ALTERA 5M80ZM64C5N

MAX V Device Handbook
MAX V Device Handbook
101 Innovation Drive
San Jose, CA 95134
www.altera.com
Subscribe
© 2011 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat.
& Tm. Off. and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective
holders as described at www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance
with Altera’s standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or
liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera. Altera
customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or
services.
MAX V Device Handbook
May 2011
Altera Corporation
Contents
Section I. MAX V Device Core
Chapter 1. MAX V Device Family Overview
Feature Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
Integrated Software Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3
Device Pin-Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–3
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4
Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4
Chapter 2. MAX V Architecture
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
Logic Array Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4
LAB Interconnects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6
LAB Control Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6
Logic Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
LUT Chain and Register Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9
addnsub Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9
LE Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9
Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10
Dynamic Arithmetic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10
Carry-Select Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–11
Clear and Preset Logic Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–13
LE RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–13
MultiTrack Interconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–14
Global Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–19
User Flash Memory Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–21
UFM Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–22
Internal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–22
Program, Erase, and Busy Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–23
Auto-Increment Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–23
Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–23
UFM Block to Logic Array Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–24
Core Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–25
I/O Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–26
Fast I/O Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–27
I/O Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–28
I/O Standards and Banks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–29
PCI Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–32
LVDS and RSDS Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–32
Schmitt Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–32
Output Enable Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–33
Programmable Drive Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–33
Slew-Rate Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–34
Open-Drain Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–34
Programmable Ground Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–34
Bus-Hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–34
Programmable Pull-Up Resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–35
Programmable Input Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–35
May 2011
Altera Corporation
MAX V Device Handbook
iv
Contents
MultiVolt I/O Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–35
Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–36
Chapter 3. DC and Switching Characteristics for MAX V Devices
Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
Programming/Erasure Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–3
DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–3
Output Drive Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–5
I/O Standard Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–5
Bus Hold Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8
Power-Up Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–9
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10
Timing Model and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10
Preliminary and Final Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–11
Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–11
Internal Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–12
External Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–19
External Timing I/O Delay Adders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–23
Maximum Input and Output Clock Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–26
LVDS and RSDS Output Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–27
JTAG Timing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–29
Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–30
Section II. System Integration in MAX V Devices
Chapter 4. Hot Socketing and Power-On Reset in MAX V Devices
MAX V Hot-Socketing Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Devices Can Be Driven Before Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
I/O Pins Remain Tri-Stated During Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
Signal Pins Do Not Drive the VCCIO or VCCINT Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
AC and DC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
Hot-Socketing Feature Implementation in MAX V Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–3
Power-On Reset Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Power-Up Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–6
Chapter 5. Using MAX V Devices in Multi-Voltage Systems
I/O Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1
MultiVolt I/O Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
5.0-V Device Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3
Recommended Operating Conditions for 5.0-V Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–7
Power-Up Sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–8
Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–8
Chapter 6. JTAG and In-System Programmability in MAX V Devices
IEEE Std. 1149.1 Boundary-Scan Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–1
JTAG Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–4
Parallel Flash Loader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–4
In-System Programmability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–5
IEEE 1532 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–6
Jam Standard Test and Programming Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–6
MAX V Device Handbook
May 2011
Altera Corporation
Contents
v
Programming Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–6
User Flash Memory Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–7
In-System Programming Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–7
Real-Time ISP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–8
Design Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–8
Programming with External Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–8
Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–9
Chapter 7. User Flash Memory in MAX V Devices
UFM Array Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–1
Memory Organization Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–2
Using and Accessing UFM Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–2
UFM Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–3
UFM Address Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–5
UFM Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–6
UFM Program/Erase Control Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–6
Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–7
Instantiating the Oscillator without the UFM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–7
UFM Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–8
Read/Stream Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–9
Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–10
Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–11
Programming and Reading the UFM with JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–12
Jam Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–12
Jam Players . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–12
Software Support for UFM Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–13
Inter-Integrated Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–13
I2C Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–13
Device Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–15
Byte Write Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–16
Page Write Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–17
Acknowledge Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–17
Write Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–17
Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–17
Read Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–20
ALTUFM_I2C Interface Timing Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–22
Instantiating the I2C Interface Using the Quartus II ALTUFM_I2C Megafunction . . . . . . . . . . . 7–23
Serial Peripheral Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–23
Opcodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–25
ALTUFM SPI Timing Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–35
Instantiating SPI Using Quartus II ALTUFM_SPI Megafunction . . . . . . . . . . . . . . . . . . . . . . . . . 7–35
Parallel Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–36
ALTUFM Parallel Interface Timing Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–37
Instantiating Parallel Interface Using Quartus II ALTUFM_PARALLEL Megafunction . . . . . . 7–37
None (Altera Serial Interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–38
Instantiating None Using Quartus II ALTUFM_NONE Megafunction . . . . . . . . . . . . . . . . . . . . 7–38
Creating Memory Content File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–39
Memory Initialization for the ALTUFM_PARALLEL Megafunction . . . . . . . . . . . . . . . . . . . . . . 7–39
Memory Initialization for the ALTUFM_SPI Megafunction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–39
Memory Initialization for the ALTUFM_I2C Megafunction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–40
Simulation Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–43
Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–43
May 2011
Altera Corporation
MAX V Device Handbook
vi
Contents
Chapter 8. JTAG Boundary-Scan Testing in MAX V Devices
IEEE Std. 1149.1 BST Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–2
IEEE Std. 1149.1 Boundary-Scan Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–3
Boundary-Scan Cells of a MAX V Device I/O Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–4
JTAG Pins and Power Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–5
IEEE Std. 1149.1 BST Operation Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–6
SAMPLE/PRELOAD Instruction Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–8
EXTEST Instruction Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–10
BYPASS Instruction Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–12
IDCODE Instruction Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–12
USERCODE Instruction Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–13
CLAMP Instruction Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–13
HIGHZ Instruction Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–13
I/O Voltage Support in the JTAG Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–13
Boundary-Scan Test for Programmed Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–14
Disabling IEEE Std. 1149.1 BST Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–15
Guidelines for IEEE Std. 1149.1 Boundary-Scan Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–15
Boundary-Scan Description Language Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–15
Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–16
Additional Information
Document Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Info–1
How to Contact Altera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Info–1
Typographic Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Info–1
MAX V Device Handbook
May 2011
Altera Corporation
Section I. MAX V Device Core
This section provides a complete overview of all features relating to the MAX® V
device family.
This section includes the following chapters:
May 2011
■
Chapter 1, MAX V Device Family Overview
■
Chapter 2, MAX V Architecture
■
Chapter 3, DC and Switching Characteristics for MAX V Devices
Altera Corporation
MAX V Device Handbook
I–2
Section I: MAX V Device Core
MAX V Device Handbook
May 2011
Altera Corporation
1. MAX V Device Family Overview
MV51001-1.2
The MAX® V family of low cost and low power CPLDs offer more density and I/Os
per footprint versus other CPLDs. Ranging in density from 40 to 2,210 logic elements
(LEs) (32 to 1,700 equivalent macrocells) and up to 271 I/Os, MAX V devices provide
programmable solutions for applications such as I/O expansion, bus and protocol
bridging, power monitoring and control, FPGA configuration, and analog IC
interface.
MAX V devices feature on-chip flash storage, internal oscillator, and memory
functionality. With up to 50% lower total power versus other CPLDs and requiring as
few as one power supply, MAX V CPLDs can help you meet your low power design
requirement.
This chapter contains the following sections:
■
“Feature Summary” on page 1–1
■
“Integrated Software Platform” on page 1–3
■
“Device Pin-Outs” on page 1–3
■
“Ordering Information” on page 1–4
Feature Summary
The following list summarizes the MAX V device family features:
■
Low-cost, low-power, and non-volatile CPLD architecture
■
Instant-on (0.5 ms or less) configuration time
■
Standby current as low as 25 µA and fast power-down/reset operation
■
Fast propagation delay and clock-to-output times
■
Internal oscillator
■
Emulated RSDS output support with a data rate of up to 200 Mbps
■
Emulated LVDS output support with a data rate of up to 304 Mbps
■
Four global clocks with two clocks available per logic array block (LAB)
■
User flash memory block up to 8 Kbits for non-volatile storage with up to 1000
read/write cycles
■
Single 1.8-V external supply for device core
■
MultiVolt I/O interface supporting 3.3-V, 2.5-V, 1.8-V, 1.5-V, and 1.2-V logic levels
■
Bus-friendly architecture including programmable slew rate, drive strength,
bus-hold, and programmable pull-up resistors
■
Schmitt triggers enabling noise tolerant inputs (programmable per pin)
© 2011 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.
and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at
www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but
reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
MAX V Device Handbook
May 2011
Subscribe
1–2
Chapter 1: MAX V Device Family Overview
Feature Summary
■
I/Os are fully compliant with the PCI-SIG® PCI Local Bus Specification, revision
2.2 for 3.3-V operation
■
Hot-socket compliant
■
Built-in JTAG BST circuitry compliant with IEEE Std. 1149.1-1990
Table 1–1 lists the MAX V family features.
Table 1–1. MAX V Family Features
Feature
5M40Z
5M80Z
5M160Z
5M240Z
5M570Z
5M1270Z
5M2210Z
LEs
40
80
160
240
570
1,270
2,210
Typical Equivalent Macrocells
32
64
128
192
440
980
1,700
User Flash Memory Size (bits)
8,192
8,192
8,192
8,192
8,192
8,192
8,192
Global Clocks
4
4
4
4
4
4
4
Internal Oscillator
1
1
1
1
1
1
1
Maximum User I/O pins
54
79
79
114
159
271
271
tPD1 (ns) (1)
7.5
7.5
7.5
7.5
9.0
6.2
7.0
fCNT (MHz) (2)
152
152
152
152
152
304
304
tSU (ns)
2.3
2.3
2.3
2.3
2.2
1.2
1.2
tCO (ns)
6.5
6.5
6.5
6.5
6.7
4.6
4.6
Notes to Table 1–1:
(1) tPD1 represents a pin-to-pin delay for the worst case I/O placement with a full diagonal path across the device and combinational logic
implemented in a single LUT and LAB that is adjacent to the output pin.
(2) The maximum global clock frequency, fCNT, is limited by the I/O standard on the clock input pin. The 16-bit counter critical delay will run faster
than this number.
MAX V devices accept 1.8 V on their VCCINT pins. The 1.8-V VCCINT external supply
powers the device core directly. MAX V devices operate internally at 1.8 V. The
supported MultiVolt I/O interface voltage levels (VCCIO) are 1.2 V, 1.5 V, 1.8 V, 2.5 V,
and 3.3 V.
MAX V devices are available in two speed grades: –4 and –5, with –4 being the fastest.
For commercial applications, speed grades –C4 and –C5 are available. For industrial
and automotive applications, speed grade –I5 and –A5 are available, respectively.
These speed grades represent the overall relative performance, not any specific timing
parameter.
f For propagation delay timing numbers within each speed grade and density, refer to
the DC and Switching Characteristics for MAX V Devices chapter.
MAX V devices are available in space-saving FineLine BGA (FBGA), Micro FineLine
BGA (MBGA), plastic enhanced quad flat pack (EQFP), and thin quad flat pack
(TQFP) packages (refer to Table 1–2 and Table 1–3). MAX V devices support vertical
migration within the same package (for example, you can migrate between the
5M570Z, 5M1270Z, and 5M2210Z devices in the 256-pin FineLine BGA package).
Vertical migration means that you can migrate to devices whose dedicated pins and
JTAG pins are the same and power pins are subsets or supersets for a given package
across device densities. The largest density in any package has the highest number of
power pins; you must lay out for the largest planned density in a package to provide
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 1: MAX V Device Family Overview
Integrated Software Platform
1–3
the necessary power pins for migration. For I/O pin migration across densities, cross
reference the available I/O pins using the device pin-outs for all planned densities of
a given package type to identify which I/O pins can be migrated. The Quartus® II
software can automatically cross-reference and place all pins for you when given a
device migration list.
Table 1–2. MAX V Packages and User I/O Pins (Note 1)
64-Pin
MBGA
64-Pin
EQFP
68-Pin
MBGA
100-Pin
TQFP
100-Pin
MBGA
144-Pin
TQFP
256-Pin
FBGA
324-Pin
FBGA
5M40Z
30
54
—
—
—
—
—
—
5M80Z
30
54
52
79
—
—
—
—
5M160Z
—
54
52
79
79
—
—
—
5M240Z
—
—
52
79
79
114
—
—
5M570Z
—
—
—
74
74
114
159
—
5M1270Z
—
—
—
—
—
114
211
271
5M2210Z
—
—
—
—
—
—
203
271
Device
Note to Table 1–2:
(1) Device packages under the same arrow sign have vertical migration capability.
Table 1–3. MAX V Package Sizes
Package
Pitch (mm)
Area
(mm2)
Length × width
(mm × mm)
64-Pin
MBGA
64-Pin
EQFP
68-Pin
MBGA
100-Pin
TQFP
100-Pin
MBGA
144-Pin
TQFP
256-Pin
FBGA
324-Pin
FBGA
0.5
0.4
0.5
0.5
0.5
0.5
1
1
20.25
81
25
256
36
484
289
361
4.5 × 4.5
9×9
5×5
16 × 16
6×6
22 × 22
17 × 17
19 × 19
Integrated Software Platform
The Quartus II software provides an integrated environment for HDL and schematic
design entry, compilation and logic synthesis, full simulation and advanced timing
analysis, and programming of MAX V devices.
f For more information about the Quartus II software features, refer to the Quartus II
Handbook.
You can debug your MAX V designs using In-System Sources and Probes Editor in
the Quartus II software. This feature allows you to easily control any internal signal
and provides you with a completely dynamic debugging environment.
f For more information about the In-System Sources and Probes Editor, refer to the
Design Debugging Using In-System Sources and Probes chapter of the Quartus II
Handbook.
Device Pin-Outs
f For more information, refer to the MAX V Device Pin-Out Files page.
May 2011
Altera Corporation
MAX V Device Handbook
1–4
Chapter 1: MAX V Device Family Overview
Ordering Information
Ordering Information
Figure 1–1 shows the ordering codes for MAX V devices.
Figure 1–1. MAX V Device Packaging Ordering Information
5M
40Z
E
64
C
4
N
Family Signature
5M:
Optional Suffix
MAX V
Indicates specific device
options or shipment method
N: Lead-free packaging
Device Type
40Z:
80Z:
160Z:
240Z:
570Z:
1270Z:
2210Z:
Speed Grade
40 Logic Elements
80 Logic Elements
160 Logic Elements
240 Logic Elements
570 Logic Elements
1,270 Logic Elements
2,210 Logic Elements
4 or 5, with 4 being the fastest
Operating Temperature
C: Commercial temperature (TJ = 0° C to 85° C)
I: Industrial temperature (TJ = -40° C to 100° C)
A: Automotive temperature (TJ = -40° C to 125° C)
Package Type
T:
F:
M:
E:
Thin quad flat pack (TQFP)
FineLine BGA (FBGA)
Micro FineLine BGA (MBGA)
Plastic Enhanced Quad Flat Pack (EQFP)
Pin Count
Number of pins for a particular package
Document Revision History
Table 1–4 lists the revision history for this chapter.
Table 1–4. Document Revision History
Date
Version
Changes
■
Updated Figure 1–1.
■
Updated Table 1–3.
May 2011
1.2
January 2011
1.1
Updated “Feature Summary” section.
December 2010
1.0
Initial release.
MAX V Device Handbook
May 2011
Altera Corporation
2. MAX V Architecture
MV51002-1.0
This chapter describes the architecture of the MAX ® V device and contains the
following sections:
■
“Functional Description” on page 2–1
■
“Logic Array Blocks” on page 2–4
■
“Logic Elements” on page 2–8
■
“MultiTrack Interconnect” on page 2–14
■
“Global Signals” on page 2–19
■
“User Flash Memory Block” on page 2–21
■
“Internal Oscillator” on page 2–22
■
“Core Voltage” on page 2–25
■
“I/O Structure” on page 2–26
Functional Description
MAX V devices contain a two-dimensional row- and column-based architecture to
implement custom logic. Row and column interconnects provide signal interconnects
between the logic array blocks (LABs).
Each LAB in the logic array contains 10 logic elements (LEs). An LE is a small unit of
logic that provides efficient implementation of user logic functions. LABs are grouped
into rows and columns across the device. The MultiTrack interconnect provides fast
granular timing delays between LABs. The fast routing between LEs provides
minimum timing delay for added levels of logic versus globally routed interconnect
structures.
The I/O elements (IOEs) located after the LAB rows and columns around the
periphery of the MAX V device feeds the I/O pins. Each IOE contains a bidirectional
I/O buffer with several advanced features. I/O pins support Schmitt trigger inputs
and various single-ended standards, such as 33-MHz, 32-bit PCI™, and LVTTL.
MAX V devices provide a global clock network. The global clock network consists of
four global clock lines that drive throughout the entire device, providing clocks for all
resources within the device. You can also use the global clock lines for control signals
such as clear, preset, or output enable.
© 2010 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.
and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at
www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but
reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
MAX V Device Handbook
December 2010
Subscribe
2–2
Chapter 2: MAX V Architecture
Functional Description
Figure 2–1 shows a functional block diagram of the MAX V device.
Figure 2–1. Device Block Diagram
IOE
IOE
IOE
IOE
IOE
IOE
IOE
Logic
Element
Logic
Element
Logic
Element
IOE
Logic
Element
Logic
Element
Logic
Element
IOE
Logic
Element
Logic
Element
Logic
Element
IOE
Logic
Element
Logic
Element
Logic
Element
Logic Array
BLock (LAB)
MultiTrack
Interconnect
MultiTrack
Interconnect
Each MAX V device contains a flash memory block within its floorplan. This block is
located on the left side of the 5M40Z, 5M80Z, 5M160Z, and 5M240Z devices. On the
5M240Z (T144 package), 5M570Z, 5M1270Z, and 5M2210Z devices, the flash memory
block is located on the bottom-left area of the device. The majority of this flash
memory storage is partitioned as the dedicated configuration flash memory (CFM)
block. The CFM block provides the non-volatile storage for all of the SRAM
configuration information. The CFM automatically downloads and configures the
logic and I/O at power-up, providing instant-on operation.
f For more information about configuration upon power-up, refer to the Hot Socketing
and Power-On Reset for MAX V Devices chapter.
A portion of the flash memory within the MAX V device is partitioned into a small
block for user data. This user flash memory (UFM) block provides 8,192 bits of
general-purpose user storage. The UFM provides programmable port connections to
the logic array for reading and writing. There are three LAB rows adjacent to this
block, with column numbers varying by device.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
Functional Description
2–3
Table 2–1 lists the number of LAB rows and columns in each device, as well as the
number of LAB rows and columns adjacent to the flash memory area. The long LAB
rows are full LAB rows that extend from one side of row I/O blocks to the other. The
short LAB rows are adjacent to the UFM block; their length is shown as width in LAB
columns.
Table 2–1. Device Resources for MAX V Devices
LAB Rows
Device
UFM Blocks
LAB Columns
Total LABs
Long LAB Rows
Short LAB Rows (Width) (1)
5M40Z
1
6
4
—
24
5M80Z
1
6
4
—
24
5M160Z
1
6
4
—
24
5M240Z (2)
1
6
4
—
24
5M240Z (3)
1
12
4
3 (3)
57
5M570Z
1
12
4
3 (3)
57
5M1270Z (4)
1
16
7
3 (5)
127
5M1270Z (5)
1
20
10
3 (7)
221
5M2210Z
1
20
10
3 (7)
221
Notes to Table 2–1:
(1)
(2)
(3)
(4)
(5)
The width is the number of LAB columns in length.
Not applicable to T144 package of the 5M240Z device.
Only applicable to T144 package of the 5M240Z device.
Not applicable to F324 package of the 5M1270Z device.
Only applicable to F324 package of the 5M1270Z device.
December 2010
Altera Corporation
MAX V Device Handbook
2–4
Chapter 2: MAX V Architecture
Logic Array Blocks
Figure 2–2 shows a floorplan of a MAX V device.
Figure 2–2. Device Floorplan for MAX V Devices (Note 1)
I/O Blocks
I/O Blocks
Logic Array
Blocks
Logic Array
Blocks
2 GCLK
Inputs
2 GCLK
Inputs
I/O Blocks
UFM Block
CFM Block
Note to Figure 2–2:
(1) The device shown is a 5M570Z device. 5M1270Z and 5M2210Z devices have a similar floorplan with more LABs. For 5M40Z, 5M80Z, 5M160Z,
and 5M240Z devices, the CFM and UFM blocks are located on the left side of the device.
Logic Array Blocks
Each LAB consists of 10 LEs, LE carry chains, LAB control signals, a local interconnect,
a look-up table (LUT) chain, and register chain connection lines. There are 26 possible
unique inputs into an LAB, with an additional 10 local feedback input lines fed by LE
outputs in the same LAB. The local interconnect transfers signals between LEs in the
same LAB. LUT chain connections transfer the LUT output from one LE to the
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
Logic Array Blocks
2–5
adjacent LE for fast sequential LUT connections within the same LAB. Register chain
connections transfer the output of one LE’s register to the adjacent LE’s register
within an LAB. The Quartus ® II software places associated logic within an LAB or
adjacent LABs, allowing the use of local, LUT chain, and register chain connections
for performance and area efficiency. Figure 2–3 shows the MAX V LAB.
Figure 2–3. LAB Structure for MAX V Devices
Row Interconnect
Column Interconnect
LE0
Fast I/O connection
to IOE (1)
Fast I/O connection
to IOE (1)
LE1
DirectLink
interconnect from
adjacent LAB
or IOE
LE2
DirectLink
interconnect from
adjacent LAB
or IOE
LE3
LE4
LE5
LE6
DirectLink
interconnect to
adjacent LAB
or IOE
DirectLink
interconnect to
adjacent LAB
or IOE
LE7
LE8
LE9
Logic Element
LAB
Local Interconnect
Note to Figure 2–3:
(1) Only from LABs adjacent to IOEs.
December 2010
Altera Corporation
MAX V Device Handbook
2–6
Chapter 2: MAX V Architecture
Logic Array Blocks
LAB Interconnects
Column and row interconnects and LE outputs within the same LAB drive the LAB
local interconnect. Adjacent LABs, from the left and right, can also drive an LAB’s
local interconnect through the DirectLink connection. The DirectLink connection
feature minimizes the use of row and column interconnects, providing higher
performance and flexibility. Each LE can drive 30 other LEs through fast local and
DirectLink interconnects. Figure 2–4 shows the DirectLink connection.
Figure 2–4. DirectLink Connection
DirectLink interconnect from
right LAB or IOE output
DirectLink interconnect from
left LAB or IOE output
LE0
LE1
LE2
LE3
LE4
LE5
DirectLink
interconnect
to left
LE6
DirectLink
interconnect
to right
LE7
Local
Interconnect
LE8
LE9
Logic Element
LAB
LAB Control Signals
Each LAB contains dedicated logic for driving control signals to its LEs. The control
signals include two clocks, two clock enables, two asynchronous clears, a
synchronous clear, an asynchronous preset/load, a synchronous load, and
add/subtract control signals, providing a maximum of 10 control signals at a time.
Synchronous load and clear signals are generally used when implementing counters
but they can also be used with other functions.
Each LAB can use two clocks and two clock enable signals. Each LAB’s clock and
clock enable signals are linked. For example, any LE in a particular LAB using the
labclk1 signal also uses labclkena1. If the LAB uses both the rising and falling edges
of a clock, it also uses both LAB-wide clock signals. Deasserting the clock enable
signal turns off the LAB-wide clock.
Each LAB can use two asynchronous clear signals and an asynchronous load/preset
signal. By default, the Quartus II software uses a NOT gate push-back technique to
achieve preset. If you disable the NOT gate push-back option or assign a given register
to power-up high using the Quartus II software, the preset is then achieved using the
asynchronous load signal with asynchronous load data input tied high.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
Logic Array Blocks
2–7
With the LAB-wide addnsub control signal, a single LE can implement a one-bit adder
and subtractor. This signal saves LE resources and improves performance for logic
functions such as correlators and signed multipliers that alternate between addition
and subtraction depending on data.
The LAB column clocks [3..0], driven by the global clock network, and LAB local
interconnect generate the LAB-wide control signals. The MultiTrack interconnect
structure drives the LAB local interconnect for non-global control signal generation.
The MultiTrack interconnect’s inherent low skew allows clock and control signal
distribution in addition to data signals. Figure 2–5 shows the LAB control signal
generation circuit.
Figure 2–5. LAB-Wide Control Signals
Dedicated
LAB Column
Clocks
4
Local
Interconnect
Local
Interconnect
Local
Interconnect
Local
Interconnect
Local
Interconnect
Local
Interconnect
December 2010
labclkena2
labclkena1
labclk1
Altera Corporation
labclk2
labclr2
syncload
asyncload
or labpre
labclr1
addnsub
synclr
MAX V Device Handbook
2–8
Chapter 2: MAX V Architecture
Logic Elements
Logic Elements
The smallest unit of logic in the MAX V architecture, the LE, is compact and provides
advanced features with efficient logic utilization. Each LE contains a four-input LUT,
which is a function generator that can implement any function of four variables. In
addition, each LE contains a programmable register and carry chain with carry-select
capability. A single LE also supports dynamic single-bit addition or subtraction mode
that is selected by an LAB-wide control signal. Each LE drives all types of
interconnects: local, row, column, LUT chain, register chain, and DirectLink
interconnects as shown in Figure 2–6.
Figure 2–6. LE for MAX V Devices
Register chain
routing from
previous LE
LAB-wide
Register Bypass
Synchronous
Load
LAB-wide
Packed
Synchronous
Register Select
Clear
LAB Carry-In
addnsub
Carry-In1
Carry-In0
Programmable
Register
LUT chain
routing to next LE
data1
data2
data3
Look-Up
Table
(LUT)
Carry
Chain
Synchronous
Load and
Clear Logic
Row, column,
and DirectLink
routing
PRN/ALD
D
Q
ADATA
data4
ENA
CLRN
labclr1
labclr2
labpre/aload
Chip-Wide
Reset (DEV_CLRn)
Row, column,
and DirectLink
routing
Asynchronous
Clear/Preset/
Load Logic
Local routing
Register chain
output
Register
Feedback
Clock and
Clock Enable
Select
labclk1
labclk2
labclkena1
labclkena2
Carry-Out0
Carry-Out1
LAB Carry-Out
You can configure each LE’s programmable register for D, T, JK, or SR operation. Each
register has data, true asynchronous load data, clock, clock enable, clear, and
asynchronous load/preset inputs. Global signals, general purpose I/O (GPIO) pins,
or any LE can drive the register ’s clock and clear control signals. Either GPIO pins or
LEs can drive the clock enable, preset, asynchronous load, and asynchronous data.
The asynchronous load data input comes from the data3 input of the LE. For
combinational functions, the LUT output bypasses the register and drives directly to
the LE outputs.
Each LE has three outputs that drive the local, row, and column routing resources. The
LUT or register output can drive these three outputs independently. Two LE outputs
drive either a column or row and DirectLink routing connections while one output
drives the local interconnect resources. This configuration allows the LUT to drive one
output while the register drives another output. This register packing feature
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
Logic Elements
2–9
improves device utilization because the device can use the register and the LUT for
unrelated functions. Another special packing mode allows the register output to feed
back into the LUT of the same LE so that the register is packed with its own fan-out
LUT. This mode provides another mechanism for improved fitting. The LE can also
drive out registered and unregistered versions of the LUT output.
LUT Chain and Register Chain
In addition to the three general routing outputs, the LEs within a LAB have LUT chain
and register chain outputs. LUT chain connections allow LUTs within the same LAB
to cascade together for wide input functions. Register chain outputs allow registers
within the same LAB to cascade together. The register chain output allows a LAB to
use LUTs for a single combinational function and the registers for an unrelated shift
register implementation. These resources speed up connections between LABs while
saving local interconnect resources. For more information about LUT chain and
register chain connections, refer to “MultiTrack Interconnect” on page 2–14.
addnsub Signal
The LE’s dynamic adder/subtractor feature saves logic resources by using one set of
LEs to implement both an adder and a subtractor. This feature is controlled by the
LAB-wide control signal addnsub. The addnsub signal sets the LAB to perform either
A + B or A – B. The LUT computes addition; subtraction is computed by adding the
two’s complement of the intended subtractor. The LAB-wide signal converts to two’s
complement by inverting the B bits within the LAB and setting carry-in to 1, which
adds one to the LSB. The LSB of an adder/subtractor must be placed in the first LE of
the LAB, where the LAB-wide addnsub signal automatically sets the carry-in to 1. The
Quartus II Compiler automatically places and uses the adder/subtractor feature
when using adder/subtractor parameterized functions.
LE Operating Modes
The MAX V LE can operate in one of the following modes:
■
“Normal Mode”
■
“Dynamic Arithmetic Mode”
Each mode uses LE resources differently. In each mode, eight available inputs to the
LE, the four data inputs from the LAB local interconnect, carry-in0 and carry-in1
from the previous LE, the LAB carry-in from the previous carry-chain LAB, and the
register chain connection are directed to different destinations to implement the
desired logic function. LAB-wide signals provide clock, asynchronous clear,
asynchronous preset/load, synchronous clear, synchronous load, and clock enable
control for the register. These LAB-wide signals are available in all LE modes. The
addnsub control signal is allowed in arithmetic mode.
The Quartus II software, along with parameterized functions such as the library of
parameterized modules (LPM) functions, automatically chooses the appropriate
mode for common functions such as counters, adders, subtractors, and arithmetic
functions.
December 2010
Altera Corporation
MAX V Device Handbook
2–10
Chapter 2: MAX V Architecture
Logic Elements
Normal Mode
The normal mode is suitable for general logic applications and combinational
functions. In normal mode, four data inputs from the LAB local interconnect are
inputs to a four-input LUT as shown in Figure 2–7. The Quartus II Compiler
automatically selects the carry-in or the data3 signal as one of the inputs to the LUT.
Each LE can use LUT chain connections to drive its combinational output directly to
the next LE in the LAB. Asynchronous load data for the register comes from the data3
input of the LE. LEs in normal mode support packed registers.
Figure 2–7. LE in Normal Mode
sload
sclear
(LAB Wide) (LAB Wide)
aload
(LAB Wide)
Register chain
connection
addnsub (LAB Wide)
(1)
data1
data2
data3
cin (from cout
of previous LE)
4-Input
LUT
clock (LAB Wide)
ena (LAB Wide)
data4
aclr (LAB Wide)
Register Feedback
ALD/PRE
ADATA Q
D
Row, column, and
DirectLink routing
ENA
CLRN
Row, column, and
DirectLink routing
Local routing
LUT chain
connection
Register
chain output
Note to Figure 2–7:
(1) This signal is only allowed in normal mode if the LE is after an adder/subtractor chain.
Dynamic Arithmetic Mode
The dynamic arithmetic mode is ideal for implementing adders, counters,
accumulators, wide parity functions, and comparators. A LE in dynamic arithmetic
mode uses four 2-input LUTs configurable as a dynamic adder/subtractor. The first
two 2-input LUTs compute two summations based on a possible carry-in of 1 or 0; the
other two LUTs generate carry outputs for the two chains of the carry-select circuitry.
As shown in Figure 2–8, the LAB carry-in signal selects either the carry-in0 or
carry-in1 chain. The selected chain’s logic level in turn determines which parallel
sum is generated as a combinational or registered output. For example, when
implementing an adder, the sum output is the selection of two possible calculated
sums:
data1 + data2 + carry-in0
or
data1 + data2 + carry-in1
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
Logic Elements
2–11
The other two LUTs use the data1 and data2 signals to generate two possible
carry-out signals: one for a carry of 1 and the other for a carry of 0. The carry-in0
signal acts as the carry-select for the carry-out0 output and carry-in1 acts as the
carry-select for the carry-out1 output. LEs in arithmetic mode can drive out
registered and unregistered versions of the LUT output.
The dynamic arithmetic mode also offers clock enable, counter enable, synchronous
up/down control, synchronous clear, synchronous load, and dynamic
adder/subtractor options. The LAB local interconnect data inputs generate the
counter enable and synchronous up/down control signals. The synchronous clear
and synchronous load options are LAB-wide signals that affect all registers in the
LAB. The Quartus II software automatically places any registers that are not used by
the counter into other LABs. The addnsub LAB-wide signal controls whether the LE
acts as an adder or subtractor.
Figure 2–8. LE in Dynamic Arithmetic Mode
LAB Carry-In
sload
sclear
(LAB Wide) (LAB Wide)
Register chain
connection
Carry-In0
Carry-In1
addnsub
(LAB Wide)
(1)
data1
data2
data3
LUT
LUT
LUT
aload
(LAB Wide)
ALD/PRE
ADATA Q
D
Row, column, and
direct link routing
ENA
CLRN
Row, column, and
direct link routing
clock (LAB Wide)
ena (LAB Wide)
Local routing
aclr (LAB Wide)
LUT chain
connection
LUT
Register
chain output
Register Feedback
Carry-Out0 Carry-Out1
Note to Figure 2–8:
(1) The addnsub signal is tied to the carry input for the first LE of a carry chain only.
Carry-Select Chain
The carry-select chain provides a very fast carry-select function between LEs in
dynamic arithmetic mode. The carry-select chain uses the redundant carry calculation
to increase the speed of carry functions. The LE is configured to calculate outputs for a
possible carry-in of 0 and carry-in of 1 in parallel. The carry-in0 and carry-in1
signals from a lower-order bit feed forward into the higher-order bit via the parallel
carry chain and feed into both the LUT and the next portion of the carry chain.
Carry-select chains can begin in any LE within an LAB.
December 2010
Altera Corporation
MAX V Device Handbook
2–12
Chapter 2: MAX V Architecture
Logic Elements
The speed advantage of the carry-select chain is in the parallel pre-computation of
carry chains. Because the LAB carry-in selects the precomputed carry chain, not every
LE is in the critical path. Only the propagation delays between LAB carry-in
generation (LE5 and LE10) are now part of the critical path. This feature allows the
MAX V architecture to implement high-speed counters, adders, multipliers, parity
functions, and comparators of arbitrary width.
Figure 2–9 shows the carry-select circuitry in an LAB for a 10-bit full adder. One
portion of the LUT generates the sum of two bits using the input signals and the
appropriate carry-in bit; the sum is routed to the output of the LE. The register can be
bypassed for simple adders or used for accumulator functions. Another portion of the
LUT generates carry-out bits. An LAB-wide carry-in bit selects which chain is used for
the addition of given inputs. The carry-in signal for each chain, carry-in0 or
carry-in1, selects the carry-out to carry forward to the carry-in signal of the
next-higher-order bit. The final carry-out signal is routed to an LE, where it is fed to
local, row, or column interconnects.
Figure 2–9. Carry-Select Chain
LAB Carry-In
0
1
A1
B1
LE0
A2
B2
LE1
LAB Carry-In
Sum1
Carry-In0
Carry-In1
A3
B3
LE2
A4
B4
LE3
A5
B5
LE4
0
Sum2
LUT
data1
data2
Sum3
Sum
LUT
Sum4
LUT
Sum5
LUT
1
A6
B6
LE5
A7
B7
LE6
A8
B8
LE7
A9
B9
LE8
A10
B10
LE9
Carry-Out0
Sum6
Carry-Out1
Sum7
Sum8
Sum9
Sum10
To top of adjacent LAB
LAB Carry-Out
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
Logic Elements
2–13
The Quartus II software automatically creates carry chain logic during design
processing, or you can create it manually during design entry. Parameterized
functions such as LPM functions automatically take advantage of carry chains for the
appropriate functions. The Quartus II software creates carry chains longer than 10 LEs
by linking adjacent LABs within the same row together automatically. A carry chain
can extend horizontally up to one full LAB row, but does not extend between LAB
rows.
Clear and Preset Logic Control
LAB-wide signals control the logic for the register ’s clear and preset signals. The LE
directly supports an asynchronous clear and preset function. The register preset is
achieved through the asynchronous load of a logic high. MAX V devices support
simultaneous preset/asynchronous load and clear signals. An asynchronous clear
signal takes precedence if both signals are asserted simultaneously. Each LAB
supports up to two clears and one preset signal.
In addition to the clear and preset ports, MAX V devices provide a chip-wide reset pin
(DEV_CLRn) that resets all registers in the device. An option set before compilation in
the Quartus II software controls this pin. This chip-wide reset overrides all other
control signals and uses its own dedicated routing resources without using any of the
four global resources. Driving this signal low before or during power-up prevents
user mode from releasing clears within the design. This allows you to control when
clear is released on a device that has just been powered-up. If not set for its chip-wide
reset function, the DEV_CLRn pin is a regular I/O pin.
By default, all registers in MAX V devices are set to power-up low. However, this
power-up state can be set to high on individual registers during design entry using
the Quartus II software.
LE RAM
The Quartus II memory compiler can configure the unused LEs as LE RAM.
MAX V devices support the following memory types:
■
FIFO synchronous R/W
■
FIFO asynchronous R/W
■
1 port SRAM
■
2 port SRAM
■
3 port SRAM
■
shift registers
f For more information about memory, refer to the Internal Memory (RAM and ROM)
User Guide.
December 2010
Altera Corporation
MAX V Device Handbook
2–14
Chapter 2: MAX V Architecture
MultiTrack Interconnect
MultiTrack Interconnect
In the MAX V architecture, connections between LEs, the UFM, and device I/O pins
are provided by the MultiTrack interconnect structure. The MultiTrack interconnect
consists of continuous, performance-optimized routing lines used for inter- and
intra-design block connectivity. The Quartus II Compiler automatically places critical
design paths on faster interconnects to improve design performance.
The MultiTrack interconnect consists of row and column interconnects that span fixed
distances. A routing structure with fixed length resources for all devices allows
predictable and short delays between logic levels instead of large delays associated
with global or long routing lines. Dedicated row interconnects route signals to and
from LABs within the same row. These row resources include:
■
DirectLink interconnects between LABs
■
R4 interconnects traversing four LABs to the right or left
The DirectLink interconnect allows an LAB to drive into the local interconnect of its
left and right neighbors. The DirectLink interconnect provides fast communication
between adjacent LABs and blocks without using row interconnect resources.
The R4 interconnects span four LABs and are used for fast row connections in a
four-LAB region. Every LAB has its own set of R4 interconnects to drive either left or
right. Figure 2–10 shows R4 interconnect connections from an LAB. R4 interconnects
can drive and be driven by row IOEs. For LAB interfacing, a primary LAB or
horizontal LAB neighbor can drive a given R4 interconnect. For R4 interconnects that
drive to the right, the primary LAB and right neighbor can drive on to the
interconnect. For R4 interconnects that drive to the left, the primary LAB and its left
neighbor can drive on to the interconnect. R4 interconnects can drive other R4
interconnects to extend the range of LABs they can drive. R4 interconnects can also
drive C4 interconnects for connections from one row to another.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
MultiTrack Interconnect
2–15
Figure 2–10. R4 Interconnect Connections
Adjacent LAB can
drive onto another
LAB’s R4 Interconnect
C4 Column Interconnects (1)
R4 Interconnect
Driving Right
R4 Interconnect
Driving Left
LAB
Neighbor
Primary
LAB (2)
LAB
Neighbor
Notes to Figure 2–10:
(1) C4 interconnects can drive R4 interconnects.
(2) This pattern is repeated for every LAB in the LAB row.
The column interconnect operates similarly to the row interconnect. Each column of
LABs is served by a dedicated column interconnect, which vertically routes signals to
and from LABs and row and column IOEs. These column resources include:
■
LUT chain interconnects within an LAB
■
Register chain interconnects within an LAB
■
C4 interconnects traversing a distance of four LABs in an up and down direction
MAX V devices include an enhanced interconnect structure within LABs for routing
LE output to LE input connections faster using LUT chain connections and register
chain connections. The LUT chain connection allows the combinational output of an
LE to directly drive the fast input of the LE right below it, bypassing the local
interconnect. These resources can be used as a high-speed connection for wide fan-in
functions from LE 1 to LE 10 in the same LAB. The register chain connection allows
the register output of one LE to connect directly to the register input of the next LE in
the LAB for fast shift registers. The Quartus II Compiler automatically takes
advantage of these resources to improve utilization and performance. Figure 2–11
shows the LUT chain and register chain interconnects.
December 2010
Altera Corporation
MAX V Device Handbook
2–16
Chapter 2: MAX V Architecture
MultiTrack Interconnect
Figure 2–11. LUT Chain and Register Chain Interconnects
Local Interconnect
Routing Among LEs
in the LAB
LUT Chain
Routing to
Adjacent LE
LE0
Register Chain
Routing to Adjacent
LE's Register Input
LE1
Local
Interconnect
LE2
LE3
LE4
LE5
LE6
LE7
LE8
LE9
The C4 interconnects span four LABs up or down from a source LAB. Every LAB has
its own set of C4 interconnects to drive either up or down. Figure 2–12 shows the C4
interconnect connections from an LAB in a column. The C4 interconnects can drive
and be driven by column and row IOEs. For LAB interconnection, a primary LAB or
its vertical LAB neighbor can drive a given C4 interconnect. C4 interconnects can
drive each other to extend their range as well as drive row interconnects for
column-to-column connections.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
MultiTrack Interconnect
2–17
Figure 2–12. C4 Interconnect Connections (Note 1)
C4 Interconnect
Drives Local and R4
Interconnects
Up to Four Rows
C4 Interconnect
Driving Up
LAB
Row
Interconnect
Adjacent LAB can
drive onto neighboring
LAB's C4 interconnect
Local
Interconnect
C4 Interconnect
Driving Down
Note to Figure 2–12:
(1) Each C4 interconnect can drive either up or down four rows.
December 2010
Altera Corporation
MAX V Device Handbook
2–18
Chapter 2: MAX V Architecture
MultiTrack Interconnect
The UFM block communicates with the logic array similar to LAB-to-LAB interfaces.
The UFM block connects to row and column interconnects and has local interconnect
regions driven by row and column interconnects. This block also has DirectLink
interconnects for fast connections to and from a neighboring LAB. For more
information about the UFM interface to the logic array, refer too “User Flash Memory
Block” on page 2–21.
Table 2–2 lists the MAX V device routing scheme.
Table 2–2. Routing Scheme for MAX V Devices
Destination
Source
LUT
Chain
Register
Chain
Local
(1)
DirectLink
(1)
R4 (1)
C4 (1)
LE
UFM
Block
Column
IOE
Row
IOE
Fast I/O
(1)
LUT Chain
—
—
—
—
—
—
v
—
—
—
—
Register Chain
—
—
—
—
—
—
v
—
—
—
—
Local
Interconnect
—
—
—
—
—
—
v
v
v
v
—
DirectLink
Interconnect
—
—
v
—
—
—
—
—
—
—
—
R4 Interconnect
—
—
v
—
v
v
—
—
—
—
—
C4 Interconnect
—
—
v
—
v
v
—
—
—
—
—
LE
v
v
v
v
v
v
—
—
v
v
v
UFM Block
—
—
v
v
v
v
—
—
—
—
—
Column IOE
—
—
—
—
—
v
—
—
—
—
—
Row IOE
—
—
—
v
v
v
—
—
—
—
—
Note to Table 2–2:
(1) These categories are interconnects.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
Global Signals
2–19
Global Signals
Each MAX V device has four dual-purpose dedicated clock pins (GCLK[3..0], two
pins on the left side and two pins on the right side) that drive the global clock network
for clocking, as shown in Figure 2–13. These four pins can also be used as GPIOs if
they are not used to drive the global clock network.
The four global clock lines in the global clock network drive throughout the entire
device. The global clock network can provide clocks for all resources within the
device including LEs, LAB local interconnect, IOEs, and the UFM block. The global
clock lines can also be used for global control signals, such as clock enables,
synchronous or asynchronous clears, presets, output enables, or protocol control
signals such as TRDY and IRDY for the PCI I/O standard. Internal logic can drive the
global clock network for internally-generated global clocks and control signals.
Figure 2–13 shows the various sources that drive the global clock network.
Figure 2–13. Global Clock Generation
GCLK0
GCLK1
GCLK2
GCLK3
Logic Array(1)
4
4
Global Clock
Network
Note to Figure 2–13:
(1) Any I/O pin can use a MultiTrack interconnect to route as a logic array-generated global clock signal.
The global clock network drives to individual LAB column signals, LAB column
clocks [3..0], that span an entire LAB column from the top to the bottom of the
device. Unused global clocks or control signals in an LAB column are turned off at the
LAB column clock buffers shown in Figure 2–14. The LAB column clocks [3..0] are
multiplexed down to two LAB clock signals and one LAB clear signal. Other control
signal types route from the global clock network into the LAB local interconnect. For
more information, refer to “LAB Control Signals” on page 2–6.
December 2010
Altera Corporation
MAX V Device Handbook
2–20
Chapter 2: MAX V Architecture
Global Signals
Figure 2–14. Global Clock Network (Note 1)
LAB Column
clock[3..0]
I/O Block Region
4
4
4
4
4
4
4
4
LAB Column
clock[3..0]
I/O Block Region
UFM Block (2)
I/O Block Region
CFM Block
Notes to Figure 2–14:
(1) LAB column clocks in I/O block regions provide high fan-out output enable signals.
(2) LAB column clocks drive to the UFM block.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
User Flash Memory Block
2–21
User Flash Memory Block
MAX V devices feature a single UFM block, which can be used like a serial EEPROM
for storing non-volatile information up to 8,192 bits. The UFM block connects to the
logic array through the MultiTrack interconnect, allowing any LE to interface to the
UFM block. Figure 2–15 shows the UFM block and interface signals. The logic array is
used to create customer interface or protocol logic to interface the UFM block data
outside of the device. The UFM block offers the following features:
■
Non-volatile storage up to 16-bit wide and 8,192 total bits
■
Two sectors for partitioned sector erase
■
Built-in internal oscillator that optionally drives logic array
■
Program, erase, and busy signals
■
Auto-increment addressing
■
Serial interface to logic array with programmable interface
Figure 2–15. UFM Block and Interface Signals
UFM Block
PROGRAM
Program
Erase
Control
ERASE
_: 4
OSC
OSC_ENA
9
RTP_BUSY
BUSY
OSC
UFM Sector 1
ARCLK
UFM Sector 0
Address
Register
16
16
ARSHFT
ARDin
DRDin
Data Register
DRDout
DRCLK
DRSHFT
December 2010
Altera Corporation
MAX V Device Handbook
2–22
Chapter 2: MAX V Architecture
User Flash Memory Block
UFM Storage
Each device stores up to 8,192 bits of data in the UFM block. Table 2–3 lists the data
size, sector, and address sizes for the UFM block.
Table 2–3. UFM Array Size
Device
Total Bits
Sectors
Address Bits
Data Width
5M40Z
8,192
2 (4,096 bits per sector)
9
16
5M80Z
8,192
2 (4,096 bits per sector)
9
16
5M160Z
8,192
2 (4,096 bits per sector)
9
16
5M240Z
8,192
2 (4,096 bits per sector)
9
16
5M570Z
8,192
2 (4,096 bits per sector)
9
16
5M1270Z
8,192
2 (4,096 bits per sector)
9
16
5M2210Z
8,192
2 (4,096 bits per sector)
9
16
There are 512 locations with 9-bit addressing ranging from 000h to 1FFh. The sector 0
address space is 000h to 0FFh and the sector 1 address space is from 100h to 1FFh. The
data width is up to 16 bits of data. The Quartus II software automatically creates logic
to accommodate smaller read or program data widths. Erasure of the UFM involves
individual sector erasing (that is, one erase of sector 0 and one erase of sector 1 is
required to erase the entire UFM block). Because sector erase is required before a
program or write operation, having two sectors enables a sector size of data to be left
untouched while the other sector is erased and programmed with new data.
Internal Oscillator
As shown in Figure 2–15, the dedicated circuitry within the UFM block contains an
oscillator. The dedicated circuitry uses this oscillator internally for its read and
program operations. This oscillator's divide by 4 output can drive out of the UFM
block as a logic interface clock source or for general-purpose logic clocking. The
typical OSC output signal frequency ranges from 3.9 to 5.3 MHz, and its exact
frequency of operation is not programmable.
The UFM internal oscillator can be instantiated using the MegaWizard ™ Plug-In
Manager. You can also use the MAX II/MAX V Oscillator megafunction to instantiate
the UFM oscillator without using the UFM memory block.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
User Flash Memory Block
2–23
Program, Erase, and Busy Signals
The UFM block’s dedicated circuitry automatically generates the necessary internal
program and erase algorithm after the PROGRAM or ERASE input signals have been
asserted. The PROGRAM or ERASE signal must be asserted until the busy signal deasserts,
indicating the UFM internal program or erase operation has completed. The UFM
block also supports JTAG as the interface for programming and reading.
f For more information about programming and erasing the UFM block, refer to the
User Flash Memory in MAX V Devices chapter.
Auto-Increment Addressing
The UFM block supports standard read or stream read operations. The stream read is
supported with an auto-increment address feature. Deasserting the ARSHIFT signal
while clocking the ARCLK signal increments the address register value to read
consecutive locations from the UFM array.
Serial Interface
The UFM block supports a serial interface with serial address and data signals. The
internal shift registers within the UFM block for address and data are 9 bits and 16 bits
wide, respectively. The Quartus II software automatically generates interface logic in
LEs for a parallel address and data interface to the UFM block. Other standard
protocol interfaces such as SPI are also automatically generated in LE logic by the
Quartus II software.
f For more information about the UFM interface signals and the Quartus II LE-based
alternate interfaces, refer to the User Flash Memory in MAX V Devices chapter.
December 2010
Altera Corporation
MAX V Device Handbook
2–24
Chapter 2: MAX V Architecture
User Flash Memory Block
UFM Block to Logic Array Interface
The UFM block is a small partition of the flash memory that contains the CFM block,
as shown in Figure 2–1 and Figure 2–2. The UFM block for the 5M40Z, 5M80Z,
5M160Z, and 5M240Z devices is located on the left side of the device adjacent to the
left most LAB column. The UFM blocks for the 5M570Z, 5M1270Z, and 5M2210Z
devices are located at the bottom left of the device. The UFM input and output signals
interface to all types of interconnects (R4 interconnect, C4 interconnect, and
DirectLink interconnect to/from adjacent LAB rows). The UFM signals can also be
driven from global clocks, GCLK[3..0]. The interface regions for the 5M40Z, 5M80Z,
5M160Z, and 5M240Z devices are shown in Figure 2–16. The interface regions for
5M570Z, 5M1270Z, and 5M2210Z devices are shown in Figure 2–17.
Figure 2–16. 5M40Z, 5M80Z, 5M160Z, and 5M240Z UFM Block LAB Row Interface (Note 1), (2)
CFM Block
UFM Block
LAB
PROGRAM
ERASE
OSC_ENA
LAB
RTP_BUSY
DRDin
DRCLK
DRSHFT
ARin
ARCLK
ARSHFT
DRDout
OSC
BUSY
LAB
Notes to Figure 2–16:
(1) The UFM block inputs and outputs can drive to and from all types of interconnects, not only DirectLink interconnects
from adjacent row LABs.
(2) Not applicable to the T144 package of the 5M240Z device.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
Core Voltage
2–25
Figure 2–17. 5M240Z, 5M570Z, 5M1270Z, and 5M2210Z UFM Block LAB Row Interface (Note 1)
CFM Block
RTP_BUSY
BUSY
OSC
DRDout
DRDin
DRDCLK
DRDSHFT
ARDin
PROGRAM
ERASE
OSC_ENA
ARCLK
ARSHFT
LAB
LAB
UFM Block
LAB
Note to Figure 2–17:
(1) Only applicable to the T144 package of the 5M240Z device.
Core Voltage
The MAX V architecture supports a 1.8-V core voltage on the VCCINT supply. You must
use a 1.8-V VCC external supply to power the VCCINT pins.
Figure 2–18. Core Voltage Feature in MAX V Devices
1.8-V on
VCCINT Pins
1.8-V Core
Voltage
MAX V Device
December 2010
Altera Corporation
MAX V Device Handbook
2–26
Chapter 2: MAX V Architecture
I/O Structure
I/O Structure
IOEs support many features, including:
■
LVTTL, LVCMOS, LVDS, and RSDS I/O standards
■
3.3-V, 32-bit, 33-MHz PCI compliance
■
JTAG boundary-scan test (BST) support
■
Programmable drive strength control
■
Weak pull-up resistors during power-up and in system programming
■
Slew-rate control
■
Tri-state buffers with individual output enable control
■
Bus-hold circuitry
■
Programmable pull-up resistors in user mode
■
Unique output enable per pin
■
Open-drain outputs
■
Schmitt trigger inputs
■
Fast I/O connection
■
Programmable input delay
MAX V device IOEs contain a bidirectional I/O buffer. Figure 2–19 shows the MAX V
IOE structure. Registers from adjacent LABs can drive to or be driven from the IOE’s
bidirectional I/O buffers. The Quartus II software automatically attempts to place
registers in the adjacent LAB with fast I/O connection to achieve the fastest possible
clock-to-output and registered output enable timing. When the fast input registers
option is enabled, the Quartus II software automatically routes the register to
guarantee zero hold time. You can set timing assignments in the Quartus II software
to achieve desired I/O timing.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
I/O Structure
2–27
Fast I/O Connection
A dedicated fast I/O connection from the adjacent LAB to the IOEs within an I/O
block provides faster output delays for clock-to-output and tPD propagation delays.
This connection exists for data output signals, not output enable signals or input
signals. Figure 2–20, Figure 2–21, and Figure 2–22 illustrate the fast I/O connection.
Figure 2–19. IOE Structure for MAX V Devices
Data_in Fast_out
Data_out
OE
DEV_OE
Optional
PCI Clamp (1)
VCCIO
VCCIO
Programmable
Pull-Up (2)
I/O Pin
Optional Bus-Hold
Circuit
Drive Strength Control
Open-Drain Output
Slew Control
Programmable
Input Delay
Optional Schmitt
Trigger Input
Notes to Figure 2–19:
(1) Available only in I/O bank 3 of 5M1270Z and 5M2210Z devices.
(2) The programmable pull-up resistor is active during power-up, in-system programming (ISP), and if the device is unprogrammed.
December 2010
Altera Corporation
MAX V Device Handbook
2–28
Chapter 2: MAX V Architecture
I/O Structure
I/O Blocks
The IOEs are located in I/O blocks around the periphery of the MAX V device. There
are up to seven IOEs per row I/O block and up to four IOEs per column I/O block.
Each column or row I/O block interfaces with its adjacent LAB and MultiTrack
interconnect to distribute signals throughout the device. The row I/O blocks drive
row, column, or DirectLink interconnects. The column I/O blocks drive column
interconnects.
1
5M40Z, 5M80Z, 5M160Z, and 5M240Z devices have a maximum of five IOEs per row
I/O block.
Figure 2–20 shows how a row I/O block connects to the logic array.
Figure 2–20. Row I/O Block Connection to the Interconnect (Note 1)
R4 Interconnects
C4 Interconnects
I/O Block Local
Interconnect
data_out
[6..0]
7
7
OE
[6..0]
LAB
fast_out
[6..0]
7
7
data_in[6..0]
Direct Link
Interconnect
to Adjacent LAB
LAB Local
Interconnect
Row
I/O Block
Direct Link
Interconnect
from Adjacent LAB
LAB Column
clock [3..0]
Row I/O Block
Contains up to
Seven IOEs
Note to Figure 2–20:
(1) Each of the seven IOEs in the row I/O block can have one data_out or fast_out output, one OE output, and
one data_in input.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
I/O Structure
2–29
Figure 2–21 shows how a column I/O block connects to the logic array.
Figure 2–21. Column I/O Block Connection to the Interconnect (Note 1)
Column I/O
Block Contains
Up To 4 IOEs
Column I/O Block
OE
[3..0]
data_out
[3..0]
4
data_in
[3..0]
fast_out
[3..0]
4
4
4
I/O Block
Local Interconnect
Fast I/O
Interconnect LAB Column
Path Clock [3..0]
R4 Interconnects
LAB
LAB
LAB
LAB Local
Interconnect
LAB Local
Interconnect
LAB Local
Interconnect
C4 Interconnects
C4 Interconnects
Note to Figure 2–21:
(1) Each of the four IOEs in the column I/O block can have one data_out or fast_out output, one OE output, and
one data_in input.
I/O Standards and Banks
Table 2–4 lists the I/O standards supported by MAX V devices.
Table 2–4. MAX V I/O Standards (Part 1 of 2)
Type
Output Supply Voltage (VCCIO)
(V)
3.3-V LVTTL/LVCMOS
Single-ended
3.3
2.5-V LVTTL/LVCMOS
Single-ended
2.5
1.8-V LVTTL/LVCMOS
Single-ended
1.8
1.5-V LVCMOS
Single-ended
1.5
1.2-V LVCMOS
Single-ended
1.2
I/O Standard
December 2010
Altera Corporation
MAX V Device Handbook
2–30
Chapter 2: MAX V Architecture
I/O Structure
Table 2–4. MAX V I/O Standards (Part 2 of 2)
I/O Standard
3.3-V PCI (1)
Type
Output Supply Voltage (VCCIO)
(V)
Single-ended
3.3
LVDS (2)
Differential
2.5
RSDS (3)
Differential
2.5
Notes to Table 2–4:
(1) The 3.3-V PCI compliant I/O is supported in Bank 3 of the 5M1270Z and 5M2210Z devices.
(2) MAX V devices only support emulated LVDS output using a three resistor network (LVDS_E_3R).
(3) MAX V devices only support emulated RSDS output using a three resistor network (RSDS_E_3R).
The 5M40Z, 5M80Z, 5M160Z, 5M240Z, and 5M570Z devices support two I/O banks,
as shown in Figure 2–22. Each of these banks support all the LVTTL, LVCMOS, LVDS,
and RSDS standards shown in Table 2–4. PCI compliant I/O is not supported in these
devices and banks.
Figure 2–22. I/O Banks for 5M40Z, 5M80Z, 5M160Z, 5M240Z, and 5M570Z Devices (Note 1), (2)
I/O Bank 1
I/O Bank 2
All I/O Banks Support
3.3-V LVTTL/LVCMOS,
2.5-V LVTTL/LVCMOS,
1.8-V LVTTL/LVCMOS,
1.5-V LVCMOS,
1.2-V LVCMOS (3),
LVDS (4) ,
RSDS (5)
Notes to Figure 2–22:
(1)
(2)
(3)
(4)
(5)
MAX V Device Handbook
Figure 2–22 is a top view of the silicon die.
Figure 2–22 is a graphical representation only. Refer to the pin list and the Quartus II software for exact pin locations.
This I/O standard is not supported in Bank 1.
Emulated LVDS output using a three resistor network (LVDS_E_3R).
Emulated RSDS output using a three resistor network (RSDS_E_3R).
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
I/O Structure
2–31
The 5M1270Z and 5M2210Z devices support four I/O banks, as shown in Figure 2–23.
Each of these banks support all of the LVTTL, LVCMOS, LVDS, and RSDS standards
shown in Table 2–4. PCI compliant I/O is supported in Bank 3. Bank 3 supports the
PCI clamping diode on inputs and PCI drive compliance on outputs. You must use
Bank 3 for designs requiring PCI compliant I/O pins. The Quartus II software
automatically places I/O pins in this bank if assigned with the PCI I/O standard.
Figure 2–23. I/O Banks for 5M1270Z and 5M2210Z Devices (Note 1), (2)
I/O Bank 2
I/O Bank 1
All I/O Banks Support
3.3-V LVTTL/LVCMOS,
2.5-V LVTTL/LVCMOS,
1.8-V LVTTL/LVCMOS,
1.5-V LVCMOS,
1.2-V LVCMOS (3),
LVDS (4),
RSDS(5)
Also Supports
the 3.3-V PCI
I/O Standard
I/O Bank 3
I/O Bank 4
Notes to Figure 2–23:
(1)
(2)
(3)
(4)
(5)
Figure 2–23 is a top view of the silicon die.
Figure 2–23 is a graphical representation only. Refer to the pin list and the Quartus II software for exact pin locations.
This I/O standard is not supported in Bank 1.
Emulated LVDS output using a three resistor network (LVDS_E_3R).
Emulated RSDS output using a three resistor network (RSDS_E_3R).
Each I/O bank has dedicated VCCIO pins that determine the voltage standard support
in that bank. A single device can support 1.2-V, 1.5-V, 1.8-V, 2.5-V, and 3.3-V interfaces;
each individual bank can support a different standard. Each I/O bank can support
multiple standards with the same V CCIO for input and output pins. For example, when
VCCIO is 3.3 V, Bank 3 can support LVTTL, LVCMOS, and 3.3-V PCI. VCCIO powers
both the input and output buffers in MAX V devices.
The JTAG pins for MAX V devices are dedicated pins that cannot be used as regular
I/O pins. The pins TMS, TDI, TDO, and TCK support all the I/O standards shown in
Table 2–4 on page 2–29 except for PCI and 1.2-V LVCMOS. These pins reside in Bank 1
for all MAX V devices and their I/O standard support is controlled by the V CCIO
setting for Bank 1.
December 2010
Altera Corporation
MAX V Device Handbook
2–32
Chapter 2: MAX V Architecture
I/O Structure
PCI Compliance
The MAX V 5M1270Z and 5M2210Z devices are compliant with PCI applications as
well as all 3.3-V electrical specifications in the PCI Local Bus Specification Revision 2.2.
These devices are also large enough to support PCI intellectual property (IP) cores.
Table 2–5 shows the MAX V device speed grades that meet the PCI timing
specifications.
Table 2–5. 3.3-V PCI Electrical Specifications and PCI Timing Support for MAX V Devices
Device
33-MHz PCI
5M1270Z
All Speed Grades
5M2210Z
All Speed Grades
LVDS and RSDS Channels
The MAX V device supports emulated LVDS and RSDS outputs on both row and
column I/O banks. You can configure the rows and columns as emulated LVDS or
RSDS output buffers that use two single-ended output buffers with three external
resistor networks.
Table 2–6. LVDS and RSDS Channels supported in MAX V Devices (Note 1)
Device
64 MBGA
64 EQFP
68 MBGA
100 TQFP
100 MBGA
144 TQFP
256 FBGA
324 FBGA
5M40Z
10 eTx
20 eTx
—
—
—
—
—
—
5M80Z
10 eTx
20 eTx
20 eTx
33 eTx
—
—
—
—
5M160Z
—
20 eTx
20 eTx
33 eTx
33 eTx
—
—
—
5M240Z
—
—
20 eTx
33 eTx
33 eTx
49 eTx
—
—
5M570Z
—
—
—
28 eTx
28 eTx
49 eTx
75 eTx
—
5M1270Z
—
—
—
—
—
42 eTx
90 eTx
115 eTx
5M2210Z
—
—
—
—
—
—
83 eTx
115 eTx
Note to Table 2–6:
(1) eTx = emulated LVDS output buffers (LVDS_E_3R) or emulated RSDS output buffers (RSDS_E_3R).
Schmitt Trigger
The input buffer for each MAX V device I/O pin has an optional Schmitt trigger
setting for the 3.3-V and 2.5-V standards. The Schmitt trigger allows input buffers to
respond to slow input edge rates with a fast output edge rate. Most importantly,
Schmitt triggers provide hysteresis on the input buffer, preventing slow-rising noisy
input signals from ringing or oscillating on the input signal driven into the logic array.
This provides system noise tolerance on MAX V inputs, but adds a small, nominal
input delay.
The JTAG input pins (TMS, TCK, and TDI) have Schmitt trigger buffers that are always
enabled.
1
MAX V Device Handbook
The TCK input is susceptible to high pulse glitches when the input signal fall time is
greater than 200 ns for all I/O standards.
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
I/O Structure
2–33
Output Enable Signals
Each MAX V IOE output buffer supports output enable signals for tri-state control.
The output enable signal can originate from the GCLK[3..0] global signals or from the
MultiTrack interconnect. The MultiTrack interconnect routes output enable signals
and allows for a unique output enable for each output or bidirectional pin.
MAX V devices also provide a chip-wide output enable pin (DEV_OE) to control the
output enable for every output pin in the design. An option set before compilation in
the Quartus II software controls this pin. This chip-wide output enable uses its own
routing resources and does not use any of the four global resources. If this option is
turned on, all outputs on the chip operate normally when DEV_OE is asserted. When
the pin is deasserted, all outputs are tri-stated. If this option is turned off, the DEV_OE
pin is disabled when the device operates in user mode and is available as a user I/O
pin.
Programmable Drive Strength
The output buffer for each MAX V device I/O pin has two levels of programmable
drive strength control for each of the LVTTL and LVCMOS I/O standards.
Programmable drive strength provides system noise reduction control for high
performance I/O designs. Although a separate slew-rate control feature exists, using
the lower drive strength setting provides signal slew-rate control to reduce system
noise and signal overshoot without the large delay adder associated with the
slew-rate control feature. Table 2–7 lists the possible settings for the I/O standards
with drive strength control. The Quartus II software uses the maximum current
strength as the default setting. The PCI I/O standard is always set at 20 mA with no
alternate setting.
Table 2–7. Programmable Drive Strength (Note 1)
I/O Standard
3.3-V LVTTL
3.3-V LVCMOS
2.5-V LVTTL/LVCMOS
1.8-V LVTTL/LVCMOS
1.5-V LVCMOS
1.2-V LVCMOS
IOH/IOL Current Strength Setting (mA)
16
8
8
4
14
7
6
3
4
2
3
Note to Table 2–7:
(1) The I OH current strength numbers shown are for a condition of a VOUT = VOH minimum, where the VOH
minimum is specified by the I/O standard. The I OL current strength numbers shown are for a condition of a
VOUT = VOL maximum, where the VOL maximum is specified by the I/O standard. For 2.5-V LVTTL/LVCMOS,
the I OH condition is VOUT = 1.7 V and the I OL condition is VOUT = 0.7 V.
1
December 2010
The programmable drive strength feature can be used simultaneously with the
slew-rate control feature.
Altera Corporation
MAX V Device Handbook
2–34
Chapter 2: MAX V Architecture
I/O Structure
Slew-Rate Control
The output buffer for each MAX V device I/O pin has a programmable output
slew-rate control that can be configured for low noise or high-speed performance. A
faster slew rate provides high-speed transitions for high-performance systems.
However, these fast transitions may introduce noise transients into the system. A slow
slew rate reduces system noise, but adds a nominal output delay to rising and falling
edges. The lower the voltage standard (for example, 1.8-V LVTTL) the larger the
output delay when slow slew is enabled. Each I/O pin has an individual slew-rate
control, allowing you to specify the slew rate on a pin-by-pin basis. The slew-rate
control affects both the rising and falling edges. If no slew-rate control is specified, the
Quartus II software defaults to a fast slew rate.
1
The slew-rate control feature can be used simultaneously with the programmable
drive strength feature.
Open-Drain Output
MAX V devices provide an optional open-drain (equivalent to open-collector) output
for each I/O pin. This open-drain output enables the device to provide system-level
control signals (for example, interrupt and write enable signals) that can be asserted
by any of several devices. This output can also provide an additional wired-OR plane.
Programmable Ground Pins
Each unused I/O pin on MAX V devices can be used as an additional ground pin.
This programmable ground feature does not require the use of the associated LEs in
the device. In the Quartus II software, unused pins can be set as programmable GND
on a global default basis or they can be individually assigned. Unused pins also have
the option of being set as tri-stated input pins.
Bus-Hold
Each MAX V device I/O pin provides an optional bus-hold feature. The bus-hold
circuitry can hold the signal on an I/O pin at its last-driven state. Because the bushold feature holds the last-driven state of the pin until the next input signal is present,
an external pull-up or pull-down resistor is not necessary to hold a signal level when
the bus is tri-stated.
The bus-hold circuitry also pulls un-driven pins away from the input threshold
voltage where noise can cause unintended high-frequency switching. You can select
this feature individually for each I/O pin. The bus-hold output will drive no higher
than VCCIO to prevent overdriving signals. If the bus-hold feature is enabled, the
device cannot use the programmable pull-up option.
The bus-hold circuitry is only active after the device has fully initialized. The bus-hold
circuit captures the value on the pin present at the moment user mode is entered.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 2: MAX V Architecture
I/O Structure
2–35
Programmable Pull-Up Resistor
Each MAX V device I/O pin provides an optional programmable pull-up resistor
during user mode. If you enable this feature for an I/O pin, the pull-up resistor holds
the output to the VCCIO level of the output pin’s bank.
1
The programmable pull-up resistor feature should not be used at the same time as the
bus-hold feature on a given I/O pin.
1
The programmable pull-up resistor is active during power-up, ISP, and if the device is
unprogrammed.
Programmable Input Delay
The MAX V IOE includes a programmable input delay that is activated to ensure zero
hold times. A path where a pin directly drives a register, with minimal routing
between the two, may require the delay to ensure zero hold time. However, a path
where a pin drives a register through long routing or through combinational logic
may not require the delay to achieve a zero hold time. The Quartus II software uses
this delay to ensure zero hold times when needed.
MultiVolt I/O Interface
The MAX V architecture supports the MultiVolt I/O interface feature, which allows
MAX V devices in all packages to interface with systems of different supply voltages.
The devices have one set of VCC pins for internal operation (VCCINT ), and up to four
sets for input buffers and I/O output driver buffers (VCCIO ), depending on the
number of I/O banks available in the devices where each set of VCCIO pins powers one
I/O bank. The 5M40Z, 5M80Z, 5M160Z, 5M240Z, and 5M570Z devices each have two
I/O banks while the 5M1270Z and 5M2210Z devices each have four I/O banks.
Connect VCCIO pins to either a 1.2-, 1.5-, 1.8-, 2.5-, or 3.3-V power supply, depending
on the output requirements. The output levels are compatible with systems of the
same voltage as the power supply (that is, when VCCIO pins are connected to a 1.5-V
power supply, the output levels are compatible with 1.5-V systems). When VCCIO pins
are connected to a 3.3-V power supply, the output high is 3.3 V and is compatible with
3.3-V or 5.0-V systems. Table 2–8 summarizes MAX V MultiVolt I/O support.
Table 2–8. MultiVolt I/O Support in MAX V Devices (Part 1 of 2) (Note 1)
Input Signal
Output Signal
VCCIO (V)
1.2 V
1.5 V
1.8 V
2.5 V
3.3 V
5.0 V
1.2 V
1.5 V
1.8 V
2.5 V
3.3 V
5.0 V
1.2
v
—
—
—
—
—
v
—
—
—
—
—
1.5
—
v
v
v
v
—
v
v
—
—
—
—
1.8
—
v
v
v
v
—
v (2) v (2)
v
—
—
—
2.5
—
—
—
v
v
—
v (3) v (3) v (3)
v
—
—
December 2010
Altera Corporation
MAX V Device Handbook
2–36
Chapter 2: MAX V Architecture
Document Revision History
Table 2–8. MultiVolt I/O Support in MAX V Devices (Part 2 of 2) (Note 1)
Input Signal
Output Signal
VCCIO (V)
1.2 V
1.5 V
1.8 V
2.5 V
3.3 V
—
—
—
v (4)
v
3.3
5.0 V
1.2 V
1.5 V
1.8 V
2.5 V
v (5) v (6) v (6) v (6) v (6)
3.3 V
5.0 V
v
v (7)
Notes to Table 2–8:
(1) To drive inputs higher than VCCIO but less than 4.0 V including the overshoot, disable the I/O clamp diode. However, to drive 5.0-V signals to
the device, enable the I/O clamp diode to prevent VI from rising above 4.0 V. Use an external diode if the I/O pin does not support the clamp
diode.
(2) When VCCIO = 1.8 V, a MAX V device can drive a 1.2-V or 1.5-V device with 1.8-V tolerant inputs.
(3) When VCCIO = 2.5 V, a MAX V device can drive a 1.2-V, 1.5-V, or 1.8-V device with 2.5-V tolerant inputs.
(4) When VCCIO = 3.3 V and a 2.5-V input signal feeds an input pin, the VCCIO supply current will be slightly larger than expected.
(5) MAX V devices can be 5.0-V tolerant with the use of an external resistor and the internal I/O clamp diode on the 5M1270Z and 5M2210Z devices.
Use an external clamp diode if the internal clamp diode is not available.
(6) When VCCIO = 3.3 V, a MAX V device can drive a 1.2-V, 1.5-V, 1.8-V, or 2.5-V device with 3.3-V tolerant inputs.
(7) When VCCIO = 3.3 V, a MAX V device can drive a device with 5.0-V TTL inputs but not 5.0-V CMOS inputs. For 5.0-V CMOS, open-drain setting
with internal I/O clamp diode (available only on 5M1270Z and 5M2210Z devices) and external resistor is required. Use an external clamp diode
if the internal clamp diode is not available.
Document Revision History
Table 2–9 lists the revision history for this chapter.
Table 2–9. Document Revision History
Date
December 2010
MAX V Device Handbook
Version
1.0
Changes
Initial release.
December 2010
Altera Corporation
3. DC and Switching Characteristics for
MAX V Devices
May 2011
MV51003-1.2
MV51003-1.2
This chapter covers the electrical and switching characteristics for MAX® V devices.
Electrical characteristics include operating conditions and power consumptions. This
chapter also describes the timing model and specifications.
You must consider the recommended DC and switching conditions described in this
chapter to maintain the highest possible performance and reliability of the MAX V
devices.
This chapter contains the following sections:
■
“Operating Conditions” on page 3–1
■
“Power Consumption” on page 3–10
■
“Timing Model and Specifications” on page 3–10
Operating Conditions
Table 3–1 through Table 3–15 on page 3–9 list information about absolute maximum
ratings, recommended operating conditions, DC electrical characteristics, and other
specifications for MAX V devices.
Absolute Maximum Ratings
Table 3–1 lists the absolute maximum ratings for the MAX V device family.
Table 3–1. Absolute Maximum Ratings for MAX V Devices (Note 1), (2)
Symbol
Parameter
Conditions
With respect to ground
Minimum
Maximum
Unit
–0.5
2.4
V
VCCINT
Internal supply voltage
VCCIO
I/O supply voltage
—
–0.5
4.6
V
VI
DC input voltage
—
–0.5
4.6
V
IOUT
DC output current, per pin
—
–25
25
mA
TSTG
Storage temperature
No bias
–65
150
°C
TAMB
Ambient temperature
Under bias (3)
–65
135
°C
TJ
Junction temperature
TQFP and BGA packages
under bias
—
135
°C
Notes to Table 3–1:
(1) For more information, refer to the Operating Requirements for Altera Devices Data Sheet.
(2) Conditions beyond those listed in Table 3–1 may cause permanent damage to a device. Additionally, device operation at the absolute maximum
ratings for extended periods of time may have adverse affects on the device.
(3) For more information about “under bias” conditions, refer to Table 3–2.
© 2011 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.
and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at
www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but
reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
MAX V Device Handbook
May 2011
Subscribe
3–2
Chapter 3: DC and Switching Characteristics for MAX V Devices
Operating Conditions
Recommended Operating Conditions
Table 3–2 lists recommended operating conditions for the MAX V device family.
Table 3–2. Recommended Operating Conditions for MAX V Devices
Symbol
VCCINT (1)
VCCIO (1)
Parameter
Conditions
Minimum
Maximum
Unit
MAX V devices
1.71
1.89
V
Supply voltage for I/O buffers, 3.3-V
operation
—
3.00
3.60
V
Supply voltage for I/O buffers, 2.5-V
operation
—
2.375
2.625
V
Supply voltage for I/O buffers, 1.8-V
operation
—
1.71
1.89
V
Supply voltage for I/O buffers, 1.5-V
operation
—
1.425
1.575
V
Supply voltage for I/O buffers, 1.2-V
operation
—
1.14
1.26
V
(2), (3), (4)
–0.5
4.0
V
—
0
VCCIO
V
0
85
°C
Industrial range
–40
100
°C
Extended range (5)
–40
125
°C
1.8-V supply voltage for internal logic and
in-system programming (ISP)
VI
Input voltage
VO
Output voltage
Commercial range
TJ
Operating junction temperature
Notes to Table 3–2:
(1) MAX V device ISP and/or user flash memory (UFM) programming using JTAG or logic array is not guaranteed outside the recommended
operating conditions (for example, if brown-out occurs in the system during a potential write/program sequence to the UFM, Altera recommends
that you read back the UFM contents and verify it against the intended write data).
(2) The minimum DC input is –0.5 V. During transitions, the inputs may undershoot to –2.0 V for input currents less than 100 mA and periods
shorter than 20 ns.
(3) During transitions, the inputs may overshoot to the voltages shown below based on the input duty cycle. The DC case is equivalent to 100%
duty cycle. For more information about 5.0-V tolerance, refer to the Using MAX V Devices in Multi-Voltage Systems chapter.
Max. Duty Cycle
VIN
4.0 V 100% (DC)
4.1 V 90%
4.2 V 50%
4.3 V 30%
4.4 V 17%
4.5 V 10%
(4) All pins, including the clock, I/O, and JTAG pins, may be driven before VCCINT and VCCIO are powered.
(5) For the extended temperature range of 100 to 125°C, MAX V UFM programming (erase/write) is only supported using the JTAG interface. UFM
programming using the logic array interface is not guaranteed in this range.
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Operating Conditions
3–3
Programming/Erasure Specifications
Table 3–3 lists the programming/erasure specifications for the MAX V device family.
Table 3–3. Programming/Erasure Specifications for MAX V Devices
Parameter
Block
Erase and reprogram cycles
Minimum
Typical
Maximum
Unit
UFM
—
—
1000 (1)
Cycles
Configuration flash memory (CFM)
—
—
100
Cycles
Note to Table 3–3:
(1) This value applies to the commercial grade devices. For the industrial grade devices, the value is 100 cycles.
DC Electrical Characteristics
Table 3–4 lists DC electrical characteristics for the MAX V device family.
Table 3–4. DC Electrical Characteristics for MAX V Devices (Note 1) (Part 1 of 2)
Symbol
Parameter
Conditions
Minimum
Typical
Maximum
Unit
II
Input pin leakage current VI = VCCIO max to 0 V (2)
–10
—
10
µA
IOZ
Tri-stated I/O pin leakage
current
VO = VCCIO max to 0 V (2)
–10
—
10
µA
5M40Z, 5M80Z, 5M160Z, and
5M240Z (Commercial grade)
(4), (5)
—
25
90
µA
5M240Z (Commercial grade)
(6)
—
27
96
µA
5M40Z, 5M80Z, 5M160Z, and
5M240Z (Industrial grade)
(5), (7)
—
25
139
µA
5M240Z (Industrial grade) (6)
—
27
152
µA
5M570Z (Commercial grade)
(4)
—
27
96
µA
5M570Z (Industrial grade) (7)
—
27
152
µA
ICCSTANDBY
VCCINT supply current
(standby) (3)
VSCHMITT (8)
Hysteresis for Schmitt
trigger input (9)
ICCPOWERUP
VCCINT supply current
during power-up (10)
RPULLUP
May 2011
Value of I/O pin pull-up
resistor during user
mode and ISP
Altera Corporation
5M1270Z and 5M2210Z
—
2
—
mA
VCCIO = 3.3 V
—
400
—
mV
VCCIO = 2.5 V
—
190
—
mV
MAX V devices
—
—
40
mA
VCCIO = 3.3 V (11)
5
—
25
k
VCCIO = 2.5 V (11)
10
—
40
k
VCCIO = 1.8 V (11)
25
—
60
k
VCCIO = 1.5 V (11)
45
—
95
k
VCCIO = 1.2 V (11)
80
—
130
k
MAX V Device Handbook
3–4
Chapter 3: DC and Switching Characteristics for MAX V Devices
Operating Conditions
Table 3–4. DC Electrical Characteristics for MAX V Devices (Note 1) (Part 2 of 2)
Symbol
Parameter
Conditions
Minimum
Typical
Maximum
Unit
IPULLUP
I/O pin pull-up resistor
current when I/O is
unprogrammed
—
—
—
300
µA
CIO
Input capacitance for
user I/O pin
—
—
—
8
pF
CGCLK
Input capacitance for
dual-purpose GCLK/user
I/O pin
—
—
—
8
pF
Notes to Table 3–4:
(1) Typical values are for TA = 25°C, VCCINT = 1.8 V and VCCIO = 1.2, 1.5, 1.8, 2.5, or 3.3 V.
(2) This value is specified for normal device operation. The value may vary during power-up. This applies to all VCCIO settings (3.3, 2.5, 1.8, 1.5,
and 1.2 V).
(3) VI = ground, no load, and no toggling inputs.
(4) Commercial temperature ranges from 0°C to 85°C with the maximum current at 85°C.
(5) Not applicable to the T144 package of the 5M240Z device.
(6) Only applicable to the T144 package of the 5M240Z device.
(7) Industrial temperature ranges from –40°C to 100°C with the maximum current at 100°C.
(8) This value applies to commercial and industrial range devices. For extended temperature range devices, the V SCHMITT typical value is 300 mV
for VCCIO = 3.3 V and 120 mV for VCCIO = 2.5 V.
(9) The TCK input is susceptible to high pulse glitches when the input signal fall time is greater than 200 ns for all I/O standards.
(10) This is a peak current value with a maximum duration of tCONFIG time.
(11) Pin pull-up resistance values will lower if an external source drives the pin higher than VCCIO.
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Operating Conditions
3–5
Output Drive Characteristics
Figure 3–1 shows the typical drive strength characteristics of MAX V devices.
Figure 3–1. Output Drive Characteristics of MAX V Devices (Note 1)
MAX V Output Drive IOH Characteristics
(Maximum Drive Strength)
MAX V Output Drive IOL Characteristics
(Maximum Drive Strength)
60
70
3.3-V VCCIO
3.3-V VCCIO
Typical IO Output Current (mA)
Typical I O Output Current (mA)
60
50
2.5-V VCCIO
40
30
1.8-V VCCIO
20
1.5-V VCCIO
10
50
40
2.5-V VCCIO
30
1.8-V VCCIO
20
1.5-V VCCIO
10
1.2-V VCCIO (2)
1.2-V VCCIO (2)
0
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
0.0
3.5
0.5
1.0
1.5
2.0
2.5
3.0
MAX V Output Drive IOL Characteristics
(Minimum Drive Strength)
MAX V Output Drive IOH Characteristics
(Minimum Drive Strength)
30
35
3.3-V VCCIO
Typical IO Output Current (mA)
Typical IO Output Current (mA)
3.3-V VCCIO
30
25
2.5-V VCCIO
20
15
1.8-V VCCIO
10
1.5-V VCCIO
5
3.5
Voltage (V)
Voltage (V)
0
25
20
2.5-V VCCIO
15
1.8-V VCCIO
10
1.5-V VCCIO
5
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0.0
0.5
1.0
Voltage (V)
1.5
2.0
2.5
3.0
3.5
Voltage (V)
Notes to Figure 3–1:
(1) The DC output current per pin is subject to the absolute maximum rating of Table 3–1 on page 3–1.
(2) 1.2-V VCCIO is only applicable to the maximum drive strength.
I/O Standard Specifications
Table 3–5 through Table 3–13 on page 3–8 list the I/O standard specifications for the
MAX V device family.
Table 3–5. 3.3-V LVTTL Specifications for MAX V Devices
Symbol
Parameter
Conditions
Minimum
Maximum
Unit
VCCIO
I/O supply voltage
—
3.0
3.6
V
VIH
High-level input voltage
—
1.7
4.0
V
VIL
Low-level input voltage
—
–0.5
0.8
V
VOH
High-level output voltage
IOH = –4 mA (1)
2.4
—
V
VOL
Low-level output voltage
IOL = 4 mA (1)
—
0.45
V
Note to Table 3–5:
(1) This specification is supported across all the programmable drive strength settings available for this I/O standard, as shown in the
MAX V Device Architecture chapter.
May 2011
Altera Corporation
MAX V Device Handbook
3–6
Chapter 3: DC and Switching Characteristics for MAX V Devices
Operating Conditions
Table 3–6. 3.3-V LVCMOS Specifications for MAX V Devices
Symbol
Parameter
Conditions
Minimum
Maximum
Unit
VCCIO
I/O supply voltage
—
3.0
3.6
V
VIH
High-level input voltage
—
1.7
4.0
V
VIL
Low-level input voltage
—
–0.5
0.8
V
VCCIO – 0.2
—
V
—
0.2
V
VOH
High-level output voltage
VCCIO = 3.0,
IOH = –0.1 mA (1)
VOL
Low-level output voltage
VCCIO = 3.0,
IOL = 0.1 mA (1)
Note to Table 3–6:
(1) This specification is supported across all the programmable drive strength settings available for this I/O standard, as shown in the
MAX V Device Architecture chapter.
Table 3–7. 2.5-V I/O Specifications for MAX V Devices
Symbol
Parameter
Conditions
Minimum
Maximum
Unit
VCCIO
I/O supply voltage
—
2.375
2.625
V
VIH
High-level input voltage
—
1.7
4.0
V
VIL
Low-level input voltage
—
–0.5
0.7
V
IOH = –0.1 mA (1)
2.1
—
V
IOH = –1 mA (1)
2.0
—
V
IOH = –2 mA (1)
1.7
—
V
IOL = 0.1 mA (1)
—
0.2
V
IOL = 1 mA (1)
—
0.4
V
IOL = 2 mA (1)
—
0.7
V
High-level output voltage
VOH
VOL
Low-level output voltage
Note to Table 3–7:
(1) This specification is supported across all the programmable drive strength settings available for this I/O standard, as shown in the
MAX V Device Architecture chapter.
Table 3–8. 1.8-V I/O Specifications for MAX V Devices
Symbol
Parameter
Conditions
Minimum
Maximum
Unit
VCCIO
I/O supply voltage
—
1.71
1.89
V
VIH
High-level input voltage
—
0.65 × VCCIO
2.25 (2)
V
VIL
Low-level input voltage
—
–0.3
0.35 × VCCIO
V
VOH
High-level output voltage
IOH = –2 mA (1)
VCCIO – 0.45
—
V
VOL
Low-level output voltage
IOL = 2 mA (1)
—
0.45
V
Notes to Table 3–8:
(1) This specification is supported across all the programmable drive strength settings available for this I/O standard, as shown in the
MAX V Device Architecture chapter.
(2) This maximum VIH reflects the JEDEC specification. The MAX V input buffer can tolerate a VIH maximum of 4.0, as specified by the VI parameter
in Table 3–2 on page 3–2.
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Operating Conditions
3–7
Table 3–9. 1.5-V I/O Specifications for MAX V Devices
Symbol
Parameter
Conditions
Minimum
Maximum
Unit
VCCIO
I/O supply voltage
—
1.425
1.575
V
VIH
High-level input voltage
—
0.65 × VCCIO
VCCIO + 0.3 (2)
V
VIL
Low-level input voltage
—
–0.3
0.35 × VCCIO
V
VOH
High-level output voltage
IOH = –2 mA (1)
0.75 × VCCIO
—
V
VOL
Low-level output voltage
IOL = 2 mA (1)
—
0.25 × VCCIO
V
Notes to Table 3–9:
(1) This specification is supported across all the programmable drive strength settings available for this I/O standard, as shown in the
MAX V Device Architecture chapter.
(2) This maximum VIH reflects the JEDEC specification. The MAX V input buffer can tolerate a VIH maximum of 4.0, as specified by the VI parameter
in Table 3–2 on page 3–2.
Table 3–10. 1.2-V I/O Specifications for MAX V Devices
Symbol
Parameter
Conditions
Minimum
Maximum
Unit
VCCIO
I/O supply voltage
—
1.14
1.26
V
VIH
High-level input voltage
—
0.8 × VCCIO
VCCIO + 0.3
V
VIL
Low-level input voltage
—
–0.3
0.25 × VCCIO
V
VOH
High-level output voltage
IOH = –2 mA (1)
0.75 × VCCIO
—
V
VOL
Low-level output voltage
IOL = 2 mA (1)
—
0.25 × VCCIO
V
Note to Table 3–10:
(1) This specification is supported across all the programmable drive strength settings available for this I/O standard, as shown in the
MAX V Device Architecture chapter.
Table 3–11. 3.3-V PCI Specifications for MAX V Devices (Note 1)
Symbol
Parameter
Conditions
Minimum
Typical
Maximum
Unit
VCCIO
I/O supply voltage
—
3.0
3.3
3.6
V
VIH
High-level input voltage
—
0.5 × VCCIO
—
VCCIO + 0.5
V
VIL
Low-level input voltage
—
–0.5
—
0.3 × VCCIO
V
VOH
High-level output voltage
IOH = –500 µA
0.9 × VCCIO
—
—
V
VOL
Low-level output voltage
IOL = 1.5 mA
—
—
0.1 × VCCIO
V
Note to Table 3–11:
(1) 3.3-V PCI I/O standard is only supported in Bank 3 of the 5M1270Z and 5M2210Z devices.
Table 3–12. LVDS Specifications for MAX V Devices (Note 1)
Symbol
Parameter
Conditions
Minimum
Typical
Maximum
Unit
VCCIO
I/O supply voltage
—
2.375
2.5
2.625
V
VOD
Differential output voltage swing
—
247
—
600
mV
VOS
Output offset voltage
—
1.125
1.25
1.375
V
Note to Table 3–12:
(1) Supports emulated LVDS output using a three-resistor network (LVDS_E_3R).
May 2011
Altera Corporation
MAX V Device Handbook
3–8
Chapter 3: DC and Switching Characteristics for MAX V Devices
Operating Conditions
Table 3–13. RSDS Specifications for MAX V Devices (Note 1)
Symbol
Parameter
Conditions
Minimum
Typical
Maximum
Unit
VCCIO
I/O supply voltage
—
2.375
2.5
2.625
V
VOD
Differential output voltage swing
—
247
—
600
mV
VOS
Output offset voltage
—
1.125
1.25
1.375
V
Note to Table 3–13:
(1) Supports emulated RSDS output using a three-resistor network (RSDS_E_3R).
Bus Hold Specifications
Table 3–14 lists the bus hold specifications for the MAX V device family.
Table 3–14. Bus Hold Specifications for MAX V Devices
VCCIO Level
Parameter
Conditions
1.2 V
1.5 V
1.8 V
2.5 V
3.3 V
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Unit
Low sustaining
current
VIN > VIL (maximum)
10
—
20
—
30
—
50
—
70
—
µA
High sustaining
current
VIN < VIH (minimum)
–10
—
–20
—
–30
—
–50
—
–70
—
µA
Low overdrive
current
0 V < VIN < VCCIO
—
130
—
160
—
200
—
300
—
500
µA
High overdrive
current
0 V < VIN < VCCIO
—
–130
—
–160
—
–200
—
–300
—
–500
µA
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Operating Conditions
3–9
Power-Up Timing
Table 3–15 lists the power-up timing characteristics for the MAX V device family.
Table 3–15. Power-Up Timing for MAX V Devices
Symbol
Parameter
Device
5M40Z
5M80Z
5M160Z
5M240Z (2)
tCONFIG
The amount of time from
when minimum VCCINT is
reached until the device
enters user mode (1)
5M240Z (3)
5M570Z
5M1270Z (4)
5M1270Z (5)
5M2210Z
Temperature Range
Min
Typ
Max
Unit
Commercial and industrial
—
—
200
µs
Extended
—
—
300
µs
Commercial and industrial
—
—
200
µs
Extended
—
—
300
µs
Commercial and industrial
—
—
200
µs
Extended
—
—
300
µs
Commercial and industrial
—
—
200
µs
Extended
—
—
300
µs
Commercial and industrial
—
—
300
µs
Extended
—
—
400
µs
Commercial and industrial
—
—
300
µs
Extended
—
—
400
µs
Commercial and industrial
—
—
300
µs
Extended
—
—
400
µs
Commercial and industrial
—
—
450
µs
Extended
—
—
500
µs
Commercial and industrial
—
—
450
µs
Extended
—
—
500
µs
Notes to Table 3–15:
(1) For more information about power-on reset (POR) trigger voltage, refer to the Hot Socketing and Power-On Reset in MAX V Devices chapter.
(2) Not applicable to the T144 package of the 5M240Z device.
(3) Only applicable to the T144 package of the 5M240Z device.
(4) Not applicable to the F324 package of the 5M1270Z device.
(5) Only applicable to the F324 package of the 5M1270Z device.
May 2011
Altera Corporation
MAX V Device Handbook
3–10
Chapter 3: DC and Switching Characteristics for MAX V Devices
Power Consumption
Power Consumption
You can use the Altera® PowerPlay Early Power Estimator and PowerPlay Power
Analyzer to estimate the device power.
f For more information about these power analysis tools, refer to the PowerPlay Early
Power Estimator for Altera CPLDs User Guide and the PowerPlay Power Analysis chapter
in volume 3 of the Quartus II Handbook.
Timing Model and Specifications
MAX V devices timing can be analyzed with the Altera Quartus® II software, a variety
of industry-standard EDA simulators and timing analyzers, or with the timing model
shown in Figure 3–2.
MAX V devices have predictable internal delays that allow you to determine the
worst-case timing of any design. The software provides timing simulation,
point-to-point delay prediction, and detailed timing analysis for device-wide
performance evaluation.
Figure 3–2. Timing Model for MAX V Devices
Output and Output Enable
Data Delay
t R4
tIODR
tIOE
Data-In/LUT Chain
User
Flash
Memory
I/O Pin
INPUT
Input Routing
Delay
tDL
t LOCAL
I/O Input Delay
t IN
Logic Element
LUT Delay
t LUT
Register Control
Delay
tC
tCOMB
t FASTIO
tCO
tSU
tH
tPRE
tCLR
Output
Delay
t OD
t XZ
t ZX
I/O Pin
From Adjacent LE
t GLOB
Global Input Delay
Output Routing
Delay
t C4
Combinational Path Delay
To Adjacent LE
Register Delays
Data-Out
You can derive the timing characteristics of any signal path from the timing model
and parameters of a particular device. You can calculate external timing parameters,
which represent pin-to-pin timing delays, as the sum of the internal parameters.
f For more information, refer to AN629: Understanding Timing in Altera CPLDs.
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
3–11
Preliminary and Final Timing
This section describes the performance, internal, external, and UFM timing
specifications. All specifications are representative of the worst-case supply voltage
and junction temperature conditions.
Timing models can have either preliminary or final status. The Quartus II software
issues an informational message during the design compilation if the timing models
are preliminary. Table 3–16 lists the status of the MAX V device timing models.
Preliminary status means the timing model is subject to change. Initially, timing
numbers are created using simulation results, process data, and other known
parameters. These tests are used to make the preliminary numbers as close to the
actual timing parameters as possible.
Final timing numbers are based on actual device operation and testing. These
numbers reflect the actual performance of the device under the worst-case voltage
and junction temperature conditions.
Table 3–16. Timing Model Status for MAX V Devices
Device
Final
5M40Z
v
5M80Z
v
5M160Z
v
5M240Z
v
5M570Z
v
5M1270Z
v
5M2210Z
v
Performance
Table 3–17 lists the MAX V device performance for some common designs. All
performance values were obtained with the Quartus II software compilation of
megafunctions.
Table 3–17. Device Performance for MAX V Devices (Part 1 of 2)
Performance
Resources Used
Resource
Used
LE
May 2011
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
Design Size and
Function
5M1270Z/ 5M2210Z
Unit
Mode
LEs
UFM
Blocks
C4
C5, I5
C4
C5, I5
16-bit counter (1)
—
16
0
184.1
118.3
247.5
201.1
MHz
64-bit counter (1)
—
64
0
83.2
80.5
154.8
125.8
MHz
16-to-1 multiplexer
—
11
0
17.4
20.4
8.0
9.3
ns
32-to-1 multiplexer
—
24
0
12.5
25.3
9.0
11.4
ns
16-bit XOR function
—
5
0
9.0
16.1
6.6
8.2
ns
16-bit decoder with
single address line
—
5
0
9.2
16.1
6.6
8.2
ns
Altera Corporation
MAX V Device Handbook
3–12
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
Table 3–17. Device Performance for MAX V Devices (Part 2 of 2)
Performance
Resources Used
Resource
Used
UFM
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
Design Size and
Function
5M1270Z/ 5M2210Z
Unit
Mode
LEs
UFM
Blocks
C4
C5, I5
C4
C5, I5
512 × 16
None
3
1
10.0
10.0
10.0
10.0
MHz
512 × 16
SPI (2)
37
1
9.7
9.7
8.0
8.0
MHz
512 × 8
Parallel
(3)
73
1
(4)
(4)
(4)
(4)
MHz
512 × 16
I2C (3)
142
1
100 (5)
100 (5)
100 (5)
100 (5)
kHz
Notes to Table 3–17:
(1) This design is a binary loadable up counter.
(2) This design is configured for read-only operation in Extended mode. Read and write ability increases the number of logic elements (LEs) used.
(3) This design is configured for read-only operation. Read and write ability increases the number of LEs used.
(4) This design is asynchronous.
(5) The I2C megafunction is verified in hardware up to 100-kHz serial clock line rate.
Internal Timing Parameters
Internal timing parameters are specified on a speed grade basis independent of device
density. Table 3–18 through Table 3–25 on page 3–19 list the MAX V device internal
timing microparameters for LEs, input/output elements (IOEs), UFM blocks, and
MultiTrack interconnects.
f For more information about each internal timing microparameters symbol, refer to
AN629: Understanding Timing in Altera CPLDs.
Table 3–18. LE Internal Timing Microparameters for MAX V Devices (Part 1 of 2)
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
Symbol
Parameter
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
tLUT
LE combinational look-up
table (LUT) delay
—
1,215
—
2,247
—
742
—
914
ps
tCOMB
Combinational path delay
—
243
—
309
—
192
—
236
ps
tCLR
LE register clear delay
401
—
545
—
309
—
381
—
ps
tPRE
LE register preset delay
401
—
545
—
309
—
381
—
ps
tSU
LE register setup time
before clock
260
—
321
—
271
—
333
—
ps
tH
LE register hold time
after clock
0
—
0
—
0
—
0
—
ps
tCO
LE register
clock-to-output delay
—
380
—
494
—
305
—
376
ps
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
3–13
Table 3–18. LE Internal Timing Microparameters for MAX V Devices (Part 2 of 2)
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
Symbol
Parameter
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
tCLKHL
Minimum clock high or
low time
253
—
339
—
216
—
266
—
ps
tC
Register control delay
—
1,356
—
1,741
—
1,114
—
1,372
ps
Table 3–19. IOE Internal Timing Microparameters for MAX V Devices
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
Symbol
Parameter
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
tFASTIO
Data output delay from
adjacent LE to I/O block
—
170
—
428
—
207
—
254
ps
tIN
I/O input pad and buffer
delay
—
907
—
986
—
920
—
1,132
ps
tGLOB (1)
I/O input pad and buffer
delay used as global
signal pin
—
2,261
—
3,322
—
1,974
—
2,430
ps
tIOE
Internally generated
output enable delay
—
530
—
1,410
—
374
—
460
ps
tDL
Input routing delay
—
318
—
509
—
291
—
358
ps
tOD (2)
Output delay buffer and
pad delay
—
1,319
—
1,543
—
1,383
—
1,702
ps
tXZ (3)
Output buffer disable
delay
—
1,045
—
1,276
—
982
—
1,209
ps
tZX (4)
Output buffer enable
delay
—
1,160
—
1,353
—
1,303
—
1,604
ps
Notes to Table 3–19:
(1) Delay numbers for tGLOB differ for each device density and speed grade. The delay numbers for tGLOB, shown in Table 3–19, are based on a 5M240Z
device target.
(2) For more information about delay adders associated with different I/O standards, drive strengths, and slew rates, refer to Table 3–34 on page 3–24
and Table 3–35 on page 3–25.
(3) For more information about tXZ delay adders associated with different I/O standards, drive strengths, and slew rates, refer to Table 3–22 on
page 3–15 and Table 3–23 on page 3–15.
(4) For more information about tZX delay adders associated with different I/O standards, drive strengths, and slew rates, refer to Table 3–20 on
page 3–14 and Table 3–21 on page 3–14.
May 2011
Altera Corporation
MAX V Device Handbook
3–14
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
Table 3–20 through Table 3–23 list the adder delays for tZX and tXZ microparameters
when using an I/O standard other than 3.3-V LVTTL with 16 mA drive strength.
Table 3–20. tZX IOE Microparameter Adders for Fast Slew Rate for MAX V Devices
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
Standard
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
16 mA
—
0
—
0
—
0
—
0
ps
8 mA
—
72
—
74
—
101
—
125
ps
8 mA
—
0
—
0
—
0
—
0
ps
4 mA
—
72
—
74
—
101
—
125
ps
2.5-V LVTTL /
LVCMOS
14 mA
—
126
—
127
—
155
—
191
ps
7 mA
—
196
—
197
—
545
—
671
ps
1.8-V LVTTL /
LVCMOS
6 mA
—
608
—
610
—
721
—
888
ps
3 mA
—
681
—
685
—
2012
—
2477
ps
4 mA
—
1162
—
1157
—
1590
—
1957
ps
2 mA
—
1245
—
1244
—
3269
—
4024
ps
1.2-V LVCMOS
3 mA
—
1889
—
1856
—
2860
—
3520
ps
3.3-V PCI
20 mA
—
72
—
74
—
–18
—
–22
ps
LVDS
—
—
126
—
127
—
155
—
191
ps
RSDS
—
—
126
—
127
—
155
—
191
ps
3.3-V LVTTL
3.3-V LVCMOS
1.5-V LVCMOS
Table 3–21. tZX IOE Microparameter Adders for Slow Slew Rate for MAX V Devices
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
Standard
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
16 mA
—
5,951
—
6,063
—
6,012
—
5,743
ps
8 mA
—
6,534
—
6,662
—
8,785
—
8,516
ps
8 mA
—
5,951
—
6,063
—
6,012
—
5,743
ps
4 mA
—
6,534
—
6,662
—
8,785
—
8,516
ps
2.5-V LVTTL /
LVCMOS
14 mA
—
9,110
—
9,237
—
10,072
—
9,803
ps
7 mA
—
9,830
—
9,977
—
12,945
—
12,676
ps
1.8-V LVTTL /
LVCMOS
6 mA
—
21,800
—
21,787
—
21,185
—
20,916
ps
3 mA
—
23,020
—
23,037
—
24,597
—
24,328
ps
4 mA
—
39,120
—
39,067
—
34,517
—
34,248
ps
2 mA
—
40,670
—
40,617
—
39,717
—
39,448
ps
1.2-V LVCMOS
3 mA
—
69,505
—
70,461
—
55,800
—
55,531
ps
3.3-V PCI
20 mA
—
6,534
—
6,662
—
35
—
44
ps
3.3-V LVTTL
3.3-V LVCMOS
1.5-V LVCMOS
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
3–15
Table 3–22. tXZ IOE Microparameter Adders for Fast Slew Rate for MAX V Devices
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
Standard
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
—
0
—
0
—
0
—
0
ps
8 mA
—
–69
—
–69
—
–74
—
–91
ps
8 mA
—
0
—
0
—
0
—
0
ps
4 mA
—
–69
—
–69
—
–74
—
–91
ps
2.5-V LVTTL /
LVCMOS
14 mA
—
–7
—
–10
—
–46
—
–56
ps
7 mA
—
–66
—
–69
—
–82
—
–101
ps
1.8-V LVTTL /
LVCMOS
6 mA
—
45
—
37
—
–7
—
–8
ps
3 mA
—
34
—
25
—
119
—
147
ps
4 mA
—
166
—
155
—
339
—
418
ps
3.3-V LVTTL
3.3-V LVCMOS
1.5-V LVCMOS
16 mA
2 mA
—
190
—
179
—
464
—
571
ps
1.2-V LVCMOS
3 mA
—
300
—
283
—
817
—
1,006
ps
3.3-V PCI
20 mA
—
–69
—
–69
—
80
—
99
ps
LVDS
—
—
–7
—
–10
—
–46
—
–56
ps
RSDS
—
—
–7
—
–10
—
–46
—
–56
ps
Table 3–23. tXZ IOE Microparameter Adders for Slow Slew Rate for MAX V Devices
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
Standard
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Min
Max
Min
Max
Min
16 mA
—
171
—
174
—
8 mA
—
112
—
116
—
8 mA
—
171
—
174
—
4 mA
—
112
—
116
2.5-V LVTTL /
LVCMOS
14 mA
—
213
—
7 mA
—
166
1.8-V LVTTL /
LVCMOS
6 mA
—
3 mA
Unit
C5, I5
Min
Max
73
—
–132
ps
758
—
553
ps
73
—
–132
ps
—
758
—
553
ps
213
—
32
—
–173
ps
—
166
—
714
—
509
ps
441
—
438
—
96
—
–109
ps
—
496
—
494
—
963
—
758
ps
4 mA
—
765
—
755
—
238
—
33
ps
2 mA
—
903
—
897
—
1,319
—
1,114
ps
1.2-V LVCMOS
3 mA
—
1,159
—
1,130
—
400
—
195
ps
3.3-V PCI
20 mA
—
112
—
116
—
303
—
373
ps
3.3-V LVTTL
3.3-V LVCMOS
1.5-V LVCMOS
May 2011
Altera Corporation
Max
MAX V Device Handbook
3–16
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
1
The default slew rate setting for MAX V devices in the Quartus II design software is
“fast”.
Table 3–24. UFM Block Internal Timing Microparameters for MAX V Devices (Part 1 of 2)
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
Symbol
Parameter
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
tACLK
Address register clock
period
100
—
100
—
100
—
100
—
ns
tASU
Address register shift
signal setup to address
register clock
20
—
20
—
20
—
20
—
ns
tAH
Address register shift
signal hold to address
register clock
20
—
20
—
20
—
20
—
ns
tADS
Address register data in
setup to address register
clock
20
—
20
—
20
—
20
—
ns
tADH
Address register data in
hold from address
register clock
20
—
20
—
20
—
20
—
ns
tDCLK
Data register clock period
100
—
100
—
100
—
100
—
ns
tDSS
Data register shift signal
setup to data register
clock
60
—
60
—
60
—
60
—
ns
tDSH
Data register shift signal
hold from data register
clock
20
—
20
—
20
—
20
—
ns
tDDS
Data register data in
setup to data register
clock
20
—
20
—
20
—
20
—
ns
tDDH
Data register data in hold
from data register clock
20
—
20
—
20
—
20
—
ns
tDP
Program signal to data
clock hold time
0
—
0
—
0
—
0
—
ns
tPB
Maximum delay between
program rising edge to
UFM busy signal rising
edge
—
960
—
960
—
960
—
960
ns
tBP
Minimum delay allowed
from UFM busy signal
going low to program
signal going low
20
—
20
—
20
—
20
—
ns
tPPMX
Maximum length of busy
pulse during a program
—
100
—
100
—
100
—
100
µs
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
3–17
Table 3–24. UFM Block Internal Timing Microparameters for MAX V Devices (Part 2 of 2)
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
Symbol
Parameter
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
tAE
Minimum erase signal
to address clock hold
time
0
—
0
—
0
—
0
—
ns
tEB
Maximum delay between
the erase rising edge to
the UFM busy signal
rising edge
—
960
—
960
—
960
—
960
ns
tBE
Minimum delay allowed
from the UFM busy
signal going low to
erase signal going low
20
—
20
—
20
—
20
—
ns
tEPMX
Maximum length of busy
pulse during an erase
—
500
—
500
—
500
—
500
ms
tDCO
Delay from data register
clock to data register
output
—
5
—
5
—
5
—
5
ns
tOE
Delay from OSC_ENA
signal reaching UFM to
rising clock of OSC
leaving the UFM
180
—
180
—
180
—
180
—
ns
tRA
Maximum read access
time
—
65
—
65
—
65
—
65
ns
tOSCS
Maximum delay between
the OSC_ENA rising edge
to the erase/program
signal rising edge
250
—
250
—
250
—
250
—
ns
tOSCH
Minimum delay allowed
from the
erase/program signal
going low to OSC_ENA
signal going low
250
—
250
—
250
—
250
—
ns
May 2011
Altera Corporation
MAX V Device Handbook
3–18
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
Figure 3–3 through Figure 3–5 show the read, program, and erase waveforms for
UFM block timing parameters listed in Table 3–24.
Figure 3–3. UFM Read Waveform
ARShft
tASU
tACLK
9 Address Bits tAH
ARClk
tADH
ARDin
DRShft
tADS
tDSS
DRClk
tDCLK 16 Data Bits
tDSH
tDCO
DRDin
DRDout
OSC_ENA
Program
Erase
Busy
Figure 3–4. UFM Program Waveform
ARShft
tASU
ARClk
9 Address Bits
tACLK
tAH
tADH
ARDin
DRShft
tADS
tDSS
16 Data Bits
tDCLK
tDSH
DRClk
DRDin
DRDout
tDDS
tDDH
tOSCS
tOSCH
OSC_ENA
Program
Erase
tPB
tBP
Busy
tPPMX
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
3–19
Figure 3–5. UFM Erase Waveform
ARShft
tASU
tACLK
9 Address Bits
ARClk
tAH
tADH
ARDin
tADS
DRShft
DRClk
DRDin
DRDout
OSC_ENA
tOSCS
Program
tOSCH
Erase
tEB
Busy
tBE
tEPMX
Table 3–25. Routing Delay Internal Timing Microparameters for MAX V Devices
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
Routing
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
tC4
—
860
—
1,973
—
561
—
690
tR4
—
655
—
1,479
—
445
—
548
ps
tLOCAL
—
1,143
—
2,947
—
731
—
899
ps
ps
External Timing Parameters
External timing parameters are specified by device density and speed grade. All
external I/O timing parameters shown are for the 3.3-V LVTTL I/O standard with the
maximum drive strength and fast slew rate. For external I/O timing using standards
other than LVTTL or for different drive strengths, use the I/O standard input and
output delay adders in Table 3–32 on page 3–23 through Table 3–36 on page 3–25.
f For more information about each external timing parameters symbol, refer to
AN629: Understanding Timing in Altera CPLDs.
May 2011
Altera Corporation
MAX V Device Handbook
3–20
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
Table 3–26 lists the external I/O timing parameters for the 5M40Z, 5M80Z, 5M160Z,
and 5M240Z devices.
Table 3–26. Global Clock External I/O Timing Parameters for the 5M40Z, 5M80Z, 5M160Z, and 5M240Z Devices
(Note 1), (2)
C4
Symbol
Parameter
C5, I5
Condition
Unit
Min
Max
Min
Max
tPD1
Worst case pin-to-pin delay through one LUT
10 pF
—
7.9
—
14.0
ns
tPD2
Best case pin-to-pin delay through one LUT
10 pF
—
5.8
—
8.5
ns
tSU
Global clock setup time
—
2.4
—
4.6
—
ns
tH
Global clock hold time
—
0
—
0
—
ns
tCO
Global clock to output delay
10 pF
2.0
6.6
2.0
8.6
ns
tCH
Global clock high time
—
253
—
339
—
ps
tCL
Global clock low time
—
253
—
339
—
ps
tCNT
Minimum global clock period for
16-bit counter
—
5.4
—
8.4
—
ns
fCNT
Maximum global clock frequency for 16-bit
counter
—
—
184.1
—
118.3
MHz
Notes to Table 3–26:
(1) The maximum frequency is limited by the I/O standard on the clock input pin. The 16-bit counter critical delay performs faster than this global
clock input pin maximum frequency.
(2) Not applicable to the T144 package of the 5M240Z device.
Table 3–27 lists the external I/O timing parameters for the T144 package of the
5M240Z device.
Table 3–27. Global Clock External I/O Timing Parameters for the 5M240Z Device (Note 1), (2)
C4
Symbol
Parameter
C5, I5
Condition
Unit
Min
Max
Min
Max
tPD1
Worst case pin-to-pin delay through one LUT
10 pF
—
9.5
—
17.7
ns
tPD2
Best case pin-to-pin delay through one LUT
10 pF
—
5.7
—
8.5
ns
tSU
Global clock setup time
—
2.2
—
4.4
—
ns
tH
Global clock hold time
—
0
—
0
—
ns
tCO
Global clock to output delay
10 pF
2.0
6.7
2.0
8.7
ns
tCH
Global clock high time
—
253
—
339
—
ps
tCL
Global clock low time
—
253
—
339
—
ps
tCNT
Minimum global clock period for 16-bit
counter
—
5.4
—
8.4
—
ns
fCNT
Maximum global clock frequency for 16-bit
counter
—
—
184.1
—
118.3
MHz
Notes to Table 3–27:
(1) The maximum frequency is limited by the I/O standard on the clock input pin. The 16-bit counter critical delay performs faster than this global
clock input pin maximum frequency.
(2) Only applicable to the T144 package of the 5M240Z device.
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
3–21
Table 3–28 lists the external I/O timing parameters for the 5M570Z device.
Table 3–28. Global Clock External I/O Timing Parameters for the 5M570Z Device (Note 1)
C4
Symbol
Parameter
C5, I5
Condition
Unit
Min
Max
Min
Max
tPD1
Worst case pin-to-pin delay through one LUT
10 pF
—
9.5
—
17.7
ns
tPD2
Best case pin-to-pin delay through one LUT
10 pF
—
5.7
—
8.5
ns
tSU
Global clock setup time
—
2.2
—
4.4
—
ns
tH
Global clock hold time
—
0
—
0
—
ns
tCO
Global clock to output delay
10 pF
2.0
6.7
2.0
8.7
ns
tCH
Global clock high time
—
253
—
339
—
ps
tCL
Global clock low time
—
253
—
339
—
ps
tCNT
Minimum global clock period for 16-bit
counter
—
5.4
—
8.4
—
ns
fCNT
Maximum global clock frequency for 16-bit
counter
—
—
184.1
—
118.3
MHz
Note to Table 3–28:
(1) The maximum frequency is limited by the I/O standard on the clock input pin. The 16-bit counter critical delay performs faster than this global
clock input pin maximum frequency.
Table 3–29 lists the external I/O timing parameters for the 5M1270Z device.
Table 3–29. Global Clock External I/O Timing Parameters for the 5M1270Z Device (Note 1), (2)
C4
Symbol
Parameter
C5, I5
Condition
Unit
Min
Max
Min
Max
tPD1
Worst case pin-to-pin delay through one LUT
10 pF
—
8.1
—
10.0
ns
tPD2
Best case pin-to-pin delay through one LUT
10 pF
—
4.8
—
5.9
ns
tSU
Global clock setup time
—
1.5
—
1.9
—
ns
tH
Global clock hold time
—
0
—
0
—
ns
tCO
Global clock to output delay
10 pF
2.0
5.9
2.0
7.3
ns
tCH
Global clock high time
—
216
—
266
—
ps
tCL
Global clock low time
—
216
—
266
—
ps
tCNT
Minimum global clock period for 16-bit
counter
—
4.0
—
5.0
—
ns
fCNT
Maximum global clock frequency for 16-bit
counter
—
—
247.5
—
201.1
MHz
Notes to Table 3–29:
(1) The maximum frequency is limited by the I/O standard on the clock input pin. The 16-bit counter critical delay performs faster than this global
clock input pin maximum frequency.
(2) Not applicable to the F324 package of the 5M1270Z device.
May 2011
Altera Corporation
MAX V Device Handbook
3–22
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
Table 3–30 lists the external I/O timing parameters for the F324 package of the
5M1270Z device.
Table 3–30. Global Clock External I/O Timing Parameters for the 5M1270Z Device (Note 1), (2)
C4
Symbol
Parameter
C5, I5
Condition
Unit
Min
Max
Min
Max
tPD1
Worst case pin-to-pin delay through one LUT
10 pF
—
9.1
—
11.2
ns
tPD2
Best case pin-to-pin delay through one LUT
10 pF
—
4.8
—
5.9
ns
tSU
Global clock setup time
—
1.5
—
1.9
—
ns
tH
Global clock hold time
tCO
Global clock to output delay
tCH
—
0
—
0
—
ns
10 pF
2.0
6.0
2.0
7.4
ns
Global clock high time
—
216
—
266
—
ps
tCL
Global clock low time
—
216
—
266
—
ps
tCNT
Minimum global clock period for 16-bit
counter
—
4.0
—
5.0
—
ns
fCNT
Maximum global clock frequency for 16-bit
counter
—
—
247.5
—
201.1
MHz
Notes to Table 3–30:
(1) The maximum frequency is limited by the I/O standard on the clock input pin. The 16-bit counter critical delay performs faster than this global
clock input pin maximum frequency.
(2) Only applicable to the F324 package of the 5M1270Z device.
Table 3–31 lists the external I/O timing parameters for the 5M2210Z device.
Table 3–31. Global Clock External I/O Timing Parameters for the 5M2210Z Device (Note 1)
C4
Symbol
Parameter
C5, I5
Condition
Unit
Min
Max
Min
Max
—
9.1
—
11.2
tPD1
Worst case pin-to-pin delay through one LUT
10 pF
tPD2
Best case pin-to-pin delay through one LUT
10 pF
—
4.8
—
5.9
ns
tSU
Global clock setup time
—
1.5
—
1.9
—
ns
tH
Global clock hold time
—
0
—
0
—
ns
tCO
Global clock to output delay
10 pF
2.0
6.0
2.0
7.4
ns
tCH
Global clock high time
—
216
—
266
—
ps
tCL
Global clock low time
—
216
—
266
—
ps
tCNT
Minimum global clock period for 16-bit
counter
—
4.0
—
5.0
—
ns
fCNT
Maximum global clock frequency for 16-bit
counter
—
—
247.5
—
201.1
MHz
ns
Note to Table 3–31:
(1) The maximum frequency is limited by the I/O standard on the clock input pin. The 16-bit counter critical delay performs faster than this global
clock input pin maximum frequency.
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
3–23
External Timing I/O Delay Adders
The I/O delay timing parameters for the I/O standard input and output adders and
the input delays are specified by speed grade, independent of device density.
Table 3–32 through Table 3–36 on page 3–25 list the adder delays associated with I/O
pins for all packages. If you select an I/O standard other than 3.3-V LVTTL, add the
input delay adder to the external tSU timing parameters listed in Table 3–26 on
page 3–20 through Table 3–31. If you select an I/O standard other than 3.3-V LVTTL
with 16 mA drive strength and fast slew rate, add the output delay adder to the
external tCO and tPD listed in Table 3–26 on page 3–20 through Table 3–31.
Table 3–32. External Timing Input Delay Adders for MAX V Devices
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
I/O Standard
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
Without Schmitt
Trigger
—
0
—
0
—
0
—
0
ps
With Schmitt
Trigger
—
387
—
442
—
480
—
591
ps
Without Schmitt
Trigger
—
0
—
0
—
0
—
0
ps
With Schmitt
Trigger
—
387
—
442
—
480
—
591
ps
Without Schmitt
Trigger
—
42
—
42
—
246
—
303
ps
With Schmitt
Trigger
—
429
—
483
—
787
—
968
ps
1.8-V LVTTL /
LVCMOS
Without Schmitt
Trigger
—
378
—
368
—
695
—
855
ps
1.5-V LVCMOS
Without Schmitt
Trigger
—
681
—
658
—
1,334
—
1,642
ps
1.2-V LVCMOS
Without Schmitt
Trigger
—
1,055
—
1,010
—
2,324
—
2,860
ps
3.3-V PCI
Without Schmitt
Trigger
—
0
—
0
—
0
—
0
ps
3.3-V LVTTL
3.3-V LVCMOS
2.5-V LVTTL /
LVCMOS
Table 3–33. External Timing Input Delay tGLOB Adders for GCLK Pins for MAX V Devices (Part 1 of 2)
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
I/O Standard
3.3-V LVTTL
May 2011
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
Without Schmitt
Trigger
—
0
—
0
—
0
—
0
ps
With Schmitt
Trigger
—
387
—
442
—
400
—
493
ps
Altera Corporation
MAX V Device Handbook
3–24
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
Table 3–33. External Timing Input Delay tGLOB Adders for GCLK Pins for MAX V Devices (Part 2 of 2)
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
I/O Standard
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
Without Schmitt
Trigger
—
0
—
0
—
0
—
0
ps
With Schmitt
Trigger
—
387
—
442
—
400
—
493
ps
Without Schmitt
Trigger
—
242
—
242
—
287
—
353
ps
With Schmitt
Trigger
—
429
—
483
—
550
—
677
ps
1.8-V LVTTL /
LVCMOS
Without Schmitt
Trigger
—
378
—
368
—
459
—
565
ps
1.5-V LVCMOS
Without Schmitt
Trigger
—
681
—
658
—
1,111
—
1,368
ps
1.2-V LVCMOS
Without Schmitt
Trigger
—
1,055
—
1,010
—
2,067
—
2,544
ps
3.3-V PCI
Without Schmitt
Trigger
—
0
—
0
—
7
—
9
ps
3.3-V LVCMOS
2.5-V LVTTL /
LVCMOS
Table 3–34. External Timing Output Delay and tOD Adders for Fast Slew Rate for MAX V Devices
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
I/O Standard
3.3-V LVTTL
3.3-V LVCMOS
2.5-V LVTTL / LVCMOS
1.8-V LVTTL / LVCMOS
1.5-V LVCMOS
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
16 mA
—
0
—
0
—
0
—
0
ps
8 mA
—
39
—
58
—
84
—
104
ps
8 mA
—
0
—
0
—
0
—
0
ps
4 mA
—
39
—
58
—
84
—
104
ps
14 mA
—
122
—
129
—
158
—
195
ps
7 mA
—
196
—
188
—
251
—
309
ps
6 mA
—
624
—
624
—
738
—
909
ps
3 mA
—
686
—
694
—
850
—
1,046
ps
4 mA
—
1,188
—
1,184
—
1,376
—
1,694
ps
2 mA
—
1,279
—
1,280
—
1,517
—
1,867
ps
1.2-V LVCMOS
3 mA
—
1,911
—
1,883
—
2,206
—
2,715
ps
3.3-V PCI
20 mA
—
39
—
58
—
4
—
5
ps
LVDS
—
—
122
—
129
—
158
—
195
ps
RSDS
—
—
122
—
129
—
158
—
195
ps
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
3–25
Table 3–35. External Timing Output Delay and tOD Adders for Slow Slew Rate for MAX V Devices
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
I/O Standard
3.3-V LVTTL
3.3-V LVCMOS
2.5-V LVTTL / LVCMOS
1.8-V LVTTL / LVCMOS
1.5-V LVCMOS
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
16 mA
—
5,913
—
6,043
—
6,612
—
6,293
ps
8 mA
—
6,488
—
6,645
—
7,313
—
6,994
ps
8 mA
—
5,913
—
6,043
—
6,612
—
6,293
ps
4 mA
—
6,488
—
6,645
—
7,313
—
6,994
ps
14 mA
—
9,088
—
9,222
—
10,021
—
9,702
ps
7 mA
—
9,808
—
9,962
—
10,881
—
10,562
ps
6 mA
—
21,758
—
21,782
—
21,134
—
20,815
ps
3 mA
—
23,028
—
23,032
—
22,399
—
22,080
ps
4 mA
—
39,068
—
39,032
—
34,499
—
34,180
ps
2 mA
—
40,578
—
40,542
—
36,281
—
35,962
ps
1.2-V LVCMOS
3 mA
—
69,332
—
70,257
—
55,796
—
55,477
ps
3.3-V PCI
20 mA
—
6,488
—
6,645
—
339
—
418
ps
Table 3–36. IOE Programmable Delays for MAX V Devices
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z
Parameter
C4
5M1270Z/ 5M2210Z
C5, I5
C4
Unit
C5, I5
Min
Max
Min
Max
Min
Max
Min
Max
Input Delay from Pin to Internal
Cells = 1
—
1,858
—
2,214
—
1,592
—
1,960
ps
Input Delay from Pin to Internal
Cells = 0
—
569
—
616
—
115
—
142
ps
May 2011
Altera Corporation
MAX V Device Handbook
3–26
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
Maximum Input and Output Clock Rates
Table 3–37 and Table 3–38 list the maximum input and output clock rates for standard
I/O pins in MAX V devices.
Table 3–37. Maximum Input Clock Rate for I/Os for MAX V Devices
I/O Standard
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z/5M1270Z/
5M2210Z
Unit
C4, C5, I5
3.3-V LVTTL
3.3-V LVCMOS
2.5-V LVTTL
2.5-V LVCMOS
Without Schmitt Trigger
304
MHz
With Schmitt Trigger
304
MHz
Without Schmitt Trigger
304
MHz
With Schmitt Trigger
304
MHz
Without Schmitt Trigger
304
MHz
With Schmitt Trigger
304
MHz
Without Schmitt Trigger
304
MHz
With Schmitt Trigger
304
MHz
1.8-V LVTTL
Without Schmitt Trigger
200
MHz
1.8-V LVCMOS
Without Schmitt Trigger
200
MHz
1.5-V LVCMOS
Without Schmitt Trigger
150
MHz
1.2-V LVCMOS
Without Schmitt Trigger
120
MHz
3.3-V PCI
Without Schmitt Trigger
304
MHz
Table 3–38. Maximum Output Clock Rate for I/Os for MAX V Devices
I/O Standard
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z/5M1270Z/
5M2210Z
Unit
C4, C5, I5
MAX V Device Handbook
3.3-V LVTTL
304
MHz
3.3-V LVCMOS
304
MHz
2.5-V LVTTL
304
MHz
2.5-V LVCMOS
304
MHz
1.8-V LVTTL
200
MHz
1.8-V LVCMOS
200
MHz
1.5-V LVCMOS
150
MHz
1.2-V LVCMOS
120
MHz
3.3-V PCI
304
MHz
LVDS
304
MHz
RSDS
200
MHz
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
3–27
LVDS and RSDS Output Timing Specifications
Table 3–39 lists the emulated LVDS output timing specifications for MAX V devices.
Table 3–39. Emulated LVDS Output Timing Specifications for MAX V Devices
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z/5M1270Z/
5M2210Z
Parameter
Mode
Unit
C4, C5, I5
Min
Max
10
—
304
Mbps
9
—
304
Mbps
8
—
304
Mbps
7
—
304
Mbps
6
—
304
Mbps
5
—
304
Mbps
4
—
304
Mbps
3
—
304
Mbps
2
—
304
Mbps
1
—
304
Mbps
tDUTY
—
45
55
%
Total jitter (3)
—
—
0.2
UI
tRISE
—
—
450
ps
tFALL
—
—
450
ps
Data rate (1), (2)
Notes to Table 3–39:
(1) The performance of the LVDS_E_3R transmitter system is limited by the lower of the two—the maximum data rate supported by LVDS_E_3R
I/O buffer or 2x (FMAX of the ALTLVDS_TX instance). The actual performance of your LVDS_E_3R transmitter system must be attained through
the Quartus II timing analysis of the complete design.
(2) For the input clock pin to achieve 304 Mbps, use I/O standard with VCCIO of 2.5 V and above.
(3) This specification is based on external clean clock source.
May 2011
Altera Corporation
MAX V Device Handbook
3–28
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
Table 3–40 lists the emulated RSDS output timing specifications for MAX V devices.
Table 3–40. Emulated RSDS Output Timing Specifications for MAX V Devices
5M40Z/ 5M80Z/ 5M160Z/
5M240Z/ 5M570Z/5M1270Z/
5M2210Z
Parameter
Mode
Unit
C4, C5, I5
Data rate (1)
tDUTY
Min
Max
10
—
200
Mbps
9
—
200
Mbps
8
—
200
Mbps
7
—
200
Mbps
6
—
200
Mbps
5
—
200
Mbps
4
—
200
Mbps
3
—
200
Mbps
2
—
200
Mbps
1
—
200
Mbps
—
45
55
%
Total jitter (2)
—
—
0.2
UI
tRISE
—
—
450
ps
tFALL
—
—
450
ps
Notes to Table 3–40:
(1) For the input clock pin to achieve 200 Mbps, use I/O standard with VCCIO of 1.8 V and above.
(2) This specification is based on external clean clock source.
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 3: DC and Switching Characteristics for MAX V Devices
Timing Model and Specifications
3–29
JTAG Timing Specifications
Figure 3–6 shows the timing waveform for the JTAG signals for the MAX V device
family.
Figure 3–6. JTAG Timing Waveform for MAX V Devices
TMS
TDI
tJCP
tJCH
tJPSU
tJCL
tJPH
TCK
tJPZX
tJPCO
tJPXZ
TDO
tJSSU
Signal
to be
Captured
tJSH
tJSZX
tJSCO
tJSXZ
Signal
to be
Driven
Table 3–41 lists the JTAG timing parameters and values for the MAX V device family.
Table 3–41. JTAG Timing Parameters for MAX V Devices (Part 1 of 2)
Symbol
Parameter
Min
Max
Unit
TCK clock period for V CCIO1 = 3.3 V
55.5
—
ns
TCK clock period for V CCIO1 = 2.5 V
62.5
—
ns
TCK clock period for V CCIO1 = 1.8 V
100
—
ns
TCK clock period for V CCIO1 = 1.5 V
143
—
ns
tJCH
TCK clock high time
20
—
ns
tJCL
TCK clock low time
20
—
ns
tJPSU
JTAG port setup time (2)
8
—
ns
tJPH
JTAG port hold time
10
—
ns
tJPCO
JTAG port clock to output (2)
—
15
ns
tJPZX
JTAG port high impedance to valid output (2)
—
15
ns
tJPXZ
JTAG port valid output to high impedance (2)
—
15
ns
tJSSU
Capture register setup time
8
—
ns
tJSH
Capture register hold time
10
—
ns
tJSCO
Update register clock to output
—
25
ns
tJSZX
Update register high impedance to valid output
—
25
ns
tJCP (1)
May 2011
Altera Corporation
MAX V Device Handbook
3–30
Chapter 3: DC and Switching Characteristics for MAX V Devices
Document Revision History
Table 3–41. JTAG Timing Parameters for MAX V Devices (Part 2 of 2)
Symbol
tJSXZ
Parameter
Min
Max
Unit
—
25
ns
Update register valid output to high impedance
Notes to Table 3–41:
(1) Minimum clock period specified for 10 pF load on the TDO pin. Larger loads on TDO degrades the maximum TCK frequency.
(2) This specification is shown for 3.3-V LVTTL/LVCMOS and 2.5-V LVTTL/LVCMOS operation of the JTAG pins. For 1.8-V LVTTL/LVCMOS and
1.5-V LVCMOS operation, the tJPSU minimum is 6 ns and tJPCO, tJPZX, and tJPXZ are maximum values at 35 ns.
Document Revision History
Table 3–42 lists the revision history for this chapter.
Table 3–42. Document Revision History
Date
Version
Changes
May 2011
1.2
Updated Table 3–2, Table 3–15, Table 3–16, and Table 3–33.
January 2011
1.1
Updated Table 3–37, Table 3–38, Table 3–39, and Table 3–40.
December 2010
1.0
Initial release.
MAX V Device Handbook
May 2011
Altera Corporation
Section II. System Integration in MAX V
Devices
This section provides information about system integration in MAX® V devices.
This section includes the following chapters:
May 2011
■
Chapter 4, Hot Socketing and Power-On Reset in MAX V Devices
■
Chapter 5, Using MAX V Devices in Multi-Voltage Systems
■
Chapter 6, JTAG and In-System Programmability in MAX V Devices
■
Chapter 7, User Flash Memory in MAX V Devices
■
Chapter 8, JTAG Boundary-Scan Testing in MAX V Devices
Altera Corporation
MAX V Device Handbook
II–2
MAX V Device Handbook
Section II: System Integration in MAX V Devices
May 2011
Altera Corporation
4. Hot Socketing and Power-On Reset in
MAX V Devices
December 2010
MV51004-1.0
MV51004-1.0
This chapter provides information about hot-socketing specifications, power-on reset
(POR) requirements, and their implementation in MAX V devices.
MAX V devices offer hot socketing, also known as hot plug-in or hot swap, and
power sequencing support. You can insert or remove a MAX V device in a system
during system operation without causing undesirable effects to the running system
bus. The hot-socketing feature removes some of the difficulty when using MAX V
devices on PCBs that contain a mixture of 3.3-, 2.5-, 1.8-, and 1.5-V devices.
The MAX V hot-socketing feature provides the following:
■
Board or device insertion and removal
■
Support for any power-up sequence
■
Non-intrusive I/O buffers to system buses during hot insertion
This chapter contains the following sections:
■
“MAX V Hot-Socketing Specifications” on page 4–1
■
“Hot-Socketing Feature Implementation in MAX V Devices” on page 4–3
■
“Power-On Reset Circuitry” on page 4–5
MAX V Hot-Socketing Specifications
MAX V devices offer the hot-socketing feature without the need for external
components or special design requirements. The advantages of hot-socketing support
in MAX V devices includes the following:
1
■
The device can be driven before and during power up or power down without
damaging the device.
■
I/O pins remain tri-stated during power up. The device does not drive out before
or during power up, thereby affecting other operating buses.
■
Signal pins do not drive the V CCIO or VCCINT power supplies. External input signals
to the device I/O pins do not power the device VCCIO or VCCINT power supplies
using internal paths. This is true if the V CCINT and VCCIO power supplies are held at
GND.
Altera uses GND as a reference for the hot-socketing and I/O buffers circuitry
designs. To ensure device reliability and compliance to the hot-socketing
specifications, you must connect GND between boards before connecting the VCCINT
and VCCIO power supplies.
© 2010 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.
and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at
www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but
reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
MAX V Device Handbook
December 2010
Subscribe
4–2
Chapter 4: Hot Socketing and Power-On Reset in MAX V Devices
MAX V Hot-Socketing Specifications
Devices Can Be Driven Before Power Up
You can drive signals into the I/O pins and GCLK[3..0] pins of MAX V devices before
or during power up or power down without damaging the device. To simplify the
system-level design, MAX V devices support any power-up or power-down sequence
(VCCIO1, VCCIO2, VCCIO3, VCCIO4, and V CCINT).
I/O Pins Remain Tri-Stated During Power Up
A device that does not support hot socketing may interrupt system operation or cause
contention by driving out before or during power up. In a hot-socketing situation, the
MAX V device’s output buffers are turned off during system power up. MAX V
devices do not drive out until the device attains proper operating conditions and is
fully configured. For more information about turn-on voltages, refer to “Power-On
Reset Circuitry” on page 4–5.
Signal Pins Do Not Drive the VCCIO or VCCINT Power Supplies
MAX V devices do not have a current path from the I/O pins or GCLK[3..0] pins to
the V CCIO or V CCINT power supplies before or during power up. A MAX V device may
be inserted into (or removed from) a system board that is powered up without
damaging or interfering with system-board operation. When hot socketing, MAX V
devices may have a minimal effect on the signal integrity of the backplane.
AC and DC Specifications
You can power up or power down the V CCIO and VCCINT power supplies in any
sequence. During hot socketing, the I/O pin capacitance is less than 8 pF. MAX V
devices meet the following hot-socketing specifications:
1
■
DC specification: | IIOPIN | < 300 A.
■
AC specification: | IIOPIN | < 8 mA for 10 ns or less.
MAX V devices are immune to latch-up when hot socketing. If the TCK JTAG input pin
is driven high during hot socketing, the current on that pin might exceed the
specifications listed above.
IIOPIN is the current for any user I/O pin on the device. The AC specification applies
when the device is being powered up or powered down. This specification takes into
account the pin capacitance but not the board trace and external loading capacitance.
You must consider additional capacitance for trace, connector, and loading separately.
The peak current duration due to power-up transients is 10 ns or less.
The DC specification applies when all VCC supplies to the device are stable in the
powered-up or powered-down conditions.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 4: Hot Socketing and Power-On Reset in MAX V Devices
Hot-Socketing Feature Implementation in MAX V Devices
4–3
Hot-Socketing Feature Implementation in MAX V Devices
The hot-socketing feature tri-states the output buffer during the power-up event
(either the VCCINT or VCCIO power supplies) or power-down event. The hot-socketing
circuitry generates an internal HOTSCKT signal when either VCCINT or VCCIO is below
the threshold voltage during power up or power down. The HOTSCKT signal cuts off
the output buffer to ensure that no DC current leaks through the pin (except for weak
pull-up leaking). When VCC ramps up very slowly during power up, VCC may still be
relatively low even after the POR signal is released and device configuration is
complete.
1
Ensure that VCCINT is within the recommended operating range even though SRAM
download has completed.
Figure 4–1 shows the circuitry for each I/O and clock pin.
Figure 4–1. Hot-Socketing Circuitry for MAX V Devices
Power On
Reset
Monitor
VCCIO
Weak
Pull-Up
Resistor
PAD
Output Enable
Voltage
Tolerance
Control
Hot Socket
Input Buffer
to Logic Array
The POR circuit monitors the VCCINT and V CCIO voltage levels and keeps the I/O pins
tri-stated until the device has completed its flash memory configuration of the SRAM
logic. The weak pull-up resistor (R) from the I/O pin to VCCIO is enabled during
download to keep the I/O pins from floating. The 3.3-V tolerance control circuit
permits the I/O pins to be driven by 3.3 V before VCCIO and/or VCCINT are powered,
and it prevents the I/O pins from driving out when the device is not fully powered or
operational. The hot-socketing circuitry prevents the I/O pins from internally
powering VCCIO and VCCINT when driven by external signals before the device is
powered.
f For more information about the 5.0-V tolerance, refer to the Using MAX V Devices in
Multi-Voltage Systems chapter.
December 2010
Altera Corporation
MAX V Device Handbook
4–4
Chapter 4: Hot Socketing and Power-On Reset in MAX V Devices
Hot-Socketing Feature Implementation in MAX V Devices
Figure 4–2 shows a transistor-level cross section of the MAX V device I/O buffers.
This design ensures that the output buffers do not drive when VCCIO is powered
before V CCINT or if the I/O pad voltage is higher than VCCIO. This also applies for
sudden voltage spikes during hot insertion. The V PAD leakage current charges the
3.3-V tolerant circuit capacitance.
Figure 4–2. Transistor-Level I/O Buffers for MAX V Devices
VPAD
IOE Signal or the
Larger of VCCIO or VPAD
IOE Signal
The Larger of
VCCIO or VPAD
Ensures 3.3-V
Tolerance and
Hot-Socket
Protection
VCCIO
p+
n+
n+
n+
p+
n - well
p - well
p - substrate
The CMOS output drivers in the I/O pins intrinsically provide electrostatic discharge
(ESD) protection. There are two cases to consider for ESD voltage strikes—positive
voltage zap and negative voltage zap.
A positive ESD voltage zap occurs when a positive voltage is present on an I/O pin
due to an ESD charge event. This can cause the N+ (Drain)/ P-Substrate junction of
the N-channel drain to break down and the N+ (Drain)/P-Substrate/N+ (Source)
intrinsic bipolar transistor turn on to discharge ESD current from I/O pin to GND.
The dashed line in Figure 4–3 shows the ESD current discharge path during a positive
ESD zap.
Figure 4–3. ESD Protection During Positive Voltage Zap
I/O
Source
PMOS
Gate
N+
D
Drain
G
P-Substrate
I/O
Drain
NMOS
Gate
N+
S
Source
GND
MAX V Device Handbook
GND
December 2010
Altera Corporation
Chapter 4: Hot Socketing and Power-On Reset in MAX V Devices
Power-On Reset Circuitry
4–5
When the I/O pin receives a negative ESD zap at the pin that is less than –0.7 V (0.7 V
is the voltage drop across a diode), the intrinsic
P-Substrate/N+ drain diode is forward biased. Therefore, the discharge ESD current
path is from GND to the I/O pin, as shown in Figure 4–4.
Figure 4–4. ESD Protection During Negative Voltage Zap
I/O
Source
PMOS
Gate
N+
D
Drain
P-Substrate
I/O
G
Drain
NMOS
Gate
N+
S
Source
GND
GND
Power-On Reset Circuitry
MAX V devices have POR circuits to monitor the V CCINT and VCCIO voltage levels
during power up. The POR circuit monitors these voltages, triggering download from
the non-volatile configuration flash memory block to the SRAM logic, maintaining the
tri-state of the I/O pins (with weak pull-up resistors enabled) before and during this
process. When the MAX V device enters user mode, the POR circuit releases the I/O
pins to user functionality. The POR circuit of the MAX V device does not monitor the
VCCINT voltage level after the device enters into user mode.
Power-Up Characteristics
When power is applied to a MAX V device, the POR circuit monitors V CCINT and
begins SRAM download at 1.55 V for MAX V devices. From this voltage reference, the
SRAM download and entry into user mode takes 200 to 450 µs maximum, depending
on your device density. This period of time is specified as tCONFIG in the power-up
timing section of the DC and Switching Characteristics for MAX V Devices chapter.
Entry into user mode is gated by whether all the VCCIO banks are powered with
sufficient operating voltage. If VCCINT and VCCIO are powered simultaneously, the
device enters user mode within the tCONFIG specifications. If V CCIO is powered more
than tCONFIG after VCCINT, the device does not enter user mode until 2 µs after all VCCIO
banks are powered.
December 2010
Altera Corporation
MAX V Device Handbook
4–6
Chapter 4: Hot Socketing and Power-On Reset in MAX V Devices
Document Revision History
For MAX V devices, the POR circuitry does not monitor the VCCINT and VCCIO voltage
levels after the device enters user mode. If there is a VCCINT voltage sag below 1.4 V
during user mode, the functionality of the device is not guaranteed and you must
power down VCCINT to 250 mV for a minimum of 10 µs before powering VCCINT and
VCCIO up again. After V CCINT rises from 250 mV back to approximately 1.55 V, the
SRAM download restarts and the device begins to operate after the tCONFIG time has
passed.
Figure 4–5 shows the voltages for POR of MAX V devices during power up into user
mode and from user mode to power down or brown out.
1
All VCCINT and VCCIO power supplies of all banks must be powered on before entering
user mode.
Figure 4–5. Power-Up Characteristics for MAX V Devices (Note 1), (2)
MAX V Device
VCCINT
3.3 V
Approximate Voltage
for SRAM Download Start
VCCINT must be powered down
to 250 mV if the VCCINT
dips below this level
1.8 V
1.55 V
1.4 V
minimum 10 µs
tCONFIG
250 mV
Tri-State
User Mode
Operation
tCONFIG
Tri-State
User Mode
Operation
Notes to Figure 4–5:
(1) Time scale is relative.
(2) For this figure, all the VCCIO banks are powered up simultaneously with the VCCINT profile shown. If this is not the case, tCONFIG stretches out until all
VCCIO banks are powered.
1
After SRAM configuration, all registers in the device are cleared and released into
user function before the I/O tri-states are released. To release clears after the tri-states
are released, use the DEV_CLRn pin option. To hold the tri-states beyond the power-up
configuration time, use the DEV_OE pin option.
Document Revision History
Table 4–1 lists the revision history for this chapter.
Table 4–1. Document Revision History
Date
December 2010
MAX V Device Handbook
Version
1.0
Changes
Initial release.
December 2010
Altera Corporation
5. Using MAX V Devices in Multi-Voltage
Systems
December 2010
MV51005-1.0
MV51005-1.0
This chapter describes how to implement Altera® devices in multi-voltage systems
without damaging the device or the system.
Technological advancements in deep submicron processes have lowered the supply
voltage levels of semiconductor devices, creating a design environment where devices
on a system board may potentially use many different supply voltages such as 5.0, 3.3,
2.5, 1.8, 1.5, and 1.2 V, which can ultimately lead to voltage conflicts.
To accommodate interfacing with a variety of devices on system boards, MAX® V
devices have MultiVolt I/O interfaces that allow devices in a mixed-voltage design
environment to communicate directly with MAX V devices. The MultiVolt interface
separates the power supply voltage (V CCINT) from the output voltage (VCCIO),
allowing MAX V devices to interface with other devices using a different voltage level
on the same PCB. The 1.8-V input directly powers the core of the MAX V devices.
f For more information about hot socketing and power-on reset (POR), refer to the Hot
Socketing and Power-On Reset in MAX V Devices chapter.
This chapter contains the following sections:
■
“I/O Standards” on page 5–1
■
“MultiVolt I/O Operation” on page 5–3
■
“5.0-V Device Compatibility” on page 5–3
■
“Recommended Operating Conditions for 5.0-V Compatibility” on page 5–7
■
“Power-Up Sequencing” on page 5–8
I/O Standards
The I/O buffer of MAX V devices is programmable and supports a wide range of I/O
voltage standards. You can program each I/O bank in a MAX V device to comply
with a different I/O standard. You can configure all I/O banks with the following
standards:
■
3.3-V LVTTL/LVCMOS
■
2.5-V LVTTL/LVCMOS
■
1.8-V LVTTL/LVCMOS
■
1.5-V LVCMOS
■
1.2-V LVCMOS
■
Emulated LVDS output (LVDS_E_3R)
■
Emulated RSDS output (RSDS_E_3R)
© 2010 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.
and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at
www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but
reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
MAX V Device Handbook
December 2010
Subscribe
5–2
Chapter 5: Using MAX V Devices in Multi-Voltage Systems
I/O Standards
The Schmitt trigger input option is supported by the 3.3-V and 2.5-V I/O standards.
The I/O Bank 3 also includes the 3.3-V PCI I/O standard interface capability on the
5M1270Z and 5M2210Z devices. Figure 5–1 shows the I/O standards supported by
MAX V devices.
Figure 5–1. I/O Standards Supported by MAX V Devices (Note 1), (2), (3), (4), (5)
I/O Bank 2
I/O Bank 3
also supports
the 3.3-V PCI
I/O Standard
I/O Bank 1
All I/O Banks Support
■ 3.3-V LVTTL/LVCMOS
■ 2.5-V LVTTL/LVCMOS
■ 1.8-V LVTTL/LVCMOS
■ 1.5-V LVCMOS
■ 1.2-V LVCMOS
■ Emulated LVDS output
(LVDS_E_3R)
■ Emulated RSDS output
(RSDS_E_3R)
I/O Bank 3
Individual
Power Bus
I/O Bank 4
Notes to Figure 5–1:
(1) Figure 5–1 is a top view of the silicon die.
(2) Figure 5–1 is a graphical representation only. For the exact pin locations, refer to the pin list and the Quartus® II software.
(3) 5M40Z, 5M80Z, 5M160Z, 5M240Z, and 5M570Z devices only have two I/O banks.
(4) The 3.3-V PCI I/O standard is only supported in 5M1270Z and 5M2210Z devices.
(5) The Schmitt trigger input option for 3.3-V and 2.5-V I/O standards is supported for all I/O pins.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 5: Using MAX V Devices in Multi-Voltage Systems
MultiVolt I/O Operation
5–3
MultiVolt I/O Operation
MAX V devices allow the device core and I/O blocks to be powered-up with separate
supply voltages. The VCCINT pins supply power to the device core and the VCCIO pins
supply power to the device I/O buffers. The VCCINT pins are powered-up with 1.8 V
for MAX V devices. All the VCCIO pins for a given I/O bank that have MultiVolt
capability must be supplied from the same voltage level (for example, 5.0, 3.3, 2.5, 1.8,
1.5, or 1.2 V). Figure 5–2 shows how to implement a multiple-voltage system for
MAX V devices.
Figure 5–2. Implementing a Multi-Voltage System with a MAX V Device (Note 1), (2)
1.8-V
Power Supply
VCCINT
5.0-V
Device
VCCIO
MAX V
Device
VCCIO
3.3-, 2.5-, 1.8-,
1.5-, 1.2-V
Device
Notes to Figure 5–2:
(1) MAX V devices can drive a 5.0-V transistor-to-transistor logic (TTL) input when VCCIO = 3.3 V. To drive a 5.0-V
CMOS, you must have an open-drain setting with an internal I/O clamp diode and external resistor.
(2) MAX V devices can be 5.0-V tolerant with the use of an external resistor and the internal I/O clamp diode on
5M1270Z and 5M2210Z devices.
5.0-V Device Compatibility
A MAX V device can drive a 5.0-V TTL device by connecting the VCCIO pins of the
MAX V device to 3.3 V. This is possible because the output high voltage (VOH) of a
3.3-V interface meets the minimum high-level voltage of 2.4 V of a 5.0-V TTL device.
A MAX V device may not correctly interoperate with a 5.0-V CMOS device if the
output of the MAX V device is connected directly to the input of the 5.0-V CMOS
device. If the MAX V device‘s VOUT is greater than V CCIO, the PMOS pull-up transistor
still conducts if the pin is driving high, preventing an external pull-up resistor from
pulling the signal to 5.0 V. To make MAX V device outputs compatible with 5.0-V
CMOS devices, configure the output pins as open-drain pins with the I/O clamp
diode enabled and use an external pull-up resistor.
December 2010
Altera Corporation
MAX V Device Handbook
5–4
Chapter 5: Using MAX V Devices in Multi-Voltage Systems
5.0-V Device Compatibility
Figure 5–3 shows MAX V device compatibility with 5.0-V CMOS devices.
Figure 5–3. MAX V Device Compatibility with 5.0-V CMOS Devices
5.0 V ± 0.5 V
3.3 V
V CCIO
V CCIO
V CCIO
(1)
REXT
Open Drain
Model as RINT
VOUT
A
5.0-V CMOS
Device
VIN
VSS
Note to Figure 5–3:
(1) This diode is only active after power-up. MAX V devices require an external diode if driven by 5.0 V before
power-up.
The open-drain pin never drives high, only low or tri-state. When the open-drain pin
is active, it drives low. When the open-drain pin is inactive, the pin is tri-stated and
the trace pulls up to 5.0 V by the external resistor. The purpose of enabling the I/O
clamp diode is to protect the MAX V device’s I/O pins. The 3.3-V V CCIO supplied to
the I/O clamp diodes causes the voltage at point A to clamp at 4.0 V, which meets the
MAX V device’s reliability limits when the trace voltage exceeds 4.0 V. The device
operates successfully because a 5.0-V input is within its input specification.
1
The I/O clamp diode is only supported in the 5M1270Z and 5M2210Z devices’ I/O
Bank 3. You must have an external protection diode for the other I/O banks in the
5M1270Z and 5M2210Z devices and all the I/O pins in the 5M40Z, 5M80Z, 5M160Z,
5M240Z, and 5M570Z devices.
The pull-up resistor value must be small enough for a sufficient signal rise time, but
large enough so that it does not violate the IOL (output low) specification of the
MAX V devices.
The maximum MAX V device IOL depends on the programmable drive strength of the
I/O output. Table 5–1 lists the programmable drive strength settings that are available
for the 3.3-V LVTTL/LVCMOS I/O standard for MAX V devices. The Quartus II
software uses the maximum current strength as the default setting. The PCI I/O
standard is always set to 20 mA with no alternate setting.
Table 5–1. 3.3-V LVTTL/LVCMOS Programmable Drive Strength (Part 1 of 2)
I/O Standard
3.3-V LVTTL
MAX V Device Handbook
IOH/IOL Current Strength Setting (mA)
16
8
December 2010
Altera Corporation
Chapter 5: Using MAX V Devices in Multi-Voltage Systems
5.0-V Device Compatibility
5–5
Table 5–1. 3.3-V LVTTL/LVCMOS Programmable Drive Strength (Part 2 of 2)
I/O Standard
IOH/IOL Current Strength Setting (mA)
8
3.3-V LVCMOS
4
To compute the required value of REXT, first calculate the model of the open-drain
transistors on the MAX V device. You can model this output resistor (REXT) by
dividing V OL by IOL (REXT = VOL/IOL). Table 5–2 lists the maximum V OL for the 3.3-V
LVTTL/LVCMOS I/O standard for MAX V devices.
f For more information about I/O standard specifications, refer to the DC and Switching
Characteristics for MAX V Devices chapter.
Table 5–2. 3.3-V LVTTL/LVCMOS Maximum V OL
I/O Standard
Voltage (V)
3.3-V LVTTL
0.45
3.3-V LVCMOS
0.20
Select REXT so that the MAX V device’s IOL specification is not violated. You can
compute the required pull-up resistor value of REXT by using the equation:
REXT = (VCC/IOL) – RINT. For example, if an I/O pin is configured as a 3.3-V LVTTL
with a 16 mA drive strength, given that the maximum power supply (VCC) is 5.5 V,
you can calculate the value of REXT as follows:
Equation 5–1.
 5.5 V – 0.45 V 
R EX T = ----------------------------------------- = 315.6 
16 mA
This resistor value computation assumes worst-case conditions. You can adjust the
REXT value according to the device configuration drive strength. Additionally, if your
system does not see a wide variation in voltage-supply levels, you can adjust these
calculations accordingly.
Because MAX V devices are 3.3-V, 32-bit, 66-MHz PCI compliant, the input circuitry
accepts a maximum high-level input voltage (VIH) of 4.0 V. To drive a MAX V device
with a 5.0-V device, you must connect a resistor (R2) between the MAX V device and
the 5.0-V device.
December 2010
Altera Corporation
MAX V Device Handbook
5–6
Chapter 5: Using MAX V Devices in Multi-Voltage Systems
5.0-V Device Compatibility
Figure 5–4 shows how to drive a MAX V PCI-compliant device with a 5.0-V device.
Figure 5–4. Driving a MAX V PCI-Compliant Device with a 5.0-V Device
MAX V Device
5.0-V Device
3.3 V
5.0 V ± 0.5 V
V CCIO
V CC
V CCIO
PCI Clamp
I
(1)
I
R2
Model as R 1
B
Note to Figure 5–4:
(1) This diode is only active after power-up. MAX V devices require an external diode if driven by 5.0 V before
power-up.
If VCCIO for the MAX V devices is 3.3 V and you enabled the I/O clamp diode, the
voltage at point B in Figure 5–4 is 4.0 V, which meets the MAX V devices reliability
limits when the trace voltage exceeds 4.0 V. To limit large current draw from the 5.0-V
device, R2 must be small enough for a fast signal rise time and large enough so that it
does not violate the high-level output current (IOH) specifications of the devices
driving the trace.
To compute the required value of R2 , first calculate the model of the pull-up
transistors on the 5.0-V device. You can model this output resistor (R1) by dividing the
5.0-V device supply voltage (VCC) by IOH: R1 = V CC/IOH.
Figure 5–5 shows an example of typical output drive characteristics of a 5.0 V device.
Figure 5–5. Output Drive Characteristics of a 5.0-V Device
150
IOL
135
120
Typical IO
Output
Current (mA)
VCCINT = 5.0 V
VCCIO = 5.0 V
90
60
IOH
30
1
2
3
4
5
VO Output Voltage (V)
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 5: Using MAX V Devices in Multi-Voltage Systems
Recommended Operating Conditions for 5.0-V Compatibility
5–7
As shown in Figure 5–5, R1 = 5.0 V/135 mA.
The values usually shown in the data sheets reflect typical operating conditions.
Subtract 20% from the data sheet value for guard band. When you subtract the 20%
from the previous example, the R1 value is 30.
Select R2 so that the MAX V device’s IOH specification is not violated. For example, if
the above device has a maximum IOH of 8 mA, given the I/O clamp diode,
VIN = VCCIO + 0.7 V = 3.7 V. Given that the maximum supply load of a 5.0-V device
(VCC) is 5.5 V, calculate value of R2 as follows:
Equation 5–2.
 5.5 V – 3.7 V  –  8 mA  30  
R 2 = ------------------------------------------------------------------------------------ = 194 
8 mA
This analysis assumes worst-case conditions. If your system does not see a wide
variation in voltage-supply levels, you can adjust these calculations accordingly.
Because 5.0-V device tolerance in MAX V devices requires the use of the I/O clamp,
and this clamp is activated only after power-up, 5.0-V signals may not be driven into
the device until it is configured. The I/O clamp diode is only supported in the
5M1270Z and 5M2210Z devices’ I/O Bank 3. You must have an external protection
diode for the other I/O banks for the 5M1270Z and 5M2210Z devices and all the I/O
pins in the 5M40Z, 5M80Z, 5M160Z, 5M240Z, and 5M570Z devices.
Recommended Operating Conditions for 5.0-V Compatibility
As mentioned earlier, a 5.0-V tolerance can be supported with the I/O clamp diode
enabled with external series/pull-up resistance. To guarantee long term reliability of
the device’s I/O buffer, there are restrictions on the signal duty cycle that drive the
MAX V I/O, which is based on the maximum clamp current. Table 5–3 lists the
maximum signal duty cycle for the 3.3-V VCCIO given a PCI clamp current-handling
capability.
Table 5–3. Maximum Signal Duty Cycle
VIN (V) (1)
ICH (mA) (2)
Max Duty Cycle (%)
4.0
5.00
100
4.1
11.67
90
4.2
18.33
50
4.3
25.00
30
4.4
31.67
17
4.5
38.33
10
4.6
45.00
5
Notes to Table 5–3:
(1) VIN is the voltage at the package pin.
(2) The ICH is calculated with a 3.3-V VCCIO. A higher VCCIO value will have a lower ICH value with the same VIN.
December 2010
Altera Corporation
MAX V Device Handbook
5–8
Chapter 5: Using MAX V Devices in Multi-Voltage Systems
Power-Up Sequencing
1
For signals with a duty cycle greater than 30% on MAX V input pins, Altera
recommends using a V CCIO voltage of 3.0 V to guarantee long-term I/O reliability. For
signals with a duty cycle less than 30%, the V CCIO voltage can be 3.3 V.
Power-Up Sequencing
MAX V devices are designed to operate in multi-voltage environments where it may
be difficult to control power sequencing. Therefore, MAX V devices are designed to
tolerate any possible power-up sequence. Either VCCINT or VCCIO can initially supply
power to the device and 3.3-, 2.5-, 1.8-, 1.5-, or 1.2-V input signals can drive the
devices without special precautions before VCCINT or VCCIO is applied. MAX V devices
can operate with a VCCIO voltage level that is higher than the VCCINT level.
When V CCIO and VCCINT are supplied from different power sources to a MAX V
device, a delay between VCCIO and V CCINT may occur. Normal operation does not
occur until both power supplies are in their recommended operating range. When
VCCINT is powered-up, the IEEE Std. 1149.1 JTAG circuitry is active. If TMS and TCK are
connected to VCCIO and V CCIO is not powered-up, the JTAG signals are left floating.
Thus, any transition on TCK can cause the state machine to transition to an unknown
JTAG state, leading to incorrect operation when VCCIO is finally powered-up. To
disable the JTAG state during the power-up sequence, pull TCK low to ensure that an
inadvertent rising edge does not occur on TCK.
Document Revision History
Table 5–4 lists the revision history for this chapter.
Table 5–4. Document Revision History
Date
December 2010
MAX V Device Handbook
Version
1.0
Changes
Initial release.
December 2010
Altera Corporation
6. JTAG and In-System Programmability
in MAX V Devices
May 2011
MV51006-1.1
MV51006-1.1
This chapter describes the IEEE Standard 1149.1 JTAG BST circuitry that is supported
in MAX® V devices and how you can enable concurrent in-system programming of
multiple devices in a minimum time with the IEEE Standard 1532 in-system
programmability (ISP). This chapter also describes the programming sequence, types
of programming with the Quartus® II software or external hardware, and design
security.
This chapter includes the following sections:
■
“IEEE Std. 1149.1 Boundary-Scan Support” on page 6–1
■
“In-System Programmability” on page 6–5
IEEE Std. 1149.1 Boundary-Scan Support
All MAX V devices provide JTAG BST circuitry that complies with the
IEEE Std. 1149.1-2001 specification. You can only perform JTAG boundary-scan
testing after you have fully powered the VCCINT and all VCCIO banks and a certain
amount of configuration time (tCONFIG) have passed. For in-system programming,
MAX V devices can use the JTAG port with either the Quartus II software or
hardware with Programmer Object File (.pof), Jam™ Standard Test and Programming
Language (STAPL) Format File (.jam), or Jam Byte Code Files (.jbc).
JTAG pins support 1.5-V, 1.8-V, 2.5-V, and 3.3-V I/O standards. The VCCIO of the bank
where it is located determines the supported voltage level and standard. The
dedicated JTAG pins reside in Bank 1 of all MAX V devices.
Table 6–1 lists the JTAG instructions supported in MAX V devices.
Table 6–1. JTAG Instructions for MAX V Devices (Part 1 of 2)
JTAG Instruction
Instruction Code
Description
SAMPLE/PRELOAD
00 0000 0101
Allows you to capture and examine a snapshot of signals at the
device pins if the device is operating in normal mode. Permits an
initial data pattern to be an output at the device pins.
EXTEST (1)
00 0000 1111
Allows you to test the external circuitry and board-level
interconnects by forcing a test pattern at the output pins and
capturing test results at the input pins.
11 1111 1111
Places the 1-bit bypass register between the TDI and TDO pins,
which allows the boundary-scan test (BST) data to pass
synchronously through target devices to adjacent devices during
normal device operation.
00 0000 0111
Selects the 32-bit USERCODE register and places it between the TDI
and TDO pins, allowing you to shift the USERCODE register out of the
TDO pin serially. If you do not specify the USERCODE in the Quartus II
software, the 32-bit USERCODE register defaults to all 1’s.
BYPASS
USERCODE
© 2011 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.
and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at
www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but
reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
MAX V Device Handbook
May 2011
Subscribe
6–2
Chapter 6: JTAG and In-System Programmability in MAX V Devices
IEEE Std. 1149.1 Boundary-Scan Support
Table 6–1. JTAG Instructions for MAX V Devices (Part 2 of 2)
JTAG Instruction
Instruction Code
Description
00 0000 0110
Selects the IDCODE register and places it between the TDI and TDO
pins, allowing you to shift the IDCODE register out of the TDO pin
serially.
00 0000 1011
Places the 1-bit bypass register between the TDI and TDO pins,
which allows the BST data to pass synchronously through target
devices to adjacent devices if the device is operating in normal mode
and tri-stating all the I/O pins.
CLAMP (1)
00 0000 1010
Places the 1-bit bypass register between the TDI and TDO pins,
which allows the BST data to pass synchronously through target
devices to adjacent devices during normal device operation and
holding I/O pins to a state defined by the data in the boundary-scan
register.
USER0
00 0000 1100
Allows you to define the scan chain between the TDI and TDO pins in
the MAX V logic array. Use this instruction for custom logic and
JTAG interfaces.
USER1
00 0000 1110
Allows you to define the scan chain between the TDI and TDO pins in
the MAX V logic array. Use this instruction for custom logic and
JTAG interfaces.
IDCODE
HIGHZ (1)
IEEE 1532
instructions
For the instruction codes
of the IEEE 1532
instructions, refer to the
IEEE 1532 BSDL Files
page of the Altera
website.
IEEE 1532 in-system concurrent (ISC) instructions used if
programming a MAX V device through the JTAG port.
Note to Table 6–1:
(1) HIGHZ, CLAMP, and EXTEST instructions do not disable weak pull-up resistors or bus hold features.
w
MAX V Device Handbook
You must not issue unsupported JTAG instructions to the MAX V device because this
may put the device into an unknown state, requiring a power cycle to recover device
operation.
May 2011
Altera Corporation
Chapter 6: JTAG and In-System Programmability in MAX V Devices
IEEE Std. 1149.1 Boundary-Scan Support
6–3
The MAX V device instruction register length is 10 bits and the USERCODE register
length is 32 bits. Table 6–2 and Table 6–3 list the boundary-scan register length and
device IDCODE information for MAX V devices.
Table 6–2. Boundary-Scan Register Length for MAX V Devices
Device
Boundary-Scan Register Length
5M40Z
240
5M80Z
240
5M160Z
240
5M240Z (1)
240
5M240Z (2)
480
5M570Z
480
5M1270Z (3)
636
5M1270Z (4)
816
5M2210Z
816
Notes to Table 6–2:
(1) Not applicable to T144 package of the 5M240Z device.
(2) Only applicable to T144 package of the 5M240Z device.
(3) Not applicable to F324 package of the 5M1270Z device.
(4) Only applicable to F324 package of the 5M1270Z device.
Table 6–3. 32-Bit IDCODE for MAX V Devices
Binary IDCODE (32 Bits) (1)
Device
Version
(4 Bits)
Manufacturer
Identity (11 Bits)
LSB
(1 Bit) (2)
HEX IDCODE
Part Number
5M40Z
0000
0010 0000 1010 0101
000 0110 1110
1
0x020A50DD
5M80Z
0000
0010 0000 1010 0101
000 0110 1110
1
0x020A50DD
5M160Z
0000
0010 0000 1010 0101
000 0110 1110
1
0x020A50DD
5M240Z (3)
0000
0010 0000 1010 0101
000 0110 1110
1
0x020A50DD
5M240Z (4)
0000
0010 0000 1010 0110
000 0110 1110
1
0x020A60DD
5M570Z
0000
0010 0000 1010 0110
000 0110 1110
1
0x020A60DD
5M1270Z (5)
0000
0010 0000 1010 0011
000 0110 1110
1
0x020A30DD
5M1270Z (6)
0000
0010 0000 1010 0100
000 0110 1110
1
0x020A40DD
5M2210Z
0000
0010 0000 1010 0100
000 0110 1110
1
0x020A40DD
Notes to Table 6–2:
(1) The MSB is on the left.
(2) The LSB for IDCODE is always 1.
(3) Not applicable to T144 package of the 5M240Z device.
(4) Only applicable to T144 package of the 5M240Z device.
(5) Not applicable to F324 package of the 5M1270Z device.
(6) Only applicable to F324 package of the 5M1270Z device.
f For JTAG direct current (DC) characteristics, refer to the DC and Switching
Characteristics for MAX V Devices chapter.
May 2011
Altera Corporation
MAX V Device Handbook
6–4
Chapter 6: JTAG and In-System Programmability in MAX V Devices
IEEE Std. 1149.1 Boundary-Scan Support
f For more information about JTAG BST, refer to the JTAG Boundary-Scan Testing for
MAX V Devices chapter.
JTAG Block
If you issue either the USER0 or USER1 instruction to the JTAG test access port (TAP)
controller, the MAX V JTAG block feature allows you to access the JTAG TAP
controller and state signals. The USER0 and USER1 instructions bring the JTAG
boundary-scan chain (TDI) through the user logic instead of the boundary-scan cells
(BSCs) of MAX V devices. Each USER instruction allows for one unique user-defined
JTAG chain into the logic array.
Parallel Flash Loader
MAX V devices have the ability to interface JTAG to non-JTAG devices and are
suitable to use with the general flash memory devices that require programming
during the in-circuit test. You can use the flash memory devices for FPGA
configuration or be part of the system memory. In many cases, you can use the
MAX V device as a bridge device that controls configuration between FPGA and flash
devices. Unlike ISP-capable CPLDs, bulk flash devices do not have JTAG TAP pins or
connections. For small flash devices, it is common to use the serial JTAG scan chain of
a connected device to program the non-JTAG flash device but this is slow, inefficient,
and impractical for large parallel flash devices. Using the MAX V JTAG block as a
parallel flash loader (PFL) with the Quartus II software to program and verify flash
contents provides a fast and cost-effective means of in-circuit programming during
testing.
f For more information about PFL, refer to the Parallel Flash Loader Megafunction User
Guide.
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 6: JTAG and In-System Programmability in MAX V Devices
In-System Programmability
6–5
Figure 6–1 shows how you can use the MAX V JTAG block as a PFL.
Figure 6–1. PFL for MAX V Devices
MAX V Device
Flash
Memory Device
Altera FPGA
DQ[7..0]
A[20..0]
OE
WE
CE
RY/BY
DQ[7..0]
A[20..0]
OE
WE
CE
RY/BY
TDI
TMS
TCK
TDO
TDO_U
TDI_U
TMS_U
TCK_U
SHIFT_U
CLKDR_U
UPDATE_U
RUNIDLE_U
USER1_U
PFL
Configuration
Logic
CONF_DONE
nSTATUS
nCE
DATA0
nCONFIG
DCLK
(1), (2)
Notes to Figure 6–1:
(1) This block is implemented in logic elements (LEs).
(2) This function is supported in the Quartus II software.
In-System Programmability
You can program MAX V devices in-system through the industry standard 4-pin
IEEE Std. 1149.1 interface. ISP offers quick and efficient iterations during design
development and debugging cycles. The flash-based SRAM configuration elements
configure the logic, circuitry, and interconnects in the MAX V architecture. Each time
the device is powered up, the configuration data is loaded into the SRAM elements.
The process of loading the SRAM data is called configuration. The on-chip
configuration flash memory (CFM) block stores the configuration data of the SRAM
element. The CFM block stores the configuration pattern of your design in a
reprogrammable flash array. During ISP, the MAX V JTAG and ISP circuitry programs
the design pattern into the non-volatile flash array of the CFM block.
The MAX V JTAG and ISP controller internally generate the high programming
voltages required to program the CFM cells, allowing in-system programming with
any of the recommended operating external voltage supplies. You can configure the
ISP anytime after you have fully powered V CCINT and all V CCIO banks, and the device
has completed the configuration power-up time. By default, during in-system
programming, the I/O pins are tri-stated and weakly pulled-up to VCCIO banks to
eliminate board conflicts. The in-system programming clamp and real-time ISP
feature allow user control of the I/O state or behavior during ISP.
For more information, refer to “In-System Programming Clamp” on page 6–7 and
“Real-Time ISP” on page 6–8.
These devices also offer an ISP_DONE bit that provides safe operation if in-system
programming is interrupted. This ISP_DONE bit, which is the last bit programmed,
prevents all I/O pins from driving until the bit is programmed.
May 2011
Altera Corporation
MAX V Device Handbook
6–6
Chapter 6: JTAG and In-System Programmability in MAX V Devices
In-System Programmability
IEEE 1532 Support
The JTAG circuitry and ISP instruction set in MAX V devices are compliant to the
IEEE-1532-2002 programming specification. This provides industry-standard
hardware and software for in-system programming among multiple vendor
programmable logic devices (PLDs) in a JTAG chain.
f For more information about MAX V 1532 Boundary-Scan Description Language
(.bsd) files, refer to the IEEE 1532 BSDL Files page of the Altera website.
Jam Standard Test and Programming Language
You can use the Jam STAPL to program MAX V devices with in-circuit testers, PCs, or
embedded processors. The Jam byte code is also supported for MAX V devices. These
software programming protocols provide a compact embedded solution for
programming MAX V devices.
f For more information, refer to AN 425: Using Command-Line Jam STAPL Solution for
Device Programming.
Programming Sequence
During in-system programming, 1532 instructions, addresses, and data are shifted
into the MAX V device through the TDI input pin. Data is shifted out through the TDO
output pin and compared with the expected data.
To program a pattern into the device, follow these steps:
1. Enter ISP—The enter ISP stage ensures that the I/O pins transition smoothly from
user mode to ISP mode.
2. Check ID—The silicon ID is checked before any Program or Verify process. The
time required to read this silicon ID is relatively small compared to the overall
programming time.
3. Sector Erase—Erasing the device in-system involves shifting in the instruction to
erase the device and applying an erase pulse or pulses. The erase pulse is
automatically generated internally by waiting in the run, test, or idle state for the
specified erase pulse time of 500 ms for the CFM block and 500 ms for each sector
of the user flash memory (UFM) block.
4. Program—Programming the device in-system involves shifting in the address,
data, and program instruction and generating the program pulse to program the
flash cells. The program pulse is automatically generated internally by waiting in
the run/test/idle state for the specified program pulse time of 75 µs. This process
is repeated for each address in the CFM and UFM blocks.
5. Verify—Verifying a MAX V device in-system involves shifting in addresses,
applying the verify instruction to generate the read pulse, and shifting out the data
for comparison. This process is repeated for each CFM and UFM address.
6. Exit ISP—An exit ISP stage ensures that the I/O pins transition smoothly from ISP
mode to user mode.
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 6: JTAG and In-System Programmability in MAX V Devices
In-System Programmability
6–7
A stand-alone verification of a programmed pattern involves only steps 1, 2, 5, and 6.
These steps are automatically executed by third-party programmers, the Quartus II
software, or the Jam STAPL and Jam Byte-Code Players.
Table 6–4 lists the programming times for MAX V devices with in-circuit testers to
execute the algorithm vectors in hardware. Because of data processing and data
transfer limitations, software-based programming tools used with download cables
are slightly slower.
Table 6–4. Family Programming Times for MAX V Devices
5M40Z/
5M80Z/
5M160Z/
5M240Z (1)
5M240Z
(2)
5M570Z
5M1270Z (3)
5M1270Z (4)
5M2210Z
Unit
Erase + Program (1 MHz)
1.72
2.16
2.16
2.90
3.92
3.92
sec
Erase + Program (10 MHz)
1.65
1.99
1.99
2.58
3.40
3.40
sec
Verify (1 MHz)
0.09
0.17
0.17
0.30
0.49
0.49
sec
Verify (10 MHz)
0.01
0.02
0.02
0.03
0.05
0.05
sec
Complete Program Cycle (1 MHz)
1.81
2.33
2.33
3.20
4.41
4.41
sec
Complete Program Cycle (10 MHz)
1.66
2.01
2.01
2.61
3.45
3.45
sec
Description
Notes to Table 6–4:
(1) Not applicable to T144 package of the 5M240Z device.
(2) Only applicable to T144 package of the 5M240Z device.
(3) Not applicable to F324 package of the 5M1270Z device.
(4) Only applicable to F324 package of the 5M1270Z device.
User Flash Memory Programming
The Quartus II software (with the use of .pof, .jam, or .jbc files) supports
programming of the UFM block independent of the logic array design pattern stored
in the CFM block. This allows updating or reading UFM contents through ISP without
altering the current logic array design, or vice versa. By default, these programming
files and methods program the entire flash memory contents, which includes the CFM
block and UFM contents. The stand-alone embedded Jam STAPL Player and Jam
Byte-Code Player provide action commands for programming or reading the entire
flash memory (UFM and CFM together) or each independently.
f For more information, refer to AN 425: Using the Command-Line Jam STAPL Solution for
Device Programming.
In-System Programming Clamp
By default, the IEEE 1532 instruction used for entering ISP automatically tri-states all
I/O pins with weak pull-up resistors for the duration of the ISP sequence. However,
some systems may require certain pins on MAX V devices to maintain a specific DC
logic level during an in-field update. For these systems, you can use the optional insystem programming clamp instruction in the MAX V circuitry to control I/O
May 2011
Altera Corporation
MAX V Device Handbook
6–8
Chapter 6: JTAG and In-System Programmability in MAX V Devices
In-System Programmability
behavior during the ISP sequence. The in-system programming clamp instruction
allows the device to sample and sustain the value on an output pin (an input pin
remains tri-stated if sampled) or to set a logic high, logic low, or tri-state value
explicitly on any pin. Setting these options is controlled on an individual pin basis
with the Quartus II software.
f For more information, refer to AN 630: Real-Time ISP and ISP Clamp for Altera CPLDs.
Real-Time ISP
For systems that require more than the DC logic level control of I/O pins, the
real-time ISP feature allows you to update the CFM block with a new design image,
while the current design continues to operate in the SRAM logic array and I/O pins.
A new programming file is updated into the MAX V device without halting the
original operation of your design, saving down-time costs for remote or field
upgrades. The updated CFM block configures the new design into the SRAM after the
next power cycle. You can execute an immediate SRAM configuration without a
power cycle with a specific sequence of ISP commands. The SRAM configuration
without a power cycle takes a specific amount of time (tCONFIG). During this time, the
I/O pins are tri-stated and weakly pulled-up to VCCIO.
Design Security
All MAX V devices contain a programmable security bit that controls access to the
data programmed into the CFM block. If this bit is programmed, you cannot copy or
retrieve the design programming information stored in the CFM block. This feature
provides a high-level design security because programmed data within flash memory
cells is invisible. You can only reset the security bit that controls this function and
other programmed data if the device is erased. The SRAM is also invisible and cannot
be accessed regardless of the security bit setting. The security bit does not protect the
UFM block data, and the UFM is accessible through JTAG or logic array connections.
Programming with External Hardware
You can program MAX V devices by downloading the information through in-circuit
testers, embedded processors, the Altera® ByteBlaster™ II, EthernetBlaster II,
EthernetBlaster, and USB-Blaster™ cables. You need to power up these cable’s
VCC(TRGT) with V CCIO of Bank 1.
f For more information about the respective cables, refer to the Cable & Adapter
Drivers Information page.
BP Microsystems, System General, and other programming hardware manufacturers
provide programming support for Altera devices. For device support information,
refer to their websites.
MAX V Device Handbook
May 2011
Altera Corporation
Chapter 6: JTAG and In-System Programmability in MAX V Devices
Document Revision History
6–9
Document Revision History
Table 6–5 lists the revision history for this chapter.
Table 6–5. Document Revision History
Date
Version
Changes
May 2011
1.1
Updated “Programming with External Hardware” section.
December 2010
1.0
Initial release.
May 2011
Altera Corporation
MAX V Device Handbook
6–10
MAX V Device Handbook
Chapter 6: JTAG and In-System Programmability in MAX V Devices
Document Revision History
May 2011
Altera Corporation
7. User Flash Memory in MAX V Devices
January 2011
MV51007-1.1
MV51007-1.1
This chapter provides guidelines for user flash memory (UFM) applications by
describing the features and functionality of the MAX® V UFM block and the
Quartus® II ALTUFM megafunction.
Altera® MAX V devices feature a UFM block that can be used for storing non-volatile
information up to 8 Kbits, similar to a serial EEPROM. The UFM provides an ideal
storage solution that supports all protocols (serial peripheral interface (SPI), parallel,
and other protocols) for interfacing through bridging logic designed into the MAX V
logic array.
This chapter contains the following sections:
■
“UFM Array Description” on page 7–1
■
“UFM Functional Description” on page 7–3
■
“UFM Operating Modes” on page 7–8
■
“Programming and Reading the UFM with JTAG” on page 7–12
■
“Software Support for UFM Block” on page 7–13
■
“Creating Memory Content File” on page 7–39
■
“Simulation Parameters” on page 7–43
UFM Array Description
Each UFM array is organized as two separate sectors with 4,096 bits per sector. Each
sector can be erased independently. Table 7–1 lists the dimensions of the UFM array.
Table 7–1. UFM Array Size
Device
Total Bits
Sectors
Address Bits
Data Width
5M40Z
8,192
2 (4,096 bits per sector)
9
16
5M80Z
8,192
2 (4,096 bits per sector)
9
16
5M160Z
8,192
2 (4,096 bits per sector)
9
16
5M240Z
8,192
2 (4,096 bits per sector)
9
16
5M570Z
8,192
2 (4,096 bits per sector)
9
16
5M1270Z
8,192
2 (4,096 bits per sector)
9
16
5M2210Z
8,192
2 (4,096 bits per sector)
9
16
© 2011 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.
and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at
www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but
reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
MAX V Device Handbook
January 2011
Subscribe
7–2
Chapter 7: User Flash Memory in MAX V Devices
UFM Array Description
Memory Organization Map
Table 7–2 lists the memory organization for the MAX V UFM block. There are 512
locations with 9 bits addressing a range of 000h to 1FFh. Each location stores 16-bit
wide data. The MSB of the address register indicates the sector in operation.
Table 7–2. Memory Organization
Sector
Address Range
1
100h
1FFh
0
000h
0FFh
Using and Accessing UFM Storage
You can use the UFM to store data of different memory sizes and data widths. Even
though the UFM storage width is 16 bits, you can implement different data widths or
a serial interface with the ALTUFM megafunction. Table 7–3 lists the different data
widths available for the three types of interfaces supported in the Quartus II software,
as well as no interface.
Table 7–3. Data Widths for Logic Array Interfaces
Logic Array Interfaces
Data Widths (Bits)
Interface Types
I2 C
8
Serial
SPI
8 or 16
Serial
Parallel
Options of 3 to 16
Parallel
None
16
Serial
For more details about the logic array interface options in the ALTUFM megafunction,
refer to “Software Support for UFM Block” on page 7–13.
1
MAX V Device Handbook
The UFM block is accessible through the logic array interface and the JTAG interface.
However, the UFM logic array interface does not have access to the configuration
flash memory (CFM) block.
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
UFM Functional Description
7–3
UFM Functional Description
Figure 7–1 is the block diagram of the MAX V UFM block and the interface signals.
Figure 7–1. UFM Block and Interface Signals
UFM Block
PROGRAM
Program
Erase
Control
ERASE
_: 4
OSC
OSC_ENA
9
RTP_BUSY
BUSY
OSC
UFM Sector 1
ARCLK
UFM Sector 0
Address
Register
16
16
ARSHFT
ARDin
DRDin
Data Register
DRDout
DRCLK
DRSHFT
Table 7–4 lists the MAX V UFM block input and output interface signals.
Table 7–4. UFM Interface Signals (Part 1 of 2)
Port Name
Port Type
Description
DRDin
Input
Serial input to the data register. It is used to enter a data word when writing to the UFM. The
data register is 16 bits wide and data is shifted serially from the LSB to the MSB with each
DRCLK. This port is required for writing, but unused if the UFM is in read-only mode.
DRCLK
Input
Clock input that controls the data register. It is required and takes control when data is
shifted from DRDin to DRDout or loaded in parallel from the flash memory. The maximum
frequency for DRCLK is 10 MHz.
DRSHFT
Input
Signal that determines whether to shift the data register or load it on a DRCLK edge. A high
value shifts the data from DRDin into the LSB of the data register and from the MSB of the
data register out to DRDout. A low value loads the value of the current address in the flash
memory to the data register.
ARDin
Input
Serial input to the address register. It is used to enter the address of a memory location to
read, program, or erase. The address register is 9 bits wide for the UFM size of 8,192 bits.
ARCLK
Input
Clock input that controls the address register. It is required when shifting the address data
from ARDin into the address register or during the increment stage. The maximum
frequency for ARCLK is 10 MHz.
Input
Signal that determines whether to shift the address register or increment it on an ARCLK
edge. A high value shifts the data from ARDin serially into the address register. A low value
increments the current address by 1. The address register rolls over to 0 when the address
space is at the maximum.
ARSHFT
January 2011
Altera Corporation
MAX V Device Handbook
7–4
Chapter 7: User Flash Memory in MAX V Devices
UFM Functional Description
Table 7–4. UFM Interface Signals (Part 2 of 2)
Port Name
Port Type
Description
PROGRAM
Input
Signal that initiates a program sequence. On the rising edge, the data in the data register is
written to the address pointed to by the address register. The BUSY signal asserts until the
program sequence is completed.
ERASE
Input
Signal that initiates an erase sequence. On a rising edge, the memory sector indicated by
the MSB of the address register is erased. The BUSY signal asserts until the erase sequence
is completed.
Input
This signal turns on the internal oscillator in the UFM block. It is required when the OSC
output is used, but optional otherwise. If OSC_ENA is driven high, the internal oscillator is
enabled and the OSC output will toggle. If OSC_ENA is driven low, the internal oscillator is
disabled and the OSC output drives constant high.
OSC_ENA
DRDout
Output
Serial output of the data register. Each time the DRCLK signal is applied, a new value is
available. The DRDout data depends on the DRSHFT signal. When the DRSHFT signal is high,
DRDout contains the new value that is shifted into the MSB of the data register. If DRSHFT is
low, DRDout contains the MSB of the memory location read into the data register.
BUSY
Output
Signal that indicates when the memory is BUSY performing a PROGRAM or ERASE
instruction. When it is high, the address and data register should not be clocked. The new
PROGRAM or ERASE instruction is not executed until the BUSY signal is deasserted.
OSC
Output
Output of the internal oscillator. It can be used to generate a clock to control user logic with
the UFM. It requires an OSC_ENA input to produce an output.
Output
This output signal is optional and only needed if the real-time ISP feature is used. The signal
is asserted high during real-time ISP and stays in the RUN_STATE for 500 ms before
initiating real-time ISP to allow for the final read/erase/write operation. No read, write,
erase, or address and data shift operations are allowed to be issued after the RTP_BUSY
signal goes high. The data and address registers do not retain the contents of the last read
or write operation for the UFM block during real-time ISP.
RTP_BUSY
f For more information about the interaction between the UFM block and the logic
array of MAX V devices, refer to the MAX V Device Architecture chapter.
MAX V Device Handbook
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
UFM Functional Description
7–5
UFM Address Register
The MAX V UFM block is organized as a 512 × 16 memory. Because the UFM block is
organized into two sectors, the MSB of the address indicates the sector that is used; 0
is for sector 0 (UFM0) while 1 is for sector 1 (UFM1). An ERASE instruction erases the
content of the specific sector that is indicated by the MSB of the address register.
Figure 7–2 shows the selection of the UFM sector using the MSB of the address
register.
For more information about the erase mode, refer to “Erase” on page 7–11.
Figure 7–2. Selection of the UFM Sector Using the MSB of the Address Register
Sector 0
Address Register
0
UFM Block
ARDin
A0
A1
LSB
A2
A3
A4
A5
A6
A7
A8
1
MSB
ARClk
UFM Block
Sector 1
Three control signals exist for the address register: ARSHFT, ARCLK, and ARDin. ARSHFT is
used as both a shift-enable control signal and an auto-increment signal. If the ARSHFT
signal is high, a rising edge on ARCLK loads address data serially from the ARDin port
and moves data serially through the register. A clock edge with the ARSHFT signal low
increments the address register by 1. This implements an auto-increment of the
address to allow data streaming. When a program, read, or erase sequence is
executing, the address that is in the address register becomes the active UFM location.
January 2011
Altera Corporation
MAX V Device Handbook
7–6
Chapter 7: User Flash Memory in MAX V Devices
UFM Functional Description
UFM Data Register
The UFM data register is 16 bits wide with four control signals: DRSHFT, DRCLK, DRDin,
and DRDout. DRSHFT distinguishes between clock edges that move data serially from
DRDin to DRDout and clock edges that latch parallel data from the UFM sectors. If the
DRSHFT signal is high, a clock edge moves data serially through the registers from
DRDin to DRDout. If the DRSHFT signal is low, a clock edge captures data from the UFM
sector pointed by the address register in parallel. The MSB is the first bit that is seen at
DRDout. The data register DRSHFT signal is also used to enable the UFM for reading
data. When the DRSHFT signal is low, the UFM latches data into the data register.
Figure 7–3 shows the UFM data register.
Figure 7–3. UFM Data Register
MAX V UFM Block
16
16
Data Register
DRDin
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
DRDout
DRCLK
MSB
LSB
UFM Program/Erase Control Block
The UFM program/erase control block is used to generate all the control signals
necessary to program and erase the UFM block independently. This block reduces the
number of logic elements (LEs) necessary to implement a UFM controller in the logic
array. It also guarantees correct timing of the control signals to the UFM. A rising edge
on either PROGRAM or ERASE signal causes this control signal block to activate and begin
sequencing through the program or erase cycle. At this point, for a program
instruction, the data currently in the data register is written to the address pointed to
by the address register.
Only sector erase is supported by the UFM. When an ERASE command is executed,
this control block erases the sector whose address is stored in the address register.
When the PROGRAM or ERASE command first activates the program/erase control
block, the BUSY signal will be driven high to indicate an operation in progress in the
UFM. After the program or erase algorithm is completed, the BUSY signal is forced
low.
MAX V Device Handbook
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
UFM Functional Description
7–7
Oscillator
OSC_ENA, one of the input signals in the UFM block, is used to enable the oscillator
signal to output through the OSC output port. You can use this OSC output port to
connect with the interface logic in the logic array. It can be routed through the logic
array and fed back as an input clock for the address register (ARCLK) and the data
register (DRCLK). The output frequency of the OSC port is one-fourth that of the
oscillator frequency. As a result, the frequency range of the OSC port is 3.9 to 5.3 MHz.
The maximum clock frequency accepted by ARCLK and DRCLK is 10 MHz and the duty
cycle accepted by the DRCLK and ARCLK input ports is approximately 45% to 50%.
When the OSC_ENA input signal is asserted, the oscillator is enabled and the output is
routed to the logic array through the OSC output. When the OSC_ENA signal is set low,
the OSC output drives constant high. The routing delay from the OSC port of the UFM
block to OSC output pin depends on placement. You can analyze this delay using the
TimeQuest timing analyzer.
The undivided internal oscillator, which is not accessible, operates in a frequency
range from 15.6 to 21.2 MHz. The internal oscillator is enabled during power-up,
in-system programming, and real-time ISP. At all other times, the oscillator is not
running unless the UFM is instantiated in the design and the OSC_ENA port is asserted.
To see how specific operating modes of the ALTUFM megafunction handle OSC_ENA
and the oscillator, refer to “Software Support for UFM Block” on page 7–13. For usergenerated logic interfacing to the UFM, the oscillator must be enabled during
program or erase operations, but not during read operations. The OSC_ENA signal can
be tied low if you are not issuing any PROGRAM or ERASE commands.
1
During real-time ISP operation, the internal oscillator automatically enables and
outputs through the OSC output port (if this port is instantiated) even though the
OSC_ENA signal is tied low. You can use the RTP_BUSY signal to detect the beginning and
ending of the real-time ISP operation for gated control of this self-enabled OSC output
condition.
1
The internal oscillator is not enabled all the time. The internal oscillator for the
program or erase operation is only activated when the flash memory block is being
programmed or erased. During a read operation, the internal oscillator is activated
whenever the flash memory block is reading data.
Instantiating the Oscillator without the UFM
You can use the MAX II/MAX V Oscillator megafunction selection in the
MegaWizard™ Plug-In Manager to instantiate the UFM oscillator if you intend to use
this signal without using the UFM memory block. Figure 7–4 shows the
ALTUFM_OSC megafunction instantiation in the Quartus II software.
Figure 7–4. The Quartus II ALTUFM_OSC Megafunction
January 2011
Altera Corporation
MAX V Device Handbook
7–8
Chapter 7: User Flash Memory in MAX V Devices
UFM Operating Modes
This megafunction is in the I/O folder on page 2a of the MegaWizard Plug-In
Manager. On page 3 of the MAX II/MAX V Oscillator megafunction, you have an
option to choose to simulate the OSC output port at its maximum or minimum
frequency during the design simulation. The frequency chosen is only used as a
timing parameter simulation and does not affect the real MAX V device OSC output
frequency.
UFM Operating Modes
There are three different modes for the UFM block:
■
Read/Stream Read
■
Program (Write)
■
Erase
During program mode, address and data can be loaded concurrently. You can
manipulate the UFM interface controls as necessary to implement the specific
protocol provided the UFM timing specifications are met. Figure 7–5 through
Figure 7–8 show the control waveforms for accessing UFM in three different modes.
For program mode (Figure 7–7) and erase mode (Figure 7–8), the PROGRAM and ERASE
signals can be asserted anytime after the address register and data register have been
loaded. Do not assert the READ, PROGRAM, and ERASE signals or shift data and address
into the UFM after entering the real-time ISP mode. You can use the RTP_BUSY signal to
detect the beginning and end of real-time ISP operation and generate control logic to
stop all UFM port operations. This user-generated control logic is only necessary for
the ALTUFM_NONE megafunction, which provides no auto-generated logic. The
other interfaces for the ALTUFM megafunction (ALTUFM_PARALLEL,
ALTUFM_SPI, ALTUFM_I2C) contain control logic to automatically monitor the
RTP_BUSY signal and will cease operations to the UFM when a real-time ISP operation
is in progress.
1
You can program the UFM or CFM block independently without overwriting the
other block, which is not programmed. The Quartus II programmer provides the
options to program the UFM and CFM blocks individually or together (the entire
MAX V Device).
f For guidelines about using ISP and real-time ISP while using the UFM block within
your design, refer to AN 100: In-System Programmability Guidelines.
f For a complete description of the device architecture, and for the specific values of the
timing parameters listed in this chapter, refer to the MAX V Device Architecture
chapter.
MAX V Device Handbook
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
UFM Operating Modes
7–9
Read/Stream Read
The three control signals, PROGRAM, ERASE, and BUSY are not required during a read or
stream read operation. To perform a read operation, the address register must be
loaded with the reference address where the data is or is going to be located in the
UFM. The address register can be stopped from incrementing or shifting addresses
from ARDin by stopping the ARCLK clock pulse. DRSHFT must be asserted low at the next
rising edge of DRCLK to load the data from the UFM to the data register. To shift the bits
from the register, 16 clock pulses must be provided to read 16-bit wide data. You can
use DRCLK to control the read time or disable the data register by discontinuing the
DRCLK clock pulse. Figure 7–5 shows the UFM control waveforms during read mode.
The UFM block can also perform a stream read operation, using the address
increment feature to read continuously from the UFM. Stream read mode is started by
loading the base address into the address register. DRSHFT must then be asserted low at
the first rising edge of DRCLK to load data into the data register from the address
pointed to by the address register. DRSHFT will then assert high to shift out the 16-bit
wide data with the MSB out first. Figure 7–6 shows the UFM control waveforms
during stream read mode.
Figure 7–5. UFM Read Waveforms
ARSHFT
tASU
tACLK
9 Address Bits tAH
ARCLK
tADH
ARDin
DRSHFT
tADS
tDSS
DRCLK
tDCLK 16 Data Bits
tDSH
tDCO
DRDin
DRDout
OSC_ENA
PROGRAM
ERASE
BUSY
Figure 7–6. UFM Stream Read Waveforms
Increment
Address
Increment
Address
ARSHFT
9 Address Bits
ARCLK
ARDin
DRSHFT
16 Data Bits
DRCLK
DRDin
DRDout
OSC_ENA
PROGRAM
ERASE
BUSY
January 2011
Altera Corporation
MAX V Device Handbook
7–10
Chapter 7: User Flash Memory in MAX V Devices
UFM Operating Modes
Program
To program or write to the UFM, you must first perform a sequence to load the
reference address into the address register. DRSHFT must then be asserted high to load
the data serially into the data register starting with the MSB. Loading an address into
the address register and loading data into the data register can be done concurrently.
After the 16 bits of data have been successfully shifted into the data register, the
PROGRAM signal must be asserted high to start writing to the UFM. On the rising edge,
the data currently in the data register is written to the location currently in the address
register. The BUSY signal is asserted until the program sequence is completed. The data
and address register should not be modified until the BUSY signal is de-asserted, or the
flash content will be corrupted. The PROGRAM signal is ignored if the BUSY signal is
asserted. When the PROGRAM signal is applied at exactly the same time as the ERASE
signal, the behavior is undefined and the flash content is corrupted. Figure 7–7 shows
the UFM waveforms during program mode.
Figure 7–7. UFM Program Waveforms
ARSHFT
tASU
ARCLK
9 Address Bits
tACLK
tAH
tADH
ARDin
DRSHFT
tADS
tDSS
16 Data Bits
tDCLK
tDSH
DRCLK
DRDin
DRDout
tDDS
tDDH
tOSCS
tOSCH
OSC_ENA
PROGRAM
ERASE
tPB
tBP
BUSY
tPPMX
MAX V Device Handbook
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
UFM Operating Modes
7–11
Erase
The ERASE signal initiates an erase sequence to erase one sector of the UFM. The data
register is not needed to perform an erase sequence. To indicate the sector of the UFM
to be erased, the MSB of the address register should be loaded with 0 to erase UFM
sector 0, or 1 to erase UFM sector 1 (Figure 7–2 on page 7–5). On a rising edge of the
ERASE signal, the memory sector indicated by the MSB of the address register will be
erased. The BUSY signal is asserted until the erase sequence is completed. The address
register should not be modified until the BUSY signal is de-asserted to prevent the flash
content from being corrupted. This ERASE signal is ignored when the BUSY signal is
asserted. Figure 7–8 illustrates the UFM waveforms during erase mode.
1
When the UFM sector is erased, it has 16-bit locations all filled with FFFF. Each UFM
storage bit can be programmed only once between erase sequences. You can write to
any word up to two times providing the second programming attempt at that location
only adds 0s. 1s are mask bits for your input word that cannot overwrite 0s in the
flash array. New 1s in the location can only be achieved by an erase. Therefore, it is
possible for you to perform byte writes because the UFM array is 16 bits for each
location.
Figure 7–8. UFM Erase Waveforms
ARSHFT
tASU
ARCLK
tACLK
9 Address Bits
tAH
tADH
ARDin
DRSHFT
tADS
DRCLK
DRDin
DRDout
OSC_ENA
PROGRAM
tOSCS
tOSCH
ERASE
BUSY
tEB
tBE
tEPMX
January 2011
Altera Corporation
MAX V Device Handbook
7–12
Chapter 7: User Flash Memory in MAX V Devices
Programming and Reading the UFM with JTAG
Programming and Reading the UFM with JTAG
In MAX V devices, you can write data to or read data from the UFM using the IEEE
Std. 1149.1 JTAG interface. You can use a PC or UNIX workstation, the Quartus II
Programmer, or the ByteBlasterMVTM or ByteBlasterTM II parallel port download
cable to download Programmer Object File (.pof), JamTM Standard Test and
Programming Language (STAPL) Files (.jam), or Jam Byte-Code Files (.jbc) from the
Quartus II software targeting the MAX V device UFM block.
1
The .pof, .jam, and .jbc files can be generated using the Quartus II software.
Jam Files
Both .jam STAPL and .jbc files support programming for the UFM block.
Jam Players
Jam Players read the descriptive information in Jam files and translate them into data
that programs the target device. Jam Players do not program a particular device
architecture or vendor; they only read and understand the syntax defined by the Jam
file specification. In-field changes are confined to the Jam file, not the Jam Player. As a
result, you do not need to modify the Jam Player source code for each in-field
upgrade.
There are two types of Jam Players to accommodate the two types of Jam files: an
ASCII Jam STAPL Player and a Jam STAPL Byte-Code Player. Both ASCII Jam STAPL
Player and Jam STAPL Byte-Code Player are coded in the C programming language
for 16-bit and 32-bit processors.
f For information about UFM operation during ISP, refer to AN 100: In-System
Programmability Guidelines.
MAX V Device Handbook
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
7–13
Software Support for UFM Block
The Altera Quartus II software includes sophisticated tools that fully utilize the
advantages of the UFM block in MAX V devices, while maintaining simple, easy-touse procedures that accelerate the design process. The following section describes
how the ALTUFM megafunction supports a simple design methodology for
instantiating standard interface protocols for the UFM block, such as:
■
I2C
■
SPI
■
Parallel
■
None (Altera Serial Interface)
This section includes the megafunction symbol, the input and output ports, and a
description of the MegaWizard Plug-In Manager options. Refer to Quartus II Help for
the ALTUFM megafunction Altera Hardware Description Language (AHDL)
functional prototypes (applicable to Verilog HDL), VHDL component declarations,
and parameter descriptions. You can access this megafunction from the Memory
Compiler directory on page 2a of the MegaWizard Plug-In Manager.
The ALTUFM MegaWizard Plug-In Manager has separate pages that apply to the
MAX V UFM block. During compilation, the Quartus II Compiler verifies the
ALTUFM parameters selected against the available logic array interface options, and
any specific assignments.
Inter-Integrated Circuit
Inter-Integrated Circuit (I2C) is a bidirectional two-wire interface protocol, requiring
only two bus lines: a serial data/address line (SDA), and a serial clock line (SCL).
Each device connected to the I2C bus is software addressable by a unique address. The
I2C bus is a multi-master bus where more than one integrated circuit (IC) capable of
initiating a data transfer can be connected to it, which allows masters to function as
transmitters or receivers.
The ALTUFM_I2C megafunction features a serial, 8-bit bidirectional data transfer up
to 100 Kbits per second. With the ALTUFM_I2C megafunction, the MAX V UFM and
logic can be configured as a slave device for the I2C bus. The ALTUFM megafunction’s
I2C interface is designed to function similar to I2C serial EEPROMs.
The Quartus II software supports four different memory sizes:
■
(128 × 8) 1 Kbits
■
(256 × 8) 2 Kbits
■
(512 × 8) 4 Kbits
■
(1,024 × 8) 8 Kbits
I2C Protocol
The following defines the characteristics of the I2C bus protocol:
■
January 2011
Only two bus lines are required: SDA and SCL. Both SDA and SCL are
bidirectional lines that remain high when the bus is free.
Altera Corporation
MAX V Device Handbook
7–14
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
■
Data transfer can be initiated only when the bus is free.
■
The data on the SDA line must be stable during the high period of the clock. The
high or low state of the data line can only change when the clock signal on the SCL
line is low.
■
Any transition on the SDA line while the SCL is high indicates a start or stop
condition.
Table 7–5 lists the ALTUFM_I2C megafunction input and output interface signals.
Table 7–5. ALTUFM_I2C Interface Signals
Pin
Description
Function
SDA
Serial Data/Address Line
The bidirectional SDA port is used to transmit and receive serial data from the
UFM. The output stage of the SDA port is configured as an open drain pin to
perform the wired-AND function.
SCL
Serial Clock Line
The bidirectional SCL port is used to synchronize the serial data transfer to and
from the UFM. The output stage of the SCL port is configured as an open drain
pin to perform a wired-AND function.
WP
Write Protect
Optional active high signal that disables the erase and write function for
read/write mode. The ALTUFM_I2C megafunction gives you an option to
protect the entire UFM memory or only the upper half of memory.
A2, A1, A0
Slave Address Input
These inputs set the UFM slave address. The A6, A5, A4, A 3 slave address bits
are programmable, set internally to 1010 by default.
START and STOP Condition
The master always generates start (S) and stop (P) conditions. After the start
condition, the bus is considered busy. Only a stop (P) condition frees the bus. The bus
stays busy if the repeated start (Sr) condition is executed instead of a stop condition.
In this occurrence, the start (S) and repeated start (Sr) conditions are functionally
identical.
A high-to-low transition on the SDA line while the SCL is high indicates a start
condition. A low-to-high transition on the SDA line while the SCL is high indicates a
stop condition. Figure 7–9 shows the start and stop conditions.
Figure 7–9. Start and Stop Conditions
SDA
SDA
SCL
SCL
S
Start Condition
MAX V Device Handbook
P
Stop Condition
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
7–15
Acknowledge
Acknowledged data transfer is a requirement of I2C. The master must generate a clock
pulse to signify the acknowledge bit. The transmitter releases the SDA line (high)
during the acknowledge clock pulse.
The receiver (slave) must pull the SDA line low during the acknowledge clock pulse
so that SDA remains a stable low during the clock high period, indicating positive
acknowledgement from the receiver. If the receiver pulls the SDA line high during the
acknowledge clock pulse, the receiver sends a not-acknowledge condition indicating
that it is unable to process the last byte of data. If the receiver is busy (for example,
executing an internally-timed erase or write operation), it will not acknowledge any
new data transfer. Figure 7–10 shows the acknowledge condition on the I2C bus.
Figure 7–10. Acknowledge on the I2C Bus
Data Output
By Transmitter
Not Acknowledge
Data Output
By Receiver
Acknowledge
SCL From
Master
S
Start Condition
Clock Pulse For
Acknowledgement
Device Addressing
After the start condition, the master sends the address of the particular slave device it
is requesting. The four most significant bits (MSBs) of the 8-bit slave address are
usually fixed while the next three significant bits (A2, A1, A0) are device address bits
that define which device the master is accessing. The last bit of the slave address
specifies whether a read or write operation is to be performed. When this bit is set to
1, a read operation is selected. When this bit is set to 0, a write operation is selected.
The four MSBs of the slave address (A6, A5, A4, A3) are programmable and can be
defined on page 3 of the ALTUFM MegaWizard Plug-In Manager. The default value
for these four MSBs is 1010. The next three significant bits are defined using the three
A2, A1, A0 input ports of the ALTUFM_I2C megafunction. You can connect these ports
to input pins in the design file and connect them to switches on the board. The other
option is to connect them to V CC and GND primitives in the design file, which
conserves pins. Figure 7–11 shows the slave address bits.
January 2011
Altera Corporation
MAX V Device Handbook
7–16
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
Figure 7–11. Slave Address Bits
MSB
1- or 2-Kbit Memory Size
1
LSB
0
1
0
A2
A1
MSB
4-Kbit Memory Size (1)
1
LSB
0
1
0
A2
A1
MSB
8-Kbit Memory Size (2)
1
A0 R/W
a8 R/W
LSB
0
1
0
A2
a9
a8 R/W
Notes to Figure 7–11:
(1) For the 4-Kbit memory size, the A0 location in the slave address becomes the MSB (a8) of the memory byte
address.
(2) For the 8-Kbit memory size, the A0 location in the slave address becomes a8 of the memory byte address, while
the A1 location in the slave address becomes the MSB (a9) of the memory byte address.
After the master sends a start condition and the slave address byte, the ALTUFM_I2C
logic monitors the bus and responds with an acknowledge (on the SDA line) when its
address matches the transmitted slave address. The ALTUFM_I2C megafunction then
performs a read or write operation to or from the UFM, depending on the state of the
bit.
Byte Write Operation
The master initiates a transfer by generating a start condition, then sending the correct
slave address (with the R/W bit set to 0) to the slave. If the slave address matches, the
ALTUFM_I2C slave acknowledges on the ninth clock pulse. The master then transfers
an 8-bit byte address to the UFM, which acknowledges the reception of the address.
The master transfers the 8-bit data to be written to the UFM. After the ALTUFM_I2C
logic acknowledges the reception of the 8-bit data, the master generates a stop
condition. The internal write from the MAX V logic array to the UFM begins only
after the master generates a stop condition. While the UFM internal write cycle is in
progress, the ALTUFM_I2C logic ignores any attempt made by the master to initiate a
new transfer. Figure 7–12 shows the byte write sequence.
Figure 7–12. Byte Write Sequence
S
S – Start Condition
P – Stop Condition
A – Acknowledge
MAX V Device Handbook
Slave Address
R/W
"0" (write)
A
Byte Address
A
Data
A
P
From Master to Slave
From Slave to Master
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
7–17
Page Write Operation
Page write operation has a similar sequence as the byte write operation, except that
several bytes of data are transmitted in sequence before the master issues a stop
condition. The internal write from the MAX V logic array to the UFM begins only
after the master generates a stop condition. While the UFM internal write cycle is in
progress, the ALTUFM_I2C logic ignores any attempt made by the master to initiate a
new transfer. The ALTUFM_I2C megafunction allows you to choose the page size of 8
bytes, 16 bytes, or 32 bytes for the page write operation.
A write operation is only possible to an erased UFM block or word location. The UFM
block differs from serial EEPROMs, requiring an erase operation before writing new
data in the UFM block. A special erase sequence is required, as discussed in “Erase
Operation”.
Acknowledge Polling
The master can detect whether the internal write cycle is completed by polling for an
acknowledgement from the slave. The master can re-send the start condition together
with the slave address as soon as the byte write sequence is finished. The slave does
not acknowledge if the internal write cycle is still in progress. The master can repeat
the acknowledge polling and proceed with the next instruction after the slave
acknowledges.
Write Protection
The ALTUFM_I2C megafunction includes an optional Write Protection (WP) port
available on page 4 of the ALTUFM MegaWizard Plug-In Manager. In the
MegaWizard Plug-In Manager, you can choose the WP port to protect either the full or
upper half memory.
When WP is set to 1, the upper half or the entire memory array (depending on the
write protection level selected) is protected, and the write and erase operations are not
allowed. The ALTUFM_I2C megafunction acknowledges the slave address and
memory address. After the master transfers the first data byte, the ALTUFM_I2C
megafunction sends a not-acknowledge condition to the master to indicate that the
instruction will not execute. When WP is set to 0, the write and erase operations are
allowed.
Erase Operation
Commercial serial EEPROMs automatically erase each byte of memory before writing
into that particular memory location during a write operation. However, the MAX V
UFM block is flash based and only supports sector erase operations. Byte erase
operations are not supported. When using read/write mode, a sector or full memory
erase operation is required before writing new data into any location that previously
contained data. The block cannot be erased when the ALTUFM_I2C megafunction is
in read-only mode.
Data can be initialized into memory for read/write and read-only modes by including
a memory initialization file (.mif) or hexadecimal file (.hex) in the ALTUFM
MegaWizard Plug-In Manager. This data is automatically written into the UFM
during device programming by the Quartus II software or third-party programming
tool.
January 2011
Altera Corporation
MAX V Device Handbook
7–18
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
The ALTUFM_I2C megafunction supports four different erase operation methods
shown on page 4 of the ALTUFM MegaWizard Plug-In Manager:
■
Full Erase (Device Slave Address Triggered)
■
Sector Erase (Byte Address Triggered)
■
Sector Erase (A2 Triggered)
■
No Erase
These erase options only work as described if that particular option is selected in the
MegaWizard Plug-In Manager before compiling the design files and programming
the device. Only one option can be selected for the ALTUFM_I2C megafunction.
Each erase option is discussed in more detail in the following sections.
Full Erase (Device Slave Address Triggered)
The full erase option uses the A2, A1, A0 bits of the slave address to distinguish
between an erase or read/write operation. This slave operation decoding occurs when
the master transfers the slave address to the slave after generating the start condition.
If the A2, A1, and A0 slave address bits transmitted to the UFM slave equals 111 and
the four remaining MSBs match the rest of the slave addresses, then the Full Erase
operation is selected. If the A6, A5, A4, A3 A2, A1, and A0 slave address bits transmitted
to the UFM match its unique slave address setting, the read/write operation is
selected and functions as expected. As a result, this erase option utilizes two slave
addresses on the bus reserving A6, A5, A4, A3, 1, 1, 1 as the erase trigger. Both sectors
of the UFM block will be erased when the Full Erase operation is executed. This
operation requires acknowledge polling. The internal UFM erase function only begins
after the master generates a stop condition. Figure 7–13 shows the full erase sequence
triggered by using the slave address.
If the memory is write-protected (WP = 1), the slave does not acknowledge the erase
trigger slave address (A6, A5, A4, A3, 1, 1, 1) sent by the master. The master should
then send a stop condition to terminate the transfer. The full erase operation will not
be executed.
Figure 7–13. Full Erase Sequence Triggered Using the Slave Address
S
Slave Address
A6A5A4A3111
S – Start Condition
P – Stop Condition
A – Acknowledge
MAX V Device Handbook
R/W
'0' (write)
A
P
From Master to Slave
From Slave to Master
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
7–19
Sector Erase (Byte Address Triggered)
This sector erase operation is triggered by defining a 7- to 10-bit byte address for each
sector depending on the memory size. The trigger address for each sector is entered
on page 4 of the ALTUFM MegaWizard Plug-In Manager. When a write operation is
executed targeting this special byte address location, the UFM sector that contains
that byte address location is erased. This sector erase operation is automatically
followed by a write of the intended write byte to that address. The default byte
address location for UFM Sector 0 erase is address 0×00. The default byte address
location for UFM Sector 1 erase is [(selected memory size)/2]. You can specify another
byte location as the trigger-erase addresses for each sector.
This sector erase operation supports up to eight UFM blocks or serial EEPROMs on
the I2C bus. This sector erase operation requires acknowledge polling.
Sector Erase (A2 Triggered)
This sector erase operation uses the received A2 slave address bit to distinguish
between an erase or read/write operation. This slave operation decoding occurs when
the master transmits the slave address after generating the start condition. If the A2 bit
received by the UFM slave is 1, the sector erase operation is selected. If the A2 bit
received is 0, the read/write operation is selected. While this reserves the A2 bit as an
erase or read/write operation bit, the A0 and A1 bits still act as slave address bits to
address the UFM. With this erase option, there can be up to four UFM slaves cascaded
on the bus for 1-Kbit and 2-Kbit memory sizes. Only two UFM slaves can be cascaded
on the bus for 4-Kbit memory size, because A0 of the slave address becomes the ninth
bit (MSB) of the byte address. After the slave acknowledges the slave address and its
erase or read/write operation bit, the master can transfer any byte address within the
sector that must be erased. The internal UFM sector erase operation only begins after
the master generates a stop condition. Figure 7–14 shows the sector erase sequence
using the A2 bit of the slave address.
Figure 7–14. Sector Erase Sequence Indicated Using the A2 Bit of the Slave Address
S
Slave Address
R/W
A2 = '1'
S – Start Condition
P – Stop Condition
A – Acknowledge
A
'0' (write) (1)
Byte Address
A
P
From Master to Slave
From Slave to Master
Note to Figure 7–14:
(1) A2 = 0 indicates a read/write operation is executed in place of an erase. Here, the R/W bit determines whether it is
a read or write operation.
If the ALTUFM_I2C megafunction is write-protected (WP=1), the slave does not
acknowledge the byte address (that indicates the UFM sector to be erased) sent in by
the master. The master should then send a stop condition to terminate the transfer and
the sector erase operation will not be executed.
January 2011
Altera Corporation
MAX V Device Handbook
7–20
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
No Erase
The no erase operation never erases the UFM contents. This method is recommended
when UFM does not require constant re-writing after its initial write of data. For
example, if the UFM data is to be initialized with data during manufacturing using
I2C, you may not require writing to the UFM again. In that case, you should use the no
erase option and save LE resources from being used to create erase logic.
Read Operation
The read operation is initiated in the same manner as the write operation except that
the R/W bit must be set to 1. Three different read operations are supported:
■
Current Address Read (Single Byte)
■
Random Address Read (Single byte)
■
Sequential Read (Multi-Byte)
After each UFM data has been read and transferred to the master, the UFM address
register is incremented for all single and multi-byte read operations.
Current Address Read
This read operation targets the current byte location pointed to by the UFM address
register. Figure 7–15 shows the current address read sequence.
Figure 7–15. Current Address Read Sequence
S
Slave Address
R/W
A
Data
P
‘1’ (read)
S – Start Condition
P – Stop Condition
A – Acknowledge
MAX V Device Handbook
From Master to Slave
From Slave to Master
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
7–21
Random Address Read
Random address read operation allows the master to select any byte location for a
read operation. The master first performs a “dummy” write operation by sending the
start condition, slave address, and byte address of the location it wishes to read. After
the ALTUFM_I2C megafunction acknowledges the slave and byte address, the master
generates a repeated start condition, the slave address, and the R/W bit is set to 1. The
ALTUFM_I2C megafunction then responds with acknowledge and sends the 8-bit
data requested. The master then generates a stop condition. Figure 7–16 shows the
random address read sequence.
Figure 7–16. Random Address Read Sequence
S
Slave
Address
R/W
Byte
Address
A
A
Sr
Slave
Address
R/W
Data
A
P
‘1’ (read)
‘0’ (write)
From Master to Slave
S – Start Condition
Sr – Repeated Start
P – Stop Condition
A – Acknowledge
From Slave to Master
Sequential Read
Sequential read operation can be initiated by either the current address read operation
or the random address read operation. Instead of sending a stop condition after the
slave has transmitted one byte of data to the master, the master acknowledges that
byte and sends additional clock pulses (on the SCL line) for the slave to transmit data
bytes from consecutive byte addresses. The operation is terminated when the master
generates a stop condition instead of responding with an acknowledge. Figure 7–17
shows the sequential read sequence.
Figure 7–17. Sequential Read Sequence
S
Slave
Address
R/W
‘0’ (write)
S – Start Condition
Sr – Repeated Start
P – Stop Condition
A – Acknowledge
January 2011
Altera Corporation
A
Byte
Address
A
Sr
Slave
Address
R/W
‘1’ (read)
A
Data
A
…
Data
P
Data (n - bytes) + Acknowledgment (n - 1 bytes)
From Master to Slave
From Slave to Master
MAX V Device Handbook
7–22
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
ALTUFM_I2C Interface Timing Specification
Figure 7–18 shows the timing waveform for the ALTUFM_I2C megafunction
read/write mode.
Figure 7–18. Timing Waveform for the ALTUFM_I2C Megafunction
SDA
tSU:STA
tHD:DAT
tHD:STA
tSU:DAT
tSU:STO
tBUF
tSCLSDA
tHIGH
SCL
tLOW
Table 7–6 through Table 7–8 list the timing specification needed for the ALTUFM_I2C
megafunction read/write mode.
Table 7–6. I2C Interface Timing Specification
Symbol
Parameter
Min
Max
Unit
FSCL
SCL clock frequency
—
100
kHz
tSCL:SDA
SCL going low to SDA data out
—
15
ns
tBUF
Bus free time between a stop and start condition
4.7
—
µs
tHD:STA
(Repeated) start condition hold time
4
—
µs
tSU:STA
(Repeated) start condition setup time
4.7
—
µs
tLOW
SCL clock low period
4.7
—
µs
tHIGH
SCL clock high period
4
—
µs
tHD:DAT
SDA data in hold time
0
—
ns
tSU:DAT
SDA data in setup time
20
—
ns
tSU:STO
STOP condition setup time
4
—
ns
Table 7–7. UFM Write Cycle Time
Parameter
Min
Max
Unit
Write Cycle Time
—
110
µs
Min
Max
Unit
Sector Erase
Cycle Time
—
501
ms
Full Erase Cycle
Time
—
1,002
ms
Table 7–8. UFM Erase Cycle Time
Parameter
MAX V Device Handbook
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
7–23
Instantiating the I2C Interface Using the Quartus II ALTUFM_I2C
Megafunction
Figure 7–19 shows the ALTUFM_I2C megafunction symbol for a I2C interface
instantiation in the Quartus II software.
Figure 7–19. ALTUFM_I2C Megafunction Symbol for the I 2C Interface Instantiation in the Quartus
II Software
ALTUFM_I2C megafunction is under the Memory Compiler folder on page 2a of the
MegaWizard Plug-In Manager. On page 3, you can choose whether to implement the
Read/Write or Read Only mode for the UFM. You also have an option to choose the
memory size for the ALTUFM_I2C megafunction as well as defining the four MSBs of
the slave address (default 1010).
You can select the optional write protection and erase operation methods on page 4 of
the ALTUFM MegaWizard Plug-In Manager.
1
The UFM block’s internal oscillator is always running when the ALTUFM_I2C
megafunction is instantiated for both read-only and read/write interfaces.
Serial Peripheral Interface
Serial peripheral interface (SPI) is a four-pin serial communication subsystem
included on the Motorola 6805 and 68HC11 series microcontrollers. It allows the
microcontroller unit to communicate with peripheral devices, and is also capable of
inter-processor communications in a multiple-master system.
The SPI bus consists of masters and slaves. The master device initiates and controls
the data transfers and provides the clock signal for synchronization. The slave device
responds to the data transfer request from the master device. The master device in an
SPI bus initiates a service request with the slave devices responding to the service
request.
With the ALTUFM megafunction, the UFM and MAX V logic can be configured as a
slave device for the SPI bus. The OSC_ENA is always asserted to enable the internal
oscillator when the SPI megafunction is instantiated for both read only and
read/write interfaces.
January 2011
Altera Corporation
MAX V Device Handbook
7–24
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
The Quartus II software supports both the Base mode (uses 8-bit address and data)
and the Extended mode (uses 16-bit address and data). Base mode uses only UFM
sector 0 (2,048 bits), while Extended mode uses both UFM sector 0 and sector 1 (8,192
bits). There are only four pins in SPI: SI, SO, SCK, and nCS. Table 7–9 describes the SPI
pins and functions.
Table 7–9. SPI Interface Signals
Pin
Description
Function
SI
Serial Data Input
Receive data serially.
SO
Serial Data Output
Transmit data serially.
SCK
Serial Data Clock
The clock signal produced from the master device to
synchronize the data transfer.
nCS
Chip Select
Active low signal that enables the slave device to
receive or transfer data from the master device.
Data transmitted to the SI port of the slave device is sampled by the slave device at
the positive SCK clock. Data transmits from the slave device through SO at the negative
SCK clock edge. When nCS is asserted, it means the current device is being selected by
the master device from the other end of the SPI bus for service. When nCS is not
asserted, the SI and SCK ports should be blocked from receiving signals from the
master device, and SO should be in High Impedance state to avoid causing contention
on the shared SPI bus. All instructions, addresses, and data are transferred with the
MSB first and start with high-to-low nCS transition. The circuit diagram is shown in
Figure 7–20.
Figure 7–20. Circuit Diagram for SPI Interface Read or Write Operations
SI SO SCK nCS
Op-Code Decoder
Read, Write, and Erase
State Machine
SPI Interface
Control Logic
UFM Block
Address and Data Hub
Eight-Bit Status Shift Register
MAX V Device Handbook
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
7–25
Opcodes
Table 7–10 lists the 8-bit instruction opcodes. After nCS is pulled low, the indicated
opcode must be provided. Otherwise, the interface assumes that the master device
has internal logic errors and ignores the rest of the incoming signals. When nCS is
pulled back to high, the interface is back to normal. nCS should be pulled low again
for a new service request.
Table 7–10. Instruction Set for SPI
Name
Opcode
Operation
WREN
00000110
Enable Write to UFM
WRDI
00000100
Disable Write to UFM
RDSR
00000101
Read Status Register
WRSR
00000001
Write Status Register
READ
00000011
Read data from UFM
WRITE
00000010
Write data to UFM
SECTOR-ERASE
00100000
Sector erase
UFM-ERASE
01100000
Erase the entire UFM block (both sectors)
The READ and WRITE opcodes are instructions for transmission, which means the data
will be read from or written to the UFM.
WREN, WRDI, RDSR, and WRSR are instructions for the status register, where they do not
have any direct interaction with UFM, but read or set the status register within the
interface logic. The status register provides status on whether the UFM block is
available for any READ or WRITE operation, whether the interface is WRITE enabled, and
the state of the UFM WRITE protection. Table 7–11 lists the status register format. For
the read only implementation of ALTUFM SPI (Base or Extended mode), the status
register does not exist, saving LE resources.
Table 7–11. Status Register Format
Position
Status
Default at Power-Up
Description
Bit 7
X
0
—
Bit 6
X
0
—
Bit 5
X
0
—
Bit 4
X
0
—
Bit 3
BP1
0
Indicate the current level of block write protection (1)
Bit 2
BP0
0
Indicate the current level of block write protection (1)
Bit 1
WEN
0
Bit 0
nRDY
0
1= SPI WRITE enabled state
0= SPI WRITE disabled state
1 = Busy, UFM WRITE or ERASE cycle in progress
0 = No UFM WRITE or ERASE cycle in progress
Note to Table 7–11:
(1) For more information about status register bits BP1 and BP0, refer to Table 7–12 and Table 7–13 on page 7–34.
The following sections describe the instructions for SPI.
January 2011
Altera Corporation
MAX V Device Handbook
7–26
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
READ
READ is the instruction for data transmission, where the data is read from the UFM
block. When data transfer is taking place, the MSB is always the first bit to be
transmitted or received. The data output stream is continuous through all addresses
until it is terminated by a low-to-high transition at the nCS port. The READ operation is
always performed through the following sequence in SPI, as shown in Figure 7–21:
1. nCS is pulled low to indicate the start of transmission.
2. An 8-bit READ opcode (00000011) is received from the master device. (If internal
programming is in progress, READ is ignored and not accepted).
3. A 16-bit address is received from the master device. The LSB of the address is
received last. Because the UFM block can take only nine bits of address maximum,
the first seven address bits received are discarded.
4. Data is transmitted for as many words as needed by the slave device through SO
for READ operation. When the end of the UFM storage array is reached, the address
counter rolls over to the start of the UFM to continue the READ operation.
5. nCS is pulled back to high to indicate the end of transmission.
For SPI Base mode, the READ operation is always performed through the following
sequence in SPI:
1. nCS is pulled low to indicate the start of transmission.
2. An 8-bit READ opcode (00000011) is received from the master device, followed by
an 8-bit address. If internal programming is in progress, the READ operation is
ignored and not accepted.
3. Data is transmitted for as many words as needed by the slave device through SO
for READ operation. The internal address pointer automatically increments until the
highest memory address is reached (address 255 only because the UFM sector 0 is
used). The address counter will not roll over when address 255 is reached. The SO
output is set to high-impedance (Z) when all eight data bits from address 255 have
been shifted out through the SO port.
4. nCS is pulled back to high to indicate the end of transmission.
Figure 7–21. READ Operation Sequence for Extended Mode
nCS
0
1
2
3
4
5 6 7
8
9 10 11
20 21 22 23 24 25 26 27
36 37 38 39
SCK
8-bit
Instruction
SI
03H
MSB
SO
16-bit
Address
MSB
High Impedance
16-bit Data Out 1
MSB
MAX V Device Handbook
16-bit Data Out 2
MSB
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
7–27
Figure 7–22 shows the READ operation sequence for Base mode.
Figure 7–22. READ Operation for Base Mode
nCS
1
2
3
4
5
6
7 8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 23
SCK
8-bit
Instruction
8-bit
Address
03H
SI
MSB
MSB
High Impedance
SO
8-bit Data Out 1
MSB
8-bit Data Out 2
MSB
WRITE
WRITE is the instruction for data transmission, where the data is written to the UFM
block. The targeted location in the UFM block that will be written must be in the
erased state (FFFFH) before initiating a WRITE operation. When data transfer is taking
place, the MSB is always the first bit to be transmitted or received. nCS must be driven
high before the instruction is executed internally. You may poll the nRDY bit in the
software status register for the completion of the internal self-timed WRITE cycle. For
SPI Extended mode, the WRITE operation is always done through the following
sequence, as shown in Figure 7–23:
1. nCS is pulled low to indicate the start of transmission.
2. An 8-bit WRITE opcode (00000010) is received from the master device. If internal
programming is in progress, the WRITE operation is ignored and not accepted.
3. A 16-bit address is received from the master device. The LSB of the address will be
received last. Because the UFM block can take only nine bits of address maximum,
the first seven address bits received are discarded.
4. A check is carried out on the status register (see Table 7–11) to determine if the
WRITE operation has been enabled, and the address is outside of the protected
region; otherwise, Step 5 is bypassed.
5. One word (16 bits) of data is transmitted to the slave device through SI.
6. nCS is pulled back to high to indicate the end of transmission.
For SPI Base mode, the WRITE operation is always performed through the following
sequence in SPI:
1. nCS is pulled low to indicate the start of transmission.
2. An 8-bit WRITE opcode (00000010) is received. If the internal programming is in
progress, the WRITE operation is ignored and not accepted.
3. An 8-bit address is received. A check is carried out on the status register (see
Table 7–11) to determine if the WRITE operation has been enabled, and the address
is outside of the protected region; otherwise, Step 4 is skipped.
January 2011
Altera Corporation
MAX V Device Handbook
7–28
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
4. An 8-bit data is transmitted through SI.
5. nCS is pulled back to high to indicate the end of transmission.
Figure 7–23. WRITE Operation Sequence for Extended Mode
nCS
0
1
2
3
4
5 6 7
8
9 10 11
20 21 22 23 24 25 26 27
36 37 38 39
SCK
8-bit
Instruction
SI
16-bit
Address
16-bit Data In
02H
MSB
MSB
MSB
High Impedance
SO
Figure 7–24 shows the WRITE operation sequence for Base mode.
Figure 7–24. WRITE Operation Sequence for Base Mode
nCS
0
1
2
3
4
5 6 7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
SCK
8-bit
Instruction
SI
8-bit
Address
02H
8-bit Data In
MSB
SO
MSB
High Impedance
SECTOR-ERASE
SECTOR-ERASE (SE) is the instruction of erasing one sector of the UFM block. Each
sector contains 256 words. WEN bit and the sector must not be protected for SE
operation to be successful. nCS must be driven high before the instruction is executed
internally. You may poll the nRDY bit in the software status register for the completion
of the internal self-timed SECTOR-ERASE cycle. For SPI Extended mode, the SE
operation is performed in the following sequence, as shown in Figure 7–25:
1. nCS is pulled low.
2. Opcode 00100000 is transmitted into the interface.
3. The 16-bit address is sent. The eighth bit (the first seven bits will be discarded) of
the address indicates which sector is erased; a 0 means sector 0 (UFM0) is erased,
and a 1 means sector 1 (UFM1) is erased.
MAX V Device Handbook
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
7–29
4. nCS is pulled back to high.
For SPI Base mode, the SE instruction erases UFM sector 0. Because there are no
choices of UFM sectors to be erased, there is no address component to this instruction.
The SE operation is always done through the following sequence in SPI Base mode:
1. nCS is pulled low.
2. Opcode 00100000 is transmitted into the interface.
3. nCS is pulled back to high.
Figure 7–25. SECTOR-ERASE Operation Sequence for Extended Mode
nCS
0
1
2
3
4
5 6 7
8
9 10 11
20 21 22 23
SCK
8-bit
Instruction
16-bit
Address
20H
SI
MSB
MSB
High Impedance
SO
Figure 7–26 shows the SECTOR-ERASE operation sequence for Base mode.
Figure 7–26. SECTOR_ERASE Operation Sequence for Base Mode
nCS
0
1
2
3
4
5 6 7
SCK
8-bit
Instruction
SI
20H
MSB
High Impedance
SO
January 2011
Altera Corporation
MAX V Device Handbook
7–30
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
UFM-ERASE
The UFM-ERASE (CE) instruction erases both UFM sector 0 and sector 1 for SPI
Extended Mode. While for SPI Base mode, the CE instruction has the same
functionality as the SECTOR-ERASE (SE) instruction, which erases UFM sector 0 only.
WEN bit and the UFM sectors must not be protected for CE operation to be successful.
nCS must be driven high before the instruction is executed internally. You may poll the
nRDY bit in the software status register for the completion of the internal self-timed CE
cycle. For both SPI Extended mode and Base mode, the CE operation is performed in
the following sequence as shown in Figure 7–27:
1. nCS is pulled low.
2. Opcode 01100000 is transmitted into the interface.
3. nCS is pulled back to high.
Figure 7–27 shows the UFM-ERASE operation sequence.
Figure 7–27. UFM-ERASE Operation Sequence
nCS
0
1
2
3
4
5 6 7
SCK
8-bit
Instruction
SI
60H
MSB
High Impedance
SO
MAX V Device Handbook
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
7–31
WREN (Write Enable)
The interface is powered-up in the write disable state. Therefore, WEN in the status
register (refer to Table 7–11) is 0 at power-up. Before any write is allowed to take
place, WREN must be issued to set WEN in the status register to 1. If the interface is in
read-only mode, WREN does not have any effect on WEN, because the status register does
not exist. After WEN is set to 1, it can be reset by the WRDI instruction; the WRITE and
SECTOR-ERASE instructions will not reset the WEN bit. WREN is issued through the
following sequence, as shown in Figure 7–28:
1. nCS is pulled low.
2. Opcode 00000110 is transmitted into the interface to set WEN to 1 in the status
register.
3. After the transmission of the eighth bit of WREN, the interface is in wait state
(waiting for nCS to be pulled back to high). Any transmission after this is ignored.
4. nCS is pulled back to high.
Figure 7–28. WREN Operation Sequence
nCS
0
1
2
3
4
5 6 7
SCK
8-bit
Instruction
06H
SI
MSB
SO
January 2011
Altera Corporation
High Impedance
MAX V Device Handbook
7–32
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
WRDI (Write Disable)
After the UFM is programmed, WRDI can be issued to set WEN back to 0, disabling WRITE
and preventing inadvertent writing to the UFM. WRDI is issued through the following
sequence, as shown in Figure 7–29:
1. nCS is pulled low.
2. Opcode 00000100 is transmitted to set WEN to 0 in the status register.
3. After the transmission of the eighth bit of WRDI, the interface is in wait state
(waiting for nCS to be pulled back to high). Any transmission after this is ignored.
4. nCS is pulled back to high.
Figure 7–29. WRDI Operation Sequence
nCS
0
1
2
3
4
5 6 7
SCK
8-bit
Instruction
04H
SI
MSB
SO
MAX V Device Handbook
High Impedance
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
7–33
RDSR (Read Status Register)
The content of the status register can be read by issuing RDSR. After RDSR is received,
the interface outputs the content of the status register through the SO port. Although
the four most significant bits (Bit 7 to Bit 4) do not hold valuable information, all eight
bits in the status register will output through the SO port. This allows future
compatibility when Bit 7 to Bit 4 have new meaning in the status register. During the
internal program cycle in the UFM, RDSR is the only valid opcode recognized by the
interface (therefore, the status register can be read at any time), and nRDY is the only
valid status bit. Other status bits are frozen and remain unchanged until the internal
program cycle is ended. RDSR is issued through the following sequence, as shown in
Figure 7–30:
1. nCS is pulled low.
2. Opcode 00000101 is transmitted into the interface.
3. SI ignores incoming signals; SO outputs the content of the status register, Bit 7 first
and Bit 0 last.
4. If nCS is kept low, repeat step 3.
5. nCS is pulled back to high to terminate the transmission.
Figure 7–30. RDSR Operation Sequence
nCS
0
1
2
3
4
5 6 7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
SCK
8-bit
Instruction
SI
05H
MSB
SO
High Impedance
MSB
Status Register Out
MSB
January 2011
Altera Corporation
MSB
MAX V Device Handbook
7–34
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
WRSR (Write Status Register)
The block protection bits(BP1 and BP0) are the status bits used to protect certain
sections of the UFM from inadvertent write. The BP1 and BP0 status are updated by
WRSR. During WRSR, only BP1 and BP0 in the status register can be written with valid
information. The rest of the bits in the status register are ignored and not updated.
When both BP1 and BP0 are 0, there is no protection for the UFM. When both BP1 and
BP0 are 1, there is full protection for the UFM. BP0 and BP1 are set to 0 upon power-up.
Table 7–12 lists the Block Write Protect Bits for Extended mode, while Table 7–13 lists
the Block Write Protect Bits for Base mode. WRSR is issued through the following
sequence, as shown in Figure 7–31:
1. nCS is pulled low.
2. Opcode 00000001 is transmitted into the interface.
3. An 8-bit status is transmitted into the interface to update BP1 and BP0 of the status
register.
4. If nCS is pulled high too early (before all the eight bits in Step 2 or Step 3 are
transmitted) or too late (the ninth bit or more is transmitted), WRSR is not executed.
5. nCS is pulled back to high to terminate the transmission.
Figure 7–31. WRSR Operation Sequence
nCS
0
1
2
3
4
5 6 7
8
9 10 11 12 13 14 15
SCK
8-bit
Instruction
SI
01H
MSB
Status Register In
MSB
High Impedance
SO
Table 7–12. Block Write Protect Bits for Extended Mode
Status Register Bits
BP1
BP0
UFM Array Address
Protected
0 (No protection)
0
0
None
3 (Full protection)
1
1
000 to 1FF
Level
Table 7–13. Block Write Protect Bits for Base Mode
Status Register Bits
Level
MAX V Device Handbook
UFM Array Address
Protected
BP1
BP0
0 (No protection)
0
0
None
3 (Full protection)
1
1
000 to 0FF
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
7–35
ALTUFM SPI Timing Specification
Figure 7–32 shows the timing specification needed for the SPI Extended mode
(read/write). These nCS timing specifications do not apply to the SPI Extended
read-only mode nor to any of the SPI Base modes. However, for the SPI Extended
mode (read only) and the SPI Base mode (both read only and read/write), the nCS
signal and SCK are not allowed to toggle at the same time. Table 7–14 lists the timing
parameters that only apply to the SPI Extended mode (read/write).
Figure 7–32. SPI Timing Waveform
tHNCSHIGH
nCS
tSCK2NCS
tNCS2SCK
SCK
Table 7–14. SPI Timing Parameters for Extended Mode
Symbol
Description
Minimum (ns)
Maximum (ns)
tSCK2NCS
The time required for the SCK signal falling edge to nCS signal rising edge
50
—
tHNCSHIGH
The time that the nCS signal must be held high
600
—
tNCS2SCK
The time required for the nCS signal falling edge to SCK signal rising edge
750
—
Instantiating SPI Using Quartus II ALTUFM_SPI Megafunction
Figure 7–33 shows the ALTUFM_SPI megafunction symbol for SPI instantiation in the
Quartus II software.
Figure 7–33. ALTUFM_SPI Megafunction Symbol for SPI Instantiation
ALTUFM_SPI megafunction is under the Memory Compiler folder on page 2a of the
MegaWizard Plug-In Manager. On page 3, you can choose whether to implement the
Read/Write or Read Only mode as the access mode for the UFM. You can also select
the configuration mode (Base or Extended) for SPI on this page. You can specify the
initial content of the UFM block on page of the ALTUFM MegaWizard Plug-In
Manager as discussed in “Creating Memory Content File” on page 7–39.
1
January 2011
The UFM block’s internal oscillator is always running when the ALTUFM_SPI
megafunction is instantiated for read/write interface. The UFM block’s internal
oscillator is disabled when the ALTUFM_SPI megafunction is instantiated for read
only interface.
Altera Corporation
MAX V Device Handbook
7–36
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
Parallel Interface
This interface allows for parallel communication between the UFM block and outside
logic. After the READ request, WRITE request, or ERASE request is asserted (active low
assertion), the outside logic or device (such as a microcontroller) can continue its
operation while the data in the UFM is retrieved, written, or erased. During this time,
the nBUSY signal is driven “low” to indicate that it is not available to respond to any
further request. After the operation is complete, the nBUSY signal is brought back to
“high” to indicate that it is now available to service a new request. If it was the Read
request, the DATA_VALID is driven “high” to indicate that the data at the DO port is the
valid data from the last read address.
Asserting READ, WRITE, and ERASE at the same time is not allowed. Multiple requests
are ignored and nothing is read from, written to, or erased in the UFM block. There is
no support for sequential read and page write in the parallel interface. For both the
read only and the read/write modes of the parallel interface, OSC_ENA is always
asserted, enabling the internal oscillator. Table 7–15 lists the parallel interface pins and
functions.
Table 7–15. Parallel Interface Signals
Pin
Description
Function
DI[15..0]
16-bit data Input
Receive 16-bit data in parallel. You can select an optional width of 3 to
16 bits using the ALTUFM megafunction.
DO[15..0]
16-bit data Output
Transmit 16-bit data in parallel. You can select an optional width of 3 to
16 bits using the ALTUFM megafunction.
ADDR[8..0]
Address Register
Operation sequence refers to the data that is pointed to by the address
register. You can determine the address bus width using the ALTUFM
megafunction.
nREAD
READ Instruction Signal
Initiates a read sequence.
nWRITE
WRITE Instruction Signal
Initiates a write sequence.
nERASE
ERASE Instruction Signal
Initiates a SECTOR-ERASE sequence indicated by the MSB of the
ADDR[] port.
nBUSY
BUSY Signal
Driven low to notify that it is not available to respond to any further
request.
DATA_VALID
Data Valid
Driven high to indicate that the data at the DO port is the valid data from
the last read address for read request.
Even though the ALTUFM megafunction allows you to select the address widths
range from 3 bits to 9 bits, the UFM block always expects a full 9 bits for the width of
the address register. Therefore, the ALTUFM megafunction will always pad the
remaining LSBs of the address register with '0's if the register width selected is less
than 9 bits. The address register will point to sector 0 if the address received at the
address register starts with a '0'. The address register will point to sector 1 if the
address received starts with a '1'.
Even though you can select an optional data register width of 3 to 16 bits using the
ALTUFM megafunction, the UFM block always expects full 16 bits width for the data
register. Reading from the data register always proceeds from MSB to LSB. The
ALTUFM megafunction always pads the remaining LSBs of the data register with 1s if
the user selects a data width of less than 16-bits.
MAX V Device Handbook
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
7–37
ALTUFM Parallel Interface Timing Specification
Figure 7–34 shows the timing specifications for the parallel interface. Table 7–16 lists
the parallel interface instruction signals. The nREAD, nWRITE, and nERASE signals are
active low signals.
Figure 7–34. Parallel Interface Timing Waveform
tCOMMAND
Command
tHNBUSY
nBusy
tHBUS
Data or Address Bus
Table 7–16. Parallel Interface Timing Parameters
Symbol
Description
Minimum (ns)
Maximum (ns)
tCOMMAND
The time required for the command signal (nREAD/nWRITE/nERASE)
to be asserted and held low to initiate a read/write/erase sequence
600
3,000
tHNBUSY
Maximum delay between command signal’s falling edge to the
nBUSY signal’s falling edge
—
300
tHBUS
The time that the data and address buses must be present at the
data input and address register ports after the command signal has
been asserted low
600
—
Instantiating Parallel Interface Using Quartus II ALTUFM_PARALLEL
Megafunction
Figure 7–35 shows the ALTUFM_PARALLEL megafunction symbol for a parallel
interface instantiation in the Quartus II software.
Figure 7–35. ALTUFM_PARALLEL Megafunction Symbol for Parallel Interface Instantiation
January 2011
Altera Corporation
MAX V Device Handbook
7–38
Chapter 7: User Flash Memory in MAX V Devices
Software Support for UFM Block
ALTUFM_PARALLEL megafunction is under the Memory Compiler folder on page
2a of the MegaWizard Plug-In Manager. On page 3, you can choose whether to
implement the Read/Write or Read Only mode for the UFM. You also have an option
to choose the width for address bus (up to 9 bits) and for the data bus (up to 16 bits).
You can specify the initial content of the UFM block on page 4 of the ALTUFM
MegaWizard Plug-In Manager as discussed in “Creating Memory Content File” on
page 7–39.
1
The UFM block’s internal oscillator is always running when the
ALTUFM_PARALLEL megafunction is instantiated for read/write interface. The
UFM block’s internal oscillator is disabled when the ALTUFM_PARALLEL
megafunction is instantiated for a read only interface.
None (Altera Serial Interface)
Select None for the interface protocol to use the dedicated UFM serial interface. The
built-in UFM interface uses 13 pins for the communication. The functional description
of the 13 pins are described in Table 7–4 on page 7–3. You can produce your own
interface design to communicate to/from the dedicated UFM interface and
implement it in the logic array.
Instantiating None Using Quartus II ALTUFM_NONE Megafunction
Figure 7–36 shows the ALTUFM_NONE megafunction symbol for None instantiation
in the Quartus II software.
Figure 7–36. ALTUFM_NONE Megafunction Symbol for None Instantiation
ALTUFM_NONE megafunction is under the Memory Compiler folder on page 2a of
the MegaWizard Plug-In Manager. You can specify the initial content of the UFM
block on page 3 of the ALTUFM MegaWizard Plug-In Manager as discussed in
“Creating Memory Content File”.
MAX V Device Handbook
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Creating Memory Content File
7–39
Creating Memory Content File
You can initialize the content of the UFM through a memory content file. The
Quartus II software supports two types of initial memory content file format: Memory
Initialization File (.mif) and Hexadecimal File (.hex). A new memory content file for
the UFM block can be created by clicking New on the File menu. Select the .mif or
.hex file in the Other Files tab.
After clicking OK, a dialog box appears. In this dialog box, the Number of words
represents the numbers of address lines while the Word size represents the data
width. To create a memory content file for the ALTUFM megafunction, enter 512 for
the number of words and 16 for the word size.
The memory content is written into a .hex file. On the Tools menu, click MegaWizard
Plug-In Manager. The memory content file (data.hex) is included on the respective
ALTUFM MegaWizard Plug-In Manager. Click Yes to use this file for the memory
content file. Click Browse to include the memory content file.
Memory Initialization for the ALTUFM_PARALLEL Megafunction
For the parallel interface, if a .hex file is used to initialize the memory content for the
ALTUFM megafunction, you must fully specify all 16 bits in each memory address,
regardless of the data width selected. If your data width is less than 16 bits wide, your
data must be placed in the MSBs of the data word and the remaining LSBs must be
padded with 1’s.
For an example, if address_width = 3 and data_width = 8 are selected for the
ALTUFM_PARALLEL megafunction, the .hex file should contain eight addresses of
data (23 addresses), each word containing 16 bits. If the initial content at the location
000 is intended to be 10101010, you should specify 1010101011111111 for address 000
in the .hex file.
1
This specification applies only to .hex files used with the parallel interface. .mifs do
not require you to fully specify 16 bits for each data word. However, both .mif and
.hex files require you to specify all addresses of data according to the address_width
selected in the megafunction.
Memory Initialization for the ALTUFM_SPI Megafunction
The same 16-bit data padding mentioned for ALTUFM_PARALLEL is required for
.hex files used with the SPI Base (8 bits) and Extended (16 bits) mode interface. In
addition, for SPI Base and Extended modes, you must fully specify memory content
for all 512 addresses (both sector 0 and sector 1) in the .mif and .hex files, even if
sector 1 is not used. You can put valid data for SPI Base mode addresses 0 to 255
(sector 0), and initialize sector 1 to all ones.
January 2011
Altera Corporation
MAX V Device Handbook
7–40
Chapter 7: User Flash Memory in MAX V Devices
Creating Memory Content File
Memory Initialization for the ALTUFM_I2C Megafunction
The MAX V UFM physical memory block contains a 16-bit wide and 512 deep (9-bit
address) array. The ALTUFM_I2C megafunction uses the following smaller array
sizes:
■
An 8-bit wide and 128 deep (7-bit address) mapping for 1 Kbit memory size
■
An 8-bit wide and 256 deep (8-bit address) mapping for 2 Kbits memory size
■
An 8-bit wide and 512 deep (9-bit address) mapping for 4 Kbits memory size
■
An 8-bit wide and 1,024 deep (10-bit address) mapping for 8 Kbits memory size
Altera recommends that you pad the .mif or .hex file for both address and data width
to fill the physical memory map for the UFM block and ensure the .mif or .hex file
represents a full 16-bit word size and a 9-bit address space.
Memory Map for 1-Kbit Memory Initialization
Figure 7–37 shows the memory map initialization for the ALTUFM_I2C megafunction
of 1-Kbit memory size. The ALTUFM_I2C megafunction byte address location of 00h
to 3Fh is mapped to the UFM block address location of 000h to 03Fh. The
ALTUFM_I2C megafunction byte address location of 40h to 7Fh is mapped to the
UFM block address location of 1C0h to 1FFh. Altera recommends that you pad the
unused address locations of the UFM block with all 1s.
Figure 7–37. Memory Map for 1-Kbit Memory Initialization
MIF or HEX File Contents – to represent
the actual data and address size for the UFM block
1-Kbit ALTUFM_I2C Megafunction
Logical Memory Contents
7Fh
Upper Half – Addresses
40h to 7Fh
1FFh
Address 40h in logical memory maps to
1C0h in the MIF/HEX file. Address 7Fh in logical
memory maps to 1FFh in the MIF/HEX file, and all
data in between follows the order in the
logical memory
1C0h
1BFh
This section of the UFM is unused –
the MIF/HEX file contents should be set to
all '1' for addresses 040h to 1BFh
40h
3Fh
Lower Half – Addresses
00h to 3Fh
040h
03Fh
00h
000h
MAX V Device Handbook
Address 00h in logical memory maps to
address 000h in the MIF/HEX file. Address 3Fh in
logical memory maps to 03Fh in the MIF/HEX file,
and all data in between follows the order in the
logical memory
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Creating Memory Content File
7–41
Memory Map for 2-Kbit Memory Initialization
Figure 7–38 shows the memory map initialization for the ALTUFM_I2C megafunction
of 2 Kbits of memory. The ALTUFM_I2C megafunction byte address location of 00h to
7Fh is mapped to the UFM block address location of 000h to 07Fh. The ALTUFM_I2C
megafunction byte address location of 80h to FFh is mapped to the UFM block address
location of 180h to 1FFh. Altera recommends that you pad the unused address location
of the UFM block with all 1s.
Figure 7–38. Memory Map for 2-Kbit Memory Initialization
MIF or HEX File Contents – to represent
the actual data and address size for the UFM block
2-Kbit ALTUFM_I2C Megafunction
Logical Memory Contents
1FFh
Address 80h in logical memory maps to
address 180h in the MIF/HEX file. FFh in logical
memory maps to 1FFh in the MIF/HEX file, and all
data in between follows the order in the
logical memory
FFh
Upper Half – Addresses
80h to FFh
180h
17Fh
This section of the UFM is unused –
the MIF/HEX file contents should be set to
all '1' for addresses 080h to 17Fh
80h
7Fh
080h
Lower Half – Addresses
00h to 7Fh
07Fh
Address 00h in logical memory maps to
address 000h in the MIF/HEX file. Address 7Fh in
logical memory maps to 07Fh in the MIF/HEX file,
and all data in between follows the order in the
logical memory
00h
000h
January 2011
Altera Corporation
MAX V Device Handbook
7–42
Chapter 7: User Flash Memory in MAX V Devices
Creating Memory Content File
Memory Map for 4-Kbit Memory Initialization
Figure 7–39 shows the memory map initialization for the ALTUFM_I2C megafunction
of 4-Kbit memory. The ALTUFM_I2C megafunction byte address location of 00h to
FFh is mapped to the UFM block address location of 000h to 0FFh. The ALTUFM_I2C
megafunction byte address location of 100h to 1FFh is mapped to the UFM block
address location of 100h to 1FFh.
Figure 7–39. Memory Map for 4-Kbit Memory Initialization
4-Kbit ALTUFM_I2C Megafunction
Logical Memory Contents
1FFh
MIF or HEX File Contents – to represent
the data and address size for the UFM block
1FFh
Address 100h in logical memory maps to
100h in the MIF/HEX file. Address 1FFh in logical
memory maps to 1FFh in the MIF/HEX file, and all
data in between follows the order in the
logical memory
Upper Half – Addresses
100h to 1FFh
100h
100h
FFh
0FFh
Address 00h in logical memory maps to
000h in the MIF/HEX file. Address FFh in logical
memory maps to 0FFh in the MIF/HEX file, and all
data in between follows the order in the
logical memory
Lower Half – Addresses
00h to FFh
00h
000h
Memory Map for 8-Kbit Memory Initialization
Figure 7–40 shows the memory map initialization for the ALTUFM_I2C megafunction
of 8-Kbit memory. The ALTUFM_I2C megafunction of 8-Kbit memory fully utilizes all
the memory locations in the UFM block.
Figure 7–40. Memory Map for 8-Kbit Memory Initialization
MIF or HEX File Contents - to represent the
actual data and address size for the UFM Block
8-Kbit ALTUFM_I2C Megafunction
Logical Memory Contents
3FFh
Upper Quarter Addresses
300h to 3FFh
300h
2FFh
Mid-Upper Quarter Addresses
200h to 2FFh
200h
1FFh
Mid-Lower Quarter Addresses
100h to 1FFh
100h
0FFh
Lower Quarter Addresses
000h to 0FFh
000h
1FFh
The upper quarter of
logical memory maps
to the upper byte of
sector 1. Address 300h
in logical memory
maps to address 100h
in physical memory
and all addresses
follow the order in
logical memory.
100h
The mid-upper quarter of
logical memory maps
to the lower byte of
sector 1. Address 200h
in logical memory
maps to address 100h
in physical memory
and all addresses
follow the order in
logical memory.
0FFh
The mid-lower quarter of
logical memory maps
to the lower byte of
sector 0. Address 100h
in logical memory
maps to address 000h
in physical memory
and all addresses
follow the order in
logical memory.
000h
The lower quarter of
logical memory maps
to the lower byte of
sector 0. Address 000h
in logical memory
maps to address 000h
in physical memory
and all addresses
follow the order in
logical memory.
Upper 8-bit (byte)
Lower 8-bit (byte)
16-bit data in UFM
MAX V Device Handbook
January 2011
Altera Corporation
Chapter 7: User Flash Memory in MAX V Devices
Simulation Parameters
7–43
Padding Data into Memory Map
The ALTUFM_I2C megafunction uses the upper 8 bits of the UFM 16-bit word;
therefore, the 8 least significant bits should be padded with 1s, as shown in
Figure 7–41.
Figure 7–41. Padding Data into Memory Map
1
0
1
0
1
0
1
8-bit valid data to be placed
in the upper byte
0
1
1
1
1
1
1
1
1
Pad the lower byte with eight '1's
Simulation Parameters
In the ALTUFM megafunction, you have an option to simulate the OSC output port at
the maximum or the minimum frequency during the design simulation. The
frequency chosen is only used as the timing parameter for the Quartus II simulator
and does not affect the real MAX V device OSC output frequency.
Document Revision History
Table 7–17 lists the revision history for this chapter.
Table 7–17. Document Revision History
Date
Version
Changes
January 2011
1.1
Updated “Oscillator” section.
December 2010
1.0
Initial release.
January 2011
Altera Corporation
MAX V Device Handbook
7–44
MAX V Device Handbook
Chapter 7: User Flash Memory in MAX V Devices
Document Revision History
January 2011
Altera Corporation
8. JTAG Boundary-Scan Testing in MAX V
Devices
December 2010
MV51008-1.0
MV51008-1.0
This chapter describes the IEEE Std.1149.1 (JTAG) boundary-scan testing for Altera®
MAX® V devices. The IEEE Std. 1149.1 BST circuitry available in MAX V devices
provides a cost-effective and efficient way to test systems that contain devices with
tight lead spacing. Circuit boards with Altera and other IEEE Std. 1149.1-compliant
devices can use EXTEST, SAMPLE/PRELOAD, and BYPASS modes to create serial patterns
that internally test the pin connections between devices and check device operation.
As PCBs become more complex, the requirement for thorough testing becomes
increasingly important. Advances in surface-mount packaging and PCB
manufacturing have resulted in smaller boards, making traditional test methods (for
example, external test probes and “bed-of-nails” test fixtures) harder to implement.
As a result, cost savings from PCB space reductions are sometimes offset by cost
increases in traditional testing methods.
In the 1980s, JTAG developed a specification for boundary-scan testing that was later
standardized as the IEEE Std. 1149.1 specification. This boundary-scan test (BST)
architecture offers the capability to efficiently test components on PCBs with tight
lead spacing.
BST architecture can test pin connections without using physical test probes and
capture functional data while a device is operating normally. Boundary-scan cells
(BSCs) in a device can force signals onto pins, or capture data from pin or core logic
signals. Forced test data is serially shifted into the BSCs. Captured data is serially
shifted out and externally compared to expected results.
Figure 8–1 shows the concept of boundary-scan testing.
Figure 8–1. IEEE Std. 1149.1 Boundary-Scan Testing
Boundary-Scan Cell
Serial
Data In
IC
Serial
Data Out
Pin Signal
Core
Logic
Core
Logic
Interconnection
to Be Tested
JTAG Device 1
JTAG Device 2
This chapter describes the following topics:
■
“IEEE Std. 1149.1 BST Architecture” on page 8–2
■
“IEEE Std. 1149.1 Boundary-Scan Register” on page 8–3
■
“IEEE Std. 1149.1 BST Operation Control” on page 8–6
■
“I/O Voltage Support in the JTAG Chain” on page 8–13
■
“Boundary-Scan Test for Programmed Devices” on page 8–14
© 2010 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX are Reg. U.S. Pat. & Tm. Off.
and/or trademarks of Altera Corporation in the U.S. and other countries. All other trademarks and service marks are the property of their respective holders as described at
www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera’s standard warranty, but
reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any
information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
MAX V Device Handbook
December 2010
Subscribe
8–2
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
IEEE Std. 1149.1 BST Architecture
■
“Disabling IEEE Std. 1149.1 BST Circuitry” on page 8–15
■
“Guidelines for IEEE Std. 1149.1 Boundary-Scan Testing” on page 8–15
■
“Boundary-Scan Description Language Support” on page 8–15
In addition to BST, you can use the IEEE Std. 1149.1 controller for in-system
programming for MAX V devices. MAX V devices support IEEE 1532 programming,
which uses the IEEE Std. 1149.1 test access port (TAP) interface. However, this chapter
only describes the BST feature of the IEEE Std. 1149.1 circuitry.
IEEE Std. 1149.1 BST Architecture
A MAX V device operating in IEEE Std. 1149.1 BST mode uses four required pins, TDI,
TDO, TMS, and TCK.
Table 8–1 lists the functions of each of these pins. MAX V devices do not have a TRST
pin.
Table 8–1. IEEE Std. 1149.1 Pin Descriptions
Pin
Description
Function
TDI (1)
Test data input
Serial input pin for instructions as well as test and
programming data. Data is shifted in on the rising edge of TCK.
Test data output
Serial data output pin for instructions as well as test and
programming data. Data is shifted out on the falling edge of
TCK. The pin is tri-stated if data is not being shifted out of the
device.
TMS (1)
Test mode select
Input pin that provides the control signal to determine the
transitions of the TAP controller state machine. Transitions
within the state machine occur at the rising edge of TCK.
Therefore, you must set up the TMS before the rising edge of
TCK. TMS is evaluated on the rising edge of TCK.
TCK (2)
Test clock input
The clock input to the BST circuitry. Some operations occur at
the rising edge, while others occur at the falling edge.
TDO
Notes to Table 8–1:
(1) The TDI and TMS pins have internal weak pull-up resistors
(2) The TCK pin has an internal weak pull-down resistor
The IEEE Std. 1149.1 BST circuitry requires the following registers:
MAX V Device Handbook
■
The instruction register determines which action to perform and which data
register to access.
■
The bypass register (which is a 1-bit long data register) provides a
minimum-length serial path between the TDI and TDO pins.
■
The boundary-scan register that is a shift register composed of all the BSCs of the
device.
December 2010
Altera Corporation
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
IEEE Std. 1149.1 Boundary-Scan Register
8–3
Figure 8–2 shows a functional model of the IEEE Std. 1149.1 circuitry.
Figure 8–2. IEEE Std. 1149.1 Circuitry
Instruction Register
TDI
TDO
UPDATEIR
CLOCKIR
SHIFTIR
Instruction Decode
TAP
Controller
TMS
TCK
UPDATEDR
CLOCKDR
SHIFTDR
Data Registers
Bypass Register
Boundary-Scan Register (1)
a
Device ID Register
ISP Registers
Note to Figure 8–2:
(1) For the boundary-scan register length in MAX V devices, refer to the JTAG and In-System Programmability in MAX V Devices chapter.
The TAP controller controls the IEEE Std. 1149.1 boundary-scan testing, as described
in “IEEE Std. 1149.1 BST Operation Control” on page 8–6. The TMS and TCK pins
operate the TAP controller and the TDI and TDO pins provide the serial path for the
data registers. The TDI pin also provides data to the instruction register, which then
generates the control logic for the data registers.
IEEE Std. 1149.1 Boundary-Scan Register
The boundary-scan register is a large serial shift register that uses the TDI pin as an
input and the TDO pin as an output. The boundary-scan register consists of 3-bit
peripheral elements that are associated with the I/O pins of the MAX V devices. You
can use the boundary-scan register to test the external pin connections or to capture
internal data.
December 2010
Altera Corporation
MAX V Device Handbook
8–4
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
IEEE Std. 1149.1 Boundary-Scan Register
Figure 8–3 shows how test data is serially shifted around the periphery of the IEEE
Std. 1149.1 device.
Figure 8–3. Boundary-Scan Register
Each peripheral
element is either an
I/O pin, dedicated
input pin, or
dedicated
configuration pin.
Internal Logic
TAP Controller
TDI
TMS
TCK
TDO
Boundary-Scan Cells of a MAX V Device I/O Pin
Except for the four JTAG pins and power pins, you can use all the pins of a MAX V
device (including clock pins) as user I/O pins and have a BSC. The 3-bit BSC consists
of a set of capture registers and a set of update registers. The capture registers can
connect to internal device data through the OUTJ and OEJ signals, while the update
registers connect to external data through the PIN_OUT and PIN_OE signals. The TAP
controller internally generates the SHIFT, CLOCK, and UPDATE global control signals for
the IEEE Std. 1149.1 BST registers; a decode of the instruction register generates the
MODE signal. The data signal path for the boundary-scan register runs from the serial
data in (SDI) signal to the serial data out (SDO) signal. The scan register begins at the
TDI pin and ends at the TDO pin of the device.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
IEEE Std. 1149.1 Boundary-Scan Register
8–5
Figure 8–4 shows the user I/O BSC for MAX V devices.
Figure 8–4. User I/O BSC with IEEE Std. 1149.1 BST Circuitry for MAX V Devices
SDO
PIN_IN
INJ
0
1
D
Q
Input
OEJ
0
1
D
From or To Device
I/O Cell Circuitry
And/Or Logic Core
Q
D
OE
D
Q
Output
D
Q
Output
CLOCK
UPDATE
OUTJ
0
1
SHIFT
Capture
Registers
SDI
PIN_OE
0
1
PIN_OUT
0
1
Q
OE
0
1
Pin
Output
Buffer
HIGHZ MODE
Global Signals
Update
Registers
Table 8–2 lists the capture and update register capabilities of all BSC within MAX V
devices.
Table 8–2. BSC Description for MAX V Devices (Note 1)
Captures
Drives
Pin Type
Output
Capture
Register
OE Capture
Register
Input Capture
Register
Output
Update
Register
OE Update
Register
Input Update
Register
User I/O
OUTJ
OEJ
PIN_IN
PIN_OUT
PIN_OE
—
Notes
Includes
user clocks
Note to Table 8–2:
(1) TDI, TDO, TMS, and TCK pins and all VCC and GND pin types do not have BSCs.
JTAG Pins and Power Pins
MAX V devices do not have BSCs for dedicated JTAG pins (TDI, TDO, TMS, and TCK)
and power pins (VCCINT, VCCIO, GNDINT, and GNDIO).
December 2010
Altera Corporation
MAX V Device Handbook
8–6
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
IEEE Std. 1149.1 BST Operation Control
IEEE Std. 1149.1 BST Operation Control
MAX V devices implement the SAMPLE/PRELOAD, EXTEST, BYPASS, IDCODE, USERCODE,
CLAMP and HIGHZ IEEE Std. 1149.1 BST instructions. The length of the BST instructions
is 10 bits. These instructions are described in detail later in this chapter.
f For a summary of the BST instructions and their instruction codes, refer to the JTAG
and In-System Programmability in MAX V Devices chapter.
The IEEE Std. 1149.1 TAP controller, a 16-state state machine clocked on the rising
edge of TCK, uses the TMS pin to control IEEE Std. 1149.1 operation in the device.
Figure 8–5 shows the TAP controller state machine.
Figure 8–5. IEEE Std. 1149.1 TAP Controller State Machine
TMS = 1
TEST_LOGIC/
RESET
TMS = 0
SELECT_DR_SCAN
SELECT_IR_SCAN
TMS = 1
TMS = 1
TMS = 0
TMS = 1
RUN_TEST/
IDLE
TMS = 0
TMS = 0
TMS = 1
TMS = 1
CAPTURE_IR
CAPTURE_DR
TMS = 0
TMS = 0
SHIFT_DR
SHIFT_IR
TMS = 0
TMS = 1
TMS = 1
TMS = 1
TMS = 1
EXIT1_IR
EXIT1_DR
TMS = 0
TMS = 0
PAUSE_IR
PAUSE_DR
TMS = 0
TMS = 1
TMS = 0
TMS = 1
TMS = 0
TMS = 0
EXIT2_IR
EXIT2_DR
TMS = 1
TMS = 1
TMS = 1
TMS = 1
UPDATE_DR
TMS = 0
MAX V Device Handbook
TMS = 0
UPDATE_IR
TMS = 0
December 2010
Altera Corporation
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
IEEE Std. 1149.1 BST Operation Control
8–7
When the TAP controller is in the TEST_LOGIC/RESET state, the BST circuitry is
disabled, the device is in normal operation, and the instruction register is initialized
with IDCODE as the initial instruction. During device power up, the TAP controller
starts in this TEST_LOGIC/RESET state. In addition, the TAP controller may be forced to
the TEST_LOGIC/RESET state by holding TMS high for five TCK clock cycles. After the
TEST_LOGIC/RESET state, the TAP controller remains in this state as long as TMS
continues to be held high while TCK is clocked.
Figure 8–6 shows the timing requirements for the IEEE Std. 1149.1 signals.
Figure 8–6. IEEE Std. 1149.1 Timing Waveforms (Note 1)
TMS
TDI
tJCP
tJCH
tJPSU
tJPH
tJCL
TCK
tJPZX
tJPCO
tJPXZ
TDO
tJSSU
Signal
to Be
Captured
tJSZX
tJSH
tJSCO
tJSXZ
Signal
to Be
Driven
Note to Figure 8–6:
(1) For timing parameter values, refer to the DC and Switching Characteristics for MAX V Devices chapter.
To start the IEEE Std. 1149.1 operation, select an instruction mode by advancing the
TAP controller to the shift instruction register (SHIFT_IR) state and shift in the
appropriate instruction code on the TDI pin.
Figure 8–7 shows the entry of the instruction code into the instruction register. From
the RESET state, TMS is clocked with the pattern 01100 to advance the TAP controller to
SHIFT_IR state.
Figure 8–7. Selecting the Instruction Mode
TCK
TMS
TDI
TDO
SHIFT_IR
TAP_STATE
RUN_TEST/IDLE
SELECT_IR_SCAN
SELECT_DR_SCAN
EXIT1_IR
CAPTURE_IR
TEST_LOGIC/RESET
December 2010
Altera Corporation
MAX V Device Handbook
8–8
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
IEEE Std. 1149.1 BST Operation Control
The TDO pin is tri-stated in all states except the SHIFT_IR and SHIFT_DR states. The TDO
pin is activated at the first falling edge of TCK after entering either of the shift states
and is tri-stated at the first falling edge of TCK after leaving either of the shift states.
When the SHIFT_IR state is activated, TDO is no longer tri-stated, and the initial state of
the instruction register is shifted out on the falling edge of TCK. TDO continues to shift
out the contents of the instruction register as long as the SHIFT_IR state is active. The
TAP controller remains in the SHIFT_IR state as long as TMS remains low.
During the SHIFT_IR state, an instruction code is entered by shifting data on the TDI
pin on the rising edge of TCK. You must clock the last bit of the OPCODE at the same time
that the next state, EXIT1_IR, is activated; EXIT1_IR is entered by clocking a logic high
on TMS. After in the EXIT1_IR state, TDO becomes tri-stated again. TDO is always
tri-stated except in the SHIFT_IR and SHIFT_DR states. After an instruction code is
entered correctly, the TAP controller advances to perform the serial shifting of test
data in one of three modes (SAMPLE/PRELOAD, EXTEST, or BYPASS).
For MAX V devices, there are weak pull-up resistors for TDI and TMS, and pull-down
resistors for TCK. However, in a JTAG chain, there might be some devices that do not
have internal pull-up or pull-down resistors. In this case, Altera recommends pulling
the TMS pin high (through an external 10-k resistor), and pulling TCK low (through an
external 1-k resistor) during BST or in-system programmability (ISP) to prevent the
TAP controller from going into an unintended state. Pulling-up the TDI signal
externally for the MAX V device is optional.
f For more information about the pull-up and pull-down resistors, refer to
AN 100: In-System Programmability Guidelines.
SAMPLE/PRELOAD Instruction Mode
SAMPLE/PRELOAD instruction mode allows you to take a snapshot of device data
without interrupting normal device operation. However, SAMPLE/PRELOAD instruction
mode is most often used to preload the test data into the update registers before
loading the EXTEST instruction.
During the capture phase, multiplexers preceding the capture registers select the
active device data signals and clocked data into the capture registers. The
multiplexers at the outputs of the update registers also select active device data to
prevent functional interruptions to the device.
During the shift phase, the boundary-scan shift register is formed by clocking data
through capture registers around the device periphery and then out of the TDO pin.
New test data can simultaneously be shifted into TDI and replace the contents of the
capture registers. During the update phase, data in the capture registers is transferred
to the update registers.You can then use this data in EXTEST instruction mode. For
more information, refer to “EXTEST Instruction Mode” on page 8–10.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
IEEE Std. 1149.1 BST Operation Control
8–9
Figure 8–8 shows the capture, shift, and update phases of SAMPLE/PRELOAD mode.
Figure 8–8. IEEE Std. 1149.1 BST SAMPLE/PRELOAD Mode
SDO
PIN_IN
INJ
0
1
D
Q
Input
OEJ
0
1
D
Q
D
OE
D
Q
Output
D
Q
Output
CLOCK
UPDATE
OUTJ
0
1
SHIFT
Capture
Registers
SDI
PIN_OE
0
1
PIN_OUT
0
1
Q
OE
0
1
Output
Buffer
HIGHZ MODE
Pin
Global Signals
Update
Registers
(Capture Phase)
SDO
PIN_IN
INJ
0
1
D
Q
Input
OEJ
0
1
D
Q
D
Q
OE
OE
D
Q
Output
D
Q
Output
SHIFT
CLOCK
UPDATE
SDI
Capture
Registers
PIN_OE
0
1
PIN_OUT
0
1
OUTJ
0
1
0
1
Output
Buffer
HIGHZ MODE
Pin
Global Signals
Update
Registers
(Shift and Update Phase)
SAMPLE/PRELOAD instruction code shifts in through the TDI pin. The TAP controller
advances to the CAPTURE_DR state and then to the SHIFT_DR state, where it remains if
TMS is held low. The data shifted out of the TDO pin consists of the data that was
present in the capture registers after the capture phase. New test data shifted into the
TDI pin appears at the TDO pin after being clocked through the entire boundary-scan
register.
December 2010
Altera Corporation
MAX V Device Handbook
8–10
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
IEEE Std. 1149.1 BST Operation Control
Figure 8–9 shows that the test data that shifted into TDI does not appear at the TDO pin
until after the capture register data that is shifted out. If TMS is held high on two
consecutive TCK clock cycles, the TAP controller advances to the UPDATE_DR state for
the update phase.
If you enable the device output enable feature but the DEV_OE pin is not asserted
during boundary-scan testing, the output enable boundary-scan registers of the BSCs
capture data from the core of the device during SAMPLE/PRELOAD. These values are not
high impedance, although the I/O pins are tri-stated.
Figure 8–9 shows the SAMPLE/PRELOAD waveforms.
Figure 8–9. SAMPLE/PRELOAD Shift Data Register Waveforms
TCK
TMS
TDI
TDO
SHIFT_IR
SHIFT_DR
TAP_STATE
EXIT1_IR
Instruction Code
SELECT_DR_SCAN
UPDATE_IR
Data stored in
CAPTURE_DR boundary-scan
register is shifted
out of TDO.
After boundry-scan
register data has been
shifted out, data
entered into TDI will
shift out of TDO.
EXIT1_DR
UPDATE_DR
EXTEST Instruction Mode
Use EXTEST instruction mode to check the external pin connections between devices.
Unlike SAMPLE/PRELOAD mode, EXTEST allows test data to be forced onto the pin
signals. By forcing known logic high and low levels on output pins, you can detect
opens and shorts at pins of any device in the scan chain.
EXTEST selects data differently than SAMPLE/PRELOAD. EXTEST chooses data from the
update registers as the source of the output and output enable signals. After the
EXTEST instruction code is entered, the multiplexers select the update register data;
thus, you can force the data stored in these registers from a previous EXTEST or
SAMPLE/PRELOAD test cycle onto the pin signals. In the capture phase, the results of this
test data are stored in the capture registers and then shifted out of TDO during the shift
phase. You can store the new test data in the update registers during the update
phase.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
IEEE Std. 1149.1 BST Operation Control
8–11
Figure 8–10 shows the capture, shift, and update phases of EXTEST mode.
Figure 8–10. IEEE Std. 1149.1 BST EXTEST Mode
SDO
PIN_IN
INJ
0
1
D
Q
Input
OEJ
0
1
D
Q
D
OE
D
Q
Output
D
Q
Output
CLOCK
UPDATE
OUTJ
0
1
SHIFT
Capture
Registers
SDI
PIN_OE
0
1
PIN_OUT
0
1
Q
OE
0
1
Output
Buffer
HIGHZ MODE
Pin
Global Signals
Update
Registers
(Capture Phase)
SDO
PIN_IN
INJ
0
1
D
Q
Input
OEJ
0
1
D
Q
D
Q
OE
OE
D
Q
Output
D
Q
Output
SHIFT
CLOCK
UPDATE
SDI
Capture
Registers
PIN_OE
0
1
PIN_OUT
0
1
OUTJ
0
1
0
1
Output
Buffer
HIGHZ MODE
Pin
Global Signals
Update
Registers
(Shift and Update Phase)
December 2010
Altera Corporation
MAX V Device Handbook
8–12
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
IEEE Std. 1149.1 BST Operation Control
Figure 8–11 resembles the SAMPLE/PRELOAD waveform diagram, except that the
instruction code for EXTEST is different. The data shifted out of TDO consists of the data
that was present in the capture registers after the capture phase. New test data shifted
into the TDI pin appears at the TDO pin after being clocked through the entire
boundary-scan register.
Figure 8–11. EXTEST Shift Data Register Waveforms
TCK
TMS
TDI
TDO
SHIFT_IR
SHIFT_DR
TAP_STATE
EXIT1_IR
Instruction Code
SELECT_DR_SCAN
Data stored in
CAPTURE_DR boundary-scan
register is shifted
UPDATE_IR
out of TDO.
After boundry-scan
register data has been
shifted out, data
entered into TDI will
shift out of TDO.
EXIT1_DR
UPDATE_DR
BYPASS Instruction Mode
You can activate BYPASS instruction mode with an instruction code made up of only
ones. Figure 8–12 shows how scan data passes through a device after the TAP
controller is in the SHIFT_DR state. In this state, data signals are clocked into the bypass
register from TDI on the rising edge of TCK and out of TDO on the falling edge of the
same clock pulse.
Figure 8–12. BYPASS Shift Data Register Waveforms
TCK
TMS
Bit 1
TDI
TDO
SHIFT_IR
TAP_STATE
Bit 2
Bit 3
Bit 1
Bit 2
Bit n
SHIFT_DR
EXIT1_IR
Instruction Code
SELECT_DR_SCAN
UPDATE_IR
CAPTURE_DR
Data shifted into TDI on
the rising edge of TCK is
shifted out of TDO on the
falling edge of the same
TCK pulse.
EXIT1_DR
UPDATE_DR
IDCODE Instruction Mode
Use IDCODE instruction mode to identify the devices in an IEEE Std. 1149.1 chain.
When you select IDCODE, the device identification register loads with the 32-bit
vendor-defined identification code. The device ID register is connected between the
TDI and TDO ports and the device IDCODE is shifted out.
f IDCODE instruction mode for MAX V devices are listed in the JTAG and In-System
Programmability in MAX V Devices chapter.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
I/O Voltage Support in the JTAG Chain
8–13
USERCODE Instruction Mode
Use USERCODE instruction mode to examine the user electronic signature (UES) within
the devices along an IEEE Std. 1149.1 chain. When you select this instruction, the
device identification register is connected between the TDI and TDO ports. The userdefined UES shifts into the device ID register in parallel from the 32-bit USERCODE
register. The UES then shifts out through the device ID register. The USERCODE
information is only available after the device is successfully configured.
Non-volatile USERCODE data is written to the configuration flash memory (CFM) block
and then written to the SRAM at power up. The USERCODE instruction reads the data
values from the SRAM. When you use real-time ISP to update the CFM block and
write new USERCODE data, executing the USERCODE instruction returns the USERCODE of
the current running design (stored in the SRAM), not the new USERCODE data. The
USERCODE of the new design (stored in the CFM) can only be read back correctly if a
power cycle or forced SRAM download has transpired after the real-time ISP update.
In the Quartus® II software, there is an Auto Usercode feature where you can choose
to use the checksum value of a programming file as the JTAG user code. If selected,
the checksum is automatically loaded to the USERCODE register.
To enable the Auto Usercode feature, follow these steps:
1. On the Assignments menu, click Device.
2. In the Device dialog box, click Device and Pin Options and click the General tab.
3. Turn on Auto Usercode.
CLAMP Instruction Mode
Use CLAMP instruction mode to allow the state of the signals driven from the pins to be
determined from the boundary-scan register while the bypass register is selected as
the serial path between the TDI and Tmv51008.fmDO ports. Data held in the boundaryscan register completely defines the state of all signals driven from the output pins.
However, CLAMP instruction mode will not override the I/O weak pull-up resistor or
the I/O bus hold if you have any of them selected.
HIGHZ Instruction Mode
Use HIGHZ instruction mode to set all of the user I/O pins to an inactive drive state.
These pins are tri-stated until you execute a new JTAG instruction. When you select
this instruction, the bypass register is connected between the TDI and TDO ports. HIGHZ
instruction mode will not override the I/O weak pull-up resistor or I/O bus hold if
you have any of them selected.
I/O Voltage Support in the JTAG Chain
There can be several different Altera or non-Altera devices in a JTAG chain. However,
you must pay attention to whether or not the chain contains devices with different
VCCIO levels. The TDO pin of a device drives out at the voltage level according to the
VCCIO of the device. For MAX V devices, the TDO pin drives out at the voltage level
according to the V CCIO of I/O Bank 1. Although the devices may have different VCCIO
December 2010
Altera Corporation
MAX V Device Handbook
8–14
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
Boundary-Scan Test for Programmed Devices
levels, the devices can interface with each other. For example, a device with 3.3-V
VCCIO can drive to a device with 5.0-V VCCIO because 3.3 V meets the minimum VIH on
transistor-to-transistor logic (TTL)-level input for the 5.0-V VCCIO device. JTAG pins
on MAX V devices can support 1.5-, 1.8-, 2.5-, or 3.3-V input levels, depending on the
VCCIO voltage of I/O Bank 1.
f For more information about MultiVolt I/O support, refer to the MAX V Device
Architecture chapter.
You can interface the TDI and TDO lines of the JTAG pins of devices that have different
VCCIO levels by inserting a level shifter between the devices. If possible, the JTAG
chain must be built such that a device with a higher VCCIO level drives to a device with
an equal or lower VCCIO level. By building the JTAG chain in this manner, a level
shifter may be required only to shift the TDO level to a level acceptable to the JTAG
tester.
Figure 8–13 shows the JTAG chain of mixed voltages and how a level shifter is
inserted in the chain.
Figure 8–13. JTAG Chain of Mixed Voltages
Must be 5.0-V
Tolerant
Must be 3.3-V
Tolerant
TDI
5.0-V
VCCIO
3.3-V
VCCIO
2.5-V
VCCIO
TDO
Level
Shifter
1.5-V
VCCIO
1.8-V
1.8-V
VCCIO
V
CCIO
Tester
Shift TDO to Level
Accepted by Tester
if Necessary
Must be 1.8-V
Tolerant
Must be 2.5-V
Tolerant
Boundary-Scan Test for Programmed Devices
For a programmed device, the input buffers are turned off by default for I/O pins that
are set as output only in the design file. You cannot sample on the programmed device
output pins with the default boundary-scan description language (BSDL) file when
the input buffers are turned off.
For boundary-scan testing, you can set the Quartus II software to always enable the
input buffers on a programmed device so it behaves the same as an unprogrammed
device, allowing sample function on output pins in the design. This aspect can cause
slight increase in standby current as the unused input buffer is always on.
To enable the unused input buffers on a programmed device, follow these steps:
1. On the Assignments menu, click Settings.
2. Under Category, select Assembler.
3. Turn on Always Enable Input Buffers.
MAX V Device Handbook
December 2010
Altera Corporation
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
Disabling IEEE Std. 1149.1 BST Circuitry
8–15
Disabling IEEE Std. 1149.1 BST Circuitry
You can enable the IEEE Std. 1149.1 BST circuitry for MAX V devices after device
powers up. You must enable this circuitry only if you use the BST or ISP features. This
section describes how to disable the IEEE Std. 1149.1 circuitry to ensure that the
circuitry is not inadvertently enabled when it is not required.
Table 8–3 lists the pin connections necessary for disabling JTAG in MAX V devices
that have dedicated IEEE Std. 1149.1 pins.
Table 8–3. Disabling IEEE Std. 1149.1 Circuitry for MAX V Devices
JTAG Pins (1)
TMS
TCK
TDI
TDO
VCC (2)
GND (3)
VCC (2)
Leave Open
Notes to Table 8–3:
(1) There is no software option to disable JTAG in MAX V devices. The JTAG pins are dedicated.
(2) VCC refers to VCCIO of Bank 1.
(3) The TCK signal may also be tied high. If TCK is tied high, power-up conditions must ensure that TMS is pulled high
before TCK. Pulling TCK low avoids this power-up condition.
Guidelines for IEEE Std. 1149.1 Boundary-Scan Testing
When performing boundary-scan testing with IEEE Std. 1149.1 devices, use the
following guidelines:
■
1
If a pattern (for example, a 10-bit 1010101010 pattern) does not shift out of the
instruction register through the TDO pin during the first clock cycle of the SHIFT_IR
state, the proper TAP controller state has not been reached. To solve this problem,
try one of the following procedures:
■
Verify that the TAP controller has reached the SHIFT_IR state correctly. To
advance the TAP controller to the SHIFT_IR state, return to the RESET state and
clock the code 01100 on the TMS pin.
■
Check the connections to the VCC, GND, and JTAG pins on the device.
■
Perform a SAMPLE/PRELOAD test cycle before the first EXTEST test cycle to ensure that
known data is present at the device pins when EXTEST mode is entered. If the OEJ
update register contains a 0, the data in the OUTJ update register will be driven out.
The state must be known and correct to avoid contention with other devices in the
system.
■
Do not perform EXTEST and SAMPLE/PRELOAD tests during ISP. These instructions
are supported before and after ISP but not during ISP.
If problems persist, contact Technical Support.
Boundary-Scan Description Language Support
The BSDL—a subset of VHDL—provides a syntax that allows you to describe the
features of an IEEE Std. 1149.1 BST-capable device that can be tested. Test software
development systems then use the BSDL files for test generation, analysis, failure
diagnostics, and in-system programming.
December 2010
Altera Corporation
MAX V Device Handbook
8–16
Chapter 8: JTAG Boundary-Scan Testing in MAX V Devices
Document Revision History
f For more information, or to receive BSDL files for IEEE Std. 1149.1-compliant MAX V
devices, refer to the IEEE 1149.1 BSDL Files page on the Altera website.
Document Revision History
Table 8–4 shows the revision history for this chapter.
Table 8–4. Document Revision History
Date
December 2010
MAX V Device Handbook
Version
1.0
Changes
Initial release.
December 2010
Altera Corporation
Additional Information
This chapter provides additional information about the document and Altera.
Document Revision History
The following table shows the revision history for this document.
Date
Version
Changes
January 2011
1.1
Updated MAX V Device Family Overview, DC and Switching Characteristics for
MAX V Devices, and User Flash Memory in MAX V Devices chapters.
December 2010
1.0
Initial release.
How to Contact Altera
To locate the most up-to-date information about Altera® products, refer to the
following table.
Contact (1)
Technical support
Technical training
Product literature
Contact Method
Address
Website
www.altera.com/support
Website
www.altera.com/training
Email
[email protected]
Website
www.altera.com/literature
Non-technical support (General)
Email
[email protected]
(Software Licensing)
Email
[email protected]
Note to Table:
(1) You can also contact your local Altera sales office or sales representative.
Typographic Conventions
The following table shows the typographic conventions this document uses.
Visual Cue
Meaning
Bold Type with Initial Capital
Letters
Indicate command names, dialog box titles, dialog box options, and other GUI
labels. For example, Save As dialog box. For GUI elements, capitalization matches
the GUI.
bold type
Indicates directory names, project names, disk drive names, file names, file name
extensions, software utility names, and GUI labels. For example, \qdesigns
directory, D: drive, and chiptrip.gdf file.
Italic Type with Initial Capital Letters
Indicate document titles. For example, Stratix IV Design Guidelines.
Indicates variables. For example, n + 1.
italic type
May 2011
Altera Corporation
Variable names are enclosed in angle brackets (< >). For example, <file name> and
<project name>.pof file.
MAX V Device Handbook
Info–2
Additional Information
Typographic Conventions
Visual Cue
Meaning
Initial Capital Letters
Indicate keyboard keys and menu names. For example, the Delete key and the
Options menu.
“Subheading Title”
Quotation marks indicate references to sections within a document and titles of
Quartus II Help topics. For example, “Typographic Conventions.”
Indicates signal, port, register, bit, block, and primitive names. For example, data1,
tdi, and input. The suffix n denotes an active-low signal. For example, resetn.
Courier type
Indicates command line commands and anything that must be typed exactly as it
appears. For example, c:\qdesigns\tutorial\chiptrip.gdf.
Also indicates sections of an actual file, such as a Report File, references to parts of
files (for example, the AHDL keyword SUBDESIGN), and logic function names (for
example, TRI).
r
An angled arrow instructs you to press the Enter key.
1., 2., 3., and
a., b., c., and so on
Numbered steps indicate a list of items when the sequence of the items is important,
such as the steps listed in a procedure.
■ ■ ■
Bullets indicate a list of items when the sequence of the items is not important.
1
The hand points to information that requires special attention.
?
A question mark directs you to a software help system with related information.
f
The feet direct you to another document or website with related information.
c
A caution calls attention to a condition or possible situation that can damage or
destroy the product or your work.
w
A warning calls attention to a condition or possible situation that can cause you
injury.
The envelope links to the Email Subscription Management Center page of the Altera
website, where you can sign up to receive update notifications for Altera documents.
MAX V Device Handbook
May 2011
Altera Corporation