ADSP-BF561 EZ-KIT Lite Evaluation System Manual (Rev. 3.0)

ADSP-BF561 EZ-KIT Lite®
Evaluation System Manual
Revision 3.0, June 2006
Part Number
82-000811-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106
a
Copyright Information
©2006 Analog Devices, Inc., ALL RIGHTS RESERVED. This document
may not be reproduced in any form without prior, express written consent
from Analog Devices, Inc.
Printed in the USA.
Limited Warranty
The EZ-KIT Lite evaluation system is warranted against defects in materials and workmanship for a period of one year from the date of purchase
from Analog Devices or from an authorized dealer.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by implication or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, VisualDSP++, the VisualDSP++ logo, Blackfin,
the Blackfin logo, CROSSCORE, the CROSSCORE logo, EZ-KIT Lite,
and EZ-Extender are registered trademarks of Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.
Regulatory Compliance
The ADSP-BF561 EZ-KIT Lite evaluation system has been certified to
comply with the essential requirements of the European EMC directive
89/336/EEC (inclusive 93/68/EEC) and, therefore, carries the “CE”
mark.
The ADSP-BF561 EZ-KIT Lite evaluation system had been appended to
Analog Devices Development Tools Technical Construction File referenced “DSPTOOLS1” dated December 21, 1997 and was awarded CE
Certification by an appointed European Competent Body and is on file.
The EZ-KIT Lite evaluation system contains ESD
(electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate on the human
body and equipment and can discharge without
detection. Permanent damage may occur on devices
subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance
degradation or loss of functionality. Store unused
EZ-KIT Lite boards in the protective shipping
package.
CONTENTS
PREFACE
Purpose of This Manual ................................................................. xii
Intended Audience ......................................................................... xii
Manual Contents .......................................................................... xiii
What’s New in This Manual ........................................................... xiv
Technical or Customer Support ...................................................... xiv
Supported Processors ....................................................................... xv
Product Information ....................................................................... xv
MyAnalog.com .......................................................................... xv
Processor Product Information .................................................. xvi
Related Documents .................................................................. xvi
Online Technical Documentation ............................................ xvii
Accessing Documentation From VisualDSP++ .................... xviii
Accessing Documentation From Windows .......................... xviii
Accessing Documentation From Web ................................... xix
Printed Manuals ....................................................................... xix
VisualDSP++ Documentation Set ......................................... xix
Hardware Tools Manuals ...................................................... xix
Processor Manuals ................................................................. xx
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
v
CONTENTS
Data Sheets .......................................................................... xx
Notation Conventions ................................................................... xxi
USING ADSP-BF561 EZ-KIT LITE
Package Contents ......................................................................... 1-2
Default Configuration .................................................................. 1-3
Installation and Session Startup ..................................................... 1-5
Evaluation License Restrictions ..................................................... 1-7
Memory Map ............................................................................... 1-7
LEDs and Push Buttons .............................................................. 1-10
Audio Interface ........................................................................... 1-11
Video Interface ........................................................................... 1-12
Example Programs ...................................................................... 1-13
Flash Programmer Utility ............................................................ 1-13
Background Telemetry Channel .................................................. 1-14
ADSP-BF561 EZ-KIT LITE HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
External Bus Interface Unit ..................................................... 2-3
SPORT Audio Interface .......................................................... 2-3
SPI Interface ........................................................................... 2-3
Programmable Flags ................................................................ 2-4
PPI Interfaces ......................................................................... 2-6
Video Output (PPI1) .......................................................... 2-7
Video Input (PPI0) ............................................................. 2-8
vi
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
CONTENTS
UART Port .............................................................................. 2-8
Expansion Interface ................................................................. 2-8
JTAG Emulation Port .............................................................. 2-9
Jumper and DIP Switch Settings .................................................. 2-10
Video Configuration Switch (SW2) ....................................... 2-10
Boot Mode Switch (SW3) ...................................................... 2-11
Push Button Enable Switch (SW4) ......................................... 2-12
PPI Clock Select Switch (SW5) .............................................. 2-13
Test DIP Switches (SW10 and SW11) .................................... 2-13
Audio Enable Switch (SW12) ................................................ 2-13
SPIS1/SPISS Select (SW13) ................................................... 2-14
Video Encoder Clock Select Jumper (JP1) .............................. 2-14
UART Loop Jumper (P1) ....................................................... 2-14
LEDs and Push Buttons .............................................................. 2-15
Reset Push Button (SW1) ...................................................... 2-15
Programmable Flag Push Buttons (SW6–9) ............................ 2-16
Power LED (LED1) ............................................................... 2-16
Reset LED (LED2) ................................................................ 2-16
USB Monitor LED (ZLED3) ................................................. 2-17
User LEDs (LED5–12, LED13–20) ....................................... 2-17
Connectors ................................................................................. 2-18
Expansion Interface (J1–3) .................................................... 2-18
Audio (J4 and J5) .................................................................. 2-19
Video (J6) ............................................................................. 2-19
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
vii
CONTENTS
Power (J7) ............................................................................ 2-20
RS-232 (P2) ......................................................................... 2-20
SPORT1 (P3) ....................................................................... 2-20
SPI (P5) ................................................................................ 2-21
JTAG (ZP4) .......................................................................... 2-21
ADSP-BF561 EZ-KIT LITE BILL OF MATERIALS
ADSP-BF561 EZ-KIT LITE SCHEMATIC
Title Page ..................................................................................... B-1
Processor – External Memory Interface .......................................... B-2
Processor – Programmable Flags, SPI ............................................ B-3
Processor – PPI0 and PPI1 ............................................................ B-4
Flash Memory and SDRAM .......................................................... B-5
Audio Codec ................................................................................ B-6
Audio Out .................................................................................... B-7
Audio In ....................................................................................... B-8
Audio Encoder (Video Out) .......................................................... B-9
Video Decoder (Video In) ........................................................... B-10
Reset, Push Button Switches, UART ........................................... B-11
Extender Card Connectors .......................................................... B-12
Power ......................................................................................... B-13
Decoupling Caps ........................................................................ B-14
INDEX
viii
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
PREFACE
Thank you for purchasing the ADSP-BF561 EZ-KIT Lite®, Analog
Devices, Inc. evaluation system for Blackfin® processors.
Blackfin processors support a media instruction set computing (MISC)
architecture. This architecture is the natural merging of RISC, media
functions, and digital signal processing (DSP) characteristics. Blackfin
processors deliver signal-processing performance in a microprocessor-like
environment.
The evaluation board is designed to be used in conjunction with the VisualDSP++® development environment to test the capabilities of the
ADSP-BF561 Blackfin processors. The VisualDSP++ development environment gives you the ability to perform advanced application code
development and debug, such as:
• Create, compile, assemble, and link application programs written
in C++, C and ADSP-BF561 assembly
• Load, run, step, halt, and set breakpoints in application program
• Read and write data and program memory
• Read and write core and peripheral registers
• Plot memory
Access to the ADSP-BF561 processor from a personal computer (PC) is
achieved through a USB port or an optional JTAG emulator. The USB
interface gives unrestricted access to the ADSP-BF561 processor and the
evaluation board peripherals. Analog Devices JTAG emulators offer faster
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ix
communication between the host PC and target hardware. Analog Devices
carries a wide range of in-circuit emulation products. To learn more about
Analog Devices emulators and processor development tools, go to
http://www.analog.com/dsp/tools/.
ADSP-BF561 EZ-KIT Lite provides example programs to demonstrate
the capabilities of the evaluation board.
ADSP-BF561 EZ-KIT Lite installation is part of the VisuL The
alDSP++ installation. The EZ-KIT Lite is a licensed product that
offers an unrestricted evaluation license for the first 90 days. For
details about evaluation license restrictions after the 90 days, refer
to “Evaluation License Restrictions” on page 1-7 and the VisualDSP++ Installation Quick Reference Card.
The board features:
• Analog Devices ADSP-BF561 processor
D
D
256-pin mini-BGA package
30 MHz CLKIN oscillator
• Synchronous dynamic random access memory (SDRAM)
D
64 MB (16M x 16 bits x 2 chips)
• Flash memory
D
8 MB (4M x 16 bits)
• Analog audio interface
D
D
D
x
AD1836 A – Analog Devices 96 kHz audio codec
4 input RCA phono jacks (2 stereo channels)
6 output RCA phono jacks (3 stereo channels)
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Preface
• Analog video interface
D
D
ADV7183A video decoder w/ 3 input RCA phono jacks
ADV7179 video encoder w/ 3 output RCA phono jacks
• Universal asynchronous receiver/transmitter (UART)
D
D
ADM3202 RS-232 line driver/receiver
DB9 male connector
• LEDs
D
20 LEDs: 1 power (green), 1 board reset (red), 1 USB (red),
16 general purpose (amber), and 1 USB monitor (amber)
• Push buttons
D
5 push buttons with debounce logic: 1 reset,
4 programmable flags
• Expansion interface
D PPI0, PPI1,
SPI, EBIU, Timers11-0, UART,
programmable flags, SPORT0, SPORT1
• Other features
D
JTAG ICE 14-pin header
The EZ-KIT Lite board holds 8 MB of flash memory, which can be used
to store user-specific boot code, allowing the board to run as a stand-alone
unit. The board also holds 512-Mb SDRAM, which can be used at runtime. For more information see “Memory Map” on page 1-7.
interfaces with the AD1836A audio codec, facilitating creation of
audio signal processing applications. SPORT0 also attaches to an off-board
connector to allow communication with other serial devices. For information about SPORT0, see “SPORT Audio Interface” on page 2-3.
SPORT0
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
xi
Purpose of This Manual
The parallel peripheral interfaces (PPIs) of the processor connect to both a
video encoder and video decoder, facilitating creation of video signal processing applications. For information on how the board utilizes the
processor’s PPIs, see “PPI Interfaces” on page 2-6.
The UART of the processor connects to an RS-232 line driver and a DB9
male connector, allowing you to interface with a PC or other serial device.
For information about the UART, see “UART Port” on page 2-8.
Additionally, the EZ-KIT Lite board provides access to most of the processor’s peripheral ports. Access is provided in the form of a
three-connector expansion interface. For information about the expansion
interface, see “Expansion Interface” on page 2-8.
Purpose of This Manual
The ADSP-BF561 EZ-KIT Lite Evaluation System Manual provides
instructions for installing the product hardware (board). The text
describes the operation and configuration of the board components and
provides guidelines for running your own code on the ADSP-BF561
EZ-KIT Lite. Finally, a schematic and a bill of materials are provided as a
reference for future designs.
The product software installation is detailed in the VisualDSP++ Installation Quick Reference Card.
Intended Audience
The primary audience for this manual is a programmer who is familiar
with Analog Devices processors. This manual assumes that the audience
has a working knowledge of the appropriate processor architecture and
instruction set. Programmers who are unfamiliar with Analog Devices
processors can use this manual but should supplement it with other texts
xii
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Preface
(such as the ADSP-BF561 Blackfin Processor Hardware Reference and
Blackfin Processor Instruction Set Reference) that describe your target
architecture.
Programmers who are unfamiliar with VisualDSP++ should refer to the
VisualDSP++ online Help and user’s or getting started guides. For the
locations of these documents, see “Related Documents”.
Manual Contents
The manual consists of:
• Chapter 1, “Using ADSP-BF561 EZ-KIT Lite” on page 1-1
Describes the EZ-KIT Lite functionality from a programmer’s perspective and provides an easy-to-access memory map
• Chapter 2, “ADSP-BF561 EZ-KIT Lite Hardware Reference” on
page 2-1
Provides information on the EZ-KIT Lite hardware components.
• Appendix A, “ADSP-BF561 EZ-KIT Lite Bill Of Materials” on
page A-1
Provides a list of components used to manufacture the EZ-KIT
Lite board.
• Appendix B, “ADSP-BF561 EZ-KIT Lite Schematic” on page B-1
Provides the resources to allow EZ-KIT Lite board-level debugging
or to use as a reference design.
B now is part of the online Help. The PDF version of
L Appendix
the ADSP-BF561 EZ-KIT Lite Evaluation System Manual is located
in the Docs\EZ-KIT Lite Manuals folder on the installation CD.
Alternatively, the schematics can be found on the Analog Devices
Web site: www.analog.com/processors.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
xiii
What’s New in This Manual
What’s New in This Manual
This revision of the ADSP-BF561 EZ-KIT Lite Evaluation System Manual
has been updated for VisualDSP++ 4.5.
Technical or Customer Support
You can reach Analog Devices, Inc. Customer Support in the following
ways:
• Visit the Embedded Processing and DSP products Web site at
http://www.analog.com/processors/technicalSupport
• E-mail tools questions to
[email protected]
• E-mail processor questions to
[email protected] (World wide support)
[email protected] (Europe support)
[email protected] (China support)
• Phone questions to 1-800-ANALOGD
• Contact your Analog Devices, Inc. local sales office or authorized
distributor
• Send questions by mail to:
Analog Devices, Inc.
One Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
USA
xiv
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Preface
Supported Processors
This EZ-KIT Lite evaluation system supports the Analog Devices
ADSP-BF561 Blackfin embedded processors.
Product Information
You can obtain product information from the Analog Devices Web site,
from the product CD-ROM, or from the printed publications (manuals).
Analog Devices is online at www.analog.com. Our Web site provides information about a broad range of products—analog integrated circuits,
amplifiers, converters, and digital signal processors.
MyAnalog.com
MyAnalog.com is a free feature of the Analog Devices Web site that allows
customization of a Web page to display only the latest information on
products you are interested in. You can also choose to receive weekly
e-mail notifications containing updates to the Web pages that meet your
interests. MyAnalog.com provides access to books, application notes, data
sheets, code examples, and more.
Registration:
Visit www.myanalog.com to sign up. Click Register to use MyAnalog.com.
Registration takes about five minutes and serves as means for you to select
the information you want to receive.
If you are already a registered user, just log on. Your user name is your
e-mail address.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
xv
Product Information
Processor Product Information
For information on embedded processors and DSPs, visit our Web site at
www.analog.com/processors, which provides access to technical publications, data sheets, application notes, product overviews, and product
announcements.
You may also obtain additional information about Analog Devices and its
products in any of the following ways.
• E-mail questions or requests for information to
[email protected] (World wide support)
[email protected] (Europe support)
[email protected] (China support)
• Fax questions or requests for information to
1-781-461-3010 (North America)
+49-89-76903-157 (Europe)
Related Documents
For information on product related development software, see the following publications.
Table 1. Related Processor Publications
xvi
Title
Description
ADSP-BF561 Blackfin Embedded Symmetric Multi-Processor Datasheet
General functional description, pinout, and timing
ADSP-BF561 Blackfin Processor Hardware
Reference
Description of internal processor architecture and
all register functions
Blackfin Processor Instruction Set Reference
Description of all allowed processor assembly
instructions
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Preface
Table 2. Related VisualDSP++ Publications
Title
Description
VisualDSP++ User’s Guide
Description of VisualDSP++ features and usage
VisualDSP++ Assembler and Preprocessor
Manual
Description of the assembler function and commands
VisualDSP++ C/C++ Complier and
Library Manual for Blackfin Processors
Description of the complier function and commands for Blackfin processors
VisualDSP++ Linker and Utilities Manual
Description of the linker function and commands
VisualDSP++ Loader and Utilities Manual
Description of the loader/splitter function and commands
you plan to use the EZ-KIT Lite board in conjunction with a
L IfJTAG
emulator, also refer to the documentation that accompanies
the emulator.
All documentation is available online. Most documentation is available in
printed form.
Visit the Technical Library Web site to access all processor and tools manuals and data sheets:
http://www.analog.com/processors/resources/technicalLibrary.
Online Technical Documentation
Online documentation comprises the VisualDSP++ Help system, software
tools manuals, hardware tools manuals, processor manuals, the Dinkum
Abridged C++ library, and Flexible License Manager (FlexLM) network
license manager software documentation. You can easily search across the
entire VisualDSP++ documentation set for any topic of interest. For easy
printing, supplementary .pdf files of most manuals are provided in the
Docs folder on the VisualDSP++ installation CD.
Each documentation file type is described as follows.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
xvii
Product Information
File
Description
.chm
Help system files and manuals in Help format
.htm or
.html
Dinkum Abridged C++ library and FlexLM network license manager software documentation. Viewing and printing the .html files requires a browser, such as
Internet Explorer 5.01 (or higher).
.pdf
VisualDSP++ and processor manuals in Portable Documentation Format (PDF).
Viewing and printing the .pdf files requires a PDF reader, such as Adobe Acrobat
Reader (4.0 or higher).
If documentation is not installed on your system as part of the software
installation, you can add it from the VisualDSP++ CD at any time by running the Tools installation. Access the online documentation from the
VisualDSP++ environment, Windows® Explorer, or the Analog Devices
Web site.
Accessing Documentation From VisualDSP++
To view VisualDSP++ Help, click on the Help menu item or go to the
Windows task bar and navigate to the VisualDSP++ documentation via
the Start menu.
To view ADSP-BF561 EZ-KIT Lite Help, which is part of the VisualDSP++ Help system, use the Contents or Search tab of the Help
window.
Accessing Documentation From Windows
In addition to any shortcuts you may have constructed, there are many
ways to open VisualDSP++ online Help or the supplementary documentation from Windows.
Help system files (.chm) are located in the Help folder, and .pdf files are
located in the Docs folder of your VisualDSP++ installation CD-ROM.
The Docs folder also contains the Dinkum Abridged C++ library and the
FlexLM network license manager software documentation.
xviii
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Preface
Your software installation kit includes online Help as part of the Windows® interface. These help files provide information about VisualDSP++
and the ADSP-BF561 EZ-KIT Lite evaluation system.
Accessing Documentation From Web
Download manuals at the following Web site:
http://www.analog.com/processors/resources/technicalLibrary/manuals.
Select a processor family and book title. Download archive (.zip) files,
one for each manual. Use any archive management software, such as WinZip, to decompress downloaded files.
Printed Manuals
For general questions regarding literature ordering, call the Literature
Center at 1-800-ANALOGD (1-800-262-5643) and follow the prompts.
VisualDSP++ Documentation Set
To purchase VisualDSP++ manuals, call 1-603-883-2430. The manuals
may be purchased only as a kit.
If you do not have an account with Analog Devices, you are referred to
Analog Devices distributors. For information on our distributors, log onto
http://www.analog.com/salesdir/continent.asp.
Hardware Tools Manuals
To purchase EZ-KIT Lite and in-circuit emulator (ICE) manuals, call
1-603-883-2430. The manuals may be ordered by title or by product
number located on the back cover of each manual.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
xix
Product Information
Processor Manuals
Hardware reference and instruction set reference manuals may be ordered
through the Literature Center at 1-800-ANALOGD (1-800-262-5643),
or downloaded from the Analog Devices Web site. Manuals may be
ordered by title or by product number located on the back cover of each
manual.
Data Sheets
All data sheets (preliminary and production) may be downloaded from the
Analog Devices Web site. Only production (final) data sheets (Rev. 0, A,
B, C, and so on) can be obtained from the Literature Center at
1-800-ANALOGD (1-800-262-5643); they also can be downloaded from
the Web site.
To have a data sheet faxed to you, call the Analog Devices Faxback System
at 1-800-446-6212. Follow the prompts and a list of data sheet code
numbers will be faxed to you. If the data sheet you want is not listed,
check for it on the Web site.
xx
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Preface
Notation Conventions
Text conventions used in this manual are identified and described as
follows.
Example
Description
Close command
(File menu)
Titles in reference sections indicate the location of an item within the
VisualDSP++ environment’s menu system (for example, the Close
command appears on the File menu).
{this | that}
Alternative required items in syntax descriptions appear within curly
brackets and separated by vertical bars; read the example as this or
that. One or the other is required.
[this | that]
Optional items in syntax descriptions appear within brackets and separated by vertical bars; read the example as an optional this or that.
[this,…]
Optional item lists in syntax descriptions appear within brackets
delimited by commas and terminated with an ellipse; read the example
as an optional comma-separated list of this.
.SECTION
Commands, directives, keywords, and feature names are in text with
letter gothic font.
filename
Non-keyword placeholders appear in text with italic style format.
L
Note: For correct operation, ...
A Note provides supplementary information on a related topic. In the
online version of this book, the word Note appears instead of this
symbol.
a
Caution: Incorrect device operation may result if ...
Caution: Device damage may result if ...
A Caution identifies conditions or inappropriate usage of the product
that could lead to undesirable results or product damage. In the online
version of this book, the word Caution appears instead of this symbol.
[
Warning: Injury to device users may result if ...
A Warning identifies conditions or inappropriate usage of the product
that could lead to conditions that are potentially hazardous for the
devices users. In the online version of this book, the word Warning
appears instead of this symbol.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
xxi
Notation Conventions
conventions, which apply only to specific chapters, may
L Additional
appear throughout this document.
xxii
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
1 USING ADSP-BF561 EZ-KIT
LITE
This chapter provides specific information to assist you with development
of programs for the ADSP-BF561 EZ-KIT Lite evaluation system.
The information appears in the following sections.
• “Package Contents” on page 1-2
Lists the items contained in your ADSP-BF561 EZ-KIT Lite
package.
• “Default Configuration” on page 1-3
Shows the default configuration of the ADSP-BF561 EZ-KIT Lite.
• “Installation and Session Startup” on page 1-5
Instructs how to start a new or open an existing
ADSP-BF561EZ-KIT Lite session using VisualDSP++.
• “Evaluation License Restrictions” on page 1-7
Describes the restrictions of the VisualDSP++ demo license
shipped with the EZ-KIT Lite.
• “Memory Map” on page 1-7
Defines the ADSP-BF561 EZ-KIT Lite’s external memory map.
• “LEDs and Push Buttons” on page 1-10·
Describes the board’s LEDs and push buttons.
• “Audio Interface” on page 1-11
Describes the board’s audio interface.
• “Video Interface” on page 1-12
Describes the board’s video interface.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
1-1
Package Contents
• “Example Programs” on page 1-13
Provides information about the example programs included in the
ADSP-BF561 EZ-KIT Lite evaluation system.
• “Flash Programmer Utility” on page 1-13
Highlights the advantages of the Flash Programmer utility of
VisualDSP++.
• “Background Telemetry Channel” on page 1-14
Highlights the advantages of the Background Telemetry Channel
feature of VisualDSP++.
For information on the graphical user interface, including the boot loading, target options, and other facilities of the EZ-KIT Lite system, refer to
the online Help.
For more detailed information about programming the ADSP-BF561
Blackfin processor, see the documents referred to as “Related
Documents”.
Package Contents
Your ADSP-BF561 EZ-KIT Lite evaluation system package contains the
following items.
• ADSP-BF561 EZ-KIT Lite board
• VisualDSP++ Installation Quick Reference Card
• CD containing:
D
D
D
1-2
VisualDSP++ software
ADSP-BF561 EZ-KIT Lite software
USB driver files
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Using ADSP-BF561 EZ-KIT Lite
D
D
Example programs
ADSP-BF561 EZ-KIT Lite Evaluation System Manual (this
document)
• Universal 7V DC power supply
• USB 2.0 cable
• Registration card (please fill out and return)
If any item is missing, contact the vendor where you purchased your
EZ-KIT Lite or contact Analog Devices, Inc.
Default Configuration
The EZ-KIT Lite evaluation system contains ESD
(electrostatic discharge) sensitive devices. Electrostatic
charges readily accumulate on the human body and
equipment and can discharge without detection. Permanent damage may occur on devices subjected to
high-energy discharges. Proper ESD precautions are
recommended to avoid performance degradation or
loss of functionality. Store unused EZ-KIT Lite boards
in the protective shipping package.
The ADSP-BF561 EZ-KIT Lite board is designed to run outside your personal computer as a stand-alone unit. You do not have to open your
computer case.
When removing the EZ-KIT Lite board from the package, handle the
board carefully to avoid the discharge of static electricity, which may damage some components. Figure 1-1 shows the default jumper settings, DIP
switch, connector locations, and LEDs used in installation. Confirm that
your board is set up in the default configuration before using the board.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
1-3
Default Configuration
Figure 1-1. EZ-KIT Lite Hardware Setup
1-4
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Using ADSP-BF561 EZ-KIT Lite
Installation and Session Startup
correct operation, install the software and hardware in the
L For
order presented in the VisualDSP++ Installation Quick Reference
Card.
1. Verify that the yellow USB monitor LED (ZLED3, located near the
USB connector) is lit. This signifies that the board is communicating properly with the host PC and is ready to run VisualDSP++.
2. If you are running VisualDSP++ for the first time, navigate to the
VisualDSP++ environment via the Start –>Programs menu. The
main window appears. Note that VisualDSP++ does not connect to
any session. Skip the rest of this step to step 3.
If you have run VisualDSP++ previously, the last opened session
appears on the screen. You can override the default behavior and
force VisualDSP++ to start a new session by pressing and holding
down the Ctrl key while starting VisualDSP++. Do not release the
Ctrl key until the Session Wizard appears on the screen. Go to
step 4.
3. To connect to a new EZ-KIT Lite session, start Session Wizard by
selecting one of the following.
• From the Session menu, New Session.
• From the Session menu, Session List. Then click New Session from the Session List dialog box.
• From the Session menu, Connect to Target. Then click
New Session from the Session List dialog box.
4. The Select Processor page of the wizard appears on the screen.
Ensure Blackfin is selected in Processor family. In Choose a target
processor, select ADSP-BF561. Click Next.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
1-5
Installation and Session Startup
5. The Select Connection Type page of the wizard appears on the
screen. Select EZ-KIT Lite and click Next.
6. The Select Platform page of the wizard appears on the screen.
In the Select your platform list, select ADSP-BF561 EZ-KIT Lite
via Debug Agent. In Session name, highlight or specify the session
name.
The session name can be a string of any length; although, the box
displays approximately 32 characters. The session name can
include space characters. If you do not specify a session name,
VisualDSP++ creates a session name by combining the name of the
selected platform with the selected processor. The only way to
change a session name later is to delete the session and to open a
new session.
Click Next.
7. The Finish page of the wizard appears on the screen. The page displays your selections. If you are satisfied, click Finish. If not, click
Back to make changes.
disconnect from a session, click the disconnect button
L Toor select
Session –>Disconnect from Target.
To delete a session, select Session –> Session List. Select the session name from the list and click Delete. Click OK.
1-6
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Using ADSP-BF561 EZ-KIT Lite
Evaluation License Restrictions
The ADSP-BF561 EZ-KIT Lite installation is part of the VisualDSP++
installation. The EZ-KIT Lite is a licensed product that offers an unrestricted evaluation license for the first 90 days. Once the initial
unrestricted 90-day evaluation license expires:
• VisualDSP++ allows a connection to the ADSP-BF561 EZ-KIT
Lite via the USB Debug Agent interface only. Connections to simulators and emulation products are no longer allowed.
• The linker restricts a users program to 41 KB of internal memory
for code space with no restrictions for data space.
EZ-KIT Lite hardware must be connected and powered up to
L The
use VisualDSP++ with a valid evaluation or permanent license.
Refer to the VisualDSP++ Installation Quick Reference Card for details.
Memory Map
The EZ-KIT Lite board includes two types of external memory, 64-MB
SDRAM and 8-MB flash. See the external memory map in Table 1-1. The
complete configuration of the ADSP-BF561 processor internal SRAM is
detailed in Figure 1-2.
Table 1-1. EZ-KIT Lite External Memory Map
Start Address
End Address
Description
0x00000000
0x3FFFFFF
SDRAM bank 0; see “Memory Map” on page 1-7
0x20000000
0x207FFFFF
ASYNC memory bank 0; see “Memory Map” on page 1-7.
All other locations
Not used
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
1-7
Memory Map
CORE A MEMORY MAP
CORE B MEMORY MAP
0XFFFF FFFF
CORE MMR REGISTERS
0XFFE0 0000
SYSTEM MMR REGISTERS
0XFFC0 0000
0XFFB0 1000
0XFFB0 0000
0XFFA1 4000
0XFFA1 0000
0XFFA0 4000
0XFFA0 0000
0XFF90 8000
0XFF90 4000
0XFF90 0000
0XFF80 8000
0XFF80 4000
0XFF80 0000
RESERVED
L1 SCRATCHPAD SRAM (4K)
RESERVED
L1 INSTRUCTION SRAM/CACHE (16K)
RESERVED
L1 INSTRUCTION SRAM (16K)
L1 DATA BANK B SRAM (16K)
RESERVED
L1 DATA BANK A SRAM/CACHE (16K)
L1 DATA BANK A SRAM (16K)
RESERVED
L1 SCRATCHPAD SRAM (4K)
0XFF70 0000
RESERVED
0XFF61 4000
L1 INSTRUCTION SRAM/CACHE (16K)
0XFF61 0000
RESERVED
0XFF60 4000
0XFF50 8000
0XFF50 4000
0XFF50 0000
0XFF40 8000
0XFF40 4000
0XFF40 0000
0XFEB2 0000
0XFEB0 0000
0XEF00 0800
RESERVED
RESERVED
L1 DATA BANK B SRAM/CACHE (16K)
0XFF70 1000
0XFF60 0000
CORE MMR REGISTERS
RESERVED
L1 INSTRUCTION SRAM (16K)
RESERVED
L1 DATA BANK B SRAM/CACHE (16K)
L1 DATA BANK B SRAM (16K)
RESERVED
L1 DATA BANK A SRAM/CACHE (16K)
L1 DATA BANK A SRAM (16K)
RESERVED
L2 SRAM (128K)
RESERVED
Figure 1-2. ADSP-BF561 Processor Internal Memory Map
The 8 MB of flash memory is organized as 4M x 16 bit and mapped into a
ADSP-BF561 processor’s ASYNC memory bank 0. The ~AMS0 memory
select signal connects to the output enable pin of the flash memory.
The 64 MB of SDRAM is organized as 16M x 32 bits wide. The processor’s memory select pin ~SMS0 is configured for the SDRAM. Three
SDRAM control registers must be initialized in order to access the
SDRAM memory.
When in a VisualDSP++ EZ-KIT Lite session, you can configure the
SDRAM registers automatically by selecting the Use XML reset values
box on the Target Options dialog box, which is accessible through the
1-8
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Using ADSP-BF561 EZ-KIT Lite
Settings pull-down menu. The EBIU_SDGCTL, EBIU_SDBCTL, and
EBIU_SDRRC register values have been set in the ADSP-BF561.xml file found
in your VisualDSP\SYSTEM folder under the RegReset tag. These values can
be changed to be more optimal depending on the SCLK frequency.
The values in Table 1-2 are set by default whenever bank 0 is accessed
through the debugger (for example, when viewing memory windows or
loading a program). The numbers are derived for maximum flexibility and
work for a system clock frequency between 60 MHz and 133 MHz.
Table 1-2. EZ-KIT Lite Session SDRAM Default Settings
Register
Value
Function
EBIU_SDGCTL
0x0091998D
Calculated with SCLK = 133 MHz
EBIU_SDBCTL
0x00000013
EBIU_SDRRC
0x000001CF
Calculated with SCLK = 120 MHz
The EBIU_SDGCTL register can be written once after the processor comes
out of reset. Therefore, the user code should not re-initialize the register.
Clearing the Use XML reset values checkbox allows manual configuration
of the EBIU registers. For more information, see online Help.
Automatic configuration of the SDRAM is not optimized for a specific
frequency. Table 1-3 shows the optimized configuration of the
SDRAM registers using a 120 MHz SCLK. The frequency of 120 MHz is
the maximum SCLK frequency when using a 600 MHz core frequency, the
maximum frequency for the EZ-KIT Lite. Only the EBIU_SDRRC register
needs to be modified in the user code to achieve maximum performance.
SCLK
Table 1-3. SDRAM Optimum Settings1
Register
Value
EBIU_SDGCTL
0x0091998D
EBIU_SDBCTL
0x00000013
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
1-9
LEDs and Push Buttons
Table 1-3. SDRAM Optimum Settings1 (Cont’d)
Register
Value
EBIU_SDRRC
0x000003A0
1
Calculated with SCLK = 120 MHz
For more information, see “External Bus Interface Unit” on page 2-3.
program is included in the EZ-KIT installation direcL Antoryexample
to demonstrate the SDRAM interface setup.
LEDs and Push Buttons
The EZ-KIT Lite provides four push buttons and sixteen LEDs for general-purpose IO.
Sixteen LEDs, labeled LED5 through LED20, are controlled by the processor’s programmable flags PF32 through PF47 (equivalent to PPI0_D15–8
and PPI1_D15–8). These LEDs are accessed through the FLAG 2 registers.
First, the direction must be configured to output by setting the bits of the
FIO2_DIR register to 1. Then the value of the LEDs are modified using one
of the FIO2_FLAG_D, FIO2_FLAG_C, FIO2_FLAG_S, or FIO2_FLAG_T registers.
The four general-purpose push buttons are labeled SW6 through SW9. The
buttons connect to the programmable flags PF8–5. A status of each individual button can be read through the FIO0_FLAG_D register. A switch is
being pressed-on when the corresponding bit of the register reads 1. When
the switch is released, the bit reads 0. A connection between the push but-
1-10
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Using ADSP-BF561 EZ-KIT Lite
ton and PF input is established through the SW4 DIP switch. For
information on how to disconnect the switch from the programmable flag
and use it for another objective, see “Push Button Enable Switch (SW4)”.
program is included in the EZ-KIT installation direcL Antoryexample
to demonstrate the functionality of the LEDs and push
buttons.
Audio Interface
The AD1836A audio codec provides three channels of stereo audio output
and two channels of multichannel 96 kHz input. The SPORT0 interface of
the processor links with the stereo audio data input and output pins of the
AD1836A codec. The processor is capable of transferring data to the
audio codec in time-division multiplexed (TDM) or two-wire serial interface (TWI) mode.
In TWI mode, the codec can operate at a 96 kHz sample rate but restricts
the output to two channels. In TDM mode, the codec can operate at a
maximum of 48 kHz sample rate but allows simultaneous use of all input
and output channels. When using TWI mode, the TSCLK0 and RSCLK0 pins
(as well as the TFS0 and RFS0 pins of the processor) must be tied together
externally to the processor. This is accomplished with the SW4 DIP switch.
See “Push Button Enable Switch (SW4)” on page 2-12 for more
information.
The AD1836A audio codec’s internal configuration registers are configured using the processor’s PF4 programmable flag pin, used as the select
for the audio device. For more information on how to configure the multichannel codec, download the codec datasheet from the Analog Devices
Web site, www.analog.com.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
1-11
Video Interface
The AD1836A codec reset is controlled by the processor’s programmable
flag PF15. When PF15 is 0, the reset is asserted. When PF15 is 1, the reset is
de-asserted. Note that when PF15 is not driven (configured as input), the
AD1836A reset is asserted due to the pull-down resistor. See “Programmable Flags” on page 2-4 for more information.
programs are included in the EZ-KIT installation direcL Example
tory to demonstrate the AD1836A codec operation.
Video Interface
The board supports video input and output applications. The ADV7179
video encoder provides up to three output channels of analog video, while
the ADV7183A video decoder provides up to three input channels of analog video. The video encoder connects to the parallel peripheral
interface 1 (PPI1), while the video decoder connects to the parallel peripheral interface 0, (PPI0). Each PPI interface has an individual clock that is
configured by the SW5 switch settings. See “PPI Clock Select Switch
(SW5)” on page 2-13 for more information.
Both the encoder and the decoder connect to the parallel peripheral interfaces (PPI input clock) of the processor. For additional information on the
video interface hardware, refer to “PPI Interfaces” on page 2-6.
For the video interface to be operational, the following basic steps must be
performed.
1. Configure the SW2 DIP switch as required by the application. Refer
to “Video Configuration Switch (SW2)” on page 2-10 for details.
2. De-assert the video device’s reset by setting high a corresponding
programmable flag. PF14 controls the ADV7179 encoder’s reset,
while PF13 controls the ADV7183A decoder’s reset.
1-12
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Using ADSP-BF561 EZ-KIT Lite
3. If using the ADV7183A decoder:
D
D
Enable device by driving programmable flag output PF2 to 0.
Select PPI0 clock; for details, refer to “PPI Clock Select Switch
(SW5)” on page 2-13.
4. Program internal registers of the video device in use. Both video
encoder and decoder use a two-wire serial interface to access internal registers. The PF0 programmable flag functions as a serial clock
(SCL), and PF1 functions as a serial data (SDAT).
5. Program the ADSP-BF561 processor’s PPI interfaces (configuration registers, DMA, and so on).
programs are included in the EZ-KIT installation direcL Example
tory to demonstrate the capabilities of the video interface.
Example Programs
Example programs are provided with the ADSP-BF561 EZ-KIT Lite to
demonstrate various capabilities of the evaluation board. These programs
are installed with the EZ-KIT Lite software and can be found in the
…\Blackfin\Examples\ADSP-BF561 EZ-KIT Lite subdirectory of the VisualDSP++ installation directory. Please refer to the readme file provided
with each example for more information.
Flash Programmer Utility
The ADSP-BF561 EZ-KIT Lite evaluation system includes a Flash Programmer utility. The utility allows you to program the flash memory on
the EZ-KIT Lite. The Flash Programmer is installed with VisualDSP++.
Once the utility is installed, it is accessible from the Tools pull-down
menu.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
1-13
Background Telemetry Channel
The Flash Programmer driver is core-specific (core A) and must be loaded
to the core A in order to operate correctly. The Flash Programmer relies
on the user to set the correct core focus. To set up the correct core, select
the core A in the multiprocessor window before opening the Flash Programmer interface.
For more information on the Flash Programmer utility, refer to the online
Help.
Background Telemetry Channel
The ADSP-BF561 USB debug agent supports the background telemetry
channel (BTC), which facilitates data exchange between VisualDSP++ and
the processor without interrupting processor execution.
The BTC allows to view a variable as it is updated or changed, all while
the processor continues to execute. For increased performance of the
BTC, including faster reading and writing, please check out our latest line
of processor emulators at http://www.analog.com/processors/resources/crosscore/emulators/index.html. For more
information about the background telemetry channel, see the VisualDSP++ User’s Guide or online Help.
1-14
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
2 ADSP-BF561 EZ-KIT LITE
HARDWARE REFERENCE
This chapter describes the hardware design of the ADSP-BF561 EZ-KIT
Lite board. The following topics are covered.
• “System Architecture” on page 2-2
Describes the configuration of the ADSP-BF561 EZ-KIT Lite and
explains how the board components interface with the processor.
• “Jumper and DIP Switch Settings” on page 2-10
Shows the location and describes the function of the configuration
jumpers and switches.
• “LEDs and Push Buttons” on page 2-15
Shows the location and describes the function of the LEDs and
push buttons.
• “Connectors” on page 2-18
Shows the location and gives the part number for all of the connectors on the board. Also, the manufacturer and part number
information is given for the mating parts.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
2-1
System Architecture
System Architecture
This section describes the processor’s configuration on the EZ-KIT Lite
board.
Figure 2-1. System Architecture
This EZ-KIT Lite has been designed to demonstrate the capabilities of the
ADSP-BF561 Blackfin processor. The processor has an IO voltage of
3.3V. The core voltage and the core clock rate can be set on the fly by the
processor. The input clock is 30 MHz.
2-2
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Hardware Reference
External Bus Interface Unit
The external bus interface unit (EBIU) connects external memory to the
ADSP-BF561 processor. It includes a 32-bit wide data bus, an address bus
(A25–2), and a control bus. All of the 8-bit, 16-bit, and 32-bit accesses are
supported. On the EZ-KIT Lite board, the EBI unit connects to the
SDRAM and flash memory. For more information on using the external
memory see “Memory Map” on page 1-7.
All of the address, data, and control signals are available externally via the
expansion interface connectors (J1–3). The pinout of these connectors can
be found in “ADSP-BF561 EZ-KIT Lite Schematic” on page B-1.
SPORT Audio Interface
The SPORT0 interface connects to the AD1836A audio codec and the
expansion interface. The AD1836A codec uses both the primary and secondary data transmit and receive pins to input and output data from the
audio input and outputs.
The SPORT1 interface connects to the SPORT connector (P3).
The pinout of the SPORT and expansion interface connectors can be found
in “ADSP-BF561 EZ-KIT Lite Schematic” on page B-1.
SPI Interface
The processor’s serial peripheral interface (SPI) connects to the AD1836A
audio codec and the expansion interface. The SPI connection to the
AD1836A codec is used to access the control registers of the device. The
PF4 flag of the processor acts as the device select for the SPI port.
The SPI signals are available on the expansion interface and on the SPI
connector (P5). The pinout for the interface can be found in
“ADSP-BF561 EZ-KIT Lite Schematic” on page B-1.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
2-3
System Architecture
Programmable Flags
The processor has 48 programmable flag pins (PFs). Many of the flags are
multi-functional and depend on the processor’s setup. Table 2-1 shows
how the programmable flag pins are used on the EZ-KIT Lite.
Table 2-1. Programmable Flag Connections
Processor PF Pin Processor Function
2-4
EZ-KIT Lite Function
PF0
SPI select S, timer 0
Serial clock for programming ADV7179 video
encoder and ADV7183A video decoder.
PF1
SPI select 1, timer 1
Serial data for programming ADV7179 video
encoder and ADV7183A video decoder.
PF2
SPI select 2, timer 2
ADV7183A video decoder’s ~OE.
PF3
SPI select 3, timer 3
ADV7183A FIELD pin. See “Video Configuration
Switch (SW2)” on page 2-10.
PF4
SPI select 4, timer 4
AD1836A audio codec’s SPI select.
PF5
SPI select 5, timer 5
Push button (SW6). See “LEDs and Push Buttons” on
page 1-10 and “Push Button Enable Switch (SW4)”
on page 2-12 for information on how to disable the
push button.
PF6
SPI select 6, timer 6
Push button (SW7). See “LEDs and Push Buttons” on
page 1-10 and “Push Button Enable Switch (SW4)”
on page 2-12 for information on how to disable the
push button.
PF7
SPI select 7, timer 7
Push button (SW8). See “LEDs and Push Buttons” on
page 1-10 and “Push Button Enable Switch (SW4)”
on page 2-12 for information on how to disable the
push button.
PF8
Push button (SW9). See “LEDs and Push Buttons”
on page 1-10 and “Push Button Enable Switch
(SW4)” on page 2-12 for information on how to disable the push button.
PF9–12
Not used
PF13
ADV7183A video decoder’s reset
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Hardware Reference
Table 2-1. Programmable Flag Connections (Cont’d)
Processor PF Pin Processor Function
EZ-KIT Lite Function
PF14
ADV7179 video encoder’s reset
PF15
AD1836 codec’s reset
PF16
SPORT0
transmit frame sync pin
PF17
SPORT0
transmit data secondary pin
PF18
SPORT0
transmit data primary pin
PF19
SPORT0
receive frame sync pin
PF20
SPORT0
receive data secondary pin
PF21
SPORT1
transmit frame pin
PF22
SPORT1
transmit data secondary pin
PF23
SPORT1
transmit data primary pin
PF24
SPORT1
receive frame sync pin
PF25
SPORT1
receive data secondary pin
PF26
UART
transmit pin
PF27
UART
receive pin
PF28
SPORT0
receive serial clock pin
PF29
SPORT0
transmit serial clock pin
PF30
SPORT1
receive serial clock pin
PF31
SPORT1
transmit serial clock pin
PF39–32
PPI1
data 15–8
LED13–20
PF47–40
PPI0
data 15–8
LED5–12
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
2-5
System Architecture
PPI Interfaces
The ADSP-BF561 processor employs two independent parallel peripheral
interfaces (PPIs), PPI0 and PPI1. Each PPI interface is a half-duplex,
bi-directional bus consisting of 16 bits of data, a dedicated input clock,
and synchronization signals. The ADSP-BF561 EZ-KIT Lite board utilizes the PPI interfaces for video input and video output.
The PPI0 interface is configured to input video data from the ADV7183A
video decoder device: bits 7–0 connect to the video decoder’s data outputs.
The PPI1 interface is configured to output video data to the ADV7179
video encoder device: bits 7–0 connect to the video encoder’s data inputs.
Each PPI interface has a dedicated clock input configured independently
by the SW5 switch. The clock source can be one of the following: 27 MHz
crystal oscillator, ADV7183A video decoder’s clock output, or external
clock from the expansion interface. See “PPI Clock Select Switch (SW5)”
on page 2-13 for more information about the switch.
The SW2 switch provides a flexible connection between dedicated synchronization IOs (SYNC1 and SYNC2 of each PPI interface) and the encoder’s
and decoder’s horizontal and vertical synchronization pins. See “Video
Configuration Switch (SW2)” on page 2-10 for more information about
the switch. For a detailed description of the ADSP-BF561 processor’s PPI
interfaces, refer to the ADSP-BF561 Blackfin Processor Hardware Reference.
Table 2-2 describes the PPI pins of the EZ-KIT Lite board.
Table 2-2. PPI Connections
Processor PPI
Pin
EZ-KIT Lite Function
PPI0
bits 7–0
ADV7183A data outputs P15–8
PPI1
bits 7–0
ADV7179 data inputs P7–0
PPI0 SYNC1
2-6
Other Processor
Function
Timer 8
ADV7179 HSYNC. For more information, see “Video
Configuration Switch (SW2)” on page 2-10.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Hardware Reference
Table 2-2. PPI Connections (Cont’d)
Processor PPI
Pin
Other PRocessor
Function
EZ-KIT Lite Function
PPI0 SYNC2
Timer 9
ADV7179 VSYNC. For more information, see “Video
Configuration Switch (SW2)” on page 2-10.
PPI0
clock
A choice of ADV7183A output clock, a local 27 MHz
oscillator, or an external clock from
ADSP-BF533/BF561 EZ-KIT Extender® board.
PPI1 SYNC1
Timer 10
ADV7183A HSYNC. For more information, see “Video
Configuration Switch (SW2)” on page 2-10.
PPI1 SYNC2
Timer 11
ADV7183A VSYNC. For more information, see “Video
Configuration Switch (SW2)” on page 2-10.
PPI1
clock
A choice of ADV7183A output clock, a local 27 MHz
oscillator, or an external clock from
ADSP-BF53x/BF561 Blackfin EZ-Extender.
Video Output (PPI1)
The PPI1 interface is configured as output and connects to the on-board
video encoder device, ADV7179. The ADV7179 encoder generates three
analog video channels on DAC A, DAC B, and DAC C. The PPI1 bits 7–0 connect to P7–0 of the encoder’s pixel inputs. The encoder’s input clock is
fixed and comes from an on-board 27 MHz oscillator.
The encoder’s synchronization signals, HSYNC and VSYNC, can be configured as inputs or outputs. Video blanking control signal is at level 1. The
HSYNC and VSYNC signals can connect to SYNC1 and SYNC2 of the processor’s
PPI1 interface via the SW2 switch, as described in “Video Configuration
Switch (SW2)” on page 2-10.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
2-7
System Architecture
Video Input (PPI0)
The PPI0 interface is configured as input and connects to the on-board
video decoder device, ADV7183A. The ADV7183A decoder receives three
analog video channels on AIN1, AIN4, and AIN5 input. The decoder’s pixel
data outputs P15–8 drive the PPI0 inputs 8–0. The decoder’s 27 MHz pixel
clock output can be selected to drive any of the PPI clocks as shown in
Table 2-7 on page 2-13.
Synchronization outputs of the decoder, HS/HACTIVE, VS/VACTIVE, and
FIELD can connect to the processor’s PPI0_SYNC1, PPI0_SYNC2, and PF3
flag via the SW2 DIP switch, as described in “Video Configuration Switch
(SW2)” on page 2-10.
UART Port
The processor’s universal asynchronous receiver/transmitter (UART) port
connects to the ADM3202 RS-232 line driver as well as to the expansion
interface. The RS-232 line driver is attached to the DB9 male connector,
providing an interface to a personal computer and other serial devices.
Expansion Interface
The expansion interface consists of the three 90-pin connectors, J1–3.
Table 2-3 shows the interfaces each connector provides. For the exact
pinout of the connectors, refer to “ADSP-BF561 EZ-KIT Lite Schematic”
on page B-1. The mechanical dimensions of the connectors can be
obtained from Technical or Customer Support.
2-8
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Hardware Reference
Table 2-3. Connector Interfaces
Connector Interfaces
J1
5V, GND, address, data, PPI0 3–0, PF15–6, PF4
J2
3.3V, GND, SPI, NMI, PPI0 SYNC3–1, SPORT0, SPORT1, PF15–0, EBUI control signals
J3
5V, 3.3V, GND, UART, PPI1 15–0, reset, video control signals
Limits to the current and to the interface speed must be taken into consideration when using the expansion interface. The maximum current limit is
dependent on the capabilities of the used regulator. Additional circuitry
also can add extra loading to signals, decreasing their maximum effective
speed.
Devices does not support and is not responsible for the
[ Analog
effects of additional circuitry.
JTAG Emulation Port
The JTAG emulation port allows an emulator to access internal and external memories of the processor through a 6-pin interface. The JTAG
emulation port of the processor also connects to the USB debugging interface. When an emulator connects to the board at ZP4, the USB debugging
interface is disabled. See “JTAG (ZP4)” on page 2-21 for more information about the JTAG connector.
To learn more about available emulators, contact Analog Devices (see
“Product Information”).
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
2-9
Jumper and DIP Switch Settings
Jumper and DIP Switch Settings
This section describes functionality of the jumpers and DIP switches. The
jumper and DIP switch locations are shown in Figure 2-2.
Figure 2-2. DIP Switch Locations
Video Configuration Switch (SW2)
The video configuration switch (SW2) determines how some video signals
from the ADV7183A video decoder and ADV7179 video encoder are
routed to the processor’s PPIs. The switch also determines if the PF2 pin
controls the ~OE signal of the ADV7183A video decoder outputs. See
Table 2-4.
2-10
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Hardware Reference
Table 2-4. Video Configuration Switch (SW2)
Switch Position (Default)
Processor Signal
Video Signal
1 (OFF)
PPI1 SYNC1
ADV7179
2 (OFF)
PPI0 SYNC1
ADV7183A
3 (OFF)
PPI1 SYNC2
ADV7183A
4 (OFF)
PPI1 SYNC2
ADV7179
5 (OFF)
PF3 (FIELD)
ADV7183A
6 (ON)
PF2
ADV7183A
Positions 1 thorough 5 of SW2 determine how and if the SYNC1, SYNC2, and
FIELD control signals of the PPI0 and PPI1 interfaces are routed to the processor’s PPIs. In standard configuration of the encoder and decoder, this is
not necessary because the processor is capable of reading the control information embedded in the data stream.
Position 6 of SW2 determines whether PF2 connects to the ~OE signal of the
ADV7183A device. When the switch is OFF, PF2 can be used for other
operations, and the decoder output enable is held high with a pull-up
resistor.
Boot Mode Switch (SW3)
Positions 1 and 2 of the SW3 switch set the boot mode of the processor, as
described in Table 2-5. Position 3 sets the processor’s PLL on boot—
when the position is ON, the PLL is in bypass.
Table 2-5. Boot Mode Select Switch (SW3)
Position 1 BMODE0
Position 2 BMODE1
Boot Mode
ON
ON
Reserved
ON
OFF
Flash memory (default)
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
2-11
Jumper and DIP Switch Settings
Table 2-5. Boot Mode Select Switch (SW3) (Cont’d)
Position 1 BMODE0
Position 2 BMODE1
Boot Mode
OFF
ON
8-bit SPI PROM
OFF
OFF
16-bit SPI PROM
Push Button Enable Switch (SW4)
Positions 1 through 4 of the push button enable switch (SW4) allow to disconnect the drivers associated with the push buttons from the PF pins of
the processor. Positions 5 and 6 connect the transmit and receive frame
syncs and clocks of SPORT0. This is important when the AD1836A audio
codec and the processor are communicating in two-wire interface (TWI)
mode. Table 2-6 shows which PF is driven when the switch is ON.
Table 2-6. Push Button Enable Switch (SW4)
Switch Position
Default Setting
Pin #
Signal (Side 1)
Pin #
Signal (Side 2)
1
ON
1
SW6
12
PF5
2
ON
2
SW7
11
PF6
3
ON
3
SW8
10
PF7
4
ON
4
SW9
9
PF8
5
OFF
5
TFS0
8
RFS0
6
OFF
6
RSCLK0
7
TSCLK0
2-12
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Hardware Reference
PPI Clock Select Switch (SW5)
The SW5 switch controls a clock selection of the PPI interfaces as described
in Table 2-7 and Table 2-8.
Table 2-7. PPICLK1 Clock Source Setup
SW5 Position 1
PPI0_CKSEL0
SW5 Position 2
PPI0_CKSEL1
PPIxCLK1 Source
ON
ON
27 MHz oscillator (default)
OFF
ON
ADV7183 clock out
X
OFF
Expansion interface
Table 2-8. PPICLK2 Clock Source Setup
SW5 Position 3
PPI1_CKSEL0
SW5 Position 4
PPI1_CKSEL1
PPICLK2 Source
ON
ON
27 MHz oscillator (default)
OFF
ON
ADV7183 clock out
X
OFF
Expansion interface
Test DIP Switches (SW10 and SW11)
Two DIP switches (SW10 and SW11) are located on the bottom of the
board. The switches are used only for testing and should remain in the OFF
position.
Audio Enable Switch (SW12)
The audio enable switch (SW12) disconnects the audio signals from the
processor. The default is all positions ON.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
2-13
Jumper and DIP Switch Settings
SPIS1/SPISS Select (SW13)
The SPIS1/SPISS select switch (SW13) disconnects the SPIS1 and SPISS signals from the board, making them available on the SPI connector (P5).
The default is the ON position.
Video Encoder Clock Select Jumper (JP1)
The video encoder clock select jumper (JP1) determines the source of the
ADV7179 video encoder’s clock.
Table 2-9. Video Encoder Clock Select Jumper (JP1)
JP1 Position
Mode
1 and 2
Input clock for encoder is generated from 27 MHz oscillator (default)
2 and 3
Input clock for encoder is generated from output clock of decoder. This is
used when synchronizing the encoder and decoder clock is required.
UART Loop Jumper (P1)
The UART loop jumper (P1) is for looping the transmit and receive signals. The default is the OFF position.
2-14
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Hardware Reference
LEDs and Push Buttons
This section describes functionality of the LEDs and push buttons.
Figure 2-3 shows the locations of the LEDs and push buttons.
Figure 2-3. LED and Push Button Locations
Reset Push Button (SW1)
The RESET push button resets all of the ICs on the board. One exception is
the USB interface chip (U34). The chip is not being reset when the push
button is pressed after the USB cable has been plugged in and communication with the PC has been initialized correctly. Once communication is
initialized, the only way to reset the USB is by powering down the board.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
2-15
LEDs and Push Buttons
Programmable Flag Push Buttons (SW6–9)
Four push buttons, SW6–9, are provided for general-purpose user input.
The buttons connect to the programmable flag pins of the processor (PF5–
8). The push buttons are active high and, when pressed, send a high (1) to
the processor. Refer to “LEDs and Push Buttons” on page 1-10 for more
information on how to use PFs when programming the processor. The
push button enable switch (SW4) is capable of disconnecting the push buttons from its associated PF (refer to “Push Button Enable Switch (SW4)”
on page 2-12). The programmable flag pins and corresponding switches
are shown in Table 2-10.
Table 2-10. Programmable Flag Switches
Processor Programmable Flag Pin
Push Button Reference Designator
PF5
SW6
PF6
SW7
PF7
SW8
PF8
SW9
Power LED (LED1)
When LED1 is lit (green), it indicates that power is being supplied to the
board properly.
Reset LED (LED2)
When LED2 is lit, it indicates that the master reset of all major ICs is
active.
2-16
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Hardware Reference
USB Monitor LED (ZLED3)
The USB monitor LED (ZLED3) indicates that USB communication has
been initialized successfully and you can connect to the processor using a
VisualDSP++ EZ-KIT Lite session. This takes approximately 15 seconds.
If the LED does not light, try cycling power on the board and/or reinstalling the USB driver.
VisualDSP++ is actively communicating with the EZ-KIT
L When
Lite target board, the LED can flicker, indicating communications
handshake.
User LEDs (LED5–12, LED13–20)
Sixteen LEDs connect to the processor’s programmable flags. Eight LEDs
labeled LED5 through LED12 are controlled by programmable flags PF40
through PF47 (equivalent to PPI0_D15–8). Eight LEDs labeled LED13
through LED20 are controlled by programmable flags PF32 through PF39
(equivalent to PPI1_D15–8). To learn how to use the LEDs, refer to “LEDs
and Push Buttons” on page 1-10.
Table 2-11. User LEDs
LED Reference Designator Flag Port Name
LED Reference Designator Flag Port Name
LED5
PB40
LED13
PB32
LED6
PB41
LED14
PB33
LED7
PB42
LED15
PB34
LED8
PB43
LED16
PB35
LED9
PB44
LED17
PB36
LED10
PB45
LED18
PB37
LED11
PB46
LED19
PB38
LED12
PB47
LED20
PB39
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
2-17
Connectors
Connectors
This section describes the connector functionality and provides information about mating connectors. The connector locations are shown in
Figure 2-4.
Figure 2-4. Connector Locations
Expansion Interface (J1–3)
Three board-to-board connector footprints provide signals for most of the
processor’s peripheral interfaces. The connectors are located at the bottom
of the board. For more information about the interface, see “Expansion
Interface” on page 2-8. For the availability and pricing of the J1, J2, and
J3 connectors, contact Samtec.
2-18
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Hardware Reference
Part Description
Manufacturer
Part Number
90-position 0.05" spacing, SMT
(J1, J2, J3)
SAMTEC
SFC-145-T2-F-D-A
Mating Connector
90-position 0.05” spacing
(through hole)
SAMTEC
TFM-145-x1 series
90-position 0.05” spacing
(surface mount)
SAMTEC
TFM-145-x2 series
90-position 0.05” spacing
(low cost)
SAMTEC
TFC-145 series
Audio (J4 and J5)
Part Description
Manufacturer
Part Number
2x2 RCA jacks (J4)
SWITCHCRAFT
PJRAS2X2S01X
3x2 RCA jacks (J5)
SWITCHCRAFT
PJRAS3X2S01X
Mating Connector
Two channel RCA interconnect cable MONSTER CABLE
BI100-1M
Video (J6)
Part Description
Manufacturer
Part Number
3x2 RCA jacks (J6)
SWITCHCRAFT
PJRAS3X2S01X
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
2-19
Connectors
Power (J7)
The power connector provides all of the power necessary to operate the
EZ-KIT Lite board.
Part Description
Manufacturer
Part Number
2.5 mm power jack (J7)
SWITCHCRAFT
RAPC712X
Mating Power Supply (shipped with EZ-KIT Lite)
7V power supply
CUI INC.
DMS070214-P6P-SZ
The power connector supplies DC power to the EZ-KIT Lite board.
RS-232 (P2)
The RS-232 compatible connector is described in Table 2-12.
Table 2-12. RS-232 Connector
Part Description
Manufacturer
Part Number
DB9, male, right angle (P2)
TYCO
5747250-4
Mating Assembly
2m female-to-female cable
DIGI-KEY
AE1016-ND
SPORT1 (P3)
The SPORT1 connector is linked to a 20-pin connector. The connector’s
pinout can be found in “ADSP-BF561 EZ-KIT Lite Schematic” on
page B-1.
2-20
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Hardware Reference
Part Description
Manufacturer
Part Number
IDC header
FCI
68737-420HLF
Mating Connectors
IDC socket
DIGI-KEY
S4210-ND
SPI (P5)
The SPI connector is linked to a 12-pin connector. The connector’s
pinout can be found in “ADSP-BF561 EZ-KIT Lite Schematic” on
page B-1.
Part Description
Manufacturer
IDC header
SULLINS
Part Number
GEC06DAAN
Mating Assembly
IDC socket
DIGI-KEY
S4207-ND
JTAG (ZP4)
The JTAG header is the connecting point for a JTAG in-circuit emulator
pod. When an emulator connects to the JTAG header, the USB debug
interface is disabled.
3 is missing to provide keying. Pin 3 in the mating connector
L Pin
should have a plug.
using an emulator with the EZ-KIT Lite board, follow the
L When
connection instructions provided with the emulator.
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
2-21
Connectors
2-22
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
A ADSP-BF561 EZ-KIT LITE BILL
OF MATERIALS
The bill of materials corresponds to “ADSP-BF561 EZ-KIT Lite Schematic” on page B-1. Please check the latest schematic on the Analog
Devices Web site:
http://www.analog.com/Processors/Processors/DevelopmentTools/tec
hnicalLibrary/manuals/DevToolsIndex.html#Evaluation%20Kit%20Manuals.
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
1
1
74LVC14A
SOIC14
U47
TI
74LVC14AD
2
2
IDT74FCT3244A
PY SSOP20
U13,U30
IDT
IDT74FCT3244APYG
3
1
12.288MHZ
OSC003
U16
DIGI-KEY
SG-8002CA-PCC-ND
(12.288M)
4
1
LT1765 SOIC8
VR5
LINEAR
TECH
LT1765ES8#PBF
5
1
NDS8434A SO-8
U29
FAIRCHILD
NDS8434A
6
2
MT48LC16M16A
2TG-75 TSOP54
U32-33
MICRON
MT48LC16M16A2P75:D
7
1
27MHZ OSC003
U17
DIGI-KEY
SG-8002CA-PCC-ND
(27.00M)
8
2
IDT2305-1DC
SOIC8
U19-20
IDT
IDT2305-1DCG
9
1
SN74LVC1G32
SOT23-5
U10
TI
SN74LVC1G32DBVRE4
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
A-1
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
10
1
30MHZ OSC003
U14
DIGI-KEY
SG-8002CA-PCC-ND
(30.000M)
11
1
BF561
M29W640D
"U27"
U27
ST MICRO
M29W640DT 90N6E
12
1
ADM708SARZ
SOIC8
U46
ANALOG
DEVICES
ADM708SARZ
13
1
ADP3338AKCZ33 SOT-223
VR3
ANALOG
DEVICES
ADP3338AKCZ-3.3-RL
14
1
ADP3339AKCZ-5
SOT-223
VR1
ANALOG
DEVICES
ADP3339AKCZ-5-R7
15
1
ADP3339AKCZ33 SOT-223
VR6
ANALOG
DEVICES
ADP3339AKCZ-3.3-R7
16
2
ADP3336ARMZ
MSOP8
VR2,VR4
ANALOG
DEVICES
ADP3336ARMZ-REEL
17
1
10MA
AD1580BRTZ
SOT23D
D1
ANALOG
DEVICES
AD1580BRTZ-REEL7
18
4
ADG752BRTZ
SOT23-6
U22-23,U25-26
ANALOG
DEVICES
ADG752BRTZ-REEL
19
3
AD8061ARTZ
SOT23-5
U1-3
ANALOG
DEVICES
AD8061ARTZ-REEL
20
1
ADM3202ARNZ
SOIC16
U21
ANALOG
DEVICES
ADM3202ARNZ
21
8
AD8606ARZ
SOIC8
U5-7,U9,U11-12,
U18,U24
ANALOG
DEVICES
AD8606ARZ
22
1
AD1836AASZ
MQFP52
U15
ANALOG
DEVICES
AD1836AASZ
23
1
ADSP-BF561SKB
CZ MBGA256
U48
ANALOG
DEVICES
ADSP-BF561SKBCZ600
24
1
ADV7179KCPZ
LFCSP40
U8
ANALOG
DEVICES
ADV7179KCPZ
A-2
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Bill Of Materials
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
25
1
ADV7183AKST
LQFP80
U4
ANALOG
DEVICES
ADV7183ABST
26
5
RUBBER FOOT
M1-5
MOUSER
517-SJ-5018BK
27
8
RUBBER FOOT
MH1-8
MOUSER
517-SJ-5018BK
28
1
PWR
2.5MM_JACK
CON005
J7
SWITCHCRAFT
RAPC712X
29
1
RCA 2X2 CON013
J4
SWITCHCRAFT
PJRAS2X2S01X
30
5
MOMENTARY
SWT013
SW1,SW6-9
PANASONIC
EVQ-PAD04M
31
3
.05 45X2 CON019
J1-3
SAMTEC
SFC-145-T2-F-D-A
32
3
DIP6 SWT017
SW2,SW4,SW10
C&K
TDA06H0SB1
33
2
RCA 3X2 CON024
J5-6
SWITCHCRAFT
PJRAS3X2S01X
34
4
DIP4 SWT018
SW3,SW5,
SW11-12
ITT
TDA04HOSB1
35
1
IDC 2X1 IDC2X1
P1
FCI
90726-402HLF
36
1
IDC 7X2 IDC7X2
ZP4
FCI
68737-414HLF
37
1
IDC 10X2
IDC10X2
P3
FCI
68737-420HLF
38
1
2.5A RESETABLE
FUS001
F1
RAYCHEM
SMD250F-2
39
1
DB9 9PIN DB9M
P2
TYCO
5747250-4
40
1
IDC 6X2 IDC6X2
P5
SULLINS
GEC06DAAN
41
12
0 1/4W 5% 1206
R43-44,R55,R71,
R73,R133,R159,
R163,R223-225,
R247
KOA
0.0ECTRk7372BTTED
42
16
YELLOW LED001
LED5-20
PANASONIC
LN1461C
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
A-3
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
43
12
330PF 50V 5%
0805
C82,C84,C86,
C92-100
AVX
08055A331JAT
44
45
0.01UF 100V 10%
0805
C3,C5,C28,C41,
C49,C69-70,
C74-75,C101,
C112-114,C127,
C134,C136-138,
C140-141,C146,
C149-150,C154,
C156-157,
C165-166,C168,
C173-174,C176,
C181-182,
C185-188,C190,
C200-203,C249,
C256
AVX
08051C103KAT2A
45
8
0.22UF 25V 10%
0805
C104,C106-108,
C125,C129,C143,
C162
AVX
08053C224FAT
46
68
0.1UF 50V 10%
0805
C1-2,C4,C12,
C19-20,C22,C27,
C29-30,C35,C37,
C42,C48,C51-60,
C65-66,C71,C73,
C83,C85,C87-91,
C102,C109-111,
C115,C122-124,
C126,C131-132,
C135,C139,C145,
C147-148,
C151-152,C155,
C158-159,C164,
C167,C171-172,
C175,C177-179,
C183-184,C189,
C191
AVX
08055C104KAT
A-4
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Bill Of Materials
Ref.
Qty.
Description
Reference
Designator
Manufacturer
47
10
1000PF 50V 5%
0805
C23,C25,C33,C36, AVX
C38-40,C67-68,
C133
08055A102JAT2A
48
6
10UF 16V 10% C
CT17-18,
CT20-21,CT23-24
AVX
TAJC106K016R
49
44
10K 1/10W 5%
0805
R2,R7,R11-12,
R14,R24,R42,
R45-47,R52,R57,
R78,R85,R87-88,
R98,R131,R143,
R158,R160-162,
R167-170,
R174-177,
R181-183,
R189-190,R196,
R229,R239,R246,
R248-251
VISHAY
CRCW080510K0JNEA
50
9
33 1/10W 5%
0805
R39,R41,R59-61,
R165-166,
R171-172
VISHAY
CRCW080533R0JNEA
51
1
4.7K 1/10W 5%
0805
R86
VISHAY
CRCW08054K70JNEA
52
1
1M 1/10W 5%
0805
R76
VISHAY
CRCW08051M00JNEA
53
1
1.5K 1/10W 5%
0805
R1
VISHAY
CRCW08051K50FKEA
54
1
1.2K 1/8W 5%
1206
R23
VISHAY
CRCW12061K20JNEA
55
6
49.9K 1/8W 1%
1206
R108-113
VISHAY
CRCW120649K9FKEA
56
12
100PF 100V 5%
1206
C6-11,C26,C34,
C61-63,C72
AVX
12061A101JAT2A
57
6
10UF 16V 10% B
CT1-4,CT15-16
AVX
TAJB106K016R
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Part Number
A-5
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
58
4
100 1/10W 5%
0805
R242-245
VISHAY
CRCW0805100RJNEA
59
6
220PF 50V 10%
1206
C13-18
AVX
12061A221JAT2A
60
4
600 100MHZ
200MA 0603
FER18-21
DIGI-KEY
490-1014-2-ND
61
3
2A S2A
DO-214AA
D2-3,D7
VISHAY
S2A-E3
62
15
600 100MHZ
500MA 1206
FER1-4,FER6,
FER8-17
STEWARD
HZ1206B601R-10
63
4
237.0 1/8W 1%
1206
R25-26,R53-54
VISHAY
CRCW1206237RFKEA
64
4
750.0K 1/8W 1%
1206
R132,R156,R164,
R173
VISHAY
CRCW1206750KFKEA
65
16
5.76K 1/8W 1%
1206
R8,R15-16,R40,
R49-50,R58,
R62-64,R69-70,
R121-124
VISHAY
CRCW12065K76FKEA
66
6
11.0K 1/8W 1%
1206
R144-149
VISHAY
CRCW120611K0FKEA
67
8
120PF 50V 5%
1206
C103,C105,C128,
C130,C142,C144,
C161,C163
AVX
12065A121JAT2A
68
12
75 1/8W 5% 1206
R4-6,R100-102,
R104-105,R107,
R114,R134-135
VISHAY
CRCW120675R0JNEA
69
1
68UF 6.3V 20% D
CT22
AVX
TAJD686K016R
70
6
680PF 50V 1%
0805
C116-121
AVX
08055A681FAT2A
71
3
10UF 25V
+80-20% 1210
C31,C47,C50
PANASONIC
ECJ4YF1E106Z
A-6
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Bill Of Materials
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
72
6
2.74K 1/8W 1%
1206
R150-155
VISHAY
CRCW12062K74FKEA
73
12
5.49K 1/8W 1%
1206
R17-22,R27,
R30-31,R34-35,
R38
VISHAY
CRCW12065K49FKEA
74
6
3.32K 1/8W 1%
1206
R137-142
VISHAY
CRCW12063K32FNEA
75
6
1.65K 1/8W 1%
1206
R28-29,R32-33,
R36-37
VISHAY
CRCW12061K65FKEA
76
10
10UF 16V 20%
CAP002
CT5-14
PANASONIC
EEE1CA100SR
77
1
2A SL22
DO-214AA
D6
GENERAL
SEMI
SL22-E3/2C
78
1
53.6K 1/10W 1%
0805
R75
VISHAY
CRCW080553K6FKEA
79
1
10UH 20%
IND001
L11
TDK
445-2014-1-ND
80
18
0 1/10W 5% 0805
R51,R66,R74,R77,
R79,R81-84,R99,
R103,R106,R178,
R184,R191-192,
R252-253
VISHAY
CRCW08050000ZSEA
81
1
190 100MHZ 5A
FER002
FER5
MURATA
DLW5BSN191SQ2
82
2
3.32K 1/10W 1%
0805
R194-195
PANASONIC
ERJ-6ENF3321V
83
5
22 1/10W 5%
0805
R65,R67-68,
R187-188
VISHAY
CRCW080522R0JNEA
84
6
0.68UH 10% 0805
L1-4,L6,L8
MURATA
LQM21NNR68K10D
85
1
.082UF 50V 5%
0805
C64
AVX
08055C823JAT2A
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
A-7
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
86
1
1A ZHCS1000
SOT23D
D5
ZETEX
ZHCS1000TA pb-free
87
3
2.2UH 10% 0805
L5,L7,L9
DIGI-KEY
490-1119-2-ND
88
5
1UF 10V 10%
0805
C21,C24,C32,
C44-45
AVX
0805ZC105KAT2A
89
1
4.7UF 6.3V 10%
0805
C169
AVX
08056D475KAT2A
90
1
1.5UH 20%
IND003
L10
COIL CRAFT
DO1608C-152MLC
91
1
100MA CMDSH-3
SOD-323
D4
CENTRAL
SEMI
CMDSH-3-E3
92
1
0.18UF 25V 10%
0805
C170
AVX
08053C184KAT2A
93
1
100UF 10V 10% C
CT19
KOA
TMC1ACTTE107K
94
1
2.2UF 10V 10%
0805
C43
AVX
0805ZD225KAT2A
95
1
76.8K 1/10W 1%
1206
R48
VISHAY
CRCW120676K8FKEA
96
1
147.0K 1/10W 1%
1206
R56
VISHAY
CRCW1206147KFKEA
97
10
10 62.5MW 5%
RNS006
RN1,RN4-12
PANASONIC
EXB-38V100JV
98
1
17.4K 1/10W 1%
0805
R180
PANASONIC
ERJ-6ENF1742V
99
1
10.0K 1/8W 1%
1206
R186
DALE
CRCW120610K0FKEA
100
1
680 1/8W 5%
1206
R119
VISHAY
CRCW1206680RFNEA
101
1
150.0 1/8W 1%
1206
R3
VISHAY
CRCW1206150RFKEA
A-8
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
ADSP-BF561 EZ-KIT Lite Bill Of Materials
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
102
1
GREEN LED001
LED1
PANASONIC
LN1361CTR
103
1
RED LED001
LED2
PANASONIC
LN1261CTR
104
2
1000PF 50V 5%
1206
C153,C160
AVX
12065A102JAT2A
105
7
2200PF 50V 5%
1206
C46,C76-81
AVX
12065A222JAT050
106
6
1K 1/8W 5% 1206
R10,R115-118,
R136
VISHAY
CRCW12061K00FNEA
107
3
100K 1/8W 5%
1206
R9,R13,R157
VISHAY
CRCW1206100KFNEA
108
17
270 1/8W 5%
1206
R120,R213-220,
R230-237
VISHAY
CRCW1206270RJNEA
109
6
604.0 1/8W 1%
1206
R125-130
PANASONIC
ERJ-8ENF6040V
110
4
1UF 25V 20% A
CT25-28
AVX
TAJA105K020R
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
A-9
A-10
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
A
B
C
D
1
1
2
2
ADSP-BF561 EZ-KIT Lite
Schematic
3
3
ANALOG
DEVICES
4
Board No.
C
Date
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-BF561 EZ-KIT LITE
TITLE
Title
Size
20 Cotton Road
Rev
A0185-2003
2.0
Sheet
4-25-2006_12:39
D
1
of
14
A
B
C
D
U48
D0
D[31:0]
1
B16
D1
C15
D2
E12
D3
C16
D4
E14
D5
D15
D6
D16
D7
E15
D8
F13
D9
F15
D10
F12
D11
F16
D12
F14
3.3V
D13
G15
D14
G13
D15
G12
A[25:2]_S
D0
A2
D1
A3
D2
A4
D3
A5
D4
A6
D5
A7
D6
A8
D7
A9
D8
A10
D9
A11
D10
A12
D11
A13
D12
A14
D13
A15
D14
A16
D15
A17
R42
10K
0805
D16
R60
33
0805
U14
1
OE
OUT
3
H12
D17
H15
D18
H13
D19
H16
D20
H14
D21
J15
OSC_30MHZ
30MHZ
OSC003
R51
DNP
0805
EXT_DSP_CLK
D22
J13
D23
J16
D24
K14
D25
K15
D26
K13
D27
L15
3.3V
2
R160
10K
0805
R196
10K
0805
D28
K12
D29
L16
D30
D31
J12
M15
D16
A18
D17
A19
D18
A20
D19
A21
D20
A22
D21
A23
D22
A24
D23
A25
B12
ARDY
F1
3.3V
G1
D27
D28
D29
D30
SDQM0/ ABE0
SDQM1/ ABE1
SDQM2/ ABE2
SDQM3/ ABE3
BR
BGH
ARDY
ARE
RESET
CLKIN
AMS1
XTAL
AMS2
SRAS
SCAS
R170
10K
0805
SWE
SA10
SMS0
3
DSP_BYPASS
BMODE0
G4
M10
BMODE1
N10
BYPASS
SMS1
SMS2
BMODE0
SMS3
BMODE1
SCKE
P11
NMI0
NMI1
R9
A5_S
B14
A6_S
C14
A7_S
A2_S
1
F11
A8_S
A3_S
2
RN4
D7
A9_S
A4_S
3
A6
A10_S
A5_S
4
C6
A11_S
A12_S
E6
A13_S
A5
A14_S
A6_S
1
E5
A15_S
A7_S
2
B4
A16_S
A8_S
3
A17_S
B3
A18_S
A9_S
4
A3
A20_S
F5
A21_S
A10_S
1
B2
A22_S
A11_S
2
D4
A23_S
A12_S
3
C3
A25_S
R2B
R3A
R3B
R4A
R4B
1
BMODE0
2
BMODE1
ON
ON
RESERVED
OFF
ON
8-BIT FLASH
ON
OFF
SPI SROM 8-BIT
OFF
A13_S
NMI0
SCLK0
NMI1
SCLK1
A4
5
A5
A15_S
A16_S
R1A
R1B
R2A
R2B
R3A
R3B
R4A
R4B
8
A6
7
A7
4
1
R1A
2
R2A
3
R3A
4
R4A
R1B
R2B
R3B
R4B
8
A14
7
A15
6
A16
5
A17
8
A18
7
A19
6
A20
5
A21
8
A22
7
A23
6
A24
5
A25
E11
ABE0_S
1
B13
ABE1_S
2
A14
ABE2_S
3
A15
ABE3_S
4
A13
6
A8
A18_S
A19_S
5
A9
A20_S
A21_S
1
R1A
2
R2A
3
R3A
4
R4A
R1B
R2B
R3B
R4B
10
RNS006
R1A
R1B
R2A
R2B
R3A
R3B
R4A
R4B
8
A10
7
A11
6
A12
RN8
A22_S
A23_S
5
A13
A24_S
A25_S
1
R1A
2
R2A
3
R3A
4
R4A
R1B
R2B
R3B
R4B
A[25:2]
R1A
R1B
R2A
R2B
R3A
R3B
R4A
R4B
8
C12
7
ABE1
6
ABE2
5
ABE3
BGH
C7
AOE
B8
ARE
A8
AWE
C8
AMS0
B7
AMS1
E7
AMS2
A7
AMS3
RN10
C10
SRAS_S
1
D10
SCAS_S
2
E10
SWE_S
3
D11
SA10_S
4
E9
SMS0_S
B9
SMS1_S
C9
SMS2_S
A10
SMS3_S
1
2
B10
A11
SCKE
3
SCLK0_S
4
A12
R1A
R1B
R2A
R2B
R3A
R3B
R4A
R4B
8
SRAS
7
SCAS
6
SWE
5
SA10
10
RNS006
RN9
SCLK1_S
3
R1A
R1B
R2A
R2B
R3A
R3B
R4A
R4B
8
SMS0
7
SMS1
6
SMS2
5
SMS3
R187
22
0805
SCLK0
3.3V
U20
REF
CLKOUT
CLK1
DEFAULT
6
SPI SROM 16-BIT
4
VDD
CLK3
GND
CLK4
R68
22
0805
8
3
CLK_OUT_EXP1
2
R67
22
0805
5
CLK_OUT_EXP2
7
R65
22
0805
IDT2305-1DC
SOIC8
SW3
ON
1
3
6
4
5
2
3
ANALOG
DEVICES
8
7
DNP
4
Title
DIP4
SWT018
Size
Date
B
C
20 Cotton Road
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-BF561 EZ-KIT LITE
DSP - EXT MEM INTERFACE
Board No.
C
A
2
ABE0
10
RNS006
BG
1
2
1
RN6
R176
10K
0805
BOOT MODE
4
6
10
RNS006
R188
22
0805
1
RN12
A14_S
10
RNS006
CLK2
OFF
A3
RN7
ADSP-BF561
MBGA256
SW3: BOOT MODE/BYPASS Select
(Default = OFF, ON, ON, OFF)
7
A17_S
10
RNS006
R169
10K
0805
A2
10
RNS006
A19_S
A24_S
R2A
8
RN5
C4
A2
R1B
10
RNS006
B5
F6
R1A
D31
AMS3
R168
10K
0805
G10
RN11
C42
0.1UF
0805
DNP
R167
10K
0805
A4_S
D26
AMS0
DSPCK_30MHZ
A3_S
B15
10
RNS006
AWE
F3
RESET
G11
D25
AOE
D9
A2_S
D24
BG
BR
D13
Rev
A0185-2003
2.0
Sheet
4-25-2006_13:36
D
2
of
14
A
B
C
D
U48
P15
RSCLK0
R16
RFS0
L12
DR0PRI
P16
DR0SEC
N16
TSCLK0
L13
TFS0
1
RSCLK0/PF28
M16
DT0PRI
RFS0/PF19
PF14
DR0PRI
PF13
DR0SEC/PF20
PF12
TSCLK0/PF29
PF11
TFS0/PF16
PF10
DT0PRI/PF18
N15
DT0SEC
PF15/TMRXCLK
PF9
DT0SEC/PF17
PF8
PF7/SPIS7/TMR7
P13
RSCLK1
N13
RFS1
M12
DR1PRI
T14
DR1SEC
R14
TSCLK1
T15
DT1SEC
PF5/SPIS5/TMR5
DR1PRI
PF4/SPIS4/TMR4
DR1SEC/PF25
PF3/SPIS3/TMR3
TSCLK1/PF31
PF2/SPIS2/TMR2
TFS1/PF21
PF1/SPIS1/TMR1
DTIPRI/PF23
PF0/SPISS/TMR0
PF14
N8
PF13
T7
PF12
P7
PF11
PF[15:0]
RN1
R7
N6
PF15
1
PF14
2
PF13
3
PF10
PF9
R1A
R2A
R1B
R2B
R3A
R3B
PF7
R4A
R4B
T5
PF6
10
RNS006
P6
8
AD1836_RESET
7
PROGR. FLAG
VENC_RESET
6
1
VDEC_RESET
AD1836 CODEC RESET
PF14
ADV7179 VIDEO ENCODER RESET
PF13
ADV7183A VIDEO DECODER RESET
PF5
PF12
GENERAL PURPOSE
R5
PF4
PF11
GENERAL PURPOSE
M6
PF3
PF10
GENERAL PURPOSE
T4
PF2
PF8
M7
4
N5
SPIS1
SW13
1
P4
SPISS
2
5
PF9
GENERAL PURPOSE
4
PF1
PF8
GENERAL PURPOSE / PUSH BUTTON STATUS INPUT
3
PF0
PF7
GENERAL PURPOSE / PUSH BUTTON STATUS INPUT
PF6
GENERAL PURPOSE / PUSH BUTTON STATUS INPUT/ UART SIGNAL
PF5
GENERAL PURPOSE / PUSH BUTTON STATUS INPUT/ UART SIGNAL
PF4
GENERAL PURPOSE / AD1836 LATCH SIGNAL
PF3
GENERAL PURPOSE / VIDEO DECODER FIELD
PF2
GENERAL PURPOSE / VIDEO DECODER OUTPUT ENABLE
PF1
GENERAL PURPOSE / I2C SERIAL DATA/SPISEL1
PF0
GENERAL PURPOSE / I2C SERIAL CLOCK/SPISS
DIP2
SWT020
DT1SEC/PF22
3.3V
T13
RX
TX
3.3V
SCK
R10
TDI
3V
2
ZP4
1
DA_EMULATOR_SELECT
3
4
EMULATOR_EMU
5
6
EMULATOR_TMS
7
8
EMULATOR_TCK
9
10
EMULATOR_TRST
11
12
EMULATOR_TDI
13
14
T10
TMS
2
EMULATOR_TDO
DA_EMULATOR_EMU
2
TRST
EMU
R11
EMU
TDI
DA_EMULATOR_TCK
TDO
P5
TDO
DA_EMULATOR_TRST
MOSI
EMU
DA_EMULATOR_TDI
DA_EMULATOR_TDO
GP0
GP1
EMU
R86
4.7K
0805
SPISS
SCK
ADSP-BF561
MBGA256
RESET
GP2
SPIS1
GP3
MISO
SHGND
DA_SOFT_RESET
GND
DA_SOFT_RESET
TDO
DA_EMULATOR_TMS
IDC7X2
RESET
N9
TCK
P10
TRST
TDO
TMS
T9
TCK
SW13: SPIS1/SPISS Select
MISO
M11
SCK
T11
MOSI
R12
MISO
SLEEP
TX/PF26
N11
MOSI
R239
10K
0805
RX/PF27
R13
FUNCTION
PF15
R6
2
R15
DT1PRI
RFS1/PF24
R8
ON
TFS1
PF6/SPIS6/TMR6
PF15
1
P14
RSCLK1/PF30
P8
1
2
3
4
5
6
7
8
9
10
11
12
IDC6X2
DEBUG_AGENT
DSP JTAG HEADER
SPI
SHGND
DSP_VDD_EXT
DSP_VDD_INT
U48
A1
A16
A4
A9
B11
B6
D12
E16
F2
G16
G3
J6
K16
K6
L10
L5
M14
T1
T12
T16
T3
T6
T8
3
C11
C13
C5
D14
D5
D6
D8
E1
E13
F10
F8
G14
G2
G6
G7
G8
H1
H10
H2
H8
H9
4
VDDEXT1
VDDEXT2
VDDEXT3
VDDEXT4
VDDEXT5
VDDEXT6
VDDEXT7
VDDEXT8
VDDEXT9
VDDEXT10
VDDEXT11
VDDEXT12
VDDEXT13
VDDEXT14
VDDEXT15
VDDEXT16
VDDEXT17
VDDEXT18
VDDEXT19
VDDEXT20
VDDEXT21
VDDEXT22
VDDEXT23
VDDINT1
VDDINT2
VDDINT3
VDDINT4
VDDINT5
VDDINT6
VDDINT7
VDDINT8
VDDINT9
VDDINT10
VDDINT11
VDDINT12
VDDINT13
VDDINT14
R87
10K
0805
VROUT2
GND41
GND40
GND39
GND38
GND37
GND36
GND35
GND34
GND33
GND32
GND31
GND30
GND29
GND28
GND27
GND26
GND25
GND24
GND23
GND22
J1
R85
10K
0805
3
SPORT1
RFS1
RSCLK1
DR1PRI
DR1SEC
VROUT1
NC0
NC1
GND1
GND2
GND3
GND4
GND5
GND6
GND7
GND8
GND9
GND10
GND11
GND12
GND13
GND14
GND15
GND16
GND17
GND18
GND19
GND20
GND21
R88
10K
0805
E8
F7
F9
G9
H11
H6
H7
J10
J8
J9
K11
K8
L8
M8
VROUT
J2
M5
M13
P9
P5
P2
P12
N7
N14
N12
M9
M4
L9
L7
L3
L14
L11
K9
K7
K10
J7
J14
J11
P3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
ANALOG
DEVICES
Title
Size
DT1PRI
DT1SEC
Date
C
20 Cotton Road
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-BF561 EZ-KIT LITE
DSP - PROGR. FLAGS, SPI
Board No.
C
B
TSCLK1
IDC10X2
ADSP-BF561
MBGA256
A
TFS1
Rev
A0185-2003
2.0
Sheet
4-25-2006_16:26
D
3
of
14
A
B
C
D
SW5: PPI CLK Routing Select
(Default: 1 = OFF, 2 = ON, 3 = ON, 4 = ON)
1 or 3
PPIxCLK_SEL0
2 or 4
PPIxCLK_SEL1
PPIxCLK
ON
ON
PPI_27MHZ_CLK
OFF
ON
VDEC_CLKOUT
X
OFF
EXPANSION_CLK
3.3V
3.3V
R166
33
0805
VDEC_27MHZ_CLK
R165
33
0805
1
R162
10K
0805
U22
3
R174
10K
0805
VENC_27MHZ_CLK
3.3V
R175
10K
0805
R182
10K
0805
R181
10K
0805
R171
33
0805
R59
33
0805
U17
1
OE
OUT
3
U23
1
1
R66
0
0805
3
6
1
PPI0_CLK
6
4
EXT_27MHZ_CLK
U19
4
OSC_27M
OSC27M
1
REF
CLKOUT
8
ADG752BRTZ
SOT23-6
3
CLK1
2
CLK2
5
CLK3
7
CLK4
27MHZ
OSC003
6
VDD
4
GND
ADG752BRTZ
SOT23-6
EXP_PPI0_CLK
R172
33
0805
U26
PPI_27MHZ_CLK
3
U25
1
IDT2305-1DC
SOIC8
2
2
ON
1
1
6
VDEC_CLKOUT
SW5
R178
0
0805
3
1
8
PPI1_CLK
6
PPI0CLK_SEL0
4
7
PPI0CLK_SEL1
6
4
5
3
3
4
ADG752BRTZ
SOT23-6
PPI1CLK_SEL0
4
ADG752BRTZ
SOT23-6
PPI1CLK_SEL1
DIP4
SWT018
EXP_PPI1_CLK
U48
2
PPI0_D[15:0]
PPI0_D15
D2
PPI0_D14
G5
PPI0_D13
D1
PPI0_D12
E3
PPI0_D11
E2
PPI0_D10
F4
PPI0_D9
H3
PPI0_D8
K3
PPI0_D7
H4
PPI0_D6
K1
PPI0_D5
PPI0_D4
K2
PPI0_D3
J4
PPI0_D2
J3
PPI0_D1
J5
PPI0_D0
L1
C2
PPI0_CLK
E4
PPI0_SYNC1
C1
PPI0_SYNC2
3
H5
D3
PPI0_SYNC3
PPI0_D15/PF47
PPI1_D15/PF39
PPI0_D14/PF46
PPI1_D14/PF38
PPI0_D13/PF45
PPI1_D13/PF37
PPI0_D12/PF44
PPI1_D12/PF36
PPI0_D11/PF43
PPI1_D11/PF35
PPI0_D10/PF42
PPI1_D10/PF34
PPI0_D9/PF41
PPI1_D9/PF33
PPI0_D8/PF40
PPI1_D8/PF32
PPI0_D7
PPI1_D7
PPI0_D6
PPI1_D6
PPI0_D5
PPI1_D5
PPI0_D4
PPI1_D4
PPI0_D3
PPI1_D3
PPI0_D2
PPI1_D2
PPI0_D1
PPI1_D1
PPI0_D0
PPI1_D0
PPI0_CLK
PPI1_CLK
PPI0_SYN1/TMR8
PPI1_SYN1/TMR10
PPI0_SYN2/TMR9
PPI1_SYN2/TMR11
PPI0_SYN3
PPI1_SYN3
M1
PPI1_D15
K5
PPI1_D14
M2
PPI1_D13
N1
PPI1_D12
L6
PPI1_D11
PPI1_D8
N2
PPI1_D10
PPI1_D9
M3
PPI1_D9
PPI1_D10
P1
PPI1_D8
PPI1_D11
R1
PPI1_D7
R2
PPI1_D6
P3
U13
2
1A1
4
1A2
6
1A3
8
1A4
PPI1_D12
11
PPI1_D13
13
PPI1_D14
15
PPI1_D15
17
2A1
2A2
PPI1_D5
T2
2
PPI1_D[15:0]
2A3
PPI1_D4
N3
PPI1_D3
2A4
R3
PPI1_D2
N4
PPI1_D1
1
OE1
19
OE2
R4
PPI1_D0
18
1Y1
16
1Y2
14
1Y3
12
1Y4
9
2Y1
7
2Y2
5
2Y3
3
2Y4
LED20
YELLOW
LED001
LED19
YELLOW
LED001
LED18
YELLOW
LED001
LED17
YELLOW
LED001
LED16
YELLOW
LED001
LED15
YELLOW
LED001
LED14
YELLOW
LED001
LED13
YELLOW
LED001
IDT74FCT3244APY
SSOP20
B1
PPI1_CLK
K4
R237
270
1206
PPI1_SYNC1
L2
R236
270
1206
R235
270
1206
R234
270
1206
R233
270
1206
R232
270
1206
R231
270
1206
R230
270
1206
PPI1_SYNC2
L4
3
PPI1_SYNC3
ADSP-BF561
MBGA256
U30
PPI0_D8
2
PPI0_D9
4
PPI0_D10
6
PPI0_D11
8
PPI0_D12
11
PPI0_D13
13
PPI0_D14
15
PPI0_D15
17
1
19
1A1
1Y1
1A2
1Y2
1A3
1Y3
1A4
1Y4
2A1
2Y1
2A2
2Y2
2A3
2Y3
2A4
2Y4
18
16
14
12
9
7
5
3
OE1
OE2
LED12
YELLOW
LED001
LED11
YELLOW
LED001
LED10
YELLOW
LED001
LED9
YELLOW
LED001
LED8
YELLOW
LED001
LED7
YELLOW
LED001
LED6
YELLOW
LED001
LED5
YELLOW
LED001
ANALOG
DEVICES
IDT74FCT3244APY
SSOP20
4
R220
270
1206
R219
270
1206
R218
270
1206
R217
270
1206
R216
270
1206
R215
270
1206
R214
270
1206
R213
270
1206
Board No.
C
Date
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-BF561 EZ-KIT LITE
DSP - PPI0 AND PPI1
Title
Size
20 Cotton Road
Rev
A0185-2003
2.0
Sheet
4-25-2006_13:36
D
4
of
14
A
B
C
FLASH A (8MB)
D
SDRAM 64MB
(256Mb x 2 Chips)
4M x 16
D[31:0]
1
1
U32
A[25:2]
U27
25
ABE3
A2
24
A3
23
A4
22
A5
21
A6
20
A7
19
A8
A9
8
A10
7
A11
6
A12
5
A13
3.3V
2
R190
10K
0805
R177
10K
0805
4
A14
3
A15
2
A16
1
A17
48
A18
17
A19
16
A20
R189
10K
0805
18
9
A21
10
A22
13
26
AMS0
28
AOE
11
AWE
47
FLASH_WP
14
FLASH_RP
12
3.3V
A0
A1
A2
VCC
37
A3
A4
D0
A5
D1
A6
D2
A7
D3
A8
D4
A9
D5
A10
D6
A11
D7
A12
D8
A13
D9
A14
D10
A15
D11
A16
D12
A17
D13
A18
D14
A19
D15
29
D0
31
D1
33
D2
35
D3
38
D4
40
D5
42
D6
44
D7
30
D8
32
D9
34
D10
36
D11
23
A3
24
A4
25
A5
26
A6
29
A7
30
A8
31
A9
32
A10
33
A11
34
SCAS
41
D13
SRAS
43
D14
45
D15
R183
10K
0805
A20
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A13
35
A14
36
A11
A12_NC
A18
20
A19
21
BA0
BA1
16
SWE
3.3V
2
DQ0
4
DQ1
5
DQ2
7
DQ3
8
DQ4
10
DQ5
11
DQ6
13
DQ7
42
DQ8
44
DQ9
45
DQ10
47
DQ11
48
DQ12
50
DQ13
51
DQ14
53
DQ15
A0
22
SA10
D12
39
A2
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
19
CS
37
CKE
38
CLK
WE
17
CAS
18
RAS
SMS0
2
SCKE
SCLK0
15
ABE0
DQML
39
ABE1
DQMH
A21
CE
RDY
15
MT48LC16M16A2TG-75
TSOP54
FLASH_RDY
OE
U33
WE
BYTE
VSS2
WP/VPP
VSS1
46
A2
23
RP
A3
24
M29W640D
TSOP48
A4
25
A5
26
A6
29
A7
30
A8
31
2
DQ0
4
DQ1
5
DQ2
7
DQ3
8
DQ4
10
DQ5
11
DQ6
13
DQ7
42
DQ8
44
DQ9
45
DQ10
47
DQ11
48
DQ12
50
DQ13
51
DQ14
53
DQ15
A0
27
A1
A2
A3
A4
A5
A6
A9
32
A10
33
A11
34
A7
A8
A9
22
A10
3
A13
35
A14
36
A11
A12_NC
A18
20
A19
21
BA0
BA1
D16
D17
D18
D19
D20
D21
D22
D23
D24
D25
D26
3
D27
D28
D29
D30
D31
Memory Map
16
START
0x0000 0000
0x2000 0000
END
0x03FF FFFF
0x207F FFFF
BANK
SDRAM Bank 0
ASYNC Memory Bank 0
19
CS
37
CKE
38
CLK
WE
DEVICE
17
CAS
18
64MB SDRAM
8MB FLASH
RAS
ABE2
ABE3
15
DQML
39
DQMH
MT48LC16M16A2TG-75
TSOP54
ANALOG
DEVICES
4
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-BF561 EZ-KIT LITE
MEMORY - FLASH & SDRAM
Board No.
C
Date
20 Cotton Road
Rev
A0185-2003
2.0
Sheet
4-25-2006_12:42
D
5
of
14
A
B
C
D
ADC2
ADC1
R61
33
0805
U16
1
LEFT (WHITE)
3
OUT
OE
1
DAC1
R161
10K
0805
DAC2
DAC3
3.3V
AD1836_CLK
RIGHT (RED)
1
12.288MHZ
OSC003
OUT (J4)
R18
5.49K
1206
IN (J5)
R145
11.0K
1206
C7
100PF
1206
R138
3.32K
1206
OUT1R-
C96
330PF
0805
3.3V
U5
6
7
DAC1 RIGHT
5
C117
680PF
0805
R30
5.49K
1206
R57
10K
0805
AD8606ARZ
SOIC8
R29
1.65K
1206
R126
604.0
1206
OUT1R+
AUDIO CODEC
J5
CT8
10UF
CAP002
CON024
DAC1_RIGHT 7
U15
1
DR0PRI
ON
SW12
1
7
48
3
6
44
4
5
43
3
RFS0
4
RSCLK0
47
2
2
DR0SEC
8
ASDATA1
OUT1L+
ASDATA2
OUT1L-
ABCLK
OUT1R+
OUT1R-
45
AD1836_CLK
PF4
9
OUT1L-
R151
2.74K
1206
DAC1 LEFT
C14
220PF
1206
9
31
OUT1R+
30
OUT1R-
DAC1 RIGHT
2
CLATCH
OUT2L-
6
OUT2L+
7
OUT2L-
DAC2 LEFT
AGND
51
SCK
CCLK
2
CDATA
49
COUT
MOSI
MISO
ADC1 LEFT
R46
10K
0805
R45
10K
0805
16
IN1L+
R47
10K
0805
17
IN1L-
ADC1 RIGHT
18
IN1R+
19
IN1R-
R109
49.9K
1206
C77
2200PF
1206
MCLK
OUT2L+
50
OUT1L+
ALRCLK
DIP4
SWT018
2
8
OUT2R+
OUT2R-
IN1L+
OUT3L+
IN1L-
OUT3L-
IN1R+
OUT3R+
IN1R-
OUT3R-
33
OUT2R+
32
OUT2R-
4
OUT3L+
5
OUT3L-
35
OUT3R+
34
OUT3R-
DAC2 RIGHT
DAC3 LEFT
R17
5.49K
1206
R144
11.0K
1206
DAC3 RIGHT
C6
100PF
1206
R137
3.32K
1206
OUT1L20
21
22
IN2L1
ADC2 LEFT
23
IN2L2
24
IN2R2
ADC2 RIGHT IN2R1
25
3
26
27
38
DSDATA1
41
DSDATA2
42
DSDATA3
36
DLRCLK
37
DBCLK
IN2L+/CL2/CL2
IN2L-/CL1/CL1
NC/IN2L1/IN2L+
NC/IN2L2/IN2L-
DT0PRI
FILTR
IN2R-/CR1/CR1
FILTD
TSCLK0
DAC1 LEFT
R159
0
1206
3
C116
680PF
0805
R27
5.49K
1206
13
12
AD8606ARZ
SOIC8
R28
1.65K
1206
C40
1000PF
0805
C38
1000PF
0805
C39
1000PF
0805
J5
CT7
10UF
CAP002
3
CON024
IN2R+/CR2/CR2
DAC1_LEFT 8
CT16
10UF
B
C124
0.1UF
0805
CT15
10UF
B
C123
0.1UF
0805
R150
2.74K
1206
C13
220PF
1206
9
3
C133
1000PF
0805
R108
49.9K
1206
C76
2200PF
1206
AD1836AASZ
MQFP52
R158
10K
0805
R125
604.0
1206
OUT1L+
3
PD/RST
AD1836_RESET
U5
2
1
TFS0
NC/IN2R2/IN2RNC/IN2R1/IN2R+
C95
330PF
0805
DT0SEC
AD8606ARZ
U12
1
AD1836_VREF
AGND
2
SOIC8
R43
0
1206
R55
0
1206
AGND
5
AD8606ARZ
U12
AGND
7
SW10: Audio Loopback
For Test Purposes
Default = All Off
6
SOIC8
SW10
ON
11
3
10
4
9
5
8
6
7
3
ADC2_LEFT
4
ADC2_RIGHT
12
2
2
ADC1_RIGHT
1
ADC1_LEFT
4
1
R44
0
1206
R71
0
1206
ANALOG
DEVICES
DAC1_LEFT
DAC1_RIGHT
Nashua, NH 03063
4
PH: 1-800-ANALOGD
DAC2_LEFT
5
6
ADSP-BF561 EZ-KIT LITE
AUDIO CODEC
Title
DAC2_RIGHT
DAC3_LEFT
AGND
DAC3_RIGHT
Size
DIP6
SWT017
Board No.
C
Date
A
20 Cotton Road
B
C
Rev
A0185-2003
2.0
Sheet
4-25-2006_13:36
D
6
of
14
A
B
C
D
1
1
R19
5.49K
1206
R146
11.0K
1206
C8
100PF
1206
R22
5.49K
1206
R139
3.32K
1206
OUT2R-
R149
11.0K
1206
C97
330PF
0805
2
C100
330PF
0805
3
R31
5.49K
1206
C118
680PF
0805
AD8606ARZ
SOIC8
R32
1.65K
1206
R142
3.32K
1206
OUT3R-
U6
1
DAC2 RIGHT
C11
100PF
1206
6
U7
7
DAC3 RIGHT
R128
604.0
1206
5
J5
CT10
10UF
CAP002
OUT2R+
CON024
DAC2_RIGHT
R38
5.49K
1206
4
C121
680PF
0805
AD8606ARZ
SOIC8
R37
1.65K
1206
R130
604.0
1206
OUT3R+
R152
2.74K
1206
C15
220PF
1206
J5
CT12
10UF
CAP002
CON024
6
AD1836_VREF
DAC3_RIGHT 1
R111
49.9K
1206
C79
2200PF
1206
R155
2.74K
1206
C18
220PF
1206
3
R113
49.9K
1206
C81
2200PF
1206
2
2
AGND
AGND
R20
5.49K
1206
R147
11.0K
1206
C9
100PF
1206
R21
5.49K
1206
R140
3.32K
1206
R148
11.0K
1206
OUT2L-
R141
3.32K
1206
OUT3L-
C98
330PF
0805
6
U6
C99
330PF
0805
7
3
C10
100PF
1206
DAC2 LEFT
2
U7
5
R34
5.49K
1206
C119
680PF
0805
AD8606ARZ
SOIC8
R33
1.65K
1206
R127
604.0
1206
OUT2L+
3
J5
CT9
10UF
CAP002
C16
220PF
1206
R35
5.49K
1206
CON024
DAC2_LEFT 5
R153
2.74K
1206
3
1
DAC3 LEFT
C120
680PF
0805
AD8606ARZ
SOIC8
R36
1.65K
1206
R129
604.0
1206
OUT3L+
J5
CT11
10UF
CAP002
CON024
DAC3_LEFT 2
6
R110
49.9K
1206
C78
2200PF
1206
R154
2.74K
1206
C17
220PF
1206
3
R112
49.9K
1206
C80
2200PF
1206
AGND
AGND
ANALOG
DEVICES
4
Board No.
C
Date
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-BF561 EZ-KIT LITE
AUDIO OUT
Title
Size
20 Cotton Road
Rev
A0185-2003
2.0
Sheet
4-25-2006_12:42
D
7
of
14
A
1
B
J4
CT5
10UF
CAP002
FER10
600
1206
CON013
2
R121
5.76K
1206
C
R49
5.76K
1206
1
J4
CON013
5
C128
120PF
1206
C62
100PF
1206
2
R123
5.76K
1206
R62
5.76K
1206
ADC2_LEFT
6
C142
120PF
1206
C72
100PF
1206
R53
237.0
1206
U11
AGND
2
1
IN1L-
AGND
1
AGND
C25
1000PF
0805
R50
5.76K
1206
AD8606ARZ
SOIC8
C26
100PF
1206
R58
5.76K
1206
R63
5.76K
1206
ADC1 LEFT
C130
120PF
1206
C23
1000PF
0805
R164
750.0K
1206
R54
237.0
1206
U11
6
7
U18
7
IN1L+
5
2
ADC2 LEFT
C144
120PF
1206
AGND
6
IN2L2
3
AD8606ARZ
SOIC8
R156
750.0K
1206
U18
AGND
3
R40
5.76K
1206
CT13
10UF
CAP002
FER12
600
1206
ADC1_LEFT
3
D
IN2L1
5
AD8606ARZ
SOIC8
2
AD8606ARZ
SOIC8
AGND
AGND
J4
CT6
10UF
CAP002
FER11
600
1206
CON013
1
J4
R122
5.76K
1206
R15
5.76K
1206
ADC1_RIGHT
4
3
C103
120PF
1206
C63
100PF
1206
2
CT14
10UF
CAP002
FER9
600
1206
CON013
R25
237.0
1206
U9
R69
5.76K
1206
ADC2_RIGHT
6
AGND
R124
5.76K
1206
C161
120PF
1206
C61
100PF
1206
2
1
1
IN1R-
AGND
AGND
3
R8
5.76K
1206
AD8606ARZ
SOIC8
C36
1000PF
0805
R16
5.76K
1206
C34
100PF
1206
R64
5.76K
1206
AGND
ADC1 RIGHT
6
R173
750.0K
1206
R26
237.0
1206
U9
6
7
ADC2 RIGHT
C163
120PF
1206
C33
1000PF
0805
3
R70
5.76K
1206
C105
120PF
1206
R132
750.0K
1206
IN2R2
3
AD8606ARZ
SOIC8
3
U24
AGND
U24
7
IN1R+
5
IN2R1
5
AD8606ARZ
SOIC8
AD8606ARZ
SOIC8
AGND
AGND
AD1836_VREF
ANALOG
DEVICES
4
Board No.
C
Date
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-BF561 EZ-KIT LITE
AUDIO IN
Title
Size
20 Cotton Road
Rev
A0185-2003
2.0
Sheet
4-25-2006_12:42
D
8
of
14
A
B
1
7
3
6
4
5
3
VIDEO_AVIN5
8
2
2
VIDEO_AVIN4
ON
SW11
1
VIDEO_AVIN1
C
D
VIDEO_DAC_A
VIDEO_DAC_C
VIDEO_DAC_B
4
DIP4
SWT018
1
SW11: Video Loopback
For Test Purposes
Default = All Off
R136
1K
1206
DAC A
DAC B
DAC C
Composite Video
CVSB
CVSB
C
Component Video
G
B
R
Differential Component Video
Y
U
V
S Video
Y
1
C
A3V
VIDEO_DAC_A
U3
L1
0.68UH
0805
L5
2.2UH
0805
J6
R104
75
1206
5
4
L4
0.68UH
0805
1
3
C92
330PF
0805
C86
330PF
0805
R6
75
1206
8
DAC A
AD8061ARTZ
SOT23-5
2
R114
75
1206
CON024
9
R10
1K
1206
AGND2
VIDEO ENCODER
3V_B
R116
1K
1206
2
2
U8
VAA1
VAA2
VAA3
VAA4
VAA5
PPI1_D[15:0]
JP1
PPI1_D7
5
PPI1_D6
4
PPI1_D5
3
PPI1_D4
39
PPI1_D3
38
PPI1_D2
37
PPI1_D1
36
PPI1_D0
35
1
VENC_27MHZ_CLK
2
P7
DAC_A
P6
DAC_B
P5
DAC_C
P3
COMP
P2
VREF
P1
RSET
IDC3X1
CLOCK
FIELD/VSYNC
BLANK
20
VENC_RESET
3
16
PF[15:0]
PF1
22
PF0
21
GND1
GND2
SDATA
GND3
SCLOCK
GND5
GND6
34
33
R14
10K
0805
25
C115
0.1UF
0805
C12
0.1UF
0805
R23
1.2K
1206
U1
GND7
SCRESET/RTC
GND8
TTX
GND9
TTXREQ
GND10
L8
0.68UH
0805
29
L9
2.2UH
0805
R107
75
1206
5
4
L2
0.68UH
0805
28
3
DAC B
5
AD8061ARTZ
SOT23-5
2
24
23
R135
75
1206
30
6
C94
330PF
0805
C82
330PF
0805
R4
75
1206
R115
1K
1206
31
13
VENC_HS
14
VENC_VS
15
R118
1K
1206
6
3
7
8
A3V
1
9
R3
150.0
1206
11
12
D1
AD1580BRTZ
SOT23D
VIDEO_DAC_C
2
U2
J6
17
4
19
L6
0.68UH
0805
26
L7
2.2UH
0805
2
R134
75
1206
C93
330PF
0805
C84
330PF
0805
R5
75
1206
2
DAC C
AD8061ARTZ
SOT23-5
3
R117
1K
1206
AGND2
ANALOG
DEVICES
4
Title
AGND2
Size
Date
C
20 Cotton Road
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-BF561 EZ-KIT LITE
VIDEO ENCODER (VIDEO OUT)
Board No.
C
B
CON024
1
40
R9
100K
1206
R105
75
1206
5
L3
0.68UH
0805
3
R133
0
1206
A
CON024
1
ADV7179KCPZ
LFCSP40
R143
10K
0805
J6
27
AGND2
ALSB
3V_B
32
VIDEO_DAC_B
18
RESET
GND4
R13
100K
1206
10
P0
HSYNC
1
A3V
P4
3
VDEC_CLKOUT
2
Rev
A0185-2003
2.0
Sheet
4-25-2006_13:36
D
9
of
14
C
DAC_D
B
DAC_B
DAC_C
A
3.3V
(WHITE) OUT
1
D
VIDEO DECODER
R12
10K
0805
(RED) IN
R11
10K
0805
R131
10K
0805
R2
10K
0805
Note: Signal Names in brackets refer to ADV7183KST
1
XTAL1
P15
P14
P13
Composite Video
CVBS
CVBS
CVBS
Differential Component Video
Y
S Video
Y
PF[15:0]
V
PF1
67
PF0
68
ALSB
P12
SDA
P11
SCLK
P10
U
P9
C
64
VDEC_RESET
36
R99
0
0805
CON024
7
AVIN1
C60
0.1UF
0805
P8
PWRDN
P7
P6
R7
10K
0805
J6
RESET
65
NC[ISO]
P4
VIDEO_AVIN1
42
41
AIN1
P3
AIN7
P2
9
P1
TP1
44
J6
43
R103
0
0805
CON024
2
4
AVIN4
P5
C66
0.1UF
0805
P0
46
45
AIN3
LLC2
AIN9
NC[LLCREF]
6
ELPF
58
J6
57
R106
0
0805
CON024
1
AVIN5
C65
0.1UF
0805
60
59
AIN10
AIN5
AIN11
3
R100
75
1206
R102
75
1206
HS
62
61
CT3
10UF
B
C58
0.1UF
0805
CT1
10UF
B
FIELD
NC[VREF]
NC[HREF]
TP3
R101
75
1206
C2
0.1UF
0805
AGND2
52
49
AGND2
CT4
10UF
B
C59
0.1UF
0805
C68
1000PF
0805
AIN12
REFOUT
CML
CAPY1
CAPY2
54
NC[CLKIN]
SFL[HFF]
NC[AEF]
NC[RD]
OE
CAPC1
NC[GPO3]
CAPC2
NC[GPO2]
3
NC[GPO1]
NC[GPO0]
C4
0.1UF
0805
CT2
10UF
B
C57
0.1UF
0805
C67
1000PF
0805
50
AVDD
DVDD1
DVDD2
DVDD3
AGND2
A3V
A5V
AGND2
38
C54
0.1UF
0805
C1
0.1UF
0805
PVDD
DVDDIO1
DVDDIO2
39
FER13
600
1206
40
47
53
AGND2
5
PPI0_D3
6
PPI0_D2
7
PPI0_D1
8
PPI0_D0
19
R39
33
0805
20
R41
33
0805
U10
1
21
4
VDEC_CLKOUT
2
22
SN74LVC1G32
SOT23-5
23
24
PVDD_ADV7183
32
33
27
C5
0.01UF
0805
26
25
2
C64
.082UF
0805
R1
1.5K
0805
37
2
VDEC_HS
1
VDEC_VS
80
VDEC_FIELD
69
VDEC_VREF
70
VDEC_HREF
16
SW2
11
12 ON
VENC_HS
12
11
R24
10K
0805
13
78
10
9
VENC_VS
77
8
79
7
1
2
3
4
5
PF3
6
PF2
PPI1_SYNC1
PPI0_SYNC1
PPI0_SYNC2
PPI1_SYNC2
PF[15:0]
DIP6
SWT017
55
C56
0.1UF
0805
PPI0_D4
AIN6
NC[DV]
48
76
3.3V
NC[AFF]
51
PPI0_D5
AIN4
VS
VIDEO_AVIN5
75
PPI0_D[15:0]
AIN8
LLC1
TP2
VIDEO_AVIN4
AIN2
PPI0_D6
1
AVIN5
74
2
AVIN4
PPI0_D7
3
66
AVIN1
73
4
28
XTAL
5
29
VDEC_27MHZ_CLK
6
AVIN1
AVIN4
AVIN5
U4
AGND2
FER14
600
1206
DNP
56
63
17
18
34
DVDD_ADV7183
1.8V
35
FER15
600
1206
30
10
72
FER17
600
1206
DNP
4
3.3V
3
SW2: Video Sync Signals and Encoder Enable Select
Defalut = OFF, OFF, OFF, OFF, OFF, ON
Position
Function
1-5
Connect video sync signals to DSP
ON = PF2 Used to enable or disable
6
the encoder digital interface
OFF = Encoder digital interface always disabled
15
AGND1
AGND2
DGND1
AGND3
DGND2
AGND4
DGND3
AGND5
DGND4
NC[AGND6]
DGND5
3
9
14
31
71
ADV7183AKST
LQFP80
PVDD_ADV7183
FER1
600
1206
A1.8V
FER2
600
1206
DNP
4
C55
0.1UF
0805
C3
0.01UF
0805
C73
0.1UF
0805
ANALOG
DEVICES
C74
0.01UF
0805
Title
Size
AGND2
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-BF561 EZ-KIT LITE
VIDEO DECODER (VIDEO IN)
Board No.
C
Date
20 Cotton Road
Rev
A0185-2003
2.0
Sheet
4-25-2006_16:26
D
10
of
14
A
B
C
D
3.3V
3.3V
3.3V
R248
10K
0805
PF5
R242
100
0805
3
1
R247
0
1206
U47
R98
10K
0805
SW6
SWT013
MOMENTARY
4
74LVC14A
SOIC14
R246
10K
0805
U47
1
CT25
1UF
A
U47
2
74LVC14A
SOIC14
13
1
12
5V
74LVC14A
SOIC14
3.3V
RESET
LED2
RED
LED001
POWER
LED1
GREEN
LED001
3.3V
R119
680
1206
R120
270
1206
3.3V
R249
10K
0805
PF6
R243
100
0805
R223
0
1206
U47
11
RESET
74LVC14A
SOIC14
U46
CT26
1UF
A
2
R229
10K
0805
10
SW7
SWT013
MOMENTARY
1
MR
4
PFI
SW1
SWT013
MOMENTARY
RESET
RESET
8
7
2
RESET
5
PFO
ADM708SARZ
SOIC8
3.3V
DA_SOFT_RESET
R250
10K
0805
PF7
R244
100
0805
R224
0
1206
U47
9
SW8
SWT013
MOMENTARY
8
74LVC14A
SOIC14
3.3V
CT27
1UF
A
C158
0.1UF
0805
C159
0.1UF
0805
PF[15:0]
11
PF5
SW4
2
11
PF6
6
PF7
4
9
PF8
5
8
TFS0
5
74LVC14A
SOIC14
10
4
5
3
3
R225
0
1206
U47
6
RSCLK0
6
CT28
1UF
A
PF5
2
R245
100
0805
SW9
SWT013
MOMENTARY
ON 12
R191
0
0805
DNP
P2
T1IN
T1OUT
T2IN
T2OUT
FER19
600
0603
14
FER20
600
0603
13
6
2
7
C148
0.1UF
0805
FER18
600
0603
UART
3
8
4
PF6
7
1
7
R1OUT
R1IN
9
8
R2OUT
R2IN
ADM3202ARNZ
SOIC16
R192
0
0805
FER21
600
0603
6
V-
12
RX
1
1
R251
10K
0805
PF8
10
3
2
V+
TX
2
IDC2X1
4
C2+
5
C2-
3.3V
P1
1
C147
0.1UF
0805
1
C1+
3
C1-
3
R184
0
0805
DNP
U21
9
RFS0
5
TSCLK0
DIP6
SWT017
DB9M
NOTE: Remove R192 when populating R191 and R184
SW4 PB Enable Switch
Default = ON, ON, ON, ON, OFF, OFF
Position
Function
Connects the push buttons to the Programmable Flags of the DSP
1-4
Useful if using the PFs for another purpose.
OFF, OFF = AD1836A -> TDM Mode
5,6
ON, ON = AD1836A -> I2S Mode
4
ANALOG
DEVICES
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-BF561 EZ-KIT LITE
RESET, PUSH-BUTTON SWITCHES, UART
Board No.
C
Date
20 Cotton Road
Rev
A0185-2003
2.0
Sheet
4-25-2006_13:36
D
11
of
14
A
B
C
D
EXPANSION INTERFACE (TYPE B)
5V
3.3V
D[31:0]
A[25:2]
J1
2
1
4
3
5V
1
A3
6
5
8
7
10
9
A4
A7
12
11
A6
A9
14
13
A8
16
15
MOSI
MISO
A10
A13
18
17
A12
A15
20
19
A14
A17
22
21
A16
PF5
A19
A21
24
23
26
25
28
27
A22
30
29
A24
PPI0_SYNC2
PF0
2
32
31
DT1SEC
34
33
DT1PRI
35
TFS1
38
37
TSCLK1
40
39
D0
DT0SEC
D3
42
41
D2
DT0PRI
D5
44
43
D4
TFS0
D7
46
45
D6
TSCLK0
D9
48
47
D8
D11
50
49
D10
D13
52
51
D12
D15
54
53
D14
D17
56
55
D16
D19
58
57
D18
62
61
D22
D25
64
63
D24
ABE3
D26
ABE2
PPI0_D[15:0]
D29
68
67
D28
ABE1
D31
70
69
D30
ABE0
PPI0_D0
72
71
PPI0_D2
74
73
PF14
PF[15:0]
3
65
76
75
AOE
EXP_PPI0_CLK
PPI0_D1
AWE
PPI0_D3
SMS2
SMS0
PF12
78
77
PF15
PF10
80
79
PF13
PF8
82
81
PF11
PF6
84
83
PF9
PF4
86
85
10
9
12
11
14
13
16
15
18
17
20
19
SCK
22
21
24
23
26
25
28
27
30
29
32
31
34
33
36
35
38
37
40
39
NMI0
7
PPI1_D2
10
9
PPI1_D3
PPI1_D4
12
11
PPI1_D5
PPI1_D7
PPI1_D8
16
15
PPI1_D9
PPI0_SYNC1
PPI1_D10
18
17
PPI1_D11
DR1SEC
PPI1_D12
20
19
PPI1_D13
DR1PRI
PPI1_D14
22
21
PPI1_D15
RFS1
24
23
RSCLK1
26
25
28
27
DR0PRI
30
29
RFS0
32
31
34
33
36
35
38
37
40
39
42
41
44
43
46
45
48
47
RESET
VDEC_HS
RSCLK0
PPI0_D6
VDEC_HREF
DSP_VDD_EXT
PPI0_D8
PPI1_SYNC2
PPI0_D10
54
53
PPI0_D14
PF2
56
55
PF3
SRAS
PF7
88
87
SA10
90
89
SWE
CON019
57
60
59
62
61
64
63
66
65
68
67
70
69
72
71
74
73
76
75
78
77
80
79
82
81
84
83
86
85
88
87
90
89
EXP_PPI1_CLK
CLK_OUT_EXP1
2
EXT_DSP_CLK
VDEC_VS
VDEC_VREF
DSP_3V_VOUT
PPI1_SYNC3
PPI1_SYNC1
PPI0_D12
PPI0_D15
58
RX
13
PPI0_D4
51
5
8
14
45
52
6
PPI1_D6
43
49
3
PPI1_D1
PPI0_SYNC3
46
50
4
DR0SEC
41
47
1
TX
44
48
J3
2
PPI1_D0
D20
D23
66
7
PPI0_D7
PF0
D27
8
PPI0_D5
PPI0_D13
59
1
PPI1_D[15:0]
VDEC_FIELD
PPI0_D11
60
5
42
PPI0_D9
D21
3
6
A20
A25
D1
4
A18
A23
36
1
A2
A5
A11
3.3V
J2
2
PF1
50
49
AMS3
52
51
AMS2
54
53
AMS1
56
55
AMS0
58
57
ARDY
60
59
ARE
62
61
SMS3
64
63
SMS1
66
65
68
67
70
69
72
71
SCKE
74
73
SCAS
76
75
CLK_OUT_EXP2
78
77
80
79
82
81
84
83
86
85
88
87
90
89
CON019
EXT_27MHZ_CLK
3
BR
BG
BGH
CON019
ANALOG
DEVICES
4
Title
Size
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-BF561 EZ-KIT LITE
EXTENDER CARD CONNECTORS
Board No.
C
Date
20 Cotton Road
Rev
A0185-2003
2.0
Sheet
4-25-2006_12:42
D
12
of
14
A
B
C
5V
F1
2.5A
FUS001
1
FER5
190
FER002
4
D3
2A
DO-214AA
3
1
2
UNREG_IN
3
INPUT
J7
D2
2A
DO-214AA
C160
1000PF
1206
2
R157
100K
1206
CT23
10UF
C
FER6
600
1206
2
OUTPUT1
4
OUTPUT2
GND
1
1
A5V
R163
0
1206
VR1
D
C122
0.1UF
0805
ADP3339AKCZ-5
SOT-223
UNREG_IN
A3V
1
3V_B
VR3
CT24
10UF
C
C29
0.1UF
0805
3
INPUT
3
7.5V_POWER
CON005
R73
0
1206
2
OUTPUT1
4
OUTPUT2
GND
1
FER16
600
1206
ADP3338AKCZ-33
SOT-223
C32
1UF
0805
CT17
10UF
C
C35
0.1UF
0805
C153
1000PF
1206
3.3V
NOTE: R252 or R253 gets populated
R83
0
0805
Default is R252 IN and R253 OUT
DSP_VDD_EXT
R252
0
0805
SHGND
DSP_VDD_INT
TP7
DSP_VDD_EXT
UNREG_IN
DSP_3V_VOUT
VR6
3
GND
1
CT20
10UF
C
R253
0
0805
DNP
2
OUTPUT1
4
OUTPUT2
INPUT
2
DSP_VCORE
R84
0
0805
U29
ADP3339AKCZ-33
SOT-223
C53
0.1UF
0805
CT21
10UF
C
R195
3.32K
0805
VROUT
L11
10UH
IND001
1
5
2
6
3
7
4
8
R82
0
0805
D7
2A
DO-214AA
CT22
68UF
D
D5
ZHCS1000
SOT23D
1A
2
DSP_VDD_INT
SO-8
C48
0.1UF
0805
3.3V
UNREG_IN
D4
100MA
SOD-323
R78
10K
0805
VR5
2
VIN
R79
0
0805
5
SHDN
C43
2.2UF
0805
C170
0.18UF
0805
1
L10
1.5UH
IND003
R74
0
0805
FB
6
SD
4
GND
VC
R180
17.4K
0805
6
D6
7
C46
2200PF
1206
2A
DO-214AA
C169
4.7UF
0805
1V2
1
VR2
7
IN1
8
IN2
R52
10K
0805
2
R75
53.6K
0805
3
5
FB
GND
4 ADP3336ARMZ
MSOP8
R77
0
0805
6
SD
C44
1UF
0805
C45
1UF
0805
R194
3.32K
0805
R186
10.0K
1206
OUT2
OUT3
3
SW
8
SYNC
LT1765
SOIC8
3
BOOST
OUT1
1.8V
R81
0
0805
DNP
3.3V
VR4
7
IN1
8
IN2
3.3V
CT18
10UF
C
FER4
600
1206
1
OUT1
2
OUT2
3
OUT3
5
FB
GND
4 ADP3336ARMZ
MSOP8
R48
76.8K
1206
C21
1UF
0805
R76
1M
0805
A1.8V
C24
1UF
0805
R56
147.0K
1206
CT19
100UF
C
3
MH6
MH7
MH8
FER3
600
1206
MH2
M1
M2
M3
M4
MH1
MH3
MH4
M5
MH5
TP8
TP5
TP11
TP10
TP6
TP4
TP9
SHGND
FER8
600
1206
RUBBER FOOTRUBBER FOOTRUBBER FOOTRUBBER FOOTRUBBER FOOT
MSC009
MSC009
MSC009
MSC009
MSC009
SHGND
SHGND
ANALOG
DEVICES
4
Board No.
C
Date
A
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-BF561 EZ-KIT LITE
POWER
Title
Size
20 Cotton Road
Rev
A0185-2003
2.0
Sheet
4-25-2006_12:42
D
13
of
14
A
B
C
D
DSP_VDD_EXT
DSP_VDD_INT
1
1
C137
0.01UF
0805
C140
0.01UF
0805
C49
0.01UF
0805
C174
0.01UF
0805
3.3V
C30
0.1UF
0805
C151
0.1UF
0805
C179
0.1UF
0805
3.3V
C126
0.1UF
0805
C135
0.1UF
0805
27MHZ OSC
U3
3.3V
C136
0.01UF
0805
5V
C134
0.01UF
0805
C168
0.01UF
0805
C37
0.1UF
0805
C31
10UF
1210
C50
10UF
1210
C47
10UF
1210
C173
0.01UF
0805
C154
0.01UF
0805
C145
0.1UF
0805
C172
0.1UF
0805
C178
0.1UF
0805
C152
0.1UF
0805
C157
0.01UF
0805
C156
0.01UF
0805
C183
0.1UF
0805
C22
0.1UF
0805
C138
0.01UF
0805
C52
0.1UF
0805
C164
0.1UF
0805
C139
0.1UF
0805
C171
0.1UF
0805
C177
0.1UF
0805
C184
0.1UF
0805
C185
0.01UF
0805
A5V
A5V
C107
0.22UF
0805
A5V
C162
0.22UF
0805
A5V
C143
0.22UF
0805
A5V
C129
0.22UF
0805
C186
0.01UF
0805
AGND
AGND
AGND
AGND
AGND
AGND
AD8606
U15
AD8606
U16
AD8606
U17
AD8606
U18
AD8606
U19
AD8606
U20
3V_B
3.3V
3.3V
C201
0.01UF
0805
C200
0.01UF
0805
C182
0.01UF
0805
C20
0.1UF
0805
A3V
C71
0.1UF
0805
SN74AHC1G08
U21
C75
0.01UF
0805
C85
0.1UF
0805
C125
0.22UF
0805
C70
0.01UF
0805
C83
0.1UF
0805
AGND2
AGND2
AD8061
U23
AD8061
U24
3.3V
3.3V
C106
0.22UF
0805
AGND
AGND
AD8606
U12
AD8606
U13
2
3.3V
AGND2
3.3V
A5V
A3V
AD8061
U22
3.3V
C41
0.01UF
0805
A5V
C256
0.01UF
0805
A3V
3.3V
C146
0.01UF
0805
74LVC14A
U10
3.3V
C104
0.22UF
0805
C167
0.1UF
0805
3.3V
SDRAM
U8
C108
0.22UF
0805
AGND
C176
0.01UF
0805
3.3V
ADSP-DM203
U1
A5V
C131
0.1UF
0805
AD1836
U14
3
C51
0.1UF
0805
M29W640D
U5
A5V
C19
0.1UF
0805
C175
0.1UF
0805
3.3V
IDT2305
U4
2
C155
0.1UF
0805
C69
0.01UF
0805
3.3V
C149
0.01UF
0805
C150
0.01UF
0805
ADG752
U25
3.3V
ADG752
U26
3
3.3V
DVDD_ADV7183
C101
0.01UF
0805
C114
0.01UF
0805
C91
0.1UF
0805
C89
0.1UF
0805
C102
0.1UF
0805
C90
0.1UF
0805
C109
0.1UF
0805
C110
0.1UF
0805
C113
0.01UF
0805
ADV7179
U27
C112
0.01UF
0805
C87
0.1UF
0805
C111
0.1UF
0805
C88
0.1UF
0805
C249
0.01UF
0805
ADM708SAR
U29
ADV7183
U28
C141
0.01UF
0805
ADM3202
U30
C181
0.01UF
0805
IDT74FCT3244APY
U31
C127
0.01UF
0805
IDT74FCT3244APY
U36
C165
0.01UF
0805
C166
0.01UF
0805
ADG752
U40
ADG752
U45
C27
0.1UF
0805
IDT2305
U46
C28
0.01UF
0805
C132
0.1UF
0805
39MHZ OSC
U54
3.3V
C189
0.1UF
0805
4
C191
0.1UF
0805
C202
0.01UF
0805
C203
0.01UF
0805
C190
0.01UF
0805
C187
0.01UF
0805
ANALOG
DEVICES
C188
0.01UF
0805
Size
A
Board No.
C
Date
B
C
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-BF561 EZ-KIT LITE
DECOUPLING CAPS
Title
SDRAM
U53
20 Cotton Road
Rev
A0185-2003
2.0
Sheet
4-25-2006_12:42
D
14
of
14
I
INDEX
A
B
A25-2 address bus pins, 2-3
AD1836A audio codecs, 1-11, 2-3, 2-4, 2-12
ADV7179 video encoders
video interface, 1-12
clock select jumper (JP1), 2-14
configuration switch (SW2), 2-10
PPI1 interface, 2-6, 2-7
programmable flags, 2-4
reset, 1-12
ADV7183A video decoders
video interface, 1-12
clock select switch (SW5), 2-13
configuration switch (SW2), 2-10
PPI0 interface, 2-6, 2-8
programmable flags, 2-4
reset, 1-12
AIN1/4/5 analog video channels, 2-8
~AMS0 memory select pins, 1-8
analog
audio interface, See SPORT0
video interface, See video interface
architecture, of this EZ-KIT Lite, 2-2
ASYNC (asynchronous memory control) banks,
1-7
audio
codecs, See AD1836A
connectors (J4-5), 2-19
enable switch (SW12), 2-13
interface, See SPORT
background telemetry channel (BTC), 1-14
bill of materials, A-1
BMODE1-0 (boot mode select) pins, 2-11
board schematics, B-1
boot mode select switch (SW3), 2-11
C
clock select switch, of PPIs (SW5), 2-13
codecs, See AD1836A
configuration, of this EZ-KIT Lite, 1-3
connectors
diagram of locations, 2-18
DB9 (UART), xii, 2-8
J1-3 (expansion), 2-9, 2-18
J4-5 (audio), 2-19
J6 (video), 2-19
J7 (power), 2-20
P2 (RS-232), xi, 2-20
P3 (SPORT1), 2-3, 2-20
P5 (SPI), 2-3, 2-14, 2-21
P9 (SPORT0), 2-20
ZP4 (JTAG), 2-21
contents, of this EZ-KIT Lite package, 1-2
core
clock rate, 2-2
frequency, 1-9
voltage, 2-2
customer support, xiv
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
I-1
INDEX
D
G
DAC A/B/C analog audio channels, 2-7
DB9 (UART) connector, xii, 2-8, 2-20, 2-21
default configuration, of this EZ-KIT Lite, 1-3
DIP switches
diagram of locations, 1-3, 2-10
SW10-11 (test), 2-13
SW2 (video config), 1-12, 2-8
SW4 (push button enable), 1-11, 2-12, 2-16
general-purpose IO pins, 1-10, 2-4, 2-12, 2-16
GND signals, 2-9
H
Help, online, xix
HSYNC signals, 2-6, 2-7
I
E
EBIU
address bus (A25-2) pins, 2-3
control signals, 2-3, 2-9
EBIU_SDBCTL register, 1-9
EBIU_SDGCTL register, 1-9
EBIU_SDRRC register, 1-9, 1-10
example programs, 1-13
expansion interface, 2-3, 2-8, 2-18
external bus interface unit, See EBIU
external memory
See also flash memory, SDRAM
map of, 1-7
via JTAG, 2-9
EZ-KIT Extender boards, 2-7
input clocks, 1-12, 2-2, 2-6, 2-7
installation, of this EZ-KIT Lite, 1-5
interfaces, See video, SPORT0, SPI, expansion
internal memory
See also SRAM
map of the processor, 1-8
IO voltage, 2-2
J
JTAG
connector (ZP4), 2-9, 2-21
emulation port, 2-9
jumpers
JP1 (ADV7179 clock select), 2-14
P1 (UART loop), 2-14
F
L
features, of this EZ-KIT Lite, x
FIELD (ADV7183A) control signal, 2-4, 2-8,
2-11
FIO0_FLAG_D registers, 1-10
FIO2_DIR register, 1-10
FIO2_FLAG_C/D/S/T registers, 1-10
flag pins, See programmable flags (PFs)
flash
memory, 2-3, 2-11
ports (PB47-32), 2-17
frequency, 1-9
LEDs
diagram of locations, 1-3, 2-15
LED13-20 (PF39-32), 1-10, 2-5, 2-17
LED1 (power), 2-16
LED2 (chip reset), 2-16
LED5-12 (PF47-40), 1-10, 2-5, 2-17
ZLED3 (USB monitor), 1-5, 2-17
license restrictions, 1-7
M
Media Instruction Set Computing (MISC), ix
I-2
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
INDEX
memory
map, of this EZ-KIT Lite, 1-7
select pins, See ~AMS2-0, ~SMS0
N
notation conventions, xxi
O
~OE (ADV7183A) signal, 2-4, 2-10
oscillators, 2-7, 2-13
P
P3 (SPORT0) connector, 2-3
package contents, 1-2
parallel peripheral interfaces (PPIs), 1-13, 2-6,
2-10, 2-18
See also PPI0, PPI1
PB47-32 flash ports, 2-17
power
connector (J7), 2-20
LED (LED1), 2-16
PPI0_D15-8 bits, 1-10, 2-5
PPI0 interface
to ADV7183A decoder, 1-12, 2-8
clock select pin, 2-7, 2-8
D15-8 bits, 2-17
D7-0 bits, 2-6
SYNC2-1 signals, 2-6, 2-8, 2-11
PPI0_SYNC2-1 synchronization signals, 2-8,
2-11
PPI1_D15-8 bits, 1-10, 2-5
PPI1 interface
to ADV7179 video encoder, 1-12, 2-7
clock select pin, 2-7
D15-8 bits, 2-17
D7-0 bits, 2-6, 2-7
HSYNC signals, 2-7
SYNC2-1 signals, 2-7, 2-11
PPI clock select switch (SW5), 1-12, 2-13
PPIxCLK signals, 2-13
programmable flags (PFs)
connections, 2-4
PF0 (video serial clock), 1-13, 2-4
PF1 (video serial data), 1-13, 2-4
PF2 (DV7183A enable), 1-13, 2-4, 2-10,
2-11
PF3 (ADV7183A field pin), 2-4, 2-8, 2-11
PF4 (AD1836A SPI select), 1-11, 2-3, 2-4
PF13 (ADV7183A reset), 1-12, 2-4
PF14 (ADV7179 reset), 1-12, 2-5
PF15 (AD1836A reset), 1-12, 2-5
PF16-20 (SPORT0), 2-5
PF21-25 (SPORT1), 2-5
PF26-27 (UART), 2-5
PF28-29 (SPORT0 serial clock), 2-5
PF30-31 (SPORT1 serial clock), 2-5
PF39-32 (LED13-20), 2-5
PF47-40 (LED5-12), 1-10, 2-5
PF5-8 (general-purpose IO), 1-10, 2-4, 2-12,
2-16
pull-down resistors, 1-12
pull-up resistors, 2-11
push buttons
See also switches by name (SWx), 1-10
diagram of locations, 2-15
enable switch (SW4), 2-12
R
RCA jacks, x, 2-19
registration, of this product, 1-3
reset
audio codec, 1-12
LED (LED2), 2-16
processor, 1-9
push buttons switch (SW1), 2-15
USB interface, 2-15
video encoder/decoder, 1-12, 2-4
restrictions, of the license, 1-7
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
I-3
INDEX
RFS0 signal, 1-11, 2-12
RS-232 connector (P2), xi, 2-8, 2-20
RSCLK0 signal, 1-11, 2-12
S
schematic, of this EZ-KIT Lite, B-1
SDRAM memory
connections, 2-3
control registers, 1-8
core MMRs, 1-8
data bank B SRAM, 1-8
data banks A, B SRAM, 1-8
default settings, 1-9
instruction SRAM, 1-8
instruction SRAM/CACHE, 1-8
optimum settings, 1-9
reserved, 1-8
scratch pad SRAM, 1-8
system MMRs, 1-8
serial
clock pin (SCL), 1-13, 2-4
data pin (SDAT), 1-13
video data, 2-4
serial peripheral interface (SPI), 2-3, 2-4, 2-12,
2-14
setup, of this EZ-KIT, 1-4
~SMS0 memory select pins, 1-8
SPIS1/SPISS signals, 2-14
SPORT
audio interface, 2-3
SPORT0
audio interface, xi, 1-11
connector (P3), 2-20
receive data secondary pin (PF20), 2-5
receive frame sync pin (PF19), 2-5
receive serial clock pin (PF28), 2-5
transmit data primary pin (PF18), 2-5
transmit data secondary pin (PF17), 2-5
transmit frame sync pin (PF16), 2-5
transmit serial clock pin (PF29), 2-5
I-4
SPORT1
receive data secondary pin (PF25), 2-5
receive frame sync pin (PF24), 2-5
receive serial clock pin (PF29), 2-5
transmit data primary pin (PF23), 2-5
transmit data secondary pin (PF22), 2-5
transmit frame pin (PF21), 2-5
transmit serial clock pin (PF31), 2-5
SRAM data bank A, 1-8
startup, of this EZ-KIT Lite, 1-5
SW10-11 (test) DIP switches, 2-13
SW12 (audio enable) switch, 2-13
SW13 (SPIS1/SPISS select) switch, 2-14
SW1 (reset) push button, 2-15
SW2 (video config) DIP switch, 1-12, 2-6, 2-7,
2-8, 2-11
SW3 (boot mode) switch, 2-11
SW4 (push button enable) DIP switch, 1-11,
2-12, 2-16
SW5 (PPI clock select) switch, 1-12, 2-6, 2-13
SW6-9 (general input) push buttons, 1-10, 2-4,
2-12, 2-16
synchronous dynamic random access memory,
See SDRAM
system
architecture, EZ-KIT Lite board, 2-2
clock (SCLK), 1-9
T
Target Options dialog box, 1-8
test DIP switches (SW10-11), 2-13
TFS0 signal, 1-11, 2-12
time-division multiplexed (TDM) mode, 1-11
timers11-8, 2-6
timers7-0, 2-4
TSCLK0 signal, 1-11, 2-12
two-wire interface (TWI) mode, 1-11, 1-13,
2-12
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
INDEX
U
V
UART
loop jumper (P1), 2-14
port, xii, 2-8
transmit/receive pins (PF26-27), 2-5
universal asynchronous receiver/transmitter, See
UART port
USB
cable, 1-3
interface, 2-9, 2-15, 2-21
monitor LED (ZLED3), 2-17
user LEDs (LED5-12, LED13-20), 2-17
video
channels, 2-7, 2-8
configuration switch (SW2), 2-10
connector (J6), 2-19
control signals, 2-7, 2-9
decoders, See ADV7183A
encoders, See ADV7179
input (PPI0), 2-8
interface, 1-12
output (PPI1), 2-7
VisualDSP++
documentation, xix
environment, 1-5
online Help, -xix
VSYNC signals, 2-7
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
I-5
INDEX
I-6
ADSP-BF561 EZ-KIT Lite Evaluation System Manual
Similar pages