74LCX16374 LOW VOLTAGE CMOS 16-BIT D-TYPE FLIP-FLOP (3-STATE) WITH 5V TOLERANT INPUTS AND OUTPUTS ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 5V TOLERANT INPUTS AND OUTPUTS HIGH SPEED : fMAX = 150MHz (MIN.) at VCC = 3V POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 24mA (MIN) at VCC = 3V PCI BUS LEVELS GUARANTEED AT 24 mA BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 2.0V to 3.6V (1.5V Data Retention) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 16374 LATCH-UP PERFORMANCE EXCEEDS 500mA (JESD 17) ESD PERFORMANCE: HBM > 2000V (MIL STD 883 method 3015); MM > 200V TSSOP ORDER CODES PACKAGE TSSOP TUBE T&R 74LCX16374TTR PIN CONNECTION DESCRIPTION The 74LCX16374 is a low voltage CMOS 16 BIT D-TYPE FLIP-FLOP with 3 STATE OUTPUTS NON INVERTING fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for low power and high speed 3.3V applications; it can be interfaced to 5V signal environment for both inputs and outputs. These 16 bit D-TYPE flip-flops are controlled by two clock inputs (nCK) and two output enable inputs(nOE). On the positive transition of the (nCK), the nQ outputs will be set to the logic state that were setup at the nD inputs. While the (nOE) input is low, the 8 outputs (nQ) will be in a normal state (high or low logic level) and while high level the outputs will be in a high impedance state. Any output control does not affect the internal operation of flip flops; that is, the old data can be retained or the new data can be entered even while the outputs are off. It has same speed performance at 3.3V than 5V AC/ACT family, combined with a lower power consumption. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. February 2003 1/10 74LCX16374 INPUT AND OUTPUT EQUIVALENT CIRCUIT IEC LOGIC SYMBOLS PIN DESCRIPTION PIN No SYMBOL 1 1OE NAME AND FUNCTION 3 State Output Enable Input (Active LOW) 2, 3, 5, 6, 8, 9, 1Q0 to 1Q7 3-State Outputs 11, 12 13, 14, 16, 17, 2Q0 to 2Q7 3-State Outputs 19, 20, 22, 23 24 2OE 3 State Output Enable Input (Active LOW) 25 2CK Latch Enable Input 36, 35, 33, 32, 2D0 to 2D7 Data Inputs 30, 29, 27, 26 47, 46, 44, 43, 1D0 to 1D7 Data Inputs 41, 40, 38, 37 48 1CK Latch Enable Input 4, 10, 15, 21, GND Ground (0V) 28, 34, 39, 45 7, 18, 31, 42 VCC Positive Supply Voltage TRUTH TABLE INPUTS OE CK D Q H X X Z L X NO CHANGE* L L L L H H X : Don‘t Care Z : High Impedance 2/10 OUTPUT 74LCX16374 LOGIC DIAGRAM This logic diagram has not to be used to estimate propagation delays ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage (OFF State) VO DC Output Voltage (High or Low State) (note 1) VCC IIK DC Input Diode Current IOK DC Output Diode Current (note 2) -0.5 to +7.0 V -0.5 to VCC + 0.5 - 50 V mA - 50 mA IO DC Output Current ± 50 mA ICC DC Supply Current per Supply Pin ± 100 mA IGND DC Ground Current per Supply Pin ± 100 mA Tstg Storage Temperature -65 to +150 °C TL Lead Temperature (10 sec) 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 1) IO absolute maximum rating must be observed 2) VO < GND RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage (note 1) Value Unit 2.0 to 3.6 V 0 to 5.5 V VI Input Voltage VO Output Voltage (OFF State) 0 to 5.5 V VO Output Voltage (High or Low State) 0 to VCC V IOH, IOL High or Low Level Output Current (VCC = 3.0 to 3.6V) ± 24 mA IOH, IOL High or Low Level Output Current (VCC = 2.7V) ± 12 mA Top dt/dv Operating Temperature Input Rise and Fall Time (note 2) -55 to 125 °C 0 to 10 ns/V 1) Truth Table guaranteed: 1.5V to 3.6V 2) VIN from 0.8V to 2V at VCC = 3.0V 3/10 74LCX16374 DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Ioff IOZ ICC ∆ICC Input Leakage Current Power Off Leakage Current High Impedance Output Leakage Current Quiescent Supply Current ICC incr. per Input Min. Max. 2.0 -55 to 125 °C Min. Unit Max. 2.0 V 2.7 to 3.6 0.8 0.8 2.7 to 3.6 IO=-100 µA VCC-0.2 VCC-0.2 2.7 IO=-12 mA 2.2 2.2 IO=-18 mA 2.4 2.4 IO=-24 mA 2.2 2.2 V V 2.7 to 3.6 IO=100 µA 0.2 0.2 2.7 IO=12 mA 0.4 0.4 IO=16 mA 0.4 0.4 IO=24 mA 0.55 0.55 2.7 to 3.6 VI = 0 to 5.5V ±5 ±5 µA 0 VI or VO = 5.5V 10 10 µA 2.7 to 3.6 VI = VIH or VIL VO = 0 to VCC ±5 ±5 µA 2.7 to 3.6 VI = VCC or GND VI or VO= 3.6 to 5.5V 20 20 ± 20 ± 20 2.7 to 3.6 VIH = VCC - 0.6V 500 500 3.0 II -40 to 85 °C VCC (V) 3.0 VOL Value V µA µA DYNAMIC SWITCHING CHARACTERISTICS Test Condition Symbol VOLP VOLV Parameter Dynamic Low Level Quiet Output (note 1) TA = 25 °C VCC (V) 3.3 Value Min. CL = 50pF VIL = 0V, VIH = 3.3V Typ. 0.8 -0.8 Unit Max. V 1) Number of outputs defined as "n". Measured with "n-1" outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is measured in the LOW state. 4/10 74LCX16374 AC ELECTRICAL CHARACTERISTICS Test Condition Symbol Parameter tPLH tPHL Propagation Delay Time tPZL tPZH Output Enable Time to HIGH and LOW level Output Disable Time from HIGH and LOW level Set-Up Time, HIGH or LOW level (Dn to CK) Hold Time, HIGH or LOW level (Dn to CK) CK Pulse Width, HIGH or LOW tPLZ tPHZ tS th tW fMAX tOSLH tOSHL Clock Pulse Frequency Output To Output Skew Time (note1, 2) VCC (V) 2.7 3.0 to 3.6 2.7 CL (pF) RL (Ω) Value ts = tr (ns) 50 500 2.5 50 500 2.5 50 500 2.5 50 500 2.5 50 500 2.5 2.7 3.0 to 3.6 50 500 3.0 to 3.6 50 3.0 to 3.6 50 3.0 to 3.6 2.7 3.0 to 3.6 2.7 3.0 to 3.6 -55 to 125 °C Min. Max. Min. Max. 1.5 1.5 1.5 6.5 6.2 6.3 1.5 1.5 1.5 6.5 6.2 6.3 1.5 6.1 1.5 6.1 1.5 6.2 1.5 6.2 1.5 6.0 1.5 6.0 Unit ns ns ns 2.5 2.5 2.5 2.5 1.5 1.5 1.5 1.5 2.5 3.0 3.0 3.0 3.0 ns 500 2.5 170 150 MHz 500 2.5 2.7 3.0 to 3.6 -40 to 85 °C 1.0 ns ns 1.0 ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = | tPLHm - tPLHn|, tOSHL = | tPHLm - tPHLn|) 2) Parameter guaranteed by design CAPACITIVE CHARACTERISTICS Test Condition Symbol CIN COUT CPD Parameter Value TA = 25 °C VCC (V) Min. Typ. Unit Max. Input Capacitance 3.3 VIN = 0 to VCC 7 pF Output Capacitance 3.3 VIN = 0 to VCC 8 pF Power Dissipation Capacitance (note 1) 3.3 fIN = 10MHz VIN = 0 or VCC 20 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/16 (per circuit) 5/10 74LCX16374 TEST CIRCUIT TEST tPLH, tPHL SWITCH Open tPZL, tPLZ 6V tPZH, tPHZ GND CL = 50 pF or equivalent (includes jig and probe capacitance) RL = R1 = 500Ω or equivalent RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM 1 : PROPAGATION DELAYS, SETUP AND HOLD TIMES, MAXIMUM CLOCK FREQUENCY (f=1MHz; 50% duty cycle) 6/10 74LCX16374 WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) WAVEFORM 3 : PULSE WIDTH (f=1MHz; 50% duty cycle) 7/10 74LCX16374 TSSOP48 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. A MIN. TYP. 1.2 A1 0.05 0.047 0.15 A2 MAX. 0.002 0.006 0.9 0.035 b 0.17 0.27 0.0067 0.011 c 0.09 0.20 0.0035 0.0079 D 12.4 12.6 0.488 0.496 E 8.1 BSC E1 6.0 0.318 BSC 6.2 e 0.236 0.5 BSC 0.244 0.0197 BSC K 0˚ 8˚ 0˚ 8˚ L 0.50 0.75 0.020 0.030 A A2 A1 b K e L E c D E1 PIN 1 IDENTIFICATION 1 7065588C 8/10 74LCX16374 Tape & Reel TSSOP48 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 30.4 0.519 1.197 Ao 8.7 8.9 0.343 0.350 Bo 13.1 13.3 0.516 0.524 Ko 1.5 1.7 0.059 0.067 Po 3.9 4.1 0.153 0.161 P 11.9 12.1 0.468 0.476 9/10 74LCX16374 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com 10/10