Analog 4-wire PET-On-Glass Touch Screen Specification 1. Mechanical Dimensions and Construction 1.1 General: Analog Resistive touch screen is laminated by ITO PET to ITO glass. 1.2 Construction : Item 1 2 3 4 5 6 7 8 9 10 Description ITO PET (Top layer) Material Remarks 0.188mm ITO PET Film Antiglare coating Surface hardness: 3H Resistance:300~600Ω/□ ITO Patterned Glass (Bottom 1.57mm ITO Glass Resistance:300~600Ω/□ layer) Tail PET Film Integral to Top layer circuit Tail insulation PET Film Connector AMP Compatible Pitch : 2.54mm Top layer circuit Silver ink Bottom layer circuit Silver ink Layer to layer contacted Silver ink Dot spacer UV Cure ink Isolation Layer Isolation Adhesive Touch screen side view: Changes that contribute to technical improvement are subject to alternations 2002 Datum Name Bearb. 24.10. Maurer Gepr. 24.10. Maurer TOUCHSCREEN 5,77“, 4 Wire Vert. EDV-Datasheet SPECIFICATIONS OF ANALOG RESISTIVE don’t change manually Manufactured bei Apex Material Technology Corp. PET-ON-GLASS TOUCH SCREEN H Zu Änd. Datum Name D 79346 Endingen 1070.0417 Blatt 1 von 5 Index: - 1.3 Input Method and Activation Force Input Method 1.6mm dia. Delrin stylus 16mm dia. Silicon "finger" Average Activation Force 10~70 grams 10~ 80 grams 2. Typical Optical Characteristics 2.1 Visible Light Transmission: >80% 2.2 Haze: 3~7 % (JIS K-7105) 3. Electrical Specifications 3.1 3.2 3.3 3.4 3.5 3.6 3.7 Operating Voltage: 5.5V or less Contact current: 20mA (maximum) Circuit close resistance: X : 400~1000Ω Y : 200~650Ω Circuit open resistance: > 10MΩ at 25VDC Contact bounce: < 10ms Linear Test : <1.5 % Capacitance:100nF(maximum) 4. Linearity 4.1 Linear Test Specification Direction X: <1.5 % Direction Y: <1.5 % 4.2.1 Line Test Circuit for Y CoordinateAdd 5V between Y1 and Y2 touch the point C0R0 to C9R9 separately, and measure the voltage from X1 as the following drawing. Changes that contribute to technical improvement are subject to alternations 2002 Datum Name Bearb. 24.10. Maurer Gepr. 24.10. Maurer TOUCHSCREEN 5,77“, 4 Wire Vert. EDV-Datasheet SPECIFICATIONS OF ANALOG RESISTIVE don’t change manually Manufactured bei Apex Material Technology Corp. PET-ON-GLASS TOUCH SCREEN H Zu Änd. Datum Name D 79346 Endingen 1070.0417 Blatt 2 von 5 Index: - 4.3 Calculate Linearity : For the First Row0 R0avg = ( VC0 + VC1 + VC2 +- - - - - - - + VC9) ¸ 10 R0max = The maximum voltage in Row 0 R0min = The minimum voltage in Row 0 R0 linear1 = ½ R0 max – R0 avg. ½ ¸ R0 avg. * 100% R0 linear2 = ½ R0 min – R0 avg. ½ ¸ R0 avg. * 100% R0 linear = max (R0 linear1, R0 linear2) 4.4 For X Coordinate Test Add 5 voltage between X1 and X2 touch the point C0R0 to C9R9 separately and measure the voltage from Y1 as the above drawing 4.5 Calculate Linearity : For the First Column0 C0avg = ( VR0 + VR1 + VR2 +- - - - - - - + VR9 ) ¸ 10 C0max = The maximum voltage in Column 0 C0min = The minimum voltage in Column 0 C0 linear1 = ½ C0 max – C0 avg. ½ ¸ C0 avg. * 100% C0 linear2 = ½ C0 min – C0 avg. ½ ¸ C0 avg. * 100% C0 linear = max ( C0 linear1 ,C0 linear2 ) Changes that contribute to technical improvement are subject to alternations 2002 Datum Name Bearb. 24.10. Maurer Gepr. 24.10. Maurer TOUCHSCREEN 5,77“, 4 Wire Vert. EDV-Datasheet SPECIFICATIONS OF ANALOG RESISTIVE don’t change manually Manufactured bei Apex Material Technology Corp. PET-ON-GLASS TOUCH SCREEN H Zu Änd. Datum Name D 79346 Endingen 1070.0417 Blatt 3 von 5 Index: - 5. Environment Specification 5.1 5.2 Operating Temperatur Storage Temperature - 10° C ~ + 60° C - 20° C ~ + 80° C Humidity less than 90% RH at Ambient Humidity 6. Reliability Test 6.1 Exposure to high temperature Touch panel is put into a test machine at the condition of 80 for 120 hours. Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 6.2 Exposure to low temperature Touch panel is put into a test machine at the condition of -20 for 120 hours. Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 6.3 Exposure to constant temperature and humidity Touch panel is put into a test machine at the condition of 60 , 90%RH for 120 hours. Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 6.4 Thermal Shock Touch panel is put into a test machine at the condition of -20 for 30 minutes, and then 80 for 30 minutes. The process is repeated by 10 cycles. Then it is left at the room temperature for 24 hours or more. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 Changes that contribute to technical improvement are subject to alternations 2002 Datum Name Bearb. 24.10. Maurer Gepr. 24.10. Maurer TOUCHSCREEN 5,77“, 4 Wire Vert. EDV-Datasheet SPECIFICATIONS OF ANALOG RESISTIVE don’t change manually Manufactured bei Apex Material Technology Corp. PET-ON-GLASS TOUCH SCREEN H Zu Änd. Datum Name D 79346 Endingen 1070.0417 Blatt 4 von 5 Index: - 7. Durability test: 7.1 Finger touches Touch panel is hit 10 millions times with a silicone rubber of R8 finger, hitting rate is by 250g at 2 times per second. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 7.2 Stylus writing Touch panel is drawn by R0.8 Derlin stylus pen, at 250g forces, repeat one inch by 100K times. The measurement must satisfy the following: - Circuit close resistance: as Sec. 3.3 - Circuit open resistance: as Sec. 3.4 - Contact bounce: as Sec. 3.5 - Linearity test: as Sec. 3.6 8. Optical Performance 8.1 Optical inspection method and optical defect standards refer to document. A001-1; Touch Screen Optical Quality Standard. 8.2 Outside to Viewing Area : any optical defected in this area need to be ignored if no effected to touch screen function. 8.3 Silver Bus Pattern defect : Voids in traces to be less than 50% of the trace width. 8.3.1 Silver Bus Pattern gap: >0.1mm 8.3.2 Silver Bus and Active area gap: No silver ink may project beyond the viewing area. 8.3.3 Printed silver tails must not be bent to less than 4mm radius. Maximum number of bend repetitions is 10. 8.4 Glass defects such as edge chips and scratches refer to A001-1 Touch Screen Optical Quality Standard. 8.5 Others 8.5.1 Folding line should be avoided on the pressure sensitive adhesive. 8.5.2 Refer to document A001-1, Touch Screen Optical Quality Standard. 8.5.3 Always store the touch screen in its original shipping container under normal conditions (20~25°C, 65% RH) Changes that contribute to technical improvement are subject to alternations 2002 Datum Name Bearb. 24.10. Maurer Gepr. 24.10. Maurer TOUCHSCREEN 5,77“, 4 Wire Vert. EDV-Datasheet SPECIFICATIONS OF ANALOG RESISTIVE don’t change manually Manufactured bei Apex Material Technology Corp. PET-ON-GLASS TOUCH SCREEN H Zu Änd. Datum Name D 79346 Endingen 1070.0417 Blatt 5 von 5 Index: -