AMD AM29LV641GH53REI

Am29LV641G
Data Sheet
RETIRED
PRODUCT
This product has been retired and is not recommended for designs. For new and current designs,
S29GL064A supersedes Am29LV641G and is the factory-recommended migration path. Please refer
to the S29GL064A datasheet for specifications and ordering information. Availability of this document is retained for reference and historical purposes only.
June 2005
The following document specifies Spansion memory products that are now offered by both Advanced
Micro Devices and Fujitsu. Although the document is marked with the name of the company that
originally developed the specification, these products will be offered to customers of both AMD and
Fujitsu.
Continuity of Specifications
There is no change to this datasheet as a result of offering the device as a Spansion product. Any
changes that have been made are the result of normal datasheet improvement and are noted in the
document revision summary, where supported. Future routine revisions will occur when appropriate, and changes will be noted in a revision summary.
For More Information
Please contact your local AMD or Fujitsu sales office for additional information about Spansion
memory solutions.
Publication Number 25295
Revision A
Amendment +3
Issue Date June 14, 2005
THIS PAGE LEFT INTENTIONALLY BLANK.
ADVANCE INFORMATION
Am29LV641G
64 Megabit (4 M x 16-Bit) CMOS 3.0 Volt-only
Uniform Sector Flash Memory with VersatileI/O™ Control
This product has been retired and is not recommended for designs. For new and current designs, S29GL064A supersedes Am29LV641G and is the factory-recommended migration path.
Please refer to the S29GL064A datasheet for specifications and ordering information. Availability of this document is retained for reference and historical purposes only.
DISTINCTIVE CHARACTERISTICS
ARCHITECTURAL ADVANTAGES
■ Single power supply operation
— 2.7 to 3.6 volt read, erase, and program operations
■ SecSi™ (Secured Silicon) Sector region
— 128-word sector for permanent, secure identification
through an 8-word random Electronic Serial Number
— May be programmed and locked at the factory or by
the customer
— Accessible through a command sequence
■ VersatileI/O™ control
— Device generates data output voltages and tolerates
data input voltages as determined by the voltage on
the VIO pin
■ Manufactured on 0.18 µm process technology
■ Flexible sector architecture
— One hundred twenty-eight 32 Kword sectors
■ Compatibility with JEDEC standards
— Pinout and software compatible with single-power
supply Flash standard
■ Package options
— 48-pin TSOP and Reverse TSOP (LV641GH/L only)
— 63-ball Fine-Pitch BGA (LV640GU only)
— 64-ball Fortified BGA (LV640GU only)
■ Minimum 1 million erase cycle guarantee per sector
■ 20-year data retention at 125°C
PERFORMANCE CHARCTERISTICS
■ High performance
— Access time ratings as fast as 55 ns
■ Ultra low power consumption (typical values at 3.0 V,
5 MHz)
— 9 mA typical active read current
— 26 mA typical erase/program current
— 200 nA typical standby mode current
■ Program and erase performance (VHH not applied to
the ACC input pin)
— Word program time: 7 µs typical
— Sector erase time: 0.6 s typical for each 32 Kword
sector
SOFTWARE AND HARDWARE FEATURES
■ Hardware features
— Hardware reset input (RESET#): resets device for
new operation
— WP# input: protects first or last 32 Kword sector
regardless of sector protection settings
(LV641GH/L only)
— ACC input: Accelerates programming time for higher
throughput during system production
■ Software features
— Program Suspend & Resume: read other sectors
before programming operation is completed
— Sector Group Protection: VCC-level method of
preventing program or erase operations within a
sector
— Temporary Sector Group Unprotect: VID-level method
of changing in previously locked sectors
— CFI (Common Flash Interface) compliant: allows host
system to identify and accommodate multiple flash
devices
— Erase Suspend/Erase Resume: read/program other
sectors before an erase operation is complete
— Data# Polling and toggle bits provide erase and
programming operation status
— Unlock Bypass Program command reduces overall
multiple-word programming time
This document contains information on a product under development at Advance Micro Devices. The information is
intended to help you evaluate this product. Do not design in the product without contacting the factory. AMD reserves
the right to change or discontinue work on this proposed product without notice.
Publication# 25295 Rev: A Amendment/+3
Issue Date: June 14, 2005
Refer to AMD’s Website (www.amd.com) for the latest information.
A D V A N C E
I N F O R M A T I O N
GENERAL DESCRIPTION
The Am29LV641G are 64 Mbit, 3.0 volt (3.0 V to 3.6 V)
single power supply flash memory devices organized
as 4,194,304 words. Data appears on DQ15–DQ0.
These devices are designed to be programmed in-system with the standard system 3.0 volt VCC supply. A
12.0 volt VPP is not required for program or erase operations. The device can also be programmed in standard EPROM programmers.
Access times of 55 regulated volage and 70 ns full
voltage range are available for applications where VIO
≥ V CC . The Am29LV641GH/L is offered in 48-pin
T S O P a n d r eve r s e T S O P p a ck a g e s. T h e
Am29LV640GU is offered in a 63-ball Fine-pitch BGA
package, and a 64-ball Fortified BGA. To eliminate bus
contention each device has separate chip enable
(CE#), write enable (WE#) and output enable (OE#)
controls.
Each device requires only a single 3.0 volt power
supply (2.7 V to 3.6 V) for both read and write functions. Internally generated and regulated voltages are
provided for the program and erase operations.
The device is entirely command set compatible with
the JEDEC single-power-supply Flash standard.
Commands are written to the command register using
standard microprocessor write timing. Register contents serve as inputs to an internal state-machine that
controls the erase and programming circuitry. Write
cycles also internally latch addresses and data
needed for the programming and erase operations.
Reading data out of the device is similar to reading
from other Flash or EPROM devices.
Device programming occurs by executing the program
command sequence. This initiates the Embedded
Program algorithm—an internal algorithm that automatically times the program pulse widths and verifies
proper cell margin. The Unlock Bypass mode facilitates faster programming times by requiring only two
write cycles to program data instead of four.
Device erasure occurs by executing the erase command sequence. This initiates the Embedded Erase
algorithm—an internal algorithm that automatically
preprograms the array (if it is not already programmed) before executing the erase operation. During erase, the device automatically times the erase
pulse widths and verifies proper cell margin.
The VersatileI/O™ (VIO) control allows the host system to set the voltage levels that the device generates
at its data outputs and the voltages tolerated at its
data inputs to the same voltage level that is asserted
on the VIO pin. This allows the device to operate in 1.8
V or 3 V system environment as required.
The host system can detect whether a program or
erase operation is complete by reading the DQ7
(Data# Polling) or DQ6 (toggle) status bits. After a
program or erase cycle has been completed, the de5
vice is ready to read array data or accept another
command.
The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting
the data contents of other sectors. The device is fully
erased when shipped from the factory.
Hardware data protection measures include a low
V CC detector that automatically inhibits write operations during power transitions. The hardware sector
protection feature disables both program and erase
operations in any combination of sectors of memory.
This can be achieved in-system or via programming
equipment.
The Erase Suspend/Erase Resume feature enables
the user to put erase on hold for any period of time to
read data from, or program data to, any sector that is
not selected for erasure. True background erase can
thus be achieved. The Program Suspend/Program
Resume feature enables the host system to pause a
program operation in a given sector to read any other
sector and then complete the program operation.
The hardware RESET# pin terminates any operation
in progress and resets the internal state machine to
reading array data. The RESET# pin may be tied to
the system reset circuitry. A system reset would thus
also reset the device, enabling the system microprocessor to read boot-up firmware from the Flash memory device.
The device offers a standby mode as a power-saving
feature. Once the system places the device into the
standby mode power consumption is greatly reduced.
The SecSi™ (Secured Silicon) Sector provides an
minimum 128-word area for code or data that can be
permanently protected. Once this sector is protected,
no further programming or erasing within the sector
can occur.
The Write Protect (WP#) feature protects the first or
last sector by asserting a logic low on the WP# pin.
The protected sector will still be protected even during
accelerated programming. (Am29LV641GH/L only)
The accelerated program (ACC) feature allows the
system to program the device at a much faster rate.
When ACC is pulled high to VHH, the device enters the
Unlock Bypass mode, enabling the user to reduce the
time needed to do the program operation. This feature
is intended to increase factory throughput during system production, but may also be used in the field if desired.
AMD’s Flash technology combines years of Flash
memory manufacturing experience to produce the
highest levels of quality, reliability and cost effectiveness. The device electrically erases all bits within a
sector simultaneously via Fowler-Nordheim tunnelling.
The data is programmed using hot electron injection.
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
TABLE OF CONTENTS
Product Selector Guide . . . . . . . . . . . . . . . . . . . . . 4
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . 5
Special Package Handling Instructions .................................... 7
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . 9
Device Bus Operations . . . . . . . . . . . . . . . . . . . . . 10
DQ7: Data# Polling ................................................................. 30
Figure 6. Data# Polling Algorithm .................................................. 30
DQ6: Toggle Bit I .................................................................... 30
Figure 7. Toggle Bit Algorithm........................................................ 31
DQ2: Toggle Bit II ................................................................... 32
Reading Toggle Bits DQ6/DQ2 ............................................... 32
DQ5: Exceeded Timing Limits ................................................ 32
DQ3: Sector Erase Timer ....................................................... 32
Table 1. Device Bus Operations .....................................................10
Table 11. Write Operation Status ................................................... 33
VersatileI/O™ (VIO) Control .................................................... 10
Requirements for Reading Array Data ................................... 10
Writing Commands/Command Sequences ............................ 11
Absolute Maximum Ratings . . . . . . . . . . . . . . . . 34
Figure 8. Maximum Negative Overshoot Waveform ..................... 34
Figure 9. Maximum Positive Overshoot Waveform....................... 34
Accelerated Program Operation ......................................................11
Autoselect Functions .......................................................................11
Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . 34
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 35
Standby Mode ........................................................................ 11
Automatic Sleep Mode ........................................................... 11
RESET#: Hardware Reset Pin ............................................... 11
Output Disable Mode .............................................................. 12
Figure 10. ICC1 Current vs. Time (Showing
Active and Automatic Sleep Currents) ........................................... 36
Figure 11. Typical ICC1 vs. Frequency ............................................ 36
Table 2. Sector Address Table ........................................................12
Autoselect Mode ..................................................................... 16
Table 3. Autoselect Codes, (High Voltage Method) ......................16
Sector Group Protection and Unprotection ............................. 17
Table 4. Sector Group Protection/Unprotection Address Table .....17
Write Protect (WP#) ................................................................ 18
Temporary Sector Group Unprotect ....................................... 18
Figure 1. Temporary Sector Group Unprotect Operation................ 18
Figure 2. In-System Sector Group Protect/Unprotect Algorithms ... 19
SecSi™ (Secured Silicon) Sector Flash Memory Region ....... 20
Table 5. SecSi Sector Contents ......................................................20
Figure 3. SecSi Sector Protect Verify.............................................. 21
Hardware Data Protection ...................................................... 21
Low VCC Write Inhibit .......................................................................21
Write Pulse “Glitch” Protection ........................................................21
Logical Inhibit ..................................................................................21
Power-Up Write Inhibit ....................................................................21
Common Flash Memory Interface (CFI) . . . . . . . 21
Table 6. CFI Query Identification String .......................................... 22
Table 7. System Interface String..................................................... 22
Table 8. Device Geometry Definition .............................................. 22
Table 9. Primary Vendor-Specific Extended Query ........................ 24
Command Definitions . . . . . . . . . . . . . . . . . . . . . 24
Reading Array Data ................................................................ 24
Reset Command ..................................................................... 25
Autoselect Command Sequence ............................................ 25
Enter SecSi Sector/Exit SecSi Sector Command Sequence .. 25
Word Program Command Sequence ..................................... 25
Unlock Bypass Command Sequence ..............................................26
Figure 4. Program Operation .......................................................... 26
Chip Erase Command Sequence ........................................... 26
Sector Erase Command Sequence ........................................ 27
Erase Suspend/Erase Resume Commands ........................... 27
Figure 5. Erase Operation............................................................... 28
Command Definitions ............................................................. 29
Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 12. Test Setup.................................................................... 37
Table 12. Test Specifications ......................................................... 37
Key to Switching Waveforms. . . . . . . . . . . . . . . . 37
Figure 13. Input Waveforms and
Measurement Levels...................................................................... 37
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 38
Read-Only Operations ........................................................... 38
Figure 14. Read Operation Timings ............................................... 38
Hardware Reset (RESET#) .................................................... 39
Figure 15. Reset Timings ............................................................... 39
Erase and Program Operations .............................................. 40
Figure 16. Program Operation Timings..........................................
Figure 17. Accelerated Program Timing Diagram..........................
Figure 18. Chip/Sector Erase Operation Timings ..........................
Figure 19. Data# Polling Timings
(During Embedded Algorithms)......................................................
Figure 20. Toggle Bit Timings
(During Embedded Algorithms)......................................................
Figure 21. DQ2 vs. DQ6.................................................................
41
41
42
43
44
44
Temporary Sector Unprotect .................................................. 45
Figure 22. Temporary Sector Group Unprotect Timing Diagram ... 45
Figure 23. Sector Group Protect and Unprotect Timing Diagram .. 46
Alternate CE# Controlled Erase and Program Operations ..... 47
Figure 24. Alternate CE# Controlled Write
(Erase/Program) Operation Timings .............................................. 48
Erase And Programming Performance . . . . . . . 49
Latchup Characteristics . . . . . . . . . . . . . . . . . . . . 49
TSOP & FBGA Pin Capacitance. . . . . . . . . . . . . . 49
Data Retention. . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
FBE063—63-Ball Fine-Pitch Ball Grid Array
(FBGA) 11 x 12 mm package ................................................. 50
LAA064–64-Ball Fortified Ball Grid Array (Fortified BGA) 13 x 11
mm package ........................................................................... 51
TS 048—48-Pin Standard TSOP ............................................ 52
Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . 53
Table 10. Command Definitions...................................................... 29
Write Operation Status . . . . . . . . . . . . . . . . . . . . . 30
June 14, 2005
Am29LV641G
6
A D V A N C E
I N F O R M A T I O N
PRODUCT SELECTOR GUIDE
Part Number
Am29LV641G
Regulated Voltage Range VCC = 3.0–3.6 V
Speed Option
55R
Standard Voltage Range VCC = 2.7–3.6 V
70
Max Access Time (ns)
55
70
CE# Access Time (ns)
55
70
OE# Access Time (ns)
35
35
Note: See “AC Characteristics” for full specifications.
BLOCK DIAGRAM
DQ15–DQ0
VCC
Sector Switches
VSS
WE#
WP#
ACC
RY/BY#
VIO
Erase Voltage
Generator
RESET#
State
Control
Command
Register
PGM Voltage
Generator
Chip Enable
Output Enable
Logic
CE#
OE#
VCC Detector
Address Latch
STB
Timer
A21–A0
7
Input/Output
Buffers
Am29LV641G
STB
Data
Latch
Y-Decoder
Y-Gating
X-Decoder
Cell Matrix
June 14, 2005
A D V A N C E
I N F O R M A T I O N
CONNECTION DIAGRAMS
A15
A14
A13
A12
A11
A10
A9
A8
A21
A20
WE#
RESET#
ACC
WP#
A19
A18
A17
A7
A6
A5
A4
A3
A2
A1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
A16
VIO
VSS
DQ15
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
VSS
CE#
A0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
June 14, 2005
48-Pin Standard TSOP
48-Pin Reverse TSOP
Am29LV641G
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
A16
VIO
VSS
DQ15
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
VSS
CE#
A0
A15
A14
A13
A12
A11
A10
A9
A8
A21
A20
WE#
RESET#
ACC
WP#
A19
A18
A17
A7
A6
A5
A4
A3
A2
A1
8
A D V A N C E
I N F O R M A T I O N
CONNECTION DIAGRAMS
A8
B8
NC
NC
A7
B7
NC
NC
A2
63-Ball FBGA
Top View, Balls Facing Down
C7
A1
B1
NC*
NC*
E7
F7
G7
H7
M8
NC*
NC*
J7
K7
L7
M7
NC*
NC*
A13
A12
A14
A15
A16
VIO
DQ15
VSS
C6
D6
E6
F6
G6
H6
J6
K6
A9
A8
A10
A11
DQ7
DQ14
DQ13
DQ6
C5
D5
E5
F5
G5
H5
J5
K5
WE#
RESET#
A21
A19
DQ5
DQ12
VCC
DQ4
C4
D4
E4
F4
G4
H4
J4
K4
RY/BY#
ACC
A18
A20
DQ2
DQ10
DQ11
DQ3
C3
D3
E3
F3
G3
H3
J3
K3
A7
A17
A6
A5
DQ0
DQ8
DQ9
DQ1
C2
D2
E2
F2
G2
H2
J2
K2
L2
M2
OE#
VSS
NC*
NC*
A3
NC*
D7
L8
A4
A2
A1
A0
CE#
L1
M1
NC*
NC*
* Balls are shorted together via the substrate but not connected to the die.
9
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
CONNECTION DIAGRAMS
64-Ball Fortified BGA
Top View, Balls Facing Down
A8
B8
C8
D8
E8
F8
G8
H8
RFU
RFU
RFU
VIO
VSS
RFU
RFU
RFU
A7
B7
C7
D7
E7
F7
G7
H7
A13
A12
A14
A15
A16
BYTE#
DQ15
VSS
A6
B6
C6
D6
E6
F6
G6
H6
A9
A8
A10
A11
DQ7
DQ14
DQ13
DQ6
A5
B5
C5
D5
E5
F5
G5
H5
WE#
RESET#
A21
A19
DQ5
DQ12
VCC
DQ4
A4
B4
C4
D4
E4
F4
G4
H4
A18
A20
DQ2
DQ10
DQ11
DQ3
RY/BY# WP#/ACC
A3
B3
C3
D3
E3
F3
G3
H3
A7
A17
A6
A5
DQ0
DQ8
DQ9
DQ1
A2
B2
C2
D2
E2
F2
G2
H2
A3
A4
A2
A1
A0
CE#
OE#
VSS
A1
B1
C1
D1
E1
F1
G1
H1
RFU
RFU
RFU
RFU
RFU
VIO
RFU
RFU
Special Package Handling Instructions
Special handling is required for Flash Memory products
in molded packages (TSOP and BGA) The package
June 14, 2005
and/or data integrity may be compromised if the package
body is exposed to temperatures above 150°C for prolonged periods of time.
Am29LV641G
10
A D V A N C E
PIN DESCRIPTION
A21–A0
= 22 Addresses inputs
I N F O R M A T I O N
LOGIC SYMBOL
22
DQ15–DQ0 = 16 Data inputs/outputs
CE#
= Chip Enable input
OE#
= Output Enable input
WE#
= Write Enable input
WP#
= Hardware Write Protect input
ACC
= Acceleration Input
RY/BY#
= Ready/Busy output
RESET#
= Hardware Reset Pin input
VCC
= 3.0 volt-only single power supply
(see Product Selector Guide for
speed options and voltage
supply tolerances)
VIO
= Output Buffer power
VSS
= Device Ground
NC
= Pin Not Connected Internally
A21–A0
CE#
16
DQ15–DQ0
OE#
WE#
WP#
ACC
RESET#
RY/BY#
VIO
Note:WP#/ACC functionality is multiplexed for
Am29LV641GH/L devices. RY/BY# available only for
Am29LV640GU devices.
11
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
ORDERING INFORMATION
Standard Products
AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is
formed by a combination of the following:
Am29LV641G
H
55R
WH
I
TEMPERATURE RANGE
I
= Industrial (–40°C to +85°C)
PACKAGE TYPE
E
= 48-Pin Thin Small Outline Package (TSOP) Standard Pinout (TS 048)
F
= 48-Pin Thin Small Outline Package (TSOP) Reverse Pinout (TSR048)
WH = 63-Ball Fine-Pitch Ball Grid Array (FBGA)
0.80 mm pitch, 11 x 12 mm package (FBE063)
PC = 64-Ball Fine-Pitch Ball Grid Array (Fortified BGA)
1.0 mm pitch, 13 x 11 mm package (LAA064)
SPEED OPTION
See Product Selector Guide and Valid Combinations
SECTOR ARCHITECTURE AND SECTOR WRITE PROTECTION (WP# = 0)
H
= Uniform sector device, highest address sector protected
L
= Uniform sector device, lowest address sector protected
DEVICE NUMBER/DESCRIPTION
Am29LV641G
64 Megabit (4 M x 16-Bit) CMOS Uniform Sector Flash Memory with VersatileIO™ Control
3.0 Volt-only Read, Program, and Erase
Valid Combinations for
TSOP and SSOP Packages
Am29LV641GH73,
Am29LV641GL73
Am29LV641GH53R,
Am29LV641GL53R
EI, FI
Valid Combinations for FBGA Packages
Speed/VIO Range
70 ns
VIO = 2.7 V – 3.6 V
55 ns
VIO = 3.0 V – 3.6 V
Marking Converstion
For the Am29LV641GH/L/AmLV640GU Enhanced-VIO device,
the last digit of the speed indicator specifies VIO range. Speed
grades ending in 3 (e.g. 93, 103, etc.) indicate a 3 Volt VIO
range; speed grades ending in 8 (e.g. 98, 108, etc.) indicate a
1.8 V VIO range.
Package
Marking
Order Number
Am29LV640GU53R
L640GU53R
55ns
VIO = 3.0V –
3.6 V
L640GU73V
70 ns
VIO = 2.7 V –
3.6 V
WHI
Am29LV640GU73
I
Am29LV640GU53R
L640GU53N
55 ns
VIO = 3.0 V –
3.6 V
L640GU73P
70 ns
VIO = 2.7 V –
3.6 V
PCI
Am29LV640GU73
Speed/
VIO Range
Valid Combinations
Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales
office to confirm availability of specific valid combinations and
to check on newly released combinations.
June 14, 2005
Am29LV641G
12
A D V A N C E
I N F O R M A T I O N
DEVICE BUS OPERATIONS
This section describes the requirements and use of
the device bus operations, which are initiated through
the internal command register. The command register
itself does not occupy any addressable memory location. The register is a latch used to store the commands, along with the address and data information
needed to execute the command. The contents of the
Table 1.
register serve as inputs to the internal state machine.
The state machine outputs dictate the function of the
device. Table 1 lists the device bus operations, the inputs and control levels they require, and the resulting
output. The following subsections describe each of
these operations in further detail.
Device Bus Operations
CE#
OE#
WE#
RESET#
ACC
Addresses
(Note 2)
DQ15–
DQ0
Read
L
L
H
H
X
AIN
DOUT
Write (Program/Erase)
L
H
L
H
X
AIN
(Note 4)
Accelerated Program
L
H
L
H
VHH
AIN
(Note 4)
VCC ±
0.3 V
X
X
VCC ±
0.3 V
H
X
High-Z
Output Disable
L
H
H
H
X
X
High-Z
Reset
X
X
X
L
X
X
High-Z
Sector Group Protect (Note 2)
L
H
L
VID
X
SA, A6 = L,
A1 = H, A0 = L
(Note 4)
Sector Group Unprotect
(Note 2)
L
H
L
VID
X
SA, A6 = H,
A1 = H, A0 = L
(Note 4)
Temporary Sector Group
Unprotect
X
X
X
VID
X
AIN
(Note 4)
Operation
Standby
Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 8.5–12.5 V, VHH = 11.5–12.5 V, X = Don’t Care, SA = Sector Address,
AIN = Address In, DIN = Data In, DOUT = Data Out
Notes:
1. Addresses are A21:A0. Sector addresses are A21:A15.
2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See the “Sector Group
Protection and Unprotection” section.
3. All sectors are unprotected when shipped from the factory (The SecSi Sector may be factory protected depending on version
ordered.)
4. DIN or DOUT as required by command sequence, data polling, or sector protect algorithm (see Figure 2).
VersatileI/O™ (VIO) Control
Requirements for Reading Array Data
The VersatileI/O (VIO) control allows the host system
to set the voltage levels that the device generates at
its data outputs and the voltages tolerated at its data
inputs to the same voltage level that is asserted on the
VIO pin. This allows the device to operate in 1.8 V or 3
V system environment as required.
To read array data from the outputs, the system must
drive the CE# and OE# pins to VIL. CE# is the power
control and selects the device. OE# is the output control and gates array data to the output pins. WE#
should remain at VIH.
For example, a VI/O of 1.65–1.95 volts allows for I/O at
the 3 volt level, driving and receiving signals to and
from other 3 V devices on the same bus.
13
The internal state machine is set for reading array data
upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory
content occurs during the power transition. No command is necessary in this mode to obtain array data.
Standard microprocessor read cycles that assert valid
addresses on the device address inputs produce valid
data on the device data outputs. The device remains
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
enabled for read access until the command register
contents are altered.
See “Requirements for Reading Array Data” for more
information. Refer to the AC Read-Only Operations
table for timing specifications and to Figure 14 for the
timing diagram. ICC1 in the DC Characteristics table
represents the active current specification for reading
array data.
Writing Commands/Command Sequences
To write a command or command sequence (which includes programming data to the device and erasing
sectors of memory), the system must drive WE# and
CE# to VIL, and OE# to VIH.
The device features an Unlock Bypass mode to facilitate faster programming. Once the device enters the
Unlock Bypass mode, only two write cycles are required to program a word, instead of four. The “Word
Program Command Sequence” section has details on
programming data to the device using both standard
and Unlock Bypass command sequences.
An erase operation can erase one sector, multiple sectors, or the entire device. Table 2 indicates the address
space that each sector occupies.
ICC2 in the DC Characteristics table represents the active current specification for the write mode. The AC
Characteristics section contains timing specification
tables and timing diagrams for write operations.
Accelerated Program Operation
The device offers accelerated program operations
through the ACC function. This function is primarily intended to allow faster manufacturing throughput during system production.
If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass
mode, temporarily unprotects any protected sectors,
and uses the higher voltage on the pin to reduce the
time required for program operations. The system
would use a two-cycle program command sequence
as required by the Unlock Bypass mode. Removing
VHH from the ACC pin returns the device to normal operation. Note that the ACC pin must not be at VHH for
operations other than accelerated programming, or
device damage may result.
Autoselect Functions
If the system writes the autoselect command sequence, the device enters the autoselect mode. The
system can then read autoselect codes from the internal register (which is separate from the memory array)
on DQ7–DQ0. Standard read cycle timings apply in
this mode. Refer to the Autoselect Mode and Autoselect Command Sequence sections for more information.
June 14, 2005
Standby Mode
When the system is not reading or writing to the device, it can place the device in the standby mode. In
this mode, current consumption is greatly reduced,
and the outputs are placed in the high impedance
state, independent of the OE# input.
The device enters the CMOS standby mode when the
CE# and RESET# pins are both held at VCC ± 0.3 V.
(Note that this is a more restricted voltage range than
VIH.) If CE# and RESET# are held at VIH, but not within
VCC ± 0.3 V, the device will be in the standby mode,
but the standby current will be greater. The device requires standard access time (t CE ) for read access
when the device is in either of these standby modes,
before it is ready to read data.
If the device is deselected during erasure or programming, the device draws active current until the
operation is completed.
I CC3 in the DC Characteristics table represents the
standby current specification.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables
this mode when addresses remain stable for t ACC +
30 ns. The automatic sleep mode is independent of
the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output
data is latched and always available to the system.
I CC4 in the DC Characteristics table represents the
automatic sleep mode current specification.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of resetting the device to reading array data. When the RESET# pin is driven low for at least a period of tRP, the
device immediately terminates any operation in
progress, tristates all output pins, and ignores all
read/write commands for the duration of the RESET#
pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is
ready to accept another command sequence, to ensure data integrity.
Current is reduced for the duration of the RESET#
pulse. When RESET# is held at VSS±0.3 V, the device
draws CMOS standby current (ICC4). If RESET# is held
at VIL but not within VSS±0.3 V, the standby current will
be greater.
The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the Flash
memory, enabling the system to read the boot-up firmware from the Flash memory.
Am29LV641G
14
A D V A N C E
I N F O R M A T I O N
Output Disable Mode
Refer to the AC Characteristics tables for RESET# parameters and to Figure 15 for the timing diagram.
Table 2.
15
When the OE# input is at VIH, output from the device is
disabled. The output pins are placed in the high
impedance state.
Sector Address Table
Sector
A21
A20
A19
A18
A17
A16
A15
8-bit Address Range
(in hexadecimal)
16-bit Address Range
(in hexadecimal)
SA0
0
0
0
0
0
0
0
000000–00FFFF
000000–007FFF
SA1
0
0
0
0
0
0
1
010000–01FFFF
008000–00FFFF
SA2
0
0
0
0
0
1
0
020000–02FFFF
010000–017FFF
SA3
0
0
0
0
0
1
1
030000–03FFFF
018000–01FFFF
SA4
0
0
0
0
1
0
0
040000–04FFFF
020000–027FFF
SA5
0
0
0
0
1
0
1
050000–05FFFF
028000–02FFFF
SA6
0
0
0
0
1
1
0
060000–06FFFF
030000–037FFF
SA7
0
0
0
0
1
1
1
070000–07FFFF
038000–03FFFF
SA8
0
0
0
1
0
0
0
080000–08FFFF
040000–047FFF
SA9
0
0
0
1
0
0
1
090000–09FFFF
048000–04FFFF
SA10
0
0
0
1
0
1
0
0A0000–0AFFFF
050000–057FFF
SA11
0
0
0
1
0
1
1
0B0000–0BFFFF
058000–05FFFF
SA12
0
0
0
1
1
0
0
0C0000–0CFFFF
060000–067FFF
SA13
0
0
0
1
1
0
1
0D0000–0DFFFF
068000–06FFFF
SA14
0
0
0
1
1
1
0
0E0000–0EFFFF
070000–077FFF
SA15
0
0
0
1
1
1
1
0F0000–0FFFFF
078000–07FFFF
SA16
0
0
1
0
0
0
0
100000–10FFFF
080000–087FFF
SA17
0
0
1
0
0
0
1
110000–11FFFF
088000–08FFFF
SA18
0
0
1
0
0
1
0
120000–12FFFF
090000–097FFF
SA19
0
0
1
0
0
1
1
130000–13FFFF
098000–09FFFF
SA20
0
0
1
0
1
0
0
140000–14FFFF
0A0000–0A7FFF
SA21
0
0
1
0
1
0
1
150000–15FFFF
0A8000–0AFFFF
SA22
0
0
1
0
1
1
0
160000–16FFFF
0B0000–0B7FFF
SA23
0
0
1
0
1
1
1
170000–17FFFF
0B8000–0BFFFF
SA24
0
0
1
1
0
0
0
180000–18FFFF
0C0000–0C7FFF
SA25
0
0
1
1
0
0
1
190000–19FFFF
0C8000–0CFFFF
SA26
0
0
1
1
0
1
0
1A0000–1AFFFF
0D0000–0D7FFF
SA27
0
0
1
1
0
1
1
1B0000–1BFFFF
0D8000–0DFFFF
SA28
0
0
1
1
1
0
0
1C0000–1CFFFF
0E0000–0E7FFF
SA29
0
0
1
1
1
0
1
1D0000–1DFFFF
0E8000–0EFFFF
SA30
0
0
1
1
1
1
0
1E0000–1EFFFF
0F0000–0F7FFF
Am29LV641G
June 14, 2005
A D V A N C E
Table 2.
I N F O R M A T I O N
Sector Address Table (Continued)
Sector
A21
A20
A19
A18
A17
A16
A15
8-bit Address Range
(in hexadecimal)
16-bit Address Range
(in hexadecimal)
SA31
0
0
1
1
1
1
1
1F0000–1FFFFF
0F8000–0FFFFF
SA32
0
1
0
0
0
0
0
200000–20FFFF
100000–107FFF
SA33
0
1
0
0
0
0
1
210000–21FFFF
108000–10FFFF
SA34
0
1
0
0
0
1
0
220000–22FFFF
110000–117FFF
SA35
0
1
0
0
0
1
1
230000–23FFFF
118000–11FFFF
SA36
0
1
0
0
1
0
0
240000–24FFFF
120000–127FFF
SA37
0
1
0
0
1
0
1
250000–25FFFF
128000–12FFFF
SA38
0
1
0
0
1
1
0
260000–26FFFF
130000–137FFF
SA39
0
1
0
0
1
1
1
270000–27FFFF
138000–13FFFF
SA40
0
1
0
1
0
0
0
280000–28FFFF
140000–147FFF
SA41
0
1
0
1
0
0
1
290000–29FFFF
148000–14FFFF
SA42
0
1
0
1
0
1
0
2A0000–2AFFFF
150000–157FFF
SA43
0
1
0
1
0
1
1
2B0000–2BFFFF
158000–15FFFF
SA44
0
1
0
1
1
0
0
2C0000–2CFFFF
160000–167FFF
SA45
0
1
0
1
1
0
1
2D0000–2DFFFF
168000–16FFFF
SA46
0
1
0
1
1
1
0
2E0000–2EFFFF
170000–177FFF
SA47
0
1
0
1
1
1
1
2F0000–2FFFFF
178000–17FFFF
SA48
0
1
1
0
0
0
0
300000–30FFFF
180000–187FFF
SA49
0
1
1
0
0
0
1
310000–31FFFF
188000–18FFFF
SA50
0
1
1
0
0
1
0
320000–32FFFF
190000–197FFF
SA51
0
1
1
0
0
1
1
330000–33FFFF
198000–19FFFF
SA52
0
1
1
0
1
0
0
340000–34FFFF
1A0000–1A7FFF
SA53
0
1
1
0
1
0
1
350000–35FFFF
1A8000–1AFFFF
SA54
0
1
1
0
1
1
0
360000–36FFFF
1B0000–1B7FFF
SA55
0
1
1
0
1
1
1
370000–37FFFF
1B8000–1BFFFF
SA56
0
1
1
1
0
0
0
380000–38FFFF
1C0000–1C7FFF
SA57
0
1
1
1
0
0
1
390000–39FFFF
1C8000–1CFFFF
SA58
0
1
1
1
0
1
0
3A0000–3AFFFF
1D0000–1D7FFF
SA59
0
1
1
1
0
1
1
3B0000–3BFFFF
1D8000–1DFFFF
SA60
0
1
1
1
1
0
0
3C0000–3CFFFF
1E0000–1E7FFF
SA61
0
1
1
1
1
0
1
3D0000–3DFFFF
1E8000–1EFFFF
SA62
0
1
1
1
1
1
0
3E0000–3EFFFF
1F0000–1F7FFF
SA63
0
1
1
1
1
1
1
3F0000–3FFFFF
1F8000–1FFFFF
SA64
1
0
0
0
0
0
0
400000–40FFFF
200000–207FFF
SA65
1
0
0
0
0
0
1
410000–41FFFF
208000–20FFFF
June 14, 2005
Am29LV641G
16
A D V A N C E
Table 2.
17
I N F O R M A T I O N
Sector Address Table (Continued)
Sector
A21
A20
A19
A18
A17
A16
A15
8-bit Address Range
(in hexadecimal)
16-bit Address Range
(in hexadecimal)
SA66
1
0
0
0
0
1
0
420000–42FFFF
210000–217FFF
SA67
1
0
0
0
0
1
1
430000–43FFFF
218000–21FFFF
SA68
1
0
0
0
1
0
0
440000–44FFFF
220000–227FFF
SA69
1
0
0
0
1
0
1
450000–45FFFF
228000–22FFFF
SA70
1
0
0
0
1
1
0
460000–46FFFF
230000–237FFF
SA71
1
0
0
0
1
1
1
470000–47FFFF
238000–23FFFF
SA72
1
0
0
1
0
0
0
480000–48FFFF
240000–247FFF
SA73
1
0
0
1
0
0
1
490000–49FFFF
248000–24FFFF
SA74
1
0
0
1
0
1
0
4A0000–4AFFFF
250000–257FFF
SA75
1
0
0
1
0
1
1
4B0000–4BFFFF
258000–25FFFF
SA76
1
0
0
1
1
0
0
4C0000–4CFFFF
260000–267FFF
SA77
1
0
0
1
1
0
1
4D0000–4DFFFF
268000–26FFFF
SA78
1
0
0
1
1
1
0
4E0000–4EFFFF
270000–277FFF
SA79
1
0
0
1
1
1
1
4F0000–4FFFFF
278000–27FFFF
SA80
1
0
1
0
0
0
0
500000–50FFFF
280000–287FFF
SA81
1
0
1
0
0
0
1
510000–51FFFF
288000–28FFFF
SA82
1
0
1
0
0
1
0
520000–52FFFF
290000–297FFF
SA83
1
0
1
0
0
1
1
530000–53FFFF
298000–29FFFF
SA84
1
0
1
0
1
0
0
540000–54FFFF
2A0000–2A7FFF
SA85
1
0
1
0
1
0
1
550000–55FFFF
2A8000–2AFFFF
SA86
1
0
1
0
1
1
0
560000–56FFFF
2B0000–2B7FFF
SA87
1
0
1
0
1
1
1
570000–57FFFF
2B8000–2BFFFF
SA88
1
0
1
1
0
0
0
580000–58FFFF
2C0000–2C7FFF
SA89
1
0
1
1
0
0
1
590000–59FFFF
2C8000–2CFFFF
SA90
1
0
1
1
0
1
0
5A0000–5AFFFF
2D0000–2D7FFF
SA91
1
0
1
1
0
1
1
5B0000–5BFFFF
2D8000–2DFFFF
SA92
1
0
1
1
1
0
0
5C0000–5CFFFF
2E0000–2E7FFF
SA93
1
0
1
1
1
0
1
5D0000–5DFFFF
2E8000–2EFFFF
SA94
1
0
1
1
1
1
0
5E0000–5EFFFF
2F0000–2F7FFF
SA95
1
0
1
1
1
1
1
5F0000–5FFFFF
2F8000–2FFFFF
SA96
1
1
0
0
0
0
0
600000–60FFFF
300000–307FFF
SA97
1
1
0
0
0
0
1
610000–61FFFF
308000–30FFFF
SA98
1
1
0
0
0
1
0
620000–62FFFF
310000–317FFF
SA99
1
1
0
0
0
1
1
630000–63FFFF
318000–31FFFF
SA100
1
1
0
0
1
0
0
640000–64FFFF
320000–327FFF
Am29LV641G
June 14, 2005
A D V A N C E
Table 2.
I N F O R M A T I O N
Sector Address Table (Continued)
Sector
A21
A20
A19
A18
A17
A16
A15
8-bit Address Range
(in hexadecimal)
16-bit Address Range
(in hexadecimal)
SA101
1
1
0
0
1
0
1
650000–65FFFF
328000–32FFFF
SA102
1
1
0
0
1
1
0
660000–66FFFF
330000–337FFF
SA103
1
1
0
0
1
1
1
670000–67FFFF
338000–33FFFF
SA104
1
1
0
1
0
0
0
680000–68FFFF
340000–347FFF
SA105
1
1
0
1
0
0
1
690000–69FFFF
348000–34FFFF
SA106
1
1
0
1
0
1
0
6A0000–6AFFFF
350000–357FFF
SA107
1
1
0
1
0
1
1
6B0000–6BFFFF
358000–35FFFF
SA108
1
1
0
1
1
0
0
6C0000–6CFFFF
360000–367FFF
SA109
1
1
0
1
1
0
1
6D0000–6DFFFF
368000–36FFFF
SA110
1
1
0
1
1
1
0
6E0000–6EFFFF
370000–377FFF
SA111
1
1
0
1
1
1
1
6F0000–6FFFFF
378000–37FFFF
SA112
1
1
1
0
0
0
0
700000–70FFFF
380000–387FFF
SA113
1
1
1
0
0
0
1
710000–71FFFF
388000–38FFFF
SA114
1
1
1
0
0
1
0
720000–72FFFF
390000–397FFF
SA115
1
1
1
0
0
1
1
730000–73FFFF
398000–39FFFF
SA116
1
1
1
0
1
0
0
740000–74FFFF
3A0000–3A7FFF
SA117
1
1
1
0
1
0
1
750000–75FFFF
3A8000–3AFFFF
SA118
1
1
1
0
1
1
0
760000–76FFFF
3B0000–3B7FFF
SA119
1
1
1
0
1
1
1
770000–77FFFF
3B8000–3BFFFF
SA120
1
1
1
1
0
0
0
780000–78FFFF
3C0000–3C7FFF
SA121
1
1
1
1
0
0
1
790000–79FFFF
3C8000–3CFFFF
SA122
1
1
1
1
0
1
0
7A0000–7AFFFF
3D0000–3D7FFF
SA123
1
1
1
1
0
1
1
7B0000–7BFFFF
3D8000–3DFFFF
SA124
1
1
1
1
1
0
0
7C0000–7CFFFF
3E0000–3E7FFF
SA125
1
1
1
1
1
0
1
7D0000–7DFFFF
3E8000–3EFFFF
SA126
1
1
1
1
1
1
0
7E0000–7EFFFF
3F0000–3F7FFF
SA127
1
1
1
1
1
1
1
7F0000–7FFFFF
3F8000–3FFFFF
Note: All sectors are 32 Kwords in size.
June 14, 2005
Am29LV641G
18
A D V A N C E
I N F O R M A T I O N
Autoselect Mode
The autoselect mode provides manufacturer and device identification, and sector protection verification,
through identifier codes output on DQ7–DQ0. This
mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programm ing
algorithm. However, the autoselect codes can also be
accessed in-system through the command register.
When using programming equipment, the autoselect
mode requires VID (8.5 V to 12.5 V) on address pin A9.
Address pins A6, A1, and A0 must be as shown in
Table 3.
Table 3. In addition, when verifying sector protection,
the sector address must appear on the appropriate
highest order address bits (see Table 2). Table 3
shows the remaining address bits that are don’t care.
When all necessary bits have been set as required,
the programming equipment may then read the corresponding identifier code on DQ7–DQ0.
To access the autoselect codes in-system, the host
system can issue the autoselect command via the
command register, as shown in Table 10. This method
does not require V ID. Refer to the Autoselect Command Sequence section for more information.
Autoselect Codes, (High Voltage Method)
A14
to
A10
A9
A8
to
A7
A7
to
A0
A6
A5
to
A2
A1
A0
DQ15
to
DQ0
CE#
OE#
WE#
A21
to
A15
L
L
H
X
X
VID
X
—
L
X
L
L
XX01h
Read Cycle 1
L
L
H
X
X
VID
X
—
L
X
L
H
22D7h
Read Cycle 2
L
L
H
X
X
VID
0Eh
L
L
H
220Fh
Read Cycle 3
L
L
H
X
X
VID
0Fh
L
L
H
XX00h
Sector Protection
Verification
L
L
H
SA
X
VID
X
—
L
X
H
L
01h (protected),
00h (unprotected)
SecSi™ Sector
Indicator Bit (DQ7)
L
L
H
X
X
VID
X
—
L
X
H
H
98h (factory locked),
18h (not factory locked)
SecSi™ Sector
Indicator Bit (DQ7),
WP# protects highest
address sector
L
L
H
X
X
VID
X
—
L
X
H
H
XX98h (factory locked),
XX18h (not factory
locked)
SecSi™ Sector
Indicator Bit (DQ7),
WP# protects lowest
address sector
L
L
H
X
X
VID
X
—
L
X
H
H
XX88h (factory locked),
XX08h (not factory
locked)
Description
Autoselect Device Code
Manufacturer ID:
AMD
Legend: L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care.
Note: SecSi™ Sector Indicator Bit (DQ7) exist only in the Am29LV641GH/L devices.
19
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
Sector Group Protection and
Unprotection
Table 4.
Sector Group Protection/Unprotection
Address Table
The hardware sector group protection feature disables
both program and erase operations in any sector
group. In this device, a sector group consists of four
adjacent sectors that are protected or unprotected at
the same time (see Table 4). The hardware sector
group unprotection feature re-enables both program
and erase operations in previously protected sector
groups. Sector group protection/unprotection can be
implemented via two methods.
Sector Group
A21–A17
SA0–SA3
00000
The primary method requires VID on the RESET# pin
only, and can be implemented either in-system or via
programming equipment. Figure 2 shows the algorithms and Figure 23 shows the timing diagram. This
method uses standard microprocessor bus cycle timing. For sector group unprotect, all unprotected sector
groups must first be protected prior to the first sector
group unprotect write cycle.
The alternate method intended only for programming
equipment requires VID on address pin A9 and OE#.
This method is compatible with programmer routines
written for earlier 3.0 volt-only AMD flash devices.
Publication number 22367 contains further details;
contact an AMD representative to request a copy.
SA4–SA7
00001
SA8–SA11
00010
SA12–SA15
00011
SA16–SA19
00100
SA20–SA23
00101
SA24–SA27
00110
SA28–SA31
00111
SA32–SA35
01000
SA36–SA39
01001
SA40–SA43
01010
SA44–SA47
01011
SA48–SA51
01100
SA52–SA55
01101
SA56–SA59
01110
SA60–SA63
01111
SA64–SA67
10000
SA68–SA71
10001
SA72–SA75
10010
The device is shipped with all sector groups unprotected. AMD offers the option of programming and
protecting sector groups at its factory prior to shipping
the device through AMD’s ExpressFlash™ Service.
Contact an AMD representative for details.
SA76–SA79
10011
SA80–SA83
10100
SA84–SA87
10101
SA88–SA91
10110
It is possible to determine whether a sector group is
protected or unprotected. See the Autoselect Mode
section for details.
SA92–SA95
10111
SA96–SA99
11000
SA100–SA103
11001
SA104–SA107
11010
SA108–SA111
11011
SA112–SA115
11100
SA116–SA119
11101
SA120–SA123
11110
SA124–SA127
11111
Note: All sector groups are 128 Kwords in size.
June 14, 2005
Am29LV641G
20
A D V A N C E
I N F O R M A T I O N
Write Protect (WP#)
The Write Protect function provides a hardware
method of protecting the first or last sector without
using VID.
START
If the system asserts VIL on the WP# pin, the device
disables program and erase functions in the first or
last sector independently of whether those sectors
were protected or unprotected using the method described in “Sector Group Protection and Unprotection”.
Note that if WP# is at V IL when the device is in the
standby mode, the maximum input load current is increased. See the table in “DC Characteristics”.
RESET# = VID
(Note 1)
Perform Erase or
Program Operations
RESET# = VIH
If the system asserts VIH on the WP# pin, the device
reverts to whether the first or last sector was previously set to be protected or unprotected using the
method described in “Sector Group Protection and
Unprotection”.
Temporary Sector
Group Unprotect
Completed (Note 2)
Temporary Sector Group Unprotect
(Note: In this device, a sector group consists of four adjacent
sectors that are protected or unprotected at the same time
(see Table 4)).
This feature allows temporary unprotection of previously protected sector groups to change data in-system. The Sector Group Unprotect mode is activated by
setting the RESET# pin to VID (8.5 V – 12.5 V). During
this mode, formerly protected sector groups can be
programmed or erased by selecting the sector group
addresses. Once V ID is removed from the RESET#
pin, all the previously protected sector groups are
protected again. Figure 1 shows the algorithm, and
Figure 22 shows the timing diagrams, for this feature.
21
Notes:
1. All protected sector groups unprotected (If WP# = VIL,
the first or last sector will remain protected).
2. All previously protected sector groups are protected
once again.
Am29LV641G
Figure 1. Temporary Sector Group
Unprotect Operation
June 14, 2005
A D V A N C E
I N F O R M A T I O N
START
START
PLSCNT = 1
RESET# = VID
Wait 1 μs
Temporary Sector
Group Unprotect
Mode
No
PLSCNT = 1
Protect all sector
groups: The indicated
portion of the sector
group protect algorithm
must be performed for all
unprotected sector
groups prior to issuing
the first sector group
unprotect address
RESET# = VID
Wait 1 μs
First Write
Cycle = 60h?
First Write
Cycle = 60h?
Temporary Sector
Group Unprotect
Mode
Yes
Yes
Set up sector
group address
No
Sector Group Protect:
Write 60h to sector
group address with
A6 = 0, A1 = 1,
A0 = 0
All sector
groups
protected?
Yes
Set up first sector
group address
Sector Group
Unprotect:
Write 60h to sector
group address with
A6 = 1, A1 = 1,
A0 = 0
Wait 150 µs
Increment
PLSCNT
No
Verify Sector Group
Protect: Write 40h
to sector group
address twith A6 = 0,
A1 = 1, A0 = 0
Reset
PLSCNT = 1
Wait 15 ms
Read from
sector group address
with A6 = 0,
A1 = 1, A0 = 0
Verify Sector Group
Unprotect: Write
40h to sector group
address with
A6 = 1, A1 = 1,
A0 = 0
Increment
PLSCNT
No
No
PLSCNT
= 25?
Read from
sector group
address with A6 = 1,
A1 = 1, A0 = 0
Data = 01h?
Yes
No
Yes
Device failed
Protect
another
sector group?
Yes
No
PLSCNT
= 1000?
No
Yes
Remove VID
from RESET#
Device failed
Write reset
command
Sector Group
Protect
Algorithm
Set up
next sector group
address
Data = 00h?
Yes
Last sector
group
verified?
No
Yes
Sector Group
Protect complete
Sector Group
Unprotect
Algorithm
Remove VID
from RESET#
Write reset
command
Sector Group
Unprotect complete
Figure 2.
June 14, 2005
In-System Sector Group Protect/Unprotect Algorithms
Am29LV641G
22
A D V A N C E
I N F O R M A T I O N
SecSi™ (Secured Silicon) Sector Flash
Memory Region
or following a hardware reset, the device reverts to
sending commands to sector SA0.
The SecSi (Secured Silicon) Sector feature provides a
Flash memory region that enables permanent part
identification through an Electronic Serial Number
(ESN). The SecSi Sector is 128 words in length, and
uses a SecSi Sector Indicator Bit (DQ7) to indicate
whether or not the SecSi Sector is locked when
shipped from the factory. This bit is permanently set at
the factory and cannot be changed, which prevents
cloning of a factory locked part. This ensures the security of the ESN once the product is shipped to the field.
Factory Locked: SecSi Sector Programmed and
Protected At the Factory
AMD offers the device with the SecSi Sector either
fac t or y l ocke d or c u s t om e r l o ck abl e. T he fac tory-locked version is always protected when shipped
from the factory, and has the SecSi (Secured Silicon)
Sector Indicator Bit permanently set to a “1.” The customer-lockable version is shipped with the SecSi Sector unprotected, allowing customers to utilize that
sector in any manner they choose. The customer-lockable version also has the SecSi Sector Indicator Bit
permanently set to a “0.” Thus, the SecSi Sector Indicator Bit prevents customer-lockable devices from
being used to replace devices that are factory locked.
The SecSi sector address space in this device is allocated as follows:
Table 5.
SecSi Sector
Address Range
SecSi Sector Contents
Standard
ExpressFlash
Factory Locked Factory Locked
000000h–000007h
ESN
ESN or
determined by
customer
000008h–00007Fh
Unavailable
Determined by
customer
Customer
Lockable
Determined by
customer
*All Uniform Devices (not including Uniform High) such as Am29LV640GU
has its Sector starting at address 0.
The system accesses the SecSi Sector through a
command sequence (see “Enter SecSi Sector/Exit
SecSi Sector Command Sequence”). After the system
has written the Enter SecSi Sector command sequence, it may read the SecSi Sector by using the addresses normally occupied by the first sector (SA0).
This mode of operation continues until the system issues the Exit SecSi Sector command sequence, or
until power is removed from the device. On power-up,
23
In devices with an ESN, the SecSi Sector is protected
when the device is shipped from the factory. The SecSi
Sector cannot be modified in any way. A factory locked
device has an 8-word random ESN at addresses
000000h–000007h.
Customers may opt to have their code programmed by
AMD through the AMD ExpressFlash service. The devices are then shipped from AMD’s factory with the
SecSi Sector permanently locked. Contact an AMD
representative for details on using AMD’s ExpressFlash service.
Customer Lockable: SecSi Sector NOT
Programmed or Protected At the Factory
As an alternative to the factory-locked version, the device may be ordered such that the customer may progra m an d p r ot ec t t he 12 8 - wo rd Se cS i se ct or.
Programming and protecting the SecSi Sector must be
used with caution since, once protected, there is no
procedure available for unprotecting the SecSi Sector
area and none of the bits in the SecSi Sector memory
space can be modified in any way.
The SecSi Sector area can be protected using one of
the following procedures:
■ Write the three-cycle Enter SecSi Sector Region
command sequence, and then follow the in-system
sector protect algorithm as shown in Figure 2, except that RESET# may be at either VIH or VID. This
allows in-system protection of the SecSi Sector
without raising any device pin to a high voltage.
Note that this method is only applicable to the SecSi
Sector.
■ Write the three-cycle Enter SecSi Sector Region
command sequence, and then use the alternate
method of sector protection described in the “Sector
Group Protection and Unprotection” section.
Once the SecSi Sector is programmed, locked and
verified, the system must write the Exit SecSi Sector
Region command sequence to return to reading and
writing within the remainder of the array.
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
data protection measures prevent accidental erasure
or programming, which might otherwise be caused by
spurious system level signals during V CC power-up
and power-down transitions, or from system noise.
START
RESET# =
VIH or VID
Wait 1 μs
Write 60h to
any address
Write 40h to SecSi
Sector address
with A6 = 0,
A1 = 1, A0 = 0
Read from SecSi
Sector address
with A6 = 0,
A1 = 1, A0 = 0
Low VCC Write Inhibit
If data = 00h,
SecSi Sector is
unprotected.
If data = 01h,
SecSi Sector is
protected.
When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC
power-up and power-down. The command register
and all internal program/erase circuits are disabled,
and the device resets to the read mode. Subsequent
writes are ignored until VCC is greater than VLKO. The
system must provide the proper signals to the control
pins to prevent unintentional writes when V CC is
greater than VLKO.
Remove VIH or VID
from RESET#
Write reset
command
Write Pulse “Glitch” Protection
Noise pulses of less than 5 ns (typical) on OE#, CE#
or WE# do not initiate a write cycle.
SecSi Sector
Protect Verify
complete
Logical Inhibit
Write cycles are inhibited by holding any one of OE# =
VIL, CE# = VIH or WE# = VIH. To initiate a write cycle,
CE# and WE# must be a logical zero while OE# is a
logical one.
Figure 3.
SecSi Sector Protect Verify
Power-Up Write Inhibit
Hardware Data Protection
The command sequence requirement of unlock cycles
for programming or erasing provides data protection
against inadvertent writes (refer to Table 10 for command definitions). In addition, the following hardware
If WE# = CE# = VIL and OE# = V IH during power up,
the device does not accept commands on the rising
edge of WE#. The internal state machine is automatically reset to the read mode on power-up.
COMMON FLASH MEMORY INTERFACE (CFI)
The Common Flash Interface (CFI) specification outlines device and host system software interrogation
handshake, which allows specific vendor-specified
software algorithms to be used for entire families of
devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and
backward-compatible for the specified flash device
families. Flash vendors can standardize their existing
interfaces for long-term compatibility.
CFI data at the addresses given in Tables 6–9. The
system must write the reset command to return the
device to reading array data.
For further information, please refer to the CFI Specification and CFI Publication 100, available via the
World Wide Web at http://www.amd.com/flash/cfi. Alternatively, contact an AMD representative for copies
of these documents.
This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address
55h, any time the device is ready to read array data.
The system can read CFI information at the addresses
given in Tables 6–9. To terminate reading CFI data,
the system must write the reset command.
The system can also write the CFI query command
when the device is in the autoselect mode. The device
enters the CFI query mode, and the system can read
June 14, 2005
Am29LV641G
24
A D V A N C E
Table 6.
I N F O R M A T I O N
CFI Query Identification String
Addresses (x16)
Data
Description
10h
11h
12h
0051h
0052h
0059h
Query Unique ASCII string “QRY”
13h
14h
0002h
0000h
Primary OEM Command Set
15h
16h
0040h
0000h
Address for Primary Extended Table
17h
18h
0000h
0000h
Alternate OEM Command Set (00h = none exists)
19h
1Ah
0000h
0000h
Address for Alternate OEM Extended Table (00h = none exists)
Table 7.
System Interface String
Addresses (x16)
Data
Description
1Bh
0027h
VCC Min. (write/erase)
D7–D4: volt, D3–D0: 100 millivolt
1Ch
0036h
VCC Max. (write/erase)
D7–D4: volt, D3–D0: 100 millivolt
1Dh
0000h
VPP Min. voltage (00h = no VPP pin present)
1Eh
0000h
VPP Max. voltage (00h = no VPP pin present)
1Fh
0003h
Typical timeout per single byte/word write 2N µs
20h
0000h
Typical timeout for Min. size buffer write 2N µs (00h = not supported)
21h
000Ah
Typical timeout per individual block erase 2N ms
22h
0000h
Typical timeout for full chip erase 2N ms (00h = not supported)
23h
0005h
Max. timeout for byte/word write 2N times typical
24h
0000h
Max. timeout for buffer write 2N times typical
25h
0002h
Max. timeout per individual block erase 2N times typical
26h
0000h
Max. timeout for full chip erase 2N times typical (00h = not supported)
Table 8.
Device Geometry Definition
Addresses (x16)
Data
27h
0017h
Device Size = 2N byte
28h
29h
0001h
0000h
Flash Device Interface description (refer to CFI publication 100)
2Ah
2Bh
0000h
0000h
Max. number of byte in multi-byte write = 2N
(00h = not supported)
2Ch
0002h
Number of Erase Block Regions within device
2Dh
2Eh
2Fh
30h
0007h
0000h
0020h
0000h
Erase Block Region 1 Information
(refer to the CFI specification or CFI publication 100)
25
Description
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
31h
32h
33h
34h
007Eh
0000h
0000h
0001h
Erase Block Region 2 Information (refer to CFI publication 100)
35h
36h
37h
38h
0000h
0000h
0000h
0000h
Erase Block Region 3 Information (refer to CFI publication 100)
39h
3Ah
3Bh
3Ch
0000h
0000h
0000h
0000h
Erase Block Region 4 Information (refer to CFI publication 100)
June 14, 2005
Am29LV641G
26
A D V A N C E
Table 9.
I N F O R M A T I O N
Primary Vendor-Specific Extended Query
Addresses (x16)
Data
Description
40h
41h
42h
0050h
0052h
0049h
Query-unique ASCII string “PRI”
43h
0031h
Major version number, ASCII
44h
0033h
Minor version number, ASCII
45h
0004h
Address Sensitive Unlock (Bits 1-0)
0 = Required, 1 = Not Required
Silicon Revision Number (Bits 5-2)
46h
0002h
Erase Suspend
0 = Not Supported, 1 = To Read Only, 2 = To Read & Write
47h
0004h
Sector Protect
0 = Not Supported, X = Number of sectors in per group
48h
0001h
Sector Temporary Unprotect
00 = Not Supported, 01 = Supported
49h
0004h
Sector Protect/Unprotect scheme
04 = 29LV800 mode
4Ah
0000h
Simultaneous Operation
00 = Not Supported, X = Number of Sectors in Bank
4Bh
0000h
Burst Mode Type
00 = Not Supported, 01 = Supported
4Ch
0000h
Page Mode Type
00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page
4Dh
00B5h
4Eh
00C5h
4Fh
00XXh
ACC (Acceleration) Supply Minimum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
ACC (Acceleration) Supply Maximum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
00h = Uniform sector device
COMMAND DEFINITIONS
Writing specific address and data commands or sequences into the command register initiates device operations. Table 10 defines the valid register command
sequences. Writing incorrect address and data values or writing them in the improper sequence may
place the device in an unknown state. A reset command is then required to return the device to reading
array data.
All addresses are latched on the falling edge of WE#
or CE#, whichever happens later. All data is latched on
the rising edge of WE# or CE#, whichever happens
first. Refer to the AC Characteristics section for timing
diagrams.
Reading Array Data
The device is automatically set to reading array data
after device power-up. No commands are required to
27
retrieve data. The device is ready to read array data
after completing an Embedded Program or Embedded
Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the erase-suspend-read mode, after
which the system can read data from any
non-erase-suspended sector. After completing a programming operation in the Erase Suspend mode, the
system may once again read array data with the same
exception. See the Erase Suspend/Erase Resume
Commands section for more information.
The system must issue the reset command to return
the device to the read (or erase-suspend-read) mode
if DQ5 goes high during an active program or erase
operation, or if the device is in the autoselect mode.
See the next section, Reset Command, for more information.
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
See also Requirements for Reading Array Data in the
Device Bus Operations section for more information.
The Read-Only Operations table provides the read parameters, and Figure 14 shows the timing diagram.
■ A read cycle at address XX00h returns the manufacturer code.
Reset Command
■ A read cycle to an address containing a sector
group address (SA), and the address 02h on A7–A0
in word mode returns 01h if the sector group is protected, or 00h if it is unprotected. (Refer to Table 4
for valid sector addresses).
Writing the reset command resets the device to the
read or erase-suspend-read mode. Address bits are
don’t cares for this command.
The reset command may be written between the sequence cycles in an erase command sequence before
erasing begins. This resets the device to the read
mode. Once erasure begins, however, the device ignores reset commands until the operation is complete.
The reset command may be written between the
sequence cycles in a program command sequence
before programming begins. This resets the device to
the read mode. If the program command sequence is
written while the device is in the Erase Suspend mode,
writing the reset command returns the device to the
erase-suspend-read mode. Once programming begins, however, the device ignores reset commands
until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect command sequence.
Once in the autoselect mode, the reset command
must be written to return to the read mode. If the device entered the autoselect mode while in the Erase
Suspend mode, writing the reset command returns the
device to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation,
writing the reset command returns the device to the
read mode (or erase-suspend-read mode if the device
was in Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host
system to access the manufacturer and device codes,
and determine whether or not a sector is protected.
Table 10 shows the address and data requirements.
This method is an alternative to that shown in Table 3,
which is intended for PROM programmers and requires V ID on address pin A9. The autoselect command sequence may be written to an address that is
either in the read or erase-suspend-read mode. The
autoselect command may not be written while the device is actively programming or erasing.
The autoselect command sequence is initiated by first
writing two unlock cycles. This is followed by a third
write cycle that contains the autoselect command. The
device then enters the autoselect mode. The system
may read at any address any number of times without
initiating another autoselect command sequence:
June 14, 2005
■ A read cycle at address XX01h returns the device
code.
The system must write the reset command to return to
the read mode (or erase-suspend-read mode if the device was previously in Erase Suspend).
Enter SecSi Sector/Exit SecSi Sector
Command Sequence
The SecSi Sector region provides a secured data area
containing an 8-word random Electronic Serial Number (ESN). The system can access the SecSi Sector
region by issuing the three-cycle Enter SecSi Sector
command sequence. The device continues to access
the SecSi Sector region until the system issues the
four-cycle Exit SecSi Sector command sequence. The
Exit SecSi Sector command sequence returns the device to normal operation. Table 10 shows the address
and data requirements for both command sequences.
See also “SecSi ™ (Secured Silicon) Sector Flash
Memory Region” for further information.
Word Program Command Sequence
Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two
unlock write cycles, followed by the program set-up
command. The program address and data are written
next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further
controls or timings. The device automatically provides
internally generated program pulses and verifies the
programmed cell margin. Table 10 shows the address
and data requirements for the word program command
sequence.
When the Embedded Program algorithm is complete,
the device then returns to the read mode and addresses are no longer latched. The system can determine the status of the program operation by using
DQ7 or DQ6. Refer to the Write Operation Status section for information on these status bits.
Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a
hardware reset immediately terminates the program
operation. The program command sequence should
be reinitiated once the device has returned to the read
mode, to ensure data integrity.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed
Am29LV641G
28
A D V A N C E
I N F O R M A T I O N
from “0” back to a “1.” Attempting to do so may
cause the device to set DQ5 = 1, or cause the DQ7
and DQ6 status bits to indicate the operation was successful. However, a succeeding read will show that the
data is still “0.” Only erase operations can convert a
“0” to a “1.”
START
Unlock Bypass Command Sequence
Write Program
Command Sequence
The unlock bypass feature allows the system to program words to the device faster than using the standard program command sequence. The unlock
bypass command sequence is initiated by first writing
two unlock cycles. This is followed by a third write
cycle containing the unlock bypass command, 20h.
The device then enters the unlock bypass mode. A
two-cycle unlock bypass program command sequence
is all that is required to program in this mode. The first
cycle in this sequence contains the unlock bypass program command, A0h; the second cycle contains the
program address and data. Additional data is programmed in the same manner. This mode dispenses
with the initial two unlock cycles required in the standard program command sequence, resulting in faster
total programming time. Table 10 shows the requirements for the command sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands
are valid. To exit the unlock bypass mode, the system
must issue the two-cycle unlock bypass reset command sequence. The first cycle must contain the data
90h. The second cycle must contain the data 00h. The
device then returns to the read mode.
The device offers accelerated program operations
through the ACC pin. When the system asserts VHH on
the ACC pin, the device automatically enters the Unlock Bypass mode. The system may then write the
two-cycle Unlock Bypass program command sequence. The device uses the higher voltage on the
ACC pin to accelerate the operation. Note that the
ACC pin must not be at VHH for operations other than
accelerated programming, or device damage may result.
Figure 4 illustrates the algorithm for the program operation. Refer to the Erase and Program Operations
table in the AC Characteristics section for parameters,
and Figure 16 for timing diagrams.
29
Data Poll
from System
Embedded
Program
algorithm
in progress
Verify Data?
No
Yes
Increment Address
No
Last Address?
Yes
Programming
Completed
Note: See Table 10 for program command sequence.
Figure 4.
Program Operation
Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase
command sequence is initiated by writing two unlock
cycles, followed by a set-up command. Two additional
unlock write cycles are then followed by the chip erase
command, which in turn invokes the Embedded Erase
algorithm. The device does not require the system to
preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire
memory for an all zero data pattern prior to electrical
erase. The system is not required to provide any controls or timings during these operations. Table 10
shows the address and data requirements for the chip
erase command sequence.
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
When the Embedded Erase algorithm is complete, the
device returns to the read mode and addresses are no
longer latched. The system can determine the status
of the erase operation by using DQ7, DQ6 or DQ2.
Refer to the Write Operation Status section for information on these status bits.
Any commands written during the chip erase operation
are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase command sequence should be
reinitiated once the device has returned to reading
array data, to ensure data integrity.
Figure 5 illustrates the algorithm for the erase operation. Refer to the Erase and Program Operations tables in the AC Characteristics section for parameters,
and Figure 18 section for timing diagrams.
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector
erase command sequence is initiated by writing two
unlock cycles, followed by a set-up command. Two additional unlock cycles are written, and are then followed by the address of the sector to be erased, and
the sector erase command. Table 10 shows the address and data requirements for the sector erase command sequence.
The device does not require the system to preprogram
prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for
an all zero data pattern prior to electrical erase. The
system is not required to provide any controls or timings during these operations.
When the Embedded Erase algorithm is complete, the
device returns to reading array data and addresses
are no longer latched. Note that while the Embedded
Erase operation is in progress, the system can read
data from the non-erasing sector. The system can determine the status of the erase operation by reading
DQ7, DQ6, or DQ2 in the erasing sector. Refer to the
Write Operation Status section for information on
these status bits.
Once the sector erase operation has begun, only the
Erase Suspend command is valid. All other commands are ignored. However, note that a hardware
reset immediately terminates the erase operation. If
that occurs, the sector erase command sequence
should be reinitiated once the device has returned to
reading array data, to ensure data integrity.
Figure 5 illustrates the algorithm for the erase operation. Refer to the Erase and Program Operations tables in the AC Characteristics section for parameters,
and Figure 18 section for timing diagrams.
Erase Suspend/Erase Resume
Commands
The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and then read
data from, or program data to, any sector not selected
for erasure. This command is valid only during the
sector erase operation, including the 50 µs time-out
period during the sector erase command sequence.
The Erase Suspend command is ignored if written during the chip erase operation or Embedded Program
algorithm.
After the command sequence is written, a sector erase
time-out of 50 µs occurs. During the time-out period,
additional sector addresses and sector erase commands may be written. Loading the sector erase buffer
may be done in any sequence, and the number of sectors may be from one sector to all sectors. The time
between these additional cycles must be less than 50
µs, otherwise erasure may begin. Any sector erase
address and command following the exceeded
time-out may or may not be accepted. It is recommended that processor interrupts be disabled during
this time to ensure all commands are accepted. The
interrupts can be re-enabled after the last Sector
Erase command is written. Any command other than
S e ct o r E ra se o r E ra s e S u sp en d d u r in g th e
time-out period resets the device to the read
mode. The system must rewrite the command sequence and any additional addresses and commands.
When the Erase Suspend command is written during
the sector erase operation, the device requires a maximum of 20 µs to suspend the erase operation. However, when the Erase Suspend command is written
during the sector erase time-out, the device immediately terminates the time-out period and suspends the
erase operation.
The system can monitor DQ3 to determine if the sector erase timer has timed out (See the section on DQ3:
Sector Erase Timer.). The time-out begins from the rising edge of the final WE# pulse in the command
sequence.
After an erase-suspended program operation is complete, the device returns to the erase-suspend-read
mode. The system can determine the status of the
program operation using the DQ7 or DQ6 status bits,
just as in the standard word program operation.
June 14, 2005
After the erase operation has been suspended, the
device enters the erase-suspend-read mode. The system can read data from or program data to any sector
not selected for erasure. (The device “erase suspends” all sectors selected for erasure.) Reading at
any address within erase-suspended sectors produces status information on DQ7–DQ0. The system
can use DQ7, or DQ6 and DQ2 together, to determine
if a sector is actively erasing or is erase-suspended.
Refer to the Write Operation Status section for information on these status bits.
Am29LV641G
30
A D V A N C E
I N F O R M A T I O N
Refer to the Write Operation Status section for more
information.
In the erase-suspend-read mode, the system can also
issue the autoselect command sequence. Refer to the
Autoselect Mode and Autoselect Command Sequence
sections for details.
START
Write Erase
Command Sequence
(Notes 1, 2)
To resume the sector erase operation, the system
must write the Erase Resume command. The address
of the erase-suspended sector is required when writing this command. Further writes of the Resume command are ignored. Another Erase Suspend command
can be written after the chip has resumed erasing.
Data Poll to Erasing
Bank from System
No
Embedded
Erase
algorithm
in progress
Data = FFh?
Yes
Erasure Completed
Notes:
1. See Table 10 for erase command sequence.
2. See the section on DQ3 for information on the sector
erase timer.
Figure 5.
31
Am29LV641G
Erase Operation
June 14, 2005
A D V A N C E
I N F O R M A T I O N
Command Definitions
Table 10.
Read (Note 6)
Autoselect (Note 8)
Reset (Note 7)
Bus Cycles (Notes 2–5)
Cycles
Command
Sequence
(Note 1)
Command Definitions
Addr
Data
1
RA
RD
First
Second
Third
Fourth
Fifth
Addr
Data
Addr
Data
Addr
Data
1
XXX
F0
Manufacturer ID
4
555
AA
2AA
55
555
90
X00
0001
Device ID
4
555
AA
2AA
55
555
90
X01
22E7
SecSi™ Sector Factory
Protect (Note 9)
4
555
AA
2AA
55
555
90
X03
(see
Note 9)
Sector Group Protect Verify
(Note 10)
4
555
AA
2AA
55
555
90
(SA)X02
XX00/
XX01
Sixth
Addr
Data
Addr
Data
X0E
220F
X0F
(Note
16)
Enter SecSi Sector Region
3
555
AA
2AA
55
555
88
Exit SecSi Sector Region
4
555
AA
2AA
55
555
90
XXX
00
Program
4
555
AA
2AA
55
555
A0
PA
PD
Unlock Bypass
555
AA
2AA
55
555
20
XXX
A0
PA
PD
Unlock Bypass Reset (Note 12)
3
2
2
XXX
90
XXX
00
Chip Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
555
10
Sector Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
SA
30
Unlock Bypass Program (Note 11)
Erase Suspend (Note 13)
1
BA
B0
Erase Resume (Note 14)
1
BA
30
CFI Query (Note 15)
1
55
98
Legend:
X = Don’t care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses
latch on the falling edge of the WE# or CE# pulse, whichever happens
later.
Notes:
1. See Table 1 for description of bus operations.
PD = Data to be programmed at location PA. Data latches on the rising
edge of WE# or CE# pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or
erased. Address bits A21–A15 uniquely select any sector.
9.
2.
All values are in hexadecimal.
3.
Except for the read cycle and the fourth cycle of the autoselect
command sequence, all bus cycles are write cycles.
4.
Data bits DQ15–DQ8 are don’t care in command sequences,
except for RD and PD.
5.
Unless otherwise noted, address bits A21–A15 are don’t cares.
6.
No unlock or command cycles required when device is in read
mode.
7.
The Reset command is required to return to the read mode (or to
the erase-suspend-read mode if previously in Erase Suspend)
when the device is in the autoselect mode, or if DQ5 goes high
(while the device is providing status information).
8.
The fourth cycle of the autoselect command sequence is a read
cycle. Data bits DQ15–DQ8 are don’t care. See the Autoselect
Command Sequence section for more information.
If WP# protects the highest address sector, the data is 98h for
factory locked and 18h for not factory locked. If WP# protects the
lowest address sector, the data is 88h for factory locked and 08h
for not factor locked.
10. The data is 00h for an unprotected sector group and 01h for a
protected sector group.
11. The Unlock Bypass command is required prior to the Unlock
Bypass Program command.
12. The Unlock Bypass Reset command is required to return to the
read mode when the device is in the unlock bypass mode.
13. The system may read and program in non-erasing sectors, or
enter the autoselect mode, when in the Erase Suspend mode.
The Erase Suspend command is valid only during a sector erase
operation.
14. The Erase Resume command is valid only during the Erase
Suspend mode.
15. Command is valid when device is ready to read array data or
when device is in autoselect mode.
16. Bottom boot = 2200 and top boot = 2201.
June 14, 2005
Am29LV641G
32
A D V A N C E
I N F O R M A T I O N
WRITE OPERATION STATUS
The device provides several bits to determine the status of
a program or erase operation: DQ2, DQ3, DQ5, DQ6, and
DQ7. Table 11 and the following subsections describe the
function of these bits. DQ7 and DQ6 each offer a method for
determining whether a program or erase operation is complete or in progress.
in the AC Characteristics section shows the Data#
Polling timing diagram.
START
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system
whether an Embedded Program or Erase algorithm is in
progress or completed, or whether the device is in Erase
Suspend. Data# Polling is valid after the rising edge of the
final WE# pulse in the command sequence.
Read DQ7–DQ0
Addr = VA
During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to
DQ7. This DQ7 status also applies to programming during
Erase Suspend. When the Embedded Program algorithm is
complete, the device outputs the datum programmed to
DQ7. The system must provide the program address to
read valid status information on DQ7. If a program address
falls within a protected sector, Data# Polling on DQ7 is active for approximately 1 µs, then the device returns to the
read mode.
DQ7 = Data?
No
No
Just prior to the completion of an Embedded Program
or Erase operation, DQ7 may change asynchronously
with DQ0–DQ6 while Output Enable (OE#) is asserted
low. That is, the device may change from providing
status information to valid data on DQ7. Depending on
when the system samples the DQ7 output, it may read
the status or valid data. Even if the device has completed the program or erase operation and DQ7 has
valid data, the data outputs on DQ0–DQ6 may be still
invalid. Valid data on DQ0–DQ7 will appear on successive read cycles.
Table 11 shows the outputs for Data# Polling on DQ7.
Figure 6 shows the Data# Polling algorithm. Figure 19
33
DQ5 = 1?
Yes
During the Embedded Erase algorithm, Data# Polling
produces a “0” on DQ7. When the Embedded Erase
algorithm is complete, or if the device enters the Erase
Suspend mode, Data# Polling produces a “1” on DQ7.
The system must provide an address within any of the
sectors selected for erasure to read valid status information on DQ7.
After an erase command sequence is written, if all
sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately 100 µs, then
the device returns to the read mode. If not all selected
sectors are protected, the Embedded Erase algorithm
erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address within a protected
sector, the status may not be valid.
Yes
Read DQ7–DQ0
Addr = VA
DQ7 = Data?
Yes
No
FAIL
PASS
Notes:
1. VA = Valid address for programming. During a sector
erase operation, a valid address is any sector address
within the sector being erased. During chip erase, a
valid address is any non-protected sector address.
2. DQ7 should be rechecked even if DQ5 = “1” because
DQ7 may change simultaneously with DQ5.
Figure 6. Data# Polling Algorithm
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded
Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase
Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final
WE# pulse in the command sequence (prior to the
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
program or erase operation), and during the sector
erase time-out.
START
During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause
DQ6 to toggle. The system may use either OE# or
CE# to control the read cycles. When the operation is
complete, DQ6 stops toggling.
Read DQ7–DQ0
After an erase command sequence is written, if all sectors
selected for erasing are protected, DQ6 toggles for approximately 100 µs, then returns to reading array data. If not all
selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected.
Read DQ7–DQ0
Toggle Bit
= Toggle?
The system can use DQ6 and DQ2 together to determine
whether a sector is actively erasing or is erase-suspended.
When the device is actively erasing (that is, the Embedded
Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling.
However, the system must also use DQ2 to determine
which sectors are erasing or erase-suspended. Alternatively, the system can use DQ7 (see the subsection on
DQ7: Data# Polling).
No
Yes
No
DQ5 = 1?
Yes
If a program address falls within a protected sector,
DQ6 toggles for approximately 1 μs after the program
command sequence is written, then returns to reading
array data.
Read DQ7–DQ0
Twice
DQ6 also toggles during the erase-suspend-program
mode, and stops toggling once the Embedded Program algorithm is complete.
Toggle Bit
= Toggle?
Table 11 shows the outputs for Toggle Bit I on DQ6.
Figure 7 shows the toggle bit algorithm. Figure 20 in
the “AC Characteristics” section shows the toggle bit
timing diagrams. Figure 21 shows the differences between DQ2 and DQ6 in graphical form. See also the
subsection on DQ2: Toggle Bit II.
No
Yes
Program/Erase
Operation Not
Complete, Write
Reset Command
Figure 7.
Program/Erase
Operation Complete
Toggle Bit Algorithm
Note: The system should recheck the toggle bit even if DQ5
= “1” because the toggle bit may stop toggling as DQ5
changes to “1.” See the subsections on DQ6 and DQ2 for
more information.
June 14, 2005
Am29LV641G
34
A D V A N C E
I N F O R M A T I O N
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing
(that is, the Embedded Erase algorithm is in progress),
or whether that sector is erase-suspended. Toggle Bit
II is valid after the rising edge of the final WE# pulse in
the command sequence.
the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform
other system tasks. In this case, the system must start
at the beginning of the algorithm when it returns to determine the status of the operation (top of Figure 7).
DQ5: Exceeded Timing Limits
DQ2 toggles when the system reads at addresses
within those sectors that have been selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot distinguish
whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the
device is actively erasing, or is in Erase Suspend, but
cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and
mode information. Refer to Table 11 to compare outputs for DQ2 and DQ6.
DQ5 indicates whether the program or erase time has
exceeded a specified internal pulse count limit. Under these
conditions DQ5 produces a “1,” indicating that the program
or erase cycle was not successfully completed.
Figure 7 shows the toggle bit algorithm in flowchart
form, and the section “DQ2: Toggle Bit II” explains the
algorithm. See also the DQ6: Toggle Bit I subsection.
Figure 20 shows the toggle bit timing diagram. Figure
21 shows the differences between DQ2 and DQ6 in
graphical form.
Under both these conditions, the system must write
the reset command to return to the read mode (or to
the erase-suspend-read mode if the device was previously in the erase-suspend-program mode).
Reading Toggle Bits DQ6/DQ2
Refer to Figure 7 for the following discussion. Whenever the system initially begins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to
determine whether a toggle bit is toggling. Typically,
the system would note and store the value of the toggle bit after the first read. After the second read, the
system would compare the new value of the toggle bit
with the first. If the toggle bit is not toggling, the device
has completed the program or erase operation. The
system can read array data on DQ7–DQ0 on the following read cycle.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high
(see the section on DQ5). If it is, the system should
then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling
just as DQ5 went high. If the toggle bit is no longer
toggling, the device has successfully completed the
program or erase operation. If it is still toggling, the device did not completed the operation successfully, and
the system must write the reset command to return to
reading array data.
The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has
not gone high. The system may continue to monitor
35
The device may output a “1” on DQ5 if the system tries
to program a “1” to a location that was previously programmed to “0.” Only an erase operation can
change a “0” back to a “1.” Under this condition, the
device halts the operation, and when the timing limit
has been exceeded, DQ5 produces a “1.”
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not
erasure has begun. (The sector erase timer does not
apply to the chip erase command.) If additional
sectors are selected for erasure, the entire time-out
also applies after each additional sector erase command. When the time-out period is complete, DQ3
switches from a “0” to a “1.” If the time between additional sector erase commands from the system can be
assumed to be less than 50 µs, the system need not
monitor DQ3. See also the Sector Erase Command
Sequence section.
After the sector erase command is written, the system
should read the status of DQ7 (Data# Polling) or DQ6
(Toggle Bit I) to ensure that the device has accepted
the command sequence, and then read DQ3. If DQ3 is
“1,” the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored
until the erase operation is complete. If DQ3 is “0,” the
device will accept additional sector erase commands.
To ensure the command has been accepted, the system software should check the status of DQ3 prior to
and following each subsequent sector erase command. If DQ3 is high on the second status check, the
last command might not have been accepted.
Table 11 shows the status of DQ3 relative to the other
status bits.
Am29LV641G
June 14, 2005
A D V A N C E
Table 11.
Standard
Mode
Erase
Suspend
Mode
I N F O R M A T I O N
Write Operation Status
Status
Embedded Program Algorithm
Embedded Erase Algorithm
Erase
Erase-Suspend-Re Suspended Sector
ad
Non-Erase Suspended
Sector
Erase-Suspend-Program
DQ7
(Note 2)
DQ7#
0
DQ6
Toggle
Toggle
DQ5
(Note 1)
0
0
DQ3
N/A
1
DQ2
(Note 2)
No toggle
Toggle
1
No toggle
0
N/A
Toggle
Data
Data
Data
Data
Data
DQ7#
Toggle
0
N/A
N/A
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits.
Refer to the section on DQ5 for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
June 14, 2005
Am29LV641G
36
A D V A N C E
I N F O R M A T I O N
ABSOLUTE MAXIMUM RATINGS
Storage Temperature
Plastic Packages . . . . . . . . . . . . . . . –65°C to +150°C
Ambient Temperature
with Power Applied. . . . . . . . . . . . . . –65°C to +125°C
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . .–0.5 V to +4.0 V
20 ns
20 ns
+0.8 V
–0.5 V
–2.0 V
VIO . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to +5.5 V
20 ns
A9, OE#, ACC, and RESET#
(Note 2) . . . . . . . . . . . . . . . . . . . .–0.5 V to +12.5 V
Figure 8. Maximum Negative
Overshoot Waveform
All other pins (Note 1) . . . . . . –0.5 V to VCC +0.5 V
Output Short Circuit Current (Note 3) . . . . . . 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is –0.5 V.
During voltage transitions, input or I/O pins may
overshoot V SS to –2.0 V for periods of up to 20 ns.
Maximum DC voltage on input or I/O pins is VCC +0.5 V.
See Figure 8. During voltage transitions, input or I/O pins
may overshoot to VCC +2.0 V for periods up to 20 ns. See
Figure 9.
20 ns
VCC
+2.0 V
VCC
+0.5 V
2.0 V
2. Minimum DC input voltage on pins A9, OE#, ACC, and
RESET# is –0.5 V. During voltage transitions, A9, OE#,
ACC, and RESET# may overshoot V SS to –2.0 V for
periods of up to 20 ns. See Figure 8. Maximum DC input
voltage on pin A9, OE#, ACC, and RESET# is +12.5 V
which may overshoot to +14.0 V for periods up to 20 ns.
20 ns
20 ns
Figure 9. Maximum Positive
Overshoot Waveform
3. No more than one output may be shorted to ground at a
time. Duration of the short circuit should not be greater
than one second.
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This
is a stress rating only; functional operation of the device at
these or any other conditions above those indicated in the
operational sections of this data sheet is not implied.
Exposure of the device to absolute maximum rating
conditions for extended periods may affect device reliability.
OPERATING RANGES
Industrial (I) Devices
Ambient Temperature (TA) . . . . . . . . . –40°C to +85°C
VCC Supply Voltages
VCC for all devices . . . . . . . . . . . . . . . . . 2.7 V to 3.6 V
Operating ranges define those limits between which the
functionality of the device is guaranteed.
37
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
DC CHARACTERISTICS
CMOS Compatible
Parameter
Symbol
Parameter Description
Test Conditions
Min
ILI
Input Load Current (Note 1)
VIN = VSS to VCC,
VCC = VCC max
ILIT
A9, ACC Input Load Current
VCC = VCC max; A9 = 12.5 V
ILO
Output Leakage Current
VOUT = VSS to VCC,
VCC = VCC max
ICC1
VCC Active Read Current
(Notes 2, 3)
CE# = VIL, OE# = VIH
Typ
Max
Unit
±1.0
µA
35
µA
±1.0
µA
5 MHz
9
16
1 MHz
2
4
ICC2
VCC Active Write Current (Notes 3, 4) CE# = VIL, OE# = VIH, WE# = VIL
15
26
mA
ICC3
VCC Standby Current (Note 3)
CE#, RESET# = VCC ± 0.3 V,
WP# = VIH
0.2
5
µA
ICC4
VCC Reset Current (Note 3)
RESET# = VSS ± 0.3 V, WP# = VIH
0.2
5
µA
ICC5
Automatic Sleep Mode (Notes 3, 5)
VIH = VCC ± 0.3 V;
VIL = VSS ± 0.3 V, WP# = VIH
0.2
5
µA
VIL
Input Low Voltage (Note 6)
–0.5
0.8
V
VIH
Input High Voltage (Note 6)
0.7 x VCC
VCC + 0.3
V
VHH
Voltage for ACC Program
Acceleration
VCC = 3.0 V ± 10%
11.5
12.5
V
VID
Voltage for Autoselect and Temporary
VCC = 3.0 V ± 10%
Sector Unprotect
8.5
12.5
V
VOL
Output Low Voltage
0.45
V
VOH1
Output High Voltage (Note 7)
VOH2
VLKO
IOL = 4.0 mA, VCC = VCC min
mA
IOH = –2.0 mA, VCC = VCC min
0.85 x VIO
V
IOH = –100 µA, VCC = VCC min
VIO–0.4
V
Low VCC Lock-Out Voltage (Note 7)
2.3
2.5
V
Notes:
1. On the WP# pin only, the maximum input load current when WP# = VIL is ± 5.0 µA.
2.
3.
4.
5.
The ICC current listed is typically less than 2 mA/MHz, with OE# at VIH.
Maximum ICC specifications are tested with VCC = VCCmax.
ICC active while Embedded Erase or Embedded Program is in progress.
Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30 ns. Typical sleep mode current is
200 nA.
6. If VIO < VCC, maximum VIL for CE# is 0.3 x VIO. If VIO < VCC, minimum VIH for CE# is 0.3 x VIO.
7. Not 100% tested.
June 14, 2005
Am29LV641G
38
A D V A N C E
I N F O R M A T I O N
DC CHARACTERISTICS
Zero-Power Flash
Supply Current in mA
25
20
15
10
5
0
0
500
1000
1500
Note: Addresses are switching at 1 MHz
Figure 10.
2000
2500
3000
3500
4000
Time in ns
ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents)
12
3.6 V
10
Supply Current in mA
8
2.7 V
6
4
2
0
1
2
3
4
5
Frequency in MHz
Note: T = 25 °C
Figure 11.
39
Typical ICC1 vs. Frequency
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
TEST CONDITIONS
Table 12.
3.3 V
Test Condition
2.7 kΩ
Device
Under
Test
CL
Test Specifications
6.2 kΩ
55R
Figure 12.
Test Setup
Unit
Output Load
1 TTL gate
Output Load Capacitance, CL
(including jig capacitance)
30
pF
Input Rise and Fall Times
5
ns
0.0–3.0
V
Input timing measurement
reference levels (See Note)
1.5
V
Output timing measurement
reference levels
0.5 VIO
V
Input Pulse Levels
Note: Diodes are IN3064 or equivalent
70R
Note: If VIO < VCC, the reference level is 0.5 VIO.
KEY TO SWITCHING WAVEFORMS
WAVEFORM
INPUTS
OUTPUTS
Steady
Changing from H to L
Changing from L to H
3.0 V
Input
Don’t Care, Any Change Permitted
Changing, State Unknown
Does Not Apply
Center Line is High Impedance State (High Z)
1.5 V
Measurement Level
0.5 VIO V
Output
0.0 V
Note: If VIO < VCC, the input measurement reference level is 0.5 VIO.
Figure 13. Input Waveforms and
Measurement Levels
June 14, 2005
Am29LV641G
40
A D V A N C E
I N F O R M A T I O N
AC CHARACTERISTICS
Read-Only Operations
Parameter
Speed Options
JEDEC
Std.
Description
Test Setup
55R
70
Unit
tAVAV
tRC
Read Cycle Time (Note 1)
Min
55
70
ns
tAVQV
tACC
Address to Output Delay
CE#, OE# = VIL
Max
55
70
ns
tELQV
tCE
Chip Enable to Output Delay
OE# = VIL
Max
55
70
ns
tGLQV
tOE
Output Enable to Output Delay
Max
30
ns
tEHQZ
tDF
Chip Enable to Output High Z (Note 1)
Max
16
ns
tGHQZ
tDF
Output Enable to Output High Z (Note 1)
Max
16
ns
tAXQX
tOH
Output Hold Time From Addresses, CE# or
OE#, Whichever Occurs First
Min
0
ns
Read
Min
0
ns
tOEH
Output Enable Hold
Time (Note 1)
Toggle and
Data# Polling
Min
10
ns
Notes:
1. Not 100% tested.
2. See Figure 12 and Table 12 for test specifications.
tRC
Addresses Stable
Addresses
tACC
CE#
tRH
tRH
tDF
tOE
OE#
tOEH
WE#
tCE
tOH
HIGH Z
HIGH Z
Output Valid
Outputs
RESET#
Figure 14.
41
Read Operation Timings
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
AC CHARACTERISTICS
Hardware Reset (RESET#)
Parameter
JEDEC
Std
Description
All Speed Options
Unit
tReady
RESET# Pin Low (During Embedded Algorithms)
to Read Mode (See Note)
Max
20
μs
tReady
RESET# Pin Low (NOT During Embedded
Algorithms) to Read Mode (See Note)
Max
500
ns
tRP
RESET# Pulse Width
Min
500
ns
tRH
Reset High Time Before Read (See Note)
Min
50
ns
tRPD
RESET# Low to Standby Mode
Min
20
μs
Note: Not 100% tested.
CE#, OE#
tRH
RESET#
tRP
tReady
Reset Timings NOT during Embedded Algorithms
Reset Timings during Embedded Algorithms
tReady
CE#, OE#
RESET#
tRP
Figure 15.
June 14, 2005
Reset Timings
Am29LV641G
42
A D V A N C E
I N F O R M A T I O N
AC CHARACTERISTICS
Erase and Program Operations
Parameter
Speed Options
JEDEC
Std.
Description
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
0
ns
tASO
Address Setup Time to OE# low during toggle bit polling
Min
15
ns
tAH
Address Hold Time
Min
40
ns
tAHT
Address Hold Time From CE# or OE# high
during toggle bit polling
Min
0
ns
tDVWH
tDS
Data Setup Time
Min
40
ns
tWHDX
tDH
Data Hold Time
Min
0
ns
tOEPH
Output Enable High during toggle bit polling
Min
20
ns
tGHWL
tGHWL
Read Recovery Time Before Write
(OE# High to WE# Low)
Min
0
ns
tELWL
tCS
CE# Setup Time
Min
0
ns
tWHEH
tCH
CE# Hold Time
Min
0
ns
tWLWH
tWP
Write Pulse Width
Min
30
ns
tWHDL
tWPH
Write Pulse Width High
Min
25
ns
tWHWH1
tWHWH1
Word Programming Operation (Note 2)
Typ
7
µs
tWHWH1
tWHWH1
Accelerated Word Programming Operation (Note 2)
Typ
4
µs
tWHWH2
tWHWH2
Sector Erase Operation (Note 2)
Typ
0.6
sec
tVHH
VHH Rise and Fall Time (Note 1)
Min
250
ns
tVCS
VCC Setup Time (Note 1)
Min
50
µs
tWLAX
55R
70
Unit
55
70
ns
Notes:
1. Not 100% tested.
2. See the “Erase And Programming Performance” section for more information.
43
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
AC CHARACTERISTICS
Program Command Sequence (last two cycles)
tAS
tWC
Addresses
Read Status Data (last two cycles)
555h
PA
PA
PA
tAH
CE#
tCH
OE#
tWHWH1
tWP
WE#
tWPH
tCS
tDS
tDH
PD
A0h
Data
Status
DOUT
VCC
tVCS
Notes:
1. PA = program address, PD = program data, DOUT is the true data at the program address.
Illustration shows device in word mode.
Figure 16.
Program Operation Timings
VHH
ACC
VIL or VIH
VIL or VIH
tVHH
Figure 17.
June 14, 2005
tVHH
Accelerated Program Timing Diagram
Am29LV641G
44
A D V A N C E
I N F O R M A T I O N
AC CHARACTERISTICS
Erase Command Sequence (last two cycles)
tAS
tWC
2AAh
Addresses
Read Status Data
VA
SA
VA
555h for chip erase
tAH
CE#
tCH
OE#
tWP
WE#
tWPH
tCS
tWHWH2
tDS
tDH
Data
55h
30h
In
Progress
Complete
10 for Chip Erase
tVCS
VCC
Notes:
1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status”.
2. These waveforms are for the word mode.
Figure 18.
45
Chip/Sector Erase Operation Timings
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
AC CHARACTERISTICS
tRC
Addresses
VA
VA
VA
tACC
tCE
CE#
tCH
tOE
OE#
tOEH
tDF
WE#
tOH
High Z
DQ7
Complement
Complement
DQ6–DQ0
Status Data
Status Data
True
Valid Data
High Z
True
Valid Data
Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data
read cycle.
Figure 19. Data# Polling Timings
(During Embedded Algorithms)
June 14, 2005
Am29LV641G
46
A D V A N C E
I N F O R M A T I O N
AC CHARACTERISTICS
tAHT
tAS
Addresses
tAHT
tASO
CE#
tCEPH
tOEH
WE#
tOEPH
OE#
tDH
DQ6/DQ2
tOE
Valid
Status
Valid
Status
Valid
Status
(first read)
(second read)
(stops toggling)
Valid Data
Valid Data
Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status
read cycle, and array data read cycle
Figure 20. Toggle Bit Timings
(During Embedded Algorithms)
Enter
Embedded
Erasing
WE#
Erase
Suspend
Erase
Enter Erase
Suspend Program
Erase
Suspend
Program
Erase Suspend
Read
Erase
Resume
Erase Suspend
Read
Erase
Erase
Complete
DQ6
DQ2
Note: DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle
DQ2 and DQ6.
Figure 21.
47
DQ2 vs. DQ6
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
AC CHARACTERISTICS
Temporary Sector Unprotect
Parameter
JEDEC
Std
Description
tVIDR
VID Rise and Fall Time (See Note)
tRSP
RESET# Setup Time for Temporary Sector
Unprotect
All Speed Options
Unit
Min
500
ns
Min
4
µs
Note: Not 100% tested.
VID
RESET#
VID
VSS, VIL,
or VIH
VSS, VIL,
or VIH
tVIDR
tVIDR
Program or Erase Command Sequence
CE#
WE#
tRSP
Figure 22.
June 14, 2005
Temporary Sector Group Unprotect Timing Diagram
Am29LV641G
48
A D V A N C E
I N F O R M A T I O N
AC CHARACTERISTICS
VID
VIH
RESET#
SA, A6,
A1, A0
Valid*
Valid*
Sector Group Protect or Unprotect
Data
60h
60h
Valid*
Verify
40h
Status
Sector Group Protect: 150 µs,
Sector Group Unprotect: 15 ms
1 µs
CE#
WE#
OE#
* For sector group protect, A6 = 0, A1 = 1, A0 = 0. For sector group unprotect, A6 = 1, A1 = 1, A0 = 0.
Figure 23.
49
Sector Group Protect and Unprotect Timing Diagram
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
AC CHARACTERISTICS
Alternate CE# Controlled Erase and Program Operations
Parameter
Speed Options
JEDEC
Std
Description
55R
70
Unit
tAVAV
tWC
Write Cycle Time (Note 1)
Min
55
70
ns
tAVWL
tAS
Address Setup Time
Min
0
ns
tELAX
tAH
Address Hold Time
Min
40
ns
tDVEH
tDS
Data Setup Time
Min
40
ns
tEHDX
tDH
Data Hold Time
Min
0
ns
tGHEL
tGHEL
Read Recovery Time Before Write
(OE# High to WE# Low)
Min
0
ns
tWLEL
tWS
WE# Setup Time
Min
0
ns
tEHWH
tWH
WE# Hold Time
Min
0
ns
tELEH
tCP
CE# Pulse Width
Min
45
ns
tEHEL
tCPH
CE# Pulse Width High
Min
30
ns
tWHWH1
tWHWH1
Word Programming Operation (Note 2)
Typ
7
µs
tWHWH1
tWHWH1
Accelerated Word Programming Operation (Note 2)
Typ
4
µs
tWHWH2
tWHWH2
Sector Erase Operation (Note 2)
Typ
0.6
sec
Notes:
1. Not 100% tested.
2. See the “Erase And Programming Performance” section for more information.
June 14, 2005
Am29LV641G
50
A D V A N C E
I N F O R M A T I O N
AC CHARACTERISTICS
555 for program
2AA for erase
PA for program
SA for sector erase
555 for chip erase
Data# Polling
Addresses
PA
tWC
tAS
tAH
tWH
WE#
tGHEL
OE#
tWHWH1 or 2
tCP
CE#
tWS
tCPH
tBUSY
tDS
tDH
DQ7#
Data
tRH
A0 for program
55 for erase
DOUT
PD for program
30 for sector erase
10 for chip erase
RESET#
RY/BY#
Notes:
1. Figure indicates last two bus cycles of a program or erase operation.
2. PA = program address, SA = sector address, PD = program data.
3. DQ7# is the complement of the data written to the device. DOUT is the data written to the device.
4. Waveforms are for the word mode.
Figure 24.
51
Alternate CE# Controlled Write (Erase/Program) Operation Timings
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
ERASE AND PROGRAMMING PERFORMANCE
Parameter
Typ (Note 1)
Max (Note 2)
Unit
Comments
Sector Erase Time
0.6
4
sec
Chip Erase Time
50
Excludes 00h programming
prior to erasure (Note 4)
Word Program Time
7
210
µs
Accelerated Word Program Time
4
120
µs
Chip Program Time (Note 3)
18
54
sec
sec
Excludes system level
overhead (Note 5)
Notes:
1. Typical program and erase times assume the following conditions: 25°C, 3.0 V VCC, 1,000,000 cycles. Additionally, programming typicals
assume checkerboard pattern.
2. Under worst case conditions of 90°C, VCC = 3.0 V, 1,000,000 cycles.
3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most words program faster than
the maximum program times listed.
4. In the pre-programming step of the Embedded Erase algorithm, all bits are programmed to 00h before erasure.
5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Table 10 for further
information on command definitions.
6. The device has a minimum erase and program cycle endurance of 1,000,000 cycles.
LATCHUP CHARACTERISTICS
Description
Min
Max
Input voltage with respect to VSS on all pins except I/O pins
(including A9, OE#, and RESET#)
–1.0 V
12.5 V
Input voltage with respect to VSS on all I/O pins
–1.0 V
VCC + 1.0 V
–100 mA
+100 mA
VCC Current
Note: Includes all pins except VCC. Test conditions: VCC = 3.0 V, one pin at a time.
TSOP & FBGA PIN CAPACITANCE
Parameter Symbol
Parameter Description
CIN
Input Capacitance
COUT
Output Capacitance
CIN2
Control Pin Capacitance
Test Setup
VIN = 0
VOUT = 0
VIN = 0
Typ
Max
Unit
TSOP
6
7.5
Fine-pitch
BGA
4.2
5.0
TSOP
8.5
12
Fine-pitch
BGA
5.4
6.5
TSOP
7.5
9
Fine-pitch
BGA
3.9
4.7
Notes:
1. Sampled, not 100% tested.
2. Test conditions TA = 25°C, f = 1.0 MHz.
DATA RETENTION
Parameter Description
Test Conditions
Min
Unit
150°C
10
Years
125°C
20
Years
Minimum Pattern Data Retention Time
June 14, 2005
Am29LV641G
52
A D V A N C E
I N F O R M A T I O N
PHYSICAL DIMENSIONS
FBE063—63-Ball Fine-Pitch Ball Grid Array (FBGA) 11 x 12 mm package
Dwg rev AF; 10/99
53
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
PHYSICAL DIMENSIONS
LAA064–64-Ball Fortified Ball Grid Array (Fortified BGA) 13 x 11 mm package
54
Am29LV641G
June 14, 2005
A D V A N C E
I N F O R M A T I O N
PHYSICAL DIMENSIONS
TS 048—48-Pin Standard TSOP
)
Dwg rev AA; 10/99
Note: For reference only. BSC is an ANSI standard for Basic Space Centering.
June 14, 2005
Am29LV641G
55
A D V A N C E
I N F O R M A T I O N
REVISION SUMMARY
Revision A (August 9, 2002)
Customer Lockable: SecSi Sector NOT
Programmed or Protected at the factory.
Initial Release.
Revision A+1 (August 28, 2002)
Added second bullet, SecSi sector-protect verify text
and figure 3.
Ordering Information
Common Flash Memory Interface (CFI)
Corrected order numbers and package markings.
Added Marking Convention explanation about Enhanced-VIO markings.
Revision A+2 (October 18, 2002)
Changed wording in last sentence of third paragraph
from, “...the autoselect mode.” to “...reading array
data.”
Changed CFI website address.
Command Definitions
Global
Connection Diagram
Changed wording in last sentence of first paragraph
from, “...resets the device to reading array data.” to
...”may place the device to an unknown state. A reset
command is then required to return the device to reading array data.”
Removed the 56–pin SSOP package diagram.
TSOP Pin Capacitance
Special Package Handling Instructions
Added fine-pitch BGA capacitance.
Modified wording.
Revision A+3 (June 14, 2005)
Ordering Information
Cover Page / Title Page
Changed the VIO for 55R to equal 3.0 V–3.6 V and
added 55 ns to Valid Combinations table.
Added Spansion EOL cover page and EOL disclaimer
to AMD title page.
Added 55R speed grade and removed 90 and 100
speed grade throughout datasheet.
Trademarks
Copyright © 2001 Advanced Micro Devices, Inc. All rights reserved.
AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc.
ExpressFlash is a trademark of Advanced Micro Devices, Inc.
Product names used in this publication are for identification purposes only and may be trademarks of their respective companies.
56
Am29LV641G
June 14, 2005