MODEL 62 1 1/4” Diameter Single Turn Cermet Trimming Potentiometer ELECTRICAL Standard Resistance Range, Ohms Standard Resistance Tolerance Input Voltage, Maximum Slider Current, Maximum Power Rating, Watts End Resistance, Maximum Actual Electrical Travel, Nominal Dielectric Strength Insulation Resistance, Minimum Resolution Contact Resistance Variation, Maximum 10 to 1Meg ±10% (<100 Ohms = ±20%) 200 Vdc or rms not to exceed power rating 100mA or within rated power, whichever is less 0.5 at 70°C derating to 0 at 125°C 2 Ohms 220° 600Vrms 100 Megohms Essentially infinite 1% or 1 Ohm, whichever is greater ENVIRONMENTAL Seal Temperature Coefficient, Maximum Operating Temperature Range Thermal Shock Moisture Resistance Shock, 6ms Sawtooth Vibration High Temperature Exposure Rotational Life Load Life at 0.5 Watts Resistance to Solder Heat 85°C Fluorinert® (No Leaks) ±100ppm/°C –55°C to +125°C 5 cycles, –55°C to +125°C (1% ∆RT, 1% ∆VR) Ten 24 hour cycles (1% ∆RT, IR 100 Megohms Min.) 100G’s (1% ∆RT, 1% ∆VR) 20G’s, 10 to 2,000 Hz (1% ∆RT, 1% ∆VR) 250 hours at 125°C (2% ∆RT, 2% ∆VR) 200 cycles (2% ∆RT) 1,000 hours at 70°C (2% ∆RT) 260°C for 10 sec. (1% ∆RT) MECHANICAL Mechanical Stops Torque, Starting Maximum Weight, Nominal Solid 3 oz.-in. (0.021 N-m) .02 oz. (0.60 grams) Fluorinert® is a registered trademark of 3M Company. Specifications subject to change without notice. 1-31 Model 62 TOP ADJUSTMENT (Inch/mm) Model 62P, 62PF Model 62P (1) (3) .007 Min. 0.178 Standoff 3 Places .025 0.635 .10 2.54 90° ± 5° .210 5.08 A Standoff Plastic 62PF Dim . A .312±.062 7.92±1.57 .625 Min. 15.87 .250 ± .020 Dia. 6.350 ± 0.508 Electric Adjustment .110 ± .005 .025 ± .005 Long X 2.794 ± 0.127 0.635 ± 0.127 Housing: Metal .10 2.54 Terminal Pins (3) Solderable .017 ± .003 Dia. 0.432 ± 0.076 (2) Wide X .035 ± .005 ± Deep Slot 0.889 ± 0.127 Note: Model 62P dimensions applicable to all models except as noted. Model 62B 3 Model No. & Resistance Value on either surface .10 2.54 Case: Plastic .015 Min. 0.381 Standoff 3 Pls. .10 2.54 (1) (3) .30 7.62 2 .360 Max. 9.144 .20 Max. 5.08 ;;; 1 .280 Max. 7.112 (2) .25 6.35 Min. .150 ± .015 3.810 ± 0.381 .017 ± .003 Dia. 0.432 ± 0.076 Solderable Pins (3) Model 62M .10 2.54 .210 5.08 .19 Min. 4.83 .10 2.54 (3) (1) (2) .10 2.54 Terminal Pins (3) Solderable .017 ± .003 Dia. 0.432 ± 0.076 1-32 Model 62 STANDARD RESISTANCE VALUES, OHMS 10 20 50 100 200 500 1K 2K 5K 10K 20K 25K 50K 100K 200K 250K 1 500K 1Meg PACKAGING Standard: Plastic Bags Capacity = 100 Units ORDERING INFORMATION Standard: 62 P R 10K LF RoHS Compliant Product Code - Optional Model Series Pin Style Resistance Value Resistance Prefix NOTES CIRCUIT DIAGRAM Metric equivalents, based on 1 inch = 25.4mm are rounded to the same number of significant figures as in the original English units and are provided for general information only. (2) (1) INCH mm (3) Tolerances unless otherwise specified: Linear = ± .01 inches (.25mm) Angular = ± 2 degrees CW 1-33 Model 62