STMICROELECTRONICS SPC56ELADPT144S

SPC56ELADPT144S
SPC56ELxx microcontroller family evaluation board
Data brief − production data
Features
■
SPC56xx modular evaluation system
■
On/off power switch with LED indicators
■
Board power supply: 12 VDC external supply
voltage
■
Onboard STMicroelectronics® L9758 voltage
regulator with three simultaneous output at
1.2 V, 3.3 V and 5 V
■
Possibility to configure onboard peripherals to
operate at 5 V or 3.3 V logic levels, depending
on target
■
Two CAN channels with jumper enable
– One CAN channel with High-Speed
transceiver and DB9 male connector
– One CAN channel with Low-Speed Fault
Tolerant and High-Speed transceiver
(selectable with jumpers) and DB9 male
connector
■
Specifications:
– Board size 110 mm x 75 mm
– 12 VDC Center Positive power supply with
2.5/5.5 mm barrel connector
Description
■
Two LIN channels with jumper enable
– One channel with transceiver and pin
header connector populated
– One channel with footprints only
■
One SCI channel with jumper enables,
transceiver and DB9 female connector
The SPC56ELADPT144S is an evaluation system
supporting the STMicroelectronics® SPC56ELxx
family of automotive microprocessors. The
complete system consists of a SPC56XXMB
motherboard and a mini module which plugs
directly into the motherboard. Different mini
modules are available for evaluating the whole
family of devices in all supported packages.
■
Two FlexRay channels with jumper enables
– One channel with transceiver and DB9
male connector
– One channel with footprint only
The evaluation system allows full access to the
CPU, to all of the CPU’s I/O signals and to the
motherboard’s peripherals (such as CAN, SCI
and LIN).
■
Four user push buttons with jumper enable and
polarity selection
■
Four user LED’s with jumper enables
The mini module itself can be used as a standalone unit when access to the I/O pins or
peripherals is not needed.
■
One potentiometer for analog voltage input
■
Pin array for accessing all I/O signals
■
Expansion connectors for accessing all I/O
signals
■
Prototyping area with 0.1” spacing and SOIC
footprint
September 2012
Doc ID 023653 Rev 1
This is information on a product in full production. For further information contact your local STMicroelectronics sales
office.
1/4
www.st.com
1
Order codes
1
SPC56ELADPT144S
Order codes
Table 1.
Device summary
Part numbers
SPC56XXMB
SPC56ELADPT144S
2/4
Device supported
Mother board for SPC56xx family of devices
Mini module for SPC56EL60L5
Doc ID 023653 Rev 1
SPC56ELADPT144S
2
Revision history
Revision history
Table 2.
Document revision history
Date
Revision
20-Sep-2012
1
Changes
Initial release.
SPC56ELADPT144S was previously in document DM00044221
(DocID 022591) revision 1.
Doc ID 023653 Rev 1
3/4
SPC56ELADPT144S
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
4/4
Doc ID 023653 Rev 1