74V1GU04 SINGLE INVERTER (SINGLE STAGE) ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 3.5 ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 1 µA (MAX.) at TA = 25 oC HIGH NOISE IMMUNITY: VNIH = VNIL = 10% VCC (MIN.) POWER DOWN PROTECTION ON INPUT SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 8 mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 5.5V IMPROVED LATCH-UP IMMUNITY DESCRIPTION The 74V1GU04 is an advanced high-speed CMOS SINGLE INVERTER fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. S (SOT23-5L) C (SC-70) ORDER CODE: 74V1GU04S 74V1GU04C As the internal circuit is composed of a single stage inverter, it can be used in analog application such a crystal oscillator. Power down protection is provided on input and 0 to 7V can be accepted on input with no regard to the supply voltage. This device can be used to interface 5V to 3V. PIN CONNECTION AND IEC LOGIC SYMBOLS October 1999 1/7 74V1GU04 INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 1 N.C. NAME AND FUNCT ION 2 1A Data Input 4 1Y Data Output 3 GND Ground (0V) 5 VCC Positive Supply Voltage Not Connected TRUTH TABLE A Y L H H L ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage -0.5 to VCC + 0.5 V IIK DC Input Diode Current - 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA ± 50 mA VCC ICC or IGND DC VCC or Ground Current Tstg Storage Temperature TL Lead Temperature (10 sec) -65 to +150 o 260 o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. RECOMMENDED OPERATING CONDITIONS Symbol Unit 2.0 to 5.5 V Input Voltage 0 to 5.5 V VO Output Voltage 0 to VCC Top Supply Voltage Valu e VI VCC 2/7 Parameter Operating Temperature -40 to +85 V o C 74V1GU04 DC SPECIFICATIONS Symb ol VIH VIL VOH VOL Parameter T est Cond ition s Min. ICC Typ . Un it -40 to 85 o C Max. Min . Max. High Level Input Voltage 2.0 1.7 1.7 3.0 to 5.5 0.8VCC 0.8VCC Low Level Input Voltage 2.0 0.3 0.3 3.0 to 5.5 0.2VCC 0.2VCC High Level Output Voltage Low Level Output Voltage Input Leakage Current Quiescent Supply Current V 2.0 I O =-50 µA 1.8 2.0 1.8 3.0 IO=-50 µA IO=-50 µA 2.7 3.0 2.7 4.5 4.0 4.5 4.0 3.0 IO=-4 mA 2.58 2.48 4.5 IO=-8 mA 3.94 3.8 2.0 I O=50 µA 0.0 0.2 0.2 3.0 IO=50 µA IO=50 µA 0.0 0.3 0.3 0.0 0.5 0.5 0.44 4.5 II Value T A = 25 o C V CC (V) V V V 3.0 IO=4 mA 0.36 4.5 IO=8 mA 0.36 0.44 0 to 5.5 VI = 5.5V or GND ±0.1 ±1.0 µA 5.5 VI = VCC or GND 1 10 µA AC ELECTRICAL CHARACTERISTICS (Input t r = tf =3 ns) Symb ol Parameter V CC (V) tPLH tPHL Propagation Delay Time Test Co ndition CL (pF ) Value T A = 25 o C 3.3 3.3(*) 5.0(**) 15 50 15 Typ . 5.0 7.5 3.5 (**) 50 5.0 (*) 5.0 Min. Un it -40 to 85 o C Max. 8.9 11.4 5.5 Min . 1.0 1.0 1.0 Max. 10.5 13.0 6.5 7.0 1.0 8.0 ns (*) Voltage range is 3.3V ± 0.3V (**) Voltage range is 5V ± 0.5V CAPACITIVE CHARACTERISTICS Symb ol Parameter T est Cond ition s Value o T A = 25 C Min. -40 to 85 C Typ . Max. 10 C IN Input Capacitance 5 CPD Power Dissipation Capacitance (note 1) 9 Un it o Min . Max. 10 pF pF 1) CPD isdefined as the value of the IC’sinternal equivalent capacitance which is calculated fromthe operating current consumption without load. (Referto Test Circuit).Average operating current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC 3/7 74V1GU04 TEST CIRCUIT CL = 15/50 pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM: PROPAGATION DELAYS (f=1MHz; 50% duty cycle) 4/7 74V1GU04 SOT23-5L MECHANICAL DATA mm DIM. MIN. TYP. mils MAX. MIN. TYP. MAX. A 0.90 1.45 35.4 57.1 A1 0.00 0.15 0.0 5.9 A2 0.90 1.30 35.4 51.2 b 0.35 0.50 13.7 19.7 C 0.09 0.20 3.5 7.8 D 2.80 3.00 110.2 118.1 E 2.60 3.00 102.3 118.1 E1 1.50 1.75 59.0 68.8 L 0.35 0.55 13.7 21.6 e 0.95 37.4 e1 1.9 74.8 5/7 74V1GU04 SC-70 MECHANICAL DATA mm DIM. MIN. 6/7 TYP. mils MAX. MIN. TYP. MAX. A 0.80 1.10 31.5 43.3 A1 0.00 0.10 0.0 3.9 A2 0.80 1.00 31.5 39.4 b 0.15 0.30 5.9 11.8 C 0.10 0.18 3.9 7.1 D 1.80 2.20 70.9 86.6 E 1.80 2.40 70.9 94.5 E1 1.15 1.35 45.3 53.1 L 0.10 0.30 3.9 11.8 e 0.65 25.6 e1 1.3 51.2 74V1GU04 Information furnished is believed to be accurate and reliable. However, STMicroelectronic s assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems withoutexpress written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 1999 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com . 7/7