C&K 9000 Series Power Rocker and Lever Handle Switches Features/Benefits • Thermoset UL 94V-0 housing • Rugged construction • Variety of actuator and Typical Applications • Small equipment • Shut-off switch termination options • RoHS compliant Models Available Specifications Materials CONTACT RATING: 9201 Model: 6 AMPS @ 120 V AC or 28 V DC; 3 AMPS @ 250 V AC. 9221 Model: 10 AMPS @ 125 V AC or 28 V DC; 5 AMPS @ 250 V AC. CASE: Diallyl phthalate (DAP) (UL 94V-0). ACTUATOR: Nylon, black standard. FRAME-REAR MOUNT OPTIONS: Spring steel, black. ELECTRICAL LIFE: 25,000 make-and-break cycles at full load. BUSHING: Brass, nickel plated. CONTACT RESISTANCE: Below 10 m Ω typ. initial @ 2–4 V DC, 100 mA. INSULATION RESISTANCE: 109 Ω min. HOUSING: Stainless steel. SWITCH SUPPORT: Brass or steel, matte-tin plated. DIELECTRIC STRENGTH: 2,500 Vrms min. @ sea level. MOUNTING BRACKET: Stainless steel. OPERATING TEMPERATURE: –30ºC to 85ºC. END CONTACTS: 9201 Model: Coin silver, silver plated. 9221 Model: Silver cadmium oxide. SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E method 9 (1 hour steam aging). CENTER CONTACTS: Copper alloy, silver plated NOTE: Any models supplied with Q contact material are RoHS compliant. For the latest information regarding RoHS compliance, please go to: www.ittcannon.com/rohs. NOTE: Specifications and materials listed above are for switches with standard options. For information on specific and custom switches, consult Customer Service Center. ALL TERMINALS: 9201 Model: Copper alloy, silver plated. 9221 Model: Copper alloy, matte-tin plated. TERMINAL SEAL: Epoxy. HARDWARE: Nut, Screw & Lockwasher: Stainless steel. Standoff: Nylon standard, aluminum available, consult Customer Service Center. *Cadmium used in electrical contacts is acceptable for RoHS. Build-A-Switch To order, simply select desired option from each category and place in the appropriate box. Available options are shown and described on pages H-53 through H-57. For additional options not shown in catalog, consult Customer Service Center. Rocker Switch Function 9201 DP On-On, 6 Amps 9221 DP On-On, 10 Amps Actuator J1 Rocker J2 Lever J3 Rocker J37 Rocker with metal frame Terminations Z Solder lug (9201 only) AV2 Vertical right angle, PC thru-hole (9201 only) C PC Thru-hole (9201 only) Z4 Quick connect Contact Material Q Silver Seal E Epoxy D No Seal Actuator Color 2 Black 1 White 3 Red Frame Color 2 Black NONE No frame color required Dimensions are shown: Inch (mm) Specifications and dimensions subject to change H H–53 www.ittcannon.com C&K 9000 Series Power Rocker and Lever Handle Switches SWITCH FUNCTION SWITCH FUNCTION POS. 1 NO. POLES MODEL NO. CONNECTED TERMINALS POS. 2 POS. 1 POS. 2 RATING* SCHEMATIC 9201 6 AMPS ON ON 9221 10 AMPS ON ON DP 2-3,5-6 2-1,5-4 DPDT DPDT .140 DIA.(3,56ø) w/ J10 actuator 1.875 (47,62) w/ J10 actuator Part number shown: 9201J1ZQE2 1.625 (41,28) w/ J10 actuator Terminal Nos. Molded On Side Of Case All 9000 Series models meet international dimensional and electrical requirements. * See CONTACT MATERIAL, page H-58, for complete ratings. 9221 model must be ordered with Z4 terminations and D seal option. ACTUATOR COLOR ACTUATOR–PANEL MOUNT ACTUATOR OPTION CODE ACTUATOR COLOR 2 BLACK 1 WHITE 3 RED J1 ROCKER J2 LEVER Finish: Matte. Other colors, custom actuator markings and legends available, consult Customer Service Center. NOTE: Hardware: two each—mounting screws, nuts, lockwashers and standoffs for 1/8 inch thick panel are supplied standard on all switches with panel mounting brackets. Actuators available separately, see page H-56-57. Hardware available separately, see Technical Data section of this catalog. PANEL MOUNTING Rocker Dimensions are shown: Inch (mm) Specifications and dimensions subject to change H–54 www.ittcannon.com H C&K 9000 Series Power Rocker and Lever Handle Switches ACTUATOR COLOR ACTUATOR–PANEL MOUNT J3 ACTUATOR ROCKER OPTION CODE ACTUATOR COLOR 2 BLACK 1 WHITE 3 RED Actuator finish: Matte. Other colors, custom actuator markings and legends available, consult Customer Service Center. PANEL MOUNTING NOTE: Actuators available separately, see page H–56-57. Hardware: two each—mounting screws, nuts, lockwashers and standoffs for 1/8 inch thick panel are supplied standard on all switches with panel mounting brackets. Hardware available separately, see Technical Data section of this catalog. ACTUATOR COLOR ACTUATOR–REAR MOUNT J37 ACTUATOR FRAME COLOR ROCKER WITH METAL FRAME OPTION CODE .313 (7,95) ACTUATOR COLOR 2 BLACK 1 WHITE 3 RED OPTION CODE 2 FRAME COLOR BLACK Actuator finish: Matte. Frame finish: Gloss. Other colors, custom actuator markings and legends available, consult Customer Service Center. NOTE: Actuators & frames available separately, see page H-56-57. Hardware: two each—mounting screws, nuts, lockwashers and standoffs for 1/8 inch thick panel are supplied standard on all switches with panel mounting brackets. Hardware available separately, see Technical Data section of this catalog. PANEL MOUNTING Not available with AV2 termination. TERMINATIONS Z SOLDER LUG C Z4 PC THRU-HOLE QUICK CONNECT Rocker PC MOUNTING 9201 and 9221 NOTE: Only termination available with 9221 model. Must be ordered with D seal option. Mating terminal standard Nema .187" quick connect. 9201 Only 9201 Only Dimensions are shown: Inch (mm) Specifications and dimensions subject to change H H–55 www.ittcannon.com C&K 9000 Series Power Rocker and Lever Handle Switches TERMINATIONS AV2 VERTICAL RIGHT ANGLE, PC THRU-HOLE 9201J1AV2QE2 Vertical Actuation DPDT Terminal Nos. Molded On Side of Case 9201 Only NOTE: Terminal bend radii and lead-in manufacturing option. Terminal spacing greater than 3mm at all points. CONTACT MATERIAL OPTION CODE Q RoHS RoHS COMPLIANT * COMPATIBLE * YES MODEL CONTACT MATERIAL TERMINAL PLATING 9201 SILVER 1,2 SILVER OR TIN 2,5 9221 SILVER CADMIUM OXIDE 3,4,0 TIN 5 YES RATINGS 6 AMPS @120 V AC OR 28 V DC; 3 AMPS @ 250 V AC. POWER 10 AMPS @125 V AC OR 28 V DC; 5 AMPS @ 250 V AC. * Note: See Technical Data section of this catalog for RoHS compliant and compatible definitions and specifications. 1 END CONTACTS: Coin silver, silver plated. 2 CENTER CONTACTS & ALL TERMINALS: Copper alloy, silver plated. 3 END CONTACTS: Silver cadmium oxide. NOTE: Any models supplied with Q contact material is RoHS compliant. For the latest information regarding RoHS compliance, please go to: www.ittcannon.com/rohs. 4 CENTER CONTACTS: Copper alloy, silver plated. 5 Z4 TERMINALS ONLY: Copper alloy, tin plated. All 9000 Series models meet international dimensional and electrical requirements. 9221 model must be ordered with Z4 terminations and D seal option. 6 Cadmium used for electrical contacts is acceptable for RoHS. SEAL E D EPOXY SEAL NO EPOXY SEAL Rocker Must be ordered with 9221 model and Z4 termination. Not available with 9221 model or Z4 terminations. Dimensions are shown: Inch (mm) Specifications and dimensions subject to change H–56 www.ittcannon.com H C&K 9000 Series Power Rocker and Lever Handle Switches AVAILABLE HARDWARE Panel mounting hardware for rocker and lever handle switches is available separately. Mounting hardware consists of two screws, two nuts, two standoffs and two lockwashers per switch, and is available for panel thicknesses of 1/16, 3/32 and 1/8 inch. See part numbers below. SCREW TYPICAL ASSEMBLY PANEL THICKNESS STAND-OFF LENGTH STAND-OFF LOCKWASHER NUT J1 & J2 actuators PART NO. PANEL THK. 761101000 1/16 IN. (1,59) STANDOFF LENGTH .295 (7,49) 761102000 3/32 IN. (2,38) .264 (6,71) 761103000 1/8 IN. (3,18) .233 (5,92) J1 Actuator J2 Actuator J3, J37 Actuators PART NO. PART NO. PART NO. 776A01000 WHITE 776A02263 BLACK 776A03000 RED 760501000 WHITE 760502263 BLACK 760503000 RED 766601000 WHITE 766602263 BLACK 766603000 RED Material: Nylon Finish: Matte Material: Nylon Finish: Matte Material: Nylon Finish: Matte J37 Actuators NOTE: Additional nuts, screws and lockwashers available separately, see Technical Data section of this catalog. Other colors available, consult Customer Service Center. PART NO. 445400746 BLACK ENAMEL 445400747 WHITE ENAMEL Rocker Material: Spring Steel Dimensions are shown: Inch (mm) Specifications and dimensions subject to change H H–57 www.ittcannon.com