RFX2402E Production Data Sheet CMOS 2.4GHZ TRANSMIT/RECEIVE WLAN RFeIC Description GND 17 VDD 16 GND 15 The RFX2402E is a fully integrated, single-chip, single-die RFeIC (RF Front-end Integrated Circuit) which incorporates all the RF functionality needed for today’s wireless communications. VDD DNC 14 13 The RFX2402E architecture integrates the PA, LNA, Transmit and Receive switching circuitry, the associated matching network, and a harmonic filter all in a CMOS single-chip device. 1 12 GND 2 11 GND 3 10 ANT This RFeIC is designed for use in 802.11b/g/n/ac applications operating at 2.4GHz. Combining superior performance, high sensitivity and efficiency, low noise, small form factor, and low cost, the RFX2402E is the ideal solution for single antenna applications, and the ideal building block for MIMO applications. 4 9 GND The RFX2402E has simple and low-voltage CMOS control logic, and requires minimal external components for system implementation. The PA power detector circuit is also integrated. RX GND GND TX 5 6 7 TXEN RXEN DET Applications 8 GND 802.11b/g/n/ac Multimedia Applications 802.11b/g/n/ac Embedded Applications 802.11b/g/n/ac Mobile Platforms 802.11b/g/n/ac NIC PC Card Other 2.4GHz ISM Radios 802.11b/g/n/ac Access Point FEATURES 2.4GHz ISM, Single Chip, Single-Die RF Front-End IC ESD Protection Circuitry on All Ports Separate TX and RX Transceiver Port and Single Antenna DC Decoupled RF Ports Port 2.4GHz Power Amplifier with Low-Pass Harmonic Filter Low Noise Amplifier Transmit/Receive Switch Circuitry High Transmit Signal Linearity Meeting Standards for OFDM and CCK modulation Integrated Power Detector for Transmit Power Monitor and Control Compatible with Low Voltage (1.2V) CMOS Control Logic or levels up to VDD Internal RF Decoupling on All VDD Bias Pins Low Noise Figure for Receive Channels High Power Capability for Received Signals Very Low DC Power Consumption Full On-chip Matching and Decoupling Circuitry Minimal External Components Required 50-Ohm Input / Output Matching Market Proven CMOS Technology 3mm x 3mm x 0.55mm Small Outline 16L-QFN Package with Exposed Ground Pad 1 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com RFX2402E Production Data Sheet PIN ASSIGNMENTS: Pin Number Pin Name Description 1 RX Received RF Signal from the LNA to the Transceiver; DC Shorted to GND 2, 3, 8, 9, 11,12, 15, 17 GND Ground – Must be connected to Ground in the Application Circuit 4 TX Transmitted RF signal from the Transceiver to the PA: DC Shorted to GND 5 TXEN CMOS Input to Enable the PA 6 RXEN CMOS Input to Enable the LNA 7 DET Analog Voltage Proportional to the PA Power Output 10 ANT Antenna port RF Signal from the PA or RF Signal Applied to the LNA; DC Shorted to GND 13 DNC Reserved pin, Do not connect in the Application Circuit 14, 16 VDD Voltage Supply Connection PINOUT DIAGRAM: RX 1 GND 2 GND TX VDD GND VDD DNC 16 15 14 13 12 GND 11 GND 3 10 ANT 4 9 GND 17 GND 5 6 7 8 TXEN RXEN DET GND (Top "See-Through" View) 2 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com RFX2402E Production Data Sheet ABSOLUTE MAXIMUM RATINGS: Parameters Units Min Max Conditions DC VDD Voltage Supply V 0 4.5 All VDD Pins DC Control Pin Voltage V 0 3.6 Through 1Kohm resistor Through VDD Pins when TX is “ON” DC VDD Current Consumption mA 350 DC Control Pin Current Consumption μA 1 TX RF Input Power dBm +10 All Operating Modes ANT RF Input Power dBm +5 When RX is “ON” Junction Temperature o C Storage Ambient Temperature o C +150 -50 No RF and DC Voltages Applied Appropriate care required according to JEDEC Standards +150 Note: Sustained operation at or above the Absolute Maximum Ratings for any one or combinations of the above parameters may result in permanent damage to the device and is not recommended. All Maximum RF Input Power Ratings assume 50-Ohm terminal impedance. NOMINAL OPERATING CONDITIONS: Parameters Units Min Typ Max Conditions DC VDD Voltage Supply V 2.7 3.3 3.6 All VDD Pins Control Voltage “High” (Note 1) V 1.2 Control Voltage “Low” V Through Series Resistor 0.3 DC Control Pin Current Consumption uA 1 DC Shutdown Current uA 2 PA Turn On/Off Time usec 0.5 LNA Turn On/Off Time usec 0.8 Shut-Down and “ON” State Switching Time usec 0.5 o Operating Ambient Temperature ja o C C/W -40 All Control Lines “Low” +125 35 See note 2 Note 1: If control voltage can exceed 1.8V, a 1KΩ – 10KΩ series resistor is recommended for the application circuit on each control line. Note2: For operation above +85 oC, use the ja as guidance for system design to assure the junction temperature will not exceed the maximum of +150 oC. 3 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com RFX2402E Production Data Sheet TRANSMIT TECHNICAL PARAMETERS (VDD=3.3V, T=+25 oC) Parameters Units Min Operating Frequency Band GHz 2.4 Output P1dB dBm +24 CW Linear Output Power 802.11b dBm +21 1Mbps CCK, Mask Compliance Linear Output Power 802.11n dBm +17 54Mbps OFDM, EVM< -33dB at ANT Linear Output Power 802.11g dBm +18 54Mbps OFDM, EVM<-30 dB at ANT Large-Signal Power Gain in All Modes dB 28 POUT = +18dBm Small-Signal Power Gain in All Modes dB 28.5 TX Quiescent Current mA 80 No RF Applied TX Linear Current mA 140 POUT = +18dBm V 0.25-1.6 Second Harmonic (CW) dBc -30 POUT = +20dBm, CW at ANT Pin Third Harmonic (CW) dBc -35 POUT = +20dBm, CW at ANT Pin Modulated Second Harmonic dBm/MHz -26 POUT = +20dBm, 802.11n HT40 Modulated Third Harmonic dBm/MHz -30 POUT = +20dBm, 802.11n HT40 Input Return Loss dB -10 Output Return Loss dB -12 Input Output Impedance SingleEnded Ohm 50 TX Leakage to RX Port dBm -7 Power Detector Voltage Output Typ Max Conditions 2.5 All RF Pins Terminated by 50 Ohms POUT = 0dBm POUT = +5 to +20dBm POUT = +20dBm at ANT RECEIVE TECHNICAL PARAMETERS (VDD=3.3V, T=+25 oC) Parameters Operating Frequency Band Units Min GHz 2.4 Typ Max 2.5 Gain dB 11 Noise Figure dB 3 Input Return Loss dB -12 Output Return Loss dB -10 RF Port Impedance Ohm 50 RX Quiescent Current mA 9 Input P1dB dBm -5 Conditions All RF Pins are Terminated by 50 Ohm No RF Applied 4 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com RFX2402E Production Data Sheet CONTROL SIGNAL DIAGRAM: Don’t Care RXEN TXEN Shutdown Receive Transmit CONTROL LOGIC TRUTH TABLE: TXEN RXEN Operating Conditions 0 0 Shut-down 0 1 RX Active 1 X TX Active Note: “1” denotes high voltage state (> 1.2V) “0” denotes low voltage stage (<0.3V) at Control Pins “X” denotes the don’t care state 5 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com RFX2402E Production Data Sheet PACKAGE DIMENSIONS: A A1 Dimensions (mm) Min Nom A 0.5 0.55 A1 0.00 0.02 b 0.20 0.25 D 2.90 3.00 D2 1.65 1.70 E 2.90 3.00 E2 1.65 1.70 e 0.45 0.50 L 0.35 0.40 b e D2 D Max 0.6 0.05 0.30 3.10 1.75 3.10 1.75 0.55 0.45 Pin 1 Mark L E E2 Pin 1 PACKAGE MARKING 0.25mm 0.5mm 0.25mm 0.65mm Pin 1 Mark LLLL.L Second Line Lot Number 1.7 mm x 1.7mm 3.5mm 0.625mm ADYYWW 0.65mm 2402E First Line Part Number Third Line Date Code 3.0mm PCB LAND PATTERN 6 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com RFX2402E Production Data Sheet TAPE AND REEL INFORMATION: 7 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com