TWN4 Core Module Mifare™ NFC
125kHz/134.2kHz & 13.56MHz Contactless Reader/Writer
Bottom View
Top View
Elatec’s TWN4 Family allows users to read and write to almost any 125kHz / 134.2kHz and 13.56MHz tags and/or
labels – it supports all major transponders from various suppliers like ATMEL, EM, ST, NXP, TI, HID, LEGIC,
INSIDE etc. and ISO standards like ISO14443A including ISO14443A-4 (T=CL), ISO14443B including
ISO14443B-4 (T=CL), ISO15693, ISO18092 / ECMA-340 (NFC).
The TWN4 Core Module Mifare® NFC is designed for integration into machines or any other device to be used with
an external antenna (125/134.2kHz,13.56MHz or both). This core module mounted on an antenna carrier board is
available in the standard TWN Elatec desktop housing, too.
The powerful hardware allows the extension of supported transponders to meet your individual request.
Special Features:
Powerful SDK for writing Apps which are executed directly on the reader
Infield Upgradeable
Direct chip-commands support
Supports multiple SAMs (Secure Access Modules)1)
Supports 50 Ohm external antennas via SMA, SMB,SMC, MCX, UMCC/U.FL connectors
CCID and PC/SC 2.011)
Interfaces: USB, UART (5V CMOS TTL and RS232), I²C, SPI2), Clock/Data3), Wiegand3), CAN2)3)
Dedicated expansion bus for connection of LCD, mass storage…
Elatec GmbH
Lilienthalstr. 3
82178 Puchheim
+49 89 5529961 0
+49 89 5529961 29
[email protected]
Technical Data4)
Dimensions (L x W x H)
Power Supply
Current Consumption
Temperature Range
Read- / Write Distance
HOST Interface
OS Support
Transmission Speed
Modes of Operation
Relative Humidity
Order Code
125kHz, 134.2kHz (LF) / 13.56MHz (HF)
Externally, 50 Ohm for 13.56MHz – 490µH ±5% for 125kHz/134.2kHz
39mm x 30mm x 8mm / 1.54inch x 1.18inch x 0.31inch
3.3V+/-5% or (by using on-board voltage regulator) 4.3-5.5V
RF field off: 20mA /
Cyclic operation: 2mA1) /
Power down Mode: 10μA2)
RF field on: 120mA typically depending on antenna
Operating: -25°C up to +80°C (-13°F up to +176°F)
Storage: -45°C up to +85°C (-49°F up to +185°F)
Up to 100mm / 4inch, depending on antenna and tag
USB, RS232, serial 5V CMOS TTL, I²C, SPI2), Clock/Data3), Wiegand3), CAN2)3)
Windows Vista, XP, 7 (32-/64-bit), 8, Linux
HOST: USB: Full speed (12Mbit) – RS232: up to 115.200baud
AIR: up to 848Kbit/s
USB key board emulation – USB virtual COM port – Transparent – CCID and PC/SC 2.011)
5% to 95% non-condensing
 125kHz / 134.2kHz
4100, 4102, 42005), AWID, Casi Rusco, HITAG 16), HITAG 26), HITAG S6), Keri, MIRO, Pyramid,
Optionally, in consideration: 4305, Cardax, FDX-B, IDTECK, Q5, TITAN, T55x7, ZOODIAC
 13.56MHz / ISO14443A
Mifare Classic 1k & 4k, Mini, DESFire EV1, Plus S&X7), Pro X7), SmartMX7), Ultralight, Ultralight C,
SLE44R35, SLE66Rxx (my-d move)7), Legic Advant5), PayPass7)
 13.56MHz / ISO14443B
Calypso7), CEPAS7), HID iCLASS7), Moneo7), PicoPass7), SRI512, SRT512, SRI4K, SRIX4K
 13.56MHz / ISO18092 / NFC
NFCIP-1: Active and passive communication mode, Peer-to-Peer1), NFC Forum Tag Type 1-4,
Sony FeliCa6)
 13.56MHz / ISO15693
EM4x337), EM4x357), HID iCLASS5), ICODE SLI, Legic Advant5), M24LR16/64, Tag-It, SRF55Vxx (my-d
vicinity)7), PicoPass7)
Version P: Standard + Cotag, G-Prox8), HID Prox, Honeywell Nexwatch, Indala, ioProx
CE, R&TTE, RoHS-II compliant
500.000 hours
Approx. 7g
Standard: ART14194
Version P: ART14904
Preparation 2)On Request Only 3)External Interface Required 4)Target Specification 5)UID Only 6)Encryption Not Supported 7)UID/PUPI Only, Read/Write On Request 8)Hash Value Only
Drawing/Pin Out
Bottom View
Right View
Elatec reserves the right to change any information or data in this document without prior notice. The distribution and the update of this document is not controlled. Elatec declines all responsibility for
the use of product with any other specifications but the ones mentioned above. Any additional requirement for a specific customer application has to be validated by the customer himself at his own
responsibility. Where application information is given, it is only advisory and does not form part of the specification
© 2013 Elatec GmbH – DocRev5 – 07/2013
Elatec GmbH
Lilienthalstr. 3
82178 Puchheim
+49 89 5529961 0
+49 89 5529961 29
[email protected]