AP7340 150mA HIGH PSRR LOW NOISE LDO WITH ENABLE Description Pin Assignments The AP7340 is low dropout regulator with high output voltage accuracy, low RDSON, high PSRR, low output noise and low quiescent current. This regulator is based on a CMOS process. The AP7340 includes a voltage reference, error amplifier, current limit circuit and an enable input to turn it on and off. With the integrated resistor network fixed output voltage versions can be delivered. With its low power consumption and line and load transient response the AP7340 is well suited for low power handheld communication equipment. The AP7340 is packaged in a X2-DFN1010-4 package and allows for smallest footprint and dense PCB layout. PIN1 – VOUT, PIN2 – GND, PIN3 – EN, PIN4 – VIN Features ● Low VIN and wide VIN range: 1.7V to 5.25V ● Guarantee Output Current,150mA ● VOUT accuracy ±1% ● Ripple Rejection 75dB at 1kHz ● Low output noise, 60uVrms from 10Hz to 100kHz ● Quiescent current as low as 35µA ● VOUT fixed 1.2V to 3.3V ● Totally Lead-Free & and Fully RoHS Compliant (Note 1) ● Halogen and Antimony Free, Green Device (Note 2) Notes: Applications Smart phone/PAD RF supply Cameras Portable Video Portable Media player Wireless adapter Wireless communication 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant. 2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and <1000ppm antimony compounds. Typical Applications Circuit Figure 1 Typical Application Circuit AP7340 Document number: DS35282 Rev. 2 - 2 1 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 Pin Descriptions Pin Name PIN No X2-DFN1010-4 VOUT 1 Power Output Pin GND 2 EN 3 Ground Enable pin. This pin should be driven either high or low and must not be floating. Driving this pin high enables the regulator, while pulling it low puts the regulator into shutdown mode VIN 4 Function Power Input pin Thermal PAD In PCB layout, prefer to use large copper area to cover this pad for better thermal dissipation, then connect this area to GND or leave it open. However do not use it as GND electrode function alone. Functional Block Diagram AP7340 (Non discharge) AP7340D (with discharge) Absolute Maximum Ratings (Note 4) (@TA = +25°C, unless otherwise specified.) Symbol Parameter Ratings Unit V VIN Input Voltage 6.0 VCE Input Voltage EN 6.0 V VOUT Output Voltage -0.3 to VIN +0.3 V IOUT Output Current 300 mA 400 mW PD Power Dissipation TA Operating Temperature -40 to +85 °C Storage Temperature -55 to +125 °C TSTG Note: 4. a). Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. b). Ratings apply to ambient temperature at 25°C . The JEDEC High-K board design used to derive this data was a 2 inch x 2 inch multilayer board with 1-ounce internal power and ground planes and 2-ounce copper traces on the top and bottom of the board. Recommended Operating Conditions (@TA = +25°C, unless otherwise specified.) Symbol Parameter VIN Input Voltage IOUT Output Current TA Operating Ambient Temperature AP7340 Document number: DS35282 Rev. 2 - 2 Min Max Unit 1.7 5.25 V 0 150 mA -40 +85 °C 2 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 Electrical Characteristics (VEN = VIN = VOUT +1.0V, CIN = COUT 0.47µF, IOUT = 1.0mA @TA = +25°C, unless otherwise specified.) Parameter Input Voltage Output Voltage Accuracy (Note 11) Conditions Min TA = -40°C to +85°C VIN = (VOUT – Nom +1.0V) to 5.25V, IOUT = 1mA to 150mA TA = +25°C TA = -40°C to +85°C Max Units 1.7 Typ 5.25 V -1 1 -1.5 +1.5 % Line Regulation (dVOUT/dVIN/VOUT) VIN = (VOUT – Nom +1.0V) to 5.25V, IOUT = 1.0mA 0.02 0.1 %/V Load Regulation (dVOUT/VOUT/dIOUT) VIN = VOUT - Nom +1.0V, IOUT = 1mA to 150mA 0.5 1.0 %/A Quiescent Current (Note 6) IOUT = 0mA 35 50 IOUT = 150mA 60 100 ISTANDBY VEN = 0V (Disabled) 0.01 1.0 Output Current 150 Fold-back Short Current (Note 7) VOUT short to ground PSRR (Note 8) VIN = [VOUT+1V] VDC + 0.2Vp-pAC, VOUT ≥1.8V, IOUT = 30mA Output Noise Voltage (Note 8) (Note 9) BW = 10Hz to 100kHz, IOUT = 30mA Dropout Voltage (Note 5) Output Voltage Temperature Coefficient IOUT = 150mA f = 1kHz uA mA 55 mA 75 dB 60 µVrms 1.2V ≤ VOUT < 1.5V 0.50 0.62 1.5V ≤ VOUT < 1.7V 0.38 0.47 1.7V ≤ VOUT < 2.0V 0.34 0.42 2.0V ≤ VOUT < 2.5V 0.28 0.36 2.5V ≤ VOUT < 2.8V 0.22 0.30 2.8V ≤ VOUT ≤ 3.3V 0.21 0.27 ±30 IOUT = 30mA, TA = -40°C to +85°C uA V ppm/C EN Input Low Voltage 0 0.5 V EN Input High Voltage 1.3 5.25 V -1.0 +1.0 µA EN Input Leakage VEN = 0, VIN = 5.0V or VEN = 5.0V, VIN = 0V On Resistance of N-channel for auto-discharge (Note 10) Vin = 4.0V VEN = 0V (Disabled) Notes: 30 5. Dropout voltage is the voltage difference between the input and the output at which the output voltage drops 2% below its nominal value. 6. Quiescent current is defined here is the difference in current between the input and the output. 7. Short circuit current is measured with VOUT pulled to GND. 8. This specification is guaranteed by design. 9. To make sure lowest environment noise minimizes the influence on noise measurement. 10. AP7340 has 2 options for output, Built-in discharge and non-discharge 11. Potential multiple grades based on following output voltage accuracy. AP7340 Document number: DS35282 Rev. 2 - 2 3 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 Typical Characteristics Output Noise (AP7340-33) AP7340 Document number: DS35282 Rev. 2 - 2 4 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 Typical Characteristics (cont.) AP7340 Document number: DS35282 Rev. 2 - 2 5 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 Typical Characteristics (cont.) AP7340 Document number: DS35282 Rev. 2 - 2 6 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 Typical Characteristics (cont.) AP7340 Document number: DS35282 Rev. 2 - 2 7 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 Typical Characteristics (cont.) AP7340-33 3 2.520 Output Voltage 2.500 2.480 5 3.320 Output Voltage 3.300 3.280 20 40 60 80 100 0 20 Time t (µs) VIN=3.5V tr=tf=0.5µs AP7340-33 100 Output Current 50mA 100mA 50 0 2.35 2.50 Output Current I OUT (mA) Output Voltage V OUT (V) 150 Output Voltage 2.45 80 100 VIN=4.3V tr=tf=0.5µs 150 100 Output Current 50mA 100mA 50 0 3.35 3.30 3.25 Output Voltage 3.20 20 40 60 80 100 0 20 60 80 100 Time t (µs) VIN=3.5V tr=tf=0.5µs AP7340-33 150 Output Current 1mA 150mA 0 2.70 Output Current I OUT (mA) 300 VIN=4.3V tr=tf=0.5µs 300 Output Voltage V OUT (V) Output Voltage V OUT (V) AP7340-25 40 150 Output Current 1mA 150mA 0 3.50 3.30 2.50 Output Voltage 3.10 Output Voltage 2.30 Output Current I OUT (mA) 0 Time t (µs) 2.10 60 Time t (µs) Output Voltage V OUT (V) AP7340-25 40 Output Current I OUT (mA) 0 2.40 4 Input Voltage Input Voltage V IN (V) 4 Input Voltage Input Voltage V IN (V) 5 6 Output Voltage V OUT (V) Output Voltage V OUT (V) AP7340-25 2.90 0 20 40 60 80 0 100 Time t (µs) AP7340 Document number: DS35282 Rev. 2 - 2 20 40 60 80 100 Time t (µs) 8 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 Typical Characteristics (cont.) AP7340-25 IOUT=0mA IOUT=30mA 3 3 2 2 CE Input Voltage 1 3 2 1 Output Voltage 0 40 80 120 160 0 3 2 1 Output Voltage 0 0 200 40 120 160 200 Time t (µs) Time t (µs) AP7340-25 80 AP7340-33 IOUT=150mA 3 IOUT=0mA 3 2 2 CE Input Voltage 0 3 2 1 Output Voltage 0 0 40 80 120 160 1 Output Voltage V OUT (V) Output Voltage V OUT (V) 1 CE Input Voltage V CE (V) CE Input Voltage 0 3 2 1 Output Voltage 0 200 0 40 Time t (µs) AP7340-33 80 120 AP7340-33 IOUT=30mA CE Input Voltage 2 1 Output Voltage 40 80 120 160 200 CE Input Voltage V CE (V) Output Voltage V OUT (V) 3 Output Voltage V OUT (V) 1 1 0 0 3 2 1 Output Voltage 0 0 Document number: DS35282 Rev. 2 - 2 40 80 120 160 200 Time t (µs) Time t (µs) AP7340 IOUT=150mA 3 2 2 CE Input Voltage 0 200 Time t (µs) 3 0 160 CE Input Voltage V CE (V) 0 Output Voltage V OUT (V) 0 CE Input Voltage V CE (V) Output Voltage V OUT (V) 1 CE Input Voltage V CE (V) CE Input Voltage CE Input Voltage V CE (V) AP7340-25 9 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 Typical Characteristics (cont.) AP7340-18 IOUT=0mA AP7340-18 6 IOUT=30mA 66 4 CE Input Voltage 2 Output Voltage 1 0 80 120 160 3 2 Output Voltage 1 0 200 0 40 80 AP7340-18 120 160 200 Time t (µs) Time t (µs) AP7340-33 IOUT=150mA 6 IOUT=0mA 6 4 4 CE Input Voltage CE Input Voltage 2 0 3 2 Output Voltage 1 0 0 40 80 120 160 Output Voltage V OUT (V) 4 CE Input Voltage V CE (V) Output Voltage V OUT (V) 2 4 0 3 2 Output Voltage 1 0 0 200 40 120 AP7340-33 IOUT=30mA 6 3 2 Output Voltage 0 40 80 120 160 200 CE Input Voltage V CE (V) Output Voltage V OUT (V) 0 Output Voltage V OUT (V) 2 2 4 4 0 3 2 Output Voltage 1 0 0 Document number: DS35282 Rev. 2 - 2 40 80 120 160 200 Time t (µs) Time t (µs) AP7340 IOUT=150mA 6 CE Input Voltage CE Input Voltage 0 200 4 4 1 160 Time t (µs) Time t (µs) AP7340-33 80 CE Input Voltage V CE (V) 40 0 CE Input Voltage V CE (V) 0 4 CE Input Voltage V CE (V) 3 2 Output Voltage V OUT (V) 0 CE Input Voltage V CE (V) Output Voltage V OUT (V) 4 4 CE Input Voltage 2 10 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 Application Information Output Capacitor An output capacitor (COUT) is needed to improve transient response and maintain stability. The AP7340 is stable with very small ceramic output capacitors. The ESR (equivalent series resistance) and capacitance drives the selection. If the application has large load variations, it is recommended to utilize low-ESR bulk capacitors. It is recommended to place ceramic capacitors as close as possible to the load and the ground pin and care should be taken to reduce the impedance in the layout. Input Capacitor To prevent the input voltage from dropping during load steps it is recommended to utilize an input capacitor (CIN). A minimum 0.47μF ceramic capacitor is recommended between VIN and GND pins to decouple input power supply glitch. This input capacitor must be located as close as possible to the device to assure input stability and reduce noise. For PCB layout, a wide copper trace is required for both VIN and GND pins. Enable Control The AP7340 is turned on by setting the EN pin high, and is turned off by pulling it low. If this feature is not used, the EN pin should be tied to VIN pin to keep the regulator output on at all time. To ensure proper operation, the signal source used to drive the EN pin must be able to swing above and below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section. Short Circuit Protection When VOUT pin is short-circuit to GND, short circuit protection will be triggered and clamp the output current to approximately 60mA. This feature protects the regulator from over-current and damage due to overheating. Layout Considerations For good ground loop and stability, the input and output capacitors should be located close to the input, output, and ground pins of the device. The regulator ground pin should be connected to the external circuit ground to reduce voltage drop caused by trace impedance. Ground plane is generally used to reduce trace impedance. Wide trace should be used for large current paths from VIN to VOUT, and load circuit. ESR vs. Output Current Ceramic type output capacitor is recommended for this series; however, the other output capacitors with low ESR also can be used. The relations between IOUT (Output Current) and ESR of an output capacitor are shown below. The stable region is marked as the hatched area in the graph. Measurement conditions: Frequency Band : 10Hz to 2MHz, Temperature AP7340 Document number: DS35282 Rev. 2 - 2 : -40°C to +85°C 11 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 Ordering Information Part Number Package Code Packaging AP7340-XXFS4-7 AP7340D-XXFS4-7 FS4 FS4 X2-DFN1010-4 X2-DFN1010-4 Quantity 7” Tape and Reel Part Number Suffix 5000/Tape & Reel 5000/Tape & Reel -7 -7 Marking Information X2-DFN1010-4 (Top View) XX YWX XX : Identification Code Y : Year : 0~9 W : Week : A~Z : 1~26 week; a~z : 27~52 week; z represents 52 and 53 week X : A~Z : Internal code Part Number Package Identification Code AP7340-12FS4-7 AP7340-15FS4-7 AP7340-18FS4-7 X2-DFN1010-4 X2-DFN1010-4 X2-DFN1010-4 CH CJ CK AP7340-185FS4-7 AP7340-25FS4-7 AP7340-28FS4-7 AP7340-285FS4-7 AP7340-30FS4-7 AP7340-31FS4-7 X2-DFN1010-4 X2-DFN1010-4 X2-DFN1010-4 X2-DFN1010-4 X2-DFN1010-4 X2-DFN1010-4 EV CM CN EW EX EY AP7340-32FS4-7 AP7340-33FS4-7 AP7340D-12FS4-7 AP7340D-15FS4-7 AP7340D-18FS4-7 AP7340D-185FS4-7 AP7340D-25FS4-7 X2-DFN1010-4 X2-DFN1010-4 X2-DFN1010-4 X2-DFN1010-4 X2-DFN1010-4 X2-DFN1010-4 X2-DFN1010-4 EZ CP DG DH DJ DV DK AP7340D-28FS4-7 AP7340D-285FS4-7 AP7340D-30FS4-7 AP7340D-31FS4-7 AP7340D-32FS4-7 X2-DFN1010-4 X2-DFN1010-4 X2-DFN1010-4 X2-DFN1010-4 X2-DFN1010-4 DM DW DX DY DZ AP7340 Document number: DS35282 Rev. 2 - 2 12 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 Package Outline Dimensions (All dimensions in mm.) Please see AP02002 at http://www.diodes.com/datasheets/ap02002.pdf for latest version. Package Type: X2-DFN1010-4 3 A 1 A A e n a l P g n i t a e S D e ︶ x 3 8 1 . 0 C ︵ 5 2 . 0 C 1 L E 2 L 2 D 2 E L b Z X2-DFN1010-4 Dim Min Max Typ A 0.40 0.39 A1 0.00 0.05 0.02 A3 0.13 b 0.20 0.30 0.25 D 0.95 1.05 1.00 D2 0.38 0.58 0.48 E 0.95 1.05 1.00 E2 0.38 0.58 0.48 e 0.65 L 0.20 0.30 0.25 L1 0.27 0.37 0.32 L2 0.02 0.12 0.07 Z 0.050 All Dimensions in mm Suggested Pad Layout Please see AP02001 at http://www.diodes.com/datasheets/ap02001.pdf for the latest version. Package Type: X2-DFN1010-4 2 X C 2 Y Dimensions 1 Y 3 Y 4 Y 1 X Y C X X1 X2 Y Y1 Y2 Y3 Value (in mm) 0.650 0.250 0.480 0.900 0.400 0.470 0.220 0.480 X AP7340 Document number: DS35282 Rev. 2 - 2 13 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 Tape Orientation For X2-DFN1010-4 Note: 12. The taping orientation of the other package type can be found on our website at http://www.diodes.com/datasheets/ap02007.pdf AP7340 Document number: DS35282 Rev. 2 - 2 14 of 15 www.diodes.com October 2013 © Diodes Incorporated AP7340 IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2013, Diodes Incorporated www.diodes.com AP7340 Document number: DS35282 Rev. 2 - 2 15 of 15 www.diodes.com October 2013 © Diodes Incorporated