AWU6618 HELP3ETM Dual-band IMT & EGSM WCDMA 3.4 V Linear Power Amplifier Module Data Sheet - Rev 2.5 FEATURES • InGaP HBT Technology • High Efficiency: • 38% @ POUT = +28.5 dBm • 23% @ POUT = +17 dBm • 9% @ POUT = +8.5 dBm AW U • Low Quiescent Current: 4 mA 661 • Internal Voltage Regulation TE • Built-in Directional Coupler • Common VMODE Control Line • Simplified VCC Bus PCB routing • Reduced External Component Count • Low Profile Surface Mount Package: 1 mm • RoHS Compliant Package, 260 oC MSL-3 M47 Package 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module LE APPLICATIONS O • IMT & EGSM Dual-band Wireless Handsets and Data Devices for HSDPA/HSPA networks. PRODUCT DESCRIPTION 8 O BS AWU6618 addresses the demand for increased integration in dual-band handsets for WCDMA networks. The small footprint 3 mm x 5 mm x 1 mm surface- mount RoHS compliant package contains independent RF PA paths to ensure optimal performance in both frequency bands, while achieving a 25% PCB space savings compared with solutions requiring two single-band PAs. The package pinout was chosen to enable handset manufacturers to easily route bias to both power amplifiers and simplify control with common mode pins. The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-the-art reliability, temperature stability, and ruggedness. The AWU6618 is part of ANADIGICS’ High-Efficiency-at-Low-Power (HELP™) family of WCDMA power amplifiers, which deliver low quiescent currents and significantly greater efficiency without the need of an external DC-DC converter. Through selectable bias modes, the AWU6618 achieves optimal efficiency, specifically at low- and mid-range power levels where the PA typically operates, thereby dramatically increasing handset talk-time. Its built-in voltage regulator eliminates the need for external switches. This PA has built-in directional couplers for each band, with a common coupler output port CPL_OUT. These couplers provide high directivity and 24 dB Coupling. The 3 mm x 5 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency and linearity in a 50 Ω system. 02/2012 VEN_900 1 14 GND Bias Control Voltage Regulation RFIN_900 2 CPL VMODE1 3 12 VCC VBATT 4 11 VCCA VMODE2 5 10 CPLOUT RFIN_IMT 6 VEN_IMT 7 13 RFOUT_900 CPL Bias Control Voltage Regulation 9 GND 8 RFOUT_IMT GND at Slug (pad) Figure 1: Block Diagram AWU6618 VEN_900 RFIN_900 RFOUT_900 VMODE1 VMODE2 CPLOUT TE RFIN_IMT VEN_IMT LE RFOUT_IMT Figure 2: Pinout Table 1: Pin Description 1 DESCRIPTION VEN_900 Enable Voltage for EGSM Band RFIN_900 RF Input for EGSM Band BS 2 NAME O PIN VMODE1 Mode Control Voltage for EGSM and IMT Bands 4 VBATT Battery Voltage 5 VMODE2 Mode Control Voltage for EGSM & IMT Band 6 RFIN_IMT RF Input for IMT Band 7 VEN_IMT Enable Voltage for IMT Band 8 RFOUT_IMT 9 GND 10 CPLOUT 11 VCCA 12 VCC 13 RFOUT_900 14 GND O 3 2 RF Output for IMT Band Ground Coupler Output Port Battery Voltage A Supply Voltage RF Output for EGSM Band Ground Data Sheet - Rev 2.5 02/2012 AWU6618 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VBATT, VCC, VCCA) 0 +5 V Mode Control Voltage (VMODE1, VMODE2) 0 +3.5 V Enable Voltage (VEN_CELL, VEN_PCS) 0 +3.5 V RF Input Power (PIN) - +10 dBm -40 +150 °C Storage Temperature (TSTG) TE Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges MIN TYP MAX UNIT LE PARAMETER COMMENTS 880 1920 - 915 1980 MHz +3.2 +3.4 +4.2 V +1.35 0 +1.8 - +3.1 +0.5 V PA "on" PA "shut down" +1.35 0 +1.8 - +3.1 +0.5 V Low Bias Mode High Bias Mode RF Output Power, Band 8, UMTS R99 WCDMA, HPM HSPA (MPR = 0 dB), HPM R99 WCDMA, MPM HSPA (MPR = 0 dB), MPM R99 WCDMA, LPM HSPA (MPR = 0 dB), LPM 28.0(1) 27.0(1) 16.5(1) 15.5(1) 8.0(1) 7.0(1) 28.5 27.5 17.0 16.0 8.5 7.5 - RF Output Power, Band 1, UMTS R99 WCDMA, HPM HSPA (MPR = 0 dB), HPM R99 WCDMA, MPM HSPA (MPR = 0 dB), MPM R99 WCDMA, LPM HSPA (MPR = 0 dB), LPM 27.7(1) 26.7(1) 16.0(1) 15.0(1) 7.5(1) 6.5(1) 28.2 27.2 16.5 15.5 8.0 7.0 - -30 - +90 Operating Frequency (f) Enable Voltage (VEN) O Supply Voltage (VCC and VBATT) O BS Mode Control Voltage (VMODE1, VMODE2) Case Temperature (TC) dBm dBm EGSM (Band 8) IMT (Band 1) 3GPP TS 34.121-1, REL8 Table C.11.1.3 SUBTEST 1 3GPP TS 34.121-1, REL8 Table C.11.1.3 SUBTEST 1 °C The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1)For operation at VCC = +3.2 V, POUT is derated by 0.5 dB. 3 Data Sheet - Rev 2.5 02/2012 AWU6618 Table 4: Electrical Specifications - EGSM Band (Band 8) (TC = +25 °C, VBATT = VCC = +3.4 V, VEN_CELL = +1.8 V, 50 Ω system, R99 uplink waveform) COMMENTS PARAMETER MIN TYP MAX UNIT Gain 25 14.5 9 27.5 17 11 30 19.5 14 dB +28.5 dBm 0 V +17 dBm 1.8 V +8.5 dBm 1.8 V 0V 0V 1.8 V ACLR1 @ 5 MHz Offset (1) - -43 -43 -41 -37 -36 -36 dBc +28.5 dBm 0 V +17 dBm 1.8 V +8.5 dBm 1.8 V 0V 0V 1.8 V ACLR2 @ 10 MHz Offset (1) - -58 -55 -55 -48 -48 -48 dBc +28.5 dBm 0 V +17 dBm 1.8 V +8.5 dBm 1.8 V 0V 0V 1.8 V Power-Added Efficiency (1) 33 18 6 38 22 9 - % +28.5 dBm 0 V +17 dBm 1.8 V +8.5 dBm 1.8 V 0V 0V 1.8 V Mode Control Current - Battery Current - TE 6.5 mA through VCC pin, VMODE1 = +1.8 V, VMODE2 =+1.8 V 0.1 0.2 mA through VMODE pins, VMODE1= +1.8 V, VMODE2 = +1.8 V 1.5 2.5 mA through VBATT pin, VMODE1 = +1.8 V, VMODE2 = +1.8 V - 0.15 0.25 mA through VEN_900 pin - -134 -132 Harmonics 2fo 3fo, 4fo - -42 -50 -30 -38 dBc Input Impedance - - 2:1 VSWR Coupling Factor - 23.4 - dB O Noise in Receive Band Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure dBm/Hz 925 MHz to 960 MHz POUT < +28.5 dBm - - -65 dBc POUT < +28.5 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating conditions 8:1 - - VSWR Applies over full operating conditions Notes: (1) Efficiency and ACLR measured at 897.5 MHz. 4 VMODE2 4 BS Enable Current VMODE1 LE - O Quiescent Current (Icq) POUT Data Sheet - Rev 2.5 02/2012 AWU6618 Table 5: Electrical Specifications - IMT Band (Band 1) (TC = +25 °C, VBATT = VCC = +3.4 V, VEN_PCS = +1.8 V, 50 Ω system) (R99 uplink waveform) TYP MAX UNIT 24 12 8 17 14.5 10 29.5 17 13 dB +28.2 dBm +16.5 dBm +8 dBm 0V 1.8 V 1.8 V 0V 0V 1.8 V ACLR1 @ 5 MHz Offset - -42 -43 -44 -37 -36 -36 dBc +28.2 dBm +16.5 dBm +8 dBm 0V 1.8 V 1.8 V 0V 0V 1.8 V ACLR2 @ 10 MHz Offset - -55 -56 -55 -48 -48 -48 dBc +28.2 dBm +16.5 dBm +8 dBm 0V 1.8 V 1.8 V 0V 0V 1.8 V Power-Added Efficiency (1) 33 21 6 37 24 9 - +28.2 dBm +16.5 dBm +8 dBm 0V 1.8 V 1.8 V 0V 0V 1.8 V Quiescent Current (Icq) - 4 6.5 Mode Control Current - Battery Current - VMODE1 VMODE2 TE POUT % mA through VCC pin, VMODE1 = +1.8 V, VMODE2 =+1.8 V LE Gain 0.1 0.2 mA through VMODE pins, VMODE1= +1.8 V VMODE2 = +1.8 V 1.4 2.5 mA through VBATT pin, VMODE1 = +1.8 V, VMODE2 = +1.8 V - 0.15 0.25 mA through VEN_IMT pin - <1 5 µA VBATT = +4.2 V, VCC = +4.2 V, VEN = 0 V, VMODE1 = 0 V, VMODE2 = 0 V Total Decoder Current on VBATT (Shutdown Mode) - 12 22 µA VBATT = 4.2 V, VCC = 4.2 V, VEN = 0 V, VMODE1 = VMODE2 = 0 V Noise in Receive Band - -136 -134 dBm/Hz Harmonics 2fo 3fo, 4fo - -42 -50 -30 -38 dBc Input Impedance - - 2:1 VSWR Coupling Factor - 22.5 - dB Enable Current O BS HBT Leakage Current on VCC (Shutdown mode) Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure 2110 MHz to 2170 MHz POUT < +28.2 dBm - - -65 dBc POUT < +28.2 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating conditions 8:1 - - VSWR Applies over full operating conditions Notes: (1) ACPRs and Efficiency measured at 1950 MHz. 5 COMMENTS MIN O PARAMETER Data Sheet - Rev 2.5 02/2012 AWU6618 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to the VENABLE and VMODE voltages. Bias Modes, Medium Bias Mode The power amplifier may be placed in Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE1, and VMODE2 pins. The Bias Control table lists the recommended modes of operation for various applications. Vcontrols Venable/Vmode(s) TE On Sequence Start T_0N = 0µ Rise/Fall Max 1µS Defined at 10% to 90% of Min/Max Voltage Off Sequence Start T_0FF = 0µ OFF Sequence LE ON Sequence RFIN_900, IMT O notes 1,2 VEN_900, IMT BS VCC, VCCA note 1 T_0N+1µS T_0N+3µS T_0FF+2µS T_0FF+3µS Referenced After 90% of Rise Time Referenced Before10% of Fall Time Figure 3: Recommended ON/OFF Timing Sequence O Notes: (1) Level might be changed after RF is ON. (2) RF OFF defined as PIN ≤ -30 dBm. (3) Switching simultaneously between VMODE and VEN is not recommended Table 6: Bias Control POUT LEVELS BIAS MODE VEN VMODE1 VMODE2 VCC VBATT WCDMA - low power (Low Bias Mode) < +8.5 dBm Low +1.8 V +1.8 +1.8 V 3.2 - 4.2 V > 3.2 V WCDMA - med power (Medium Bias Mode) > 8 dBm < +17 dBm Low +1.8 V +1.8 V 0V 3.2 - 4.2 V > 3.2 V WCDMA - high power (High Bias Mode) > +16 dBm High +1.8 V 0V 0V 3.2 - 4.2 V > 3.2 V - Shutdown 0V 0V 0V 3.2 - 4.2 V > 3.2 V APPLICATION Shutdown 6 Data Sheet - Rev 2.5 02/2012 AWU6618 VEN_900 1 14 Bias Control Voltage Regulation RFIN_900 CPL 2 13 68 pF 12 3 VMODE1 RFOUT_900 VCC 1000 pF 2.2 F 68pF 4 11 TE VBATT 68 pF 5 RFIN_IMT 6 7 VEN_IMT 10 CPL Bias Control Voltage Regulation O GND at Slug (pad) O BS Figure 4: Application Circuit 7 Data Sheet - Rev 2.5 02/2012 CPLOUT 9 LE VMODE2 2.2 F 8 33 pF RFOUT_IMT AWU6618 BS O LE TE PACKAGE OUTLINE O Figure 7: Package Outline - 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module Pin 1 Identifier Date Code YY= Year WW= Work Week 6618R LLLLNN CC YYWW Figure 8: Branding Specification 8 Data Sheet - Rev 2.5 02/2012 Part Number Lot Number Country Code AWU6618 LE TE COMPONENT PACKAGING O BS O Figure 5: Carrier Tape Figure 6: Reel 9 Data Sheet - Rev 2.5 02/2012 AWU6618 ORDERING INFORMATION TEMPERATURE RANGE PACKAGE DESCRIPTION COMPONENT PACKAGING AWU6618RM47Q7 -30 °C to +90 °C RoHS Compliant 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module Tape and Reel, 2500 pieces per Reel AWU6618RM47P9 -30 °C to +90 °C RoHS Compliant 14 Pin 3 mm x 5 mm x 1 mm Surface Mount Module Partial Tape and Reel ANADIGICS BS O LE TE ORDER NUMBER O 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 10 Data Sheet - Rev 2.5 02/2012