74VHCT125A QUAD BUS BUFFERS (3-STATE) PRELIMINARY DATA ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 3.8 ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 4 µA (MAX.) at TA = 25 oC COMPATIBLE WITH TTL OUTPUTS: VIH = 2V (MIN), VIL = 0.8V (MAX) POWER DOWN PROTECTION ON INPUTS & OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 8 mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC (OPR) = 4.5V to 5.5V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 125 IMPROVED LATCH-UP IMMUNITY LOW NOISE: VOLP = 0.8V (Max.) DESCRIPTION The 74VHCT125A is an advanced high-speed CMOS QUAD BUS BUFFERS fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. M (Micro Package) T (TSSOP Package) ORDER CODES : 74VHCT125AM 74VHCT125AT This device requires the 3-STATE control input G to be set high to place the output into the high impedance state. Power down protection is provided on all inputs and outputs and 0 to 7V can be accepted on inputs with no regard to the supply voltage. This device can be used to interface 5V to 3V. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS August 1999 1/8 74VHCT125A INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL NAME AND FUNCT ION 1, 4, 10, 13 1G to 4G Output Enable Inputs 2, 5, 9, 12 1A to 4A Data Inputs 3, 6, 8, 11 1Y to 4Y Data Outputs 7 GND Ground (0V) 14 VCC Positive Supply Voltage TRUTH TABLE A G Y X H Z L L L H L H X:”H” or ”L” Z:High Impadance ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage (see note 1) -0.5 to +7.0 V VO DC Output Voltage (see note 2) -0.5 to VCC + 0.5 V IIK DC Input Diode Current - 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA ± 50 mA VCC ICC or IGND DC VCC or Ground Current Tstg TL Storage Temperature Lead Temperature (10 sec) -65 to +150 o 300 o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. 1) Output in OFF State 2) High or Low State RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage Unit V VI Input Voltage 0 to 5.5 V VO Output Voltage (see note 1) 0 to 5.5 V VO Output Voltage (see note 2) Top Operating Temperature dt/dv Input Rise and Fall Time (see note 3) (V CC = 5.0 ± 0.5V) 1) Output in OFF State 2) High or Low State 3)VIN from0.8V to 2 V 2/8 Valu e 4.5 to 5.5 0 to VCC -40 to +85 0 to 20 V o C ns/V 74VHCT125A DC SPECIFICATIONS Symb ol Parameter T est Cond ition s Min. 2 VIH High Level Input Voltage 4.5 to 5.5 VIL Low Level Input Voltage 4.5 to 5.5 VOH High Level Output Voltage VOL IOZ II Value T A = 25 o C V CC (V) Typ . Un it -40 to 85 o C Max. Min . Max. 2 0.8 V 0.8 V 4.5 I O =-50 µA 4.4 4.5 IO=-8 mA 3.94 Low Level Output Voltage 4.5 I O=50 µA 0.1 0.1 4.5 IO=8 mA 0.36 0.44 High Impedance Output Leakage Current 4.5 to 5.5 VI = VIH or VIL VO = 0V to 5.5V ±0.25 ±2.5 µA 0 to 5.5 VI = 5.5V or GND ±0.1 ±1.0 µA Input Leakage Current 4.5 4.4 V 3.8 0.0 V ICC Quiescent Supply Current 5.5 VI = VCC or GND 4 40 µA ∆ICC Additional Worst Case Supply Current 5.5 One Input at 3.4V, other input at VCC or GND 1.35 1.5 mA IOPD Output Leakage Current 0 VOUT = 5.5V 0.5 5.0 µA AC ELECTRICAL CHARACTERISTICS (Input t r = tf =3 ns) Symb ol Parameter tPLH tPHL Propagation Delay Time 5.0(*) 15 RL = 1KΩ Value T A = 25 o C Min. Typ . Max. 3.8 5.5 5.0 (*) 50 RL = 1KΩ 5.3 7.5 1.0 8.5 tPLZ tPHZ Output Disable Time tPZL tPZH Output Enable Time 5.0(*) 5.0(*) 5.0(*) 15 50 50 RL = 1KΩ RL = 1KΩ RL = 1KΩ 3.6 5.1 6.1 5.1 7.1 8.8 1.0 1.0 1.0 6.0 8.0 10.0 V CC (V) Test Co ndition CL (pF ) Un it -40 to 85 o C Min . Max. 1.0 6.5 ns ns ns (*) Voltage range is 5.0V ± 0.5V 3/8 74VHCT125A CAPACITIVE CHARACTERISTICS Symb ol Parameter Test Co nditions Valu e T A = 25 oC Min. Un it -40 to 85 o C T yp. Max. Input Capacitance 4 10 COUT Output Capacitance 10 pF CPD Power Dissipation Capacitance (note 1) 14 pF C IN Min. Max. 10 pF 1) CPD isdefined as the value of the IC’sinternal equivalent capacitance which is calculated fromthe operating current consumption without load. (Referto Test Circuit).Average operting current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC/4(per circuit) DYNAMIC SWITCHING CHARACTERISTICS Symb ol Parameter T est Cond ition s Dynamic Low Voltage Quiet Output (note 1, 2) 5.0 VIHD Dynamic High Voltage Input (note 1, 3) 5.0 VILD Dynamic Low Voltage Input (note 1, 3) 5.0 VOLP VOLV Value T A = 25 o C V CC (V) Min. -0.8 C L = 50 pF Un it -40 to 85 o C Typ . Max. 0.3 0.8 Min . Max. -0.3 2 V 0.8 1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 3.0V, (n -1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to3.0V. Inputs under test switching: 3.0V to threshold (VILD), 0V to threshold (VIHD), f=1MHz. TEST CIRCUIT T EST tPLH , tPHL SW IT CH Open tPZL , tPLZ VCC tPZH , tPHZ GND CL = 15/50 pF or equivalent (includes jig and probe capacitance) RL = R1 = 1KΩ orequivalent RT = ZOUT of pulse generator (typically 50Ω) 4/8 74VHCT125A WAVEFORM 1: PROPAGATION DELAYS (f=1MHz; 50% duty cycle) WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) 5/8 74VHCT125A SO-14 MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45 (typ.) D 8.55 8.75 0.336 0.344 E 5.8 6.2 0.228 0.244 e 1.27 e3 0.050 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.68 0.026 8 (max.) P013G 6/8 74VHCT125A TSSOP14 MECHANICAL DATA mm DIM. MIN. inch TYP. A MAX. MIN. TYP. MAX. 1.1 0.433 A1 0.05 0.10 0.15 0.002 0.004 0.006 A2 0.85 0.9 0.95 0.335 0.354 0.374 b 0.19 0.30 0.0075 0.0118 c 0.09 0.20 0.0035 0.0079 D 4.9 5 5.1 0.193 0.197 0.201 E 6.25 6.4 6.5 0.246 0.252 0.256 E1 4.3 4.4 4.48 0.169 0.173 0.176 e 0.65 BSC 0.0256 BSC K 0o 4o 8o 0o 4o 8o L 0.50 0.60 0.70 0.020 0.024 0.028 A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 7/8 74VHCT125A Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics 1999 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. http://www.st.com . 8/8