIL-PRF-55365/13
qualified
DLA approved
- 55 °C to + 125 °C (above 85 °C, voltage derating is required)
0.10 μF to 100 μF
0.33 μF to 330 μF
10 μF to 100 μF
10 μF to 1500 μF
4 V to 50 V
4 V to 35 V
15 V to 35 V
4 V to 63 V
± 5 %, ± 10 %,
± 20 %
± 5 %, ± 10 %,
± 20 %
± 5 %, ± 10 %,
± 20 %
± 10 %, ± 20 %
LEAKAGE CURRENT
DISSIPATION FACTOR
MIL-PRF-55365/13
qualified
0.01 CV or 0.5 μA,
whichever is greater
0.01 CV or 1.0 μA, whichever is greater
6 % to 10 %
6 % to 10 %
6 % to 12 %
6 % to 20 %
A, B, C, D, E, F, G, H
A, B, C, D, E, F, G, H
F, G, H
V, E, F, R, Z, D, M, H, N
TERMINATION
Gold plated; tin/lead; tin/lead solder fused
Tin/lead
SOLID TANTALUM CAPACITORS - CONFORMAL COATED
SERIES
T95
T96
T97
T98
PRODUCT IMAGE
TANTAMOUNT® chip, Hi-Rel COTS, conformal coated
TYPE
FEATURES
TEMPERATURE RANGE
CAPACITANCE RANGE
VOLTAGE RANGE
CAPACITANCE TOLERANCE
High reliability,
built in fuse
High reliability
CASE CODES
TERMINATION
Revision: 23-Jul-13
High reliability,
ultra low ESR, built in
fuse, multi-anode
- 55 °C to + 125 °C (above 85 °C, voltage derating is required)
0.15 μF to 680 μF
10 μF to 680 μF
10 μF to 1500 μF
10 μF to 1500 μF
4 V to 50 V
4 V to 50 V
4 V to 75 V
4 V to 75 V
± 10 %, ± 20 %
± 10 %, ± 20 %
± 10 %, ± 20 %
± 10 %, ± 20 %
LEAKAGE CURRENT
DISSIPATION FACTOR
High reliability,
ultra low ESR,
multi-anode
0.01 CV or 0.5 μA, whichever is greater
4 % to 14 %
6 % to 14 %
6 % to 20 %
6 % to 10 %
A, B, C, D, R, S, V, X, Y, Z
R
V, E, F, R, Z, D, M, H, N
V, E, F, R, Z, M, H
100 % matte tin, tin/lead
Document Number: 40150
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
TAPE AND REEL PACKAGING in inches [millimeters]
0.157 ± 0.004
[4.0 ± 0.10]
T2
(max.)
Deformation
between
embossments
0.024
[0.600]
max.
0.059 + 0.004 - 0.0
[1.5 + 0.10 - 0.0]
Top
cover
tape
A0
K0
B1 (max.) (6)
Top
cover
tape
For tape feeder
reference only
including draft.
Concentric around B0
0.004 [0.10]
max.
10 pitches cumulative
tolerance on tape
± 0.008 [0.200]
Embossment
0.079 ± 0.002
0.069 ± 0.004
[2.0 ± 0.05]
[1.75 ± 0.10]
0.030 [0.75]
min. (3)
B0
F
20°
W
Maximum
component
rotation
0.030 [0.75]
min. (4)
(Side or front sectional view)
Center lines
of cavity
P1
D1 (min.) for components
(5)
.
0.079 x 0.047 [2.0 x 1.2] and larger
USER DIRECTION
OF FEED
Maximum
cavity size (1)
Cathode (-)
R
min.
Anode (+)
DIRECTION OF FEED
20° maximum
component rotation
Typical
component
cavity
center line
B0
A0
(Top view)
Typical
component
center line
Bending radius (2)
3.937 [100.0]
0.039 [1.0]
max.
Tape
0.039 [1.0]
max.
0.9843 [250.0]
Camber
(Top view)
Allowable camber to be 0.039/3.937 [1/100]
Non-cumulative over 9.843 [250.0]
R minimum:
8 mm = 0.984" (25 mm)
12 mm and 16 mm = 1.181" (30 mm)
Tape and reel specifications: All case sizes are
available on plastic embossed tape per EIA-481.
Standard reel diameter is 7" (178 mm).
Lengthwise orientation at capacitors in tape
Cathode (-)
DIRECTION OF FEED
Anode (+)
H-Case only
Notes
• Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
(1) A , B , K , are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body
0
0
0
dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the
cavity (A0, B0, K0) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm) maximum. The clearance allowed must also prevent
rotation of the component within the cavity of not more than 20°.
(2) Tape with components shall pass around radius “R” without damage. The minimum trailer length may require additional length to provide
“R” minimum for 12 mm embossed tape for reels with hub diameters approaching N minimum.
(3) This dimension is the flat area from the edge of the sprocket hole to either outward deformation of the carrier tape between the embossed
cavities or to the edge of the cavity whichever is less.
(4) This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier
tape between the embossed cavity or to the edge of the cavity whichever is less.
(5) The embossed hole location shall be measured from the sprocket hole controlling the location of the embossement. Dimensions of
embossement location shall be applied independent of each other.
(6) B dimension is a reference dimension tape feeder clearance only.
1
Revision: 23-Jul-13
Document Number: 40150
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
CARRIER TAPE DIMENSIONS in inches [millimeters]
TAPE WIDTH
W
D0
8 mm
0.315
+ 0.012/- 0.004
[8.0 + 0.3/- 0.1]
12 mm
0.479
+ 0.012/- 0.004
[12.0 + 0.3/- 0.1]
16 mm
24 mm
0.635
+ 0.012/- 0.004
[16.0 + 0.3/- 0.1]
P2
F
0.078 ± 0.0019
[2.0 ± 0.05]
0.059
+ 0.004/- 0
[1.5 + 0.1/- 0]
0.14 ± 0.0019
[3.5 ± 0.05]
0.216 ± 0.0019
[5.5 ± 0.05]
0.078 ± 0.004
[2.0 ± 0.1]
0.945 ± 0.012
[24.0 ± 0.3]
E1
E2 min.
0.246
[6.25]
0.324 ± 0.004
[1.75 ± 0.1]
0.403
[10.25]
0.295 ± 0.004
[7.5 ± 0.1]
0.570
[14.25]
0.453 ± 0.004
[11.5 ± 0.1]
0.876
[22.25]
CARRIER TAPE DIMENSIONS in inches [millimeters]
TYPE
592D
592W
591D
595D
594D
695D
Revision: 23-Jul-13
CASE CODE
TAPE WIDTH
W
IN mm
A
8
B
12
P1
K0 max.
B1 max.
0.157 ± 0.004
[4.0 ± 0.10]
0.058 [1.47]
0.149 [3.78]
0.088 [2.23]
0.166 [4.21]
C
12
0.088 [2.23]
0.290 [7.36]
D
12
0.088 [2.23]
0.300 [7.62]
M
16
0.091 [2.30]
0.311 [7.90]
R
12
0.088 [2.23]
0.296 [7.52]
S
8
0.058 [1.47]
0.139 [3.53]
T
12
0.088 [2.23]
0.166 [4.21]
0.011 [2.72]
0.594 [15.1]
0.063 [1.60]
0.152 [3.86]
X
24
A
8
B
12
C
12
0.315 ± 0.004
[8.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.472 ± 0.004
[12.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.088 [2.23]
0.166 [4.21]
0.118 [2.97]
0.290 [7.36]
0.119 [3.02]
0.296 [7.52]
0.111 [2.83]
0.234 [5.95]
0.098 [2.50]
0.232 [5.90]
D
12
G
12
H
12
M
12
0.157 ± 0.004
[4.0 ± 0.10]
0.085 [2.15]
0.152 [3.85]
R
12
0.315 ± 0.004
[8.0 ± 0.10]
0.148 [3.78]
0.296 [7.52]
S
8
0.058 [1.47]
0.149 [3.78]
T
8
A
8
0.315 ± 0.004
[8.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.054 [1.37]
0.093 [2.36]
0.058 [1.47]
0.139 [3.53]
0.059 [1.50]
0.189 [4.80]
0.063 [1.62]
0.191 [4.85]
0.074 [1.88]
0.239 [6.07]
B
12
D
12
E
12
F
12
0.315 ± 0.004
[8.0 ± 0.10]
0.075 [1.93]
0.259 [6.58]
G
12
0.157 ± 0.004
[4.0 ± 0.10]
0.109 [2.77]
0.301 [7.65]
H
16
0.315 ± 0.004
[8.0 ± 0.10]
0.124 [3.15]
0.31 [7.87]
0.157 ± 0.004
[4.0 ± 0.10]
Document Number: 40150
6
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
CARRIER TAPE DIMENSIONS in inches [millimeters]
TYPE
CASE CODE
TAPE WIDTH
W
IN mm
A
B
C
D
E
8
12
8
12
12
F
12
G
12
H (1)
12
R
12
S
V
X
Y
Z
A
B
P
P
Q
S
T
A
B
C
D
E
F
G
H
D
E
F
H
M
N
R
8
8
12
12
12
8
12
8
8
8
8
12
8
12
12
12
12
12
16
16
16
16
16
16
16
16
16
V
12
195D
572D
194D
CWR06
CWR16
CWR26
597D
T97
13008
Z
16
A
B
C
D
R
S
V
X
Y
Z
8
12
12
12
12
8
8
12
12
12
T96
R
16
T98
F
M
Z
16
16
16
T95
P1
K0 max.
B1 max.
0.157 ± 0.004
[4.0 ± 0.10]
0.058 [1.47]
0.059 [1.50]
0.054 [1.37]
0.067 [1.70]
0.074 [1.88]
0.139 [3.53]
0.189 [4.80]
0.093 [2.36]
0.179 [4.55]
0.239 [6.07]
0.076 [1.93]
0.259 [6.58]
0.109 [2.77]
0.301 [7.65]
0.122 [3.11]
0.163 [4.14]
0.315 ± 0.004
[8.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.472 ± 0.004
[12.0 ± 0.1]
0.315 ± 0.004
[8.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.315 ± 0.004
[8.0 ± 0.10]
0.317 ± 0.004
[8.0 ± 0.10]
0.476 ± 0.004
[12.0 ± 0.1]
0.317 ± 0.004
[8.0 ± 0.10]
0.476 ± 0.004
[12.0 ± 0.1]
0.157 ± 0.004
[4.0 ± 0.10]
0.317 ± 0.004
[8.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.149 [3.78]
0.296 [7.52]
0.058 [1.47]
0.060 [1.52]
0.069 [1.75]
0.089 [2.26]
0.114 [2.89]
0.058 [1.47]
0.087 [2.20]
0.043 [1.10]
0.052 [1.32]
0.054 [1.37]
0.058 [1.47]
0.061 [1.55]
0.069 [1.75]
0.073 [1.85]
0.069 [1.75]
0.068 [1.72]
0.074 [1.88]
0.091 [2.31]
0.134 [3.40]
0.129 [3.28]
0.150 [3.80]
0.173 [4.40]
0.205 [5.20]
0.224 [5.70]
0.193 [4.90]
0.283 [7.20]
0.159 [4.05]
0.149 [3.78]
0.150 [3.80]
0.296 [7.52]
0.296 [7.52]
0.288 [7.31]
0.149 [3.78]
0.166 [4.21]
0.102 [2.60]
0.106 [2.70]
0.140 [3.55]
0.149 [3.78]
0.164 [4.16]
0.139 [3.53]
0.189 [4.80]
0.244 [6.20]
0.191 [4.85]
0.239 [6.07]
0.262 [6.65]
0.289 [7.34]
0.319 [8.10]
0.313 [7.95]
0.343 [8.70]
0.309 [7.85]
0.313 [7.95]
0.339 [8.60]
0.323 [8.20]
0.313 [7.95]
0.088 [2.23]
0.300 [7.62]
0.239 [6.06]
0.311 [7.90]
0.063 [1.60]
0.088 [2.23]
0.117 [2.97]
0.119 [3.02]
0.149 [3.78]
0.058 [1.47]
0.060 [1.52]
0.069 [1.75]
0.089 [2.26]
0.114 [2.89]
0.152 [3.86]
0.166 [4.21]
0.290 [7.36]
0.296 [7.52]
0.296 [7.52]
0.149 [3.78]
0.150 [3.80]
0.296 [7.52]
0.296 [7.52]
0.288 [7.31]
0.476 ± 0.004
[12.0 ± 0.1]
0.159 [4.05]
0.313 [7.95]
0.476 ± 0.004
[12.0 ± 0.1]
0.239 [6.06]
0.193 [4.90]
0.272 [6.90]
0.311 [7.90]
0.339 [8.60]
0.307 [7.80]
Note
(1) H case only, packaging code T: Lengthwise orientation at capacitors in tape.
Revision: 23-Jul-13
Document Number: 40150
7
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
PAD DIMENSIONS in inches [millimeters]
B
C
B
A
CASE CODE
WIDTH (A)
PAD METALLIZATION (B)
SEPARATION (C)
592D/W - 591D
A
0.075 [1.9]
0.050 [1.3]
0.050 [1.3]
B
0.118 [3.0]
0.059 [1.5]
0.059 [1.5]
C
0.136 [3.5]
0.090 [2.3]
0.122 [3.1]
D
0.180 [4.6]
0.090 [2.3]
0.134 [3.4]
M
0.256 [6.5]
R
0.240 [6.1]
Anode pad: 0.095 [2.4]
Cathode pad: 0.067 [1.7]
Anode pad: 0.095 [2.4]
Cathode pad: 0.067 [1.7]
0.138 [3.5]
0.118 [3.0]
S
0.067 [1.7]
0.032 [0.8]
0.043 [1.1]
X
0.310 [7.9]
0.120 [3.0]
0.360 [9.2]
T
0.059 [1.5]
0.028 [0.7]
0.024 [0.6]
S
0.067 [1.7]
0.032 [0.8]
0.043 [1.1]
A
0.820 [2.1]
0.050 [1.3]
0.050 [1.3]
595D - 594D
B
0.118 [3.0]
0.059 [1.5]
0.059 [1.5]
C
0.136 [3.5]
0.090 [2.3]
0.122 [3.1]
D
0.180 [4.6]
0.090 [2.3]
0.134 [3.4]
G
0.156 [4.05]
0.090 [2.3]
0.082 [2.1]
M
0.110 [2.8]
0.087 [2.2]
0.134 [3.4]
R
0.248 [6.3]
0.090 [2.3]
0.140 [3.6]
A
0.067 [1.7]
0.043 [1.1]
0.028 [0.7]
195D
B
0.063 [1.6]
0.047 [1.2]
0.047 [1.2]
C
0.059 [1.5]
0.031 [0.8]
0.024 [0.6]
D
0.090 [2.3]
0.055 [1.4]
0.047 [1.2]
E
0.090 [2.3]
0.055 [1.4]
0.079 [2.0]
F
0.140 [3.6]
0.063 [1.6]
0.087 [2.2]
G
0.110 [2.8]
0.059 [1.5]
0.126 [3.2]
H
0.154 [3.9]
0.063 [1.6]
0.140 [3.6]
N
0.244 [6.2]
0.079 [2.0]
0.118 [3.0]
R
0.248 [6.3]
0.090 [2.3]
0.140 [3.6]
S
0.079 [2.0]
0.039 [1.0]
0.039 [1.0]
V
0.114 [2.9]
0.039 [1.0]
0.039 [1.0]
X
0.118 [3.0]
0.067 [1.7]
0.122 [3.1]
Y
0.118 [3.0]
0.067 [1.7]
0.122 [3.1]
Z
0.118 [3.0]
0.067 [1.7]
0.122 [3.1]
Revision: 23-Jul-13
Document Number: 40150
8
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
PAD DIMENSIONS in inches [millimeters]
B
C
B
A
CASE CODE
WIDTH (A)
PAD METALLIZATION (B)
SEPARATION (C)
0.040 [1.0]
CWR06/CWR16/CWR26 - 194D - 695D
A
0.065 [1.6]
0.50 [1.3]
B
0.065 [1.6]
0.70 [1.8]
0.055 [1.4]
C
0.065 [1.6]
0.70 [1.8]
0.120 [3.0]
D
0.115 [2.9]
0.70 [1.8]
0.070 [1.8]
E
0.115 [2.9]
0.70 [1.8]
0.120 [3.0]
F
0.150 [3.8]
0.70 [1.8]
0.140 [3.6]
G
0.125 [3.2]
0.70 [1.8]
0.170 [4.3]
H
0.165 [4.2]
0.90 [2.3]
0.170 [4.3]
T95
B
0.120 [3.0]
0.059 [1.5]
0.059 [1.5]
C
0.136 [3.5]
0.090 [2.3]
0.120 [3.1]
D
0.180 [4.6]
0.090 [2.3]
0.136 [3.47]
R
0.248 [6.3]
0.090 [2.3]
0.140 [3.6]
S
0.080 [2.03]
0.040 [1.02]
0.040 [1.02]
V
0.114 [2.9]
0.040 [1.02]
0.040 [1.02]
X, Y, Z
0.114 [2.9]
0.065 [1.65]
0.122 [3.1]
R
0.248 [6.3]
0.090 [2.3]
0.140 [3.6]
D, E, V
0.196 [4.9]
0.090 [2.3]
0.140 [3.6]
F, R, Z
0.260 [6.6]
0.090 [2.3]
0.140 [3.6]
M, H, N
0.284 [7.2]
0.090 [2.3]
0.140 [3.6]
T96
597D - T97 - T98 - 13008
PAD DIMENSIONS in inches [millimeters]
B
C
B1
A
CASE CODE
572D
A
Q
S
B
P
T
Revision: 23-Jul-13
WIDTH (A)
PAD METALLIZATION (B)
PAD METALLIZATION (B1)
SEPARATION (C)
0.079 [2.0]
0.079 [2.0]
0.079 [2.0]
0.110 [2.8]
0.055 [1.4]
0.110 [2.8]
0.039 [1.0]
0.039 [1.0]
0.039 [1.0]
0.039 [1.0]
0.024 [0.6]
0.035 [0.9]
0.035 [0.9]
0.035 [0.9]
0.035 [0.9]
0.035 [0.9]
0.024 [0.6]
0.031 [0.8]
0.047 [1.2]
0.047 [1.2]
0.047 [1.2]
0.055 [1.4]
0.035 [0.9]
0.055 [1.4]
Document Number: 40150
9
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
RECOMMENDED REFLOW PROFILES
Capacitors should withstand Reflow profile as per J-STD-020 standard
TEMPERATURE (°C)
Tp
tp
Max. ramp-up rate = 3 °C/s
Max. ramp-down rate = 6 °C/s
TL
Ts max.
Tc = 5 °C
tL
Preheat area
Ts min.
ts
25
Time 25 °C to peak
TIME (s)
PROFILE FEATURE
Preheat/soak
Temperature min. (Ts min.)
Temperature max. (Ts max.)
Time (ts) from (Ts min. to Ts max.)
Ramp-up
Ramp-up rate (TL to Tp)
Liquidous temperature (TL)
Time (tL) maintained above TL
Peak package body temperature (Tp)
Time (tp)* within 5 °C of the specified
classification temperature (Tc)
Ramp-down
Ramp-down rate (Tp to TL)
Time 25 °C to peak temperature
SnPb EUTECTIC ASSEMBLY
LEAD (Pb)-FREE ASSEMBLY
100 °C
150 °C
60 s to 120 s
150 °C
200 °C
60 s to 120 s
3 °C/s max.
3 °C/s max.
183 °C
217 °C
60 s to 150 s
60 s to 150 s
Depends on type and case – see table below
20 s
30 s
6 °C/s max.
6 min max.
6 °C/s max.
8 min max.
PEAK PACKAGE BODY TEMPERATURE (Tp)
TYPE/CASE CODE
PEAK PACKAGE BODY TEMPERATURE (Tp)
SnPb EUTECTIC PROCESS
LEAD (Pb)-FREE PROCESS
591D/592D - all cases, except X25H, M and R cases
235 °C
591D/592D - X25H, M and R cases
220 °C
250 °C
594D/595D - all cases except C, D and R
235 °C
260 °C
594D/595D - C, D and R case
220 °C
250 °C
n/a
260 °C
572D all cases
260 °C
T95 B, S, V, X, Y cases
235 °C
260 °C
T95 C, D, R and Z cases
220 °C
250 °C
T96 R case
220 °C
250 °C
195D all cases, except G, H, R and Z
235 °C
260 °C
195D G, H, R and Z cases
220 °C
250 °C
695D all cases, except G and H cases
235 °C
260 °C
695D G, H cases
220 °C
250 °C
597D, T97, T98 all cases, except V case
220 °C
250 °C
597D, T97, T98 V case
230 °C
260 °C
194D all cases, except H and G cases
235 °C
260 °C
194D H and G cases
220 °C
250 °C
Revision: 23-Jul-13
Document Number: 40150
10
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
GUIDE TO APPLICATION
1.
AC Ripple Current: The maximum allowable ripple
current shall be determined from the formula:
I R MS =
5.
Power Dissipation: Power dissipation will be
affected by the heat sinking capability of the
mounting surface. Non-sinusoidal ripple current may
produce heating effects which differ from those
shown. It is important that the equivalent IRMS value
be established when calculating permissible
operating levels. (Power dissipation calculated using
derating factor (see paragraph 4)).
6.
Attachment:
6.1
Soldering: Capacitors can be attached by
conventional soldering techniques, convection,
infrared reflow, wave soldering and hot plate
methods. The soldering profile chart shows typical
recommended time/temperature conditions for
soldering. Preheating is recommended to reduce
thermal stress. The recommended maximum preheat
rate is 2 °C/s. Attachment with a soldering iron is not
recommended due to the difficulty of controlling
temperature and time at temperature. The soldering
iron must never come in contact with the capacitor.
7.
Recommended Mounting Pad Geometries: The
nib must have sufficient clearance to avoid electrical
contact with other components. The width
dimension indicated is the same as the maximum
width of the capacitor. This is to minimize lateral
movement.
8.
Cleaning (Flux Removal) After Soldering:
TANTAMOUNT® capacitors are compatible with all
commonly used solvents such as TES, TMS, Prelete,
Chlorethane, Terpene and aqueous cleaning media.
However, CFC/ODS products are not used in the
production of these devices and are not
recommended. Solvents containing methylene
chloride or other epoxy solvents should be avoided
since these will attack the epoxy encapsulation
material.
P
-----------R ESR
where,
P=
Power dissipation in W at + 25 °C as given in
the tables in the product datasheets (Power
Dissipation).
RESR = The capacitor equivalent series resistance at
the specified frequency
2.
AC Ripple Voltage: The maximum allowable ripple
voltage shall be determined from the formula:
V RMS = I R MS x Z
or, from the formula:
P
V R MS = Z -----------R ESR
where,
P=
Power dissipation in W at + 25 °C as given in
the tables in the product datasheets (Power
Dissipation).
RESR = The capacitor equivalent series resistance at
the specified frequency
Z=
The capacitor impedance at the specified
frequency
2.1
The sum of the peak AC voltage plus the applied DC
voltage shall not exceed the DC voltage rating of the
capacitor.
2.2
The sum of the negative peak AC voltage plus the
applied DC voltage shall not allow a voltage reversal
exceeding 10 % of the DC working voltage at
+ 25 °C.
3.
Reverse Voltage: Solid tantalum capacitors are not
intended for use with reverse voltage applied.
However, they have been shown to be capable of
withstanding momentary reverse voltage peaks of up
to 10 % of the DC rating at 25 °C and 5 % of the DC
rating at + 85 °C.
4.
Temperature Derating: If these capacitors are to be
operated at temperatures above + 25 °C, the
permissible RMS ripple current or voltage shall be
calculated using the derating factors as shown:
TEMPERATURE
+ 25 °C
+ 85 °C
+ 125 °C
Revision: 23-Jul-13
DERATING FACTOR
1.0
0.9
0.4
Document Number: 40150
11
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000