AZM AZ10EP16D

ARIZONA MICROTEK, INC.
AZ10EP16
AZ100EP16
ECL/PECL Differential Receiver
FEATURES
PACKAGE AVAILABILITY
•
•
•
•
Silicon-Germanium for High Speed
Operation
150ps Typical Propagation Delay
Internal Input Pulldown Resistors
Functionally Equivalent to ON
Semi MC10EP16 & MC100EP16
PACKAGE
PART NUMBER
SOIC 8
SOIC 8
TSSOP 8
TSSOP 8
1
2
AZ10EP16D
AZ100EP16D
AZ10EP16T
AZ100EP16T
MARKING
AZM10EP16
AZM100EP16
AZTEP16
AZHEP16
NOTES
1,2
1,2
1,2
1,2
Add R1 at end of part number for 7 inch (1K parts), R2 for 13 inch (2.5K parts)
Tape & Reel.
Date Code “YWW” on underside of part.
DESCRIPTION
The AZ10/100EP16 is a Silicon–Germanium (SiGe) differential receiver. The device is functionally equivalent
to the AZ10/100EL16 device with higher performance capabilities. With output transition times significantly faster
than the AZ10/100EL16, the EP16 is ideally suited for interfacing with high frequency sources.
The EP16 provides a VBB output for single-ended use or a DC bias reference for AC coupling to the device. For
single-ended input applications, the VBB reference should be connected to one side of the D/D
¯ differential input pair.
The input signal is then fed to the other D/D
¯ input. The VBB pin can support 1.5mA sink/source current. When
used, the VBB pin should be bypassed to ground via a 0.01μF capacitor.
Under open input conditions internal input clamps will force the Q output LOW.
NOTE: Specifications in ECL/PECL tables are valid when thermal equilibrium is established.
PIN DESCRIPTION
PIN
D, D
¯
Q, Q
¯
VBB
VCC
VEE
NC
FUNCTION
Data Inputs
Data Outputs
Reference Voltage Output
Positive Supply
Negative Supply
No Connect
LOGIC DIAGRAM AND PINOUT ASSIGNMENT
NC
1
8
VCC
D
2
7
Q
D
3
6
Q
VBB
4
5
VEE
1630 S. STAPLEY DR., SUITE 127 • MESA, ARIZONA 85204 • USA • (480) 962-5881 • FAX (480) 890-2541
www.azmicrotek.com
AZ10EP16
AZ100EP16
Absolute Maximum Ratings are those values beyond which device life may be impaired.
Symbol
VCC
VI
VEE
VI
IOUT
TA
TSTG
Characteristic
PECL Power Supply (VEE = 0V)
PECL Input Voltage
(VEE = 0V)
ECL Power Supply
(VCC = 0V)
ECL Input Voltage
(VCC = 0V)
Output Current
--- Continuous
--- Surge
Operating Temperature Range
Storage Temperature Range
Rating
0 to +4.5
0 to +4.5
-4.5 to 0
-4.5 to 0
50
100
-40 to +85
-65 to +150
Unit
Vdc
Vdc
Vdc
Vdc
mA
°C
°C
10K ECL DC Characteristics (VEE = -3.0V to -3.6V, VCC = GND)
Symbol
1
VOH
VOL
VIH
VIL
VBB
IIH
IIL
IEE
1.
Characteristic
Output HIGH Voltage
Output LOW Voltage1
Input HIGH Voltage
Input LOW Voltage
Reference Voltage
Input HIGH Current
Input LOW Current
Min
-1135
-1935
-1200
-1935
-1430
-40°C
Typ
Max
-885
-1685
-885
-1530
-1300
175
D
D
¯
0.5
-150
Power Supply Current
20
25
33
Each output is terminated through a 50Ω resistor to VCC – 2V.
Min
0°C
Typ
-1380
Max
-1270
175
0.5
-150
21
26
34
0°C
Typ
Max
Min
-1070
-1870
-1150
-1870
-1350
0.5
-150
21
25°C
Typ
-945
-1745
27
Max
-820
-1620
-820
-1450
-1250
175
35
Min
-1010
-1810
-1090
-1810
-1310
0.5
-150
23
85°C
Typ
Max
-760
-1560
-760
-1410
-1190
175
Unit
mV
mV
mV
mV
mV
μA
μA
29
37
mA
10K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V)
Symbol
VOH
VOL
VIH
VIL
VBB
IIH
IIL
IEE
1.
2.
Characteristic
1,2
Min
2165
1365
2100
1365
1870
-40°C
Typ
Max
2415
1615
2415
1770
2000
175
Min
Min
2230
1430
2035
1430
1950
Output HIGH Voltage
Output LOW Voltage1,2
Input HIGH Voltage1
Input LOW Voltage1
Reference Voltage1
1920
2030
Input HIGH Current
175
Input LOW Current
D
0.5
0.5
0.5
D
¯
-150
-150
-150
Power Supply Current
20
25
33
21
26
34
21
For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value.
Each output is terminated through a 50Ω resistor to VCC – 2V.
25°C
Typ
2355
1555
27
Max
2480
1680
2480
1850
2050
175
35
Min
2290
1490
2210
1490
1990
0.5
-150
23
85°C
Typ
Max
2540
1740
2540
1890
2110
175
Unit
mV
mV
mV
mV
mV
μA
μA
29
37
mA
100K ECL DC Characteristics (VEE = -3.0V to -3.6V, VCC = GND)
Symbol
VOH
VOL
VIH
VIL
VBB
IIH
IIL
IEE
1.
Characteristic
1
Output HIGH Voltage
Output LOW Voltage1
Input HIGH Voltage
Input LOW Voltage
Reference Voltage
Input HIGH Current
Input LOW Current
D
D
¯
Min
-1085
-1830
-1220
-1830
-1440
-40°C
Typ
Max
-880
-1555
-880
-1540
-1320
175
0.5
-150
Power Supply Current
19
24
32
Each output is terminated through a 50Ω resistor to VCC – 2V.
November 2006 * REV - 5
Min
-1025
-1810
-1160
-1810
-1380
0.5
-150
20
0°C
Typ
25
www.azmicrotek.com
2
Max
-880
-1620
-880
-1480
-1260
175
33
Min
-1025
-1810
-1160
-1810
-1380
0.5
-150
21
25°C
Typ
-955
-1705
26
Max
-880
-1620
-880
-1480
-1260
175
35
Min
-1025
-1810
-1160
-1810
-1380
0.5
-150
23
85°C
Typ
Max
-880
-1620
-880
-1480
-1260
175
Unit
mV
mV
mV
mV
mV
μA
μA
29
38
mA
AZ10EP16
AZ100EP16
100K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V)
Symbol
IEE
1.
2.
Min
2215
1470
2080
1470
1860
1,2
VOH
VOL
VIH
VIL
VBB
IIH
IIL
Characteristic
Output HIGH Voltage
Output LOW Voltage1,2
Input HIGH Voltage1
Input LOW Voltage1
Reference Voltage1
Input HIGH Current
Input LOW Current
-40°C
Typ
Max
2420
1745
2420
1760
1980
175
Min
2275
1490
2140
1490
1920
0°C
Typ
Max
2420
1680
2420
1820
2040
175
Min
2275
1490
2140
1490
1920
0.5
0.5
0.5
-150
-150
-150
Power Supply Current
19
24
32
20
25
33
21
For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value.
Each output is terminated through a 50Ω resistor to VCC – 2V.
25°C
Typ
2345
1595
Max
2420
1680
2420
1820
2040
175
D
D
¯
26
35
Min
2275
1490
2140
1490
1920
85°C
Typ
Max
2420
1680
2420
1820
2040
175
Unit
mV
mV
mV
mV
mV
μA
μA
0.5
-150
23
29
38
Min
85°C
Typ
Max
mA
AC Characteristics (VEE = -3.0 to -3.6V, VCC = GND or VEE = GND, VCC = +3.0V to +3.6V)
Symbol
Characteristic
tSKEW
VPP (AC)
Maximum Toggle
Frequency4
Input to
(DIFF)
Output Delay
1
Duty Cycle Skew (Diff)
Minimum Input Swing2
VCMR
Common Mode Range3
fmax
tPLH / tPHL
1.
2.
3.
4.
-40°C
Typ
Max
Min
>4
100
160
Max
Min
>4
240
100
5
150
VEE +
2.0
0°C
Typ
VCC
Max
>4
160
240
5
20
150
VEE +
2.0
25°C
Typ
VCC
100
150
VEE +
2.0
>4
160
240
5
20
VCC
120
190
280
ps
5
20
ps
mV
VCC
V
150
VEE +
2.0
Large Signal Performance*
900
800
700
600
500
400
300
200
100
0
0
1000
2000
3000
4000
5000
FREQUENCY (MHz)
*Measured using a 750mV differential input source at 50% duty cycle.
November 2006 * REV - 5
www.azmicrotek.com
3
Unit
GHz
Output Rise/Fall Times Q
120
170
130
180
130
180
150
200
(20% - 80%)
Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device.
VPP is the minimum peak-to-peak differential input swing for which AC parameters are guaranteed.
The VCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within
the specified range and the peak-to-peak voltage lies between VPP(min) and 1V.
See Graph Below.
VOUTpp (mV)
tr / t f
Min
6000
ps
AZ10EP16
AZ100EP16
PACKAGE DIAGRAM
SOIC 8
NOTES:
1.
DIMENSIONS D AND E DO NOT
INCLUDE MOLD PROTRUSION.
2.
MAXIMUM MOLD PROTRUSION
FOR D IS 0.15mm.
3.
MAXIMUM MOLD PROTRUSION
FOR E IS 0.25mm.
November 2006 * REV - 5
DIM
A
A1
A2
A3
bp
c
D
E
e
HE
L
Lp
Q
v
w
y
Z
θ
www.azmicrotek.com
4
MILLIMETERS
MIN
MAX
1.75
0.10
0.25
1.25
1.45
0.25
0.36
0.49
0.19
0.25
4.8
5.0
3.8
4.0
1.27
5.80
6.20
1.05
0.40
1.00
0.60
0.70
0.25
0.25
0.10
0.30
0.70
8O
0O
INCHES
MIN
MAX
0.069
0.004
0.010
0.049
0.057
0.01
0.014
0.019
0.0075
0.0100
0.19
0.20
0.15
0.16
0.050
0.228
0.244
0.041
0.016
0.039
0.024
0.028
0.01
0.01
0.004
0.012
0.028
0O
8O
AZ10EP16
AZ100EP16
PACKAGE DIAGRAM
TSSOP 8
DIM
A
A1
A2
A3
bp
c
D
E
e
HE
L
Lp
v
w
y
Z
θ
NOTES:
1.
DIMENSIONS D AND E DO NOT
INCLUDE MOLD PROTRUSION.
2.
MAXIMUM MOLD PROTRUSION
FOR D IS 0.15mm.
3.
MAXIMUM MOLD PROTRUSION
FOR E IS 0.25mm.
November 2006 * REV - 5
www.azmicrotek.com
5
MILLIMETERS
MIN
MAX
1.10
0.05
0.15
0.80
0.95
0.25
0.25
0.45
0.15
0.28
2.90
3.10
2.90
3.10
0.65
4.70
5.10
0.94
0.40
0.70
0.10
0.10
0.10
0.35
0.70
6O
0O
AZ10EP16
AZ100EP16
Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc.
makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona
Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license
rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems
intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a
situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries,
affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly
or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part.
November 2006 * REV - 5
www.azmicrotek.com
6