PI6LC48H02

PI6LC48H02
PCIe® 3.0/2.0/1.0 Clock Generator with 2 HCSL Outputs
Features
Description
ÎÎPCIe® 3.0/2.0/1.0 compliant
The PI6LC48H02 is a clock generator compliant to PCI Express®
3.0/2.0/1.0 and Ethernet requirements. The device is used for PC
or embedded systems.
àà PCIe 3.0 Phase jitter - 0.45ps RMS (High Freq. Typ.)
ÎÎLVDS compatible outputs
ÎÎSupply voltage of 3.3V ±10%
The PI6LC48H02 provides two differential (HCSL) or LVDS outputs. Using Pericom's patented Phase Locked Loop (PLL) techniques, the device takes a 25MHz crystal input and produces
two pairs of differential outputs (HCSL) at 25MHz, 100MHz,
125MHz, 200MHz clock frequencies.
ÎÎ25MHz crystal or clock input frequency
ÎÎHCSL outputs, 0.8V Current mode differential pair
ÎÎJitter 35ps cycle-to-cycle (typ)
ÎÎRMS phase jitter 12kHz ~ 20MHz @ 100MHz - 0.32ps (typ)
ÎÎRMS phase jitter 12kHz ~ 20MHz @ 125MHz - 0.3ps (typ)
ÎÎIndustrial temperature range
ÎÎPackaging: (Pb-free and Green)
àà 16-pin TSSOP (L16)
Pin Configuration (16-Pin TSSOP)
Block Diagram
VDD
S0
CLK0
S1:S0
Control
Logic
2
NC
X1/CLK
CLK1
X1/CLK
25 MHz
crystal or clock X2
Pulling
Capacitors
S1
CLK0
Phase
Lock
Loop
X2
CLK1
Crystal
Driver
OE
GND
RR
GND
All trademarks are property of their respective owners.
NC
OE
14-0044
1
1
16
VDDX
2
15
CLK0
3
14
CLK0
4
13
GNDA
5
12
VDDA
6
11
CLK1
7
10
CLK1
8
9
IREF
www.pericom.comPI6LC48H02 Rev.C
04/07/2014
PI6LC48H02
PCIe® 3.0/2.0/1.0 Clock Generator with 2 HCSL Outputs
Pin Description
Pin # Pin Name
I/O Type
Description
1
S0
Input
Select pin 0 (Internal pull-up resistor). See Table 1.
2
S1
Input
Select pin 1 (Internal pull-up resistor). See Table 1.
3
NC
-
Do not connect
4
X1/CLK
Input
Crystal or clock input. Connect to a 25MHz crystal or single ended clock.
5
X2
Output
Crystal connection. Leave unconnected for clock input.
6
OE
Input
Output enable. Internal pull-up resistor.
7
GND
Power
Ground
8
NC
-
Do not connect
9
IREF
Output
Precision resistor attached to this pin is connected to the internal current reference.
10
CLK1
Output
HCSL compliment clock output
11
CLK1
Output
HCSL clock output
12
VDDA
Power
Connect to a +3.3V source.
13
GNDA
Power
Output and analog circuit ground.
14
CLK0
Output
HCSL compliment clock output
15
CLK0
Output
HCSL clock output
16
VDDX
Power
Connect to a +3.3V source.
Table 1: Output Select Table
S1
S0
CLK(MHz)
0
0
25
0
1
100
1
0
125
1
1
200
All trademarks are property of their respective owners.
14-0044
2
www.pericom.comPI6LC48H02 Rev.C
04/07/2014
PI6LC48H02
PCIe® 3.0/2.0/1.0 Clock Generator with 2 HCSL Outputs
Application Information
Output Structures
Decoupling Capacitors
Decoupling capacitors of 0.01μF should be connected between
each VDD pin and the ground plane and placed as close to the
VDD pin as possible.
IREF =2.3mA
6*IREF
Crystal
Use a 25MHz fundamental mode parallel resonant crystal with
less than 300PPM of error across temperature.
Crystal Capacitors
CL = Crystals's load capacitance in pF
Crystal Capacitors (pF) = (CL - 8) *2
R R=475 Ω
For example, for a crystal with 16pF load caps, the external effective crystal cap would be 16 pF. (16-8)*2=16.
See Output Termination
Sections
Current Source (IREF) Reference Resistor - R R
If board target trace impedance is 50Ω,
then R R = 475Ω providing an IREF of 2.32 mA. The output current (IOH) is 6*IREF.
Output Termination
The PCI Express differential clock outputs of the PI6LC48H02
are open source drivers and require an external series resistor
and a resistor to ground. These resistor values and their allowable locations are shown in detail in the PCI Express Layout
Guidelines section.
The PI6LC48H02 can be configured for LVDS compatible voltage levels. See the LVDS Compatible Layout Guidelines section.
All trademarks are property of their respective owners.
14-0044
3
www.pericom.comPI6LC48H02 Rev.C
04/07/2014
PI6LC48H02
PCIe® 3.0/2.0/1.0 Clock Generator with 2 HCSL Outputs
PCI Express Layout Guidelines
Common Recommendations for Differential Routing
Dimension or Value
Unit
L1 length, route as non-coupled 50Ω trace.
0.5 max
inch
L2 length, route as non-coupled 50Ω trace.
0.2 max
inch
L3 length, route as non-coupled 50Ω trace.
0.2 max
inch
RS
33
Ω
RT
49.9
Ω
Differential Routing on a Single PCB
Dimension or Value
Unit
L4 length, route as coupled microstrip 100Ω differential trace.
2 min to 16 max
inch
L4 length, route as coupled stripline 100Ω differential trace.
1.8 min to 14.4 max
inch
Differential Routing to a PCI Express connector
Dimension or Value
Unit
L4 length, route as coupled microstrip 100Ω differential trace.
0.25 min to 14 max
inch
L4 length, route as coupled stripline 100Ω differential trace.
0.225 min to 12.6 max
inch
PCI Express Device Routing
L1
L2
RS
L1’
L4
L4’
L2’
RS
RT
PI6LC48H02
Output
Clock
L3’
RT
PCI-Express
Load or
Connector
L3
Typical PCI Express (HCSL) Waveform
800 mV
0
tOR
250 ps
400 ps
0.525 V
0.175 V
All trademarks are property of their respective owners.
14-0044
tOF
0.525 V
0.175 V
4
www.pericom.comPI6LC48H02 Rev.C
04/07/2014
PI6LC48H02
PCIe® 3.0/2.0/1.0 Clock Generator with 2 HCSL Outputs
Application Information
LVDS Recommendations for Differential Routing
Dimension or Value
Unit
L1 length, route as non-coupled 50Ω trace.
0.5 max
inch
L2 length, route as non-coupled 50Ω trace.
0.2 max
inch
RP
100
Ω
RQ
100
Ω
RT
150
Ω
L3 length, route as 100Ω differential trace.
L3 length, route as 100Ω differential trace.
LVDS Device Routing
L1
L3
RQ
L3’
L1’
RT
PI6LC48H02
Clock
Output
All trademarks are property of their respective owners.
RT
L2’
14-0044
RP
L2
5
LVDS
Device
Load
www.pericom.comPI6LC48H02 Rev.C
04/07/2014
PI6LC48H02
PCIe® 3.0/2.0/1.0 Clock Generator with 2 HCSL Outputs
Maximum Ratings
(Above which useful life may be impaired. For user guidelines, not tested.)
Supply Voltage to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . 4.6V
All Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . -0.5V to VDD+0.5V
Ambient Operating Temperature . . . . . . . . . . . . . . . . . . . -40 to +85°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Soldering Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Note:
Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to
the device. This is a stress rating only and functional operation of the device at these or any other
conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect reliability.
ESD Protection (HBM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 V
Electrical Specifications
Recommended Operation Conditions
Parameter
Min.
Ambient Operating Temperature
Power Supply Voltage (measured in respect to GND)
Typ.
Max.
Unit
-40
+85
°C
+3.0
+3.6
V
DC Characteristics (VDD = 3.3V ±10%, TA = -40°C to +85°C)
Symbol
Parameter
VDD
Supply Voltage
Voltage(1)
Conditions
Min.
Typ.
Max.
Unit
3.0
3.3
3.6
V
OE, S0, S1
2.0
VDD +0.3
V
Input Low Voltage(1)
OE, S0, S1
GND -0.3
0.8
V
IIH
Input High Current
Vin = VDD
-5
5
IIL
Input Low Current
Vin = 0
-20
20
IDD
R L = 50Ω, CL = 2pF
115
mA
IDDOE
Operating Supply Current
OE = LOW
65
mA
CIN
Input Capacitance
@ 55MHz
7
pF
COUT
Output Capacitance
@ 55MHz
6
pF
LPIN
Pin Inductance
5
nH
ROUT
Output Resistance
VIH
Input High
VIL
CLK Outputs
3.0
µA
kΩ
Notes:
1. Single edge is monotonic when transitioning through region.
All trademarks are property of their respective owners.
14-0044
6
www.pericom.comPI6LC48H02 Rev.C
04/07/2014
PI6LC48H02
PCIe® 3.0/2.0/1.0 Clock Generator with 2 HCSL Outputs
HCSL Output AC Characteristics (VDD = 3.3V ±10%, TA = -40°C to +85°C)
Symbol
Parameter
FIN
Input Frequency
FOUT
Output Frequency
VOH
Output High Voltage (1,2)
VOL
Output Low Voltage(1,2)
VCPA
Crossing Point Voltage(1,2)
Absolute
VCN
Crossing Point Voltage
Variation over all edges
JCC
Jitter, Cycle-to-Cycle(1,3)
JPhase
JRMS2.0
Conditions
25
(1,2,4)
(Random)
tOR
Rise Time
tOF
100 MHz HCSL output @ VDD =
3.3V
660
800
-150
0
250
350
Max.
Unit
MHz
200
MHz
900
mV
mV
550
mV
140
mV
35
60
ps
100MHz
25MHz Xtal input, 12kHz - 20MHz
0.32
0.5
ps
125MHz
25MHz Xtal input, 12kHz - 20MHz
0.3
0.5
ps
3.1
ps
PCIe 2.0 Test Method @ 100MHz
Output
PCIe 2.0 RMS Jitter
PCIe 3.0 RMS Jitter
Typ.
25
RMS Phase Jitter,
JRMS3.0
Min.
PLL L-BW @ 2M & 5M 1st H3
1.42
3
ps
PLL L-BW @ 2M & 4M 1st H3
2.05
3
ps
PLL H-BW @ 2M & 5M 1st H3
0.45
1
ps
PLL H-BW @ 2M & 4M 1st H3
0.45
1
ps
From 0.175V to 0.525V
175
700
ps
Fall Time(1,2)
From 0.525V to 0.175V
175
700
ps
TSKEW
Skew between outputs
At Crossing Point Voltage
50
ps
TDUTY-CYCLE
Duty Cycle
55
%
TOE
Output Enable Time(5)
All outputs
10
μs
TOT
Output Disable Time
All outputs
10
μs
tSTABLE
Stabilization Time
(1,2)
45
(1,3)
(5)
From Power-up VDD =3.3V
3.0
ms
Notes:
1. RL = 50-Ohm with CL = 2 pF
2. Single-ended waveform
3. Differential waveform
4. Measured at the crossing point
5. CLK pins are tri-stated when OE is LOW
All trademarks are property of their respective owners.
14-0044
7
www.pericom.comPI6LC48H02 Rev.C
04/07/2014
PI6LC48H02
PCIe® 3.0/2.0/1.0 Clock Generator with 2 HCSL Outputs
Thermal Characteristics
Symbol
Parameter
Conditions
θJA
Thermal Resistance Junction to Ambient
Still air
θJC
Thermal Resistance Junction to Case
Min.
Typ.
Max.
Unit
90
°C/W
24
°C/W
Recomended Crystal Specification
Pericom recommends:
a) GC2500003 XTAL 49S/SMD(4.0 mm), 25M, CL=18pF, +/-30ppm
http://www.pericom.com/pdf/datasheets/se/GC_GF.pdf
b) FY2500107, SMD 5x3.2(4P), 25M, CL=18pF, +/-30ppm
http://www.pericom.com/pdf/datasheets/se/FY_F9.pdf
c) FL2500038, SMD 3.2x2.5(4P), 25M, CL=18pF, +/-20ppm
http://www.pericom.com/pdf/datasheets/se/FL.pdf
Phase Noise Plot
100MHz
All trademarks are property of their respective owners.
14-0044
125MHz
8
www.pericom.comPI6LC48H02 Rev.C
04/07/2014
PI6LC48H02
PCIe® 3.0/2.0/1.0 Clock Generator with 2 HCSL Outputs
Packaging Mechanical: 16-Pin TSSOP (L)
DATE: 05/03/12
Notes:
1. Refer JEDEC MO-153F/AB
2. Controlling dimensions in millimeters
3. Package outline exclusive of mold flash and metal burr
DESCRIPTION: 16-Pin, 173mil Wide TSSOP
PACKAGE CODE: L
DOCUMENT CONTROL #: PD-1310
Note:
12-0372
For
latest
REVISION: F
package info, please check: http://www.pericom.com/products/packaging/mechanicals.php
Ordering Information
Ordering Code
Package Code
Package Type
Operating Temperature
PI6LC48H02LIE
L
Pb-free & Green, 16-pin TSSOP
Industrial
Notes:
• Thermal characteristics can be found on the company web site at www.pericom.com/packaging/
• "E" denotes Pb-free and Green
• Adding an "X" at the end of the ordering code denotes tape and reel packaging
All trademarks are property of their respective owners.
14-0044
9
www.pericom.comPI6LC48H02 Rev.C
04/07/2014