VISHAY TL8A0227M004C

TL8
www.vishay.com
Vishay Sprague
Solid Tantalum Chip Capacitors, MICROTAN®,
High CV Leadframeless Molded Low Profile
FEATURES
• Ultra-low profile: 0.8 mm to 1.0 mm in a variety
of case sizes
• Highest capacitance-voltage product in industry
• Lead (Pb)-free L-shaped terminations for
superior board mounting
• Material categorization:
For definitions of compliance please see
www.vishay.com/doc?99912
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55 °C to + 125 °C
(above 85 °C, voltage derating is required)
Capacitance Tolerance: ± 10 % ± 20 %
Voltage Range: 4 VDC to 35 VDC
Capacitance Range: 3.3 μF to 220 μF
ORDERING INFORMATION
TL8
A0
227
M
004
C
TYPE
CASE CODE
CAPACITANCE
CAPACITANCE
TOLERANCE
DC VOLTAGE RATING
AT + 85 °C
TERMINATION/
PACKAGING
See Ratings
and Case
Codes table.
This is expressed
in pF. The first two
digits are the
significant figures.
The third is the
number of zeros
to follow.
M = ± 20 %
K = ± 10 %
This is expressed in V.
To complete the three-digit
block, zeros precede the
voltage rating. A decimal
point is indicated by an “R”
(6R3 = 6.3 V).
C = 100 % tin
7" (178 mm) reel
Note
• Preferred tolerance and reel sizes are in bold.
We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size.
Voltage substitutions will be marked with the higher voltage rating.
DIMENSIONS in inches [millimeters]
Anode Polarity Bar
Anode Termination
W
C
P1
H
L
P1
P2
CASE CODE
H (MAX.)
W0
0.039
[1.0]
W9
0.035
[0.9]
A0
B0
Revision: 15-Jan-13
Cathode Termination
L
W
P1
P2 (REF.)
C
0.079 ± 0.008
[2.00 ± 0.20]
0.050 ± 0.008
[1.25 ± 0.20]
0.020 ± 0.004
[0.50 ± 0.10]
0.040
[1.00]
0.035 ± 0.004
[0.90 ± 0.10]
0.039
[1.0]
0.126 ± 0.008
[3.20 ± 0.20]
0.063 ± 0.008
[1.60 ± 0.20]
0.031 ± 0.004
[0.80 ± 0.10]
0.063
[1.60]
0.047 ± 0.004
[1.20 ± 0.10]
0.039
[1.0]
0.138 ± 0.008
[3.50 ± 0.20]
0.110 ± 0.008
[2.80 ± 0.20]
0.031 ± 0.004
[0.80 ± 0.20]
0.078
[1.95]
0.095 ± 0.004
[2.40 ± 0.10]
Document Number: 40156
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TL8
www.vishay.com
Vishay Sprague
RATINGS AND CASE CODES
μF
4V
6.3 V
10 V
16 V
20 V
25 V
35 V
1.5
2.2
A0 (1)
3.3
4.7
W0
(1)
6.8
W0 (1)
10
A0 (1)
15
22
W9
W0 (1)
33
47
W0
(1)
B0
W9 (1)/A0 (1)
68
100
A0/B0 (1)
A0
150
220
A0
330
470
Note
(1) In development.
MARKING
VOLTAGE CODE
V
Wx-cases
Voltage Capacitance
Polarity Bar Code Code
GJ
Ax-cases
Voltage EIA Capacitance
Polarity Bar Code
Code (pF)
J 107
Revision: 15-Jan-13
CAPACITANCE CODE
CODE
CAP, μF
CODE
2.5
e
0.68
w
4.0
G
1.0
A
6.3
J
2.2
J
10
A
3.3
N
16
C
4.7
S
20
D
6.8
W
25
E
10

35
V
15
e
50
T
22
j
33
n
47
s
68
w
100
A
150
E
220
J
Bx-cases
Polarity Bar
Capacitance
Voltage
330 4
2
Vishay
Logo
Document Number: 40156
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TL8
www.vishay.com
Vishay Sprague
STANDARD RATINGS
CAPACITANCE
(μF)
CASE CODE
PART NUMBER
220
A0
TL8A0227M004C
MAX. DCL
AT + 25 °C (μA)
MAX. DF
AT + 25 °C
120 Hz
(%)
MAX. ESR
AT + 25 °C
100 kHz
()
MAX. RIPPLE
100 kHz
IRMS
(A)
7.0
0.089
4 VDC AT + 40 °C; 2.5 VDC + 85 °C; 1.6 VDC AT + 125 °C
88
80
6.3 VDC AT + 40 °C; 4.0 VDC + 85 °C; 2.5 VDC AT + 125 °C
47
W0 (1)
TL8W0476M6R3C
3.0
25
3.0
0.108
100
A0
TL8A0107M6R3C
6.3
30
1.1
0.220
10 VDC AT + 40 °C; 6.3 VDC + 85 °C; 4.0 VDC AT + 125 °C
22
TL8W9226M010C
22
40
10.0
0.084
W0
(1)
TL8W0336M010C
3.3
30
6.0
0.076
47
W9
(1)
TL8W9476M010C
9.4
35
5.0
0.084
47
A0 (1)
TL8A0476M010C
15
30
5.0
0.105
100
A0
TL8A0107M010C
100
50
7.0
0.089
100
B0 (1)
TL8B0107M010C
10
18
TBD
TBD
4.0
TBD
33
W9
16 VDC AT + 40 °C; 10 VDC + 85 °C; 6.3 VDC AT + 125 °C
10
W0
(1)
A0
(1)
TL8W0106M016C
1.6
18
20 VDC AT + 40 °C; 13 VDC + 85 °C; 8 VDC AT + 125 °C
10
33
B0
TL8A0106M020C
4.0
15
5.0
0.105
TL8B0336M020C
33
15
5.0
0.118
TBD
TBD
10.0
0.074
25 VDC AT + 40 °C; 17 VDC + 85 °C; 10 VDC AT + 125 °C
4.7
W0 (1)
TL8W0475M025C
TBD
TBD
35 VDC AT + 40 °C; 23 VDC + 85 °C; 14 VDC AT + 125 °C
3.3
A0 (1)
TL8A0335(1)035C
1.2
10
Notes
• Part number definition:
(1) Capacitance tolerance: K = 10 %, M = 20 %
(1) In development.
Revision: 15-Jan-13
Document Number: 40156
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TL8
www.vishay.com
Vishay Sprague
CAPACITORS PERFORMANCE CHARACTERISTICS
ELECTRICAL PERFORMANCE CHARACTERISTICS
ITEM
PERFORMANCE CHARACTERISTICS
Category temperature range
- 55 °C to + 125 °C (with voltage derating)
Capacitance tolerance
± 20 %, ± 10 % (at 120 Hz) 2 VRMS at + 25 °C using a capacitance bridge
Dissipation factor (at 120 Hz)
Limits per Standard Ratings table. Tested via bridge method, at 25 °C, 120 Hz
ESR (100 kHz)
Limits per Standard Ratings table. Tested via bridge method, at 25 °C, 100 kHz
Leakage current
After application of RV applied to capacitors for 5 min using a steady source of power with 1 k resistor in
series with the capacitor under test, leakage current at 25 °C is not more than described in.
Operation temperatures
Rated voltage
- 55 °C/+ 40 °C
4V
6.3 V
10 V
16 V
20 V
25 V
35 V
Category voltage
+ 40 °C/+ 85 °C
2.5 V
4.0 V
6.3 V
10 V
13 V
17 V
23 V
Category voltage
+ 85 °C/+ 125 °C
1.6 V
2.5 V
4V
6.3 V
8.0 V
10 V
14 V
TYPICAL LEAKAGE CURRENT FACTOR RANGE
LEAKAGE CURRENT FACTOR
100
+ 125 °C
+ 85 °C
10
+ 55 °C
+ 25 °C
1.0
0 °C
0.1
- 55 °C
0.01
0.001
0
10
20
30
40
50
60
70
80
90
100
PERCENT OF RATED VOLTAGE
Notes
• At + 25 °C, the leakage current shall not exceed the value listed in the Standard Ratings table
• At + 85 °C, the leakage current shall not exceed 10 times the value listed in the Standard Ratings table
• At + 125 °C, the leakage current shall not exceed 12 times the value listed in the Standard Ratings table
Revision: 15-Jan-13
Document Number: 40156
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TL8
www.vishay.com
Vishay Sprague
PLASTIC TAPE AND REEL PACKAGING in inches [millimeters]
0.157 ± 0.004
[4.0 ± 0.10]
Tape thickness
Deformation
between
embossments
0.014
[0.35]
max.
0.059 + 0.004 - 0.0
[1.5 + 0.10 - 0.0]
Top
cover
tape
A0
K0
B1 (max.) (6)
10 pitches cumulative
tolerance on tape
± 0.008 [0.200]
Embossment
0.079 ± 0.002
0.069 ± 0.004
[2.0 ± 0.05]
[1.75 ± 0.10]
0.030 [0.75]
min. (3)
B0
For tape feeder
reference only
including draft.
Concentric around B0 (5)
W
20°
Maximum
component
rotation
0.030 [0.75]
min. (4)
Top cover
tape
0.004 [0.10]
max.
F
(Side or front sectional view)
Center lines
of cavity
P1
D1 (min.) for components
(5)
.
0.079 x 0.047 [2.0 x 1.2] and larger
USER DIRECTION
OF FEED
Maximum
cavity size (1)
Cathode (-)
Anode (+)
DIRECTION OF FEED
20° maximum
component rotation
Typical
component
cavity
center line
B0
A0
(Top view)
Typical
component
center line
3.937 [100.0]
0.039 [1.0]
max.
Tape
0.039 [1.0]
max.
0.9843 [250.0]
Camber
(Top view)
Allowable camber to be 0.039/3.937 [1/100]
Non-cumulative over 9.843 [250.0]
Tape and Reel Specifications: All case sizes are
available on plastic embossed tape per EIA-481.
Standard reel diameter is 7" [178 mm].
Notes
• Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
(1) A , B , K , are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body
0
0
0
dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the
cavity (A0, B0, K0) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm) maximum. The clearance allowed must also prevent
rotation of the component within the cavity of not more than 20°.
(2) Tape with components shall pass around radius “R” without damage. The minimum trailer length may require additional length to provide
“R” minimum for 12 mm embossed tape for reels with hub diameters approaching N minimum.
(3) This dimension is the flat area from the edge of the sprocket hole to either outward deformation of the carrier tape between the embossed
cavities or to the edge of the cavity whichever is less.
(4) This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier
tape between the embossed cavity or to the edge of the cavity whichever is less.
(5) The embossed hole location shall be measured from the sprocket hole controlling the location of the embossement. Dimensions of
embossement location shall be applied independent of each other.
(6) B dimension is a reference dimension tape feeder clearance only.
1
CARRIER TAPE DIMENSIONS in inches [millimeters]
CASE CODE
TAPE SIZE
A0
8 mm
W0
8 mm
W9
8 mm
B0
12 mm
Revision: 15-Jan-13
B1
(MAX.)
0.165
[4.2]
0.094
[2.4]
0.126
[3.2]
0.181
[4.61]
D1
(MIN.)
0.039
[1.0]
0.029
[0.75]
0.029
[0.75]
0.059
[1.5]
F
0.138 ± 0.002
[3.5 ± 0.05]
0.138 ± 0.002
[3.5 ± 0.05]
0.138 ± 0.002
[3.5 ± 0.05]
0.217 ± 0.002
[5.5 ± 0.05]
K0
(MAX.)
0.094
[2.4]
0.045
[1.15]
0.045
[1.15]
0.049
[1.25]
P1
W
0.157 ± 0.004
[4.0 ± 0.1]
0.157 ± 0.004
[4.0 ± 0.1]
0.157 ± 0.004
[4.0 ± 0.1]
0.157 ± 0.004
[4.0 ± 0.1]
0.315 ± 0.012
[8.0 ± 0.3]
0.315 ± 0.012
[8.0 ± 0.3]
0.315 ± 0.012
[8.0 ± 0.3]
0.472 ± 0.012
[12 ± 0.3]
Document Number: 40156
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TL8
www.vishay.com
Vishay Sprague
STANDARD PACKAGING QUANTITY
QUANTITY (pcs/reel)
CASE CODE
7" REEL
A0
2500
W0, W9
3000
B0
3000
VOLTAGE VS. TEMPERATURE RATING
120
RATED VOLTAGE (%)
100
80
100 %
100 %
80 %
80 %
100 %
Rated range
Recommended
derating
80 %
63 %
60
40 %
50 %
40
TL8 recommended derating
33 %
20
0
- 55
0
+ 40
TEMPERATURE (°C)
+ 85
+ 125
POWER DISSIPATION
CASE CODE
MAXIMUM PERMISSIBLE POWER DISSIPATION AT + 25 °C (W) IN FREE AIR
A0
0.055
W0, W9
0.035
B0
0.070
Revision: 15-Jan-13
Document Number: 40156
6
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TL8
www.vishay.com
Vishay Sprague
RECOMMENDED REFLOW PROFILES
Capacitors should withstand Reflow profile as per J-STD-020 standard
Tp
TEMPERATURE (°C)
TL
Ts max.
Tc = 5 °C
tp
Max. ramp-up rate = 3 °C/s
Max. ramp-down rate = 6 °C/s
tL
Preheat area
Ts min.
ts
25
Time 25 °C to peak
TIME (s)
PROFILE FEATURE
LEAD (Pb)-FREE ASSEMBLY
Preheat/soak
Temperature min. (Ts min.)
150 °C
Temperature max. (Ts max.)
200 °C
Time (ts) from (Ts min. to Ts max.)
60 s to 120 s
Ramp-up
Ramp-up rate (TL to Tp)
3 °C/s max.
Liquidous temperature (TL)
217 °C
Time (tL) maintained above TL
60 s to 150 s
Peak package body temperature (Tp) max.
260 °C
Time (tp) within 5 °C of the peak max. temperature
30 s
Ramp-down
Ramp-down rate (Tp to TL)
6 °C/s max.
Time from 25 °C to peak temperature
8 min max.
PAD DIMENSIONS in inches [millimeters]
B
D
C
A
CASE CODE
A (MIN.)
B (NOM.)
C (NOM.)
D(NOM.)
Wx-cases
0.059 [1.50]
0.031 [0.80]
0.039 [1.00]
0.102 [2.60]
Ax-cases
0.071 [1.80]
0.067 [1.70]
0.053 [1.35]
0.187 [4.75]
Bx-cases
0.118 [3.00]
0.071 [1.80]
0.065 [1.65]
0.207 [5.25]
Revision: 15-Jan-13
Document Number: 40156
7
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TL8
www.vishay.com
Vishay Sprague
GUIDE TO APPLICATION
1.
AC Ripple Current: The maximum allowable ripple
current shall be determined from the formula:
I R MS =
2.
P
-----------R ESR
where,
P=
Power dissipation in W at + 25 °C as given in
the tables in the product datasheets (Power
Dissipation).
RESR = The capacitor equivalent series resistance at
the specified frequency
AC Ripple Voltage: The maximum allowable ripple
voltage shall be determined from the formula:
V RMS = I R MS x Z
or, from the formula:
P
V R MS = Z -----------R ESR
where,
P=
Power dissipation in W at + 25 °C as given in
the tables in the product datasheets (Power
Dissipation).
RESR = The capacitor equivalent series resistance at
the specified frequency.
Z=
The capacitor impedance at the specified
frequency.
2.1
The sum of the peak AC voltage plus the applied DC
voltage shall not exceed the DC voltage rating of the
capacitor.
2.2
The sum of the negative peak AC voltage plus the
applied DC voltage shall not allow a voltage reversal
exceeding 10 % of the DC working voltage at
+ 25 °C.
Reverse Voltage: These capacitors are capable of
withstanding peak voltages in the reverse direction
equal to 10 % of the DC rating at + 25 °C, 5 % of the
DC rating at + 85 °C and 1 % of the DC rating at
+ 125 °C.
Temperature Derating: If these capacitors are to be
operated at temperatures above + 25 °C, the
permissible RMS ripple current or voltage shall be
calculated using the derating factors as shown:
3.
4.
TEMPERATURE
+ 25 °C
+ 85 °C
+ 125 °C
5.
DERATING FACTOR
1.0
0.9
0.4
Power Dissipation: Power dissipation will be
affected by the heat sinking capability of the
mounting surface. Non-sinusoidal ripple current may
produce heating effects which differ from those
shown. It is important that the equivalent IRMS value
be established when calculating permissible
operating levels. (Power dissipation calculated using
+ 25 °C temperature rise).
PRODUCT INFORMATION
Micro Guide
Moisture Sensitivity
SELECTOR GUIDES
Solid Tantalum Selector Guide
Solid Tantalum Chip Capacitors
FAQ
Frequently Asked Questions
Revision: 15-Jan-13
6.
Printed Circuit Board Materials: Molded capacitors
are compatible with commonly used printed circuit
board materials (alumina substrates, FR4, FR5, G10,
PTFE-fluorocarbon and porcelanized steel).
7.
7.1
Attachment:
Solder Paste: The recommended thickness of the
solder paste after application is 0.007" ± 0.001"
[0.178 mm ± 0.025 mm]. Care should be exercised in
selecting the solder paste. The metal purity should be
as high as practical. The flux (in the paste) must be
active enough to remove the oxides formed on the
metallization prior to the exposure to soldering heat. In
practice this can be aided by extending the solder
preheat time at temperatures below the liquidous
state of the solder.
7.2
Soldering: Capacitors can be attached by
conventional soldering techniques; vapor phase,
convection reflow, infrared reflow, wave soldering,
and hot plate methods. The soldering profile charts
show recommended time/temperature conditions for
soldering. Preheating is recommended. The
recommended maximum ramp rate is 2 °C per s.
Attachment with a soldering iron is not
recommended due to the difficulty of controlling
temperature and time at temperature. The soldering
iron must never come in contact with the capacitor.
7.2.1 Backward and Forward Compatibility: Capacitors
with SnPb or 100 % tin termination finishes can be
soldered using SnPb or lead (Pb)-free soldering
processes.
8.
Cleaning (Flux Removal) After Soldering: Molded
capacitors are compatible with all commonly used
solvents such as TES, TMS, Prelete, Chlorethane,
Terpene and aqueous cleaning media. However,
CFC/ODS products are not used in the production of
these devices and are not recommended. Solvents
containing methylene chloride or other epoxy
solvents should be avoided since these will attack
the epoxy encapsulation material.
8.1
9.
When using ultrasonic cleaning, the board may
resonate if the output power is too high. This
vibration can cause cracking or a decrease in the
adherence of the termination. DO NOT EXCEED 9W/l
at 40 kHz for 2 min.
Recommended Mounting Pad Geometries: Proper
mounting pad geometries are essential for
successful solder connections. These dimensions
are highly process sensitive and should be designed
to minimize component rework due to unacceptable
solder joints. The dimensional configurations shown
are the recommended pad geometries for both wave
and reflow soldering techniques. These dimensions
are intended to be a starting point for circuit board
designers and may be fine tuned if necessary based
upon the peculiarities of the soldering process
and/or circuit board design.
www.vishay.com/doc?40115
www.vishay.com/doc?40135
www.vishay.com/doc?49053
www.vishay.com/doc?40091
www.vishay.com/doc?40110
Document Number: 40156
8
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Vishay:
TL8A0227M004C TL8W9226M010C TL8A0107M010C TL8A0107M6R3C TL8B0336M020C