Semiconductor Qualification Test Report: MESFET-D (QTR: 2013-00256)

Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
Report Title:
Qualification Test Report
Report Type:
See Attached
Date:
See Attached
QTR: 2013- 00256
Wafer Process: MESFET-D
HMC121
HMC132
HMC132
HMC147
HMC168
HMC173
Rev: 01
QTR: 2013- 00256
Wafer Process: MESFET-D
Rev: 01
Introduction
The testing performed for this report is designed to accelerate the predominant failure mode, electro-migration
(EM), for the devices under test. The devices are stressed at high temperature and DC biased to simulate a lifetime
of use at typical operating temperatures. Using the Arrhenius equation, the acceleration factor (AF) is calculated for
the stress testing based on the stress temperature and the typical use operating temperature.
This report is intended to summarize all of the High Temperature Operating Life Test (HTOL) data for the
MESFET-D process. The FIT/MTTF data contained in this report includes all the stress testing performed on this
process to date and will be updated periodically as additional data becomes available. Data sheets for the tested
devices can be found at www.hittite.com.
Glossary of Terms & Definitions:
1. HTOL: High Temperature Operating Life. This test is used to determine the effects of bias conditions and
temperature on semiconductor devices over time. It simulates the devices’ operating condition in an accelerated
way, through high temperature and/or bias voltage, and is primarily for device qualification and reliability
monitoring. This test was performed in accordance with JEDEC JESD22-A108.
2. Operating Junction Temp (T oj ): Temperature of the die active circuitry during typical operation.
3. Stress Junction Temp (T sj ): Temperature of the die active circuitry during stress testing.
QTR: 2013- 00256
Wafer Process: MESFET-D
Rev: 01
Qualification Sample Selection:
All qualification devices used were manufactured and tested on standard production processes and met pre-stress
acceptance test requirements.
Summary of Qualification Tests:
HMC128 (QTR02003)
TEST
QTY IN
QTY OUT
PASS/FAIL
Initial Electrical
33
33
Complete
HTOL, 620 hours
33
33
Complete
Post HTOL Electrical Test
33
33
Pass
Bond Pull
5
5
Pass
Die Shear
4
4
Pass
SEM Inspection
5
5
Pass
Metal and Dielectric Thickness
5
5
Pass
NOTES
QTR: 2013- 00256
Wafer Process: MESFET-D
Rev: 01
HMC129 (QTR02003)
TEST
QTY IN
QTY OUT
PASS/FAIL
Initial Electrical
12
12
Complete
HTOL, 1240 hours
12
12
Complete
Post HTOL Electrical Test
12
12
Pass
Bond Pull
5
5
Pass
Die Shear
4
4
Pass
SEM Inspection
5
5
Pass
Metal and Dielectric Thickness
5
5
Pass
QTY IN
QTY OUT
PASS/FAIL
Initial Electrical
35
35
Complete
HTOL, 620 hours
35
35
Complete
Post HTOL Electrical Test
35
35
Pass
Bond Pull
10
10
Pass
Die Shear
10
10
Pass
SEM Inspection
5
5
Pass
Metal and Dielectric Thickness
5
5
Pass
NOTES
HMC121 (QTR02006)
TEST
NOTES
QTR: 2013- 00256
Wafer Process: MESFET-D
Rev: 01
HMC182 (QTR02009)
TEST
QTY IN
QTY OUT
PASS/FAIL
Initial Electrical
20
20
Complete
HTOL, 1000 hours
20
20
Complete
Post HTOL Electrical Test
20
20
Pass
QTY IN
QTY OUT
PASS/FAIL
Initial Electrical
239
239
Complete
HTOL, 720 hours
239
239
Complete
Post HTOL Electrical Test
239
239
Pass
NOTES
HMC182 (QTR02009)
TEST
NOTES
QTR: 2013- 00256
Wafer Process: MESFET-D
Rev: 01
MESFET-D Failure Rate Estimate
Based on the HTOL test results, a failure rate estimation was determined using the following
parameters:
With Device Operating Temp = 85°C
HMC128 (QTR02003)
Operating Junction Temp (T oj ) =85°C(358°K)
Stress Junction Temp (T sj ) = 150°C(423°K)
HMC129 (QTR02003)
Operating Junction Temp (T oj ) =85°C(358°K)
Stress Junction Temp (T sj ) = 150°C(423°K)
HMC121 (QTR02006)
Operating Junction Temp (T oj ) =85°C(358°K)
Stress Junction Temp (T sj ) = 150°C(423°K)
HMC182 (QTR02009)
Operating Junction Temp (T oj ) =85°C(358°K)
Stress Junction Temp (T sj ) = 150°C(423°K)
HMC182 (QTR02009)
Operating Junction Temp (T oj ) =85°C(358°K)
Stress Junction Temp (T sj ) = 150°C(423°K)
Device hours:
HMC128 (QTR02003) = (33 X 620hrs) = 20,460 hours
HMC129 (QTR02003) = (12 X 1240hrs) = 14,880 hours
HMC121 (QTR02006) = (35 X 620hrs) = 21,700 hours
HMC182 (QTR02009) = (20 X 1000hrs) = 20,000 hours
HMC182 (QTR02009) = (239 X 720hrs) = 172,080 hours
For MESFET-D MMIC, Activation Energy = 1.6 eV
QTR: 2013- 00256
Wafer Process: MESFET-D
Rev: 01
Acceleration Factor (AF):
HMC128 (QTR02003) Acceleration Factor = exp[1.6/8.6 e-5(1/358-1/423)] = 2938.6
HMC129 (QTR02003) Acceleration Factor = exp[1.6/8.6 e-5(1/358-1/423)] = 2938.6
HMC121 (QTR02006) Acceleration Factor = exp[1.6/8.6 e-5(1/358-1/423)] = 2938.6
HMC182 (QTR02009) Acceleration Factor = exp[1.6/8.6 e-5(1/358-1/423)] = 2938.6
HMC182 (QTR02009) Acceleration Factor = exp[1.6/8.6 e-5(1/358-1/423)] = 2938.6
Equivalent hours = Device hours x Acceleration Factor
Equivalent hours = (20,460x2938.6)+(14,880x2938.6)+(21,700x2938.6)+ (20,000x2938.6)+(172,080x2938.6) =
1.68x108 hours
Since there were no failures and we used a time terminated test, F=0, and R = 2F+2 = 2
The failure rate was calculated using Chi Square Statistic:
at 60% and 90% Confidence Level (CL), with 0 units out of spec
and a 85°C package backside temp;
Failure Rate
λ 60 = [(χ2) 60 , 2 ]/(2X 1.68x108 )] = 1.8/ 3.36x108 = 5.46x10-9 failures/hour or 5.5 FIT or MTTF = 1.83x108 Hours
8
λ 90 = [(χ2) 90 , 2 ]/(2X 1.68x10 )] = 4.6/ 3.36x108 = 1.38x10-8 failures/hour or 13.8 FIT or MTTF = 7.27x107 Hours