ADC0820 ADC0820 8-Bit High Speed µP Compatible A/D Converter with Track/Hold Function Literature Number: SNAS529B ADC0820 8-Bit High Speed µP Compatible A/D Converter with Track/Hold Function General Description Features By using a half-flash conversion technique, the 8-bit ADC0820 CMOS A/D offers a 1.5 µs conversion time and dissipates only 75 mW of power. The half-flash technique consists of 32 comparators, a most significant 4-bit ADC and a least significant 4-bit ADC. The input to the ADC0820 is tracked and held by the input sampling circuitry eliminating the need for an external sample-and-hold for signals moving at less than 100 mV/µs. For ease of interface to microprocessors, the ADC0820 has been designed to appear as a memory location or I/O port without the need for external interfacing logic. n n n n n n n Key Specifications j Resolution 8 Bits j Conversion Time n n 2.5 µs Max (RD Mode) 1.5 µs Max (WR-RD Mode) j Low Power 75 mW Max j Total Unadjusted n n n n n n Built-in track-and-hold function No missing codes No external clocking Single supply — 5 VDC Easy interface to all microprocessors, or operates stand-alone Latched TRI-STATE output Logic inputs and outputs meet both MOS and T2L voltage level specifications Operates ratiometrically or with any reference value equal to or less than VCC 0V to 5V analog input voltage range with single 5V supply No zero or full-scale adjust required Overflow output available for cascading 0.3" standard width 20-pin DIP 20-pin molded chip carrier package 20-pin small outline package 20-pin shrink small outline package (SSOP) ± 1⁄2 LSB and ± 1 LSB Error Connection and Functional Diagrams Dual-In-Line, Small Outline and SSOP Packages 00550101 Molded Chip Carrier Package 00550133 Top View © 2004 National Semiconductor Corporation DS005501 www.national.com ADC0820 8-Bit High Speed µP Compatible A/D Converter with Track/Hold Function March 2004 ADC0820 Connection and Functional Diagrams (Continued) 00550102 FIGURE 1. Ordering Information Part Number Total Package Unadjusted Error ADC0820BCV ADC0820BCWM Range V20A — Molded Chip Carrier ± 1⁄2 LSB Temperature 0˚C to +70˚C M20B — Wide Body Small Outline 0˚C to +70˚C ADC0820BCN N20A — Molded DIP 0˚C to +70˚C ADC0820CCJ J20A — Cerdip −40˚C to +85˚C M20B — Wide Body Small Outline 0˚C to +70˚C M20B — Wide Body Small Outline −40˚C to +85˚C N20A — Molded DIP 0˚C to +70˚C ADC0820CCWM ADC0820CIWM ADC0820CCN www.national.com ± 1 LSB 2 Dual-In-Line Package (ceramic) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Surface Mount Package Supply Voltage (VCC) 300˚C Vapor Phase (60 sec.) 215˚C Infrared (15 sec.) 220˚C 10V Logic Control Inputs −0.2V to VCC +0.2V Voltage at Other Inputs and Output −0.2V to VCC +0.2V Storage Temperature Range Operating Ratings TMIN≤TA≤TMAX Temperature Range −65˚C to +150˚C Package Dissipation at TA = 25˚C (Notes 1, 2) 875 mW ADC0820CCJ −40˚C≤TA≤+85˚C ADC0820CIWM −40˚C≤TA≤+85˚C Input Current at Any Pin (Note 5) 1 mA Package Input Current (Note 5) 4 mA ADC0820BCN, ADC0820CCN 900V ADC0820BCV 0˚C≤TA≤70˚C ADC0820BCWM, ADC0820CCWM 0˚C≤TA≤70˚C ESD Susceptability (Note 9) Lead Temp. (Soldering, 10 sec.) Dual-In-Line Package (plastic) 0˚C≤TA≤70˚C VCC Range 260˚C 4.5V to 8V Converter Characteristics The following specifications apply for RD mode (pin 7=0), VCC=5V, VREF(+)=5V,and VREF(−)=GND unless otherwise specified. Boldface limits apply from TMIN to TMAX; all other limits TA=Tj=25˚C. Parameter Conditions ADC0820BCN, ADC0820CCN ADC0820CCJ ADC0820BCV, ADC0820BCWM Limit Units ADC0820CCWM, ADC0820CIWM Typ Tested Design Typ Limit Limit (Note 6) (Note 7) (Note 8) (Note 6) Resolution 8 Total Unadjusted ADC0820BCN, BCWM Error ADC0820CCJ (Note 3) ADC0820CCN, CCWM, CIWM Design Limit Limit (Note 7) (Note 8) 8 8 Bits ± 1⁄2 ± 1⁄2 LSB ±1 ±1 ±1 ±1 LSB ±1 LSB ADC0820CCMSA Minimum Reference Tested LSB 2.3 1.00 2.3 1.2 kΩ 2.3 6 2.3 5.3 6 kΩ VCC VCC VCC V GND GND GND V VREF(−) VREF(−) VREF(−) V VREF(+) VREF(+) VREF(+) V VCC+0.1 VCC+0.1 VCC+0.1 V GND−0.1 GND−0.1 GND−0.1 V Resistance Maximum Reference Resistance Maximum VREF(+) Input Voltage Minimum VREF(−) Input Voltage Minimum VREF(+) Input Voltage Maximum VREF(−) Input Voltage Maximum VIN Input Voltage Minimum VIN Input Voltage Maximum Analog CS =VCC Input Leakage VIN=VCC 3 0.3 3 µA Current VIN=GND −3 −0.3 −3 µA Power Supply Sensitivity VCC=5V ± 5% ± 1⁄4 ± 1⁄4 LSB ± 1/16 ± 1⁄4 3 ± 1/16 www.national.com ADC0820 Absolute Maximum Ratings (Notes 1, 2) ADC0820 DC Electrical Characteristics The following specifications apply for VCC=5V, unless otherwise specified. Boldface limits apply from TMIN to TMAX; all other limits TA=TJ=25˚C. Parameter Conditions ADC0820BCN, ADC0820CCN ADC0820CCJ Limit Units ADC0820BCV, ADC0820BCWM ADC0820CCWM, ADC0820CIWM Typ Tested Design Typ Limit Limit (Note 6) (Note 7) (Note 8) (Note 6) VIN(1), Logical “1” VCC=5.25V Input Voltage VIN(0), Logical “0” VCC=4.75V Input Voltage Tested Design Limit Limit (Note 7) (Note 8) CS , WR , RD 2.0 2.0 2.0 V Mode 3.5 3.5 3.5 V CS , WR , RD 0.8 0.8 0.8 V Mode 1.5 1.5 1.5 V 1 µA µA IIN(1), Logical “1” VIN(1)=5V; CS , RD Input Current VIN(1)=5V; WR VIN(1)=5V; Mode 0.005 IIN(0), Logical “0” VIN(0)=0V; CS , RD , WR , Input Current Mode VOUT(1), Logical “1” VCC=4.75V, IOUT=−360 µA; Output Voltage DB0–DB7, OFL , INT 1 0.005 0.1 3 0.1 0.3 3 50 200 50 170 200 µA −0.005 −1 −0.005 −1 µA VCC=4.75V, IOUT=−10 µA; 2.4 2.8 2.4 V 4.5 4.6 4.5 V 0.4 0.34 0.4 V DB0–DB7, OFL , INT VOUT(0), Logical “0” VCC=4.75V, IOUT=1.6 mA; Output Voltage DB0–DB7, OFL , INT , RDY IOUT, TRI-STATE VOUT=5V; DB0–DB7, RDY 0.1 3 0.1 0.3 3 µA Output Current VOUT=0V; DB0–DB7, RDY −0.1 −3 −0.1 −0.3 −3 µA ISOURCE, Output VOUT=0V; DB0–DB7, OFL −12 −6 −12 −7.2 −6 mA Source Current INT −9 −4.0 −9 −5.3 −4.0 mA ISINK, Output Sink VOUT=5V; DB0–DB7, OFL , 14 7 14 8.4 7 mA 7.5 15 7.5 13 15 mA Current INT , RDY ICC, Supply Current CS =WR =RD =0 AC Electrical Characteristics The following specifications apply for VCC=5V, tr=tf=20 ns, VREF(+)=5V, VREF(−)=0V and TA=25˚C unless otherwise specified. Typ Parameter Conditions (Note 6) Tested Design Limit Limit (Note 7) (Note 8) Units tCRD, Conversion Time for RD Mode Pin 7 = 0, Figure 2 1.6 2.5 µs tACC0, Access Time (Delay from Pin 7 = 0, Figure 2 tCRD+20 tCRD+50 ns 1.52 µs Falling Edge of RD to Output Valid) tCWR-RD, Conversion Time for Pin 7 = VCC; tWR = 600 ns, WR-RD Mode tRD=600 ns; Figures 3, 4 tWR, Write Time tRD, Read Time Min Pin 7 = VCC; Figures 3, 4 Max (Note 4) See Graph Min Pin 7 = VCC; Figures 3, 4 600 ns 50 µs 600 ns (Note 4) See Graph tACC1, Access Time (Delay from Pin 7 = VCC, tRD < tI; Figure 3 Falling Edge of RD to Output Valid) CL=15 pF 190 280 ns CL=100 pF 210 320 ns www.national.com 4 (Continued) The following specifications apply for VCC=5V, tr=tf=20 ns, VREF(+)=5V, VREF(−)=0V and TA=25˚C unless otherwise specified. Parameter tACC2, Access Time (Delay from Falling Edge of RD to Output Valid) Conditions Typ Tested (Note 6) Limit Design Limit (Note 7) (Note 8) Units Pin 7 = VCC, tRD > tI; Figure 4 CL=15 pF 70 120 ns CL=100 pF 90 150 ns tACC3, Access Time (Delay from Rising Edge of RDY to Output Valid) RPULLUP = 1k and CL = 15 pF 30 tI, Internal Comparison Time Pin 7=VCC; Figures 4, 5 800 1300 ns 100 200 ns tI ns ns CL=50 pF t1H, t0H, TRI-STATE Control RL=1k, CL=10 pF (Delay from Rising Edge of RD to Hi-Z State) tINTL, Delay from Rising Edge of Pin 7 = VCC, CL= 50 pF WR to Falling Edge of INT tRD > tI; Figure 4 tRD < tI; Figure 3 tRD+200 tRD+290 ns tINTH, Delay from Rising Edge of Figures 2, 3, 4 125 225 ns RD to Rising Edge of INT CL=50 pFc tINTHWR, Delay from Rising Edge of Figure 5, CL=50 pF 175 270 ns tRDY, Delay from CS to RDY Figure 2, CL=50 pF, Pin 7 =0 50 100 ns tID, Delay from INT to Output Valid Figure 5 20 50 ns Pin 7=VCC, tRD < tI 200 290 ns 500 ns WR to Rising Edge of INT tRI, Delay from RD to INT Figure 3 tP, Delay from End of Conversion Figures 2, 3, 4, 5 to Next Conversion (Note 4) See Graph Slew Rate, Tracking 0.1 CVIN, Analog Input Capacitance 45 V/µs pF COUT, Logic Output Capacitance 5 pF CIN, Logic Input Capacitance 5 pF Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its specified operating conditions. Note 2: All voltages are measured with respect to the GND pin, unless otherwise specified. Note 3: Total unadjusted error includes offset, full-scale, and linearity errors. Note 4: Accuracy may degrade if tWR or tRD is shorter than the minimum value specified. See Accuracy vs. tWR and Accuracy vs. tRD graphs. Note 5: When the input voltage (VIN) at any pin exceeds the power supply rails (VIN < V−or VIN > V+) the absolute value of current at that pin should be limited to 1 mA or less. The 4 mA package input current limits the number of pins that can exceed the power supply boundaries with a 1 mA current limit to four. Note 6: Typicals are at 25˚C and represent most likely parametric norm. Note 7: Tested limits are guaranteed to National’s AOQL (Average Outgoing Quality Level). Note 8: Design limits are guaranteed but not 100% tested. These limits are not used to calculate outgoing quality levels. Note 9: Human body model, 100 pF discharged through a 1.5 kΩ resistor. 5 www.national.com ADC0820 AC Electrical Characteristics ADC0820 TRI-STATE Test Circuits and Waveforms t1H 00550103 00550104 tr=20 ns t0H 00550106 tr=20 ns 00550105 Timing Diagrams 00550107 Note: On power-up the state of INT can be high or low. FIGURE 2. RD Mode (Pin 7 is Low) www.national.com 6 ADC0820 Timing Diagrams (Continued) 00550108 FIGURE 3. WR-RD Mode (Pin 7 is High and tRD < tI) 00550109 FIGURE 4. WR-RD Mode (Pin 7 is High and tRD > tI) 00550110 FIGURE 5. WR-RD Mode (Pin 7 is High) Stand-Alone Operation 7 www.national.com ADC0820 Typical Performance Characteristics Logic Input Threshold Voltage vs. Supply Voltage Conversion Time (RD Mode) vs. Temperature 00550134 00550135 Power Supply Current vs. Temperature (not including reference ladder) Accuracy vs. tWR 00550137 00550136 Accuracy vs. tRD Accuracy vs. tp 00550139 00550138 www.national.com 8 (Continued) Accuracy vs. VREF [VREF=VREF(+)-VREF(-)] tI, Internal Time Delay vs. Temperature 00550140 00550141 Output Current vs. Temperature 00550142 9 www.national.com ADC0820 Typical Performance Characteristics ADC0820 Description of Pin Functions Pin Name Pin Name Function 1 VIN Analog input; range =GND≤VIN≤VCC 2 DB0 TRI-STATE data output — bit 0 (LSB) 3 DB1 TRI-STATE data output — bit 1 4 DB2 TRI-STATE data output — bit 2 5 DB3 TRI-STATE data output — bit 3 6 WR /RDY WR-RD Mode 9 INT WR: With CS low, the conversion is started on the falling edge of WR. Approximately 800 ns (the preset internal time out, tI) after the WR rising edge, the result of the conversion will be strobed into the output latch, provided that RD does not occur prior to this time out (see Figures 3, 4 ). RD Mode INT going low indicates that the conversion is completed and the data result is in the output latch. INT is reset by the rising edge of RD or CS (see Figure 2 ). RDY: This is an open drain output (no internal pull-up device). RDY will go low after the falling edge of CS; RDY will go TRI-STATE when the result of the conversion is strobed into the output latch. It is used to simplify the interface to a microprocessor system (see Figure 2 ). 8 Mode RD 10 GND Ground 11 VREF(−) The bottom of resistor ladder, voltage range: GND≤VREF(−)≤VREF(+) (Note 5) 12 VREF(+) The top of resistor ladder, voltage range: VREF(−)≤VREF(+)≤VCC (Note 5) 13 CS Mode: Mode selection input — it is internally tied to GND through a 50 µA current source. CS must be low in order for the RD or WR to be recognized by the converter. 14 DB4 TRI-STATE data output — bit 4 15 DB5 TRI-STATE data output — bit 5 RD Mode: When mode is low 16 DB6 TRI-STATE data output — bit 6 WR-RD Mode: When mode is high 17 DB7 TRI-STATE data output — bit 7 (MSB) WR-RD Mode 18 OFL Overflow output — If the analog input is higher than the VREF(+), OFL will be low at the end of conversion. It can be used to cascade 2 or more devices to have more resolution (9, 10-bit). This output is always active and does not go into TRI-STATE as DB0–DB7 do. 19 NC No connection 20 VCC Power supply voltage With CS low, the TRI-STATE data outputs (DB0-DB7) will be activated when RD goes low (see Figure 5 ). RD can also be used to increase the speed of the converter by reading data prior to the preset internal time out (tI, ∼800 ns). If this is done, the data result transferred to output latch is latched after the falling edge of the RD (see Figures 3, 4 ). RD Mode 1.0 Functional Description With CS low, the conversion will start with RD going low, also RD will enable the TRI-STATE data outputs at the completion of the conversion. RDY going TRI-STATE and INT going low indicates the completion of the conversion (see Figure 2 ). www.national.com WR-RD Mode INT going low indicates that the conversion is completed and the data result is in the output latch. INT will go low, ∼800 ns (the preset internal time out, tI) after the rising edge of WR (see Figure 4 ); or INT will go low after the falling edge of RD , if RD goes low prior to the 800 ns time out (see Figure 3). INT is reset by the rising edge of RD or CS (see Figures 3, 4 ). RD Mode 7 Function 1.1 GENERAL OPERATION The ADC0820 uses two 4-bit flash A/D converters to make an 8-bit measurement (Figure 1 ). Each flash ADC is made up of 15 comparators which compare the unknown input to a reference ladder to get a 4-bit result. To take a full 8-bit reading, one flash conversion is done to provide the 4 most significant data bits (via the MS flash ADC). Driven by the 4 MSBs, an internal DAC recreates an analog approximation of the input voltage. This analog signal is then subtracted from the input, and the difference voltage is converted by a second 4-bit flash ADC (the LS ADC), providing the 4 least significant bits of the output data word. The internal DAC is actually a subsection of the MS flash converter. This is accomplished by using the same resistor ladder for the A/D as well as for generating the DAC signal. The DAC output is actually the tap on the resistor ladder 10 ADC0820 1.0 Functional Description (Continued) which most closely approximates the analog input. In addition, the “sampled-data” comparators used in the ADC0820 provide the ability to compare the magnitudes of several analog signals simultaneously, without using input summing amplifiers. This is especially useful in the LS flash ADC, where the signal to be converted is an analog difference. 1.2 THE SAMPLED-DATA COMPARATOR Each comparator in the ADC0820 consists of a CMOS inverter with a capacitively coupled input (Figures 6, 7 ). Analog switches connect the two comparator inputs to the input capacitor (C) and also connect the inverter’s input and output. This device in effect now has one differential input pair. A comparison requires two cycles, one for zeroing the comparator, and another for making the comparison. In the first cycle, one input switch and the inverter’s feedback switch (Figure 6 ) are closed. In this interval, C is charged to the connected input (V1) less the inverter’s bias voltage (VB, approximately 1.2V). In the second cycle (Figure 7 ), these two switches are opened and the other (V2) input’s switch is closed. The input capacitor now subtracts its stored voltage from the second input and the difference is amplified by the inverter’s open loop gain. The inverter’s input (VB') becomes 00550112 • VO = VB • V on C = V1−VB • CS = stray input node capacitor • VB = inverter input bias voltage Zeroing Phase FIGURE 6. Sampled-Data Comparator 00550113 and the output will go high or low depending on the sign of VB'−VB. The actual circuitry used in the ADC0820 is a simple but important expansion of the basic comparator described above. By adding a second capacitor and another set of switches to the input (Figure 8 ), the scheme can be expanded to make dual differential comparisons. In this circuit, the feedback switch and one input switch on each capacitor (Z switches) are closed in the zeroing cycle. A comparison is then made by connecting the second input on each capacitor and opening all of the other switches (S switches). The change in voltage at the inverter’s input, as a result of the change in charge on each input capacitor, will now depend on both input signal differences. Compare Phase FIGURE 7. Sampled-Data Comparator 00550145 00550114 FIGURE 8. ADC0820 Comparator (from MS Flash ADC) 1.3 ARCHITECTURE In the ADC0820, one bank of 15 comparators is used in each 4-bit flash A/D converter (Figure 12 ). The MS (most significant) flash ADC also has one additional comparator to detect input overrange. These two sets of comparators operate alternately, with one group in its zeroing cycle while the other is comparing. When a typical conversion is started, the WR line is brought low. At this instant the MS comparators go from zeroing to 11 www.national.com ADC0820 1.0 Functional Description data which relate to interface timing. If an interrupt driven scheme is desired, the user can wait for INT to go low before reading the conversion result (Figure 10 ). INT will typically go low 800 ns after WR’s rising edge. However, if a shorter conversion time is desired, the processor need not wait for INT and can exercise a read after only 600 ns (Figure 9 ). If this is done, INT will immediately go low and data will appear at the outputs. (Continued) comparison mode (Figure 11 ). When WR is returned high after at least 600 ns, the output from the first set of comparators (the first flash) is decoded and latched. At this point the two 4-bit converters change modes and the LS (least significant) flash ADC enters its compare cycle. No less than 600 ns later, the RD line may be pulled low to latch the lower 4 data bits and finish the 8-bit conversion. When RD goes low, the flash A/Ds change state once again in preparation for the next conversion. Figure 11 also outlines how the converter’s interface timing relates to its analog input (VIN). In WR-RD mode, VIN is measured while WR is low. In RD mode, sampling occurs during the first 800 ns of RD. Because of the input connections to the ADC0820’s LS and MS comparators, the converter has the ability to sample VIN at one instant (Section 2.4), despite the fact that two separate 4-bit conversions are being done. More specifically, when WR is low the MS flash is in compare mode (connected to VIN), and the LS flash is in zero mode (also connected to VIN). Therefore both flash ADCs sample VIN at the same time. 00550117 1.4 DIGITAL INTERFACE The ADC0820 has two basic interface modes which are selected by strapping the MODE pin high or low. FIGURE 9. WR-RD Mode (Pin 7 is High and tRD < tI) RD Mode With the MODE pin grounded, the converter is set to Read mode. In this configuration, a complete conversion is done by pulling RD low until output data appears. An INT line is provided which goes low at the end of the conversion as well as a RDY output which can be used to signal a processor that the converter is busy or can also serve as a system Transfer Acknowledge signal. RD Mode (Pin 7 is Low) 00550118 FIGURE 10. WR-RD Mode (Pin 7 is High and tRD > tI) Stand-Alone For stand-alone operation in WR-RD mode, CS and RD can be tied low and a conversion can be started with WR. Data will be valid approximately 800 ns following WR’s rising edge. WR-RD Mode (Pin 7 is High) Stand-Alone Operation 00550116 When in RD mode, the comparator phases are internally triggered. At the falling edge of RD, the MS flash converter goes from zero to compare mode and the LS ADC’s comparators enter their zero cycle. After 800 ns, data from the MS flash is latched and the LS flash ADC enters compare mode. Following another 800 ns, the lower 4 bits are recovered. WR then RD Mode With the MODE pin tied high, the A/D will be set up for the WR-RD mode. Here, a conversion is started with the WR input; however, there are two options for reading the output www.national.com 00550119 12 ADC0820 1.0 Functional Description (Continued) 00550120 Note: MS means most significant LS means least significant FIGURE 11. Operating Sequence (WR-RD Mode) Since the MS flash ADC enters its zeroing phase at the end of a conversion (Section 1.3), a new conversion cannot be started until this phase is complete. The minimum spec for this time (tP, Figures 2, 3, 4, 5 ) is 500 ns. OTHER INTERFACE CONSIDERATIONS In order to maintain conversion accuracy, WR has a maximum width spec of 50 µs. When the MS flash ADC’s sampled-data comparators (Section 1.2) are in comparison mode (WR is low), the input capacitors (C, Figure 8 ) must hold their charge. Switch leakage and inverter bias current can cause errors if the comparator is left in this phase for too long. 13 www.national.com ADC0820 Detailed Block Diagram 00550115 FIGURE 12. www.national.com 14 2.1 REFERENCE AND INPUT The two VREF inputs of the ADC0820 are fully differential and define the zero to full-scale input range of the A to D converter. This allows the designer to easily vary the span of the analog input since this range will be equivalent to the voltage difference between VIN(+) and VIN(−). By reducing VREF(VREF=VREF(+)−VREF(−)) to less than 5V, the sensitivity of the converter can be increased (i.e., if VREF=2V then 1 LSB=7.8 mV). The input/reference arrangement also facilitates ratiometric operation and in many cases the chip power supply can be used for transducer power as well as the VREF source. The input capacitors must charge to the input voltage through the on resistance of the analog switches (about 5 kΩ to 10 kΩ). In addition, about 12 pF of input stray capacitance must also be charged. For large source resistances, the analog input can be modeled as an RC network as shown in Figure 15. As RS increases, it will take longer for the input capacitance to charge. This reference flexibility lets the input span not only be varied but also offset from zero. The voltage at VREF(−) sets the input level which produces a digital output of all zeroes. Though VIN is not itself differential, the reference design affords nearly differential-input capability for most measurement applications. Figure 13 shows some of the configurations that are possible. In RD mode, the input switches are closed for approximately 800 ns at the start of the conversion. In WR-RD mode, the time that the switches are closed to allow this charging is the time that WR is low. Since other factors force this time to be at least 600 ns, input time constants of 100 ns can be accommodated without special consideration. Typical total input capacitance values of 45 pF allow RS to be 1.5 kΩ without lengthening WR to give VIN more time to settle. 2.2 INPUT CURRENT Due to the unique conversion techniques employed by the ADC0820, the analog input behaves somewhat differently than in conventional devices. The A/D’s sampled-data comparators take varying amounts of input current depending on which cycle the conversion is in. External Reference 2.5V Full-Scale Power Supply as Reference Input Not Referred to GND 00550122 00550121 00550123 FIGURE 13. Analog Input Options 15 www.national.com ADC0820 The equivalent input circuit of the ADC0820 is shown in Figure 14. When a conversion starts (WR low, WR-RD mode), all input switches close, connecting VIN to thirty-one 1 pF capacitors. Although the two 4-bit flash circuits are not both in their compare cycle at the same time, VIN still sees all input capacitors at once. This is because the MS flash converter is connected to the input during its compare interval and the LS flash is connected to the input during its zeroing phase (Section 1.3). In other words, the LS ADC uses VIN as its zero-phase input. 2.0 Analog Considerations ADC0820 2.0 Analog Considerations occur. The comparators’ outputs are not latched while WR is low, so at least 600 ns will be provided to charge the ADC’s input capacitance. It is therefore not necessary to filter out these transients by putting an external cap on the VIN terminal. (Continued) 2.4 INHERENT SAMPLE-HOLD Another benefit of the ADC0820’s input mechanism is its ability to measure a variety of high speed signals without the help of an external sample-and-hold. In a conventional SAR type converter, regardless of its speed, the input must remain at least 1⁄2 LSB stable throughout the conversion process if full accuracy is to be maintained. Consequently, for many high speed signals, this signal must be externally sampled, and held stationary during the conversion. Sampled-data comparators, by nature of their input switching, already accomplish this function to a large degree (Section 1.2). Although the conversion time for the ADC0820 is 1.5 µs, the time through which VIN must be 1⁄2 LSB stable is much smaller. Since the MS flash ADC uses VIN as its “compare” input and the LS ADC uses VIN as its “zero” input, the ADC0820 only “samples” VIN when WR is low (Sections 1.3 and 2.2). Even though the two flashes are not done simultaneously, the analog signal is measured at one instant. The value of VIN approximately 100 ns after the rising edge of WR (100 ns due to internal logic prop delay) will be the measured value. Input signals with slew rates typically below 100 mV/µs can be converted without error. However, because of the input time constants, and charge injection through the opened comparator input switches, faster signals may cause errors. Still, the ADC0820’s loss in accuracy for a given increase in signal slope is far less than what would be witnessed in a conventional successive approximation device. An SAR type converter with a conversion time as fast as 1 µs would still not be able to measure a 5V 1 kHz sine wave without the aid of an external sample-and-hold. The ADC0820, with no such help, can typically measure 5V, 7 kHz waveforms. 00550124 FIGURE 14. 00550125 FIGURE 15. 2.3 INPUT FILTERING It should be made clear that transients in the analog input signal, caused by charging current flowing into VIN, will not degrade the A/D’s performance in most cases. In effect the ADC0820 does not “look” at the input when these transients www.national.com 16 ADC0820 3.0 Typical Applications 8-Bit Resolution Configuration 00550126 9-Bit Resolution Configuration 00550127 17 www.national.com ADC0820 3.0 Typical Applications (Continued) Multiple Input Channels Telecom A/D Converter 00550129 00550128 • VIN=3 kHz max ± 4VP • No track-and-hold needed • Low power consumption 8-Bit 2-Quadrant Analog Multiplier 00550130 www.national.com 18 ADC0820 3.0 Typical Applications (Continued) Fast Infinite Sample-and-Hold 00550131 19 www.national.com www.national.com 20 3.0 Typical Applications (Continued) Digital Waveform Recorde 00550132 ADC0820 ADC0820 Physical Dimensions inches (millimeters) unless otherwise noted Hermetic Dual-In-Line Package (J) Order Number ADC0820CCJ NS Package Number J20A SO Package (M) Order Number ADC0820BCWM, ADC0820CCWM or ADC0820CIWM NS Package Number M20B 21 www.national.com ADC0820 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Molded Dual-In-Line Package (N) Order Number ADC0820BCN or ADC0820CCN NS Package Number N20A Molded Chip Carrier Package (V) Order Number ADC0820BCV NS Package Number V20A www.national.com 22 LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. ADC0820 8-Bit High Speed µP Compatible A/D Converter with Track/Hold Function Notes IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated