Capacitors with 4 Snap-In Terminals and Solder Pins 85 °C B 43 511 B 43 521 LL grade Especially high volumetric efficiency Construction ● ● ● ● Charge-discharge proof, polar Aluminum case, fully insulated Overload protection by preset break point in case Negative pole brought out to solder pin, but not insulated from case Terminals KAL0409-D B 43 511 B 43 521 ● Solder pin mounting on printed circuit boards, pins fit standardized spacings on PCB ● 4 snap-in terminals (6,3 mm and 4,5 mm length) Features ● Outstanding ripple current capability ● Extremely small dimensions, i.e. especially high volumetric efficiency ● Many different case sizes ● Pinning ensures correct insertion Applications ● For frequency converters ● For switch-mode power supplies in industrial and consumer electronics Specifications and characteristics in brief Rated voltage UR 350 to 450 V– Surge voltage US 1,1 · UR Rated capacitance CR 390 … 2 200 µF Capacitance tolerance ± 20 % M Useful life 40 °C, UR 85 °C, UR; I~R > 200 000 h (1,6 · I~R,85°C) > 12 000 h Failure percentage ≤1% (during useful life) Failure rate ≤ 40 fit (≤ 40 · 10– 9/h) Voltage endurance test 3 000 h, 85 °C (at UR) 174 Siemens Matsushita Components B 43 511 B 43 521 Specifications and characteristics in brief Leakage current Ilka (5 min, 20 °C) C R U R 0,7 I lka ≤ 0,3 µA ⋅ -------- ⋅ -------- + 4 µA µF V Self-inductance LESL approx. 20 nH IEC climatic category in accordance with IEC 68–1 ≤ 400 V–: 40/085/56 (–40 °C/+85 °C, 56 days damp heat test) 450 V–: 25/085/56 (–25 °C/+85 °C, 56 days damp heat test) Detail specification similar to CECC 30 301-805 Sectional specification IEC 384–4 Vibration resistance in accordance with IEC 68–2–6, test Fc: frequency range 10 … 55 Hz, duration 3 × 2 h displacement amplitude 0,35 mm, acceleration max. 5 g Siemens Matsushita Components 175 B 43 511 B 43 521 Dimensional drawings d = 35 mm Solder pins d = 40 mm 2 1 1 4 15 15 d 1) 1) 20±0,1 7,5±0,1 ø1,3+0,1 ø1,3+0,1 l l max 3 MountingMontagelochung holes (view(Ansicht onto von solder side) der Lötseite) 1 1 2 17,5±0,1 4,5±0,5 1) Permissible range of positions for pole identification marks 4 20±0,1 15±0,1 3 3 17,5±0,1 2 3 0,8x1,1 _ 0,1 KAL0400-9 Pole markings: Plus: 1; Minus: – All pin holes must be drilled into the PC-board, since the unconnected pins serve as mountings. These pins must be soldered to isolated pads or pads with the same potential as the negative pole. 4 snap-in terminals Mounting holes Montagelochung 30 ±3 30 30 PluspolPlus pole marking Kennzeichnung d 0´ Minus pole marking Minuspol Kennzeichnung 2±0,1 6,3±1 l 22,5±0,1 _ 0,1 0,8 +0,2 1,5±0,2 0,8 KAL0401-H Standard snap-in terminals: length (6,3 ± 1) mm. Also available with a length of (4,5 – 1) mm. For ordering example cf. page 178 176 Dimensions (mm) Approx. d +1 l ± 2 l max weight (g) Packing units (pieces) 35 35 35 35 35 50 60 70 80 100 54 64 74 84 104 63 76 88 101 126 144 144 72 72 72 40 40 40 40 40 40 40 50 60 70 80 100 44 54 64 74 84 104 71 89 107 125 143 178 96 96 96 48 48 48 45 45 45 45 45 45 40 50 60 70 80 100 − − − − − − 90 113 136 158 181 226 80 80 80 40 40 40 Siemens Matsushita Components B 43 511 B 43 521 Overview of available types UR (V–) 350 CR (µF) Case dimensions d × l (mm) 400 450 35 × 50 40 × 40 390 470 35 × 50 40 × 40 35 × 60 40 × 50 45 × 40 560 35 × 50 35 × 60 45 × 40 35 × 70 40 × 60 680 35 × 60 40 × 50 35 × 70 40 × 60 45 × 50 35 × 80 40 × 60 45 × 50 820 35 × 70 40 × 60 35 × 80 40 × 60 40 × 70 45 × 60 1 000 35 × 80 40 × 60 45 × 50 35 × 100 40 × 70 45 × 60 40 × 100 45 × 70 1 500 40 × 80 45 × 70 40 × 100 45 × 80 45 × 100 45 × 100 1 800 2 200 45 × 100 The capacitance and voltage ratings listed above are available in different cases upon request. Other voltage and capacitance ratings are also available upon request. Capacitors with solder pins are only available in 35 and 40 mm case diameters. Siemens Matsushita Components 177 B 43 511 B 43 521 Technical data and ordering codes UR CR V– µF Case dimensions d×l mm RESR, max 100 Hz 20 °C mΩ Zmax 10 kHz 20 °C mΩ I~max 100 Hz 40 °C A I~R 100 Hz 85 °C A Ordering code 1) Short code B43511-, B43521350 560 680 680 820 820 1 000 1 000 1 000 1 500 1 500 2 200 35 × 50 35 × 60 40 × 50 35 × 70 40 × 60 35 × 80 40 × 60 45 × 50 40 × 80 45 × 70 45 × 100 230 190 190 160 160 130 130 130 90 90 60 190 150 150 130 130 110 110 110 70 70 50 7,0 8,2 8,1 9,6 9,5 11 10 9,9 14 14 19 3,2 3,7 3,7 4,4 4,3 5,1 4,8 4,5 6,5 6,2 8,6 -A4567-M -A4687-M -C4687-M -A4827-M -C4827-M -A4108-M -C4108-M -E4108-M -A4158-M -C4158-M -A4228-M 400 470 470 560 560 680 680 680 820 820 1 000 1 000 1 000 1 500 1 500 1 800 35 × 50 40 × 40 35 × 60 45 × 40 35 × 70 40 × 60 45 × 50 35 × 80 40 × 60 35 × 100 40 × 70 45 × 60 40 × 100 45 × 80 45 × 100 280 280 230 230 190 190 190 160 160 130 130 130 90 90 80 220 220 190 190 150 150 150 130 130 110 110 110 70 70 60 6,4 6,2 7,5 6,9 8,7 8,7 8,1 10 9,5 12 11 11 16 14 17 2,9 2,8 3,4 3,1 4,0 3,9 3,7 4,6 4,3 5,6 5,1 4,8 7,2 6,5 7,8 -A9477-M -C9477-M -A9567-M -C9567-M -A9687-M -C9687-M -E9687-M -A9827-M -C9827-M -C9108-M -A9108-M -B9108-M -A9158-M -C9158-M -A9188-M Capacitors with solder pins are only available in 35 and 40 mm case diameters. 1) To obtain the required ordering code, prefix the type number to the short code. E. g.: B43511-A4567-M B43521-…(solder pins) B43511-…(4 snap-in terminals, standard version with terminal length 6,3 mm. For short-terminal version (length 4,5 mm), append code number "7" to the tolerance code. E. g.: B43511-A4567-M7) 178 Siemens Matsushita Components B 43 511 B 43 521 Technical data and ordering codes UR CR V– µF Case dimensions d×l mm RESR, max 100 Hz 20 °C mΩ Zmax 10 kHz 20 °C mΩ I~max 100 Hz 40 °C A I~R 100 Hz 85 °C A Ordering code 1) 520 520 430 430 430 360 360 300 300 300 250 250 200 200 140 410 410 340 340 340 290 290 240 240 240 200 200 160 160 110 5,8 5,7 6,8 6,7 6,3 7,9 7,9 9,2 8,7 8,1 10 9,5 13 11 16 2,6 2,6 3,1 3,1 2,9 3,6 3,6 4,2 3,9 3,7 4,6 4,3 5,8 5,1 7,1 -A5397-M -C5397-M -A5477-M -C5477-M -E5477-M -A5567-M -C5567-M -A5687-M -C5687-M -E5687-M -A5827-M -C5827-M -A5108-M -C5108-M -A5158-M Short code B43511-, B43521450 390 390 470 470 470 560 560 680 680 680 820 820 1 000 1 000 1 500 35 × 50 40 × 40 35 × 60 40 × 50 45 × 40 35 × 70 40 × 60 35 × 80 40 × 60 45 × 50 40 × 70 45 × 60 40 × 100 45 × 70 45 × 100 Capacitors with solder pins are only available in 35 and 40 mm case diameters. 1) To obtain the required ordering code, prefix the type number to the short code. E. g.: B43511-A5379-M B43521-…(solder pins) B43511-…(4 snap-in terminals, standard version with terminal length 6,3 mm. For short-terminal version (length 4,5 mm), append code number "7" to the tolerance code. E. g.: B43511-A5397-M7) Siemens Matsushita Components 179 B 43 511 B 43 521 Useful life versus ambient temperature TA under ripple current operating conditions 1) KAL0410-G 2,5 I~Ι ~ ~R, 85°C ΙI~ Nenn, 85 C 2,0 1,5 50 60 70 80 Permissible ripple current I~ versus frequency f Ι ~f 90 C 100 TA Equivalent series resistance RESR versus frequency f Typical behavior KAL0411-P 1,5 Ι ~100 Hz 12 000h 25 000h 50 000h 100 000h 0 40 175 000h 0,5 250 000h 1,0 1,4 1,3 1,2 <_ 400 V 450 V 1,1 1,0 0,9 0,8 0,7 1 10 10 2 10 3 Hz f 10 4 1) Refer to page 34 for an explanation on how to interpret the useful life graphs. 180 Siemens Matsushita Components B 43 511 B 43 521 Impedance Z at f = 10 kHz versus frequency f Typical behavior KAL0462-Y 10 2 Ω Z 10 1 5 10 0 5 10 _1 680 µ F / 450 V 820 µ F / 400 V 5 10 _2 10 1 10 2 10 3 10 4 10 5 Hz 10 6 f Siemens Matsushita Components 181