ZOPT3100 Digital RGB/Ambient Light + Proximity Sensor IC Brief Description ALS Features The ZOPT3100 Sensor IC integrates an ambient light sensor (ALS), a color sensor (CS), and a proximity sensor (PS), as well as an LED driver on a single chip. The device is connected by an I²C™* interface to a microcontroller. Other I²C™ or SMBus devices can be connected to the same interface. The device has a programmable interrupt with hysteresis to respond to events and reduce the microcontroller tasks. Dynamic range : 0.006 lux to 32,000 lux ALS measurement uses CS green filtered values Temperature compensation CS/ALS output resolution: 14 to 18 bits Linear output code 50ms conversion rate for 14-bit resolution 50Hz/60Hz light flicker immunity Fluorescent light flicker immunity The device allows adjusting the brightness as well as the color of the display panel. This device can also measure distance in parallel with ALS and CS measurements in order to deactivate the touch screen during phone calls. CS Features Temperature compensation CS/ALS output resolution: 14 to 18 bits Linear output code 50ms conversion rate for 14-bit resolution 50Hz/60Hz light flicker immunity Fluorescent light flicker immunity Features 5 integrated photodiodes (1 proximity diode and 4 diodes for white, green, blue, and red channels) 5 analog-to-digital converters (ADCs) to measure PS in parallel to ALS/CS I²C™ capable of standard mode (100kHz) or fast mode (400kHz) communication; 1.8V logic compatible Programmable interrupt function for ALS (green channel) and PS with upper and lower thresholds PS measurement parallel to ALS/CS measurements Many measurement modes: PS+ALS+CS, ALS+CS, PS+ALS, PS only, ALS only, CS only Physical Characteristics Wide operation temperature: -40 to +90 °C Wide supply voltage: 2.4 to 3.6 V Low supply current: < 200µA (LED driver excluded) Low standby current: < 2µA ZOPT3100 Application Circuit VDD PS Features High ambient light suppression Built-in LED driver and detector Detection of movement (in/out) Cancelation of crosstalk (lowest PS value is stored and subtracted from output value to memorize the reflection quantity) Programmable pulsed LED driver: up to 125mA output current 11-bit resolution * I2C is a trademark of NXP. LED VDD 3.3V 3.3V VDD VDD SCL SDA INT PWM SCL SDA INT SEL AGND LED_GND ZOPT3100 VSS Microcontroller For more information, contact ZMDI via [email protected]. © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 1.01 — September 13, 2013. All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice. ZOPT3100 Digital RGB/Ambient Light + Proximity Sensor IC ZOPT3100 Block Diagram VDD 2.4 to 3.6V Regulator ADC Main State Machine Fuses ADC ADC ADC CS/ALS FSM Interrupt FSM Reference INT Register File SDA Bandgap I²C PS FSM SCL SEL Dual Slope ADC 11 Bit Applications Cellular phones POR Notebooks IR LED Consumer devices PWM OSC IR LED Driver LED GND AGND = Analog Block = Digital Block Ordering Information Product Sales Code Description Package ZOPT3100AC6B ZOPT3100 die — Temperature Range: -40 to +90 °C Unsawn wafer ZOPT3100 KIT ZOPT3100 Evaluation Kit, including Evaluation Board, cable, and 1 IC sample Kit Sales and Further Information www.zmdi.com [email protected] Zentrum Mikroelektronik Dresden AG Global Headquarters Grenzstrasse 28 01109 Dresden, Germany ZMD America, Inc. 1525 McCarthy Blvd., #212 Milpitas, CA 95035-7453 USA Central Office: Phone +49.351.8822.0 Fax +49.351.8822.600 USA Phone +855.275.9634 Phone +408.883.6310 Fax +408.883.6358 European Technical Support Phone +49.351.8822.7.772 Fax +49.351.8822.87.772 DISCLAIMER: This information applies to a product under development. Its characteristics and specifications are subject to change without notice. Zentrum Mikroelektronik Dresden AG (ZMD AG) assumes no obligation regarding future manufacture unless otherwise agreed to in writing. The information furnished hereby is believed to be true and accurate. However, under no circumstances shall ZMD AG be liable to any customer, licensee, or any other third party for any special, indirect, incidental, or consequential damages of any kind or nature whatsoever arising out of or in any way related to the furnishing, performance, or use of this technical data. ZMD AG hereby expressly disclaims any liability of ZMD AG to any customer, licensee or any other third party, and any such customer, licensee and any other third party hereby waives any liability of ZMD AG for any damages in connection with or arising out of the furnishing, performance or use of this technical data, whether based on contract, warranty, tort (including negligence), strict liability, or otherwise. European Sales (Stuttgart) Phone +49.711.674517.55 Fax +49.711.674517.87955 Zentrum Mikroelektronik Dresden AG, Japan Office 2nd Floor, Shinbashi Tokyu Bldg. 4-21-3, Shinbashi, Minato-ku Tokyo, 105-0004 Japan ZMD FAR EAST, Ltd. 3F, No. 51, Sec. 2, Keelung Road 11052 Taipei Taiwan Phone +81.3.6895.7410 Fax +81.3.6895.7301 Phone +886.2.2377.8189 Fax +886.2.2377.8199 Zentrum Mikroelektronik Dresden AG, Korea Office U-space 1 Building 11th Floor, Unit JA-1102 670 Sampyeong-dong Bundang-gu, Seongnam-si Gyeonggi-do, 463-400 Korea Phone +82.31.950.7679 Fax +82.504.841.3026 © 2013 Zentrum Mikroelektronik Dresden AG — Rev. 1.01— September 13, 2013. All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is subject to changes without notice.