AWC6341 HELP CDMA Band Class 1 CDMA Power Amplifier Module TM Data Sheet - Rev 2.4 FEATURES • CDMA / EVDO Compliant •HELPTM technology • High Efficiency (RC-1 waveform): • 37 % @ POUT = +28.2 dBm • 33 % @ POUT = +17 dBm AWC6341 • Low Quiescent Current: 11 mA • Low Leakage Current in Shutdown Mode: <5 µA • Internal Voltage Regulator • Integrated “daisy chainable” directional coupler with CPLIN and CPLOUT port • Internal DC blocks on RF IN/OUT ports M45 Package 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module • Optimized for a 50 Ω System • 1.8 V Control Logic • RoHS Compliant Package, 260 oC MSL-3 APPLICATIONS • Band Class 1 and 14 CDMA/EVDO Wireless Devices PRODUCT DESCRIPTION The AWC6341 is a HELPTM product for CDMA devices operating in Band Class 1 and Band Class 14. This PA incorporates ANADIGICS’ HELPTM technology to deliver exceptional efficiency at low power levels and low quiescent current without the need for external voltage regulators or converters. The device is manufactured using advanced InGaP HBT technology offering state-of-the-art reliability, temperature stability, and ruggedness. Two selectable bias modes that optimize efficiency for different output power levels and a shutdown mode with low leakage current increase handset talk and standby time. A “daisy chainable” directional coupler is integrated in the module, thus eliminating the need of an external coupler. The self-contained 3 mm x 3 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency, and linearity in a 50 Ω system. GND at Slug (pad) VBATT 1 RFIN 2 GND 3 VMODE VEN 11/2012 10 VCC 9 RFOUT 8 CPLIN 4 7 GND 5 6 CPLOUT CPL Bias Control Voltage Regulation Figure 1: Block Diagram AWC6341 VBATT 1 10 RFIN 2 9 RFOUT GND 3 8 CPLIN VMODE 4 7 GND VEN 5 6 CPLOUT Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 VBATT Battery Voltage 2 RFIN RF Input 3 GND Ground 4 VMODE Mode Control Voltage 5 VEN 6 CPLOUT 7 GND Ground 8 CPLIN Coupler Input 9 RFOUT RF Output 10 VCC PA Enable Voltage Coupler Output Supply Voltage Data Sheet - Rev 2.4 11/2012 VCC AWC6341 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VCC) 0 +5 V Battery Voltage (VBATT) 0 +6 V Control Voltages (VMODE,VEN) 0 +3.5 V RF Input Power (PIN) - +10 dBm -40 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT Operating Frequency (f) 1850 - 1915 MHz Supply Voltage (VCC) +3.1 +3.4 +4.35 V POUT < +28.2 dBm Enable Voltage (VEN) +1.35 0 +1.8 - +3.1 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE) +1.35 0 +1.8 - +3.1 +0.5 V Low Bias Mode High Bias Mode CDMA Output Power HPM LPM 27.4 - 28.2 17.0 - dBm Case Temperature (TC) -30 - +90 °C COMMENTS CDMA2000, RC-1 The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1)For Operation at 3.1 V, POUT is derated by 0.8 dB. 3 Data Sheet - Rev 2.4 11/2012 AWC6341 Table 4: Electrical Specifications - CDMA Operation (CDMA2000, RC-1) (TC = +25 °C, VBATT = VCC = +3.4 V, VENABLE = +1.8 V, 50 Ω system) PARAMETER MIN TYP MAX UNIT 25 17 27.5 19.5 30.5 22 Adjacent Channel Power at +1.25 MHz offset Primary Channel BW - 1.23 MHz Adjacent Channel BW = 30 kHz - -50 -55 Adjacent Channel Power at +1.98 MHz Primary Channel BW=1.23 MHz Adjacent Channel BW=30 kHz - COMMENTS POUT VMODE dB POUT = +28.2 dBm POUT = +17 dBm 0V 1.8 V -46 -46 dBc POUT = +28.2 dBm POUT = +17 dBm 0V 1.8 V -56 -59 -53 -53 dBc POUT = +28.2 dBm POUT = +17 dBm 0V 1.8 V 33 29 37 33 - % POUT = +28.2 dBm POUT = +17 dBm 0V 1.8 V Quiescent Current (Icq) Low Bias Mode - 11 15 mA through VCC pin 1.8 V Mode Control Current - 0.08 0.15 mA through VMODE pin, VMODE = +1.8 V Enable Current - 0.04 0.1 mA through VEN pin, VEN = +1.8 V BATT Current - 3.5 5.5 mA through VBATT pin, VMODE = +1.8 V Leakage Current - <5 10 µA VBATT = +4.35 V, VCC = +4.35 V, VEN = 0 V, VMODE = 0 V Noise Power - -135 -135 -146 -133 - Harmonics 2fo 3fo, 4fo - -44 -51 -35 -42 dBc Coupling Factor - 20 - dB Directivity - 20 - dB Coupler In_Out Daisy Chain Insertion Loss - <0.25 - dB 698 MHz to 2620 MHz Pin 8 to 9, Shutdown Mode Gain Efficiency Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure 1930 MHz to 1990 MHz dBm/Hz GPS Band ISM Band - - -70 dBc P OUT ≤ +28.2 dBm In-band load VSWR < 5:1 Out-of-band load VSWR < 10:1 Applies over all operating ranges 8:1 - - VSWR Applies over full operating range Notes: (1)ACLR and Efficiency are measured at 1880 MHz. 4 POUT ≤ +28.2 dBm Data Sheet - Rev 2.4 11/2012 AWC6341 APPLICATION INFORMATION The Bias Control table below lists the recommended modes of operation for various applications. To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Two operating modes are recommended to optimize current consumption. High Bias/High Power operating mode is for POUT levels > 17 dBm. At about 17 dBm, the PA could be switched to Low Power Mode. Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to the VEN and VMODE voltages. Bias Modes The power amplifier may be placed in either Low or High Bias modes by applying the appropriate logic level (see Operating Ranges table) to the VMODE pin. Table 5: Bias Control POUT LEVELS BIAS MODE VEN VMODE VCC VBATT Low power ≤ +17 dBm Low +1.8 V +1.8 V 3.1 - 4.35 V > 3.1 V High power > +16 dBm High +1.8 V 0V 3.1 - 4.35 V > 3.1 V - Shutdown 0V 0V 3.1 - 4.35 V > 3.1 V APPLICATION Shutdown VBATT VBATT VCC C5 2.2 C5 µF 2.2 µF RFIN C1 0.1µF C1 0.1µF GND at slug 1 GND at slug 1 2 RFIN 3 VMODE 4 VVENEN 5 VMODE VBATT 2 VBATT RF 3IN RFIN VCC RFOUT 10 VCC RFOUT 9 C3 33pF 10 GND 8 Figure 3: Evaluation Board Schematic 5 Data Sheet - Rev 2.4 11/2012 0.1µF 9 CPLIN 8 CPLIN CPLIN 7 VMODE GND 7GND VMODE 5 6 CPL 6 OUT VEN VEN CPLOUT GND 4 C2 VCC C3 0.1µF 33pF C2 C4 CPLIN C4 2.2µF ceramic 2.2µF ceramic RFOUT CPLOUT RFOUT CPLOUT AWC6341 PACKAGE OUTLINE Figure 4: M45 Package Outline - 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module Pin 1 Identifier Date Code YY= Year WW= Work Week 6341 Part Number LLLLNN Lot Number YYWWCC Country Code(CC) Figure 5: Branding Specification - M45 Package 6 Data Sheet - Rev 2.4 11/2012 AWC6341 COMPONENT PACKAGING Pin 1 Figure 6: Tape & Reel Packaging Table 6: Tape & Reel Dimensions 7 PACKAGE TYPE TAPE WIDTH POCKET PITCH REEL CAPACITY MAX REEL DIA 3 mm x 3 mm x 1 mm 12 mm 4 mm 2500 7" Data Sheet - Rev 2.4 11/2012 AWC6341 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION AWC6341Q7 -30 oC to +90 oC RoHS Compliant 10 Pin 3 mm x 3 mm x 1 mm Tape and Reel, 2500 pieces per Reel Surface Mount Module AWC6341P9 -30 oC to +90 oC RoHS Compliant 10 Pin 3 mm x 3 mm x 1 mm Partial Tape and Reel Surface Mount Module COMPONENT PACKAGING ANADIGICS 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 Data Sheet - Rev 2.4 11/2012