DATA SHEET SKY13582-676LF: 0.4 to 3.8 GHz SP3T Switch Applications Cellular systems 3G/4G LTE systems Pre- and post-PA switching RF1 Features RF2 Broadband frequency range: 0.4 to 3.8 GHz RF3 Very low insertion loss RFC High isolation: 25 dB at 2.7 GHz Integrated GPIO interface Logic and Supply No DC blocking capacitors required 203357-001 Lead (Pb)-free and RoHS-compliant VDD Small QFN (9-pin, 1.1 1.1 0.5 mm) package (MSL1, 260 C per JEDEC J-STD-020) VC1 VC2 Figure 1. SKY13582-676LF Block Diagram Description Skyworks Green™ products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of Green™, document number SQ04-0074. 1 VC1 8 VC2 7 VDD 2 RF2 9 GND 6 GND 3 RF1 4 RFC 5 RF3 The SKY13582-676LF is a single-pole, triple-throw (SP3T) switch. No external DC blocking capacitors are required on the RF paths as long as there is no DC voltage on the RF line. The switch can operate over the temperature range of −40 C to +85 C. Switching is controlled by two CMOS/TTL compatible control voltage inputs (VC1 and VC2). Depending on the logic voltage level applied to the control pin, the RFC pin is connected to one of three switched RF outputs (RF1, RF2, or RF3) by using a low insertion loss path, while the path between the RFC pin and the other RF pins is in isolation. The SKY13582-676LF is provided in a small 9-pin, 1.1 1.1 0.5 mm QFN package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional descriptions are provided in Table 1. 203357-002 Figure 2. SKY13582-676LF Pinout (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203357E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 28, 2016 1 DATA SHEET • SKY13582-676LF: 0.4 TO 3.8 GHz SP3T SWITCH Table 1. SKY13582-676LF Pin Descriptions1 Pin Name Description Pin Name Description 1 VC1 Control voltage 1 6 GND Ground 2 RF2 RF input/output port 2 7 VDD Supply voltage 3 RF1 RF input/output port 1 8 VC2 Control voltage 2 4 RFC RF common port 9 GND Ground 5 RF3 RF input/output port 3 1 Exposed pads must be grounded. Electrical and Mechanical Specifications The absolute maximum ratings of the SKY13582-676LF are provided in Table 2. Electrical specifications are provided in Table 3. Table 4 is the logic truth table. Tables 5 and 6 show the isolation matrix specifications. Table 2. SKY13582-676LF Absolute Maximum Ratings1 Parameter Symbol Condition Minimum Maximum Units 5.5 V Supply voltage VDD T = 25 C 2.35 Control voltages VC1, VC2 T = 25 C 0 RF input power RFIN CW, T = 25 C; 50 Operating case temperature TCASEMAX Storage temperature TSTG 3.1 V +35 dBm 40 +85 C 55 +150 C 1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 March 28, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203357E DATA SHEET • SKY13582-676LF: 0.4 TO 3.8 GHz SP3T SWITCH Table 3. SKY13582-676LF Electrical Specifications1 (1 of 2) (VDD = 2.85 v, TOP = +25 °C, Characteristic Impedance [Zo] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units 0.35 0.40 0.50 0.6 0.5 0.6 0.65 0.8 dB dB dB dB Small Signal Insertion loss (RFC to RF1-RF3) 2 IL 400 to 960 MHz 960 to 2170 MHz 2170 to 2700 MHz 2700 to 3800 MHz Isolation (RFC to RF1-RF3) ISO 400 to 960 MHz 960 to 2170 MHz 2170 to 2700 MHz 2700 to 3800 MHz 32 23 20 18 36 27 25 23 dB dB dB dB Isolation (TRXx to any Off TRXx ports [adjacent]) ISO 400 to 960 MHz 960 to 2170 MHz 2170 to 2700 MHz 2700 to 3800 MHz 32 23 20 15 35 25 23 18 dB dB dB dB Isolation (TRXx to any Off TRXx ports [non-adjacent]) ISO 400 to 960 MHz 960 to 2170 MHz 2170 to 2700 MHz 2700 to 3800 MHz 36 29 25 20 39 32 27 22 dB dB dB dB Return loss (RFC to RF1-RF3) RL 400 to 2700 MHz 2700 to 3800 MHz 14 10 20 15 dB dB Up to 3800 MHz +34 +35 dBm Large Signal 0.1dB compression point LTE/WCDMA harmonic, RF1, RF2 or RF3 to ANT, low band LTE/WCDMA harmonic, RF1, RF2 or RF3 to ANT, mid band LTE/WCDMA harmonic, RF1, RF2 or RF3 to ANT, high band Second order intermodulation product Third order intermodulation product Triple beat ratio Triple beat ratio P0.1dB 2fO, 3fO 2fo, 3fo 2fo, 3fo fO = 824 to 960 MHz PIN = +26 dBm, VSWR 1:1 −72 –66 dBm fO = 824 to 960 MHz PIN = +26 dBm, VSWR 5:1 −65 –60 dBm fO = 1710 to 1910 MHz PIN = +26 dBm, VSWR 1:1 −72 –60 dBm fO = 1710 to 1910 MHz PIN = +26 dBm, VSWR 5:1 −65 –59 dBm fO = 2170 to 2690 MHz PIN = +26 dBm, VSWR 1:1 −70 –62 dBm fO = 2170 to 2690 MHz PIN = +26 dBm, VSWR 5:1 −65 –59 dBm fO = 3400 to 3800 MHz PIN = + 26 dBm, VSWR 1:1 −65 –60 dBm fO = 3400 to 3800 MHz PIN = + 26 dBm, VSWR 5:1 −60 –55 dBm IIP2 Bands 1, 5, 7 Ftx: +24 dBm, Fbl:-15 dBm +103 +110 dBm IIP3 Bands 1, 5, 7 Ftx: +24 dBm, Fbl:-15 dBm +61 +66 dBm TBR 650 to 900 MHz, TX1 = TX2 = +21.5 dBm, Block= -30 dBm +51 +85 dBc 1710 to 2155 MHz, TX1 = TX2 = +21.5 dBm, Block= -30 dBm +51 +85 dBc TBR Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203357E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 28, 2016 3 DATA SHEET • SKY13582-676LF: 0.4 TO 3.8 GHz SP3T SWITCH Table 3. SKY13582-676LF Electrical Specifications1 (2 of 2) (VDD = 2.85 v, TOP = +25 °C, Characteristic Impedance [Zo] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units DC Operating Supply voltage VDD T = 25 C 2.45 2.85 4.8 V Control voltage high VC1 T = 25 C 1.35 1.8 3 V Control voltage low VC1 T = 25 C 0 0.4 V Supply current IDD T = 25 C 100 A Control current ICTL T = 25 C 1 A Switching speed tSW From one active state to another active state. 5 s Startup time tON From VDD off to VDD on 20 s 40 2 1 Performance is guaranteed only under the conditions listed in this table. 2 Insertion loss is measured with a series inductor added to the RFC line. Table 4. SKY13582-676LF Logic Truth Table Path VDD VC1 VC2 RFC to RF1 H H L RFC to RF2 H H H RFC to RF3 H L H Isolation H L L Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 March 28, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203357E DATA SHEET • SKY13582-676LF: 0.4 TO 3.8 GHz SP3T SWITCH Table 5. SKY13582-676LF Isolation Matrix ANT to OFF Arms Antenna to OFF Arm Frequency (MHz) ANT RF1 RF2 RF3 960 –51 –36 ANT 2170 –40 –29 ANT 2690 –37 –27 ANT 3800 –31 –23 ANT 960 –38 –34 ANT 2170 –30 –26 ANT 2690 –27 –24 ANT 3800 –23 –21 ANT 960 –34 –40 ANT 2170 –27 –33 ANT 2690 –25 –31 ANT 3800 –22 –27 Table 6. SKY13582-676LF Isolation Matrix ON Arms to OFF Arms Throw Frequency (MHz) RF1 RF2 RF3 RF1 960 –35 –48 RF1 2170 –28 –38 RF1 2690 –26 –35 RF1 3800 –23 –30 RF2 960 –37 –53 RF2 2170 –29 –41 RF2 2690 –26 –38 RF2 3800 –22 –32 RF3 960 –52 –49 RF3 2170 –39 –40 RF3 2690 –36 –38 RF3 3800 –29 –33 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203357E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 28, 2016 5 DATA SHEET • SKY13582-676LF: 0.4 TO 3.8 GHz SP3T SWITCH Evaluation Board Description Package and Handling Information The SKY13582-676LF Evaluation Board is used to test the performance of the SKY13582-676LF SP3T switch. An Evaluation Board schematic diagram is provided in Figure 3. An assembly drawing of the Evaluation Board is shown in Figure 4. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SKY13582-676LF is rated to Moisture Sensitivity Level 1 (MSL1) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Package Dimensions The PCB layout footprint for the SKY13582-676LF is provided in Figure 5. Typical part markings are shown in Figure 6. Package dimensions are shown in Figure 7, and tape and reel dimensions are provided in Figure 8. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. DC Control C2 DNI 1 VC1 DC Control C3 DNI C1 DNI RFC2 RFC1 DC Supply 7 VDD 8 VC2 2 RF2 9 GND 6 GND 3 RF1 4 RFC 5 RF3 GND RFC3 203357-003 L1 1.0 nH RFC4 Figure 3. SKY13582-676LF Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 March 28, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203357E DATA SHEET • SKY13582-676LF: 0.4 TO 3.8 GHz SP3T SWITCH DCH1 C2 C1 C3 U1 L1 RFC2 RF C3 C1 RFC4 RF Y2026 Figure 4. SKY13582-676LF Evaluation Board Assembly Diagram DCH1 C2 C1 C3 U1 L1 RFC2 RF C3 RFC4 C1 RF 203357-004 Figure 5. SKY13582-676LF PCB Layout Footprint Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203357E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 28, 2016 7 DATA SHEET • SKY13582-676LF: 0.4 TO 3.8 GHz SP3T SWITCH Pin 1 Indicator Skyworks Part Number: 0 = Zero First Character X = Q/Y Code Lot Code 203357-006 Figure 6. Typical Part Marking (Top View) Seating Plane C Pin 8 6X 0.400 1.10 Pin 1 Indicator Pin 1 Indicator Pin1 See Detail B −0.004 ~ 0.046 A B 0.400 Pitch 1.10 6X 0.400 0.05 C 2X See Detail A 2X 0.05 C 0.110 Ref 0.45 +0.045 –0.05 0.05 C Top View 0.05 C 8X 0.050 Exposed Pad Bottom View 3 9X Side View 0.2 ± 0.05 5X R0.030 0.2 ± 0.05 0.2 ± 0.05 Detail A Pin 1 Indicator 0.06 X 0.06 0.10 M C A B 5 5 0.2 ± 0.05 0.10 M C A B Scale: 100X 3X This Rotation 2X Rotated 180 º 1X Rotated 90 ºCW 1X Rotated 90 ºCCW Detail B Scale: 100X 1X This Rotation Notes: 1. Dimensions and tolerances per ASME Y14.5-1994. 2. All dimensions are in millimeters unless otherwise specified. 3. Coplanarity applies to the terminals and all other bottom surface metallization. 4. Plating requirement per source control drawing (SCD) 2504. 5. Dimension applies to metallized terminal. If the terminal has a radius on its end, the width dimension should not be measured in that radius area. 203357-007 Figure 7. SKY13582-676LF Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 March 28, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203357E 1.75 ± 0.10 4.0 ± 0.10 Pin 1 Ø1.50 0.25 ± 0.05 (T) +0.1 2.0 ± 0.05 B 3.5 ± 0.05 DATA SHEET • SKY13582-676LF: 0.4 TO 3.8 GHz SP3T SWITCH 1.29 ± 0.05 (Bo) 8.0 + 0.30 –0.10 R0.10 Max A A B 0.64 ± 0.05 (Ko) R0.3 Typ 4.0 ± 0.10 Ø0.50 Section B Min User Feed Direction Notes: 1. Carrier tape must meet all requirements of Skyworks GP01-D233 procurement spec for tape and reel shipping. 2. Carrier tape shall be black conductive polycarbonate or polystyrene. 3. Cover tape shall be transparent conductive material. 4. ESD-surface resistivity shall be ≤ 1 × 1010 Ω/square per EIA, JEDEC TNR specification. 5. 10-sprocket hole pitch cumulative tolerance: ±0.20 mm. 6. Ao and Bo measured on plane 0.30 mm above the bottom of the pocket. 7. All dimensions are in millimeters. 1.29 ± 0.05 (Ao) Section A 0.01–0.06 203357-008 Figure 8. SKY13582-676LF Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 203357E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 28, 2016 9 DATA SHEET • SKY13582-676LF: 0.4 TO 3.8 GHz SP3T SWITCH Ordering Information Model Name SKY13582-676LF: 0.4 to 3.8 GHz SP3T Switch Manufacturing Part Number SKY13582-676LF Evaluation Board Part Number EN37-D666-001 Copyright © 2014-2016 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 March 28, 2016 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 203357E