Using 1 Install the Latest Software ADDITIONAL INFORMATION Install the MPLAB IDE software onto your PC using the MPLAB IDE CD-ROM or download the software from the MPLAB IDE page of the Microchip web site (www.microchip.com/MPLAB). Check the latest Release Notes for additional information. Circuitry and Connector Pinouts Target Connector Pinout 2 Configure PC USB Communications Modular Connector Pin 1 2 3 4 5 6 Standard Connection At Target Connect MPLAB ICD 3 In-Circuit Debugger to a PC USB port via a USB cable. If the drivers do not install automatically, then install the drivers as instructed in: C:\Program Files\Microchip\MPLAB IDE\ICD 3\ Drivers\ddri.htm. Note: If a USB hub is used, the hub must be powered with its own power supply. 2 4 6 MPLAB ICD 3 RJ-11 Jack Pinout Microcontroller Pin MCLR/VPP VDD Ground PGD (ICSPDAT) PGC (ICSPCLK) PGM (LVP) Pin PGM PGC PGD Ground VDD MCLR/VPP 1 2 3 4 5 6 Signal 1 2 3 4 5 6 1 3 5 Bottom View Of Target Board 3 Use the ICD 3 Test Interface Board ICD 3 Test Interface Board Target Circuit Design Precautions Correct Target VDD (tVDD) USB/Power From PC XTAL* Target Application Device VPP/MCLR Use the supplied ICD 3 Test Interface Board to verify that the MPLAB ICD 3 is functioning properly: 1. Connect the ICD 3 Test Interface board to the debugger using the modular cable. 2. Ensure that “MPLAB ICD 3” is selected on either the Debugger or Programmer menu in MPLAB IDE. 3. From that menu, select “Settings”, Status tab, then click on Run ICD 3 Test Interface. The status (pass/fail) is displayed in the Output window. If a pass message is displayed, the MPLAB ICD 3 is functioning properly. PGC PGD VDD 4.7 10 kΩ Typical tVDD 2 1 5 4 3 VPP tVDD 4.7 kΩ tVDD AVSS** USB from PC Power Target Application PC Board AVSS** VSS Target Application PC Board Recommended Settings COMPONENT Oscillator 1. 2. 3. 4. 5. Launch MPLAB IDE. Load your project or use the Project Wizard to create a new one. Build your project based on your configurations and options. Attach the MPLAB ICD 3 to the PC using the USB cable. Select the MPLAB ICD 3 as either a debugger (Debugger>Select Tool>ICD 3) or as a programmer (Programmer>Select Programmer>ICD 3). 6 Program and Debug Processor Pak Standard Adapter 1. Program your device. 2. As a programmer, MPLAB ICD 3 will automatically run your code. As a debugger, you can run, halt, single step and set breakpoints in your code. Device-ICE Power WDT Code-Protect Table Read Protect LVP BOD JTAG AVDD and AVSS PGCx/PGDx Programming SETTING •OSC bits set properly •Running Supplied by target Disabled (device dependent) Disabled Disabled Disabled VDD > BOD VDD min Disabled Must be connected Proper channel selected, if applicable VDD voltage levels meet programming specs Note: See the MPLAB ICD 3 User’s Guide for more component and setting information. Reserved Resources For information on reserved resources used by the debugger, see the MPLAB ICD 3 on-line help. USB from PC Device-ICE Power 2 1 5 4 3 tVDD 5 Build Your Project Alternate Debugger System Configuration Using an ICE Device Transition Socket V DD PGC PGD • Do not use greater than 100 F capacitance on VDD – depending on the overall load, it will prevent the target from powering quickly when MPLAB ICD 3 is the source of power. • Do not use capacitors on MCLR – they will prevent fast transitions of VPP. • Do not use pull-ups on PGC/PGD – they will divide the voltage levels since these lines have 4.7 k pull-down resistors in MPLAB ICD 3. • Do not use multiplexing on PGC/PGD – they are dedicated for communications to MPLAB ICD 3. • Do not use capacitors on PGC/PGD – they will prevent fast transitions on data and clock lines during programming and debug communications. • Do not use diodes on PGC/PGD – they will prevent bidirectional communication between MPLAB ICD 3 and the target PIC® MCU. *Target device must be running with an oscillator for the debugger to function as a debugger. **If the device has AVDD and AVSS lines, they must be connected for the debugger to operate. Target Device or PIM OR XTAL* 4.7 kΩ Typical Debugger System – Device with on-board ICE circuitry ICD Header VPP/MCLR AVDD** tVDD VSS 1. Ensure the MPLAB ICD 3 is attached to the PC using the USB cable, if not already. 2. Remove the ICD 3 Test Interface Board and attach the modular cable between the debugger and target board. 3. Connect power to the target board. Header Target VDD (tVDD) is used to power the Input/Output drivers in MPLAB ICD 3 debugger AVDD** 4 Connect to Target Device Target Board Incorrect Target VDD (tVDD) VDD Target Application Device Modular Cable MPLAB ICD 3 Internal Circuitry (simplified) The Microchip name and logo, the Microchip logo, MPLAB and PIC are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. The MPLAB Certified logo and ICSP are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. © 2010 Microchip Technology Incorporated. Printed in the U.S.A. All Rights Reserved. 2/10 Target Board © 2010 Microchip Technology Inc., 3/10 DS51765C