ATMEL ATTINY15L-1PC

Features
• High-performance, Low-power AVR® 8-bit Microcontroller
• Advanced RISC Architecture
•
•
•
•
•
•
•
– 90 Powerful Instructions – Most Single Clock Cycle Execution
– 32 x 8 General Purpose Working Registers
– Fully Static Operation
Nonvolatile Program and Data Memories
– 1K Byte In-System Programmable Flash Program Memory
Endurance: 1,000 Write/Erase Cycles
– 64 Bytes EEPROM
Endurance: 100,000 Write/Erase Cycles
– Programming Lock for Flash Program Data Security
Peripheral Features
– Interrupt and Wake-up on Pin Change
– Two 8-bit Timer/Counters with Separate Prescalers
– One 150 kHz, 8-bit High-speed PWM Output
– 4-channel 10-bit ADC
One Differential Voltage Input with Optional Gain of 20x
– On-chip Analog Comparator
– Programmable Watchdog Timer with On-chip Oscillator
Special Microcontroller Features
– In-System Programmable via SPI Port
– Enhanced Power-on Reset Circuit
– Programmable Brown-out Detection Circuit
– Internal, Calibrated 1.6 MHz Tunable Oscillator
– Internal 25.6 MHz Clock Generator for Timer/Counter
– External and Internal Interrupt Sources
– Low-power Idle and Power-down Modes
Power Consumption at 1.6 MHz, 3V, 25°C
– Active: 3.0 mA
– Idle Mode: 1.0 mA
– Power-down: < 1 µA
I/O and Packages
– 8-lead PDIP and 8-lead SOIC: 6 Programmable I/O Lines
Operating Voltages
– 2.7V - 5.5V
Internal 1.6 MHz System Clock
8-bit
Microcontroller
with 1K Byte
Flash
ATtiny15L
Pin Configuration
PDIP/SOIC
(RESET/ADC0) PB5
(ADC3) PB4
(ADC2) PB3
GND
1
2
3
4
8
7
6
5
VCC
PB2 (ADC1/SCK/T0/INT0)
PB1 (AIN1/MISO/OC1A)
PB0 (AIN0/AREF/MOSI)
Rev. 1187D–12/01
1
Description
The ATtiny15L is a low-power CMOS 8-bit microcontroller based on the AVR RISC
architecture. By executing powerful instructions in a single clock cycle, the ATtiny15L
achieves throughputs approaching 1 MIPS per MHz allowing the system designer to
optimize power consumption versus processing speed.
The AVR core combines a rich instruction set with 32 general purpose working registers.
All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing
two independent registers to be accessed in one single instruction executed in one clock
cycle. The resulting architecture is more code efficient while achieving throughputs up to
ten times faster than conventional CISC microcontrollers.
The ATtiny15L provides 1K byte of Flash, 64 bytes EEPROM, six general purpose I/O
lines, 32 general purpose working registers, two 8-bit Timer/Counters, one with highspeed PWM output, internal oscillators, internal and external interrupts, programmable
Watchdog Timer, 4-channel 10-bit Analog-to-Digital Converter with one differential voltage input with optional 20x gain, and three software-selectable Power-saving modes.
The Idle mode stops the CPU while allowing the ADC, analog comparator,
Timer/Counters and interrupt system to continue functioning. The ADC Noise Reduction
mode facilitates high-accuracy ADC measurements by stopping the CPU while allowing
the ADC to continue functioning. The Power-down mode saves the register contents but
freezes the oscillators, disabling all other chip functions until the next interrupt or hardware reset. The wake-up or interrupt on pin change features enable the ATtiny15L to be
highly responsive to external events, still featuring the lowest power consumption while
in the Power-saving modes.
The device is manufactured using Atmel’s high-density, nonvolatile memory technology.
By combining a RISC 8-bit CPU with Flash on a monolithic chip, the ATtiny15L is a powerful microcontroller that provides a highly flexible and cost-efficient solution to many
embedded control applications. The peripheral features make the ATtiny15L particularly
suited for battery chargers, lighting ballasts and all kinds of intelligent sensor
applications.
The ATtiny15L AVR is supported with a full suite of program and system development
tools including macro assemblers, program debugger/simulators, In-circuit emulators
and evaluation kits.
2
ATtiny15L
1187D–12/01
ATtiny15L
Block Diagram
Figure 1. The ATtiny15L Block Diagram
VCC
8-BIT DATA BUS
INTERNAL
OSCILLATOR
TUNABLE
INTERNAL
OSCILLATOR
TIMING AND
CONTROL
GND
PROGRAM
COUNTER
STACK
POINTER
WATCHDOG
TIMER
PROGRAM
FLASH
HARDWARE
STACK
MCU CONTROL
REGISTER
INSTRUCTION
REGISTER
GENERAL
PURPOSE
REGISTERS
INSTRUCTION
DECODER
Z
TIMER/
COUNTER0
ALU
TIMER/
COUNTER1
STATUS
REGISTER
INTERRUPT
UNIT
ISP MODULE
DATA
EEPROM
CONTROL
LINES
PROGRAMMING
LOGIC
MCU STATUS
REGISTER
ANALOG
COMPARATOR
+
-
ANALOG MUX
DATA REGISTER
PORT B
ADC
DATA DIR.
REG.PORT B
PORT B DRIVERS
PB0-PB5
3
1187D–12/01
Pin Descriptions
VCC
Supply voltage pin.
GND
Ground pin.
Port B (PB5..PB0)
Port B is a 6-bit I/O port. PB4..0 are I/O pins that can provide internal pull-ups (selected
for each bit). PB5 is input or open-drain output. The use of pin PB5 is defined by a fuse
and the special function associated with this pin is external Reset. The port pins are tristated when a reset condition becomes active, even if the clock is not running.
Port B also accommodates analog I/O pins. The Port B pins with alternate functions are
shown in Table 1.
Table 1. Port B Alternate Functions
Port Pin
Alternate Function
PB0
MOSI (Data Input Line for Memory Downloading)
AREF (ADC Voltage Reference)
AIN0 (Analog Comparator Positive Input)
PB1
MISO (Data Output Line for Memory Downloading)
OC1A (Timer/Counter PWM Output)
AIN1 (Analog Comparator Negative Input)
PB2
SCK (Serial Clock Input for Serial Programming)
INT0 (External Interrupt0 Input)
ADC1 (ADC Input Channel 1)
T0 (Timer/Counter0 External Counter Input)
PB3
ADC2 (ADC Input Channel 2)
PB4
ADC3 (ADC Input Channel 3)
PB5
RESET (External Reset Pin)
ADC0 (ADC Input Channel 0)
Analog Pins
Up to four analog inputs can be selected as inputs to Analog-to-Digital Converter (ADC).
Internal Oscillators
The internal oscillator provides a clock rate of nominally 1.6 MHz for the system clock
(CK). Due to large initial variation (0.8 -1.6 MHz) of the internal oscillator, a tuning capability is built in. Through an 8-bit control register – OSCCAL – the system clock rate can
be tuned with less than 1% steps of the nominal clock.
There is an internal PLL that provides a 16x clock rate locked to the system clock (CK)
for the use of the Peripheral Timer/Counter1. The nominal frequency of this peripheral
clock, PCK, is 25.6 MHz.
4
ATtiny15L
1187D–12/01
ATtiny15L
ATtiny15L
Architectural
Overview
The fast-access register file concept contains 32 x 8-bit general purpose working registers with a single-clock-cycle access time. This means that during one single clock
cycle, one ALU (Arithmetic Logic Unit) operation is executed. Two operands are output
from the register file, the operation is executed, and the result is stored back in the register file – in one clock cycle.
Two of the 32 registers can be used as a 16-bit pointer for indirect memory access. This
pointer is called the Z-pointer, and can address the register file, IO file and the Flash
program memory.
Figure 2. The ATtiny15L AVR RISC Architecture
Data Bus 8-bit
Control
Registrers
512 x 16
Program
FLASH
Program
Counter
Status
and Test
32 x 8
General
Purpose
Registrers
Instruction
Register
Direct Addressing
Instruction
Decoder
ALU
Interrupt
Unit
SPI Unit
2 x 8-bit
Timer/Counter
Watchdog
Timer
Control Lines
ADC
64 x 8
EEPROM
Analog
Comparator
I/O Lines
The ALU supports arithmetic and logic functions between registers or between a constant and a register. Single-register operations are also executed in the ALU. Figure 2
shows the ATtiny15L AVR RISC microcontroller architecture. The AVR uses a Harvard
architecture concept with separate memories and buses for program and data memories. The program memory is accessed with a two-stage pipeline. While one instruction
is being executed, the next instruction is pre-fetched from the program memory. This
concept enables instructions to be executed in every clock cycle. The program memory
is In-System Programmable Flash memory.
With the relative jump and relative call instructions, the whole address space is directly
accessed. All AVR instructions have a single 16-bit word format, meaning that every
program memory address contains a single 16-bit instruction.
During interrupts and subroutine calls, the return address program counter (PC) is
stored on the stack. The stack is a 3-level-deep hardware stack dedicated for subroutines and interrupts.
The I/O memory space contains 64 addresses for CPU peripheral functions as Control
Registers, Timer/Counters and other I/O functions. The memory spaces in the AVR
architecture are all linear and regular memory maps.
5
1187D–12/01
A flexible interrupt module has its control registers in the I/O space with an additional
global interrupt enable bit in the status register. All the different interrupts have a separate interrupt vector in the interrupt vector table at the beginning of the program
memory. The different interrupts have priority in accordance with their interrupt vector
position. The lower the interrupt vector address, the higher the priority.
The General Purpose
Register File
Figure 3 shows the structure of the 32 general purpose registers in the CPU.
Figure 3. AVR CPU General Purpose Working Registers
7
0
R0
R1
R2
General
…
Purpose
…
Working
R28
Registers
R29
R30 (Z-register low byte)R3
R31 (Z-register high byte)
All the register operating instructions in the instruction set have direct- and single-cycle
access to all registers. The only exception is the five constant arithmetic and logic
instructions SBCI, SUBI, CPI, ANDI, and ORI between a constant and a register and the
LDI instruction for load-immediate constant data. These instructions apply to the second
half of the registers in the register file – R16..R31. The general SBC, SUB, CP, AND,
OR, and all other operations between two registers or on a single-register apply to the
entire register file.
Registers 30 and 31 form a 16-bit pointer (the Z-pointer) which is used for indirect Flash
memory and register file access. When the Register file is accessed, the contents of
R31 is discarded by the CPU.
The ALU – Arithmetic
Logic Unit
The high-performance AVR ALU operates in direct connection with all the 32 general
purpose working registers. Within a single clock cycle, ALU operations between registers in the register file are executed. The ALU operations are divided into three main
categories – arithmetic, logic and bit-functions. Some microcontrollers in the AVR product family feature a hardware multiplier in the arithmetic part of the ALU.
The Flash Program
Memory
The ATtiny15L contains 1K byte On-chip, In-System Programmable Flash memory for
program storage. Since all instructions are single 16-bit words, the Flash is organized as
512 x 16 words. The Flash memory has an endurance of at least 1,000 write/erase
cycles.
The ATtiny15L Program Counter is 9 bits wide, thus addressing the 512 words Flash
program memory.
See page 54 for a detailed description on Flash memory programming.
6
ATtiny15L
1187D–12/01
ATtiny15L
The Program and Data
Addressing Modes
The ATtiny15L AVR RISC Microcontroller supports powerful and efficient addressing
modes. This section describes the various addressing modes supported in the
ATtiny15L. In the figures, OP means the operation code part of the instruction word. To
simplify, not all figures show the exact location of the addressing bits.
Register Direct, Singleregister Rd
Figure 4. Direct Single-register Addressing
The operand is contained in register d (Rd).
Register Indirect
Figure 5. Indirect Register Addressing
REGISTER FILE
0
Z-register
30
31
The register accessed is the one pointed to by the Z-register low byte (R30).
Register Direct, Two Registers
Rd and Rr
Figure 6. Direct Register Addressing, Two Registers
7
1187D–12/01
Operands are contained in register r (Rr) and d (Rd). The result is stored in register d
(Rd).
I/O Direct
Figure 7. I/O Direct Addressing
Operand address is contained in 6 bits of the instruction word. “n” is the destination or
source register address.
Relative Program Addressing,
RJMP and RCALL
Figure 8. Relative Program Memory Addressing
+1
Program execution continues at address PC + k + 1. The relative address k is -2048 to
2047.
Constant Addressing using
the LPM Instruction
Figure 9. Code Memory Constant Addressing
$1FF
8
ATtiny15L
1187D–12/01
ATtiny15L
Constant byte address is specified by the Z-register contents. The 15 MSBs select word
address (0 - 511), and LSB selects low byte if cleared (LSB = 0) or high byte if set
(LSB = 1).
Subroutine and Interrupt
Hardware Stack
The ATtiny15L uses a 3-level-deep hardware stack for subroutines and interrupts. The
hardware stack is 9 bits wide and stores the Program Counter (PC) return address while
subroutines and interrupts are executed.
RCALL instructions and interrupts push the PC return address onto stack level 0, and
the data in the other stack levels 1 - 2 are pushed one level deeper in the stack. When a
RET or RETI instruction is executed the returning PC is fetched from stack level 0, and
the data in the other stack levels 1 - 2 are popped one level in the stack.
If more than three subsequent subroutine calls or interrupts are executed, the first values written to the stack are overwritten. Pushing four return addresses A1, A2, A3, and
A4 followed by four subroutine or interrupt returns, will pop A4, A3, A2, and once more
A2 from the hardware stack.
The EEPROM Data
Memory
The ATtiny15L contains 64 bytes of data EEPROM memory. It is organized as a separate data space, in which single bytes can be read and written. The EEPROM has an
endurance of at least 100,000 write/erase cycles. The access between the EEPROM
and the CPU is described on page 36, specifying the EEPROM Address Register, the
EEPROM Data Register, and the EEPROM Control Register.
Memory Access and
Instruction Execution Timing
This section describes the general access timing concepts for instruction execution and
internal memory access.
The AVR CPU is driven by the System Clock Ø, directly generated from the external
clock crystal for the chip. No internal clock division is used.
Figure 10 shows the parallel instruction fetches and instruction executions enabled by
the Harvard architecture and the fast-access register file concept. This is the basic pipelining concept to obtain up to 1 MIPS per MHz with the corresponding unique results for
functions per cost, functions per clocks, and functions per power-unit.
Figure 10. The Parallel Instruction Fetches and Instruction Executions
T1
T2
T3
T4
System Clock Ø
1st Instruction Fetch
1st Instruction Execute
2nd Instruction Fetch
2nd Instruction Execute
3rd Instruction Fetch
3rd Instruction Execute
4th Instruction Fetch
Figure 11 shows the internal timing concept for the register file. In a single clock cycle
an ALU operation using two register operands is executed, and the result is stored back
to the destination register.
9
1187D–12/01
Figure 11. Single Cycle ALU Operation
T1
T2
T3
T4
System Clock Ø
Total Execution Time
Register Operands Fetch
ALU Operation Execute
Result Write Back
I/O Memory
The I/O space definition of the ATtiny15L is shown in Table 2.
Table 2. ATtiny15L I/O Space(1)
10
Address Hex
Name
Function
$3F
SREG
Status Register
$3B
GIMSK
General Interrupt Mask Register
$3A
GIFR
General Interrupt Flag Register
$39
TIMSK
Timer/Counter Interrupt Mask Register
$38
TIFR
Timer/Counter Interrupt Flag Register
$35
MCUCR
MCU Control Register
$34
MCUSR
MCU Status Register
$33
TCCR0
Timer/Counter0 Control Register
$32
TCNT0
Timer/Counter0 (8-bit)
$31
OSCCAL
Oscillator Calibration Register
$30
TCCR1
Timer/Counter1 Control Register
$2F
TCNT1
Timer/Counter1 (8-bit)
$2E
OCR1A
Timer/Counter1 Output Compare Register A
$2D
OCR1B
Timer/Counter1 Output Compare Register B
$2C
SFIOR
Special Function I/O Register
$21
WDTCR
Watchdog Timer Control Register
$1E
EEAR
EEPROM Address Register
$1D
EEDR
EEPROM Data Register
$1C
EECR
EEPROM Control Register
$18
PORTB
Data Register, Port B
$17
DDRB
Data Direction Register, Port B
$16
PINB
Input Pins, Port B
$08
ACSR
Analog Comparator Control and Status Register
$07
ADMUX
ADC Multiplexer Select Register
ATtiny15L
1187D–12/01
ATtiny15L
Table 2. ATtiny15L I/O Space(1) (Continued)
Address Hex
Note:
Name
Function
$06
ADCSR
ADC Control and Status Register
$05
ADCH
ADC Data Register High
$04
ADCL
ADC Data Register Low
1. Reserved and unused locations are not shown in the table.
All ATtiny15L I/O and peripheral registers are placed in the I/O space. The I/O locations
are accessed by the IN and OUT instructions transferring data between the 32 general
purpose working registers and the I/O space. I/O registers within the address range $00
- $1F are directly bit-accessible using the SBI and CBI instructions. In these registers,
the value of single bits can be checked by using the SBIS and SBIC instructions. Refer
to the instruction set chapter for more details. For compatibility with future devices,
reserved bits should be written zero if accessed. Reserved I/O memory addresses
should never be written.
The I/O and peripheral control registers are explained in the following sections.
The Status Register – SREG
The AVR status register – SREG – at I/O space location $3F is defined as:
Bit
7
6
5
4
3
2
1
0
$3F
I
T
H
S
V
N
Z
C
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
SREG
• Bit 7 – I: Global Interrupt Enable
The global interrupt enable bit must be set (one) for the interrupts to be enabled. The
individual interrupt enable control is then performed in the interrupt mask registers –
GIMSK and TIMSK. If the global interrupt enable register is cleared (zero), none of the
interrupts are enabled independent of the GIMSK and TIMSK values. The I-bit is cleared
by hardware after an interrupt has occurred, and is set by the RETI instruction to enable
subsequent interrupts.
• Bit 6 – T: Bit Copy Storage
The bit copy instructions BLD (Bit LoaD) and BST (Bit STore) use the T-bit as source
and destination for the operated bit. A bit from a register in the register file can be copied
into T by the BST instruction, and a bit in T can be copied into a bit in a register in the
register file by the BLD instruction.
• Bit 5 – H: Half-carry Flag
The half-carry flag H indicates a half-carry in some arithmetic operations. See the
Instruction Set description for detailed information.
• Bit 4 – S: Sign Bit, S = N ⊕ V
The S-bit is always an exclusive or between the negative flag N and the two’s complement overflow flag V. See the Instruction Set description for detailed information.
• Bit 3 – V: Two’s Complement Overflow Flag
The two’s complement overflow flag V supports two’s complement arithmetics. See the
Instruction Set description for detailed information.
• Bit 2 – N: Negative Flag
The negative flag N indicates a negative result after the different arithmetic and logic
operations. See the Instruction Set description for detailed information.
11
1187D–12/01
• Bit 1 – Z: Zero Flag
The zero flag Z indicates a zero result after the different arithmetic and logic operations.
See the Instruction Set description for detailed information.
• Bit 0 – C: Carry Flag
The carry flag C indicates a carry in an arithmetic or logic operation. See the Instruction
Set description for detailed information.
Reset and Interrupt
Handling
The ATtiny15L provides eight interrupt sources. These interrupts and the separate reset
vector each have a separate program vector in the program memory space. All the interrupts are assigned individual enable bits that must be set (one) together with the I-bit in
the status register in order to enable the interrupt.
The lowest addresses in the program memory space are automatically defined as the
Reset and Interrupt vectors. The complete list of vectors is shown in Table 3. The list
also determines the priority levels of the different interrupts. The lower the address the
higher is the priority level. RESET has the highest priority, and next is INT0 (the External
Interrupt Request 0), etc.
Table 3. Reset and Interrupt Vectors
Vector No.
Program Address
Source
Interrupt Definition
1
$000
RESET
External Reset, Power-on Reset,
Brown-out Reset, and Watchdog
Reset
2
$001
INT0
3
$002
I/O Pins
4
$003
TIMER1, COMPA
5
$004
TIMER1, OVF
Timer/Counter1 Overflow
6
$005
TIMER0, OVF
Timer/Counter0 Overflow
7
$006
EE_RDY
8
$007
ANA_COMP
9
$008
ADC
External Interrupt Request 0
Pin Change Interrupt
Timer/Counter1 Compare Match A
EEPROM Ready
Analog Comparator
ADC Conversion Complete
The most typical and general program setup for the Reset and Interrupt Vector
Addresses are:
Address
Labels
Code
Comments
$000
rjmp
RESET
; Reset handler
$001
rjmp
EXT_INT0
; IRQ0 handler
$002
rjmp
PIN_CHANGE
; Pin change handler
$003
rjmp
TIM1_CMP
; Timer1 compare match
$004
rjmp
TIM1_OVF
; Timer1 overflow handler
$005
rjmp
TIM0_OVF
; Timer0 overflow handler
$006
rjmp
EE_RDY
; EEPROM Ready handler
$007
rjmp
ANA_COMP
; Analog Comparator handler
$008
rjmp
ADC
; ADC Conversion Handler
MAIN:
<instr>
xxx
; Main program start
…
…
;
$009
…
12
…
ATtiny15L
1187D–12/01
ATtiny15L
ATtiny15L Reset Sources
The ATtiny15L has four sources of reset:
•
Power-on Reset. The MCU is reset when the supply voltage is below the Power-on
Reset threshold (VPOR).
•
External Reset. The MCU is reset when a low-level is present on the RESET pin for
more than 500 ns.
•
Watchdog Reset. The MCU is reset when the Watchdog Timer period expires, and
the Watchdog is enabled.
•
Brown-out Reset. The MCU is reset when the supply voltage VCC is below the
Brown-out Reset threshold (VBOT).
During reset, all I/O registers are then set to their initial values, and the program starts
execution from address $000. The instruction placed in address $000 must be an RJMP
(relative jump) instruction to the reset handling routine. If the program never enables an
interrupt source, the interrupt vectors are not used, and regular program code can be
placed at these locations. The circuit diagram in Figure 12 shows the reset logic. Table 4
and Table 5 define the timing and electrical parameters of the reset circuitry. Note that
the register file is unchanged by a reset.
Figure 12. Reset Logic
DATA BUS
PORF
BORF
EXTRF
WDRF
MCU Status
Register (MCUSR)
Power-on Reset
Circuit
BODEN
BODLEVEL
Brown-out
Reset Circuit
Reset Circuit
Watchdog
Timer
Watchdog
Oscillator
Tunable Internal
Oscillator
CK
Delay Counters
TIMEOUT
CKSEL[1:0]
13
1187D–12/01
Table 4. Reset Characteristics (VCC = 5.0V)(1)
Symbol
Parameter
Condition
Min
Typ
Max
Units
Power-on Reset Threshold
Voltage (rising)
BOD disabled
1.0
1.4
1.8
V
BOD enabled
1.7
2.2
2.7
V
Power-on Reset Threshold
Voltage (falling)(1)
BOD disabled
0.4
0.6
0.8
V
BOD enabled
1.7
2.2
2.7
V
–
–
0.85 VCC
V
(BODLEVEL = 1)
2.6
2.7
2.8
V
(BODLEVEL = 0)
3.8
4.0
4.2
V
VPOT
VRST
RESET Pin Threshold
Voltage
VBOT
Brown-out Reset Threshold
Voltage
Note:
1. The Power-on Reset will not work unless the supply voltage has been below VPOT
(falling).
Table 5. Reset Delay Selections(1)
BODEN(2)
CKSEL
[1:0](2)
Start-up Time,
tTOUT at
VCC = 2.7V
Start-up Time,
tTOUT at
VCC = 5.0V
x
00
256 ms + 18 CK
64 ms + 18 CK
BOD disabled, slowly rising
power
x
01
256 ms + 18 CK
64 ms + 18 CK
BOD disabled, slowly rising
power
x
10
16 ms + 18 CK
4 ms + 18 CK
BOD disabled, quickly rising
power
1
11
18 CK + 32 µs
18 CK + 8 µs
BOD disabled
11
18 CK + 128 µs
18 CK + 32 µs
BOD enabled
0
Notes:
Recommended Usage
1. On power-up, the start-up time is increased with typical 0.6 ms.
2. “0” means programmed, “1” means unprogrammed.
Table 5 shows the start-up times from Reset. When the CPU wakes up from Powerdown, only the clock-counting part of the start-up time is used. The Watchdog Oscillator
is used for timing the real-time part of the start-up time. The number Watchdog Oscillator cycles used for each time-out is shown in Table 6.
The frequency of the Watchdog Oscillator is voltage dependent as shown in the Electrical Characteristics section on page 64. The device is shipped with CKSEL = “00”.
14
ATtiny15L
1187D–12/01
ATtiny15L
Table 6. Number of Watchdog Oscillator Cycles
Power-on Reset
VCC Conditions
Time-out
Number of Cycles
2.7V
32 µs
8
2.7V
128 µs
32
2.7V
16 ms
4K
2.7V
256 ms
64K
5.0V
8 µs
8
5.0V
32 µs
32
5.0V
4 ms
4K
5.0V
64 ms
64K
A Power-on Reset (POR) pulse is generated by an On-chip Detection circuit. The detection level is nominally defined in Table 4. The POR is activated whenever VCC is below
the detection level. The POR circuit can be used to trigger the Start-up Reset, as well as
detect a failure in supply voltage.
A Power-on Reset (POR) circuit ensures that the device is reset from Power-on. Reaching the Power-on Reset threshold voltage invokes a delay counter, which determines
the delay, for which the device is kept in RESET after VCC rise. The time-out period of
the delay counter can be defined by the user through the CKSEL fuses. The different
selections for the delay period are presented in Table 5. The RESET signal is activated
again, without any delay, when the VCC decreases below detection level.
Figure 13. “MCU Start-up, RESET Tied to VCC
VCC
RESET
TIME-OUT
VPOT
VRST
tTOUT
INTERNAL
RESET
15
1187D–12/01
Figure 14. MCU Start-up, RESET Extended Externally
VCC
RESET
VPOT
VRST
TIME-OUT
tTOUT
INTERNAL
RESET
External Reset
An External Reset is generated by a low-level on the RESET pin. Reset pulses longer
than 500 ns will generate a reset, even if the clock is not running. Shorter pulses are not
guaranteed to generate a reset. When the applied signal reaches the Reset Threshold
Voltage (VRST) on its positive edge, the delay timer starts the MCU after the Time-out
period tTOUT has expired.
Figure 15. External Reset during Operation
Brown-out Detection
ATtiny15L has an On-chip Brown-out Detection (BOD) circuit for monitoring the VCC
level during the operation. The BOD circuit can be enabled/disabled by the fuse
BODEN. When BODEN is enabled (BODEN programmed), and VCC decreases below
the trigger level, the Brown-out Reset is immediately activated. When VCC increases
above the trigger level, the Brown-out Reset is deactivated after a delay. The delay is
defined by the user in the same way as the delay of POR signal, in Table 5. The trigger
level for the BOD can be selected by the fuse BODLEVEL to be 2.7V (BODLEVEL
unprogrammed), or 4.0V (BODLEVEL programmed). The trigger level has a hysteresis
of 50 mV to ensure spike-free Brown-out Detection.
The BOD circuit will only detect a drop in VCC if the voltage stays below the trigger level
for longer than 3 µs for trigger level 4.0V, 7 µs for trigger level 2.7V (typical values).
16
ATtiny15L
1187D–12/01
ATtiny15L
Figure 16. Brown-out Reset during Operation(1)
VCC
VBOT+
VBOT-
RESET
tTOUT
TIME-OUT
INTERNAL
RESET
Note:
Watchdog Reset
1. The hysteresis on VBOT: VBOT+ = VBOT + 25 mV, VBOT- = VBOT - 25 mV.
When the Watchdog times out, it will generate a short reset pulse of 1 CK cycle duration. On the falling edge of this pulse, the delay timer starts counting the time-out period
tTOUT. Refer to page 34 for details on operation of the Watchdog Timer.
Figure 17. Watchdog Reset during Operation
1 CK Cycle
MCU Status Register –
MCUSR
The MCU Status Register provides information on which reset source caused an MCU
reset.
Bit
7
6
5
4
3
2
1
0
$34
–
–
–
–
WDRF
BORF
EXTRF
PORF
Read/Write
R
R
R
R
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
MCUSR
See Bit Description
• Bit 7..4 – Res: Reserved Bits
These bits are reserved bits in the ATtiny15L and always read as zero.
• Bit 3 – WDRF: Watchdog Reset Flag
This bit is set (one) if a Watchdog Reset occurs. The bit is reset (zero) by a Power-on
Reset, or by writing a logical “0” to the flag.
• Bit 2 – BORF: Brown-out Reset Flag
This bit is set (one) if a Brown-out Reset occurs. The bit is reset (zero) by a Power-on
Reset, or by writing a logical “0” to the flag.
17
1187D–12/01
• Bit 1 – EXTRF: External Reset Flag
This bit is set (one) if a External Reset occurs. The bit is reset (zero) by a Power-on
Reset, or by writing a logical “0” to the flag.
• Bit 0 – PORF: Power-on Reset Flag
This bit is set (one) if a Power-on Reset occurs. The bit is reset (zero) by writing a logical
“0” to the flag.
To make use of the reset flags to identify a reset condition, the user should read and
then reset the MCUSR as early as possible in the program. If the register is cleared
before another reset occurs, the source of the reset can be found by examining the reset
flags.
Internal Voltage
Reference
ATtiny15L features an internal bandgap reference with a nominal voltage of 1.22V. This
reference is used for Brown-out Detection, and it can be used as an input to the Analog
Comparator. The 2.56V reference to the ADC is generated from the internal bandgap
reference.
Voltage Reference Enable
Signals and Start-up Time
The voltage reference has a start-up time that may influence the way it should be used.
The maximum start-up time is TBD. To save power, the reference is not always turned
on. The reference is on during the following situations:
1. When the BOD is enabled (by programming the BODEN fuse).
2. When the bandgap reference is connected to the Analog Comparator (by setting
the AINBG bit in ACSR).
3. When the ADC is enabled.
Thus, when the BOD is not enabled, after setting the AINBG bit, the user must always
allow the reference to start-up before the output from the Analog Comparator is used.
The bandgap reference uses typically 10 µA, and to reduce power consumption in
Power-down mode, the user can avoid the three conditions above to ensure that the reference is turned off before entering Power-down mode.
Interrupt Handling
The ATtiny15L has two 8-bit Interrupt Mask control registers: GIMSK (General Interrupt
Mask register) and TIMSK (Timer/Counter Interrupt Mask register).
When an interrupt occurs, the Global Interrupt Enable I-bit is cleared (zero) and all interrupts are disabled. The user software can set the I-bit (one) to enable interrupts. The Ibit is set (one) when a Return from Interrupt instruction (RETI) is executed.
When the Program Counter is vectored to the actual interrupt vector in order to execute
the interrupt handling routine, hardware clears the corresponding flag that generated the
interrupt. Some of the interrupt flags can also be cleared by writing a logical “1” to the
flag bit position(s) to be cleared.
If an interrupt condition occurs when the corresponding interrupt enable bit is cleared
(zero), the interrupt flag will be set and remembered until the interrupt is enabled, or the
flag is cleared by software.
If one or more interrupt conditions occur when the global interrupt enable bit is cleared
(zero), the corresponding interrupt flag(s) will be set and remembered until the global
interrupt enable bit is set (one), and will be executed by order of priority.
Note that external level interrupt does not have a flag, and will only be remembered for
as long as the interrupt condition is present.
18
ATtiny15L
1187D–12/01
ATtiny15L
Note that the Status Register is not automatically stored when entering an interrupt routine and restored when returning from an interrupt routine. This must be handled by
software.
Interrupt Response Time
The interrupt execution response for all the enabled AVR interrupts is four clock cycles
minimum. After the four clock cycles the program vector address for the actual interrupt
handling routine is executed. During this 4-clock-cycle period, the Program Counter (9
bits) is pushed onto the Stack. The vector is often a relative jump to the interrupt routine,
and this jump takes two clock cycles. If an interrupt occurs during execution of a multicycle instruction, this instruction is completed before the interrupt is served. If an interrupt occurs when the MCU is in Sleep mode, the interrupt execution response time is
increased by four clock cycles.
A return from an interrupt handling routine takes four clock cycles. During these four
clock cycles, the Program Counter (9 bits) is popped back from the Stack. When AVR
exits from an interrupt, it will always return to the main program and execute one more
instruction before any pending interrupt is served.
The General Interrupt Mask
Register – GIMSK
Bit
7
6
5
4
3
2
1
0
$3B
–
INT0
PCIE
–
–
–
–
–
Read/Write
R
R/W
R/W
R
R
R
R
R
Initial Value
0
0
0
0
0
0
0
0
GIMSK
• Bit 7 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny15L and always reads as zero.
• Bit 6 – INT0: External Interrupt Request 0 Enable
When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one),
the external pin interrupt is activated. The Interrupt Sense Control0 bits 1/0 (ISC01 and
ISC00) in the MCU general Control Register (MCUCR) define whether the external
interrupt is activated on rising or falling edge, on pin change, or low level of the INT0 pin.
Activity on the pin will cause an interrupt request even if INT0 is configured as an output.
The corresponding interrupt of External Interrupt Request 0 is executed from program
memory address $001. See also “External Interrupts.”
• Bit 5 – PCIE: Pin Change Interrupt Enable
When the PCIE bit is set (one) and the I-bit in the Status Register (SREG) is set (one),
the interrupt on pin change is enabled. Any change on any input or I/O pin will cause an
interrupt. The corresponding interrupt of Pin Change Interrupt Request is executed from
program memory address $002. See also “Pin Change Interrupt.”
• Bits 4..0 – Res: Reserved Bits
These bits are reserved bits in the ATtiny15L and always read as zero.
The General Interrupt Flag
Register – GIFR
Bit
7
6
5
4
3
2
1
0
$3A
–
INTF0
PCIF
–
–
–
–
–
Read/Write
R
R/W
R/W
R
R
R
R
R
Initial Value
0
0
0
0
0
0
0
0
GIFR
• Bit 7 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny15L and always reads as zero.
19
1187D–12/01
• Bit 6 – INTF0: External Interrupt Flag0
When an edge or logic change on the INT0 pin triggers an interrupt request, INTF0
becomes set (one). If the I-bit in SREG and the INT0 bit in GIMSK are set (one), the
MCU will jump to the interrupt vector at address $001. The flag is cleared when the
interrupt routine is executed. Alternatively, the flag can be cleared by writing a logical “1”
to it. The flag is always cleared when INT0 is configured as level interrupt.
• Bit 5 – PCIF: Pin Change Interrupt Flag
When an event on any input or I/O pin triggers an interrupt request, PCIF becomes set
(one). If the I-bit in SREG and the PCIE bit in GIMSK are set (one), the MCU will jump to
the interrupt vector at address $002. The flag is cleared when the interrupt routine is
executed. Alternatively, the flag can be cleared by writing a logical “1” to it.
• Bits 4..0 – Res: Reserved Bits
These bits are reserved bits in the ATtiny15L and always read as zero.
The Timer/Counter Interrupt
Mask Register – TIMSK
Bit
7
6
5
4
3
2
1
0
$39
–
OCIE1A
–
–
–
TOIE1
TOIE0
–
Read/Write
R
R/W
R
R
R
R/W
R/W
R
Initial Value
0
0
0
0
0
0
0
0
TIMSK
• Bit 7 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny15L and always reads as zero.
• Bit 6 – OCIE1A: Timer/Counter1 Output Compare Interrupt Enable
When the OCIE1A bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter1 Compare Match, interrupt is enabled. The corresponding interrupt (at
vector $003) is executed if a compare match A in Timer/Counter1 occurs, i.e., when the
OCF1A bit is set (one) in the Timer/Counter Interrupt Flag Register (TIFR).
• Bit 5..3 – Res: Reserved Bits
These bits are reserved bits in the ATtiny15L and always read as zero.
• Bit 2 – TOIE1: Timer/Counter1 Overflow Interrupt Enable
When the TOIE1 bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter1 Overflow interrupt is enabled. The corresponding interrupt (at vector
$004) is executed if an overflow in Timer/Counter1 occurs, i.e., when the TOV1 bit is set
(one) in the Timer/Counter Interrupt Flag Register (TIFR).
• Bit 1 – TOIE0: Timer/Counter0 Overflow Interrupt Enable
When the TOIE0 bit is set (one) and the I-bit in the Status Register is set (one), the
Timer/Counter0 Overflow interrupt is enabled. The corresponding interrupt (at vector
$005) is executed if an overflow in Timer/Counter0 occurs, i.e., when the TOV0 bit is set
(one) in the Timer/Counter Interrupt Flag Register (TIFR).
• Bit 0 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny15L and always reads as zero.
20
ATtiny15L
1187D–12/01
ATtiny15L
The Timer/Counter Interrupt
Flag Register – TIFR
Bit
7
6
5
4
3
2
1
0
$38
–
OCF1A
–
–
–
TOV1
TOV0
–
Read/Write
R
R/W
R
R
R
R/W
R/W
R
Initial Value
0
0
0
0
0
0
0
0
TIFR
• Bit 7 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny15L and always reads as zero.
• Bit 6 – OCF1A: Output Compare Flag 1A
The OCF1A bit is set (one) when compare match occurs between Timer/Counter1 and
the data value in OCR1A (Output Compare Register 1A). OCF1A is cleared by hardware when executing the corresponding interrupt handling vector. Alternatively, OCF1A
is cleared by writing a logical “1” to the flag. When the I-bit in SREG, OCIE1A, and
OCF1A are set (one), the Timer/Counter1 compare match A interrupt is executed.
• Bits 5..3 – Res: Reserved bits
These bits are reserved bits in the ATtiny15L and always read as zero.
• Bit 2 – TOV1: Timer/Counter1 Overflow Flag
The bit TOV1 is set (one) when an overflow occurs in Timer/Counter1. TOV1 is cleared
by hardware when executing the corresponding interrupt handling vector. Alternatively,
TOV1 is cleared by writing a logical “1” to the flag. When the SREG I-bit, TOIE1
(Ti mer /Counter 1 O v erfl ow Inte rr upt Enabl e) and TOV 1 ar e s et ( one ), the
Timer/Counter1 Overflow interrupt is executed.
• Bit 1 – TOV0: Timer/Counter0 Overflow Flag
The bit TOV0 is set (one) when an overflow occurs in Timer/Counter0. TOV0 is cleared
by hardware when executing the corresponding interrupt handling vector. Alternatively,
TOV0 is cleared by writing a logical “1” to the flag. When the SREG I-bit, TOIE0
(Ti mer /Counter 0 O v erfl ow Inte rr upt Enabl e) and TOV 0 ar e s et ( one ), the
Timer/Counter0 Overflow interrupt is executed.
• Bit 0 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny15L and always reads as zero.
External Interrupt
The external interrupt is triggered by the INT0 pin. Observe that, if enabled, the interrupt
will trigger even if the INT0 pin is configured as an output. This feature provides a way of
generating a software interrupt. The external interrupt can be triggered by a falling or rising edge, a pin change, or a low level. This is set up as indicated in the specification for
the MCU Control Register (MCUCR). When the external interrupt is enabled and is configured as level-triggered, the interrupt will trigger as long as the pin is held low.
The external interrupt is set up as described in the specification for the MCU Control
Register (MCUCR).
Pin Change Interrupt
The pin change interrupt is triggered by any change in logical value on any input or I/O
pin. Change on pins PB4..0 will always cause an interrupt. Change on pin PB5 will
cause an interrupt if the pin is configured as input or I/O, as described in the section “Pin
Descriptions” on page 4. Observe that, if enabled, the interrupt will trigger even if the
changing pin is configured as an output. This feature provides a way of generating a
software interrupt. Also observe that the pin change interrupt will trigger even if the pin
activity triggers another interrupt, for example the external interrupt. This implies that
one external event might cause several interrupts. The values on the pins are sampled
before detecting edges. If pin change interrupt is enabled, pulses that last longer than
21
1187D–12/01
one CPU clock period will generate an interrupt. Shorter pulses are not guaranteed to
generate an interrupt.
The MCU Control Register –
MCUCR
The MCU Control Register contains control bits for general MCU functions.
Bit
7
6
5
4
3
2
1
0
$35
–
PUD
SE
SM1
SM0
–
ISC01
ISC00
Read/Write
R
R/W
R/W
R/W
R/W
R
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
MCUCR
• Bits 7 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny15L and always reads as zero.
• Bit 6- PUD: Pull-up Disable
This PUD bit must be set (one) to disable internal pull-up registers at Port B.
• Bit 5 – SE: Sleep Enable
The SE bit must be set (one) to make the MCU enter the sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmer’s purpose, it is recommended to set the Sleep Enable SE bit just before the
execution of the SLEEP instruction.
• Bits 4, 3 – SM1, SM0: Sleep Mode Select Bits 1 and 0
These bits select between the three available sleep modes, as shown in Table 7.
Table 7. Sleep Modes
SM1
SM0
Sleep Mode
0
0
Idle mode
0
1
ADC Noise Reduction mode
1
0
Power-down mode
1
1
Reserved
For details, refer to “Sleep Modes” below.
• Bit 2 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny15L and always reads as zero.
• Bits 1, 0 – ISC01, ISC00: Interrupt Sense Control 0 Bit 1 and Bit 0
The External Interrupt 0 is activated by the external pin INT0 if the SREG I-flag and the
corresponding interrupt mask is set (one). The activity on the external INT0 pin that activates the interrupt is defined in Table 8:
Table 8. Interrupt 0 Sense Control(1)
ISC01
ISC00
0
0
The low level of INT0 generates an interrupt request.
0
1
Any change on INT0 generates an interrupt request
1
0
The falling edge of INT0 generates an interrupt request.
1
1
The rising edge of INT0 generates an interrupt request.
Note:
22
Description
1. When changing the ISC10/ISC00 bits, INT0 must be disabled by clearing its Interrupt
Enable bit in the GIMSK register. Otherwise an interrupt can occur when the bits are
changed.
ATtiny15L
1187D–12/01
ATtiny15L
Sleep Modes
To enter any of the three sleep modes, the SE bit in MCUCR must be set (one) and a
SLEEP instruction must be executed. The SM1 and SM0 bits in the MCUCR register
select which sleep mode (Idle, ADC Noise Reduction or Power-down) will be activated
by the SLEEP instruction (see Table 7). If an enabled interrupt occurs while the MCU is
in a sleep mode, the MCU wakes up. The MCU is then halted for four cycles, executes
the interrupt routine and resumes execution from the instruction following SLEEP. On
wake-up from Power-down mode on pin change, the two instructions following SLEEP.
The contents of the register file, SRAM, and I/O memory are unaltered when the device
wakes up from sleep. If a reset occurs during sleep mode, the MCU wakes up and executes from the Reset vector.
Idle Mode
When the SM1/SM0 bits are “00”, the SLEEP instruction forces the MCU into the Idle
mode, stopping the CPU but allowing the ADC, Analog Comparator, Timer/Counters,
Watchdog and the Interrupt system to continue operating. This enables the MCU to
wake up from external triggered interrupts as well as internal ones like the Timer Overflow interrupt and Watchdog Reset. If the ADC is enabled, a conversion starts
automatically when this mode is entered. If wake-up from the Analog Comparator interrupt is not required, the Analog Comparator can be powered down by setting the ADCbit in the Analog Comparator Control and Status Register (ACSR). This will reduce
power consumption in Idle mode.
ADC Noise Reduction Mode
When the SM1/SM0 bits are “01”, the SLEEP instruction forces the MCU into the ADC
Noise Reduction mode, stopping the CPU but allowing the ADC, the external interrupt
pin, pin change interrupt and the Watchdog (if enabled) to continue operating. Please
note that the clock system including the PLL is also active in the ADC Noise Reduction
mode. This improves the noise environment for the ADC, enabling higher resolution
measurements. If the ADC is enabled, a conversion starts automatically when this mode
is entered. In addition to Watchdog Time-out and External Reset, only an external leveltriggered interrupt, a pin change interrupt or an ADC interrupt can wake up the MCU.
Power-down Mode
When the SM1/SM0 bits are “10”, the SLEEP instruction forces the MCU into the Powerdown mode. Only an External Reset, a Watchdog Reset (if enabled), an external leveltriggered interrupt, or a pin change interrupt can wake up the MCU.
Note that if a level-triggered or pin change interrupt is used for wake-up from Powerdown mode, the changed level must be held for some time to wake up the MCU. This
makes the MCU less sensitive to noise. The changed level is sampled twice by the
Watchdog Oscillator clock, and if the input has the required level during this time, the
MCU will wake up. The period of the waTchdog Oscillator is 2.9 µs (nominal) at 3.0V and
25°C. The frequency of the Watchdog Oscillator is voltage-dependent as shown in the
“Electrical Characteristics” section.
When waking up from the Power-down mode, a delay from the wake-up condition
occurs until the wake-up becomes effective. This allows the clock to restart and become
stable after having been stopped. The wake-up period is defined by the same CKSEL
fuses that define the reset time-out period.
23
1187D–12/01
Tunable Internal RC
Oscillator
The System Clock Oscillator
Calibration Register –
OSCCAL
The internal RC oscillator provides a fixed 1.6 MHz clock (nominal at 5V and 25°C). This
internal clock is always the system clock of the ATtiny15L. This oscillator can be calibrated by writing the calibration byte (see page 55) to the OSCCAL register.
Bit
7
6
5
4
3
2
1
0
$31
CAL7
CAL6
CAL5
CAL4
CAL3
CAL2
CAL1
CAL0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
OSCCAL
Writing the calibration byte to this address will trim the internal oscillator frequency in
order to remove process variations. When OSCCAL is zero (initial value), the lowest
available frequency is chosen. Writing non-zero values to this register will increase the
frequency of the internal oscillator. Writing $FF to the register selects the highest available frequency.
Internal PLL for Fast
Peripheral Clock
Generation
The internal PLL in ATtiny15L generates a clock frequency that is 16x multiplied from
the RC oscillator system clock. If the RC oscillator frequency is the nominal 1.6 MHz, the
fast peripheral clock is 25.6 MHz. The fast peripheral clock, or a clock prescaled from
that, can be selected as the clock source for Timer/Counter1.
The PLL is locked on the tunable internal RC oscillator and adjusting the tunable internal
RC oscillator via the OSCCAL register will adjust the fast peripheral clock at the same
time. Timer1 may malfunction if the internal RC oscillator is adjusted beyond 1.75 MHz.
It is recommended not to take the OSCCAL adjustments to a higher frequency than
1.75 MHz in order to keep proper operation of all chip functions.
24
ATtiny15L
1187D–12/01
ATtiny15L
Timer/Counters
The ATtiny15L provides two general purpose 8-bit Timer/Counters. The Timer/Counters
hav e se par ate p re sc al ing s ele cti on fr om s epar at e 1 0- bit pr es c ale rs . Th e
Timer/Counter0 uses internal clock (CK) as the clock time base. The Timer/Counter1
may use either the internal clock (CK) or the fast peripheral clock (PCK) as the clock
time base.
The Timer/Counter0
Prescaler
Figure 18 shows the Timer/Counter prescaler.
Figure 18. Timer/Counter0 Prescaler
PSR0
CK/1024
CK/256
CK/64
10-BIT T/C PRESCALER
CLEAR
CK/8
CK
T0
0
CS00
CS01
CS02
TIMER/COUNTER0 CLOCK SOURCE
TCK0
The four prescaled selections are: CK/8, CK/64, CK/256, and CK/1024, where CK is the
oscillator clock. CK, external source and stop, can also be selected as clock sources.
Setting the PSR10 bit in SFIOR resets the prescaler. This allows the user to operate
with a predictable prescaler.
The Timer/Counter1
Prescaler
Figure 19 shows the Timer/Counter1 prescaler. For Timer/Counter1 the clock selections
are: PCK, PCK/2, PCK/4, PCK/8, CK (=PCK/16), CK/2, CK/4, CK/8,CK/16, CK/32,
CK/64, CK/128, CK/256, CK/512, CK/1024, and stop. The clock options are described in
Table 12 on page 32 and the Timer/Counter1 Control Register (TCCR1). Setting the
PSR1 bit in the SFIOR register resets the 10-bit prescaler. This allows the user to operate with a predictable prescaler.
25
1187D–12/01
Figure 19. Timer/Counter1 Prescaler
CK
(1.6 MHz)
10-BIT T/C PRESCALER
CLEAR
PSR1
CK/1024
CK/256
CK/512
CK/128
CK/32
CK/64
CK/16
CK/4
CK/8
CK/2
CK (=PCK/16)
PCK/8
PCK/2
0
PCK/4
CLEAR
3-BIT T/C PRESCALER
PCK
(25.6 MHz)
CS10
CS11
CS12
CS13
TIMER/COUNTER1 CLOCK SOURCE
The Special Function IO
Register – SFIOR
Bit
7
6
5
4
3
2
1
0
$2C
–
–
–
–
–
FOC1A
PSR1
PSR0
Read/Write
R
R
R
R
R
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
SFIOR
• Bit 7..3 – Res: Reserved Bits
These bits are reserved bits in the ATtiny15L and always read as zero.
• Bit 2 – FOC1A: Force Output Compare 1A
Writing a logical “1” to this bit forces a change in the compare match output pin PB1
(OC1A) according to the values already set in COM1A1 and COM1A0. The Force Output Compare bit can be used to change the output pin without waiting for a compare
match in timer. The automatic action programmed in COM1A1 and COM1A0 happens
as if a Compare Match had occurred, but no interrupt is generated and the
Timer/Counter1 will not be cleared even if CTC1 is set. The FOC1A bit will always be
read as zero. The setting of the FOC1A bit has no effect in PWM mode.
• Bit 1 – PSR1: Prescaler Reset Timer/Counter1
When this bit is set (one) the Timer/Counter1 prescaler will be reset. The bit will be
cleared by hardware after the operation is performed. Writing a “0” to this bit will have no
effect. This bit will always be read as zero.
• Bit 0 – PSR0: Prescaler Reset Timer/Counter0
When this bit is set (one) the Timer/Counter0 prescaler will be reset. The bit will be
cleared by hardware after the operation is performed. Writing a “0” to this bit will have no
effect. This bit will always be read as zero.
26
ATtiny15L
1187D–12/01
ATtiny15L
The 8-bit Timer/Counter0 Figure 20 shows the block diagram for Timer/Counter0.
The 8-bit Timer/Counter0 can select clock source from CK, prescaled CK or an external
pin. In addition, it can be stopped as described in the specification for the
Timer/Counter0 Control Register (TCCR0). The overflow status flag is found in the
Timer/Counter Interrupt Flag Register (TIFR). Control signals are found in the
Timer/Counter0 Control Register (TCCR0). The interrupt enable/disable settings for
Timer/Counter0 are found in the Timer/Counter Interrupt Mask Register (TIMSK).
When Timer/Counter0 is externally clocked, the external signal is synchronized with the
oscillator frequency of the CPU. To ensure proper sampling of the external clock, the
minimum time between two external clock transitions must be at least one internal CPU
clock period. The external clock signal is sampled on the rising edge of the internal CPU
clock.
The 8-bit Timer/Counter0 features both a high-resolution and a high-accuracy usage
with the lower prescaling opportunities. Similarly, the high-prescaling opportunities
make the Timer/Counter0 useful for lower-speed functions or exact-timing functions with
infrequent actions.
CS00
CS01
CS02
TOV0
TOV0
TOV1
OCF1A
TOIE0
TOIE1
OCIE1A
Figure 20. Timer/Counter0 Block Diagram
T/C CLK SOURCE
The Timer/Counter0 Control
Register – TCCR0
Bit
7
6
5
4
3
2
1
0
$33
–
–
–
–
–
CS02
CS01
CS00
Read/Write
R
R
R
R
R
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
TCCR0
• Bits 7..3 – Res: Reserved Bits
These bits are reserved bits in the ATtiny15L and always read as zero.
27
1187D–12/01
• Bits 2, 1, 0 – CS02, CS01, CS00: Clock Select0, Bits 2, 1 and 0
The Clock Select0 bits 2, 1 and 0 define the prescaling source of Timer0.
Table 9. Clock 0 Prescale Select
CS02
CS01
CS00
Description
0
0
0
Stop, the Timer/Counter0 is stopped.
0
0
1
CK
0
1
0
CK/8
0
1
1
CK/64
1
0
0
CK/256
1
0
1
CK/1024
1
1
0
External Pin T0, falling edge
1
1
1
External Pin T0, rising edge
The Stop condition provides a Timer Enable/Disable function. The prescaled CK modes
are scaled directly from the CK oscillator clock. If the external pin modes are used for
Timer/Counter0, transitions on PB2/(T0) will clock the counter even if the pin is configured as an output. This feature can give the user SW control of counting.
The Timer Counter 0 – TCNT0
Bit
7
$32
MSB
6
5
4
3
2
1
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
LSB
TCNT0
The Timer/Counter0 is implemented as an up-counter with read and write access. If the
Timer/Counter0 is written and a clock source is present, the Timer/Counter0 continues
counting in the timer clock cycle following the write operation.
28
ATtiny15L
1187D–12/01
ATtiny15L
The 8-bit Timer/Counter1 This module features a high-resolution and a high-accuracy usage with the lower prescaling opportunities. Timer/Counter1 can also be used as an accurate, high speed, 8-bit
Pulse Width Modulator using clock speeds up to 25.6 MHz. In this mode,
Timer/Counter1 and the output compare registers serve as a standalone PWM. Refer to
page 34 for a detailed description of this function. Similarly, the high-prescaling opportunities make this unit useful for lower-speed functions or exact-timing functions with
infrequent actions.
Figure 21 shows the block diagram for Timer/Counter1.
Figure 21. Timer/Counter1 Block Diagram
TIMER/COUNTER1
(TCNT1)
T/C CLEAR
8-BIT COMPARATOR
8-BIT COMPARATOR
T/C1 OUTPUT
COMPARE REGISTER A
(OCR1A)
T/C1 OUTPUT
COMPARE REGISTER B
(OCR1B)
T/C1 CONTROL
LOGIC
PSR1
PSR0
SFIOR
FOC1
CS10
CS11
CS12
CS13
COM1A0
COM1A1
CTC1
T/C CONTROL
REGISTER 1 (TCCR1)
PWM1
TOV1
TOV0
OCF1A
TIMER INT. FLAG
REGISTER (TIFR)
OCF1A
TIMER INT. MASK
REGISTER (TIMSK)
T/C1 OC1A PIN/
PORT PB1
(PWM OUTPUT)
TOV1
TOIE1
T/C1 A COMPARE
MATCH IRQ
TOIE0
OCIE1A
T/C1 OVERFLOW IRQ
CK
PCK
8-BIT DATA BUS
The two status flags (overflow and compare match) are found in the Timer/Counter
Interrupt Flag Register (TIFR). Control signals are found in the Timer/Counter Control
Register (TCCR1). The interrupt enable/disable settings are found in the Timer/Counter
Interrupt Mask Register (TIMSK).
The Timer/Counter1 contains two Output Compare registers, OCR1A and OCR1B, as
the data source to be compared with the Timer/Counter1 contents. In normal mode the
Output Compare function is operational with OCR1A only, and the Output Compare
function includes optional clearing of the counter on compare match, and action on the
Output Compare Pin (PB1) (OC1A).
In PWM mode OCR1A provides the data value against which the Timer/Counter value is
compared. Upon compare match the PWM output is generated. In PWM mode The
Timer/Counter counts up to the value specified in output compare register OCR1B and
starts again from $00. This feature allows limiting the counter “full” value to a specified
29
1187D–12/01
value, lower than $FF. Together with the many prescaler options, flexible PWM frequency selection is provided. Table 14 lists clock selection and OCR1B values to obtain
PWM frequencies from 10 kHz to 150 kHz at 10 kHz steps.
The Timer/Counter1 Control
Register – TCCR1
Bit
7
6
5
4
3
2
1
0
$30
CTC1
PWM1
COM1A1
COM1A0
CS13
CS12
CS11
CS10
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
TCCR1
• Bit 7 – CTC1: Clear Timer/Counter on Compare Match
When the CTC1 control bit is set (one), Timer/Counter1 is reset to $00 in the CPU clock
cycle after a compare match with OCR1A register value. If the control bit is cleared,
Timer/Counter1 continues counting and is unaffected by a compare match.
• Bit 6 – PWM1: Pulse Width Modulator Enable
When set (one), this bit enables PWM mode for Timer/Counter1. This mode is described
on page 31.
• Bits 5,4 – COM1A1, COM1A0: Compare Output Mode, Bits 1 and 0
The COM1A1 and COM1A0 control bits determine any output pin action following a
compare match A in Timer/Counter1. Output pin actions affect pin PB1(OC1A). Since
this is an alternative function to an I/O port, the corresponding direction control bit must
be set (one) to control an output pin. The control configuration is shown in Table 10.
Table 10. Compare Mode Select(1)
COM1A1
COM1A0
0
0
Timer/Counter disconnected from output pin OC1A
0
1
Toggle the OC1A output line.
1
0
Clear the OC1A output line (to zero).
1
1
Set the OC1A output line (to one).
Note:
Description
1. In PWM mode, these bits have a different function. Refer to Table 12 for a detailed
description.When changing the COM1A1/COM1A0 bits, the Output Compare 1A
Interrupt must be disabled by clearing its Interrupt Enable bit in the TIMSK Register.
Otherwise an interrupt can occur when the bits are changed.
• Bits 3, 2, 1, 0 – CS13, CS12, CS11, CS10: Clock Select Bits 3, 2, 1, and 0
The Clock Select bits 3, 2, 1, and 0 define the prescaling source of Timer/Counter1.
Table 11. Timer/Counter1 Prescale Select
30
CS13
CS12
CS11
CS10
Description
0
0
0
0
Timer/Counter1 is stopped.
0
0
0
1
CK*16 (=PCK)
0
0
1
0
CK*8 (=PCK/2)
0
0
1
1
CK*4 (=PCK/4)
0
1
0
0
CK*2 (=PCK/8)
0
1
0
1
CK
0
1
1
0
CK/2
0
1
1
1
CK/4
ATtiny15L
1187D–12/01
ATtiny15L
Table 11. Timer/Counter1 Prescale Select (Continued)
CS13
CS12
CS11
CS10
Description
1
0
0
0
CK/8
1
0
0
1
CK/16
1
0
1
0
CK/32
1
0
1
1
CK/64
1
1
0
0
CK/128
1
1
0
1
CK/256
1
1
1
0
CK/512
1
1
1
1
CK/1024
The Stop condition provides a Timer Enable/Disable function. The prescaled CK modes
are scaled directly from the CK oscillator clock.
The Timer/Counter1 – TCNT1
Bit
7
$2F
MSB
6
5
4
3
2
1
0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
LSB
TCNT1
This 8-bit register contains the value of Timer/Counter1.
Timer/Counter1 is implemented as an up-counter with read and write access. Due to
synchronization of the CPU and Timer/Counter1, data written into Timer/Counter1 is
delayed by one CPU clock cycle.
Timer/Counter1 Output
Compare RegisterA – OCR1A
Bit
7
6
5
4
3
2
1
0
$2E
MSB
LSB
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
OCR1A
The Output Compare Register 1A is an 8-bit read/write register.
The Timer/Counter Output Compare Register 1A contains the data to be continuously
compared with Timer/Counter1. Actions on compare matches are specified in TCCR1. A
compare match occurs only if Timer/Counter1 counts to the OCR1A value. A software
write that sets TCNT1 and OCR1A to the same value does not generate a compare
match.
A compare match will set (one) the compare interrupt flag in the CPU clock cycle following the compare event.
Timer/Counter1 in PWM Mode
When the PWM mode is selected, Timer/Counter1 and the Output Compare Register A
(OCR1A) form an 8-bit, free-running and glitch-free PWM with outputs on the
PB1(OC1A) pin. Timer/Counter1 acts as an up-counter, counting up from $00 up to the
value specified in the second output compare register OCR1B, and starting from $00 up
again. When the counter value matches the contents of the Output Compare register
OCR1A, the PB1(OC1A) pin is set or cleared according to the settings of the
COM1A1/COM1A0 bits in the Timer/Counter1 Control Registers TCCR1. Refer to Table
12 for details.
31
1187D–12/01
Table 12. Compare Mode Select in PWM Mode
COM1A1
COM1A0
Effect on Compare Pin
0
0
Not connected
0
1
Not connected
1
0
Cleared on compare match (up-counting) (non-inverted PWM). Set
when TCNT1 = $00.
1
1
Set on compare match (up-counting) (inverted PWM). Cleared when
TCNT1 = $00.
Note that in PWM mode, writing to the Output Compare OCR1A, the data value is first
transferred to a temporary location. The value is latched into OCR1A when the
Timer/Counter reaches OCR1B. This prevents the occurrence of odd-length PWM
pulses (glitches) in the event of an unsynchronized OCR1A write. See Figure 22 for an
example.
Figure 22. Effects of Unsynchronized OCR Latching
Compare Value Changes
Counter Value
Compare Value
PWM Output OC1A
Synchronized OC1A Latch
Compare Value Changes
Counter Value
Compare Value
PWM Output OC1A
Unsynchronized OC1A Latch
Glitch
During the time between the write and the latch operation, a read from OCR1A will read
the contents of the temporary location. This means that the most recently written value
always will read out of OCR1A.
When OCR1A contains $00 or the top value, as specified in OCR1B register, the output
PB1(OC1A) is held low or high according to the settings of COM1A1/COM1A0. This is
shown in Table 13.
32
ATtiny15L
1187D–12/01
ATtiny15L
Timer/Counter1 Output
Compare RegisterB – OCR1B
Bit
7
6
5
4
3
2
1
0
$2D
MSB
LSB
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
1
1
1
1
1
1
1
1
OCR1B
The Output Compare Register1 (OCR1B) is an 8-bit read/write register. This register is
used in the PWM mode only, and it limits the top value to which the Timer/Counter1
keeps counting. After reaching OCR1B in PWM mode, the counter starts from $00.
Table 13. PWM Outputs when OCR1A = $00 or OCR1B
COM1A1
COM1A0
OCR1B
Output PWMn
1
0
$00
L
1
0
OCR1B
H
1
1
$00
H
1
1
OCR1B
L
In PWM mode, the Timer Overflow Flag (TOV1) is set as in normal Timer/Counter
mode. Timer Overflow Interrupt1 operates exactly as in normal Timer/Counter mode,
i.e., it is executed when TOV1 is set provided that Timer Overflow Interrupt and global
interrupts are enabled. This also applies to the Timer Output Compare A flag and
interrupt.
The frequency of the PWM will be Timer Clock Frequency divided by OCR1B value + 1.
Table 14. Timer/Counter1 Clock Prescale Select
Clock Selection
OCR1B
PWM Frequency
CK
159
10 kHz
PCK/8
159
20 kHz
PCK/4
213
30 kHz
PCK/4
159
40 kHz
PCK/2
255
50 kHz
PCK/2
213
60 kHz
PCK/2
181
70 kHz
PCK/2
159
80 kHz
PCK/2
141
90 kHz
PCK
255
100 kHz
PCK
231
110 kHz
PCK
213
120 kHz
PCK
195
130 kHz
PCK
181
140 kHz
PCK
169
150 kHz
33
1187D–12/01
The Watchdog Timer
The Watchdog Timer is clocked from a separate On-chip Oscillator that runs at 1 MHz.
This is the typical value at VCC = 5V. See “Typical Characteristics” on page 66 for typical
values at other VCC levels. By controlling the Watchdog Timer prescaler, the Watchdog
Reset interval can be adjusted from 16 to 2048 ms, as shown in Table 15. The WDR
(Watchdog Reset) instruction resets the Watchdog Timer. Eight different clock cycle
periods can be selected to determine the reset period. If the reset period expires without
another Watchdog Reset, the ATtiny15L resets and executes from the reset vector. For
timing details on the Watchdog Reset, refer to page 17.
To prevent unintentional disabling of the Watchdog, a special turn-off sequence must be
followed when the Watchdog is disabled. Refer to the description of the Watchdog Timer
Control Register for details.
Figure 23. Watchdog Timer
Oscillator
1 MHz at Vcc = 5V
350 KHz at Vcc = 3V
WATCHDOG
PRESCALER
WATCHDOG
RESET
WDP0
WDP1
WDP2
WDE
MCU RESET
The Watchdog Timer Control
Register – WDTCR
Bit
7
6
5
4
3
2
1
0
$21
–
–
–
WDTOE
WDE
WDP2
WDP1
WDP0
Read/Write
R
R
R
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
WDTCR
• Bits 7..5 – Res: Reserved Bits
These bits are reserved bits in the ATtiny15L and will always read as zero.
• Bit 4 – WDTOE: Watchdog Turn-off Enable
This bit must be set (one) when the WDE bit is cleared. Otherwise, the Watchdog will
not be disabled. Once set, hardware will clear this bit to zero after four clock cycles.
Refer to the description of the WDE bit for a Watchdog disable procedure.
• Bit 3 – WDE: Watchdog Enable
When the WDE is set (one), the Watchdog Timer is enabled and if the WDE is cleared
(zero), the Watchdog Timer function is disabled. WDE can be cleared only when the
WDTOE bit is set (one). To disable an enabled Watchdog Timer, the following procedure must be followed:
1. In the same operation, write a logical “1” to WDTOE and WDE. A logical “1” must
be written to WDE even though it is set to one before the disable operation starts.
2. Within the next four clock cycles, write a logical “0” to WDE. This disables the
Watchdog.
34
ATtiny15L
1187D–12/01
ATtiny15L
• Bits 2..0 – WDP2, WDP1, WDP0: Watchdog Timer Prescaler Bits 2, 1, and 0
The WDP2, WDP1 and WDP0 bits determine the Watchdog Timer prescaling when the
Watchdog Timer is enabled. The different prescaling values and their corresponding
time-out periods are shown in Table 15.
Table 15. Watchdog Timer Prescale Select
WDP2
WDP1
WDP0
Time-out Period
0
0
0
16K cycles
0
0
1
32K cycles
0
1
0
64K cycles
0
1
1
128K cycles
1
0
0
256K cycles
1
0
1
512K cycles
1
1
0
1024K cycles
1
1
1
2048K cycles
35
1187D–12/01
EEPROM Read/Write
Access
The EEPROM access registers are accessible in the I/O space.
The write access time is in the range of 4.6 - 8.2 ms, depending on the frequency of the
calibrated RC oscillator. See Table 16 for details. A self-timing function however, lets the
user software detect when the next byte can be written. If the user code contains code
that writes the EEPROM, some precautions must be taken. In heavily filtered power
supplies, VCC is likely to rise or fall slowly on Power-up/down. This causes the device for
some period of time to run at a voltage lower than specified as minimum for the clock
frequency used. CPU operation under these conditions is likely to cause the program
counter to perform unintentional jumps and eventually execute the EEPROM write code.
To secure EEPROM integrity, the user is advised to use an external under-voltage reset
circuit in this case.
In order to prevent unintentional EEPROM writes, a two-state write procedure must be
followed. Refer to the description of the EEPROM Control Register for details of this.
When the EEPROM is read or written, the CPU is halted for two clock cycles before the
next instruction is executed.
The EEPROM Address
Register – EEAR
Bit
7
6
5
4
3
2
1
0
$1E
–
–
EEAR5
EEAR4
EEAR3
EEAR2
EEAR1
EEAR0
Read/Write
R
R
R/W
R/W
R/W
R/W
R/W
R/W
Initial vAlue
0
0
X
X
X
X
X
X
EEAR
• Bit 7, 6 – Res: Reserved Bits
These bits are reserved bits in the ATtiny15L and will always read as zero.
• Bit 5..0 – EEAR5..0: EEPROM Address
The EEPROM Address Register (EEAR) specifies the EEPROM address in the 64 bytes
EEPROM space. The EEPROM data bytes are addresses linearly between 0 and 63.
The initial value of EEAR is undefined. A proper value must be written before the
EEPROM may be accessed.
The EEPROM Data Register –
EEDR
Bit
7
6
5
4
3
2
1
0
$1D
MSB
LSB
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
EEDR
• Bit 7..0 – EEDR7..0: EEPROM Data
For the EEPROM write operation, the EEDR register contains the data to be written to
the EEPROM in the address given by the EEAR register. For the EEPROM read operation, the EEDR contains the data read out from the EEPROM at the address given by
EEAR.
The EEPROM Control Register
– EECR
Bit
7
6
5
4
3
2
1
0
$1C
–
–
–
–
EERIE
EEMWE
EEWE
EERE
Read/Write
R
R
R
R
R/W
R/W
R/W
R/W
Initial value
0
0
0
0
0
0
X
0
EECR
• Bit 7..4 – RES: Reserved Bits
These bits are reserved bits in the ATtiny15L and will always read as zero.
36
ATtiny15L
1187D–12/01
ATtiny15L
• Bit 3 – EERIE: EEPROM Ready Interrupt Enable
When the I-bits in SREG and EERIE are set (one), the EEPROM Ready Interrupt is
enabled. When cleared (zero), the interrupt is disabled. The EEPROM Ready Interrupt
generates a constant interrupt when EEWE is cleared (zero).
• Bit 2 – EEMWE: EEPROM Master Write Enable
The EEMWE bit determines whether setting EEWE to one causes the EEPROM to be
written. When EEMWE is set (one), setting EEWE will write data to the EEPROM at the
selected address. If EEMWE is zero, setting EEWE will have no effect. When EEMWE
has been set (one) by software, hardware clears the bit to zero after four clock cycles.
See the description of the EEWE bit for an EEPROM write procedure.
• Bit 1 – EEWE: EEPROM Write Enable
The EEPROM Write Enable Signal – EEWE – is the write strobe to the EEPROM. When
address and data are correctly set up, the EEWE bit must be set to write the value in to
the EEPROM. The EEMWE bit must be set when the logical “1” is written to EEWE, otherwise no EEPROM write takes place. The following procedure should be followed
when writing the EEPROM (the order of steps 2 and 3 is not essential):
1. Wait until EEWE becomes zero.
2. Write new EEPROM address to EEAR (optional).
3. Write new EEPROM data to EEDR (optional).
4. Write a logical “1” to the EEMWE bit in EECR.
5. Within four clock cycles after setting EEMWE, write a logical “1” to EEWE.
Caution: An interrupt between step 4 and step 5 will make the write cycle fail, since the
EEPROM Master Write Enable will time-out. If an interrupt routine accessing the
EEPROM is interrupting another EEPROM access, the EEAR or EEDR register will be
modified, causing the interrupted EEPROM access to fail. It is recommended to have
the global interrupt flag cleared during the four last steps to avoid these problems.
When the write access time (typically 5.1 ms if the internal RC oscillator is calibrated to
1.6 MHz) has elapsed, the EEWE bit is cleared (zero) by hardware. The user software
can poll this bit and wait for a zero before writing the next byte. When EEWE has been
set, the CPU is halted for two cycles before the next instruction is executed.
• Bit 0 – EERE: EEPROM Read Enable
The EEPROM Read Enable Signal EERE is the read strobe to the EEPROM. When the
correct address is set up in the EEAR register, the EERE bit must be set. When the
EERE bit is cleared (zero) by hardware, requested data is found in the EEDR register.
The EEPROM read access takes one instruction and there is no need to poll the EERE
bit. When EERE has been set, the CPU is halted for four cycles before the next instruction is executed.
The user should poll the EEWE bit before starting the read operation. If a write operation
is in progress when new data or address is written to the EEPROM I/O registers, the
write operation will be interrupted and the result is undefined.
37
1187D–12/01
The calibrated oscillator is used to time EEPROM. In Table 16 the typical programming
time is listed for EEPROM access from the CPU.
Table 16. Typical EEPROM Programming Times
Parameter
EEPROM write
(from CPU)
Preventing EEPROM
Corruption
Number of Calibrated RC
Oscillator Cycles
Min Programming
Time
Max Programming
Time
8192
4.6 ms
8.2 ms
During periods of low VCC, the EEPROM data can be corrupted because the supply voltage is too low for the CPU and the EEPROM to operate properly. These issues are the
same as for board-level systems using the EEPROM and the same design solutions
should be applied.
An EEPROM data corruption can be caused by two situations when the voltage is too
low. First, a regular write sequence to the EEPROM requires a minimum voltage to
operate correctly. Second, the CPU itself can execute instructions incorrectly if the supply voltage for executing instructions is too low.
EEPROM data corruption can easily be avoided by following these design recommendations (one is sufficient):
1. Keep the AVR RESET active (low) during periods of insufficient power supply
voltage. This can be done by enabling the internal Brown-out Detector (BOD) if
the operating voltage matches the detection level. If not, an external low VCC
Reset Protection circuit can be applied.
2. Keep the AVR core in Power-down sleep mode during periods of low VCC. This
will prevent the CPU from attempting to decode and execute instructions, effectively protecting the EEPROM registers from unintentional writes.
3. Store constants in Flash memory if the ability to change memory contents from
software is not required. Flash memory cannot be updated by the CPU and will
not be subject to corruption.
38
ATtiny15L
1187D–12/01
ATtiny15L
The Analog
Comparator
The Analog Comparator compares the input values on the positive pin PB0 (AIN0) and
negative pin PB1 (AIN1). When the voltage on the positive pin PB0 (AIN0) is higher than
the voltage on the negative pin PB1 (AIN1), the Analog Comparator Output (ACO) is set
(one). The comparator’s output can trigger a separate interrupt, exclusive to the Analog
Comparator. The user can select interrupt triggering on comparator output rise, fall or
toggle. A block diagram of the Comparator and its surrounding logic is shown in Figure
24.
Figure 24. Analog Comparator Block Diagram
The Analog Comparator
Control and Status Register –
ACSR
Bit
7
6
5
4
3
2
1
0
$08
ACD
ACBG
ACO
ACI
ACIE
–
ACIS1
ACIS0
Read/Write
R/W
R/W
R
R/W
R/W
R
R/W
R/W
Initial Value
0
0
X
0
0
0
0
0
ACSR
• Bit 7 – ACD: Analog Comparator Disable
When this bit is set (one), the power to the Analog Comparator is switched off. This bit
can be set at any time to turn off the Analog Comparator. This will reduce power consumption in Active and Idle mode. When changing the ACD-bit, the Analog Comparator
Interrupt must be disabled by clearing the ACIE bit in ACSR. Otherwise an interrupt can
occur when the bit is changed.
• Bit 6 – ACBG: Analog Comparator Bandgap Select
When this bit is set, a fixed bandgap voltage of 1.22 ± 0.05V replaces the normal input
to the positive pin (AIN0) of the comparator. When this bit is cleared, the normal input
pin PB0 is applied to the positive pin of the comparator.
• Bit 5 – ACO: Analog Comparator Output
ACO is directly connected to the comparator output.
• Bit 4 – ACI: Analog Comparator Interrupt Flag
This bit is set (one) when a comparator output event triggers the interrupt mode defined
by ACI1 and ACI0. The Analog Comparator Interrupt routine is executed if the ACIE bit
is set (one) and the I-bit in SREG is set (one). ACI is cleared by hardware when executing the corresponding interrupt handling vector. Alternatively, ACI is cleared by writing a
logical “1” to the flag.
39
1187D–12/01
• Bit 3 – ACIE: Analog Comparator Interrupt Enable
When the ACIE bit is set (one) and the I-bit in the Status Register is set (one), the Analog Comparator Interrupt is activated. When cleared (zero), the interrupt is disabled.
• Bit 2 – Res: Reserved Bit
This bit is a reserved bit in the ATtiny15L and will always read as zero.
• Bits 1, 0 – ACIS1, ACIS0: Analog Comparator Interrupt Mode Select
These bits determine the comparator events that trigger the Analog Comparator Interrupt. The different settings are shown in Table 17.
Table 17. ACIS1/ACIS0 Settings(1)
ACIS1
ACIS0
0
0
Comparator Interrupt on Output Toggle
0
1
Reserved
1
0
Comparator Interrupt on Falling Output Edge
1
1
Comparator Interrupt on Rising Output Edge
Note:
40
Interrupt Mode
1. When changing the ACIS1/ACIS0 bits, The Analog Comparator Interrupt must be disabled by clearing its Interrupt Enable bit in the ACSR register. Otherwise an interrupt
can occur when the bits are changed.
ATtiny15L
1187D–12/01
ATtiny15L
The Analog-to-Digital
Converter, Analog
Multiplexer, and Gain
Stages
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
10-bit Resolution
±2 LSB Absolute Accuracy
0.5 LSB Integral Non-linearity
Optional Offset Cancellation
65 - 260 µs Conversion Time
Up to 15 kSPS
4 Multiplexed Single-ended Input Channels
1 Differential Input Channel with Optional Gain of 20x
2.56V Internal Voltage Reference
0 - 2.56V Differential Input Voltage Range
0 - VCC Single-ended Input Voltage Range
Optional Left Adjustment for ADC Result Readout
Free Running or Single Conversion Mode
Interrupt on ADC Conversion Complete
Sleep Mode Noise Canceler
The ATtiny15L features a 10-bit successive approximation ADC. The ADC is connected
to a 4-channel Analog Multiplexer that allows one differential voltage input and four single-ended voltage inputs constructed from the pins of Port B. The differential input (PB3,
PB4) is equipped with a programmable gain stage, providing amplification step of 26 dB
(20x) on the differential input voltage before the A/D conversion. The single-ended voltage inputs at PB2..PB5 refer to 0V (GND).
The ADC contains a Sample and Hold Amplifier that ensures that the input voltage to
the ADC is held at a constant level during conversion. A block diagram of the ADC is
shown in Figure 25.
An internal reference voltage of nominally 2.56V is provided On-chip and this reference
can optionally be externally decoupled at the AREF (PB0) pin by a capacitor for better
noise performance. Alternatively, VCC can be used as reference voltage for singleended channels. There is also an option to use an external voltage reference and turn
off the internal voltage reference. These options are selected using the REFS1..0 bits of
the ADMUX control register.
41
1187D–12/01
Figure 25. Analog-to-Digital Converter Block Schematic
ADC CONVERSION
COMPLETE IRQ
ADC[9:0]
ADPS1
0
ADC DATA REGISTER
(ADCH/ADCL)
ADPS0
ADPS2
ADIF
ADFR
ADEN
ADSC
MUX1
9
ADC CTRL. & STATUS
REGISTER (ADCSR)
MUX0
MUX2
ADLAR
REFS0
REFS1
ADC MULTIPLEXER
SELECT (ADMUX)
ADIE
ADIF
8-BIT DATA BUS
PRESCALER
VCC
AREF
GAIN SELECTION
CHANNEL SELECTION
MUX DECODER
INTERNAL
2.56 V
REFERENCE
ADC1
SAMPLE & HOLD
COMPARATOR
10-BIT DAC
+
SINGLE ENDED / DIFFERENTIAL SELECTION
ADC3
ADC2
CONVERSION LOGIC
POS.
INPUT
MUX
ADC0
+
GAIN
AMPLIFIER
-
NEG.
INPUT
MUX
Operation
The ADC converts an analog input voltage to a 10-bit digital value through successive
approximation. The minimum value represents GND and the maximum value represents
the selected reference voltage minus 1 LSB.
The voltage reference for the ADC may be selected by writing to the REFS1..0 bits in
ADMUX. VCC, the AREF pin, or an internal 2.56V reference may be selected as the
ADC voltage reference. Optionally, the 2.56V internal voltage reference may be decoupled by an external capacitor at the AREF pin to improve noise immunity.
The analog input channel and differential gain are selected by writing to the MUX2..0
bits in ADMUX. Any of the four ADC input pins ADC3..0 can be selected as singleended inputs to the ADC. ADC2 and ADC3 can be selected as positive and negative
input, respectively, to the differential gain amplifier.
If differential channels are selected, the differential gain stage amplifies the voltage difference between the selected input pair by the selected gain factor, 1x or 20x, according
to the setting of the MUX2..0 bits in ADMUX. This amplified value then becomes the
analog input to the ADC. If single-ended channels are used, the gain amplifier is
bypassed altogether.
If ADC2 is selected as both the positive and negative input to the differential gain amplifier (ADC2 - ADC2), the remaining offset in the gain stage and conversion circuitry can
be measured directly as the result of the conversion. This figure can be subtracted from
subsequent conversions with the same gain setting to reduce offset error to below 1
LSB.
The ADC can operate in two modes – Single Conversion and Free Running. In Single
Conversion mode, each conversion will have to be initiated by the user. In Free Running
42
ATtiny15L
1187D–12/01
ATtiny15L
mode, the ADC is constantly sampling and updating the ADC Data Register. The ADFR
bit in ADCSR selects between the two available modes.
The ADC is enabled by setting the ADC Enable bit, ADEN in ADCSR. Voltage reference
and input channel selections will not go into effect until ADEN is set. The ADC does not
consume power when ADEN is cleared, so it is recommended to switch off the ADC
before entering Power-saving sleep modes.
A conversion is started by writing a logical “1” to the ADC Start Conversion bit, ADSC.
This bit stays high as long as the conversion is in progress and will be set to zero by
hardware when the conversion is completed. If a different data channel is selected while
a conversion is in progress, the ADC will finish the current conversion before performing
the channel change.
The ADC generates a 10-bit result, which is presented in the ADC data registers, ADCH
and ADCL. By default, the result is presented right-adjusted, but can optionally be presented left-adjusted by setting the ADLAR bit in ADMUX.
If the result is left-adjusted and no more than 8-bit precision is required, it is sufficient to
read ADCH. Otherwise, ADCL must be read first, then ADCH, to ensure that the content
of the data registers belongs to the same conversion. Once ADCL is read, ADC access
to data registers is blocked. This means that if ADCL has been read, and a conversion
completes before ADCH is read, neither register is updated and the result from the conversion is lost. When ADCH is read, ADC access to the ADCH and ADCL registers is reenabled.
The ADC has its own interrupt, which can be triggered when a conversion completes.
When ADC access to the data registers is prohibited between reading of ADCH and
ADCL, the interrupt will trigger even if the result is lost.
Prescaling and
Conversion Timing
Figure 26. ADC Prescaler
ADEN
Reset
7-BIT ADC PRESCALER
CK/64
CK/128
CK/32
CK/16
CK/8
CK/4
CK/2
CK
ADPS0
ADPS1
ADPS2
ADC CLOCK SOURCE
The successive approximation circuitry requires an input clock frequency between
50 kHz and 200 kHz. Using a higher input frequency will affect the conversion accuracy,
see “ADC Characteristics” on page 50. The ADC module contains a prescaler, which
divides the system clock to an acceptable ADC clock frequency.
The ADPSn bits in ADCSR are used to generate a proper ADC clock input frequency
from any CK frequency above 100 kHz. The prescaler starts counting from the moment
43
1187D–12/01
the ADC is switched on by setting the ADEN bit in ADCSR. The prescaler keeps running
for as long as the ADEN bit is set, and is continuously reset when ADEN is low.
When initiating a conversion by setting the ADSC bit in ADCSR, the conversion starts at
the following rising edge of the ADC clock cycle. If differential channels are selected, the
conversion will only start at every other rising edge of the ADC clock cycle after ADEN
was set.
A normal conversion takes 13 ADC clock cycles. In certain situations, the ADC needs
more clock cycles to perform initialization and minimize offset errors. These extended
conversions take 25 ADC clock cycles and occur as the first conversion after one of the
following events:
•
the ADC is switched on (ADEN in ADCSR is set)
•
the voltage reference source is changed (the REFS1..0 bits in ADMUX change
value)
•
a differential channel is selected (MUX2 in ADMUX is “1”). Note that subsequent
conversions on the same channel are not extended conversions.
The actual sample-and-hold takes place 1.5 ADC clock cycles after the start of a normal
conversion and 13.5 ADC clock cycles after the start of an extended conversion. When
a conversion is complete, the result is written to the ADC data registers, and ADIF is set.
In Single Conversion mode, ADSC is cleared simultaneously. The software may then
set ADSC again, and a new conversion will be initiated on the first rising ADC clock
edge. In Free Running mode, a new conversion will be started immediately after the
conversion completes while ADSC remains high. Using Free Running mode and an
ADC clock frequency of 200 kHz gives the lowest conversion time, 65 µs, equivalent to
15 kSPS. For a summary of conversion times, see Table 18.
Figure 27. ADC Timing Diagram, First Conversion (Single Conversion Mode)
Next
Conversion
Extended Conversion
Cycle Number
1
2
12
13
14
15
16
17
18
19
20
21
22
23
24
25
1
2
3
ADC Clock
ADEN
ADSC
ADIF
Sign and MSB of Result
ADCH
LSB of Result
ADCL
MUX and REFS
Update
44
Sample & Hold
Conversion
Complete
MUX and REFS
Update
ATtiny15L
1187D–12/01
ATtiny15L
Figure 28. ADC Timing Diagram, Single Conversion
Next
Conversion
Extended Conversion
Cycle Number
1
2
13
12
14
15
16
17
18
19
20
21
22
23
24
25
1
2
3
ADC Clock
ADEN
ADSC
ADIF
Sign and MSB of Result
ADCH
LSB of Result
ADCL
MUX and REFS
Update
Conversion
Complete
Sample & Hold
MUX and REFS
Update
Figure 29. ADC Timing Diagram, Free Running Conversion
One Conversion
Cycle Number
11
12
Next Conversion
13
1
2
3
4
ADC Clock
ADSC
ADIF
ADCH
Sign and MSB of Result
ADCL
LSB of Result
Sample & Hold
Conversion
Complete
MUX and REFS
Update
Table 18. ADC Conversion Time
Sample & Hold
(Cycles from Start of Conversion)
Conversion
Time (Cycles)
Conversion
Time (µs)
Extended Conversion
13.5
25.0
125 - 500
Normal Conversions
1.5
13.0
65 - 260
Condition
45
1187D–12/01
ADC Noise Canceler
Function
The ADC features a noise canceler that enables conversion during ADC Noise Reduction mode (see “Sleep Modes” on page 23) to reduce noise induced from the CPU core
and other I/O peripherals. If other I/O peripherals must be active during conversion, this
mode works equivalently for Idle mode. To make use of this feature, the following procedure should be used:
1. Make sure that the ADC is enabled and is not busy converting. Single Conversion mode must be selected and the ADC conversion complete interrupt must be
enabled.
ADEN = 1
ADSC = 0
ADFR = 0
ADIE = 1
2. Enter ADC Noise Reduction mode (or Idle mode). The ADC will start a conversion once the CPU has been halted.
3. If no other interrupts occur before the ADC conversion completes, the ADC interrupt will wake up the MCU and execute the ADC conversion complete interrupt
routine.
The ADC Multiplexer Selection
Register – ADMUX
Bit
7
6
5
4
3
2
1
0
$07
REFS1
REFS0
ADLAR
–
–
MUX2
MUX1
MUX0
Read/Write
R/W
R/W
R/W
R
R
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
ADMUX
• Bits 7..6 – REFS1..REFS0: Reference Selection Bits
These bits select the voltage reference for the ADC, as shown in Table 19. If these bits
are changed during a conversion, the change will not go into effect until this conversion
is complete (ADIF in ADCSR is set). Whenever these bits are changed, the next
conversion will take 25 ADC clock cycles. If active channels are used, using AVCC or an
external AREF higher than (AVCC - 1V) is not recommended, as this will affect ADC
accuracy. The internal voltage reference options may not be used if an external
reference voltage is being applied to the AREF pin.
Table 19. Voltage Reference Selections for ADC
REFS1
REFS0
Voltage Reference Selection
0
0
VCC used as analog reference, disconnected from PB0 (AREF).
0
1
External Voltage Reference at PB0 (AREF) pin, Internal Voltage
Reference turned off.
1
0
Internal Voltage Reference without external bypass capacitor,
disconnected from PB0 (AREF).
1
1
Internal Voltage Reference with external bypass capacitor at PB0 (AREF)
pin.
• Bit 5 – ADLAR: ADC Left Adjust Result
The ADLAR bit affects the presentation of the ADC conversion result in the ADC Data
Register. If ADLAR is cleared, the result is right-adjusted. If ADLAR is set, the result is
left-adjusted. Changing the ADLAR bit will affect the ADC Data Register immediately,
regardless of any ongoing conversions. For a complete description of this bit, see “The
ADC Data Register – ADCL and ADCH” on page 48.
46
ATtiny15L
1187D–12/01
ATtiny15L
• Bits 4..3 – Res: Reserved Bits
These bits are reserved bits in the ATtiny15L and always read as zero.
• Bits 2..0 – MUX2..MUX0: Analog Channel and Gain Selection Bits 2..0
The value of these bits selects which analog input is connected to the ADC. In case of
differential input (PB3 - PB4), gain selection is also made with these bits. Selecting PB3
as both inputs to the differential gain stage enables offset measurements. Refer to Table
20 for details. If these bits are changed during a conversion, the change will not go into
effect until this conversion is complete (ADIF in ADCSR is set).
Table 20. Input Channel and Gain Selections
MUX2..0
Single-ended
Input
000
ADC0 (PB5)
001
ADC1 (PB2)
010
ADC2 (PB3)
011
ADC3 (PB4)
Positive
Differential Input
Negative
Differential Input
Gain
N/A
(1)
100
ADC2 (PB3)
ADC2 (PB3)
1x
ADC2 (PB3)
ADC2 (PB3)
20x
110
ADC2 (PB3)
ADC3 (PB4)
1x
111
ADC2 (PB3)
ADC3 (PB4)
20x
(1)
101
N/A
Note:
The ADC Control and Status
Register – ADCSR
1. For offset calibration only. See “Operation” on page 42.
Bit
7
6
5
4
3
2
1
0
$06
ADEN
ADSC
ADFR
ADIF
ADIE
ADPS2
ADPS1
ADPS0
Read/Write
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
ADCSR
• Bit 7 – ADEN: ADC Enable
Writing a logical “1” to this bit enables the ADC. By clearing this bit to zero, the ADC is
turned off. Turning the ADC off while a conversion is in progress will terminate this
conversion.
• Bit 6 – ADSC: ADC Start Conversion
In Single Conversion mode, a logical “1” must be written to this bit to start each conversion. In Free Running mode, a logical “1” must be written to this bit to start the first
conversion.
When the conversion completes, ADSC returns to zero in Single Conversion mode and
stays high in Free Running mode.
Writing a “0” to this bit has no effect.
• Bit 5 – ADFR: ADC Free Running Select
When this bit is set (one), the ADC operates in Free Running mode. In this mode, the
ADC samples and updates the data registers continuously. Clearing this bit (zero) will
terminate Free Running mode. If active channels are used (MUX2 in ADMUX set), the
channel must be selected before entering Free Running mode. Selecting an active
channel after entering Free Running mode may result in undefined operation from the
ADC.
47
1187D–12/01
• Bit 4 – ADIF: ADC Interrupt Flag
This bit is set (one) when an ADC conversion completes and the data registers are
updated. The ADC Conversion Complete Interrupt is executed if the ADIE bit and the Ibit in SREG are set (one). ADIF is cleared by hardware when executing the corresponding interrupt handling vector. Alternatively, ADIF is cleared by writing a logical “1” to the
flag. Beware that if doing a read-modify-write on ADCSR, a pending interrupt can be disabled. This also applies if the SBI and CBI instructions are used.
• Bit 3 – ADIE: ADC Interrupt Enable
When this bit is set (one) and the I-bit in SREG is set (one), the ADC Conversion Complete Interrupt is activated.
• Bits 2..0 – ADPS2..ADPS0: ADC Prescaler Select Bits
These bits determine the division factor between the CK frequency and the input clock
to the ADC. See Table 21.
Table 21. ADC Prescaler Selections
ADPS2
ADPS1
ADPS0
Division Factor
0
0
0
2
0
0
1
2
0
1
0
4
0
1
1
8
1
0
0
16
1
0
1
32
1
1
0
64
1
1
1
128
The ADC Data Register –
ADCL and ADCH
ADLAR = 0
Bit
15
14
13
12
11
10
9
8
$05
–
–
–
–
–
–
ADC9
ADC8
ADCH
$04
ADC7
ADC6
ADC5
ADC4
ADC3
ADC2
ADC1
ADC0
ADCL
7
6
5
4
3
2
1
0
Read/Write
Initial Value
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ADLAR = 1
Bit
15
14
13
12
11
10
9
8
$05
ADC9
ADC8
ADC7
ADC6
ADC5
ADC4
ADC3
ADC2
ADCH
$04
ADC1
ADC0
–
–
–
–
–
–
ADCL
7
6
5
4
3
2
1
0
Read/Write
Initial Value
48
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ATtiny15L
1187D–12/01
ATtiny15L
When an ADC conversion is complete, the result is found in these two registers. When
ADCL is read, the ADC Data Register is not updated until ADCH is read. If the result is
left adjusted and no more than 8-bit precision is required, it is sufficient to read ADCH.
Otherwise, ADCL must be read first, then ADCH. The ADLAR bit in ADMUX affects the
way the result is read from the registers. If ADLAR is set, the result is left-adjusted. If
ADLAR is cleared (default), the result is right-adjusted.
• ADC9..0: ADC Conversion Result
These bits represent the result from the conversion. For the differential channel, this is
the value after gain adjustment, as indicated in Table 20 on page 47. For single-ended
conversion, or if ADLAR or SIGN is zero, $000 represents ground and $3FF represents
the selected reference voltage minus one LSB.
Scanning Multiple Channels
Since change of analog channel always is delayed until a conversion is finished, the
Free Running mode can be used to scan multiple channels without interrupting the converter. Typically, the ADC Conversion Complete Interrupt will be used to perform the
channel shift. However, the user should take the following fact into consideration:
The interrupt triggers once the result is ready to be read. In Free Running mode, the
next conversion will start immediately when the interrupt triggers. If ADMUX is
changed after the interrupt triggers, the next conversion has already started, and the
old setting is used.
ADC Noise-canceling
Techniques
Digital circuitry inside and outside the ATtiny15L generates EMI, which might affect the
accuracy of analog measurements. If conversion accuracy is critical, the noise level can
be reduced by applying the following techniques:
1. The analog part of the ATtiny15L and all analog components in the application
should have a separate analog ground plane on the PCB. This ground plane is
connected to the digital ground plane via a single point on the PCB.
2. Keep analog signal paths as short as possible. Make sure analog tracks run over
the analog ground plane, and keep them well away from high-speed switching
digital tracks.
3. Use the ADC noise canceler function to reduce induced noise from the CPU.
4. If some Port B pins are used as digital outputs, it is essential that these do not
switch while a conversion is in progress.
49
1187D–12/01
ADC Characteristics
Symbol
Parameter
Condition
Typ(1)
Max(1)
Units
Single-ended Conversion
10.0
Bits
Differential Conversion
Gain = 1x or 20x
8.0
Bits
Single-ended Conversion
VREF = 4V
ADC Clock = 200 kHz
1.0
Single-ended Conversion
VREF = 4V
ADC Clock = 1 MHz
4.0
LSB
Single-ended Conversion
VREF = 4V
ADC Clock = 2 MHz
16.0
LSB
Integral Non-linearity
VREF > 2V
0.5
LSB
Differential Non-linearity
VREF > 2V
0.5
LSB
Zero Error (Offset)
VREF > 2V
1.0
LSB
Conversion Time
Free Running Conversion
Resolution
Absolute Accuracy
2.0
LSB
65.0
260.0
µs
50.0
200.0
kHz
Single-ended Conversion
2.0
VCC
V
Differential Conversion
2.0
VCC - 0.2
V
Clock Frequency
VREF
Reference Voltage
VINT
Internal Voltage Reference
2.4
2.56
2.7
V
RREF
Reference Input Resistance
6.0
10.0
13.0
kΩ
RAIN
Analog Input Resistance
Note:
50
Min(1)
100.0
MΩ
1. Values are guidelines only. Actual values are TBD.
ATtiny15L
1187D–12/01
ATtiny15L
I/O Port B
All AVR ports have true read-modify-write functionality when used as general digital I/O
ports. This means that the direction of one port pin can be changed without unintentionally changing the direction of any other pin with the SBI and CBI instructions. The same
applies for changing drive value (if configured as output) or enabling/disabling of pull-up
resistors (if configured as input).
Port B is a 6-bit bi-directional I/O port.
Three data memory address locations are allocated for Port B, one each for the Data
Register – PORTB, $18, Data Direction Register – DDRB, $17, and the Port B Input
Pins – PINB, $16. The Port B Input Pins address is read-only, while the Data Register
and the Data Direction Register are read/write.
Ports PB5..0 have special functions as described in the section “Pin Descriptions” on
page 4. If PB5 is not configured as external reset, it is input with no pull-up or as an
open-drain output. All I/O pins have individually selectable pull-ups, which can be overridden with pull-up disable.
The Port B output buffers on PB0 to PB4 can sink 20 mA and thus drive LED displays
directly. PB5 can sink 12 mA. When pins PB0 to PB4 are used as inputs and are externally pulled low, they will source current (IIL) if the internal pull-ups are activated.
Alternative Functions of
Port B
In ATtiny15L four Port B pins – PB2, PB3, PB4, and PB5 – have alternative functions as
inputs for the ADC. If some Port B pins are configured as outputs, it is essential that
these do not switch when a conversion is in progress. This might corrupt the result of the
conversion. During Power-down mode and ADC Noise Reduction mode, the Schmitt
triggers of the digital inputs are disconnected on these pins. This allows an analog input
voltage close to VCC/2 to be present during Power-down without causing excessive
power consumption. The Port B pins with alternate functions are shown in Table 1 on
page 4.
When the pins PB4..0 are used for the alternate function, the DDRB and PORTB registers have to be set according to the alternate function description. When PB5 is used as
external reset pin, the values in the corresponding DDRB and PORTB bit are ignored.
The Port B Data Register –
PORTB
The Port B Data Direction
Register – DDRB
The Port B Input Pins Address
– PINB
Bit
7
6
5
4
3
2
1
0
$18
–
–
–
PORTB4
PORTB3
PORTB2
PORTB1
PORTB0
Read/Write
R
R
R
R/W
R/WS
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
Bit
7
6
5
4
3
2
1
0
$17
–
–
DDB5
DDB4
DDB3
DDB2
DDB1
DDB0
Read/Write
R
R
R/W
R/W
R/W
R/W
R/W
R/W
Initial Value
0
0
0
0
0
0
0
0
Bit
7
6
5
4
3
2
1
0
$16
–
–
PINB5
PINB4
PINB3
PINB2
PINB1
PINB0
Read/Write
R
R
R
R
R
R
R
R
Initial Value
0
0
N/A
N/A
N/A
N/A
N/A
N/A
PORTB
DDRB
PINB
The Port B Input Pins address (PINB) is not a register, and this address enables access
to the physical value on each Port B pin. When reading PORTB, the PORTB Data Latch
is read, and when reading PINB, the logical values present on the pins are read.
51
1187D–12/01
PORT B as General Digital I/O
The lower five pins in Port B are equal when used as digital I/O pins.
PBn, general I/O pin: The DDBn bit in the DDRB register selects the direction of this pin.
If DDBn is set (one), PBn is configured as an output pin. If DDBn is cleared (zero), PBn
is configured as an input pin. If PORTBn is set (one) when the pin is configured as an
input pin, the MOS pull-up resistor is activated. To switch the pull-up resistor off, the
PORTBn has to be cleared (zero) or the pin has to be configured as an output pin. Pullups for all ports can be disabled also by setting PUD-bit in the MCUCR register.
Table 22. DDBn Effects on Port B Pins(1)
DDBn
PORTBn
I/O
Pull-up
0
0
Input
No
Tri-state (High-Z)
0
1
Input
No
PUD bit in the MCUCR register is set.
0
1
Input
Yes
PBn will source current if ext. pulled low.
PUD bit in the MCUCR register is cleared.
1
0
Output
No
Push-pull Zero Output
1
1
Output
No
Push-pull One Output
Note:
Comment
1. n: 4,3…0, pin number.
On ATtiny15L, PB5 is input or open-drain output. Because this pin is used for 12V programming, there is no ESD protection diode limiting the voltage on the pin to
VCC + 0.5V. Thus, special care should be taken to ensure that the voltage on this pin
does not rise above VCC + 1V during normal operation. This may cause the MCU to
reset or enter programming mode unintentionally.
All Port B pins are connected to a pin change detector that can trigger the pin change
interrupt. See “Pin Change Interrupt” on page 21 for details.
Alternate Functions of Port B
The alternate pin functions of Port B are:
• RESET – PORT B, Bit 5
When the RSTDISBL fuse is unprogrammed, this pin serves as External Reset. When
the RSTDISBL fuse is programmed, this pin is a general input pin or a open-drain output
pin. If DDB5 is cleared (zero), PB5 is configured as an input pin. If DDB5 is set (one),
the pin is a open-drain output.
• SCK/INT0/T0 – PORT B, Bit 2
In Serial Programming mode, this pin serves as the serial clock input, SCK.
In normal mode, this pin can serve as the external interrupt0 input. See the interrupt
description for details on how to enable this interrupt. Note that activity on this pin will
trigger the interrupt even if the pin is configured as an output.
In normal mode, this pin can serve as the external counter clock input. See the
Timer/Counter0 description for further details. If external Timer/Counter clocking is
selected, activity on this pin will clock the counter even if it is configured as an output.
• MISO/OC1A/AIN1 – PORT B, Bit 1
In Serial Programming mode, this pin serves as the serial data output, MISO.
In normal mode, this pin can serve as Timer/Counter1 output compare match output
(OC1A). See the Timer/Counter1 description for further details, and how to enable the
output. The OC1A pin is also the output pin for PWM mode timer function.
This pin also serves as the negative input of the On-chip Analog Comparator.
52
ATtiny15L
1187D–12/01
ATtiny15L
• MOSI/AIN0/AREF – PORT B, Bit 0
In Serial Programming mode, this pin serves as the serial data input, MOSI.
In normal mode, this pin also serves as the positive input of the On-chip Analog
Comparator.
In ATtiny15L, this pin can be chosen to be the reference voltage for the ADC. Refer to
the section “The Analog-to-Digital Converter, Analog Multiplexer, and Gain Stages” for
details.
53
1187D–12/01
Memory
Programming
Program and Data
Memory Lock Bits
The ATtiny15L MCU provides two Lock bits that can be left unprogrammed, “1”, or can
be programmed, “0”, to obtain the additional features listed in Table 23. The Lock bits
can only be erased with the Chip Erase command.
Table 23. Lock Bit Protection Modes
Memory Lock Bits
Fuse Bits
Mode
LB1
LB2
Protection Type
1
1
1
No memory lock features enabled.
2
0
1
Further programming of the Flash and EEPROM is disabled.
3
0
0
Same as mode 2, but verify is also disabled.
The ATtiny15L has six Fuse bits (BODLEVEL, BODEN, SPIEN, RSTDSBL, and
CKSEL1..0). All the Fuse bits are programmable in both High-voltage and Low-voltage
Serial Programming modes. Changing the Fuses does not have effect while in programming mode.
•
The BODLEVEL Fuse selects the Brown-out Detection level and changes the startup times. See “Brown-out Detection” on page 16. See Table 5 on page 14. Default
value is programmed “0”.
•
When the BODEN Fuse is programed “0”, the Brown-out Detector is enabled. See
“Brown-out Detection” on page 16. Default value is unprogrammed “1”.
•
When the SPIEN Fuse bit is programmed “0”, Low-voltage Serial Program and Data
Downloading is enabled. Default value is programmed “0”. Unprogramming this fuse
while in the Low-voltage Serial Programming mode will disable future In-System
downloading attempts.
•
When the RSTDISBL Fuse is programmed “0”, the External Reset function of pin
PB5 is disabled(1). Default value is unprogrammed “1”. Programming this fuse while
in the Low-voltage Serial Programming mode will disable future In-System
downloading attempts.
•
CKSEL1..0 Fuses: See Table 5 on page 14 for which combination of CKSEL1..0 to
use. Default value is “00”, 64 ms + 18 CK.
The status of the Fuse bits is not affected by Chip Erase.
Note:
Signature Bytes
1. If the RSTDISBL Fuse is programmed, then the programming hardware should apply
+12V to PB5 while the ATtiny15L is in Power-on Reset. If not, the part can fail to enter
programming mode caused by drive contention on PB0 and/or PB5.
All Atmel microcontrollers have a three-byte signature code that identifies the device.
The three bytes reside in a separate address space, and for the ATtiny15L they are:
1. $000 : $1E (indicates manufactured by Atmel)
2. $001 : $90 (indicates 1 Kb Flash memory)
3. $002 : $06 (indicates ATtiny15L device when $001 is $90)
54
ATtiny15L
1187D–12/01
ATtiny15L
Calibration Byte
The ATtiny15L has a one-byte calibration value for the internal RC Oscillator. This byte
resides in the high byte of address $000 in the signature address space. To make use of
this byte, it should be read from this location and written into the normal Flash Program
memory. At start-up, the user software must read this Flash location and write the value
to the OSCCAL register.
Programming the Flash
Atmel’s ATtiny15L offers 1K byte of In-System Reprogrammable Flash Program memory and 64 bytes of in-System Reprogrammable EEPROM Data memory.
The ATtiny15L is shipped with the On-chip Flash program and EEPROM data memory
arrays in the erased state (i.e., contents = $FF) and ready to be programmed.
This device supports a High-voltage (12V) Serial Programming mode and a Low-voltage
Serial Programming mode. The +12V is used for programming enable only, and no current of significance is drawn by this pin (less than 100 µA) . The Low-voltage Serial
Programming mode provides a convenient way to download program and data into the
ATtiny15L inside the user’s system.
The program and data memory arrays in the ATtiny15L are programmed byte-by-byte in
either programming mode. For the EEPROM, an auto-erase cycle is provided within the
self-timed write instruction in the Low-voltage Serial Programming mode.
During programming, the supply voltage must be in accordance with Table 24.
Table 24. Supply Voltage during Programming
Part
Low-voltage Serial Programming
High-voltage Serial Programming
2.7 - 5.5V
4.5 - 5.5V
ATtiny15L
High-voltage Serial
Programming
This section describes how to program and verify Flash program memory, EEPROM
data memory, Lock bits and Fuse bits in the ATtiny15L.
Figure 30. High-voltage Serial Programming
11.5 - 12.5V
4.5 - 5.5V
ATtiny15/L
PB5 (RESET)
SERIAL CLOCK INPUT
VCC
PB2
SERIAL DATA OUTPUT
PB1
SERIAL INSTR. INPUT
PB0
SERIAL DATA INPUT
PB3
GND
55
1187D–12/01
High-voltage Serial
Programming Algorithm
To program and verify the ATtiny15L in the High-voltage Serial Programming mode, the
following sequence is recommended (See instruction formats in Table 25):
1. Power-up sequence:
Apply 4.5 - 5.5V between VCC and GND. Set PB5 and PB0 to “0” and wait at
least 30 µs.
Set PB3 to “0”. Wait at least 100 ns.
Apply 12V to PB5 and wait at least 100 ns before changing PB0. Wait 8 µs
before giving any instructions.
2. The Flash array is programmed one byte at a time by supplying first the address,
then the low and high data byte. The write instruction is self-timed; wait until the
PB2 (RDY/BSY) pin goes high.
3. The EEPROM array is programmed one byte at a time by supplying first the
address, then the data byte. The write instruction is self-timed; wait until the PB2
(RDY/BSY) pin goes high.
4. Any memory location can be verified by using the Read instruction, which
returns the contents at the selected address at serial output PB2.
5. Power-off sequence:
Set PB3 to “0”.
Set PB5 to “0”.
Turn VCC power off.
When writing or reading serial data to the ATtiny15L, data is clocked on the 8th rising
edge of the 16 external clock pulses needed to generate the internal clock. See Figure
31, Figure 32, and Table 26 for an explanation.
Figure 31. High-voltage Serial Programming Waveforms
SERIAL DATA INPUT
PB0
MSB
SERIAL INSTR. INPUT
PB1
MSB
SERIAL DATA OUTPUT
PB2
56
LSB
MSB
0
INTERNAL CK
SERIAL CLOCK INPUT
PB3
LSB
LSB
1
2
3
4
5
6
7
8
9
10
16x
ATtiny15L
1187D–12/01
ATtiny15L
Table 25. High-voltage Serial Programming Instruction Set for ATtiny15L(1)
Instruction Format
Instruction
Instr.1
Instr.2
Instr.3
Instr.4
PB0
0_1000_0000_00
0_0000_0000_00
0_0000_0000_00
0_0000_0000_00
PB1
0_0100_1100_00
0_0110_0100_00
0_0110_1100_00
0_0100_1100_00
PB2
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
PB0
0_0001_0000_00
0_0000_000a_00
0_bbbb_bbbb_00
PB1
0_0100_1100_00
0_0001_1100_00
0_0000_1100_00
PB2
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
PB0
0_ i i i i_i i i i _00
0_0000_0000_00
0_0000_0000_00
PB1
0_0010_1100_00
0_0110_0100_00
0_0110_1100_00
PB2
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
0_0000_0000_00
PB0
0_ i i i i_i i i i _00
0_0000_0000_00
0_0000_0000_00
PB1
0_0011_1100_00
0_0111_0100_00
0_0111_1100_00
PB2
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
0_0000_0000_00
PB0
0_0000_0010_00
0_0000_000a_00
0_bbbb_bbbb_00
PB1
0_0100_1100_00
0_0001_1100_00
0_0000_1100_00
PB2
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
PB0
0_0000_0000_00
0_0000_0000_00
PB1
0_0110_1000_00
0_0110_1100_00
PB2
x_xxxx_xxxx_xx
o_oooo_ooox_xx
PB0
0_0000_0000_00
0_0000_0000_00
PB1
0_0111_1000_00
0_0110_1100_00
PB2
x_xxxx_xxxx_xx
o_oooo_ooox_xx
Write
EEPROM
Low Address
PB0
0_0001_0001_00
0_00bb_bbbb_00
PB1
0_0100_1100_00
0_0000_1100_00
PB2
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
Write
EEPROM
Byte
PB0
0_ i i i i_i i i i _00
0_0000_0000_00
0_0000_0000_00
PB1
0_0010_1100_00
0_0110_0100_00
0_0110_1100_00
PB2
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
0_0000_0000_00
Read
EEPROM
Low Address
PB0
0_0000_0011_00
0_00bb_bbbb_00
PB1
0_0100_1100_00
0_0000_1100_00
PB2
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
Read
EEPROM
Byte
PB0
0_0000_0000_00
0_0000_0000_00
PB1
0_0110_1000_00
0_0110_1100_00
PB2
x_xxxx_xxxx_xx
o_oooo_ooox_xx
PB0
0_0100_0000_00
0_8765_1143_00
0_0000_0000_00
0_0000_0000_00
PB1
0_0100_1100_00
0_0010_1100_00
0_0110_0100_00
0_0110_1100_00
PB2
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
PB0
0_0010_0000_00
0_0000_0210_00
0_0000_0000_00
0_0000_0000_00
PB1
0_0100_1100_00
0_0010_1100_00
0_0110_0100_00
0_0110_1100_00
PB2
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
0_0000_0000_00
PB0
PB1
PB2
0_0000_0100_00
0_0000_0000_00
0_0000_0000_00
0_0100_1100_00
0_0110_1000_00
0_0110_1100_00
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
8_765x_x43x_xx
Chip Erase
Write Flash
High and Low
Address
Write Flash
Low Byte
Write Flash
High Byte
Read Flash
High and Low
Address
Read Flash
Low Byte
Read Flash
High Byte
Write Fuse
Bits
Write Lock
Bits
Read Fuse
Bits
Operation Remarks
Wait after Instr.3 until PB2
goes high for the Chip Erase
cycle to finish.
Repeat Instr.2 for a new 256
byte page. Repeat Instr.3 for
each new address.
Wait after Instr.3 until PB2
goes high. Repeat Instr.1,
Instr. 2 and Instr.3 for each
new address.
Wait after Instr.3 until PB2
goes high. Repeat Instr.1,
Instr. 2 and Instr.3 for each
new address.
Repeat Instr.2 and Instr.3 for
each new address.
Repeat Instr.1 and Instr.2 for
each new address.
Repeat Instr.1 and Instr.2 for
each new address.
Repeat Instr.2 for each new
address.
Wait after Instr.3 until PB2
goes high
Repeat Instr.2 for each new
address.
Repeat Instr.2 for each new
address
Wait after Instr.4 until PB2
goes high. Write 8 - 3 = “0” to
program the Fuse bit.
Wait after Instr.4 until PB2
goes high. Write 2, 1 = “0” to
program the Lock bit.
Reading 8 - 3 = “0” means the
Fuse bit is programmed.
57
1187D–12/01
Table 25. High-voltage Serial Programming Instruction Set for ATtiny15L(1) (Continued)
Instruction Format
Instruction
Instr.1
Instr.2
Instr.3
Instr.4
Read Lock
Bits
PB0
PB1
PB2
0_0000_0100_00
0_0000_0000_00
0_0000_0000_00
0_0100_1100_00
0_0111_1000_00
0_0111_1100_00
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_21xx_xx
Read
Signature
Bytes
PB0
PB1
PB2
0_0000_1000_00
0_0000_00bb_00
0_0000_0000_00
0_0000_0000_00
0_0100_1100_00
0_0000_1100_00
0_0110_1000_00
0_0110_1100_00
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
o_oooo_ooox_xx
PB0
0_0000_0000_00
0_0000_0000_00
0_0000_1000_00
0_0111_1000_00
0_0000_1100_00
0_0100_1100_00
PB1
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
PB2
1. a = address high bits
b = address low bits
i = data in
o = data out
x = don’t care
1 = Lock Bit1
2 = Lock Bit2
3 = CKSEL0 Fuse
4 = CKSEL1 Fuse
5 = RSTDSBL Fuse
6 = SPIEN Fuse
7 = BODEN Fuse
8 = BODLEVEL Fuse
The Lock bits can only be cleared by executing a Chip Erase.
Read
Calibration
Byte
Note:
58
Operation Remarks
Reading 2, 1 = “0” means the
Lock bit is programmed
Repeat Instr.2 - Instr.4 for
each signature byte address
0_0000_0000_00
0_0111_1100_00
o_oooo_ooox_xx
ATtiny15L
1187D–12/01
ATtiny15L
High-voltage Serial
Programming
Characteristics
Figure 32. High-voltage Serial Programming Timing
VALID
SDI (PB0), SII (PB1)
tSHIX t
SHSL
tIVSH
tSLSH
SCI (PB3)
1
2
7
8
9
10
15
16
SDO (PB2)
tSHOV
Internal CK
Table 26. High-voltage Serial Programming Characteristics, TA = 25 ° C ± 10%,
VCC = 5.0V ± 10% (unless otherwise noted)
Symbol
Low-voltage Serial
Downloading
Parameter
Min
Typ
tSHSL
SCI (PB3) Pulse Width High
25.0
ns
tSLSH
SCI (PB3) Pulse Width Low
25.0
ns
tIVSH
SDI (PB0), SII (PB1) Valid to SCI (PB3) High (8th
edge)
50.0
ns
tSHIX
SDI (PB0), SII (PB1) Hold after SCI (PB3) High (8th
edge)
50.0
ns
tSHOV
SCI (PB3) High (9th edge) to SDO (PB2) Valid
10.0
16.0
Max
32.0
Units
ns
Both the program and data memory arrays can be programmed using the SPI bus while
RESET is pulled to GND. The serial interface consists of pins SCK, MOSI (input) and
MISO (output). See Figure 33. After RESET is set low, the Programming Enable instruction needs to be executed first before program/erase instructions can be executed.
Figure 33. Serial Programming and Verify
2.7 - 5.5V
ATtiny15/L
GND
PB5 (RESET)
GND
VCC
PB2
SCK
PB1
MISO
PB0
MOSI
59
1187D–12/01
For the EEPROM, an auto-erase cycle is provided within the self-timed write instruction
and there is no need to first execute the Chip Erase instruction. The Chip Erase instruction turns the content of every memory location in both the program and EEPROM
arrays into $FF.
The program and EEPROM memory arrays have separate address spaces: $0000 to
$01FF for program memory and $000 to $03F for EEPROM memory.
The device is clocked from the internal clock at the uncalibrated minimum frequency
(0.8 - 1.6 MHz). The minimum low and high periods for the serial clock (SCK) input are
defined as follows:
Low: > 2 MCU clock cycles
High: > 2 MCU clock cycles
Low-voltage Serial
Programming Algorithm
When writing serial data to the ATtiny15L, data is clocked on the rising edge of SCK.
When reading data from the ATtiny15L, data is clocked on the falling edge of SCK. See
Figure 34, Figure 35, and Table 28 for timing details. To program and verify the
ATtiny15L in the Serial Programming mode, the following sequence is recommended
(See 4-byte instruction formats in Table 27):
1. Power-up sequence:
Apply power between VCC and GND while RESET and SCK are set to “0”. If the programmer cannot guarantee that SCK is held low during Power-up, RESET must be
given a positive pulse of at least two MCU cycles duration after SCK has been set to
“0”.
2. Wait for at least 20 ms and enable serial programming by sending the Programming Enable serial instruction to the MOSI (PB0) pin. Refer to the above section
for minimum low and high periods for the serial clock input SCK.
3. The serial programming instructions will not work if the communication is out of
synchronization. When in sync, the second byte ($53) will echo back when issuing the third byte of the Programming Enable instruction. Whether the echo is
correct or not, all four bytes of the instruction must be transmitted. If the $53 did
not echo back, give SCK a positive pulse and issue a new Programming Enable
instruction. If the $53 is not seen within 32 attempts, there is no functional device
connected.
4. If a Chip Erase is performed (must be done to erase the Flash), wait tWD_ERASE
after the instruction, give RESET a positive pulse, and start over from step 2.
See Table 29 on page 63 for tWD_ERASE value.
5. The Flash or EEPROM array is programmed one byte at a time by supplying the
address and data together with the appropriate write instruction. An EEPROM
memory location is first automatically erased before new data is written. Use
data polling to detect when the next byte in the Flash or EEPROM can be written.
If polling is not used, wait tWD_PROG_FL or tWD_PROG_EE, respectively, before transmitting the next instruction. See Table 30 on page 63 for the tWD_PROG_FL and
tWD_PROG_EE values. In an erased device, no $FFs in the data file(s) need to be
programmed.
6. Any memory location can be verified by using the Read instruction, which
returns the content at the selected address at the serial output MISO (PB1) pin.
7. At the end of the programming session, RESET can be set high to commence
normal operation.
8. Power-off sequence (if needed):
Set RESET to “1”.
Turn VCC power off.
60
ATtiny15L
1187D–12/01
ATtiny15L
Data Polling
When a byte is being programmed into the Flash or EEPROM, reading the address
location being programmed will give the value $FF. At the time the device is ready for a
new byte, the programmed value will read correctly. This is used to determine when the
next byte can be written. This will not work for the value $FF so when programming this
value, the user will have to wait for at least tWD_PROG_FL before programming the next
Flash byte, or tWD_PROG_EE before the next EEPROM byte. As a chip-erased device contains $FF in all locations, programming of addresses that are meant to contain $FF can
be skipped. This does not apply if the EEPROM is reprogrammed without chip-erasing
the device. In that case, data polling cannot be used for the value $FF and the user will
have to wait at least tWD_PROG_EE before programming the next byte. See Table 30 for
tWD_PROG_FL and tWD_PROG_EE values.
Figure 34. Low-voltage Serial Programming Waveforms
SERIAL DATA INPUT
PB0(MOSI)
MSB
LSB
SERIAL DATA OUTPUT
PB1(MISO)
MSB
LSB
SERIAL CLOCK INPUT
PB2(SCK)
61
1187D–12/01
Table 27. Low-voltage Serial Programming Instruction Set(1)
Instruction Format
Instruction
Byte 1
Byte 2
Byte 3
Byte4
Programming Enable
1010 1100
0101 0011
xxxx xxxx
xxxx xxxx
Enable Serial Programming while
RESET is low.
Chip Erase
1010 1100
100x xxxx
xxxx xxxx
xxxx xxxx
Chip Erase Flash and EEPROM
memory arrays.
Read Program Memory
0010 H000
xxxx xxxa
bbbb bbbb
oooo oooo
Read H (high or low) data o from
program memory at word address
a:b.
Write Program Memory
0100 H000
xxxx xxxa
bbbb bbbb
iiii iiii
Write H (high or low) data i to
Program memory at word address
a:b.
Read EEPROM
Memory
1010 0000
xxxx xxxx
xxbb bbbb
oooo oooo
Read data o from EEPROM memory
at address b.
Write EEPROM
Memory
1100 0000
xxxx xxxx
xxbb bbbb
iiii iiii
Write data i to EEPROM memory at
address b.
Write Lock Bits
1010 1100
1111 1211
xxxx xxxx
xxxx xxxx
Write Lock bits. Set bits 1,2 = “0” to
program Lock bits.
Read Lock Bits
0101 1000
xxxx xxxx
xxxx xxxx
xxxx x21x
Read Lock bits. “0” = programmed,
“1” = unprogrammed.
Read Signature Bytes
0011 0000
xxxx xxxx
0000 00bb
oooo oooo
Read signature byte o at address b.
Write Fuse Bits
1010 1100
101x xxxx
xxxx xxxx
8765 1143
Set bits 8 - 3 = “0” to program, “1” to
unprogram.
Read Fuse Bits
0101 0000
xxxx xxxx
xxxx xxxx
8765 xx43
Read Fuse bits. “0” = programmed,
“1” = unprogrammed.
xxxx xxxx
0000 0000
oooo oooo
Read Calibration Byte
0011 1000
Note:
1. a = address high bits
b = address low bits
H = 0 – low byte, 1 – high byte
o = data out
i = data in
x = don’t care
1 = Lock bit 1
2 = Lock bit 2
3 = CKSEL0 Fuse
4 = CKSEL1 Fuse
5 = RSTDISBL Fuse
6 = SPIEN Fuse
7 = BODEN Fuse
8 = BODLEVEL Fuse
62
Operation
ATtiny15L
1187D–12/01
ATtiny15L
Low-voltage Serial
Programming
Characteristics
Figure 35. Low-voltage Serial Programming Timing
MOSI
tOVSH
SCK
tSHOX
tSLSH
tSHSL
MISO
tSLIV
Table 28. Low-voltage Serial Programming Characteristics, TA = -40 ° C to 85 ° C,
VCC = 2.7 - 5.5V (Unless Otherwise Noted)
Symbol
Parameter
Min
Typ
1/tCLCL
RC Oscillator Frequency (VCC = 2.7 - 5.5V)
0.8
1.6
tCLCL
RC Oscillator Period (VCC = 2.7 - 5.5V)
tSHSL
SCK Pulse Width High
2.0 tCLCL
ns
tSLSH
SCK Pulse Width Low
2.0 tCLCL
ns
tOVSH
MOSI Setup to SCK High
tCLCL
ns
tSHOX
MOSI Hold after SCK High
2.0 tCLCL
ns
tSLIV
SCK Low to MISO Valid
625.0
10.0
16.0
Max
Units
MHz
1250.0
32.0
ns
ns
Table 29. Minimum Wait Delay after the Chip Erase Instruction
Symbol
Minimum Wait Delay
tWD_ERASE
8.2 ms
Table 30. Minimum Wait Delay after Writing a Flash or EEPROM Location
Symbol
Minimum Wait Delay
tWD_FLASH
4.1 ms
tWD_EEPROM
8.2 ms
63
1187D–12/01
Electrical Characteristics
Absolute Maximum Ratings
Operating Temperature.................................. -55°C to +125°C
*NOTICE:
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin Except RESET
with Respect to Ground ............................. -1.0V to VCC + 0.5V
Voltage on RESET with Respect to Ground ....-1.0V to +13.0V
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Maximum Operating Voltage ............................................ 6.0V
DC Current per I/O Pin ............................................... 40.0 mA
DC Current VCC and GND Pins................................ 100.0 mA
DC Characteristics
TA = -40°C to 85°C, VCC = 2.7V to 5.5V
Symbol
Parameter
Condition
Min
Typ
Max
Units
(1)
V
VIL
Input Low Voltage
Except (XTAL)
-0.5
0.3 VCC
VIL1
Input Low Voltage
XTAL
-0.5
0.1 VCC(1)
V
0.6 VCC
(2)
VCC + 0.5
V
0.7 VCC
(2)
VCC + 0.5
V
VCC + 0.5
V
VIH
VIH1
Input High Voltage
Input High Voltage
Except (XTAL, RESET)
XTAL
(2)
VIH2
Input High Voltage
RESET
VOL
Output Low Voltage(1)
Port B
IOL = 20 mA, VCC = 5V
IOL = 10 mA, VCC = 3V
0.6
0.5
V
V
VOL
Output Low Voltage
PB5
IOL = 12 mA, VCC = 5V
IOL = 6 mA, VCC = 3V
0.6
0.5
V
V
VOH
Output High Voltage(4)
Port B
IOH = -3 mA, VCC = 5V
IOH = -1.5 mA, VCC = 3V
IIL
Input Leakage Current
I/O Pin
VCC = 5.5V, Pin Low
(absolute value)
8.0
µA
IIH
Input Leakage Current
I/O Pin
VCC = 5.5V, Pin High
(absolute value)
8.0
µA
RI/O
I/O Pin Pull-up
122
kΩ
3.0
mA
1.0
1.2
mA
Power-down , VCC = 3V
WDT enabled
9.0
15.0
µA
Power-down(2), VCC = 3V
WDT disabled
<1.0
2.0
µA
0.85 VCC
4.3
2.3
V
V
35.0
Active, VCC = 3V
Idle, VCC = 3V
ICC
64
Power Supply Current
(2)
ATtiny15L
1187D–12/01
ATtiny15L
DC Characteristics (Continued)
TA = -40°C to 85°C, VCC = 2.7V to 5.5V
Symbol
Parameter
Condition
VACIO
Analog Comparator
Input Offset Voltage
VCC = 5V
VIN = VCC/2
IACLK
Analog Comparator
Input Leakage Current
VCC = 5V
VIN = VCC/2
TACID
Analog Comparator
Initialization Delay
VCC = 2.7V
VCC = 4.0V
Note:
Min
Typ
-50.0
750.0
500.0
Max
Units
40.0
mV
50.0
nA
ns
1. “Max” means the highest value where the pin is guaranteed to be read as low.
2. “Min” means the lowest value where the pin is guaranteed to be read as high.
3. Although each I/O port can sink more than the test conditions (20 mA at VCC = 5V, 10 mA at VCC = 3V) under steady state
conditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification.
Pins are not guaranteed to sink current greater than the listed test conditions.
4. Although each I/O port can source more than the test conditions (3 mA at VCC = 5V, 1.5 mA at VCC = 3V) under steady state
conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 100 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
5. Minimum VCC for Power-down is 1.5V (only with BOD disabled).
65
1187D–12/01
Typical
Characteristics
The following charts show typical behavior. These data are characterized but not tested.
All current consumption measurements are performed with all I/O pins configured as
inputs and with internal pull-ups enabled.
The current consumption is a function of several factors such as: Operating voltage,
operating frequency, loading of I/O pins, switching rate of I/O pins, code executed and
ambient temperature. The dominating factors are operating voltage and frequency.
The current drawn from capacitive loaded pins may be estimated (for one pin) as
CL•VCC•f where CL = load capacitance, VCC = operating voltage and f = average switching frequency of I/O pin.
The difference between current consumption in Power-down mode with Watchdog
Timer enabled and Power-down mode with Watchdog Timer disabled represents the differential current drawn by the Watchdog Timer.
Frequency Relative to Nominal Frequency at 25˚C and VCC = 5.0V
Figure 36. Calibrated Internal RC Oscillator Frequency vs. VCC
Relative Calibrated RC Oscillator Frequency vs. Operating Voltage
1.02
TA = 25
˚C
25˚C
TA = 45˚C
TA = 70˚C
1.00
TA = 85˚C
0.98
0.96
0.94
0.92
0.90
0.88
2
2.5
3
3.5
4
4.5
Operating Voltage (V)
5
5.5
6
Note: The nominal calibrated RC oscillator frequency is 1.6 MHz.
66
ATtiny15L
1187D–12/01
ATtiny15L
Figure 37. Analog Comparator Offset Voltage vs. Common Mode Voltage
ANALOG COMPARATOR OFFSET VOLTAGE vs.
COMMON MODE VOLTAGE
Vcc = 5V
18
16
TA = 25˚C
Offset Voltage (mV)
14
12
TA = 85˚C
10
8
6
4
2
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
Common Mode Voltage (V)
Note:
1. Analog Comparator offset voltage is measured as absolute offset.
Figure 38. Analog Comparator Offset Voltage vs. Common Mode Voltage
ANALOG COMPARATOR OFFSET VOLTAGE vs.
Vcc = 2.7V
COMMON MODE VOLTAGE
10
TA = 25˚C
Offset Voltage (mV)
8
6
TA = 85˚C
4
2
0
0
0.5
1
1.5
2
2.5
3
Common Mode Voltage (V)
67
1187D–12/01
Figure 39. Analog Comparator Input Leakage Current
ANALOG COMPARATOR INPUT LEAKAGE CURRENT
VCC = 6V
TA = 25˚C
60
50
(nA)
40
I
ACLK
30
20
10
0
-10
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
VIN (V)
Figure 40. Watchdog Oscillator Frequency vs. VCC
WATCHDOG OSCILLATOR FREQUENCY vs. Vcc
1600
1400
TA = 25˚C
1200
TA = 85˚C
F RC (KHz)
1000
800
600
400
200
0
1,5
2
2,5
3
3,5
4
4,5
5
5,5
6
Vcc (V)
Note:
68
1. Sink and source capabilities of I/O ports are measured on one pin at a time.
ATtiny15L
1187D–12/01
ATtiny15L
Figure 41. Pull-up Resistor Current vs. Input Voltage
PULL-UP RESISTOR CURRENT vs. INPUT VOLTAGE
Vcc = 5V
120
TA = 25˚C
100
TA = 85˚C
I
OP (µA)
80
60
40
20
0
0
0.5
1
1.5
2
2.5
VOP (V)
3
3.5
4
4.5
5
Figure 42. Pull-up Resistor Current vs. Input Voltage
PULL-UP RESISTOR CURRENT vs. INPUT VOLTAGE
Vcc = 2.7V
30
TA = 25˚C
25
TA = 85˚C
15
I
OP (µA)
20
10
5
0
0
0.5
1
1.5
2
2.5
3
VOP (V)
69
1187D–12/01
Figure 43. I/O Pin Sink Current vs. Output Voltage
I/O PIN SINK CURRENT vs. OUTPUT VOLTAGE
Vcc = 5V
70
TA = 25˚C
60
TA = 85˚C
50
30
I
OL (mA)
40
20
10
0
0
0.5
1
1.5
2
2.5
3
VOL (V)
Figure 44. I/O Pin Source Current vs. Output Voltage
I/O PIN SOURCE CURRENT vs. OUTPUT VOLTAGE
Vcc = 5V
20
TA = 25˚C
18
16
TA = 85˚C
14
I
OH (mA)
12
10
8
6
4
2
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
VOH (V)
70
ATtiny15L
1187D–12/01
ATtiny15L
Figure 45. I/O Pin Sink Current vs. Output Voltage
I/O PIN SINK CURRENT vs. OUTPUT VOLTAGE
Vcc = 2.7V
25
TA = 25˚C
20
TA = 85˚C
10
I
OL (mA)
15
5
0
0
0.5
1
1.5
2
VOL (V)
Figure 46. I/O Pin Source Current vs. Output Voltage
I/O PIN SOURCE CURRENT vs. OUTPUT VOLTAGE
Vcc = 2.7V
6
TA = 25˚C
5
TA = 85˚C
3
I
OH (mA)
4
2
1
0
0
0.5
1
1.5
2
2.5
3
VOH (V)
71
1187D–12/01
Figure 47. I/O Pin Input Threshold Voltage vs. VCC
I/O PIN INPUT THRESHOLD VOLTAGE vs. Vcc
TA = 25˚C
2.5
Threshold Voltage (V)
2
1.5
1
0.5
0
2.7
4.0
5.0
Vcc
Figure 48. I/O Pin Input Hysteresis vs. VCC
I/O PIN INPUT HYSTERESIS vs. Vcc
TA = 25˚C
0.18
0.16
Input hysteresis (V)
0.14
0.12
0.1
0.08
0.06
0.04
0.02
0
2.7
4.0
5.0
Vcc
72
ATtiny15L
1187D–12/01
ATtiny15L
ATtiny15L Register Summary
Address
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Page
$3F
SREG
I
T
H
S
V
N
Z
C
page 11
$3E
Reserved
$3C
Reserved
$3B
GIMSK
-
INT0
PCIE
-
-
-
-
-
page 19
$3A
GIFR
-
INTF0
PCIF
-
-
-
-
-
page 19
$39
TIMSK
-
OCIE1A
-
-
-
TOIE1
TOIE0
-
page 20
$38
TIFR
-
OCF1A
-
-
-
TOV1
TOV0
-
page 21
$37
Reserved
$36
Reserved
$35
MCUCR
-
PUD
SE
SM1
SM0
-
ISC01
ISC00
page 22
$34
MCUSR
-
-
-
-
WDRF
BORF
EXTRF
PORF
page 17
$33
TCCR0
-
-
-
-
-
CS02
CS01
CS00
$32
TCNT0
$31
OSCCAL
$30
TCCR1
$2F
TCNT1
Timer/Counter1 (8-Bit)
page 31
page 31
Timer/Counter0 (8-Bit)
Oscillator Calibration Register
CTC1
PWM1
COM1A1
COM1A0
CS13
page 24
CS12
$2E
OCR1A
Timer/Counter1 Output Compare Register A (8-Bit)
$2D
OCR1B
Timer/Counter1 Output Compare Register B (8-Bit)
$2C
SFIOR
$2B
Reserved
$2A
Reserved
$29
Reserved
$28
Reserved
$27
Reserved
$26
Reserved
$25
Reserved
$24
Reserved
$23
Reserved
$22
Reserved
$21
WDTCR
$20
Reserved
$1F
Reserved
$1E
EEAR
$1D
EEDR
$1C
EECR
$1B
Reserved
$1A
Reserved
$19
Reserved
$18
$17
-
FOC1A
PSR1
PSR0
page 26
-
-
-
WDTOE
WDE
WDP2
WDP1
WDP0
page 34
-
-
EEAR5
EEAR4
EEAR3
EEAR2
EEAR1
EEAR0
page 36
EEPROM Data Register (8-Bit)
-
$16
PINB
-
$15
Reserved
$14
Reserved
$13
Reserved
$12
Reserved
$11
Reserved
$10
Reserved
$0D
Reserved
$0C
Reserved
$0B
Reserved
$0A
Reserved
$09
Reserved
page 33
-
DDRB
Reserved
page 30
-
PORTB
Reserved
CS10
-
-
$0E
CS11
-
-
$0F
page 27
page 28
page 36
-
-
EERIE
EEMWE
EEWE
EERE
page 36
-
-
PORTB4
PORTB3
PORTB2
PORTB1
PORTB0
page 51
-
DDB5
DDB4
DDB3
DDB2
DDB1
DDB0
page 51
-
PINB5
PINB4
PINB3
PINB2
PINB1
PINB0
page 51
$08
ACSR
ACD
ACBG
ACO
ACI
ACIE
-
ACIS1
ACIS0
page 39
$07
ADMUX
REFS1
REFS0
ADLAR
-
-
MUX2
MUX1
MUX0
page 46
$06
ADCSR
ADEN
ADSC
ADFR
ADIF
ADIE
ADPS2
ADPS1
ADPS0
page 47
$05
ADCH
ADC Data Register High Byte
page 48
$04
ADCL
ADC Data Register Low Byte
page 48
…
Reserved
$00
Reserved
73
1187D–12/01
ATtiny15L Instruction Set Summary
Mnemonic
Operands
Description
Operation
Flags
# Clocks
ARITHMETIC AND LOGIC INSTRUCTIONS
ADD
Rd, Rr
Add Two Registers
Rd ← Rd + Rr
Z,C,N,V,H
ADC
Rd, Rr
Add with Carry Two Registers
Rd ← Rd + Rr + C
Z,C,N,V,H
1
SUB
Rd, Rr
Subtract Two Registers
Rd ← Rd - Rr
Z,C,N,V,H
1
SUBI
Rd, K
Subtract Constant from Register
Rd ← Rd - K
Z,C,N,V,H
1
SBC
Rd, Rr
Subtract with Carry Two Registers
Rd ← Rd - Rr - C
Z,C,N,V,H
1
SBCI
Rd, K
Subtract with Carry Constant from Reg.
Rd ← Rd - K - C
Z,C,N,V,H
1
AND
Rd, Rr
Logical AND Registers
Rd ← Rd • Rr
Z,N,V
1
ANDI
Rd, K
Logical AND Register and Constant
Rd ← Rd • K
Z,N,V
1
OR
Rd, Rr
Logical OR Registers
Rd ← Rd v Rr
Z,N,V
1
ORI
Rd, K
Logical OR Register and Constant
Rd ← Rd v K
Z,N,V
1
EOR
Rd, Rr
Exclusive OR Registers
Rd ← Rd⊕Rr
Z,N,V
1
COM
Rd
One’s Complement
Rd ← $FF - Rd
Z,C,N,V
1
NEG
Rd
Two’s Complement
Rd ← $00 - Rd
Z,C,N,V,H
1
SBR
Rd, K
Set Bit(s) in Register
Rd ← Rd v K
Z,N,V
1
1
1
CBR
Rd, K
Clear Bit(s) in Register
Rd ← Rd • (FFh - K)
Z,N,V
INC
Rd
Increment
Rd ← Rd + 1
Z,N,V
1
DEC
Rd
Decrement
Rd ← Rd - 1
Z,N,V
1
TST
Rd
Test for Zero or Minus
Rd ← Rd • Rd
Z,N,V
1
CLR
Rd
Clear Register
Rd ← Rd⊕Rd
Z,N,V
1
SER
Rd
Set Register
Rd ← $FF
None
1
BRANCH INSTRUCTIONS
RJMP
k
Relative Jump
PC ← PC + k + 1
None
2
RCALL
k
Relative Subroutine Call
PC ← PC + k + 1
None
3
4
RET
Subroutine Return
PC ← STACK
None
RETI
Interrupt Return
PC ← STACK
I
4
CPSE
Rd, Rr
Compare, Skip if Equal
if (Rd = Rr) PC ← PC + 2 or 3
None
CP
Rd, Rr
Compare
Rd - Rr
Z,N,V,C,H
CPC
Rd, Rr
Compare with Carry
Rd - Rr - C
Z,N,V,C,H
1
CPI
Rd, K
Compare Register with Immediate
Rd - K
Z,N,V,C,H
1
SBRC
Rr, b
Skip if Bit in Register Cleared
if (Rr(b) = 0) PC ← PC + 2 or 3
None
1/2
SBRS
Rr, b
Skip if Bit in Register is Set
if (Rr(b) = 1) PC ← PC + 2 or 3
None
1/2
1/2
1
SBIC
P, b
Skip if Bit in I/O Register Cleared
if (P(b) = 0) PC ← PC + 2 or 3
None
1/2
SBIS
P, b
Skip if Bit in I/O Register is Set
if (P(b) = 1) PC ← PC + 2 or 3
None
1/2
BRBS
s, k
Branch if Status Flag Set
if (SREG(s) = 1) then PC ← PC + k + 1
None
1/2
BRBC
s, k
Branch if Status Flag Cleared
if (SREG(s) = 0) then PC ← PC + k + 1
None
1/2
BREQ
k
Branch if Equal
if (Z = 1) then PC ← PC + k + 1
None
1/2
BRNE
k
Branch if Not Equal
if (Z = 0) then PC ← PC + k + 1
None
1/2
BRCS
k
Branch if Carry Set
if (C = 1) then PC ← PC + k + 1
None
1/2
BRCC
k
Branch if Carry Cleared
if (C = 0) then PC ← PC + k + 1
None
1/2
BRSH
k
Branch if Same or Higher
if (C = 0) then PC ← PC + k + 1
None
1/2
BRLO
k
Branch if Lower
if (C = 1) then PC ← PC + k + 1
None
1/2
BRMI
k
Branch if Minus
if (N = 1) then PC ← PC + k + 1
None
1/2
BRPL
k
Branch if Plus
if (N = 0) then PC ← PC + k + 1
None
1/2
BRGE
k
Branch if Greater or Equal, Signed
if (N ⊕ V= 0) then PC ← PC + k + 1
None
1/2
BRLT
k
Branch if Less Than Zero, Signed
if (N ⊕ V= 1) then PC ← PC + k + 1
None
1/2
BRHS
k
Branch if Half-carry Flag Set
if (H = 1) then PC ← PC + k + 1
None
1/2
BRHC
k
Branch if Half-carry Flag Cleared
if (H = 0) then PC ← PC + k + 1
None
1/2
BRTS
k
Branch if T-flag Set
if (T = 1) then PC ← PC + k + 1
None
1/2
BRTC
k
Branch if T-flag Cleared
if (T = 0) then PC ← PC + k + 1
None
1/2
BRVS
k
Branch if Overflow Flag is Set
if (V = 1) then PC ← PC + k + 1
None
1/2
BRVC
k
Branch if Overflow Flag is Cleared
if (V = 0) then PC ← PC + k + 1
None
1/2
BRIE
k
Branch if Interrupt Enabled
if (I = 1) then PC ← PC + k + 1
None
1/2
BRID
k
Branch if Interrupt Disabled
if (I = 0) then PC ← PC + k + 1
None
1/2
DATA TRANSFER INSTRUCTIONS
LD
Rd, Z
Load Register Indirect
Rd ← (Z)
None
2
ST
Z, Rr
Store Register Indirect
(Z) ← Rr
None
2
MOV
Rd, Rr
Move between Registers
Rd ← Rr
None
1
LDI
Rd, K
Load Immediate
Rd ← K
None
1
IN
Rd, P
In Port
Rd ← P
None
1
OUT
P, Rr
Out Port
P ← Rr
None
1
Load Program Memory
R0 ← (Z)
None
3
LPM
74
ATtiny15L
1187D–12/01
ATtiny15L
ATtiny15L Instruction Set Summary (Continued)
Mnemonic
Operands
Description
Operation
Flags
# Clocks
BIT AND BIT-TEST INSTRUCTIONS
SBI
P, b
Set Bit in I/O Register
I/O(P,b) ← 1
None
2
CBI
P, b
Clear Bit in I/O Register
I/O(P,b) ← 0
None
2
LSL
Rd
Logical Shift Left
Rd(n+1) ← Rd(n), Rd(0) ← 0
Z,C,N,V
1
LSR
Rd
Logical Shift Right
Rd(n) ← Rd(n+1), Rd(7) ← 0
Z,C,N,V
1
ROL
Rd
Rotate Left through Carry
Rd(0) ← C, Rd(n+1) ← Rd(n), C ← Rd(7)
Z,C,N,V
1
ROR
Rd
Rotate Right through Carry
Rd(7) ← C, Rd(n) ← Rd(n+1), C ← Rd(0)
Z,C,N,V
1
ASR
Rd
Arithmetic Shift Right
Rd(n) ← Rd(n+1), n = 0..6
Z,C,N,V
1
SWAP
Rd
Swap Nibbles
Rd(3..0) ← Rd(7..4), Rd(7..4) ← Rd(3..0)
None
1
BSET
s
Flag Set
SREG(s) ← 1
SREG(s)
1
1
BCLR
s
Flag Clear
SREG(s) ← 0
SREG(s)
BST
Rr, b
Bit Store from Register to T
T ← Rr(b)
T
1
BLD
Rd, b
Bit Load from T to Register
Rd(b) ← T
None
1
SEC
Set Carry
C←1
C
1
CLC
Clear Carry
C←0
C
1
SEN
Set Negative Flag
N←1
N
1
CLN
Clear Negative Flag
N←0
N
1
SEZ
Set Zero Flag
Z←1
Z
1
CLZ
Clear Zero Flag
Z←0
Z
1
SEI
Global Interrupt Enable
I←1
I
1
CLI
Global Interrupt Disable
I←0
I
1
SES
Set Signed Test Flag
S←1
S
1
CLS
Clear Signed Test Flag
S←0
S
1
SEV
Set Two’s Complement Overflow
V←1
V
1
CLV
Clear Two’s Complement Overflow
V←0
V
1
SET
Set T in SREG
T←1
T
1
CLT
Clear T in SREG
T←0
T
1
SEH
Set Half-carry Flag in SREG
H←1
H
1
CLH
Clear Half-carry Flag in SREG
H←0
H
1
NOP
No Operation
None
1
SLEEP
Sleep
(see specific descr. for Sleep function)
None
1
WDR
Watchdog Reset
(see specific descr. for WDR/timer)
None
1
75
1187D–12/01
Ordering Information
Power Supply
Speed (MHz)
Ordering Code
Package
Operation Range
2.7 - 5.5V
1.6
ATtiny15L-1PC
ATtiny15L-1SC
8P3
8S2
Commercial
(0°C to 70°C)
ATtiny15L-1PI
ATtiny15L-1SI
8P3
8S2
Industrial
(-40°C to 85°C)
Package Type
8P3
8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP)
8S2
8-lead, 0.200" Wide, Plastic Gull Wing Small Outline (EIAJ SOIC)
76
ATtiny15L
1187D–12/01
ATtiny15L
Packaging Information
8P3
8P3, 8-lead, Plastic Dual Inline
Package (PDIP), 0.300" Wide.
Dimensions in Millimeters and (Inches)*
JEDEC STANDARD MS-001 BA
10.16(0.400)
9.017(0.355)
PIN
1
7.11(0.280)
6.10(0.240)
.300 (7.62) REF
254(0.100) BSC
5.33(0.210) MAX
Seating Plane
3.81(0.150)
2.92(0.115)
1.78(0.070)
1.14(0.045)
0.381(0.015)MIN
0.559(0.022)
0.356(0.014)
4.95(0.195)
2.92(0.115)
8.26(0.325)
7.62(0.300)
0.356(0.014)
0.203(0.008)
1.524(0.060)
0.000(0.000)
10.90(0.430) MAX
*Controlling dimension: Inches
REV. A
04/11/2001
77
1187D–12/01
8S2
.020 (.508)
.012 (.305)
.213 (5.41)
.205 (5.21)
PIN 1
.330 (8.38)
.300 (7.62)
.050 (1.27) BSC
.212 (5.38)
.203 (5.16)
.080 (2.03)
.070 (1.78)
.013 (.330)
.004 (.102)
0
REF
8
.010 (.254)
.007 (.178)
.035 (.889)
.020 (.508)
78
ATtiny15L
1187D–12/01
Atmel Headquarters
Atmel Product Operations
Corporate Headquarters
Atmel Colorado Springs
2325 Orchard Parkway
San Jose, CA 95131
TEL (408) 441-0311
FAX (408) 487-2600
Europe
Atmel SarL
Route des Arsenaux 41
Casa Postale 80
CH-1705 Fribourg
Switzerland
TEL (41) 26-426-5555
FAX (41) 26-426-5500
Asia
Atmel Asia, Ltd.
Room 1219
Chinachem Golden Plaza
77 Mody Road Tsimhatsui
East Kowloon
Hong Kong
TEL (852) 2721-9778
FAX (852) 2722-1369
Japan
Atmel Japan K.K.
9F, Tonetsu Shinkawa Bldg.
1-24-8 Shinkawa
Chuo-ku, Tokyo 104-0033
Japan
TEL (81) 3-3523-3551
FAX (81) 3-3523-7581
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
TEL (719) 576-3300
FAX (719) 540-1759
Atmel Grenoble
Avenue de Rochepleine
BP 123
38521 Saint-Egreve Cedex, France
TEL (33) 4-7658-3000
FAX (33) 4-7658-3480
Atmel Heilbronn
Theresienstrasse 2
POB 3535
D-74025 Heilbronn, Germany
TEL (49) 71 31 67 25 94
FAX (49) 71 31 67 24 23
Atmel Nantes
La Chantrerie
BP 70602
44306 Nantes Cedex 3, France
TEL (33) 0 2 40 18 18 18
FAX (33) 0 2 40 18 19 60
Atmel Rousset
Zone Industrielle
13106 Rousset Cedex, France
TEL (33) 4-4253-6000
FAX (33) 4-4253-6001
Atmel Smart Card ICs
Scottish Enterprise Technology Park
East Kilbride, Scotland G75 0QR
TEL (44) 1355-357-000
FAX (44) 1355-242-743
e-mail
[email protected]
Web Site
http://www.atmel.com
© Atmel Corporation 2001.
Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty
which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors
which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does
not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted
by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical
components in life support devices or systems.
ATMEL ® and AVR ® are the registered trademarks of Atmel.
Other terms and product names may be the trademarks of others.
Printed on recycled paper.
1187D–12/01/0M