Low Cost DC-500 MHz, 92 dB Logarithmic Amplifier AD8307 FUNCTIONAL BLOCK DIAGRAM FEATURES APPLICATIONS Conversion of signal level to decibel form Transmitter antenna power measurement Receiver signal strength indication (RSSI) Low cost radar and sonar signal processing Network and spectrum analyzers (to 120 dB) Signal level determination down to 20 Hz True decibel ac mode for multimeters AD8307 VPS 7 INP 8 INM 1 7.5mA BAND GAP REFERENCE AND BIASING SIX 14.3dB 900MHz AMPLIFIER STAGES +INP ENB 5 INT 4 OUT 3 OFS MIRROR 1.1kΩ –INP 6 3 NINE DETECTOR CELLS SPACED 14.3dB COM 2 2 2µA /dB 12.5kΩ COM INPUT-OFFSET COMPENSATION LOOP 01082-001 Complete multistage logarithmic amplifier 92 dB dynamic range: –75 dBm to +17 dBm to –90 dBm using matching network Single supply of 2.7 V minimum at 7.5 mA typ DC to 500 MHz operation, ±1 dB linearity Slope of 25 mV/dB, intercept of −84 dBm Highly stable scaling over temperature Fully differential dc-coupled signal path 100 ns power-up time, 150 μA sleep current Figure 1. GENERAL DESCRIPTION The AD8307 is the first logarithmic amplifier made available in an 8-lead (SOIC-8) package. It is a complete 500 MHz monolithic demodulating logarithmic amplifier based on the progressive compression (successive detection) technique, providing a dynamic range of 92 dB to ±3 dB law-conformance and 88 dB to a tight ±1 dB error bound at all frequencies up to 100 MHz. It is extremely stable and easy to use, requiring no significant external components. A single-supply voltage of 2.7 V to 5.5 V at 7.5 mA is needed, corresponding to an unprecedented power consumption of only 22.5 mW at 3 V. A fast acting CMOScompatible control pin can disable the AD8307 to a standby current of less than 150 μA. Each of the cascaded amplifier/limiter cells has a small signal gain of 14.3 dB, with a −3 dB bandwidth of 900 MHz. The input is fully differential and at a moderately high impedance (1.1 kΩ in parallel with about 1.4 pF). The AD8307 provides a basic dynamic range extending from approximately −75 dBm (where dBm refers to a 50 Ω source, that is, a sine amplitude of about ±56 μV) up to +17 dBm (a sine amplitude of ±2.2 V). A simple input matching network can lower this range to –88 dBm to +3 dBm. The logarithmic linearity is typically within ±0.3 dB up to 100 MHz over the central portion of this range, and degrades only slightly at 500 MHz. There is no minimum frequency limit. The AD8307 can be used at audio frequencies of 20 Hz or lower. The output is a voltage scaled 25 mV/dB, generated by a current of nominally 2 μA/dB through an internal 12.5 kΩ resistor. This voltage varies from 0.25 V at an input of −74 dBm (that is, the ac intercept is at −84 dBm, a 20 μV rms sine input), up to 2.5 V for an input of +16 dBm. This slope and intercept can be trimmed using external adjustments. Using a 2.7 V supply, the output scaling can be lowered, for example to 15 mV/dB, to permit utilization of the full dynamic range. The AD8307 exhibits excellent supply insensitivity and temperature stability of the scaling parameters. The unique combination of low cost, small size, low power consumption, high accuracy and stability, very high dynamic range, and a frequency range encompassing audio through IF to UHF makes this product useful in numerous applications requiring the reduction of a signal to its decibel equivalent. The AD8307 operates over the industrial temperature range of −40°C to +85°C, and is available in 8-lead SOIC and PDIP packages. Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2006 Analog Devices, Inc. All rights reserved. AD8307 TABLE OF CONTENTS Features .............................................................................................. 1 Input Interface ............................................................................ 14 Applications....................................................................................... 1 Offset Interface ........................................................................... 15 Functional Block Diagram .............................................................. 1 Output Interface ......................................................................... 15 General Description ......................................................................... 1 Theory of Operation ...................................................................... 17 Revision History ............................................................................... 2 Basic Connections...................................................................... 17 Specifications..................................................................................... 3 Input Matching ........................................................................... 17 Absolute Maximum Ratings............................................................ 4 Narrow-Band Matching ............................................................ 18 ESD Caution.................................................................................. 4 Slope and Intercept Adjustments ............................................. 19 Pin Configuration and Function Descriptions............................. 5 Applications Information .............................................................. 20 Typical Performance Characteristics ............................................. 6 Buffered Output.......................................................................... 20 Log Amp Theory .............................................................................. 9 Four Pole Filter ........................................................................... 20 Progressive Compression .......................................................... 10 1 μW to 1 kW 50 Ω Power Meter............................................. 21 Demodulating Log Amps .......................................................... 11 Measurement System with 120 dB Dynamic Range.............. 21 Intercept Calibration.................................................................. 12 Operation at Low Frequencies.................................................. 22 Offset Control ............................................................................. 12 DC-Coupled Applications......................................................... 22 Extension of Range..................................................................... 13 Operation Above 500 MHz....................................................... 23 Interfaces.......................................................................................... 14 Outline Dimensions ....................................................................... 24 Enable Interface .......................................................................... 14 Ordering Guide .......................................................................... 24 REVISION HISTORY 10/06—Rev. B to Rev. C Updated Format..................................................................Universal Changes to Table 1............................................................................ 3 Changes to Table 3............................................................................ 5 Changes to Offset Interface........................................................... 15 Changes to Output Interface......................................................... 15 Updated captions to Outline Dimensions................................... 24 Changes to Ordering Guide .......................................................... 24 6/03—Rev. A to Rev. B Renumbered TPCs and Figures........................................Universal Changes to Ordering Guide ............................................................ 3 Changes to Figure 24...................................................................... 17 Deleted Evaluation Board Information ....................................... 18 Updated Outline Dimensions ....................................................... 19 Rev. C | Page 2 of 24 AD8307 SPECIFICATIONS VS = 5 V, TA = 25°C, RL ≥ 1 MΩ, unless otherwise noted. Table 1. Parameter GENERAL CHARACTERISTICS Input Range (±3 dB Error) Input Range (±1 dB Error) Logarithmic Conformance Logarithmic Slope vs. Temperature Logarithmic Intercept vs. Temperature Input Noise Spectral Density Operating Noise Floor Output Resistance Internal Load Capacitance Response Time Upper Usable Frequency 3 Lower Usable Frequency AMPLIFIER CELL CHARACTERISTICS Cell Bandwidth Cell Gain INPUT CHARACTERISTICS DC Common-Mode Voltage Common-Mode Range DC Input Offset Voltage 4 Incremental Input Resistance Input Capacitance Bias Current POWER INTERFACES Supply Voltage Supply Current Disabled Conditions From noise floor to maximum input From noise floor to maximum input f ≤ 100 MHz, central 80 dB f = 500 MHz, central 75 dB Unadjusted 1 Sine amplitude, unadjusted 2 Equivalent sine power in 50 Ω Inputs shorted RSOURCE = 50 Ω/2 Pin 4 to ground Min 23 23 −87 −88 10 Small signal, 10% to 90%, 0 mV to100 mV, CL = 2 pF Large signal, 10% to 90%, 0 V to 2.4 V, CL = 2 pF AC-coupled input −3 dB AC-coupled input Either input (small signal) RSOURCE ≤ 50 Ω Drift Differential Either pin to ground Either input −0.3 Typ 92 88 ±0.3 ±0.5 25 20 −84 1.5 −78 12.5 3.5 400 27 27 −77 −76 15 500 10 MHz Hz 900 14.3 MHz dB 3.2 1.6 50 0.8 1.1 1.4 10 25 V V μV μV/°C kΩ pF μA 5.5 10 750 V mA μA VS − 1 500 This can be adjusted downward by adding a shunt resistor from the output to ground. A 50 kΩ resistor reduces the nominal slope to 20 mV/dB. This can be adjusted in either direction by a voltage applied to Pin 5, with a scale factor of 8 dB/V. See the Operation Above 500 MHz section. 4 Normally nulled automatically by internal offset correction loop. May be manually nulled by a voltage applied between Pin 3 and ground; see the Applications Information section. 2 3 Rev. C | Page 3 of 24 dB dB dB dB mV/dB mV/dB μV dBm dBm nV/√Hz dBm kΩ pF ns ns 8 150 1 ±1 Unit 500 2.7 VENB ≥ 2 V VENB ≤ 1 V Max AD8307 ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Supply Input Voltage (Pin 1 and Pin 8) Storage Temperature Range, N, R Ambient Temperature Range, Rated Performance Industrial, AD8307AN, AD8307AR Lead Temperature Range (Soldering 10 sec) Ratings 7.5 V VSUPPLY −65°C to +125°C −40°C to +85°C Stresses above those listed under Absolute Maximum Ratings can cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods can affect device reliability. ESD CAUTION 300°C Rev. C | Page 4 of 24 AD8307 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS INM 1 COM 2 AD8307 8 INP 7 VPS 6 ENB TOP VIEW OUT 4 (Not to Scale) 5 INT 01082-002 OFS 3 Figure 2. Pin Configuration Table 3. Pin Function Descriptions Pin No. 1 2 3 4 5 6 7 8 Mnemonic INM COM OFS OUT INT ENB VPS INP Description Signal Input Minus Polarity. Normally at VPOS/2. Common Pin (Usually Grounded). Offset Adjustment. External capacitor connection. Logarithmic (RSSI) Output Voltage. ROUT = 12.5 kΩ. Intercept Adjustment, ±3 dB (see the Slope and Intercept Adjustments section). CMOS-Compatible Chip Enable. Active when high. Positive Supply: 2.7 V to 5.5 V. Signal Input Plus Polarity. Normally at VPOS/2. Due to the symmetrical nature of the response, there is no special significance to the sign of the two input pins. DC resistance from INP to INM = 1.1 kΩ. Rev. C | Page 5 of 24 AD8307 TYPICAL PERFORMANCE CHARACTERISTICS 8 3 7 1 5 ERROR (dB) 4 3 TEMPERATURE ERROR @ +85°C 0 TEMPERATURE ERROR @ +25°C –1 TEMPERATURE ERROR @ –40°C 2 –2 0 1.0 01082-003 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 –3 –80 2.0 01082-006 SUPPLY CURRENT (mA) 2 6 –60 VENB (V) –40 –20 0 20 INPUT LEVEL (dBm) Figure 3. Supply Current vs. VENB Voltage (5 V) Figure 6. Log Conformance vs. Input Level (dBm) at +25°C, +85°C, and −40°C 3 8 INPUT FREQUENCY 10MHz 6 2 5 INPUT FREQUENCY 100MHz VOUT (V) 4 3 1 INPUT FREQUENCY 300MHz 2 INPUT FREQUENCY 500MHz 0 1.0 01082-004 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 0 –80 2.0 01082-007 SUPPLY CURRENT (mA) 7 –60 VENB (V) 3 1.5 2 1.0 0 20 0.5 ERROR (dB) CFO VALUE = 0.01µF 0 –0.5 –1 FREQUENCY INPUT = 100MHz CFO VALUE = 1µF CFO VALUE = 0.1µF –1.0 01082-005 –2 –60 –40 –20 0 –1.5 –80 20 01082-008 ERROR (dB) FREQUENCY INPUT = 300MHz 0 –3 –80 –20 Figure 7. VOUT vs. Input Level (dBm) at Various Frequencies Figure 4. Supply Current vs. VENB Voltage (3 V) 1 –40 INPUT LEVEL (dBm) –60 –40 –20 0 20 INPUT LEVEL (dBm) INPUT LEVEL (dBm) Figure 5. Log Conformance vs. Input Level (dBm) 100 MHz, and 300 MHz Rev. C | Page 6 of 24 Figure 8. Log Conformance vs. CFO Values at 1 kHz Input Frequency AD8307 3.0 3 100MHz INT PIN = 3.0V 10MHz, INT = –96.52dBm 2.5 2 1 ERROR (dB) INT PIN = 4.0V 10MHz, INT = –87.71dBm 1.5 NO CONNECT ON INT 10MHz, INT = –82.90dBm 1.0 +INPUT 0 –1 0.5 –INPUT 01082-009 –2 0 –80 –70 –60 –50 –40 –30 –20 –10 0 10 01082-012 VOUT (V) 2.0 –3 –80 20 –60 INPUT LEVEL (dBm) Figure 9. VOUT vs. Input Level at 5 V Supply; Showing Intercept Adjustment 0 20 3 2 INT VOLTAGE INT = 1.0V, INT = –86dBm 500MHz 1 ERROR (dB) INT VOLTAGE INT NO CONNECT, INT = –71dBm 1.5 1.0 0 –1 0 –80 –70 –60 –50 –40 –30 –20 –10 0 –2 01082-010 INT VOLTAGE INT = 2.0V, INT = –78dBm 0.5 100MHz 01082-013 2.5 VOUT (V) –20 Figure 12. Log Conformance vs. Input Level at 100 MHz Showing Response to Alternative Inputs 3.0 2.0 –40 INPUT LEVEL (dBm) –3 –90 10 –70 INPUT LEVEL (dBm) –50 –30 –10 10 INPUT LEVEL (dBm) Figure 13. Log Conformance vs. Input at 100 MHz, 500 MHz; Input Driven Differentially Using Transformer Figure 10. VOUT vs. Input Level at 3 V Supply Using AD820 as Buffer, Gain = +2; Showing Intercept Adjustment 3 2.5 2 2.0 500MHz 1.0 ERROR (dB) VOUT (V) 1 1.5 100MHz @ –40°C 100MHz @ +25°C 0 100MHz –1 0.5 –60 –40 –20 01082-011 0 –3 –70 20 01082-014 –2 100MHz @ +85°C 0 –80 10MHz –60 –50 –40 –30 –20 –10 0 10 INPUT LEVEL (dBm) INPUT LEVEL (dBm) Figure 11. VOUT vs. Input Level at Three Temperatures (−40°C, +25°C, +85°C) Rev. C | Page 7 of 24 Figure 14. Log Conformance vs. Input Level at 3 V Supply Using AD820 as Buffer, Gain = +2 20 AD8307 2V VOUT CH 1 CH1 200mV VOUT CH1 CH1 500mV CH1 GND 500ns CH2 2.00V CH2 GND 01082-015 GND INPUT SIGNAL CH2 VOUT CH 1 200ns CH2 1.00V Figure 15. Power-Up Response Time 01082-018 VENB CH 2 Figure 18. VOUT Rise Time CH1 200mV CH1 500mV 2.5V INPUT SIGNAL CH2 VENB CH 2 CH2 GND VOUT CH1 01082-016 GND 500ns Figure 16. Power-Down Response Time Figure 19. Large Signal Response Time HP8648B 10MHz REF CLK SIGNAL GENERATOR PULSE MODE IN PULSE VPS = 5.0V MODULATION MODE 0.1µF 1nF RF OUT VPS = 5.0V HP8648B SIGNAL GENERATOR HP8112A PULSE GENERATOR OUT 0.1µF 1nF RF OUT SYNCH OUT NC 8 7 6 8 5 52.3Ω AD8307 3 1nF NC = NO CONNECT TEK P6139A 10x PROBE TRIG HP8112A OUT PULSE GENERATOR NC 5 AD8307 1 4 NC TEK744A SCOPE 2 3 4 NC TRIG 1nF 01082-017 2 6 OUT INM COM OFS OUT INM COM OFS OUT 1 7 EXT TRIG INP VPS ENB INT INP VPS ENB INT 52.3Ω 200ns CH2 1.00V TEK P6204 FET PROBE TEK744A SCOPE NC = NO CONNECT Figure 20. Test Setup for VOUT Pulse Response Figure 17. Test Setup for Power-Up/Power-Down Response Time Rev. C | Page 8 of 24 TRIG 01082-020 CH2 2.00V 01082-019 CH1 GND AD8307 LOG AMP THEORY Logarithmic amplifiers perform a more complex operation than that of classical linear amplifiers, and their circuitry is significantly different. A good grasp of what log amps do and how they work can prevent many pitfalls in their application. The essential purpose of a log amp is not to amplify, though amplification is utilized to achieve the function. Rather, it is to compress a signal of wide dynamic range to its decibel equivalent. It is thus a measurement device. A better term might be logarithmic converter, since its basic function is the conversion of a signal from one domain of representation to another, via a precise nonlinear transformation. Logarithmic compression leads to situations that can be confusing or paradoxical. For example, a voltage offset added to the output of a log amp is equivalent to a gain increase ahead of its input. In the usual case where all the variables are voltages, and regardless of the particular structure, the relationship between the variables can be expressed as: VOUT = VY log (VIN /VX ) (1) where: VOUT is the output voltage. VY is the slope voltage; the logarithm is usually taken to base 10 (in which case VY is also the volts per decade). VIN is the input voltage. VX is the intercept voltage. All log amps implicitly require two references, here, VX and VY, which determine the scaling of the circuit. The absolute accuracy of a log amp cannot be any better than the accuracy of its scaling references. Equation 1 is mathematically incomplete in representing the behavior of a demodulating log amp such as the AD8307, where VIN has an alternating sign. However, the basic principles are unaffected, and this can be safely used as the starting point in the analyses of log amp scaling. VOUT 5VY 4VY 3VY (the log intercept) at the unique value VIN = VX and ideally becomes negative for inputs below the intercept. In the ideal case, the straight line describing VOUT for all values of VIN continues indefinitely in both directions. The dotted line shows that the effect of adding an offset voltage VSHIFT to the output is to lower the effective intercept voltage VX. Exactly the same alteration could be achieved by raising the gain (or signal level) ahead of the log amp by the factor VSHIFT/VY. For example, if VY is 500 mV per decade (25 mV/dB), an offset of +150 mV added to the output appears to lower the intercept by two tenths of a decade, or 6 dB. Adding an offset to the output is thus indistinguishable from applying an input level that is 6 dB higher. The log amp function described by Equation 1 differs from that of a linear amplifier in that the incremental gain δVOUT/δVIN is a very strong function of the instantaneous value of VIN, as is apparent by calculating the derivative. For the case where the logarithmic base is δ, δVOUT V = Y VIN δVIN That is, the incremental gain is inversely proportional to the instantaneous value of the input voltage. This remains true for any logarithmic base, which is chosen as 10 for all decibel related purposes. It follows that a perfect log amp is required to have infinite gain under classical small signal (zero amplitude) conditions. Less ideally, this result indicates that, whatever means are used to implement a log amp, accurate response under small signal conditions (that is, at the lower end of the dynamic range) demands the provision of a very high gain bandwidth product. A further consequence of this high gain is that, in the absence of an input signal, even very small amounts of thermal noise at the input of a log amp cause a finite output for zero input. This results in the response line curving away from the ideal shown in Figure 21 toward a finite baseline, which can be either above or below the intercept. Note that the value given for this intercept can be an extrapolated value, in which case the output can not cross zero, or even reach it, as is the case for the AD8307. While Equation 1 is fundamentally correct, a simpler formula is appropriate for specifying the calibration attributes of a log amp like the AD8307, which demodulates a sine wave input: VSHIFT LOWER INTERCEPT 2VY VOUT = VSLOPE (PIN – P0) VY (3) where: VIN = VX 0dBc VIN = 102VX +40dBc VIN = 104VX +80dBc 01082-021 LOG VIN VOUT = 0 VIN = 10–2VX –40dBc (2) VOUT is the demodulated and filtered baseband (video or RSSI) output. VSLOPE is the logarithmic slope, now expressed in V/dB (typically between 15 mV/dB and 30 mV/dB). –2V Y Figure 21. Ideal Log Amp Function Figure 21 shows the input/output relationship of an ideal log amp, conforming to Equation 1. The horizontal scale is logarithmic and spans a wide dynamic range, shown here as over 120 dB, or six decades. The output passes through zero PIN is the input power, expressed in decibels relative to some reference power level. P0 is the logarithmic intercept, expressed in decibels relative to the same reference level. Rev. C | Page 9 of 24 AD8307 in the case of the AD8307, VY is traceable to an on-chip band gap reference, while VX is derived from the thermal voltage kT/q and is later temperature corrected. OUTPUT A/1 0 A A INPUT A VW Let the input of an N-cell cascade be VIN, and the final output VOUT. For small signals, the overall gain is simply AN. A six stage system in which A = 5 (14 dB) has an overall gain of 15,625 (84 dB). The importance of a very high small signal gain in implementing the logarithmic function has been noted; however, this parameter is only of incidental interest in the design of log amps. From here onward, rather than considering gain, analyze the overall nonlinear behavior of the cascade in response to a simple dc input, corresponding to the VIN of Equation 1. For very small inputs, the output from the first cell is V1 = AVIN. The output from the second cell is V2 = A2 VIN, and so on, up to VN = AN VIN. At a certain value of VIN, the input to the Nth cell, VN–1, is exactly equal to the knee voltage EK. Thus, VOUT = AEK and since there are N–1 cells of gain A ahead of this node, calculate VIN = EK /AN–1. This unique situation corresponds to the lin-log transition, (labeled 1 in Figure 24). Below this input, the cascade of gain cells acts as a simple linear amplifier, while for higher values of VIN, it enters into a series of segments that lie on a logarithmic approximation (dotted line). VOUT Figure 22. Cascade of Nonlinear Gain Cells To develop the theory, first consider a scheme slightly different from that employed in the AD8307, but simpler to explain and mathematically more straightforward to analyze. This approach is based on a nonlinear amplifier unit, called an A/1 cell, with the transfer characteristic shown in Figure 23. (4A–3) E K The local small signal gain δVOUT/δVIN is A, maintained for all inputs up to the knee voltage EK, above which the incremental gain drops to unity. The function is symmetrical: the same drop in gain occurs for instantaneous values of VIN less than –EK. The large signal gain has a value of A for inputs in the range −EK ≤ VIN ≤ +EK, but falls asymptotically toward unity for very large inputs. In logarithmic amplifiers based on this amplifier function, both the slope voltage and the intercept voltage must be traceable to the one reference voltage, EK. Therefore, in this fundamental analysis, the calibration accuracy of the log amp is dependent solely on this voltage. In practice, it is possible to separate the basic references used to determine VY and VX and AEK 2 3 (3A–2) E K 3 (A–1) EK (2A–1) E K 2 1 RATIO OF A LOG VIN 0 EK/AN–1 EK/AN–2 EK/AN–3 EK/AN–4 01082-024 A STAGE N 01082-022 VX STAGE N–1 EK Figure 23. A/1 Amplifier Function Most high speed, high dynamic range log amps use a cascade of nonlinear amplifier cells (Figure 22) to generate the logarithmic function from a series of contiguous segments, a type of piecewise linear technique. This basic topology immediately opens up the possibility of enormous gain bandwidth products. For example, the AD8307 employs six cells in its main signal path, each having a small signal gain of 14.3 dB (×5.2) and a −3 dB bandwidth of about 900 MHz. The overall gain is about 20,000 (86 dB) and the overall bandwidth of the chain is some 500 MHz, resulting in the incredible gain bandwidth product (GBW) of 10,000 GHz, about a million times that of a typical op amp. This very high GBW is an essential prerequisite for accurate operation under small signal conditions and at high frequencies. In Equation 2, however, the incremental gain decreases rapidly as VIN increases. The AD8307 continues to exhibit an essentially logarithmic response down to inputs as small as 50 μV at 500 MHz. STAGE 2 SLOPE = 1 SLOPE = A PROGRESSIVE COMPRESSION STAGE 1 AEK 01082-023 The most widely used reference in RF systems is decibels above 1 mW in 50 Ω, written dBm. Note that the quantity (PIN – P0) is just dB. The logarithmic function disappears from the formula because the conversion has already been implicitly performed in stating the input in decibels. This is strictly a concession to popular convention; log amps manifestly do not respond to power (tacitly, power absorbed at the input), but rather to input voltage. The use of dBV (decibels with respect to 1 V rms) is more precise, though still incomplete, since waveform is involved, too. Since most users think about and specify RF signals in terms of power, more specifically, in dBm re: 50 Ω, this convention is used in specifying the performance of the AD8307. Figure 24. First Three Transitions Continuing this analysis, the next transition occurs when the input to the (N–1) stage just reaches EK; that is, when VIN = EK /AN–2. The output of this stage is then exactly AEK, and it is easily demonstrated (from the function shown in Figure 23) that the output of the final stage is (2A–1) EK (labeled 2 in Figure 24). Thus, the output has changed by an amount (A–1)EK for a change in VIN from EK /AN–1 to EK/AN–2, that is, a ratio change Rev. C | Page 10 of 24 AD8307 of A. At the next critical point (labeled 3 in Figure 24), the input is again A times larger and VOUT has increased to (3A–2)EK, that is, by another linear increment of (A–1)EK. VY = Linear Change in VOUT Decades Change in VIN = ( A − 1)EK log10 ( A) (4) Note that only two design parameters are involved in determining VY, namely, the cell gain A and the knee voltage EK, while N, the number of stages, is unimportant in setting the slope of the overall function. For A = 5 and EK = 100 mV, the slope would be a rather awkward 572.3 mV per decade (28.6 mV/dB). A well designed log amp has rational scaling parameters. The intercept voltage can be determined by using two pairs of transition points on the output function (consider Figure 24). The result is VX = EK ( N +1 / ( A −1)) A (5) For the case under consideration, using N = 6, calculate VZ = 4.28 μV. However, be careful about the interpretation of this parameter, since it was earlier defined as the input voltage at which the output passes through zero (see Figure 21). Clearly, in the absence of noise and offsets, the output of the amplifier chain shown in Figure 23 can be zero when, and only when, VIN = 0. This anomaly is due to the finite gain of the cascaded amplifier, which results in a failure to maintain the logarithmic approximation below the lin-log transition (point 1 in Figure 24). Closer analysis shows that the voltage given by Equation 5 represents the extrapolated, rather than actual, intercept. DEMODULATING LOG AMPS Log amps based on a cascade of A/1 cells are useful in baseband applications because they do not demodulate their input signal. However, baseband and demodulating log amps alike can be made using a different type of amplifier stage, called an A/0 cell. Its function differs from that of the A/1 cell in that the gain above the knee voltage EK falls to zero, as shown by the solid line in Figure 25. This is also known as the limiter function, and a chain of N such cells are often used to generate hard limited output in recovering the signal in FM and PM modes. tanh SLOPE = A 0 EK INPUT 01082-025 A/0 OUTPUT Further analysis shows that right up to the point where the input to the first cell is above the knee voltage, VOUT changes by (A–1)EK for a ratio change of A in VIN. This can be expressed as a certain fraction of a decade, which is simply log10(A). For example when A = 5, a transition in the piecewise linear output function occurs at regular intervals of 0.7 decade (log10(A), or 14 dB divided by 20 dB). This insight allows us to immediately write the volts per decade scaling parameter, which is also the scaling voltage, VY, when using base 10 logarithms, as SLOPE = 0 AEK Figure 25. A/0 Amplifier Functions (Ideal and Tanh) The AD640, AD606, AD608, AD8307, and various other Analog Devices, Inc. communications products incorporating a logarithmic IF amplifier all use this technique. It becomes apparent that the output of the last stage can no longer provide the logarithmic output, since this remains unchanged for all inputs above the limiting threshold, which occurs at VIN = EK/AN−1. Instead, the logarithmic output is now generated by summing the outputs of all the stages. The full analysis for this type of log amp is only slightly more complicated than that of the previous case. It is readily shown that, for practical purposes, the intercept voltage VX is identical to that given in Equation 5, while the slope voltage is VY = AEK log10 ( A ) (6) Preference for the A/0 style of log amp, over one using A/1 cells, stems from several considerations. The first is that an A/0 cell can be very simple. In the AD8307 it is based on a bipolar transistor differential pair, having resistive loads, RL, and an emitter current source, IE. This exhibits an equivalent knee voltage of EK = 2 kT/q and a small signal gain of A = IERL/EK. The large signal transfer function is the hyperbolic tangent (see dotted line in Figure 25). This function is very precise, and the deviation from an ideal A/0 form is not detrimental. In fact, the rounded shoulders of the tanh function result in a lower ripple in the logarithmic conformance than that obtained using an ideal A/0 function. An amplifier built of these cells is entirely differential in structure and can thus be rendered very insensitive to disturbances on the supply lines and, with careful design, to temperature variations. The output of each gain cell has an associated transconductance (gm) cell, which converts the differential output voltage of the cell to a pair of differential currents, which are summed simply by connecting the outputs of all the gm (detector) stages in parallel. The total current is then converted back to a voltage by a transresistance stage to generate the logarithmic output. This scheme is depicted, in single sided form, in Figure 26. Rev. C | Page 11 of 24 AD8307 A/0 gm A/0 gm A3VIN A/0 gm A4VIN gm motion of VX resulting from the temperature variation of EK. Do this by adding an offset with the required temperature behavior. VLIM A/0 gm IOUT 01082-026 A2VIN AVIN VIN Figure 26. Log Amp Using A/0 Stages and Auxiliary Summing Cells The chief advantage of this approach is that the slope voltage can now be decoupled from the knee voltage EK = 2 kT/q, which is inherently PTAT. By contrast, the simple summation of the cell outputs would result in a very high temperature coefficient of the slope voltage given in Equation 6. To do this, the detector stages are biased with currents (not shown) which are rendered stable with temperature. These are derived either from the supply voltage (as in the AD606 and AD608) or from an internal band gap reference (as in the AD640 and AD8307). This topology affords complete control over the magnitude and temperature behavior of the logarithmic slope, decoupling it completely from EK. A further step is needed to achieve the demodulation response, required when the log amp is to convert an alternating input into a quasi-dc baseband output. This is achieved by altering the gm cells used for summation purposes to also implement the rectification function. Early discrete log amps based on the progressive compression technique used half-wave rectifiers. This made post-detection filtering difficult. The AD640 was the first commercial monolithic log amp to use a full wave rectifier, a practice followed in all subsequent Analog Devices types. These detectors can be modeled as being essentially linear gm cells, but producing an output current independent of the sign of the voltage applied to the input of each cell. That is, they implement the absolute value function. Since the output from the later A/0 stages closely approximates an amplitude symmetric square wave for even moderate input levels (most stages of the amplifier chain operate in a limiting mode), the current output from each detector is almost constant over each period of the input. Somewhat earlier detector stages produce a waveform having only very brief dropouts, while the detectors nearest the input produce a low level, almost sinusoidal waveform at twice the input frequency. These aspects of the detector system result in a signal that is easily filtered, resulting in low residual ripple on the output. INTERCEPT CALIBRATION All monolithic log amps from Analog Devices include accurate means to position the intercept voltage VX (or equivalent power for a demodulating log amp). Using the scheme shown in Figure 26, the basic value of the intercept level departs considerably from that predicted by the simpler analyses given earlier. However, the intrinsic intercept voltage is still proportional to EK, which is PTAT (Equation 5). Recalling that the addition of an offset to the output produces an effect that is indistinguishable from a change in the position of the intercept, it is possible to cancel the left-right The precise temperature shaping of the intercept positioning offset results in a log amp having stable scaling parameters, making it a true measurement device, for example, as a calibrated received signal strength indicator (RSSI). In this application, one is more interested in the value of the output for an input waveform that is invariably sinusoidal. Although the input level can alternatively be stated as an equivalent power, in dBm, be sure to work carefully. It is essential to know the load impedance in which this power is presumed to be measured. In RF practice, it is generally safe to assume a reference impedance of 50 Ω in which 0 dBm (1 mW) corresponds to a sinusoidal amplitude of 316.2 mV (223.6 mV rms). The intercept can likewise be specified in dBm. For the AD8307, it is positioned at −84 dBm, corresponding to a sine amplitude of 20 μV. It is important to bear in mind that log amps do not respond to power, but to the voltage applied to their input. The AD8307 presents a nominal input impedance much higher than 50 Ω (typically 1.1 kΩ low frequencies). A simple input matching network can considerably improve the sensitivity of this type of log amp. This increases the voltage applied to the input and thus alters the intercept. For a 50 Ω match, the voltage gain is 4.8 and the entire dynamic range moves down by 13.6 dB (see Figure 35). Note that the effective intercept is a function of waveform. For example, a square wave input reads 6 dB higher than a sine wave of the same amplitude and a Gaussian noise input 0.5 dB higher than a sine wave of the same rms value. OFFSET CONTROL In a monolithic log amp, direct coupling between the stages is used for several reasons. First, this avoids the use of coupling capacitors, which typically have a chip area equal to that of a basic gain cell, thus considerably increasing die size. Second, the capacitor values predetermine the lowest frequency at which the log amp can operate; for moderate values, this can be as high as 30 MHz, limiting the application range. Third, the parasitic (backplate) capacitance lowers the bandwidth of the cell, further limiting the applications. However, the very high dc gain of a direct-coupled amplifier raises a practical issue. An offset voltage in the early stages of the chain is indistinguishable from a real signal. For example, if it were as high as 400 μV, it would be 18 dB larger than the smallest ac signal (50 μV), potentially reducing the dynamic range by this amount. This problem is averted by using a global feedback path from the last stage to the first, which corrects this offset in a similar fashion to the dc negative feedback applied around an op amp. The high frequency components of the signal must be removed to prevent a reduction of the HF gain in the forward path. In the AD8307, this is achieved by an on-chip filter, providing sufficient suppression of HF feedback to allow operation above Rev. C | Page 12 of 24 AD8307 1 MHz. To extend the range below this frequency, an external capacitor can be added. This permits the high-pass corner to be lowered to audio frequencies using a capacitor of modest value. Note that this capacitor has no effect on the minimum signal frequency for input levels above the offset voltage: this extends down to dc (for a signal applied directly to the input pins). The offset voltage varies from part to part; some exhibit essentially stable offsets of under 100 μV without the benefit of an offset adjustment. EXTENSION OF RANGE The theoretical dynamic range for the basic log amp shown in Figure 26 is AN. For A = 5.2 (14.3 dB) and N = 6, it is 20,000 or 86 dB. The actual lower end of the dynamic range is largely determined by the thermal noise floor, measured at the input of the chain of amplifiers. The upper end of the range is extended upward by the addition of top end detectors. The input signal is applied to a tapped attenuator, and progressively smaller signals are applied to three passive rectifying gm cells whose outputs are summed with those of the main detectors. With care in design, the extension to the dynamic range can be seamless over the full frequency range. For the AD8307, it amounts to a further 27 dB. Therefore, the total dynamic range is theoretically 113 dB. The specified range of 90 dB (−74 dBm to +16 dBm) is for high accuracy and calibrated operation, and includes the low end degradation due to thermal noise and the top end reduction due to voltage limitations. The additional stages are not, however, redundant, but are needed to maintain accurate logarithmic conformance over the central region of the dynamic range, and in extending the usable range considerably beyond the specified range. In applications where log conformance is less demanding, the AD8307 can provide over 95 dB of range. Rev. C | Page 13 of 24 AD8307 INTERFACES ENABLE INTERFACE The chip enable interface is shown in Figure 28. The currents in the diode-connected transistors control the turn on and turn off states of the band gap reference and the bias generator, and are a maximum of 100 μA when Pin 6 is taken to 5 V, under worstcase conditions. Left unconnected, or at a voltage below 1 V, the AD8307 is disabled and consume a sleep current of under 50 μA; tied to the supply, or a voltage above 2 V, it is fully enabled. The internal bias circuitry is very fast, typically <100 ns for either off or on. In practice, the latency period before the log amp exhibits its full dynamic range is more likely to be limited by factors relating to the use of ac coupling at the input or the settling of the offset control loop. AD8307 40kΩ ENB 6 TO BIAS STAGES COM 2 Figure 28. Enable Interface 7 AD8307 INP 8 INM 1 7.5mA +INP S BAND GAP REFERENCE AND BIASING 1.1kΩ MIRROR –INP 3 2µA /dB COM 2 ENB 5 INT 2 CP INP 4 OUT INM 3 OFS 125Ω 2kΩ 6kΩ Q1 4kΩ TOP-END DETECTORS ~3kΩ Q2 1 TYP 2.2V FOR 3V SUPPLY, 3.2V AT 5V CM COM INPUT-OFFSET COMPENSATION LOOP 2kΩ 8 CD 12.5kΩ 125Ω 6kΩ COM SIX 14.3dB 900MHz AMPLIFIER STAGES NINE DETECTOR CELLS SPACED 14.3dB 6 01082-027 VPS 7 VPS COM S 2 Figure 27. Main Features of the AD8307 IE 2.4mA 01082-029 The differential current-mode outputs of the nine detectors are summed and then converted to single sided form in the output stage, nominally scaled 2 μA/dB. The logarithmic output voltage is developed by applying this current to an on-chip 12.5 kΩ resistor, resulting in a logarithmic slope of 25 mV/dB (that is, 500 mV/decade) at Pin OUT. This voltage is not buffered, allowing the use of a variety of special output interfaces, including the addition of post-demodulation filtering. The last detector stage includes a modification to temperature stabilize the log intercept, which is accurately positioned to make optimal use of the full output voltage range available. The intercept can be adjusted using the INT pin, which adds or subtracts a small current to the signal current. tolerance is typically within ±20%. Similarly, the capacitors have a typical tolerance of ±15% and essentially zero temperature or voltage sensitivity. Most interfaces have additional small junction capacitances associated with them, due to active devices or ESD protection; these can be neither accurate nor stable. Component numbering in each of these interface diagrams is local. 01082-028 The AD8307 comprises six main amplifier/limiter stages, each having a gain of 14.3 dB and small signal bandwidth of 900 MHz; the overall gain is 86 dB with a −3 dB bandwidth of 500 MHz. These six cells, and their associated gm styled full wave detectors, handle the lower two-thirds of the dynamic range. Three top end detectors, placed at 14.3 dB taps on a passive attenuator, handle the upper third of the 90 dB range. Biasing for these cells is provided by two references: one determines their gain; the other is a band gap circuit that determines the logarithmic slope and stabilizes it against supply and temperature variations. The AD8307 can be enabled/ disabled by a CMOS-compatible level at ENB (Pin 6). The first amplifier stage provides a low voltage noise spectral density (1.5 nV/√Hz). COM The last gain stage also includes an offset sensing cell. This generates a bipolarity output current when the main signal path has an imbalance due to accumulated dc offsets. This current is integrated by an on-chip capacitor (which can be increased in value by an off-chip component at OFS). The resulting voltage is used to null the offset at the output of the first stage. Since it does not involve the signal input connections, whose ac-coupling capacitors otherwise introduce a second pole in the feedback path, the stability of the offset correction loop is assured. The AD8307 is built on an advanced, dielectrically isolated, complementary bipolar process. Most resistors are thin film types having a low temperature coefficient of resistance (TCR) and high linearity under large signal conditions. Their absolute Figure 29. Signal Input Interface INPUT INTERFACE Figure 29 shows the essentials of the signal input interface. CP and CM are the parasitic capacitances to ground; CD is the differential input capacitance, mostly due to Q1 and Q2. In most applications, both input pins are ac-coupled. The switches close when Enable is asserted. When disabled, the inputs float, bias current IE is shut off, and the coupling capacitors remain charged. If the log amp is disabled for long periods, small leakage currents discharge these capacitors. If they are poorly matched, charging currents at power-up can generate a Rev. C | Page 14 of 24 AD8307 In most applications, the signal is single sided and can be applied to either Pin 1 or Pin 8, with the other pin ac-coupled to ground. Under these conditions, the largest input signal that can be handled by the AD8307 is 10 dBm (sine amplitude of ±1 V) when operating from a 3 V supply; 16 dBm can be handled using a 5 V supply. The full 16 dBm can be achieved for supplies down to 2.7 V, using a fully balanced drive. For frequencies above about 10 MHz, this is most easily achieved using a matching network. Using such a network, having an inductor at the input, the input transient is eliminated. Occasionally, it is desirable to use the dc-coupled potential of the AD8307. The main challenge here is to present signals to the log amp at the elevated common-mode input level, requiring the use of low noise, low offset buffer amplifiers. Using dual supplies of ±3 V, the input pins can operate at ground potential. OFFSET INTERFACE The input referred dc offsets in the signal path are nulled via the interface associated with Pin 3, shown in Figure 30. Q1 and Q2 are the first stage input transistors, with their corresponding load resistors (125 Ω). Q3 and Q4 generate small currents, which can introduce a dc offset into the signal path. When the voltage on OFS is at about 1.5 V, these currents are equal, and nominally 64 μA. When OFS is taken to ground, Q4 is off and the effect of the current in Q3 is to generate an offset voltage of 64 μV × 125 Ω = 8 mV. Since the first stage gain is ×5, this is equivalent to a input offset (INP to INM) of 1.6 mV. When OFS is taken to its most positive value, the input referred offset is reversed to −1.6 mV. If true dc coupling is needed, down to very small inputs, this automatic loop must be disabled, and the residual offset eliminated using a manual adjustment. In normal operation, however, using an ac-coupled input signal, the OFS pin should be left open. Any residual input offset voltage is then automatically nulled by the action of the feedback loop. The gm cell, which is gated off when the chip is disabled, converts any output offset (sensed at a point near the end of the cascade of amplifiers) to a current. This is integrated by the on-chip capacitor CHP, and any added external capacitance COFS, so as to generate an error voltage, which is applied back to the input stage in the polarity needed to null the output offset. From a small signal perspective, this feedback alters the response of the amplifier, which, rather than behaving as a fully dc-coupled system, now exhibits a zero in its ac transfer function, resulting in a closed loop high-pass corner at about 1.5 MHz. 7 125Ω INPUT STAGE MAIN GAIN STAGES Q1 Q2 BIAS, ~1.2V VPS 125Ω 64µA AT BALANCE S OFS Q3 36kΩ Q4 3 48kΩ COFS TO LAST DETECTOR gm AVERAGE ERROR CURRENT CHP 2 COM 01082-030 transient input voltage that can block the lower reaches of the dynamic range until it has become much less than the signal. Figure 30. Offset Interface and Offset Nulling Path The offset feedback is limited to a range of ±1.6 mV; signals larger than this override the offset control loop, which only affects performance for very small inputs. An external capacitor reduces the high-pass corner to arbitrarily low frequencies; using 1 μF this corner is below 10 Hz. All ADI log amps use an offset nulling loop; the AD8307 differs in using this single sided form. OUTPUT INTERFACE The outputs from the nine detectors are differential currents, having an average value that is dependent on the signal input level, plus a fluctuation at twice the input frequency. The currents are summed at nodes LGP and LGM in Figure 31. Further currents are added at these nodes, to position the intercept, by slightly raising the output for zero input, and to provide temperature compensation. Since the AD8307 is not laser trimmed, there is a small uncertainty in both the log slope and the log intercept. These scaling parameters can be adjusted. For zero signal conditions, all the detector output currents are equal. For a finite input of either polarity, their difference is converted by the output interface to a single sided unipolar current nominally scaled 2 μA/dB (40 μA/decade), at Pin OUT. An on-chip 12.5 kΩ resistor, R1, converts this current to a voltage of 25 mV/dB. C1 and C2 are effectively in shunt with R1 and form a low-pass filter pole with a corner frequency of about 5 MHz. The pulse response settles to within 1% of the final value within 300 ns. This integral low-pass filter provides adequate smoothing in many IF applications. At 10.7 MHz, the 2f ripple is 12.5 mV in amplitude, equivalent to ±0.5 dB, and only 0.5 mV (±0.02 dB) at f = 50 MHz. A filter capacitor CFLT added from Pin OUT to ground lowers this corner frequency. Using 1 μF, the ripple is maintained to less than ±0.5 dB down to input frequencies of 100 Hz. Note that COFS should also be increased in low frequency applications, and is typically made equal to CFLT. Rev. C | Page 15 of 24 AD8307 3pF LGP 2µA/dB 0–220µA 25mV/dB OUT 4 Rev. C | Page 16 of 24 1.25kΩ CFLT 60kΩ 1.25kΩ C2 1pF C1 2.5pF 7 VPS 5 INT 2 COM 8.25kΩ ~400mV FROM ALL DETECTORS LGM Note that while the AD8307 can operate down to supply voltages of 2.7 V, the output voltage limit is reduced when the supply drops below 4 V. This characteristic is the result of necessary headroom requirements, approximately two VBE drops, in the design of the output stage. 1.25kΩ R1 12.5kΩ 1.25kΩ BIAS 60µA Figure 31. Simplified Output Interface 01082-031 It can be desirable to increase the speed of the output response, with the penalty of increased ripple. One way to do this is simply by connecting a shunt load resistor from Pin OUT to ground, which raises the low-pass corner frequency. This also alters the logarithmic slope, for example to 7.5 mV/dB using a 5.36 kΩ resistor, while reducing the 10% to 90% rise time to 25 ns. The ripple amplitude for 50 MHz input remains 0.5 mV, but this is now equivalent to ±0.07 dB. If a negative supply is available, the output pin can be connected directly to the summing node of an external op amp connected as an inverting mode transresistance stage. AD8307 THEORY OF OPERATION Careful shielding is essential. A ground plane should be used to provide a low impedance connection to the common pin, COM, for the decoupling capacitor(s) used at VPS, and as the output ground. It is inadvisable to assume that the ground plane is an equipotential. Neither of the inputs should be ac-coupled directly to the ground plane, but should be kept separate from it, being returned instead to the low associated with the source. This can mean isolating the low side of an input connector with a small resistance to the ground plane. the log amp side of the coupling capacitors; in the former case, smaller capacitors can be used for a given frequency range; in the latter case, the effective RIN is lowered directly at the log amp inputs. Figure 33 shows the output versus the input level, in dBm, when driven from a terminated 50 Ω generator, for sine inputs at 10 MHz, 100 MHz, and 500 MHz; Figure 34 shows the typical logarithmic conformance under the same conditions. Note that +10 dBm corresponds to a sine amplitude of 1 V, equivalent to an rms power of 10 mW in a 50 Ω termination. However, if the termination resistor is omitted, the input power is negligible. The use of dBm to define input level therefore needs to be considered carefully in connection with the AD8307. 3.0 2.5 10MHz OUTPUT VOLTAGE (V) The AD8307 has very high gain and a bandwidth from dc to over 1 GHz, at which frequency the gain of the main path is still over 60 dB. Consequently, it is susceptible to all signals within this very broad frequency range that find their way to the input terminals. It is important to remember that these are indistinguishable from the wanted signal, and has the effect of raising the apparent noise floor (that is, lowering the useful dynamic range). For example, while the signal of interest can be an IF of 50 MHz, any of the following could easily be larger than the IF signal at the lower extremities of its dynamic range: 60 Hz hum (picked up due to poor grounding techniques); spurious coupling (from a digital clock source on the same PC board); local radio stations; and so on. BASIC CONNECTIONS 500MHz 4.7Ω 01082-033 –50 –40 –30 –20 –10 0 10 20 5 4 3 500MHz 2 VP, 2.7V TO 5.5V AT ~8mA 1 0 –1 10MHz 100MHz –2 7 6 –4 5 –5 –80 AD8307 –60 –50 –40 –30 –20 –10 0 10 20 Figure 34. Logarithmic Law Conformance at 10 MHz, 100 MHz, and 500 MHz 4 NC C2 = CC NC = NO CONNECT OUTPUT 25mV/dB INPUT MATCHING 01082-032 3 –70 INPUT LEVEL (dBm) INM COM OFS OUT 2 01082-034 –3 INP VPS ENB INT 1 –60 Figure 33. Log Response at 10 MHz, 100 MHz, and 500 MHz NC 8 –70 INPUT LEVEL (dBm) C1 = CC 1.1kΩ 100MHz 1.0 0 –80 ERROR (dB) 0.1µF RIN ≈ 1.5 0.5 Figure 32 shows the simple connections suitable for many applications. The inputs are ac coupled by C1 and C2, which should have the same value, say, CC. The coupling time constant is RIN CC/2, thus forming a high-pass corner with a 3 dB attenuation at fHP = 1/(pRINCC ). In high frequency applications, fHP should be as large as possible in order to minimize the coupling of unwanted low frequency signals. Conversely, in low frequency applications, a simple RC network forming a lowpass filter should be added at the input for the same reason. For the case where the generator is not terminated, the signal range should be expressed in terms of the voltage response, and extends from −85 dBV to +6 dBV. INPUT –75dBm TO +16dBm RT 2.0 Figure 32. Basic Connections Where it is necessary to terminate the source at a low impedance, the resistor RT should be added, with allowance for the shunting effect of the basic 1.1 kΩ input resistance (RIN) of the AD8307. For example, to terminate a 50 Ω source, a 52.3 Ω 1% tolerance resistor should be used. This can be placed on the input side or Where higher sensitivity is required, an input matching network is valuable. Using a transformer to achieve the impedance transformation also eliminates the need for coupling capacitors, which lowers the offset voltage generated directly at the input, and balances the drives to Pin INP and Pin INM. The choice of turns ratio depends somewhat on the frequency. At frequencies below 50 MHz, the reactance of the input capacitance is much higher than the real part of the input impedance. In this Rev. C | Page 17 of 24 AD8307 0.1µF frequency range, a turns ratio of about 1:4.8 lowers the input impedance to 50 Ω while raising the input voltage, thus lowering the effect of the short-circuit noise voltage by the same factor. There is a small contribution from the input noise current, so the total noise is reduced by a lesser factor. The intercept is also lowered by the turns ratio; for a 50 Ω match, it is reduced by 20 log10 (4.8) or 13.6 dB. 4.7Ω VP, 2.7V TO 5.5V AT ~8mA C1 NC 50Ω INPUT –88dBm TO +3dBm 8 7 6 5 INP VPS ENB INT LM AD8307 INM COM OFS OUT ZIN = 50Ω 1 2 3 4 NC NARROW-BAND MATCHING OUTPUT 25mV/dB Transformer coupling is useful in broadband applications. However, a magnetically-coupled transformer may not be convenient in some situations. At high frequencies, it is often preferable to use a narrow-band matching network, as shown in Figure 35. 01082-035 C2 NC = NO CONNECT Figure 35. High Frequency Input Matching Network 14 13 12 11 This has several advantages. The same voltage gain is achieved, providing increased sensitivity, but now a measure of selectivity is also introduced. The component count is low: two capacitors and an inexpensive chip inductor. Further, by making these capacitors unequal, the amplitudes at Pin INP and Pin INM can be equalized when driving from a single sided source; that is, the network also serves as a balun. GAIN 10 DECIBELS 9 8 7 6 5 4 3 INPUT 2 Figure 36 shows the response for a center frequency of 100 MHz. Note the very high attenuation at low frequencies. The high frequency attenuation is due to the input capacitance of the log amp. 01082-036 1 0 –1 60 70 80 90 100 110 120 130 140 150 FREQUENCY (MHz) Figure 36. Response of 100 MHz Matching Network Table 4 provides solutions for a variety of center frequencies (FC) and matching impedances (ZIN) of nominally 50 Ω and 100 Ω. The unequal capacitor values were chosen to provide a well balanced differential drive, and to allow better centering of the frequency response peak when using standard value components; this generally results in a ZIN that is not exact. The full AD8307 HF input impedance and the inductor losses are included in the modeling. Table 4. Narrow-Band Matching Values FC (MHz) 10 20 50 100 150 200 250 500 10 20 50 100 150 200 250 500 ZIN (Ω) 45 44 46 50 57 57 50 54 103 102 99 98 101 95 92 114 C1 (pF) 160 82 30 15 10 7.5 6.2 3.9 100 51 22 11 7.5 5.6 4.3 2.2 C2 (pF) 150 75 27 13 8.2 6.8 5.6 3.3 91 43 18 9.1 6.2 4.7 3.9 2.0 Rev. C | Page 18 of 24 LM (nH) 3300 1600 680 330 220 150 100 39 5600 2700 1000 430 260 180 130 47 Voltage Gain (dB) 13.3 13.4 13.4 13.4 13.2 12.8 12.3 10.9 10.4 10.4 10.6 10.5 10.3 10.3 9.9 6.8 AD8307 SLOPE AND INTERCEPT ADJUSTMENTS ΔdB = 20 log10 1+ M 1− M The log intercept is adjustable over a ±3 dB range, which is sufficient to absorb the worst-case intercept error in the AD8307, plus some system level errors. For greater range, set RS to zero. VR2 is adjusted while applying an accurately known CW signal near the lower end of the dynamic range in order to minimize the effect of any residual uncertainty in the slope. For example, to position the intercept to −80 dBm, a test level of −65 dBm can be applied and VR2 adjusted to produce a dc output of 15 dB above zero at 25 mV/dB, which is +0.3 V. (7) 0.1µF VR2 50kΩ C1 = CC Rev. C | Page 19 of 24 VP, 2.7V TO 5.5V AT ~8mA RS ±3dB 8 INPUT –75dBm TO +16dBm 7 6 5 INP VPS ENB INT AD8307 FOR VP = 3V, RS = 20kΩ VP = 5V, RS = 51kΩ INM COM OFS OUT 1 For example, using an rms signal level of −40 dBm with a 70% modulation depth (M = 0.7), the decibel range is 15 dB, as the signal varies from −47.5 dBm to −32.5 dBm. 4.7Ω 2 3 4 NC C2 = CC NC = NO CONNECT 20mV/dB ±10% 32.4kΩ VR1 50kΩ Figure 37. Slope and Intercept Adjustments 01082-037 Where higher calibration accuracy is needed, the adjustments shown in Figure 37 can be used, either singly or in combination. The log slope is lowered to 20 mV/dB by shunting the nominally 12.5 kΩ on-chip load resistor (see Figure 31) with 50 kΩ, adjusted by VR1. The calibration range is ±10% (18 mV/dB to 22 mV/dB), including full allowance for the variability in the value of the internal load. The adjustment can be made by alternately applying two input levels, provided by an accurate signal generator, spaced over the central portion of the log amp’s dynamic range, for example −60 dBm and 0 dBm. An AM modulated signal, at the center of the dynamic range, can also be used. For a modulation depth M, expressed as a fraction, the decibel range between the peaks and troughs over one cycle of the modulation period is given by AD8307 INPUT –75dBm TO +16dBm VP, 2.7V TO 5.5V VR2 50kΩ RS ±3dB INPUT –75dBm TO +16dBm 6 5 INP VPS ENB INT FOR VP = 3V, RS = 20kΩ VP = 5V, RS = 51kΩ INM COM OFS OUT 2 3 NC 25mV/dB AD8031 AD8307 4 20mV/dB 2 3 4 NC = NO CONNECT In Figure 40, the capacitor values are chosen for operation in the audio field, providing a corner frequency of 10 Hz, an attenuation of 80 dB/decade above this frequency, and a 1% settling time of 150 ms (0.1% in 175 ms). The residual ripple is 4 mV (±0.02 dB) when the input to the AD8307 is at 20 Hz. This filter can easily be adapted to other frequencies by proportional scaling of C5 to C7 (for example, for 100 kHz use 100 pF). Placed ahead of a digital multimeter, the convenient slope scaling of 100 mV/dB requires only a repositioning of the decimal point to read directly in decibels. The supply voltage for the filter must be large enough to support the dynamic range; a minimum of 9 V is needed for most applications; 12 V is recommended. 4.7Ω R1 50kΩ VP VR1 2kΩ C1 10µF R2 30.1kΩ R1 20kΩ COM R1 2kΩ COM 8 7 6 OP AMP IS AD8032 SCALE C1 TO C8 AS NEEDED. NOTE POLARITIES IF TANTALUM CAPACITORS ARE USED. 422Ω INT ±4dB + 5 C5 1µF C8 7.32kΩ 1µF + + INP VPS ENB INT C3 2.5nF Figure 38. Log Amp with Buffered Output INM COM OFS OUT 1 C1 is optional; it lowers the corner frequency of the low-pass output filter. A value of 0.1 μF should be used for applications in which the output is measured on a voltmeter or other low speed device. On the other hand, when C1 is omitted, the 10% to 90% response time is under 200 ns and is typically 300 ns to 99% of final value. To achieve faster response times, it is necessary to lower the load resistance at the output of the AD8307, then restore the scale using a higher gain in the op amp. Using 8.33 kΩ, the basic slope is 10 mV/dB; this can be restored to 25 mV/dB using a buffer gain of 2.5. The overall 10% to 90% response time is under 100 ns. Figure 39 shows how the output current capability can be augmented to drive a 50 Ω load; RT optionally provides reverse termination, which halves the slope to 12.5 mV/dB. FOUR POLE FILTER In low frequency applications, for example, audio down to 20 Hz, it is useful to employ the buffer amplifier as a multipole low-pass filter in order to achieve low output ripple while maintaining a rapid response time to changes in signal level. 2 3 + + C2 10µF OUTPUT 100mV/dB 100kΩ AD8307 C4 1µF C1 OUTPUT 50Ω MINIMUM Figure 39. Cable Driving Log Amp INPUT 5mV TO 160V rms 0.1µF 01082-038 32.4kΩ VR1 50kΩ RT (OPTIONAL) R2 3.01kΩ 10mV/dB ±18% 6.34kΩ VR1 5kΩ NC NC = NO CONNECT 2N3904 5 NC OUTPUT 50mV/dB ±10% AD8031 AD8307 1 6 INP VPS ENB INT 1 4.7Ω 7 7 INM COM OFS OUT The output can be buffered, and the slope optionally increased, using an op amp. If the single-supply capability is to be preserved, a suitable component is the AD8031. Like the AD8307, it is capable of operating from a 2.7 V supply and features a rail-torail output capability; it is available in a 5-lead version and in dual form as the 8-lead AD8032. Figure 38 shows how the slope can be increased to 50 mV/dB (1 V per decade), requiring a 5 V supply (90 dB times 50 mV is a 4.5 V swing). VR1 provides a ±10% slope adjustment; VR2 provides a ±3 dB intercept range. With R2 = 4.99 kΩ, the slope is adjustable to 25 mV/dB, allowing the use of a 2.7 V supply. Setting R2 to 80.6 kΩ, it is raised to 100 mV/dB, providing direct reading in decibels on a digital voltmeter. Since a 90 dB range now corresponds to a 9 V swing, a supply of at least this amount is needed for the op amp. 8 RS ±3dB 8 BUFFERED OUTPUT 0.1µF VP, 2.7V TO 5.5V VR2 50kΩ 93kΩ 34kΩ 4 34kΩ VR2 50kΩ SLOPE C6 + 32.4kΩ 1µF C7 + 1µF 75kΩ 80.6kΩ COM 01082-040 The AD8307 is a highly versatile and easily applied log amp requiring very few external components. Most applications of this product can be accommodated using the simple connections shown in the preceding section. 4.7Ω 01082-039 0.1µF APPLICATIONS INFORMATION Figure 40. Log Amp with Four Pole Low Pass Filter Figure 40 also shows the use of an input attenuator that can optionally be employed here, or in any other of these applications, to produce a useful wide range ac voltmeter with direct decibel scaling. The basic range of −73 dBm to +17 dBm (that is, 50 μV rms to 1.6 V rms, for sine excitations) is shifted for illustrative purposes to 5 mV to 160 V rms (at which point the power in R1 is 512 mW). Because the basic input resistance of the AD8307 is not precise, VR1 is used to center the signal range at its input, doubling as a ±4 dB intercept adjustment. The low frequency response extends to 15 Hz; a higher corner frequency can be selected as needed by scaling C1 and C2. The shunt capacitor C3 is used to lower the high frequency bandwidth to about 100 kHz, and thus lower the susceptibility to spurious signals. Other values should be chosen as needed for the coupling and filter capacitors. Rev. C | Page 20 of 24 AD8307 The front-end adaptation shown in Figure 41 provides the measurement of power being delivered from a transmitter final amplifier to an antenna. The range has been set to cover the power range −30 dBm (7.07 mV rms, or 1 μW) to +60 dBm (223 V rms, or 1 kW). A nominal voltage attenuation ratio of 158:1 (44 dB) is used; thus the intercept is moved from −84 dBm to −40 dBm and the AD8307, scaled 0.25 V/decade of power, now reads 1.5 V for a power level of 100 mW, 2.0 V at 10 W and 2.5 V at 1 kW. The general expression is P (dBm) = 40 (VOUT − 1) The required attenuation could be implemented using a capacitive divider, providing a very low input capacitance, but it is difficult to ensure accurate values of small capacitors. A better approach is to use a resistive divider, taking the required precautions to minimize spurious coupling into the AD8307 by placing it in a shielded box, with the input resistor passing through a hole in this box, as indicated in Figure 41. The coupling capacitors shown here are suitable for f ≥ 10 MHz. A capacitor can be added across the input pins of the AD8307 to reduce the response to spurious HF signals, which, as already noted, extends to over 1 GHz. The mismatch caused by the loading of this resistor is trivial; only 0.05% of the power delivered to the load is absorbed by the measurement system, a maximum of 500 mW at 1 kW. The post-demodulation filtering and slope calibration arrangements are chosen from other applications described in this data sheet to meet the particular system requirements. The 1 nF capacitor lowers the risk of HF signals entering the AD8307 via the load. TO ANTENNA 100kΩ 1/2W 0.1µF VP 22Ω 51pF +5V NC 7 6 5 INP VPS ENB INT 604Ω INM COM OFS OUT AD8307 1 2 3 4 NC 51pF 1nF LEADTHROUGH CAPACITORS, 1nF 2kΩ VOUT OUTPUT NC = NO CONNECT 01082-041 50Ω INPUT FROM P.A. 1µW TO 1kW 8 VR1 2kΩ INT ±3dB Figure 41. 1 μW to 1 kW 50 Ω Power Meter MEASUREMENT SYSTEM WITH 120 dB DYNAMIC RANGE The dynamic range of the AD8307 can be extended further— from 90 dB to over 120 dB—by the addition of an X-AMP® such as the AD603. This type of variable gain amplifier exhibits a very exact exponential gain control characteristic, which is another way of stating that the gain varies by a constant number of decibels for a given change in the control voltage. For the AD603, this scaling factor is 40 dB/V, or 25 mV/dB. It is apparent that this property of a linear-in-dB response is characteristic of log amps; indeed, the AD8307 exhibits the same scaling factor. The AD603 has a very low input referred noise: 1.3 nV/√Hz at its 100 Ω input, or 0.9 nV/√Hz when matched to 50 Ω, equivalent to 0.4 μV rms, or −115 dBm, in a 200 kHz bandwidth. It is also capable of handling inputs in excess of 1.4 V rms, or +16 dBm. It is thus able to cope with a dynamic range of over 130 dB in this particular bandwidth. Now, if the gain control voltage for the X-AMP is derived from the output of the AD8307, the effect is to raise the gain of this frontend stage when the signal is small and lower it when it is large, but without altering the fundamental logarithmic nature of the response. This gain range is 40 dB, which, combined with the 90 dB range of the AD8307, again corresponds to a 130 dB range. 50Ω INPUT –105dBm TO +15dBm L1 750nH C1 150pF VP, +5V R1 187kΩ R2 28kΩ BANDPASS FILTER* 4.7Ω 0.1µF 0.65V NC 1 VPOS 8 GPOS 2 GNEG 3 VINP 4 COMM FDBK 5 R3 330Ω VOUT 7 R4 464Ω AD603 VNEG 6 VR1 5kΩ INT ±8dB VN, –5V R5 100kΩ 8 7 6 5 INP VPS ENB INT AD8307 INM COM OFS OUT 1 2 3 4 NC 1nF R6 20kΩ 0.3V TO 2.3V R7 80.6kΩ 0.15V TO 1.15V *FOR EXAMPLE: MURATA SFE10.7MS2G-A NC = NO CONNECT OUTPUT 10mV/dB 01082-042 1 μW TO 1 kW 50 Ω POWER METER Figure 42. 120 dB Measurement System Figure 42 shows how these two parts can work together to provide state-of-the-art IF measurements in applications such as spectrum/network analyzers and other high dynamic range instrumentation. To understand the operation, note first that the AD8307 is used to generate an output of about 0.3 V to 2.3 V. This 2 V span is divided by 2 in R5/R6/R7 to provide the 1 V span needed by the AD603 to vary its gain by 40 dB. Note that an increase in the positive voltage applied at GNEG (Pin 2 of AD603) lowers the gain. This feedback network is tapped to provide a convenient 10 mV/dB scaling at the output node, which can be buffered if necessary. The center of the voltage range fed back to the AD603 is 650 mV, and the ±20 dB gain range is centered by R1/R2. Note that the intercept calibration of this system benefits from the use of a well regulated 5 V supply. To absorb the insertion loss of the filter and center the full dynamic range, the intercept is adjusted by varying the maximum gain of the AD603, using VR1. Figure 43 shows the AD8307 output over the range −120 dBm to +20 dBm and the deviation from an ideal logarithmic response. The dotted line shows the increase in the noise floor that results when the filter is omitted; the decibel difference is about 10 log10(50/0.2) or 24 dB, assuming a 50 MHz bandwidth from the AD603. An L-C filter can be used in place of the ceramic filter used in this example. Rev. C | Page 21 of 24 AD8307 2.50 See Figure 40 for a more elaborate filter. To improve the law conformance at very low signal levels and at low frequencies, add C4 to the offset compensation loop. 2.25 1 1.25 0 –1 ERROR (WITH FILTER) 0.75 0.50 VIN 0.5mV TO 20V SINE AMPLITUDE –2 C3 750pF –80 –60 –40 –20 INPUT LEVEL (dBm) 0 20 2 C4 1µF C5 1µF VOUT 25mV/dB DC-COUPLED APPLICATIONS It may occasionally be necessary to provide response to dc inputs. Since the AD8307 is internally dc-coupled, there is no fundamental reason why this is precluded. However, there is a practical constraint since its inputs must be positioned about 2 V above the COM potential for proper biasing of the first stage. If the source is a differential signal at this level, it can be directly connected to the input. For example, a microwave detector can be ac-coupled at its RF input and its baseband load then automatically provided by the floating RIN and CIN of the AD8307, at about VP/2. Usually, the source is a single sided ground-referenced signal; thus, it is necessary to provide a negative supply for the AD8307. This can be achieved as shown in Figure 45. The output is now referenced to this negative supply, and it is necessary to provide an output interface that performs a differential-to-single sided conversion. This is the purpose of the AD830. The slope can be arranged to be 20 mV/dB, when the output ideally runs from zero, for a dc input of 10 μV, to 2.2 μV, for an input of 4 V. The device is fundamentally insensitive to the sign of the input signal, but with this biasing scheme, the maximum negative input is constrained to about −1.5 V. The transfer function after trimming and with R7 = 0 is VOUT = (0.4 V) log10 (VIN/10 μV) R1 4.7Ω C1 0.1µF R2 3.3kΩ +5V FOR 20mV/dB +10V FOR 50mV/dB +15V FOR 100mV/dB VR2 50kΩ 8 7 6 R5* 5 8 VP INP VPS ENB INT INM COM OFS OUT 1 2 3 7 6 INT NC 5 VN AD830 AD8307 C1 1µF 4 VOUT –5V X1 X2 Y1 Y2 1 2 3 4 R7 20mV/dB R3 1kΩ 4 Figure 44. Connections for Low Frequency Operation A high-pass 3 dB corner frequency of nominally 3 Hz is set by the 10 μF coupling capacitors C1 and C2, which are preferably tantalum electrolytics (note the polarity) and a low-pass 3 dB corner frequency of 200 kHz (set by C3 and the effective resistance at the input of 1 kΩ). The −1% amplitude error points occur at 20 Hz and 30 kHz. These are readily altered to suit other applications by simple scaling. When C3 is zero, the low-pass corner is at 200 MHz. Note that the lower end of the dynamic range is improved by this capacitor, which essentially provides an HF short circuit at the input. This significantly lowers the wideband noise; the noise reduction is about 2 dB compared to when the AD8307 is driven from a 50 Ω source. Ensure that the output is free of postdemodulation ripple by lowering the low-pass filter time constant. This is provided by C5; with the value shown in Figure 44, the output time constant is 125 ms. AD589 3 NC = NO CONNECT The AD8307 provides excellent logarithmic conformance at signal frequencies that can be arbitrarily low, depending only on the values used for the input coupling capacitors. It can also be desirable to add a low-pass input filter in order to desensitize the log amp to HF signals. Figure 44 shows a simple arrangement, providing coupling with an attenuation of 20 dB; the intercept is shifted up by this attenuation, from −84 dBm to −64 dBm, and the input range is now 0.5 mV to 20 V (sine amplitude). TEMP 5 AD8307 1 OPERATION AT LOW FREQUENCIES VIN 6 INP VPS ENB INT + R2 C2 10µF 5kΩ Figure 43. Results for 120 dB Measurement System +5V NC 7 INM COM OFS OUT 01082-043 –100 4.7Ω 0.1µF 8 WITH FILTER 0.25 0 C1 R1 10µF 5kΩ + VR1 2kΩ Q1 2N3904 NC = NO CONNECT C3 0.1µF –2V R6 32.4kΩ VR3 50kΩ R8 R9 250Ω –5V *51kΩ FOR 20mV/dB; 5kΩ FOR 100mV/dB Figure 45. Connections for DC-Coupled Applications Rev. C | Page 22 of 24 01082-044 VOUT (V) 1.50 1.00 5V 2 01082-045 WITHOUT FILTER 1.75 ERROR (dB) 2.00 AD8307 The intercept can be raised, for example, to 100 μV, with the rationale that the dc precision does not warrant operation in the first decade (from 10 μV to 100 μV). Likewise, the slope can be raised to 50 mV/dB, using R7 = 3 kΩ, R8 = 2 kΩ , or to 100 mV/dB, to simplify decibel measurements on a DVM, using R7 = 8 kΩ, R8 = 2 kΩ, which raises the maximum output 11 V, thus requiring a 15 V supply for the AD830. The output can be made to swing in a negative direction by simply reversing Pins 1 and 2. Low-pass filtering capacitor, C3, sets the output rise time to about 1 ms. 6.0 5.5 5.0 4.0 1.0 3.5 0.5 3.0 0 2.5 –0.5 2.0 –1.0 ERROR (dB) 1.5 OPERATION ABOVE 500 MHZ 0.5 100µ 1m 10m 100m 1 10 VIN Figure 46. Ideal Output and Law-Conformance Error for the DC-Coupled AD8307 at 50 mV/dB Figure 46 shows the output and the law-conformance error, in the absence of noise and input offset, for the 50 mV/dB option. Note that the error ripple for dc excitation is about twice that for the more usual sinusoidal excitation. In practice, both the noise and the internal offset voltage degrade the accuracy in the first decade of the dynamic range. The latter is now manually nulled by VR1, using a simple method that ensures very low residual offsets. A temporary ac signal, typically a sine wave of 100 mV in amplitude at a frequency of about 100 Hz, is applied via the capacitor at node TEMP; this has the effect of disturbing the offset nulling voltage. The output voltage is then viewed on an oscilloscope and VR1 is adjusted until the peaks of the (frequency-doubled) waveform are exactly equal in amplitude. This procedure can provide an input null down to about 10 μV. The temperature drift is very low, though not specified since the AD8307 is not principally designed to operate as a baseband log amp; in ac modes, this offset is nulled continuously and automatically. The AD8307 is not intended for use above 500 MHz. However, it does provide useful performance at higher frequencies. Figure 47 shows a plot of the logarithmic output of the AD8307 for an input frequency of 900 MHz. The device shows good logarithmic conformance from −50 dBm to −10 dBm. There is a bump in the transfer function at −5 dBm, but if this is acceptable, the device is usable over a 60 dB dynamic range (−50 dBm to +10 dBm). 2.0 1.8 1.6 1.4 Rev. C | Page 23 of 24 1.2 1.0 0.8 0.6 0.4 01082-047 01082-046 1.0 0 10µ Finally, the slope must be adjusted. This can be performed by applying a low frequency square wave to the main input, having precisely determined upper and lower voltage levels, provided by a programmable waveform generator. A suitable choice is a 100 Hz square wave with levels of 10 mV and 1 V. The output is a low-pass filtered square wave, and its amplitude should be 0.8 V for 20 mV/dB scaling, or 4 V for 100 mV/dB scaling. VOUT (V) VOUT (V) 4.5 Next, it is necessary to set the intercept. This is the purpose of VR2, which should be adjusted after VR1. The simplest method is to short the input and adjust VR2 for an output of 0.3 V, corresponding to the noise floor. For more exacting applications, a temporary sinusoidal test voltage of 1 mV in amplitude, at about 1 MHz, should be applied, which can require the use of a temporary on-board input attenuator. For 20 mV/dB scaling, a 10 μV dc intercept (which is 6 dB below the ac intercept) requires adjusting the output to 0.68 V; for 100 mV/dB scaling, this becomes 3.4 V. If a 100 μV intercept is preferred (usefully lowering the maximum output voltage), these become 0.28 V and 1.4 V, respectively. 0.2 0 –60 –50 –40 –30 –20 PIN (dBm) –10 0 10 Figure 47. Output vs. Input Level for a 900 MHz Input Signal AD8307 OUTLINE DIMENSIONS 0.400 (10.16) 0.365 (9.27) 0.355 (9.02) 8 5 1 0.280 (7.11) 0.250 (6.35) 0.240 (6.10) 4 0.100 (2.54) BSC 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.060 (1.52) MAX 0.210 (5.33) MAX 0.015 (0.38) MIN 0.150 (3.81) 0.130 (3.30) 0.115 (2.92) SEATING PLANE 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.195 (4.95) 0.130 (3.30) 0.115 (2.92) 0.015 (0.38) GAUGE PLANE 0.430 (10.92) MAX 0.005 (0.13) MIN 0.014 (0.36) 0.010 (0.25) 0.008 (0.20) 0.070 (1.78) 0.060 (1.52) 0.045 (1.14) 070606-A COMPLIANT TO JEDEC STANDARDS MS-001 CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS. Figure 48. 8-Lead Plastic Dual In-Line Package [PDIP] (N-8) Dimensions shown in inches and (millimeters) 5.00 (0.1968) 4.80 (0.1890) 8 1 5 4 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) COPLANARITY 0.10 SEATING PLANE 6.20 (0.2440) 5.80 (0.2284) 1.75 (0.0688) 1.35 (0.0532) 0.51 (0.0201) 0.31 (0.0122) 0.50 (0.0196) 0.25 (0.0099) 45° 8° 0° 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-012-A A CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. 060506-A 4.00 (0.1574) 3.80 (0.1497) Figure 49. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in millimeters and (inches) ORDERING GUIDE Model AD8307AN AD8307ANZ1 AD8307AR AD8307AR-REEL AD8307AR-REEL7 AD8307ARZ1 AD8307ARZ-REEL1 AD8307ARZ-RL71 Temperature Range −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C −40°C to +85°C Package Description 8-Lead PDIP 8-Lead PDIP 8-Lead SOIC_N 8-Lead SOIC_N 13" REEL 8-Lead SOIC_N 7" REEL 8-Lead SOIC_N 8-Lead SOIC_N 13" REEL 8-Lead SOIC_N 7" REEL 1 Z = Pb-free part. ©2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D01082-0-10/06(C) Rev. C | Page 24 of 24 Package Option N-8 N-8 R-8 R-8 R-8 R-8 R-8 R-8