DATASHEET

HCTS540MS
Radiation Hardened
Inverting Octal Buffer/Line Driver, Three-State
September 1995
Features
Pinouts
• 3 Micron Radiation Hardened CMOS SOS
20 LEAD CERAMIC DUAL-IN-LINE
METAL SEAL PACKAGE (SBDIP)
MIL-STD-1835 CDIP2-T20, LEAD FINISH C
TOP VIEW
• Total Dose 200K RAD (Si)
• SEP Effective LET No Upsets: >100 MEV-cm2/mg
• Single Event Upset (SEU) Immunity < 2 x 10-9 Errors/
Bit-Day (Typ)
OE1
1
A0
2
19 OE2
A1
3
18 Y0
A2
4
17 Y1
A3
5
16 Y2
• Latch-Up Free Under Any Conditions
A4
6
15 Y3
• Fanout (Over Temperature Range)
- Bus Driver Outputs 15 LSTTL Loads
A5
7
14 Y4
A6
8
13 Y5
• Military Temperature Range: -55oC to +125oC
A7
9
12 Y6
GND 10
11 Y7
• Dose Rate Survivability: >1 x
10
• Dose Rate Upset >10
1012
RAD (Si)/s
RAD (Si)/s 20ns Pulse
20 VCC
• Significant Power Reduction Compared to LSTTL ICs
• DC Operating Voltage Range: 4.5V to 5.5V
• LSTTL Input Compatibility
- VIL = 0.8V Max
- VIH = VCC/2 Min
20 LEAD CERAMIC METAL SEAL
FLATPACK PACKAGE (FLATPACK)
MIL-STD-1835 CDFP4-F20, LEAD FINISH C
TOP VIEW
• Input Current Levels Ii ≤ 5µA at VOL, VOH
OE1
1
20
VCC
A0
2
19
OE2
A1
3
18
Y0
The Intersil HCTS540MS is a Radiation Hardened inverting
Octal Buffer/Line Driver, with two active-low output enables.
The output enable pins (OE1 and OE2) control the threestate outputs. If either enable is high the outputs will be in
the high impedance state. For data output both enables
(OE1 and OE2) must be low.
A2
4
17
Y1
A3
5
16
Y2
A4
6
15
Y3
A5
7
14
Y4
A6
8
13
Y5
A7
9
12
Y6
The HCTS540MS utilizes advanced CMOS/SOS technology
to achieve high-speed operation. This device is a member of
radiation hardened, high-speed, CMOS/SOS Logic Family.
GND
10
11
Y7
Description
The HCTS540MS is supplied in a 20 lead Ceramic flatpack
(K suffix) or a SBDIP Package (D suffix).
Ordering Information
PART NUMBER
TEMPERATURE RANGE
SCREENING LEVEL
PACKAGE
HCTS540DMSR
-55oC to +125oC
Intersil Class S Equivalent
20 Lead SBDIP
HCTS540KMSR
-55oC to +125oC
Intersil Class S Equivalent
20 Lead Ceramic Flatpack
HCTS540D/Sample
+25oC
Sample
20 Lead SBDIP
HCTS540K/Sample
+25oC
Sample
20 Lead Ceramic Flatpack
HCTS540HMSR
+25oC
Die
Die
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
1
Spec Number
File Number
518631
2232.2
HCTS540MS
Functional Diagram
ONE OF 8 BUFFERS
A0 2
A INPUTS
(2 - 9)
18 Y0
Y OUTPUTS
(18 - 11)
OE
TO OTHER
7 BUFFERS
OE1 1
OE2 19
TRUTH TABLE
H
L
X
Z
OE1
OE2
AN
OUTPUT
L
L
L
H
L
L
H
L
H
X
X
Z
X
H
X
Z
= High Level
= Low Level
= Don’t Care
= High Impedance
Spec Number
2
518631
Specifications HCTS540MS
Absolute Maximum Ratings
Reliability Information
Supply Voltage (VCC). . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V
Input Voltage Range, All Inputs . . . . . . . . . . . . .-0.5V to VCC +0.5V
DC Input Current, Any One Input . . . . . . . . . . . . . . . . . . . . . . . .±10mA
DC Drain Current, Any One Output. . . . . . . . . . . . . . . . . . . . . . .±25mA
(All Voltage Reference to the VSS Terminal)
Storage Temperature Range (TSTG) . . . . . . . . . . . -65oC to +150oC
Lead Temperature (Soldering 10sec) . . . . . . . . . . . . . . . . . . +265oC
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1
Thermal Resistance
θJA
θJC
SBDIP Package. . . . . . . . . . . . . . . . . . . .
72oC/W
24oC/W
Ceramic Flatpack Package . . . . . . . . . . . 107oC/W 28oC/W
Maximum Package Power Dissipation at +125oC Ambient
SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.69W
Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . . . . 0.47W
If device power exceeds package dissipation capability, provide heat
sinking or derate linearly at the following rate:
SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9mW/oC
Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . 9.3mW/oC
CAUTION: As with all semiconductors, stress listed under “Absolute Maximum Ratings” may be applied to devices (one at a time) without resulting in permanent
damage. This is a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The conditions listed
under “Electrical Performance Characteristics” are the only conditions recommended for satisfactory device operation.
Operating Conditions
Supply Voltage (VCC). . . . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V
Operating Temperature Range (TA) . . . . . . . . . . . . -55oC to +125oC
Input Rise and Fall Times at 4.5V VCC (TR, TF) . . . . . . 500ns Max.
Input Low Voltage (VIL). . . . . . . . . . . . . . . . . . . . . . . . . 0.0V to 0.8V
Input High Voltage (VIH) . . . . . . . . . . . . . . . . . . . . . . .VCC/2 to VCC
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETER
Quiescent Current
Output Current
(Sink)
Output Current
(Source)
Output Voltage Low
Output Voltage High
Input Leakage
Current
Three-State Output
Leakage Current
Noise Immunity
Functional Test
GROUP
A SUBGROUPS
TEMPERATURE
MIN
MAX
UNITS
1
+25oC
-
40
µA
2, 3
+125oC, -55oC
-
750
µA
1
+25oC
7.2
-
mA
2, 3
+125oC, -55oC
6.0
-
mA
1
+25oC
-7.2
-
mA
2, 3
+125oC, -55oC
-6.0
-
mA
VCC = 4.5V, VIH = 2.25V,
IOL = 50µA, VIL = 0.8V
1, 2, 3
+25oC, +125oC, -55oC
-
0.1
V
VCC = 5.5V, VIH = 2.75V,
IOL = 50µA, VIL = 0.8V
1, 2, 3
+25oC, +125oC, -55oC
-
0.1
V
VCC = 4.5V, VIH = 2.25V,
IOH = -50µA, VIL = 0.8V
1, 2, 3
+25oC, +125oC, -55oC
VCC
-0.1
-
V
VCC = 5.5V, VIH = 2.75V,
IOH = -50µA, VIL = 0.8V
1, 2, 3
+25oC, +125oC, -55oC
VCC
-0.1
-
V
VCC = 5.5V, VIN = VCC or
GND
1
+25oC
-
±0.5
µA
2, 3
+125oC, -55oC
-
±5.0
µA
1
+25oC
-
±1
µA
2, 3
+125oC, -55oC
-
±50
µA
7, 8A, 8B
+25oC, +125oC, -55oC
-
-
-
(NOTE 1)
CONDITIONS
SYMBOL
ICC
IOL
IOH
VOL
VOH
IIN
IOZ
FN
VCC = 5.5V,
VIN = VCC or GND
VCC = 4.5V, VIH = 4.5V,
VOUT = 0.4V, VIL = 0V
VCC = 4.5V, VIH = 4.5V,
VOUT = VCC - 0.4V,
VIL = 0V
VCC = 5.5V, Applied Voltage = 0V or VCC
VCC = 4.5V, VIH = 2.25V,
VIL = 0.8V (Note 2)
LIMITS
NOTES:
1. All voltages referenced to device GND.
2. For functional tests, VO ≥ 4.0V is recognized as a logic “1”, and VO ≤ 0.5V is recognized as a logic “0”.
Spec Number
3
518631
Specifications HCTS540MS
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETER
Data to Output
Enable to Output
(NOTES 1, 2)
CONDITIONS
SYMBOL
LIMITS
TEMPERATURE
MIN
MAX
UNITS
TPHL
VCC = 4.5V
9
+25oC
2
21
ns
TPLH
VCC = 4.5V
10, 11
+125oC, -55oC
2
25
ns
TPZL
VCC = 4.5V
9
+25oC
2
30
ns
10, 11
+125oC, -55oC
2
35
ns
9
+25oC
2
26
ns
10, 11
+125oC, -55oC
2
30
ns
9
+25oC
2
26
ns
10, 11
+125oC, -55oC
2
30
ns
TPZH
Disable to Output
GROUP
A SUBGROUPS
VCC = 4.5V
TPLZ,
TPHZ
VCC = 4.5V
NOTES:
1. All voltages referenced to device GND.
2. AC measurements assume RL = 500Ω, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = 3V.
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS
LIMITS
PARAMETER
SYMBOL
Capacitance Power
Dissipation
CPD
Input Capacitance
Output Transition
Time
CIN
TTHL,
TTLH
CONDITIONS
NOTES
TEMPERATURE
MIN
MAX
UNITS
1
+25oC
-
45
pF
1
+125oC, -55oC
-
50
pF
1
+25oC
-
10
pF
1
+125oC, -55oC
-
10
pF
1
+25oC
-
12
ns
1
+125oC, -55oC
-
18
ns
VCC = 5.0V, f = 1MHz
VCC = 5.0V, f = 1MHz
VCC = 4.5V
NOTE:
1. The parameters listed in Table 3 are controlled via design or process parameters. Min and Max Limits are guaranteed but not directly
tested. These parameters are characterized upon initial design release and upon design changes which affect these characteristics.
TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS
PARAMETER
Quiescent Current
SYMBOL
ICC
(NOTES 1, 2)
CONDITIONS
200K RAD
LIMITS
TEMPERATURE
MIN
MAX
UNITS
VCC = 5.5V, VIN = VCC or GND
+25oC
-
0.75
mA
6.0
-
mA
Output Current (Sink)
IOL
VCC = 4.5V, VIN = VCC or GND,
VOUT = 0.4V
+25oC
Output Current
(Source)
IOH
VCC = 4.5V, VIN = VCC or GND,
VOUT = VCC -0.4V
+25oC
-6.0
-
mA
Output Voltage Low
VOL
VCC = 4.5V or 5.5V, VIH = VCC/2,
VIL = 0.8V, IOL = 50µA
+25oC
-
0.1
V
Spec Number
4
518631
Specifications HCTS540MS
TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)
PARAMETER
(NOTES 1, 2)
CONDITIONS
SYMBOL
Output Voltage High
VOH
200K RAD
LIMITS
TEMPERATURE
MIN
MAX
UNITS
VCC = 4.5V or 5.5V, VIH = VCC/2,
VIL = 0.8V, IOH = -50µA
+25oC
VCC
-0.1
-
V
Input Leakage Current
IIN
VCC = 5.5V, VIN = VCC or GND
+25oC
-
±5
µA
Three-State Ouptut
Leakage Current
IOZ
VCC = 5.5V, Applied Voltage = 0V or VCC
+25oC
-
±50
µA
Noise Immunity
Functional Test
FN
VCC = 4.5V, VIH = 2.25V, VIL = 0.8V,
(Note 3)
+25oC
-
-
-
Data to Output
TPLH,
TPHL
VCC = 4.5V
+25oC
2
25
ns
Enable to Output
TPZL
VCC = 4.5V
+25oC
2
35
ns
TPZH
+25oC
2
30
ns
TPLZ,
TPHZ
+25oC
2
30
ns
Disable to Output
VCC = 4.5V
NOTES:
1. All voltages referenced to device GND.
2. AC measurements assume RL = 500Ω, CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = 3V.
3. For functional tests VO ≥ 4.0V is recognized as a logic “1”, and VO ≤ 0.5V is recognized as a logic “0”.
TABLE 5. BURN-IN AND OPERATING LIFE TEST, DELTA PARAMETERS (+25oC)
GROUP B
SUBGROUP
DELTA LIMIT
ICC
5
12µA
IOL/IOH
5
-15% of 0 Hour
IOZL/IOZH
5
±200nA
PARAMETER
TABLE 6. APPLICABLE SUBGROUPS
CONFORMANCE GROUPS
METHOD
GROUP A SUBGROUPS
Initial Test (Preburn-In)
100%/5004
1, 7, 9
ICC, IOL/H
Interim Test I (Postburn-In)
100%/5004
1, 7, 9
ICC, IOL/H
Interim Test II (Postburn-In)
100%/5004
1, 7, 9
ICC, IOL/H
PDA
100%/5004
1, 7, 9, Deltas
Interim Test III (Postburn-In)
100%/5004
1, 7, 9
PDA
100%/5004
1, 7, 9, Deltas
Final Test
100%/5004
2, 3, 8A, 8B, 10, 11
Sample/5005
1, 2, 3, 7, 8A, 8B, 9, 10, 11
Subgroup B-5
Sample/5005
1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas
Subgroup B-6
Sample/5005
1, 7, 9
Sample/5005
1, 7, 9
Group A (Note 1)
Group B
Group D
READ AND RECORD
Subgroups 1, 2, 3, 9, 10, 11,
(Note 2)
NOTES:
1. Alternate Group A testing in accordance with Method 5005 of MIL-STD-883 may be exercised.
2. Table 5 parameters only.
Spec Number
5
518631
Specifications HCTS540MS
TABLE 7. TOTAL DOSE IRRADIATION
TEST
CONFORMANCE
GROUPS
READ AND RECORD
METHOD
PRE RAD
POST RAD
PRE RAD
POST RAD
5005
1, 7, 9
Table 4
1, 9
Table 4 (Note 1)
Group E Subgroup 2
NOTE:
1. Except FN test which will be performed 100% Go/No-Go.
TABLE 8. STATIC BURN-IN AND DYNAMIC BURN-IN TEST CONNECTIONS
OSCILLATOR
OPEN
GROUND
1/2 VCC = 3V ± 0.5V
VCC = 6V ± 0.5V
50kHz
25kHz
-
20
-
-
-
1 - 9, 19, 20
-
-
11 - 18
20
1, 19
2-9
STATIC BURN-IN I TEST CONNECTIONS (Note 1)
11 - 18
1 - 10, 19
STATIC BURN-IN II TEST CONNECTIONS (Note 1)
11 - 18
10
DYNAMIC BURN-IN TEST CONNECTIONS (Note 2)
-
10
NOTES:
1. Each pin except VCC and GND will have a resistor of 10KΩ ± 5% for static burn-in.
2. Each pin except VCC and GND will have a resistor of 680Ω ± 5% for dynamic burn-in.
TABLE 9. IRRADIATION TEST CONNECTIONS
OPEN
GROUND
VCC = 5V ± 0.5V
11 - 18
10
1 - 9, 19, 20
NOTE: Each pin except VCC and GND will have a resistor of 47KΩ ± 5% for irradiation testing.
Group E, Subgroup 2, sample size is 4 dice/wafer 0 failures.
Spec Number
6
518631
HCTS540MS
Intersil Space Level Product Flow - ‘MS’
Wafer Lot Acceptance (All Lots) Method 5007
(Includes SEM)
100% Interim Electrical Test 1 (T1)
GAMMA Radiation Verification (Each Wafer) Method 1019,
4 Samples/Wafer, 0 Rejects
100% Static Burn-In 2, Condition A or B, 24 hrs. min.,
+125oC min., Method 1015
100% Nondestructive Bond Pull, Method 2023
100% Interim Electrical Test 2 (T2)
Sample - Wire Bond Pull Monitor, Method 2011
100% Delta Calculation (T0-T2)
Sample - Die Shear Monitor, Method 2019 or 2027
100% PDA 1, Method 5004 (Notes 1and 2)
100% Internal Visual Inspection, Method 2010, Condition A
100% Dynamic Burn-In, Condition D, 240 hrs., +125oC or
Equivalent, Method 1015
100% Delta Calculation (T0-T1)
100% Temperature Cycle, Method 1010, Condition C,
10 Cycles
100% Interim Electrical Test 3 (T3)
100% Constant Acceleration, Method 2001, Condition per
Method 5004
100% Delta Calculation (T0-T3)
100% PDA 2, Method 5004 (Note 2)
100% PIND, Method 2020, Condition A
100% Final Electrical Test
100% External Visual
100% Fine/Gross Leak, Method 1014
100% Serialization
100% Radiographic, Method 2012 (Note 3)
100% Initial Electrical Test (T0)
100% External Visual, Method 2009
100% Static Burn-In 1, Condition A or B, 24 hrs. min.,
+125oC min., Method 1015
Sample - Group A, Method 5005 (Note 4)
100% Data Package Generation (Note 5)
NOTES:
1. Failures from Interim electrical test 1 and 2 are combined for determining PDA 1.
2. Failures from subgroup 1, 7, 9 and deltas are used for calculating PDA. The maximum allowable PDA = 5% with no more than 3% of the
failures from subgroup 7.
3. Radiographic (X-Ray) inspection may be performed at any point after serialization as allowed by Method 5004.
4. Alternate Group A testing may be performed as allowed by MIL-STD-883, Method 5005.
5. Data Package Contents:
• Cover Sheet (Intersil Name and/or Logo, P.O. Number, Customer Part Number, Lot Date Code, Intersil Part Number, Lot Number,
Quantity).
• Wafer Lot Acceptance Report (Method 5007). Includes reproductions of SEM photos with percent of step coverage.
• GAMMA Radiation Report. Contains Cover page, disposition, Rad Dose, Lot Number, Test Package used, Specification Numbers, Test
equipment, etc. Radiation Read and Record data on file at Intersil.
• X-Ray report and film. Includes penetrometer measurements.
• Screening, Electrical, and Group A attributes (Screening attributes begin after package seal).
• Lot Serial Number Sheet (Good units serial number and lot number).
• Variables Data (All Delta operations). Data is identified by serial number. Data header includes lot number and date of test.
• The Certificate of Conformance is a part of the shipping invoice and is not part of the Data Book. The Certificate of Conformance is signed
by an authorized Quality Representative.
Spec Number
7
518631
HCTS540MS
AC Timing Diagrams
AC Load Circuit
VIH
DUT
INPUT
VS
TEST
POINT
VIL
CL
TPLH
RL
TPHL
VOH
VS
OUTPUT
CL = 50pF
VOL
RL = 500Ω
TTLH
VOH
TTHL
80%
20%
VOL
80%
20%
OUTPUT
AC VOLTAGE LEVELS
PARAMETER
HCTS
UNITS
VCC
4.50
V
VIH
3.00
V
VS
1.30
V
VIL
0
V
GND
0
V
Three-State Low Timing Diagrams
Three-State Low Load Circuit
VIH
VS
INPUT
VCC
VIL
RL
TPZL
TPLZ
VOZ
TEST
POINT
DUT
VT
VW
OUTPUT
CL
VOL
CL = 50pF
RL = 500Ω
THREE-STATE LOW VOLTAGE LEVELS
PARAMETER
HCTS
UNITS
VCC
4.50
V
VIH
3.00
V
VS
1.30
V
VT
1.30
V
VW
0.90
V
VIL
0
V
GND
0
V
Spec Number
8
518631
HCTS540MS
Three-State High Timing Diagrams
Three-State High Load Circuit
DUT
VIH
VS
TEST
POINT
INPUT
CL
VIL
RL
TPHZ
TPZH
VOH
VW
CL = 50pF
VT
OUTPUT
RL = 500Ω
VOZ
THREE-STATE HIGH VOLTAGE LEVELS
PARAMETER
HCTS
UNITS
VCC
4.50
V
VIH
3.00
V
VS
1.30
V
VT
1.30
V
VW
3.60
V
VIL
0
V
GND
0
V
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate
and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
Sales Office Headquarters
NORTH AMERICA
Intersil Corporation
P. O. Box 883, Mail Stop 53-204
Melbourne, FL 32902
TEL: (321) 724-7000
FAX: (321) 724-7240
EUROPE
Intersil SA
Mercure Center
100, Rue de la Fusee
1130 Brussels, Belgium
TEL: (32) 2.724.2111
FAX: (32) 2.724.22.05
ASIA
Intersil (Taiwan) Ltd.
Taiwan Limited
7F-6, No. 101 Fu Hsing North Road
Taipei, Taiwan
Republic of China
TEL: (886) 2 2716 9310
FAX: (886) 2 2715 3029
Spec Number
9
518631
HCTS540MS
Die Characteristics
DIE DIMENSIONS:
101 x 85mils
METALLIZATION:
Type: SiAl
Metal Thickness: 11kÅ ± 1kÅ
GLASSIVATION:
Type: SiO2
Thickness: 13kÅ ± 2.6kÅ
WORST CASE CURRENT DENSITY:
<2.0 x 105A/cm2
BOND PAD SIZE:
100µm x 100µm
4 mils x 4 mils
Metallization Mask Layout
HCTS540MS
A0
(2)
OE1
(1)
VCC
(20)
OE2
(19)
(18) Y0
A1 (3)
(17) Y1
A2 (4)
(16) Y2
A3 (5)
(15) Y3
A4 (6)
A5 (7)
(14) Y4
A6 (8)
(13) Y5
(9)
A7
(10)
GND
(11)
Y7
(12)
Y6
NOTE: The die diagram is a generic plot form a similar HCS device. It is intended to indicate approximate die size and bond pad location.
The mask series for the HCTS540 is TA14455A.
Spec Number
10
518631