AD AD7654

Dual 2-Channel Simultaneous Sampling
SAR 500 kSPS 16-Bit ADC
AD7654*
FEATURES
Dual 16-Bit 2-Channel Simultaneous Sampling ADC
16 Bits Resolution with No Missing Codes
Throughput:
500 kSPS (Normal Mode)
444 kSPS (Impulse Mode)
INL: ⴞ3.5 LSB Max (ⴞ0.0053% of Full Scale)
SNR: 89 dB Typ @ 100 kHz
THD: –100 dB @ 100 kHz
Analog Input Voltage Range: 0 V to 5 V
No Pipeline Delay
Parallel and Serial 5 V/3 V Interface
SPI™/QSPI™/MICROWIRE™/DSP Compatible
Single 5 V Supply Operation
Power Dissipation
120 mW Typical,
2.6 mW @ 10 kSPS
Package: 48-Lead Quad Flatpack (LQFP)
or 48-Lead Frame Chip Scale Package (LFCSP)
Low Cost
APPLICATIONS
AC Motor Control
3-Phase Power Control
4-Channel Data Acquisition
Uninterrupted Power Supplies
Communications
GENERAL DESCRIPTION
The AD7654 is a low cost, dual-channel, 16-bit, charge
redistribution SAR, analog-to-digital converter that operates
from a single 5 V power supply. It contains two low noise, wide
bandwidth track-and-hold amplifiers that allow simultaneous
sampling, a high speed 16-bit sampling ADC, an internal conversion clock, error correction circuits, and both serial and parallel
system interface ports. Each track-and-hold has a multiplexer in
front to provide a 4-channel input ADC.
The part features a very high sampling rate mode (Normal) and,
for low power applications, a reduced power mode (Impulse)
where the power is scaled with the throughput. It is available in
48-lead LQFP or 48-lead LFCSP packages with operation
specified from –40°C to +85°C.
PRODUCT HIGHLIGHTS
1. Simultaneous Sampling
The AD7654 features two sample-and-hold circuits that
allow simultaneous sampling. It provides 4-channel inputs.
*Patent pending
SPI and QSPI are trademarks of Motorola, Inc.
Microwire is a trademark of National Semiconductor Corporation.
FUNCTIONAL BLOCK DIAGRAM
AVDD AGND
DVDD
DGND
TRACK/HOLD
ⴛ2
INA1
INAN
REFGND REFx
OVDD
OGND
MUX
SERIAL
PORT
INA2
A0
SER/PAR
SWITCHED
CAP DAC
MUX
EOC
INB1
INBN
BUSY
MUX
16
INB2
PD
CLOCK AND
CONTROL LOGIC
PARALLEL
INTERFACE
D[15:0]
CS
RD
RESET
A/B
AD7654
BYTESWAP
IMPULSE
CNVST
PulSAR Selection
Type/kSPS
100–250
500–570
800–1000
Pseudo
Differential
AD7651
AD7660/
AD7661
AD7650/
AD7652
AD7664/
AD7666
AD7653
AD7667
True Bipolar
AD7663
AD7665
AD7671
True Differential
AD7675
AD7676
AD7677
18 Bit
AD7678
AD7679
AD7674
Multichannel/
Simultaneous
AD7654
2. Fast Throughput
The AD7654 is a very high speed (500 kSPS in Normal
Mode and 444 kSPS in Impulse Mode), charge redistribution,
16-bit SAR ADC that avoids pipeline delay.
3. Superior INL and No Missing Code
The AD7654 has a maximum integral nonlinearity of 3.5 LSB
with no missing codes at the 16-bit level.
4. Single-Supply Operation
The AD7654 operates from a single 5 V supply and dissipates
only 120 mW typical, even lower when a reduced throughput
is used with the reduced power mode (Impulse) and powerdown mode.
5. Serial or Parallel Interface
Versatile parallel or 2-wire serial interface arrangement is
compatible with both 3 V or 5 V logic.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2002
to +85C, V
otherwise noted.)
AD7654–SPECIFICATIONS (–40C
Parameter
Conditions
THROUGHPUT SPEED
Complete Cycle
Throughput Rate
Complete Cycle
Throughput Rate
DC ACCURACY
Integral Linearity Error
No Missing Codes
Transition Noise
Full-Scale Error2
Full-Scale Error Drift2
Unipolar Zero Error2
Unipolar Zero Error Drift2
Power Supply Sensitivity
AC ACCURACY
Signal-to-Noise
Spurious Free Dynamic Range
Total Harmonic Distortion
Signal-to-(Noise+Distortion)
Channel-to-Channel Isolation
–3 dB Input Bandwidth
Typ
Max
16
VINx – VINxN
VINxN
fIN = 100 kHz
500 kSPS Throughput
2 VREF
+0.5
55
45
See Analog Input Section
0
0
–3.5
16
0.7
± 0.25
±2
TMIN to TMAX
TMIN to TMAX
± 0.8
0.8
AVDD = 5 V ± 5%
fIN = 20 kHz
fIN = 100 kHz
fIN = 100 kHz
fIN = 100 kHz
fIN = 20 kHz
fIN = 100 kHz
fIN = 100 kHz, –60 dB Input
fIN = 100 kHz
Full-Scale Step
REFERENCE
External Reference Voltage Range
External Reference Current Drain
500 kSPS Throughput
88
87.5
DIGITAL INPUTS
Logic Levels
VIL
VIH
IIL
IIH
–0.3
+2.0
–1
–1
DIGITAL OUTPUTS
Data Format
Pipeline Delay
µs
kSPS
µs
kSPS
+3.5
LSB1
Bits
LSB
% of FSR
ppm/°C
% of FSR
ppm/°C
LSB
± 0.5
± 0.25
90
89
105
–100
90
88.5
30
–92
10
dB3
dB
dB
dB
dB
dB
dB
dB
MHz
2
30
5
ns
ps
ps rms
ns
2.5
180
AVDD/2
V
µA
+0.8
OVDD + 0.3
+1
+1
V
V
µA
µA
Parallel or Serial 16-Bit Straight Binary Coding
Conversion Results Available Immediately
after Completed Conversion
0.4
OVDD – 0.2
ISINK = 1.6 mA
ISOURCE = –500 µA
–2–
V
dB
µA
2
500
2.25
444
250
2.3
Unit
Bits
0
–0.1
In Normal Mode
In Normal Mode
In Impulse Mode
In Impulse Mode
SAMPLING DYNAMICS
Aperture Delay4
Aperture Delay Matching4
Aperture Jitter4
Transient Response
VOL
VOH
= 2.5 V, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless
Min
RESOLUTION
ANALOG INPUT
Voltage Range
Common-Mode Input Voltage
Analog Input CMRR
Input Current
Input Impedance
REF
V
V
REV. 0
AD7654
Parameter
Conditions
POWER SUPPLIES
Specified Performance
AVDD
DVDD
OVDD
Operating Current6
AVDD
DVDD
OVDD
Power Dissipation
Min
Typ
Max
Unit
4.75
4.75
2.25
5
5
5.25
5.25
5.255
V
V
V
500 kSPS Throughput
15.5
8.5
100
120
2.6
114
500 kSPS Throughput6
10 kSPS Throughput7
444 kSPS Throughput7
125
mA
mA
µA
mW
mW
mW
+85
°C
135
8
TEMPERATURE RANGE
Specified Performance
TMIN to TMAX
–40
NOTES
1
LSB means least significant bit. Within the 0 V to 5 V input range, one LSB is 76.294 µV.
2
See Definition of Specifications section. These specifications do not include the error contribution from the external reference.
3
All specifications in dB are referred to as full-scale input FS. Tested with an input signal at 0.5 dB below full scale unless otherwise specified.
4
Sample tested during initial release.
5
The maximum should be the minimum of 5.25 V and DVDD + 0.3 V.
6
In Normal Mode.
7
In Impulse Mode.
8
Contact factory for extended temperature range.
Specifications subject to change without notice.
TIMING SPECIFICATIONS
(–40C to +85C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted.)
Parameter
Refer to Figures 8 and 9
Convert Pulsewidth
Time between Conversions
(Normal Mode/Impulse Mode)
CNVST LOW to BUSY HIGH Delay
BUSY HIGH All Modes Except in Master Serial Read
after Convert Mode
(Normal Mode/Impulse Mode)
Aperture Delay
End of Conversions to BUSY LOW Delay
Conversion Time
(Normal Mode/Impulse Mode)
Acquisition Time
RESET Pulsewidth
CNVST LOW to EOC HIGH Delay
EOC HIGH for Channel A Conversion
(Normal Mode/Impulse Mode)
EOC LOW after Channel A Conversion
EOC HIGH for Channel B Conversion
Channel Selection Setup Time
Channel Selection Hold Time
Min
t1
5
t2
t3
2/2.25
t4
t5
t6
t7
t8
t9
t10
t11
t12
t13
t14
t15
Refer to Figures 10–14 (Parallel Interface Modes)
CNVST LOW to DATA Valid Delay
DATA Valid to BUSY LOW Delay
Bus Access Request to DATA Valid
Bus Relinquish Time
A/B LOW to Data Valid Delay
REV. 0
Symbol
t16
t17
t18
t19
t20
–3–
Typ
Max
ns
32
µs
ns
1.75/2
µs
ns
ns
1.75/2
µs
ns
ns
ns
2
10
250
10
30
1/1.25
45
0.75
250
30
1.75/2
14
5
Unit
40
15
40
µs
ns
µs
ns
ns
µs
ns
ns
ns
ns
AD7654
TIMING SPECIFICATIONS (continued)
Parameter
Symbol
Refer to Figures 15 and 16 (Master Serial Interface Modes)
CS LOW to SYNC Valid Delay
CS LOW to Internal SCLK Valid Delay
CS LOW to SDOUT Delay
CNVST LOW to SYNC Delay (Read during Convert)
(Normal Mode/Impulse Mode)
SYNC Asserted to SCLK First Edge Delay*
Internal SCLK Period*
Internal SCLK HIGH*
Internal SCLK LOW*
SDOUT Valid Setup Time*
SDOUT Valid Hold Time*
SCLK Last Edge to SYNC Delay*
CS HIGH to SYNC HI-Z
CS HIGH to Internal SCLK HI-Z
CS HIGH to SDOUT HI-Z
BUSY HIGH in Master Serial Read after Convert
(Normal Mode/Impulse Mode)
CNVST LOW to SYNC Asserted Delay
(Normal Mode/Impulse Mode)
SYNC Deasserted to BUSY LOW Delay
Min
Typ
t21
t22
t23
Unit
10
10
10
ns
ns
ns
250/500
t24
t25
t26
t27
t28
t29
t30
t31
t32
t33
t34
3
23
12
7
4
2
1
ns
ns
ns
ns
ns
ns
ns
40
10
10
10
ns
ns
ns
See Table I
t35
t36
t37
Refer to Figures 17 and 18 (Slave Serial Interface Modes)
External SCLK Setup Time
External SCLK Active Edge to SDOUT Delay
SDIN Setup Time
SDIN Hold Time
External SCLK Period
External SCLK HIGH
External SCLK LOW
Max
µs
ns
0.75/1
25
t38
t39
t40
t41
t42
t43
t44
5
3
5
5
25
10
10
ns
ns
ns
ns
ns
ns
ns
18
*In Serial Master Read during Convert Mode. See Table I for Serial Master Read after Convert Mode.
Specifications subject to change without notice.
Table I. Serial Clock Timings in Master Read after Convert
DIVSCLK[1]
DIVSCLK[0]
SYNC to SCLK First Edge Delay Minimum
Internal SCLK Period Minimum
Internal SCLK Period Typical
Internal SCLK HIGH Minimum
Internal SCLK LOW Minimum
SDOUT Valid Setup Time Minimum
SDOUT Valid Hold Time Minimum
SCLK Last Edge to SYNC Delay Minimum
Busy High Width Maximum (Normal)
Busy High Width Maximum (Impulse)
t25
t26
t26
t27
t28
t29
t30
t31
t35
t35
–4–
0
0
0
1
1
0
1
1
Unit
3
25
40
12
7
4
2
1
3.25
3.5
17
50
70
22
21
18
4
3
4.25
4.5
17
100
140
50
49
18
30
30
6.25
6.5
17
200
280
100
99
18
80
80
10.75
11
ns
ns
ns
ns
ns
ns
ns
ns
µs
µs
REV. 0
AD7654
ABSOLUTE MAXIMUM RATINGS 1
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature Range
(Soldering 10 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
Analog Input
INAx2, INBx2, REFx, INxN, REFGND . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . AGND – 0.3 V to AVDD + 0.3 V
Ground Voltage Differences
AGND, DGND, OGND . . . . . . . . . . . . . . . . . . . . . . ± 0.3 V
Supply Voltages
AVDD, DVDD, OVDD . . . . . . . . . . . . . . . . . –0.3 V to +7 V
AVDD to DVDD, AVDD to OVDD . . . . . . . . . . . . . . ± 7 V
DVDD to OVDD . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Digital Inputs . . . . . . . . . . . . . . . . . –0.3 V to DVDD + 0.3 V
Internal Power Dissipation3 . . . . . . . . . . . . . . . . . . . . . 700 mW
Internal Power Dissipation4 . . . . . . . . . . . . . . . . . . . . . . . 2.5 W
1.6mA
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
See Analog Input section.
3
Specification is for device in free air: 48-Lead LQFP: ␪JA = 91°C/W, ␪JC = 30°C/W.
4
Specification is for device in free air: 48-Lead LFCSP: ␪JA = 26°C/W.
IOL
2V
0.8V
tDELAY
TO OUTPUT
PIN
tDELAY
1.4V
CL
60pF*
2V
0.8V
500␮A
2V
0.8V
Figure 2. Voltage Reference Levels for Timing
IOH
*IN SERIAL INTERFACE MODES, THE SYNC, SCLK, AND
SDOUT TIMINGS ARE DEFINED WITH A MAXIMUM LOAD
CL OF 10pF; OTHERWISE, THE LOAD IS 60pF MAXIMUM.
Figure 1. Load Circuit for Digital Interface Timing,
SDOUT, SYNC, SCLK Outputs, CL = 10 pF
ORDERING GUIDE
Model
Temperature Range
Package Description
Package Option
AD7654AST
AD7654ASTRL
AD7654ACP
AD7654ACPRL
EVAL-AD7654CB1
EVAL-CONTROL BRD22
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Quad Flatpack (LQFP)
Quad Flatpack (LQFP)
Chip Scale Package (LFCSP)
Chip Scale Package (LFCSP)
Evaluation Board
Controller Board
ST-48
ST-48
CP-48
CP-48
NOTES
1
This board can be used as a standalone evaluation board or in conjunction with the EVAL-CONTROL BRD2 for evaluation/demonstration purposes.
2
This board allows a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
AD7654 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
REV. 0
–5–
AD7654
REF
REFGND
INB1
INBN
INB2
REFB
REFA
INA2
INAN
INA1
AGND
AGND
PIN CONFIGURATION
48 47 46 45 44 43 42 41 40 39 38 37
AGND
1
AVDD 2
PIN 1
IDENTIFIER
36
DVDD
35
A0 3
34
CNVST
PD
BYTESWAP 4
33
RESET
A/B 5
DGND 6
32
CS
31
RD
30
AD7654
TOP VIEW
(Not to Scale)
IMPULSE 7
SER/PAR 8
D0 9
29
EOC
BUSY
28
D15
D1 10
27
D14
D2/DIVSCLK[0] 11
26
D13
D3/DIVSCLK[1] 12
25
D12
D11/RDERROR
D10/SYNC
D9/SCLK
D8/SDOUT
DGND
DVDD
OVDD
OGND
D7/RDC/SDIN
D6/INVSCLK
D4/EXT/INT
D5/INVSYNC
13 14 15 16 17 18 19 20 21 22 23 24
PIN FUNCTION DESCRIPTIONS
Pin No.
Mnemonic
Type
Description
1, 47, 48
AGND
P
Analog Power Ground Pin
2
AVDD
P
Input Analog Power Pin. Nominally 5 V.
3
A0
DI
Multiplexer Select. When LOW, the analog inputs INA1 and INB1 are sampled simultaneously, then converted. When HIGH, the analog inputs INA2 and INB2 are sampled
simultaneously, then converted.
4
BYTESWAP
DI
Parallel Mode Selection (8 Bit, 16 Bit). When LOW, the LSB is output on D[7:0]
and the MSB is output on D[15:8]. When HIGH, the LSB is output on D[15:8] and
the MSB is output on D[7:0].
5
A/B
DI
Data Channel Selection. In parallel mode, when LOW, the data from channel B is
read. When HIGH, the data from channel A is read. In serial mode, when HIGH,
channel A is output first followed by channel B. When LOW, channel B is output
first followed by channel B.
6, 20
DGND
P
Digital Power Ground
7
IMPULSE
DI
Mode Selection. When HIGH, this input selects a reduced power mode. In this mode,
the power dissipation is approximately proportional to the sampling rate.
8
SER/PAR
DI
Serial/Parallel Selection Input. When LOW, the parallel port is selected; when HIGH, the
serial interface mode is selected and some bits of the DATA bus are used as a serial port.
9, 10
D[0:1]
DO
Bit 0 and Bit 1 of the Parallel Port Data Output Bus. When SER/PAR is HIGH, these
outputs are in high impedance.
11, 12
D[2:3] or
DI/O
When SER/PAR is LOW, these outputs are used as Bit 2 and Bit 3 of the Parallel Port
Data Output Bus.
DIVSCLK[0:1]
13
D[4]
or EXT/INT
When SER/PAR is HIGH, EXT/INT is LOW, and RDC/SDIN is LOW, which is the
serial master read after convert mode, these inputs, part of the serial port, are used to
slow down if desired the internal serial clock that clocks the data output. In the other
serial modes, these inputs are not used.
DI/O
When SER/PAR is LOW, this output is used as Bit 4 of the Parallel Port Data
Output Bus.
When SER/PAR is HIGH, this input, part of the serial port, is used as a digital select
input for choosing the internal or an external data clock, called respectively, Master
and Slave Mode. With EXT/INT tied LOW, the internal clock is selected on SCLK
output. With EXT/INT set to a logic HIGH, output data is synchronized to an external
clock signal connected to the SCLK input.
–6–
REV. 0
AD7654
Pin No.
Mnemonic
Type
Description
14
D[5]
DI/O
When SER/PAR is LOW, this output is used as Bit 5 of the Parallel Port Data
Output Bus.
or INVSYNC
15
D[6]
When SER/PAR is HIGH, this input, part of the serial port, is used to select the
active state of the SYNC signal. When LOW, SYNC is active HIGH. When HIGH,
SYNC is active LOW.
DI/O
or INVSCLK
16
D[7]
When SER/PAR is LOW, this output is used as Bit 6 of the Parallel Port Data
Output Bus.
When SER/PAR is HIGH, this input, part of the serial port, is used to invert the
SCLK signal. It is active in both Master and Slave modes.
DI/O
or RDC/SDIN
When SER/PAR is LOW, this output is used as Bit 7 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this input, part of the serial port, is used as either an external data input or a read mode selection input, depending on the state of EXT/INT.
When EXT/INT is HIGH, RDC/SDIN can be used as a data input to daisy-chain the
conversion results from two or more ADCs onto a single SDOUT line. The digital
data level on SDIN is output on SDOUT with a delay of 32 SCLK periods after the
initiation of the read sequence.
When EXT/INT is LOW, RDC/SDIN is used to select the read mode. When RDC/SDIN
is HIGH, the previous data is output on SDOUT during conversion. When RDC/SDIN is
LOW, the data can be output on SDOUT only when the conversion is complete.
17
OGND
P
Input/Output Interface Digital Power Ground
18
OVDD
P
Input/Output Interface Digital Power. Nominally at the same supply as the supply of
the host interface (5 V or 3 V).
19, 36
DVDD
P
Digital Power. Nominally at 5 V.
21
D[8]
DO
When SER/PAR is LOW, this output is used as Bit 8 of the Parallel Port Data
Output Bus.
or SDOUT
When SER/PAR is HIGH, this output, part of the serial port, is used as a serial data
output synchronized to SCLK. Conversion results are stored in a 32-bit on-chip register. The AD7654 provides the two conversion results, MSB first, from its internal shift
register. The order of channel outputs is controlled by A/B. In serial mode, when
EXT/INT is LOW, SDOUT is valid on both edges of SCLK.
In Serial Mode, when EXT/INT is HIGH:
If INVSCLK is LOW, SDOUT is updated on the SCLK rising edge and valid on the
next falling edge.
If INVSCLK is HIGH, SDOUT is updated on the SCLK falling edge and valid on
the next rising edge.
22
D[9]
DI/O
or SCLK
23
D[10]
or SYNC
When SER/PAR is LOW, this output is used as Bit 9 of the Parallel Port Data
Output Bus.
When SER/PAR is HIGH, this pin, part of the serial port, is used as a serial data clock
input or output, dependent upon the logic state of the EXT/INT pin. The active edge
where the data SDOUT is updated depends on the logic state of the INVSCLK pin.
DO
When SER/PAR is LOW, this output is used as Bit 10 of the Parallel Port Data
Output Bus.
When SER/PAR is HIGH, this output, part of the serial port, is used as a digital output
frame synchronization for use with the internal data clock (EXT/INT = Logic LOW).
When a read sequence is initiated and INVSYNC is LOW, SYNC is driven HIGH
and frames SDOUT. After the first channel is output, SYNC is pulsed LOW. When
a read sequence is initiated and INVSYNC is HIGH, SYNC is driven LOW and
remains LOW while SDOUT output is valid. After the first channel is output, SYNC
is pulsed HIGH.
REV. 0
–7–
AD7654
PIN FUNCTION DESCRIPTIONS (continued)
Pin No.
Mnemonic
Type
Description
24
D[11]
DO
When SER/PAR is LOW, this output is used as Bit 11 of the Parallel Port Data
Output Bus.
or RDERROR
When SER/PAR is HIGH and EXT/INT is HIGH, this output, part of the serial
port, is used as an incomplete read error flag. In Slave mode, when a data read is
started and not complete when the following conversion is complete, the current data
is lost and RDERROR is pulsed high.
25–28
D[12:15]
DO
Bit 12 to Bit 15 of the Parallel Port Data Output Bus. When SER/PAR is HIGH,
these outputs are in high impedance.
29
BUSY
DO
Busy Output. Transitions HIGH when a conversion is started and remains HIGH
until the two conversions are complete and the data are latched into the on-chip shift
register. The falling edge of BUSY can be used as a data ready clock signal.
30
EOC
DO
End of Convert Output. Goes LOW at each channel conversion.
31
RD
DI
Read Data. When CS and RD are both LOW, the interface parallel or serial output
bus is enabled.
32
CS
DI
Chip Select. When CS and RD are both LOW, the interface parallel or serial output
bus is enabled. CS is also used to gate the external serial clock.
33
RESET
DI
Reset Input. When set to a logic HIGH, reset the AD7654. Current conversion if any
is aborted. If not used, this pin could be tied to DGND.
34
PD
DI
Power-Down Input. When set to a logic HIGH, power consumption is reduced and
conversions are inhibited after the current one is completed.
35
CNVST
DI
Start Conversion. A falling edge on CNVST puts the internal sample-and-hold into the
hold state and initiates a conversion. In Impulse Mode (IMPULSE HIGH), if
CNVST is held low when the acquisition phase (t8) is complete, the internal sampleand-hold is put into the hold state and a conversion is immediately started.
37
REF
AI
This input pin is used to provide a reference to the converter.
38
REFGND
AI
Reference Input Analog Ground
39, 41
INB1, INB2
AI
Analog Inputs
40, 45
INBN, INAN
AI
Analog Inputs Ground Senses. Allow to sense each channel ground independently.
42, 43
REFB, REFA
AI
These inputs are the references applied to channel A and channel B, respectively.
44, 46
INA2, INA1
NOTES
AI = Analog Input
DI = Digital Input
DI/O = Bidirectional Digital
DO = Digital Output
P = Power
–8–
REV. 0
AD7654
DEFINITION OF SPECIFICATIONS
Integral Nonlinearity Error (INL)
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to S/(N+D) by the following formula:
Linearity error refers to the deviation of each individual code from
a line drawn from negative full scale through positive full scale.
The point used as negative full scale occurs 1/2 LSB before the first
code transition. Positive full scale is defined as a level 1 1/2 LSB
beyond the last code transition. The deviation is measured from
the middle of each code to the true straight line.
(
and is expressed in bits.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic components to the rms value of a full-scale input signal and is
expressed in decibels.
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It
is often specified in terms of resolution for which no missing
codes are guaranteed.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
Full-Scale Error
The last transition (from 111 . . . 10 to 111 . . . 11) should
occur for an analog voltage 1 1/2 LSB below the nominal full
scale (4.999886 V for the 0 V to 5 V range). The full-scale error
is the deviation of the actual level of the last transition from the
ideal level.
Signal-to-(Noise+Distortion) Ratio (S/[N+D])
S/(N+D) is the ratio of the rms value of the actual input signal
to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc. The
value for S/(N+D) is expressed in decibels.
Unipolar Zero Error
In unipolar mode, the first transition should occur at a level
1/2 LSB above analog ground. The unipolar zero error is the
deviation of the actual transition from that point.
Aperture Delay
Aperture delay is a measure of the acquisition performance and
is measured from the falling edge of the CNVST input to when
the input signals are held for a conversion.
Spurious-Free Dynamic Range (SFDR)
The difference, in decibels, between the rms amplitude of the
input signal and the peak spurious signal.
REV. 0
)
ENOB = S [ N + D ]dB − 1.76) 6.02
Transient Response
The time required for the AD7654 to achieve its rated accuracy
after a full-scale step function is applied to its input.
–9–
AD7654–Typical Performance Characteristics
3
5
4
2
3
1
1
DNL – LSD
INL – LSB
2
0
–1
0
–1
–2
–3
–2
–4
–5
–3
0
16384
32768
CODE
65535
49152
TPC 1. Integral Nonlinearity vs. Code
0
16384
32768
CODE
49152
65535
TPC 4. Differential Nonlinearity vs. Code
10000
8000
9366
7288 7220
9000
7000
8000
6000
7000
COUNTS
4000
3000
6000
5000
4000
3411
3299
3000
2000
2000
953
1000
903
1000
0
0
14
6
0
0
0
7FBF 7FC0 7FC1 7FC2 7FC3 7FC4 7FC5 7FC6 7FC7 7FC8
CODE IN HEXA
TPC 2. Histogram of 16,384 Conversions of a DC
Input at the Code Transition
0
176
0
132
0
0
7FBF 7FC0 7FC1 7FC2 7FC3 7FC4 7FC5 7FC6 7FC7
CODE IN HEXA
TPC 5. Histogram of 16,384 Conversions of a DC
Input at the Code Center
5
96
–98
93
–100
8192 POINT FFT
fS = 500kHz
4
fIN = 100kHz, –0.5dB
SNR = 89.9dB
S/[N+D] = 89.4dB
THD = –99.3dB
SFDR = 101.6dB
3
2
THD
SNR – dB
1
0
–1
–102
90
SNR
THD – dB
0
AMPLITUDE – dB of Full Scale
COUNTS
5000
–2
–104
87
–3
–4
–5
0
25
50
75
100
125
150
175
200
225
84
–55
250
FREQUENCY – kHz
TPC 3. FFT Plot
–35
–15
5
25
45
65
TEMPERATURE – ⴗC
85
105
–106
125
TPC 6. SNR, THD vs. Temperature
–10–
REV. 0
AD7654
100
16.0
95
15.5
10
6
SNR
S/[N+D]
85
14.5
ENOB
80
14.0
75
13.5
FULL-SCALE ERROR
4
15.0
2
LSB
90
ENOB – Bits
SNR AND S/[N+D] – dB
8
0
–2
ZERO ERROR
–4
–6
–8
70
1
13.0
1000
10
100
FREQUENCY – kHz
–10
–55
TPC 7. SNR, S/(N+D), and ENOB vs. Frequency
65
5
25
45
TEMPERATURE – ⴗC
–15
85
105
125
TPC 10. Full-Scale and Zero Error vs. Temperature
100
92
NORMAL AVDD
10
OPERATING CURRENCY – mA
SNR (REFERRED TO FULL SCALE – dB
–35
SNR
90
S/[N+D]
88
NORMAL DVDD
1
IMPULSE AVDD
0.1
IMPULSE DVDD
0.01
0.001
OVDD 2.7V
86
–60
–50
–40
–30
–20
INPUT LEVEL – dB
–10
0
115
–65
110
50
SNR (REFERRED TO FULL SCALE – dB
–60
SFDR
–70
105
–75
100
–80
95
–85
90
CROSSTALK B TO A
85
–95
CROSSTALK A TO B
–100
THD
80
THIRD
HARMONIC
75
70
–105
SECOND
HARMONIC
–110
–115
1
10
100
FREQUENCY – kHz
65
60
1000
OVDD = 2.7V @85ⴗC
40
OVDD = 2.7V @25ⴗC
OVDD = 5V @85ⴗC
30
OVDD = 5V @25ⴗC
20
10
0
TPC 9. THD, Harmonics, Crosstalk, and SFDR vs.
Frequency
REV. 0
1000
TPC 11. Operating Currents vs. Sample Rate
SFDR – dB
THD, HARMONICS, CROSSTALK – dB
TPC 8. SNR and S/(N+D) vs. Input Level (Referred
to Full Scale)
–90
100
10
SAMPLING RATE – kSPS
1
0
50
100
CL – pF
150
200
TPC 12. Typical Delay vs. Load Capacitance CL
–11–
AD7654
CIRCUIT INFORMATION
Table I. Output Codes and Ideal Input Voltages
The AD7654 is a very fast, low power, single-supply, precise
simultaneous sampling 16-bit analog-to-digital converter (ADC).
The AD7654 provides the user with two on-chip track-and-hold,
successive approximation ADCs that do not exhibit any pipeline
or latency, making it ideal for multiple multiplexed channel
applications. The AD7654 can be also used as a 4-channel ADC
with two pairs simultaneously sampled.
The AD7654 can be operated from a single 5 V supply and be
interfaced to either 5 V or 3 V digital logic. It is housed in
48-lead LQFP or tiny 48-lead LFCSP packages that combine
space savings and allow flexible configurations as either a serial
or parallel interface. The AD7654 is pin-to-pin-compatible with
PulSAR ADCs.
Modes of Operation
Description
Analog
Input VREF = 2.5 V
Digital Output
Code (Hexa)
FSR –1 LSB
FSR – 2 LSB
Midscale + 1 LSB
Midscale
Midscale – 1 LSB
–FSR + 1 LSB
–FSR
4.999924 V
4.999847 V
2.500076 V
2.5 V
2.499924 V
–76.29 µV
0V
FFFF1
FFFE
8001
8000
7FFF
0001
00002
NOTES
1
This is also the code for overrange analog input (V INx – VINxN above 2 × (VREF –
VREFGND)).
2
This is also the code for underrange analog input (V INx below VINxN).
TYPICAL CONNECTION DIAGRAM
The AD7654 features two modes of operation, Normal and
Impulse. Each of these modes is more suitable for specific
applications.
The Normal Mode is the fastest mode (500 kSPS). Except when it
is powered down (PD HIGH), the power dissipation is almost
independent of the sampling rate.
Figure 5 shows a typical connection diagram for the AD7654.
Different circuitry shown on this diagram is optional and is
discussed below.
Analog Inputs
Figure 4 shows a simplified analog input section of the AD7654.
The Impulse Mode, the lowest power dissipation mode, allows
power saving between conversions. The maximum throughput
in this mode is 444 kSPS. When operating at 10 kSPS, for
example, it typically consumes only 2.6 mW. This feature makes
the AD7654 ideal for battery-powered applications.
AVDD
RA = 500
INAx
CS
Transfer Functions
CS
The AD7654 data format is straight binary. The ideal transfer
characteristic for the AD7654 is shown in Figure 3 and Table I.
INBx
RB = 500
ADC CODE – Straight Binary
AGND
Figure 4. Simplified Analog Input
111...111
111...110
111...101
The diodes shown in Figure 4 provide ESD protection for the
inputs. Care must be taken to ensure that the analog input
signal never exceeds the absolute ratings on these inputs. This
will cause these diodes to become forward-biased and start
conducting current. These diodes can handle a forward-biased
current of 120 mA maximum. This condition could eventually
occur when the input buffer’s (U1) or (U2) supplies are different
from AVDD. In such case, an input buffer with a short-circuit
current limitation can be used to protect the part.
000...010
000...001
000...000
–FS
–FS+1 LSB
–FS+0.5 LSB
+FS–1 LSB
+FS–1.5 LSB
ANALOG INPUT
Figure 3. ADC Ideal Transfer Function
This analog input structure allows the sampling of the differential
signal between INx and INxN. Unlike other converters, the
INxN is sampled at the same time as the INx input. By using
these differential inputs, small signals common to both inputs
are rejected.
–12–
REV. 0
AD7654
DVDD
ANALOG
SUPPLY
(5V)
30
+
NOTE 6
100nF
10F
AD780
AVDD
2.5V REF
REF A/
REF B/
REF
1M
C
50k + REF
NOTE 1
100nF
1F
DIGITAL SUPPLY
(3.3V OR 5V)
+
10F
AGND
100nF
DGND
DVDD
100nF
OVDD
+
10F
OGND
SERIAL PORT
SCLK
SDOUT
NOTE 2
REFGND
NOTE 3
50
NOTE 4
ANALOG INPUT A
BUSY
–
U1
+
AD8021
15
CC
CNVST
INAx
C/P/DSP
50
D
NOTE 7
2.7nF
AD7654
NOTE 5
INAN
SER/PAR
DVDD
A/B
50
A0
NOTE 4
ANALOG INPUT B
–
U2
+
AD8021
15
CC
CS
INBx
CLOCK
RD
BYTESWAP
2.7nF
RESET
NOTE 5
PD
INBN
NOTES
1. SEE VOLTAGE REFERENCE INPUT SECTION.
2. WITH THE RECOMMENDED VOLTAGE REFERENCES, CREF IS 47F. SEE VOLTAGE REFERENCE INPUT SECTION.
3. OPTIONAL CIRCUITRY FOR HARDWARE GAIN CALIBRATION.
4. THE AD8021 IS RECOMMENDED. SEE DRIVER AMPLIFIER CHOICE SECTION.
5. SEE ANALOG INPUT SECTION.
6. OPTION, SEE POWER SUPPLY SECTION.
7. OPTIONAL LOW JITTER CNVST. SEE CONVERSION CONTROL SECTION.
Figure 5. Typical Connection Diagram (Serial Interface)
During the acquisition phase, for ac signals, the AD7654 behaves
like a one-pole RC filter consisted of the equivalent resistance
RA, RB, and CS. The resistors RA and RB are typically 500 Ω and
are a lumped component made up of some serial resistor and the
on resistance of the switches. The capacitor CS is typically 32 pF
and is mainly the ADC sampling capacitor. This one-pole filter with
a typical –3 dB cutoff frequency of 10 MHz reduces undesirable
aliasing effect and limits the noise coming from the inputs.
depends on the amount of total harmonic distortion (THD)
that can be tolerated. The THD degrades with increase of the
source impedance.
Driver Amplifier Choice
Although the AD7654 is easy to drive, the driver amplifier
needs to meet at least the following requirements:
Because the input impedance of the AD7654 is very high, the
AD7654 can be driven directly by a low impedance source
without gain error. As shown in Figure 5 that allows the user
to put an external one-pole RC filter between the output of
the amplifier output and the ADC analog inputs to even
further improve the noise filtering done by the AD7654 analog input circuit. However, the source impedance has to be
kept low because it affects the ac performance, especially the
total harmonic distortion. The maximum source impedance
REV. 0
–13–
• The driver amplifier and the AD7654 analog input circuit
together have to be able to settle for a full-scale step of the
capacitor array at a 16-bit level (0.0015%). In the amplifier’s
data sheet, the settling at 0.1% or 0.01% is more commonly
specified. It could significantly differ from the settling time
at a 16-bit level and, therefore, it should be verified prior to
the driver selection. The tiny op amp AD8021, which combines ultralow noise and a high gain bandwidth, meets this
settling time requirement even when used with a high gain
of up to 13.
AD7654
• The noise generated by the driver amplifier needs to be kept
as low as possible to preserve the SNR and transition noise
performance of the AD7654. The noise coming from the
driver is filtered by the AD7654 analog input circuit one-pole
low-pass filter made by RA, RB, and CS. The SNR degradation due to the amplifier is:
SNRLOSS


56
= 20 log 
π
2

 562 + f –3 dB ( N eN )

2
Care should be taken with the reference temperature coefficient
of the voltage reference, which directly affects the full-scale
accuracy if this parameter is applicable. For instance, a
± 15 ppm/°C tempco of the reference changes the full-scale
accuracy by ± 1 LSB/°C.
Power Supply
The AD7654 uses three sets of power supply pins: an analog 5 V
supply AVDD, a digital 5 V core supply DVDD, and a digital
input/output interface supply OVDD. The OVDD supply
allows direct interface with any logic working between 2.7 V and
DVDD + 0.3 V. To reduce the number of supplies needed, the
digital core (DVDD) can be supplied through a simple RC filter
from the analog supply, as shown in Figure 5. The AD7654 is
independent of power supply sequencing, once OVDD does not
exceed DVDD by more than 0.3 V, and thus free from supply
voltage induced latchup. Additionally, it is very insensitive to
power supply variations over a wide frequency range, as shown
in Figure 6.






where:
f–3 dB is the –3 dB input bandwidth in MHz of the AD7654
(10 MHz) or the cutoff frequency of the input filter if any is
used.
N is the noise factor of the amplifier (1 if in buffer configuration).
eN is the equivalent input noise voltage of the op amp in
nV/√Hz1/2.
70
For instance, a driver with an equivalent input noise of
2 nV/√Hz like the AD8021 and configured as a buffer, thus
with a noise gain of +1, will degrade the SNR by only 0.03 dB
with the filter in Figure 5, and 0.09 dB without.
65
PSRR – dB
60
• The driver needs to have a THD performance suitable to
that of the AD7654.
55
The AD8021 meets these requirements and is usually appropriate for almost all applications. The AD8021 needs an external
compensation capacitor of 10 pF. This capacitor should have
good linearity as an NPO ceramic or mica type.
50
The AD8022 could be used where a dual version is needed and
a gain of 1 is used.
40
45
1
10
100
1000
10000
FREQUENCY – kHz
The AD829 is another alternative where high frequency (above
100 kHz) performance is not required. In a gain of 1, it requires
an 82 pF compensation capacitor.
The AD8610 is another option where low bias current is needed
in low frequency applications.
Voltage Reference Input
The AD7654 requires an external 2.5 V reference. The reference
input should be applied to REFA and REFB. The voltage reference input REF of the AD7654 has a dynamic input impedance;
it should therefore be driven by a low impedance source with an
efficient decoupling. This decoupling depends on the choice of
the voltage reference but usually consists of a 1 µF ceramic
capacitor and a low ESR tantalum capacitor connected to the
REFA, REFB, and REFGND inputs with minimum parasitic
inductance. 47 µF is an appropriate value for the tantalum
capacitor when using one of the recommended reference voltages:
Figure 6. PSRR vs. Frequency
POWER DISSIPATION
In Impulse Mode, the AD7654 automatically reduces its power
consumption at the end of each conversion phase. During the
acquisition phase, the operating currents are very low, which
allows significant power savings when the conversion rate is
reduced, as shown in Figure 7. This feature makes the AD7654
ideal for very low power battery applications.
It should be noted that the digital interface remains active even
during the acquisition phase. To reduce the operating digital
supply currents even further, the digital inputs need to be driven
close to the power rails (i.e., DVDD and DGND), and OVDD
should not exceed DVDD by more than 0.3 V.
• The low noise, low temperature drift AD780 voltage
reference
• The low cost AD1582 voltage reference
For applications using multiple AD7654s, it is more effective to
buffer the reference voltage using the internal buffer. Each ADC
should be decoupled individually.
–14–
REV. 0
AD7654
POWER DISSIPATION – mW
1000
conversion process running by itself. It should be noted that the
analog input has to be settled when BUSY goes low. Also, at
power-up, CNVST should be brought low once to initiate the
conversion process. In this mode, the AD7654 could sometimes
run slightly faster than the guaranteed limits in the Impulse
mode of 444 kSPS. This feature does not exist in Normal mode.
NORMAL
100
IMPULSE
10
Although CNVST is a digital signal, it should be designed with
special care with fast, clean edges and levels, and with minimum
overshoot and undershoot or ringing.
For applications where the SNR is critical, the CNVST signal
should have very low jitter. Some solutions to achieve this are to
use a dedicated oscillator for CNVST generation or, at least, to
clock it with a high frequency low jitter clock, as shown in Figure 5.
1
0.1
100
10
SAMPLING RATE – kSPS
1
1000
t9
Figure 7. Power Dissipation vs. Sample Rate
RESET
CONVERSION CONTROL
Figure 8 shows the detailed timing diagrams of the conversion
process. The AD7654 is controlled by the signal CNVST, which
initiates conversion. Once initiated, it cannot be restarted or
aborted, even by the power-down input PD, until the conversion is complete. The CNVST signal operates independently of
the CS and RD signals. The A0 signal is the MUX select signal that chooses which input signal will be sampled. When
high, INx1 is chosen and when low, INx2 is chosen, where x is
either A or B. It should be noted that this signal should not be
changed during the acquisition phase of the converter.
BUSY
DATA BUS
t8
CNVST
Figure 9. Reset Timing
t2
t1
DIGITAL INTERFACE
CNVST
t 14
The AD7654 has a versatile digital interface; it can be interfaced
with the host system by using either a serial or parallel interface.
The serial interface is multiplexed on the parallel data bus. The
AD7654 digital interface accommodates either 3 V or 5 V logic
by simply connecting the OVDD supply pin of the AD7654 to the
host system interface digital supply.
t 15
A0
t3
BUSY
t4
t 10
EOC
t5
MODE
ACQUIRE
t 13
t 11
t 12
t6
CONVERT B
CONVERT A
t7
ACQUIRE
CONVERT
t8
Signals CS and RD control the interface. When at least one of
these signals is high, the interface outputs are in high impedance.
Usually, CS allows the selection of each AD7654 in multicircuit
applications and is held low in a single AD7654 design. RD is
generally used to enable the conversion result on the data bus.
In parallel mode, signal A/B allows the choice of reading either
the output of channel A or channel B, whereas in serial mode,
signal A/B controls which channel is output first.
Figure 8. Conversion Control
In Impulse mode, conversions can be automatically initiated. If
CNVST is held low when BUSY is low, the AD7654 controls
the acquisition phase and automatically initiates a new conversion. By keeping CNVST low, the AD7654 keeps the
REV. 0
–15–
AD7654
CS = RD = 0
that it is read only during the first half of the conversion
phase. This avoids any potential feedthrough between voltage
transients on the digital interface and the most critical analog
conversion circuitry.
t1
CNVST
t 16
The BYTESWAP pin allows a glueless interface to an 8-bit bus.
As shown in Figure 13, the LSB byte is output on D[7:0] and
the MSB is output on D[15:8] when BYTESWAP is low. When
BYTESWAP is high, the LSB and MSB bytes are swapped, the
LSB is output on D[15:8], and the MSB is output on D[7:0].
By connecting BYTESWAP to an address line, the 16-bit data
can be read in two bytes on either D[15:8] or D[7:0].
BUSY
t4
t3
t 17
EOC t 10
DATA BUS
PREVIOUS CHANNEL A
OR B
PREVIOUS CHANNEL B
OR NEW A
NEW A
OR B
Figure 10. Master Parallel Data Timing for Reading (Continuous Read)
CS
RD
CS
BYTE
RD
PINS D[15:8]
HI-Z
HIGH BYTE
LOW BYTE
HI-Z
BUSY
t18
CURRENT
CONVERSION
DATA BUS
t18
PINS D[7:0]
t19
t19
HI-Z
RD
t1
t 12
t 10
A/B
t 13
t 11
DATA BUS
BUSY
HI-Z
CHANNEL A
t18
t4
t3
CHANNEL B
HI-Z
t20
Figure 14. A/B Channel Reading
PREVIOUS
CONVERSION
DATA BUS
HIGH BYTE
CS
CS = 0
EOC
t18
LOW BYTE
Figure 13. 8-Bit Parallel Interface
Figure 11. Slave Parallel Data Timing for Reading
(Read after Convert)
CNVST, RD
HI-Z
t 18
The detailed functionality of A/B is explained in Figure 15.
When high, the data from channel A is available on the data bus.
When low, the data bus now carries output from channel B.
Note that channel A can be read immediately after conversion is
done (EOC), while channel B is still in its converting phase.
t 19
Figure 12. Slave Parallel Data Timing for Reading
(Read during Convert)
PARALLEL INTERFACE
SERIAL INTERFACE
The AD7654 is configured to use the parallel interface (Figure 10)
when the SER/PAR is held low. The data can be read either
after each conversion, which is during the next acquisition phase
or during the other channel’s conversion, or during the following
conversion as shown, respectively, in Figures 11 and 12. When the
data is read during the conversion, however, it is recommended
The AD7654 is configured to use the serial interface when the
SER/PAR is held high. The AD7654 outputs 32 bits of data,
MSB first, on the SDOUT pin. The order of the channels being
output is controlled by A/B. When high, channel A is output
first; when low, channel B is output first. Unlike in parallel
–16–
REV. 0
AD7654
mode, channel A data is updated only after channel B conversion. This data is synchronized with the 32 clock pulses provided
on the SCLK pin.
between digital activity and the critical conversion decisions.
The SYNC signal goes low after the LSB of each channel has
been output.
MASTER SERIAL INTERFACE
Internal Clock
SLAVE SERIAL INTERFACE
External Clock
The AD7654 is configured to generate and provide the serial
data clock SCLK when the EXT/INT pin is held low. The
AD7654 also generates a SYNC signal to indicate to the host
when the serial data is valid. The serial clock SCLK and the
SYNC signal can be inverted if desired. The output data is valid
on both the rising and falling edge of the data clock. Depending
on RDC/SDIN input, the data can be read after each conversion or during the following conversion.
The AD7654 is configured to accept an externally supplied serial
data clock on the SCLK pin when the EXT/INT pin is held
high. In this mode, several methods can be used to read the
data. The external serial clock is gated by CS and the data are
output when both CS and RD are low. Thus, depending on CS,
the data can be read after each conversion or during the following conversion. The external clock can be either a continuous or
discontinuous clock. A discontinuous clock can be either normally
high or normally low when inactive. Figures 17 and 18 show the
detailed timing diagrams of these methods.
Figures 15 and 16 show the detailed timing diagrams of these
two modes.
Usually, because the AD7654 is used with a fast throughput,
the mode Master Read during Conversion is the most recommended serial mode when it can be used.
In Read-after-Conversion Mode, it should be noted that unlike
in other modes, the signal BUSY returns low after the 32 data
bits are pulsed out and not at the end of the conversion phase,
which results in a longer BUSY width. One advantage of this
mode is that it can accommodate slow digital hosts because the
serial clock can be slowed down by using DIVSCLK.
In Read-during-Conversion Mode, the serial clock and data toggle
at appropriate instants, which minimizes potential feedthrough
RDC/SDIN = 0
EXT/INT = 0
CS, RD
While the AD7654 is performing a bit decision, it is important
that voltage transients not occur on digital input/output pins or
degradation of the conversion result could occur. This is particularly important during the second half of the conversion
phase of each channel because the AD7654 provides error correction circuitry that can correct for an improper bit decision
made during the first half of the conversion phase. For this
reason, it is recommended that when an external clock is provided, it is a discontinuous clock that is toggling only when
BUSY is low or, more importantly, that it does not transition
during the latter half of EOC high.
INVSCLK = INVSYNC = 0
A/B = 1
t3
CNVST
t35
BUSY
EOC
t12
t13
t37
t36
t32
SYNC
t25
t26
t21
t27
SCLK
t31
t28
1
2
CH A
D15
CH A
D14
16
17
t33
30
31
CH B
D2
CH B
D1
32
t22
t34
X
SDOUT
t23
t29
CH B D0
t30
Figure 15. Master Serial Data Timing for Reading (Read after Convert)
REV. 0
–17–
AD7654
EXT/INT = 0
CS, RD
INVSCLK = INVSYNC = 0
RDC/SDIN = 1
A/B = 1
t1
CNVST
t3
BUSY
t 12
EOC
t 10
t 13
t 11
t 24
t 32
SYNC
t 21
t 26
t 27 t 28
SCLK
t 31
t 33
t 22
1
2
CH A
D15
CH A
D14
1
2
CH B
D15
CH B
D14
16
16
t 25
t 34
SDOUT
X
t 23
CH A D0
CH B D0
t 30
t 29
Figure 16. Master Serial Data Timing for Reading (Read Previous Conversion during Convert)
RD = 0
INVSCLK = 0
EXT/INT = 1
A/B = 1
CS
EOC
BUSY
t 42
t 43 t 44
1
SCLK
2
t 38
3
30
31
32
33
34
t 39
X
SDOUT
t 23
CH A
D15
CH A
D14
CH A
D13
CH B D1
CH B D0
X CH A
D15
X CH A
D14
X CH A
D14
X CH A
D13
X CH B
D1
X CH B
D0
Y CH A
D15
Y CH A
D14
t 41
X CH A
D15
SDIN
t 40
Figure 17. Slave Serial Data Timing for Reading (Read after Convert)
–18–
REV. 0
AD7654
RD = 0
INVSCLK = 0
EXT/INT = 1
A/B = 1
CS
t 10
CNVST
t 12
t 13
t 11
EOC
BUSY
t3
t 42
t 43 t 44
SCLK
1
t 38
3
31
32
t 39
X
SDOUT
2
CH A D15 CH A D14 CH A D13
CH B D1
CH B D0
t 23
Figure 18. Slave Serial Data Timing for Reading (Read Previous Conversion during Convert)
External Discontinuous Clock Data Read after Conversion
External Clock Data Read during Conversion
This mode is the most recommended of the serial slave modes.
Figure 18 shows the detailed timing diagrams of this method.
After a conversion is complete, indicated by BUSY returning
low, the results of this conversion can be read while both CS
and RD are low. The data from both channels are shifted out,
MSB first, with 32 clock pulses, and is valid on both rising and
falling edge of the clock.
Figure 18 shows the detailed timing diagrams of this method.
During a conversion, while both CS and RD are low, the result
of the previous conversion can be read. The data is shifted out,
MSB first, with 32 clock pulses, and is valid on both rising and
falling edges of the clock. The 32 bits have to be read before the
current conversion is complete. If that is not done, RDERROR
is pulsed high and can be used to interrupt the host interface to
prevent incomplete data reading. There is no daisy-chain feature in this mode, and RDC/SDIN input should always be tied
either high or low.
One advantage of this method is that the conversion performance is not degraded because there are no voltage transients on
the digital interface during the conversion process.
Another advantage is to be able to read the data at any speed up
to 40 MHz, which accommodates both slow digital host interface
and the fastest serial reading.
Finally, in this mode only, the AD7654 provides a daisy-chain
feature using the RDC/SDIN input pin for cascading multiple
converters together. This feature is useful for reducing component
count and wiring connections when it is desired, as it is for
instance, in isolated multiconverters applications.
To reduce performance degradation due to digital activity, a fast
discontinuous clock is recommended to ensure that all the bits
are read during the first half of the conversion phase. It is also
possible to begin to read the data after conversion and continue
to read the last bits even after a new conversion has been initiated.
An example of the concatenation of two devices is shown in
Figure 19. Simultaneous sampling is possible by using a common
CNVST signal. It should be noted that the RDC/SDIN input is
latched on the edge of SCLK opposite the one used to shift out
the data on SDOUT. Therefore, the MSB of the upstream
converter follows the LSB of the downstream converter on the
next SCLK cycle.
REV. 0
–19–
AD7654
ground planes that can be easily separated. Digital and analog
ground planes should be joined in only one place, preferably
underneath the AD7654, or, at least as close as possible to the
AD7654. If the AD7654 is in a system where multiple devices
require analog-to-digital ground connections, the connection
should still be made at one point only, a star ground point
that should be established as close as possible to the AD7654.
BUSY
OUT
BUSY
BUSY
AD7654
AD7654
#2 (UPSTREAM)
#1 (DOWNSTREAM)
RDC/SDIN
SDOUT
RDC/SDIN
SDOUT
CNVST
DATA
OUT
CNVST
CS
CS
SCLK
SCLK
SCLK IN
CS IN
CNVST IN
Figure 19. Two AD7654s in a Daisy-Chain Configuration
MICROPROCESSOR INTERFACING
The AD7654 is ideally suited for traditional dc measurement
applications supporting a microprocessor, and for ac signal
processing applications interfacing to a digital signal processor.
The AD7654 is designed to interface with either a parallel 8-bit
or 16-bit wide interface, a general-purpose serial port, or I/O
ports on a microcontroller. A variety of external buffers can be
used with the AD7654 to prevent digital noise from coupling into
the ADC. The following section illustrates the use of the AD7654
with an SPI-equipped DSP, the ADSP-219x.
SPI Interface (ADSP-219x)
Figure 19 shows an interface diagram between the AD7654 and
an SPI-equipped DSP, ADSP-219x. To accommodate the slower
speed of the DSP, the AD7654 acts as a slave device and data
must be read after conversion. This mode also allows the daisychain feature. The convert command can be initiated in response
to an internal timer interrupt. The 32-bit output data are read
with two SPI 16-bit wide access. The reading process could
be initiated in response to the end-of-conversion signal (BUSY
going low) using an interrupt line of the DSP. The Serial Peripheral
Interface (SPI) on the ADSP-219x is configured for master mode
(MSTR) = 1, Clock Polarity Bit (CPOL) = 0, and Clock Phase Bit
(CPHA) = 1 by writing to the SPI Control Register (SPICLTx).
DVDD
AD7654*
ADSP-219x*
SER/PAR
EXT/INT
BUSY
CS
SDOUT
RD
SCLK
INVSCLK
CNVST
PFx
SPIxSEL (PFx)
MISOx
SCKx
PFx or TFSx
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 20. Interfacing the AD7654 to SPI Interface
It is recommended to avoid running digital lines under the
device as these will couple noise onto the die. The analog
ground plane should be allowed to run under the AD7654 to
avoid noise coupling. Fast switching signals like CNVST or
clocks should be shielded with digital ground to avoid radiating
noise to other sections of the board, and should never run near
analog signal paths. Crossover of digital and analog signals
should be avoided. Traces on different but close layers of the
board should run at right angles to each other. This will reduce
the effect of feedthrough through the board. The power supply
lines to the AD7654 should use as large a trace as possible to
provide low impedance paths and reduce the effect of glitches
on the power supply lines. Good decoupling is also important to
lower the supply’s impedance presented to the AD7654 and
to reduce the magnitude of the supply spikes. Decoupling ceramic
capacitors, typically 100 nF, should be placed on each power
supply’s pins, AVDD, DVDD, and OVDD, close to and ideally
right up against these pins and their corresponding ground pins.
Additionally, low ESR 10 µF capacitors should be located in the
vicinity of the ADC to further reduce low frequency ripple.
The DVDD supply of the AD7654 can be either a separate
supply or come from the analog supply, AVDD, or from the
digital interface supply, OVDD. When the system digital supply
is noisy or fast switching digital signals are present, it is recommended that if no separate supply is available, the DVDD digital
supply should be connected to the analog supply AVDD through an
RC filter, as shown in Figure 5, and the system supply should
be connected to the interface digital supply OVDD and the
remaining digital circuitry. When DVDD is powered from the
system supply, it is useful to insert a bead to further reduce high
frequency spikes.
The AD7654 has four different ground pins: REFGND, AGND,
DGND, and OGND. REFGND senses the reference voltage
and should be a low impedance return to the reference because
it carries pulsed currents. AGND is the ground to which most
internal ADC analog signals are referenced. This ground must
be connected with the least resistance to the analog ground
plane. DGND must be tied to the analog or digital ground
plane depending on the configuration. OGND is connected to
the digital system ground.
The layout of the decoupling of the reference voltage is important. The decoupling capacitor should be close to the ADC and
connected with short and large traces to minimize parasitic
inductances.
Evaluating the AD7654’s Performance
APPLICATION HINTS
Layout
The AD7654 has very good immunity to noise on the power
supplies, as seen in Figure 5. However, care should still be
taken with regard to grounding layout.
A recommended layout for the AD7654 is outlined in the
documentation of the evaluation board for the AD7654. The
evaluation board package includes a fully assembled and tested
evaluation board, documentation, and software for controlling
the board from a PC via the Eval-Control BRD2.
The printed circuit board that houses the AD7654 should be
designed so the analog and digital sections are separated and
confined to certain areas of the board. This facilitates the use of
–20–
REV. 0
AD7654
OUTLINE DIMENSIONS
48-Lead Plastic Quad Flatpack [LQFP]
1.4mm Thick
(ST-48)
Dimensions shown in millimeters
1.60 MAX
PIN 1
INDICATOR
0.75
0.60
0.45
9.00 BSC
37
48
36
1
1.45
1.40
1.35
SEATING
PLANE
0.20
0.09
0.15
0.05
SEATING
PLANE
7.00
BSC
TOP VIEW
(PINS DOWN)
VIEW A
7
3.5
0
0.08 MAX
COPLANARITY
25
12
24
13
0.27
0.22
0.17
0.50
BSC
VIEW A
ROTATED 90 CCW
COMPLIANT TO JEDEC STANDARDS MS-026BBC
48-Lead Frame Chip Scale Package [LFCSP]
(CP-48)
Dimensions shown in millimeters
7.00
BSC SQ
0.60 MAX
0.60 MAX
37
6.75
BSC SQ
TOP
VIEW
0.25
REF
48
1
12
25
24
13
5.50
REF
0.70 MAX
0.65 NOM
0.05 MAX
0.02 NOM
0.50 BSC
SEATING
PLANE
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2
REV. 0
5.25
4.70 SQ
2.25
BOTTOM
VIEW
0.50
0.40
0.30
12 MAX
PIN 1
INDICATOR
36
PIN 1
INDICATOR
1.00
0.90
0.80
0.30
0.23
0.18
–21–
–22–
–23–
–24–
PRINTED IN U.S.A.
C03057–0–10/02(0)