^ϱ&Eϱ͘Ϭ ϮϬϬt^ƵƌĨĂĐĞDŽƵŶƚds^hŶŝͲĚŝƌĞĐƚŝŽŶĂů&Žƌ^Ͳϱ͘Ϭs PRIMARY CHARACTERISTICS 0603 200W VRWM,Max 5.0V IPP 13A VC 15.5V VBR,Min 6V TJ,Max 125℃ ● Body Marking Example Marking : T 1 2 1 2 T PPP PACKAGE Pin1 Pin2 FEATURES cathode anode MECHANICAL DATA IEC 61000-4-2 Level 4 ESD Case：Molded plastic,0603 protection. Polarity：Indicated by cathode band Low leakage current. Terminals : Golden Plated terminals, Moisture Sensitivity Level 1 solderable per MIL-STD-750,Method 2026 Epoxy : UL94-V0 rated flame retardant Maximum ratings (at T =25 C unless otherwise noted) o A PARAMETER Symbol CONDITIONS Peak pulse power tp = 8/20us P PP Peak pulse current tp = 8/20us I PP ESD per IEC 61000-4-2 Air discharge MIN. TYP. Operating junction temperature range TJ T STG Storage temperature range UNIT 200 W 13 A ±20 ESD Contact discharge MAX. ±15 -55 -55 KV +125 O C +150 O C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Electrical characteristics (at T =25 C unless otherwise noted, V o A V RWM(V) I R(uA) @V RWM Max. Max. 5.0 2.0 Part No. ESD5FN5.0 I T(mA) 1.0 F = 1.2V Max. @I F = 10mA) V BR(V) @I T V C(V) @I PP=13A C J (pF) @V R=0V,f=1MHz Min. Max. Max. 6.0 15.5 120 Over voltage available upon request. O 1. V BR is measured with a pulse test current I T at anambient temperature of 25 C. 2.Surge current waveform per Figure. 2015.0ϰ www.willas.com.tw Rev.&0ϭ P1 ^ϱ&Eϱ͘Ϭ ϮϬϬt^ƵƌĨĂĐĞDŽƵŶƚds^hŶŝͲĚŝƌĞĐƚŝŽŶĂů&Žƌ^Ͳϱ͘Ϭs Typical characteristics (at T =25 C unless otherwise noted) o A I IF V C V BR V RWM IR IT VF V I PP Uni-Directional TVS V C : Clamping Voltage @ I PP I PP : Maximum Reverse Peak Pulse Current V RWM : Maximum Reverse Working voltage I R : Maximum Reverse Leakage Current @V RWM V BR : Breakdown voltage @I T I T : Test Current P PP : Peak Pulse Power I F : Forward Current V F : Forward Voltage @ I F C J : Max. Capacitance @V R = 0V and f = 1MHz 2015.0ϰ www.willas.com.tw Rev.&0ϭ P2 ^ϱ&Eϱ͘Ϭ ϮϬϬt^ƵƌĨĂĐĞDŽƵŶƚds^hŶŝͲĚŝƌĞĐƚŝŽŶĂů&Žƌ^Ͳϱ͘Ϭs Rating and characteristic curves (ESD5FN5.0) FIG.2- POWER RATING DERATING CURVE 100 120 PEAK VALUE I RSM @8us tr 90 Mounting on glass epoxy PCBs 100 PULSE WIDTH(t P)IS DEFINED AS THAT POINT WHERE THE PEAK CURRENT DECAY = 8us 80 70 POWER RATING(%) % OF PEAK PULSE CURRENT FIG.1- 8 X 20us PULSE WAVEFORM 60 HALF VALUE = 50 I RSM 2 @20us 40 30 tP 20 80 60 40 20 10 0 0 20 40 80 60 t, TIME (us) 0 0 25 50 75 100 125 150 O AMBIENT TEMPERATURE( C) CAPACITANCE BETWEEN TERMINALS(pF) FIG.3- TERMINALS CHARACTERISTICS 120 f=1MHz TA=25 OC 100 80 60 40 20 0 0 1 2 3 4 5 REVERSE VOLTAGE(V) 2015.0ϰ www.willas.com.tw Rev.&0ϭ P3 ^ϱ&Eϱ͘Ϭ ϮϬϬt^ƵƌĨĂĐĞDŽƵŶƚds^hŶŝͲĚŝƌĞĐƚŝŽŶĂů&Žƌ^Ͳϱ͘Ϭs 0603 Outline Drawing 0.071(1.80) 0.063(1.60) 0.033(0.85) 0.029(0.75) 0.016(0.40)Typ. 0.014(0.35) Typ. 0.022(0.55) 0.018(0.45) 0.0236(0.60) Typ. Dimensions in inches and (millimeters) 2015.0ϰ www.willas.com.tw Rev.B Rev.&0ϭ P4 ^ϱ&Eϱ͘Ϭ ϮϬϬt^ƵƌĨĂĐĞDŽƵŶƚds^hŶŝͲĚŝƌĞĐƚŝŽŶĂů&Žƌ^Ͳϱ͘Ϭs 0603 Suggested Soldering Pad Layout .031(0.80) .019(0.50) .035(0.90) .031(0.80) .039(1.00) .071(1.80) .102(2.60) Dimensions in inches and (millimeters) 2015.0ϰ www.willas.com.tw RevA Rev.&0ϭ P5 ^ϱ&Eϱ͘Ϭ ϮϬϬt^ƵƌĨĂĐĞDŽƵŶƚds^hŶŝͲĚŝƌĞĐƚŝŽŶĂů&Žƌ^Ͳϱ͘Ϭs Packing information P0 P1 d E F T T A B W P D2 D1 T C W1 D unit:mm Symbol Tolerance Carrier width Carrier length A 0.1 1.00 B 0.1 1.80 Carrier depth C 0.1 0.65 Sprocket hole d 0.1 13" Reel outside diameter 13" Reel inner diameter 7" Reel outside diameter 7" Reel inner diameter Feed hole diameter Sprocket hole position D D1 D D1 D2 2.0 min 2.0 min 0.5 1.50 178.00 62.00 13.00 E 0.1 1.75 Punch hole position F 0.05 3.50 Punch hole pitch P 0.1 4.00 Sprocket hole pitch P0 0.1 4.00 Embossment center P1 0.05 2.00 Overall tape thickness T 0.1 0.23 Tape width W 0.1 8.00 Reel width W1 1.0 11.40 Item 0603 Note:Devices are packed in accor dance with EIA standar 481-D and specifications listed above. 2015.0ϰ www.willas.com.tw Rev.&0ϭ P6 ^ϱ&Eϱ͘Ϭ ϮϬϬt^ƵƌĨĂĐĞDŽƵŶƚds^hŶŝͲĚŝƌĞĐƚŝŽŶĂů&Žƌ^Ͳϱ͘Ϭs Ordering Information: Device PN ESD5FN5.0 ‐T(1) H(2)‐WS Packing Tape&Reel: 5 Kpcs/Reel Note: (1) Packing code, Tape & Reel Packing (2) Halogen free product for packing code suffix “H” ***Disclaimer*** WILLAS reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. WILLAS or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on WILLAS data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. WILLAS does not assume any liability arising out of the application or use of any product or circuit. This is the preliminary specification. WILLAS products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of WILLAS. Customers using or selling WILLAS components for use in such applications do so at their own risk and shall agree to fully indemnify WILLAS Inc and its subsidiaries harmless against all claims, damages and expenditures. 2015.0ϰ www.willas.com.tw Rev.&0ϭ P7