Octal LNA/VGA/AAF/ADC and Crosspoint Switch AD9273 LOSW-C LO-C LI-C LG-C LOSW-D LO-D LI-D LG-D LOSW-E LO-E LI-E LG-E LOSW-F LO-F LI-F LG-F LOSW-G LO-G LI-G LG-G LNA AAF LNA VGA AAF LNA VGA AAF LNA VGA AAF LNA VGA AAF LNA VGA AAF LNA VGA AAF LOSW-H LO-H LI-H LG-H PDWN STBY VGA LNA VGA AAF 12-BIT ADC SERIAL LVDS DOUTA+ DOUTA– 12-BIT ADC SERIAL LVDS DOUTB+ DOUTB– 12-BIT ADC SERIAL LVDS DOUTC+ DOUTC– 12-BIT ADC SERIAL LVDS DOUTD+ DOUTD– 12-BIT ADC SERIAL LVDS DOUTE+ DOUTE– 12-BIT ADC SERIAL LVDS DOUTF+ DOUTF– 12-BIT ADC SERIAL LVDS DOUTG+ DOUTG– 12-BIT ADC SERIAL LVDS DOUTH+ DOUTH– REFERENCE SWITCH ARRAY DATA RATE MULTIPLIER LOSW-B LO-B LI-B LG-B AD9273 SERIAL PORT INTERFACE LOSW-A LO-A LI-A LG-A DRVDD FUNCTIONAL BLOCK DIAGRAM AVDD2 8 channels of LNA, VGA, AAF, and ADC Low noise preamplifier (LNA) Input-referred noise voltage = 1.2 nV/√Hz (gain = 21.3 dB) @ 5 MHz typical SPI-programmable gain = 15.6 dB/17.9 dB/21.3 dB Single-ended input; VIN maximum = 733 mV p-p/ 550 mV p-p/367 mV p-p Dual-mode active input impedance matching Bandwidth (BW) > 100 MHz Full-scale (FS) output = 4.4 V p-p differential Variable gain amplifier (VGA) Attenuator range = −42 dB to 0 dB SPI-programmable PGA gain = 21 dB/24 dB/27 dB/30 dB Linear-in-dB gain control Antialiasing filter (AAF) Programmable 2nd-order low-pass filter (LPF) from 8 MHz to 18 MHz Programmable high-pass filter (HPF) Analog-to-digital converter (ADC) 12 bits at 10 MSPS to 50 MSPS SNR = 70 dB SFDR = 75 dB Serial LVDS (ANSI-644, IEEE 1596.3 reduced range link) Data and frame clock outputs Includes an 8 × 8 differential crosspoint switch to support continuous wave (CW) Doppler Low power, 109 mW per channel at 12 bits/40 MSPS (TGC) 70 mW per channel in CW Doppler Flexible power-down modes Overload recovery in <10 ns Fast recovery from low power standby mode, <2 μs 100-lead TQFP AVDD1 FEATURES FCO+ FCO– DCO+ DCO– The AD9273 is designed for low cost, low power, small size, and ease of use. It contains eight channels of a low noise preamplifier (LNA) with a variable gain amplifier (VGA); an antialiasing filter (AAF); and a 12-bit, 10 MSPS to 50 MSPS analog-todigital converter (ADC). Each channel features a variable gain range of 42 dB, a fully differential signal path, an active input preamplifier termination, a maximum gain of up to 52 dB, and an ADC with a conversion rate of up to 50 MSPS. The channel is optimized for dynamic performance and low power in applications where a small package size is critical. CLK+ CLK– SDIO CSB SCLK VREF RBIAS GAIN– 07030-001 GENERAL DESCRIPTION GAIN+ Medical imaging/ultrasound Automotive radar CWD[7:0]+ AND CWD[7:0]– APPLICATIONS Figure 1. The LNA has a single-ended-to-differential gain that is selectable through the SPI. The LNA input-referred noise voltage is typically 1.2 nV/√Hz at a gain of 21.3 dB, and the combined input-referred noise voltage of the entire channel is 1.4 nV/√Hz at maximum gain. Assuming a 15 MHz noise bandwidth (NBW) and a 21.3 dB LNA gain, the input SNR is about 91 dB. In CW Doppler mode, the LNA output drives a transconductance amp that is switched through an 8 × 8 differential crosspoint switch. The switch is programmable through the SPI. Rev. Sp0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2008 Analog Devices, Inc. All rights reserved. AD9273 NOTES ©2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D07030F-0-10/08(Sp0) Rev. Sp0 | Page 2 of 2