RFX8051B Production Data Sheet CMOS 5GHz WLAN 802.11ac RFeIC WITH PA, LNA AND SPDT LEN RXEN GND ANT 16 15 14 13 Description NC 12 GND RX 11 NC NC 10 VDD VDD 9 NC 5 6 7 8 DET TXEN GND TX RFX8051B is a highly integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit) which incorporates key RF functionality needed for IEEE 802.11a/n/ac WLAN system operating in the 5.15-5.85GHz range. The RFX8051B architecture integrates a high-efficiency high-linearity power amplifier (PA), a low noise amplifier (LNA) with bypass, the associated matching network, LO rejection, and harmonic filters all in a CMOS single-chip device. RFX8051B has simple and low-voltage CMOS control logic, and requires minimal external components. A directional coupler based power detect circuit is also integrated for accurate monitoring of output power from the PA. RFX8051B is assembled in an ultra-compact low-profile 3.0x3.0x0.55 mm 16-lead QFN package, and is the ideal RF front-end solution for implementing 5GHz WLAN in smartphones and other platforms. Applications 802.11n/ac Wi-Fi Devices Tablets / MIDs Wi-Fi Media Gateways Consumer Electronics Notebook / Netbook / Ultrabook Access Points / Routers Set Top Boxes / Wireless IPTVs Other 5GHz ISM Platforms FEATURES 5GHz WLAN Single Chip, Single-Die RF Front-End IC Excellent ESD Protection on All Pins High Transmit Signal Linearity Meeting 802.11ac Standard RF Ports are free of DC Voltage All VDD Bias Pins have Internal RF Decoupling Separate TX, RX Transceiver Ports, Single Antenna Port Low Noise Figure for the Receive Chain 5GHz Power Amplifier with Low-Pass Harmonic Filter High Power Capability for Received Signals in Bypass Mode Full On-chip Matching Circuitry Low Noise Amplifier with Bypass Mode Minimal External Components Required Transmit/Receive Switch Circuitry 50-Ohm Input / Output Matching Integrated Power Detector for Transmit Power Monitor and Control Market Proven CMOS Technology 3mm x 3mm x 0.55mm Small Outline 16L QFN Package with Exposed Ground Pad RoHS and REACH Compliant Low Voltage CMOS Control Logic Low DC Power Consumption 1 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com RFX8051B Production Data Sheet PIN ASSIGNMENTS: Pin Number Pin Name Description 1, 3, 9, 11 NC Internally Not Connected – Can be connected to GND on PCB 2 RX Output RF Port from LNA or Bypass – DC Shorted to GND 4, 10 VDD DC Supply Voltage 5 DET Output Analog Voltage Proportional to the TX Antenna Power 6 TXEN CMOS Logic Input to Control TX Enable 7, 12, 14, 17 GND Ground – Must Be Connected to GND on the PCB 8 TX Input RF Port for TX Signals from the Transceiver – DC Shorted to GND 13 ANT Antenna Port RF Signal from the PA or RF Signal Applied to the LNA – DC Shorted to GND 15 RXEN CMOS Logic Input to Control RX Enable 16 LEN CMOS Logic Input to Control LNA Enable or Bypass Mode PIN-OUT DIAGRAM: LEN RXEN GND ANT 16 15 14 13 NC 12 GND 11 NC NC 10 VDD VDD 9 NC 17 GND RX 5 6 7 8 DET TXEN GND TX (Top “See-Through” View) 2 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com RFX8051B Production Data Sheet ABSOLUTE MAXIMUM RATINGS: Parameters Units Min Max Conditions DC VDD Voltage Supply V 0 3.9 All VDD Pins DC Control Pin Voltage V 0 3.6 All Control Pins Through VDD Pins when TX is “ON” DC VDD Current Consumption mA 400 TX RF Input Power dBm +7 ANT RF Input Power dBm +20 Bypass Mode ANT RF Input Power dBm +5 RX Mode Junction Temperature o C Storage Ambient Temperature o C -40 +150 Operating Ambient Temperature o C -40 +85 150 Appropriate care required according to JEDEC Standards Moisture Sensitivity MSL1 Note: Sustained operation at or above the Absolute Maximum Ratings for any one or combinations of the above parameters may result in permanent damage to the device and is not recommended. All Maximum RF Input Power Ratings assume 50-Ohm terminal impedance. NOMINAL OPERATING CONDITIONS: Parameters Units Min Typ Max Conditions DC VDD Voltage Supply (Note 1) V 3.0 3.3 3.6 All VDD Pins Control Voltage “High” (Note 2) V 1.2 3.3 Control Voltage “Low” V 0 0.3 DC Control Pin Current Consumption μA 1 DC Shutdown Current μA 3 PA Turn On/Off Time μsec 0.4 LNA Turn On/Off Time μsec 0.4 Shut-Down and “ON” State Switching Time μsec 0.4 RF Port Impedance ohms 50 ja (Note3) o C/W 46 jc o C/W 19 TX, RX, ANT – VDD Applied Note 1: For normal operation of the RFX8051B, VDD must be continuously applied to all VDD supply pins. Note 2: If control voltage can exceed 1.8V, a 10KΩ series resistor is recommended for the application circuit on each control line. 3 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com RFX8051B Production Data Sheet Note 3: For operation above +85 oC, use the ja as guidance for system design to assure the junction temperature will not exceed the maximum of +150 oC. TRANSMIT PATH CHARACTERISTICS (VDD=3.3V; T=+25oC) Parameters Units Min Typ Max Conditions Operating Frequency Band GHz 5.15 Linear Output Power for 802.11ac dBm +16 +16.5 EVM<1.8% MCS9 80MHz Linear Output Power for 802.11n dBm +17 +17.5 EVM<3% MCS7 40MHz Linear Output Power for 802.11a dBm +17.5 +18 EVM<3%, 64QAM 20MHz Mask Compliance for 802.11n dBm +19.5 +20.5 EVM<3% MCS0 40MHz Small-Signal Power Gain (Pin = -20dBm) dB 26 27 Between TX and ANT pins Power Gain Flatness dB -1 5.85 +1 Between TX and ANT pins 5.18GHz – 5.85GHz Output P1dB dBm +24 Between TX and ANT pins TX Quiescent Current mA 150 No RF Signal Applied TX Linear Current mA 210 POUT = +17dBm, 20 MHz Power Detector Voltage Output mV Second Harmonic 1500 POUT = +5 to +20dBm, 10kΩ Load dBc -40 POUT=+20dBm, CW Third Harmonic dBc -35 POUT=+20dBm, CW Input Return Loss dB -8 At TX Port Output Return Loss dB -8 At ANT Port Load VSWR for Stability (CW, Fixed Pin for Pout=+20dBm with 50Ω load) N/A 4:1 6:1 All non-harmonically related spurs less than -43dBm/MHz Load VSWR for Ruggedness (CW, Fixed Pin for Pout=+20dBm with 50 Ohm Load) N/A 8:1 10:1 No Damage 200 4 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com RFX8051B Production Data Sheet RECEIVE PATH CHARACTERISTICS (VDD=3.3V; T=+25oC) Parameters Units Min GHz 5.15 Gain dB 11.5 Noise Figure dB 2.8 Insertion Loss for LNA Bypass Mode dB 6 Between ANT and RX Pins; TXEN/LEN=”Low” -10 At ANT Port, LNA Mode Input Return Loss dB -15 LNA Bypass Mode -10 At RX Port, LNA Mode -10 LNA Bypass Mode 13 No RF Applied, Through VDD, LNA Mode 0.003 No RF Applied, Through VDD, LNA Bypass Mode -5 At ANT Pin, LNA Mode +16 At ANT Pin, LNA Bypass Mode Operating Frequency Band -8 -8 Output Return Loss dB DC Quiescent Current Typ Max Conditions 5.85 All RF Pins are Loaded by 50-Ohm Between ANT and RX pins, LNA Mode; RXEN=LEN=”High” 12.5 3.0 mA Input P1dB dBm At ANT Pin, LNA Mode CONTROL LOGIC TRUTH TABLE TXEN LEN RXEN Mode Of Operation 0 0 0 Shutdown 1 0 X Transmit Mode 0 1 1 LNA Receive Mode 0 0 1 LNA Bypass Mode Note: “1” denotes high voltage state (> 1.2V) “0” denotes low voltage state (<0.3V) at Control Pins “X” denotes the don’t care state 10KΩ series resistor may be required for each control line 5 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com RFX8051B Production Data Sheet PACKAGE DIMENSIONS (All Dimensions in mm): A A1 Dimensions( mm) Min Nom A 0.5 0.55 A1 0.00 b 0.20 0.25 D 2.95 3.00 D2 1.65 1.70 E 2.95 3.00 E2 1.65 1.70 e 0.45 0.50 L 0.35 0.40 b e D2 D Max 0.6 0.05 0.30 3.05 1.75 3.05 1.75 0.55 0.45 Pin 1 Mark E E2 L Pin 1 PCB LAND PATTERN PACKAGE MARKING: (With Recommended Thermal Vias) 0.25mm 0.5mm 0.25mm Pin 1 Mark 0.65mm 1.7mm 1.7mm 0.3mm drill (x9) 3.5mm 8051B LLLL.L First Line: Part Number UAYWW Third Line: Date Code Second Line: Wafer Lot 0.575mm 3.0mm 6 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com