ADSP-TS101S EZ-KIT Lite Manual (Rev. 2.1)

ADSP-TS101S EZ-KIT Lite®
Evaluation System Manual
Revision 2.1, April 2006
Part Number
82-000635-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106
a
Copyright Information
©2006 Analog Devices, Inc., ALL RIGHTS RESERVED. This document
may not be reproduced in any form without prior, express written consent
from Analog Devices, Inc.
Printed in the USA.
Limited Warranty
The EZ-KIT Lite evaluation system is warranted against defects in materials and workmanship for a period of one year from the date of purchase
from Analog Devices or from an authorized dealer.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by implication or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, TigerSHARC, VisualDSP++, the VisualDSP++
logo, CROSSCORE, the CROSSCORE logo, and EZ-KIT Lite are registered trademarks of Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.
Regulatory Compliance
The ADSP-TS101S EZ-KIT Lite evaluation system has been certified to
comply with the essential requirements of the European EMC directive
89/336/EEC (inclusive 93/68/EEC) and, therefore, carries the “CE”
mark.
The ADSP-TS101S EZ-KIT Lite evaluation system had been appended to
Analog Devices Development Tools Technical Construction File referenced “DSPTOOLS1” dated December 21, 1997 and was awarded CE
Certification by an appointed European Competent Body and is on file.
The EZ-KIT Lite evaluation system contains ESD
(electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate on the human
body and equipment and can discharge without
detection. Permanent damage may occur on devices
subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance
degradation or loss of functionality. Store unused
EZ-KIT Lite boards in the protective shipping
package.
CONTENTS
PREFACE
Purpose of This Manual ................................................................. xii
Intended Audience ......................................................................... xii
Manual Contents .......................................................................... xiii
What’s New in This Manual .......................................................... xiii
Technical or Customer Support ...................................................... xiv
Supported Processors ...................................................................... xiv
Product Information ....................................................................... xv
MyAnalog.com .......................................................................... xv
Processor Product Information ................................................... xv
Related Documents .................................................................. xvi
Online Technical Documentation ............................................ xvii
Accessing Documentation From VisualDSP++ .................... xviii
Accessing Documentation From Windows .......................... xviii
Accessing Documentation From Web ................................... xix
Printed Manuals ....................................................................... xix
VisualDSP++ Documentation Set ......................................... xix
Hardware Tools Manuals ...................................................... xix
Processor Manuals ................................................................. xx
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
v
CONTENTS
Data Sheets .......................................................................... xx
Notation Conventions ................................................................... xxi
USING ADSP-TS101S EZ-KIT LITE
Package Contents ......................................................................... 1-2
Default Configuration .................................................................. 1-3
Installation and Session Startup ..................................................... 1-5
Evaluation License Restrictions ..................................................... 1-7
Memory Map ............................................................................... 1-7
SDRAM Interface ......................................................................... 1-8
Programmable FLAG Pins ............................................................ 1-9
Interrupt Pins ............................................................................. 1-10
Flash Memory ............................................................................ 1-11
Audio Interface ........................................................................... 1-11
Example Programs ...................................................................... 1-12
Flash Programmer Utility ............................................................ 1-13
Handling ADSP-TS101S EZ-KIT Lite Flash Memory ............ 1-13
ADSP-TS101S EZ-KIT LITE HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
External Port ........................................................................... 2-3
Expansion Interface ................................................................. 2-3
JTAG Emulation Port ............................................................. 2-4
DIP Switch Settings ...................................................................... 2-4
Control Impedance Selection ................................................... 2-5
vi
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
CONTENTS
Drive Strength Selection .......................................................... 2-5
Boot Mode Settings ................................................................. 2-6
Interrupt Enable Settings ......................................................... 2-7
Clock Mode Settings ............................................................... 2-7
LEDs and Push Buttons ................................................................ 2-8
USB Monitor LED (LED1) ..................................................... 2-8
Reset LEDs (LED2, LED8–9) ................................................. 2-8
Power LED (LED3) ................................................................. 2-9
FLAG LEDs (LED4–7) ......................................................... 2-10
Reset Push Button (SW1) ...................................................... 2-10
Programmable FLAG Push Buttons (SW2, SW4–5, and SW9) 2-10
Interrupt Push Buttons (SW3 and SW6) ................................ 2-11
Connectors ................................................................................. 2-12
Audio (P2 and P3) ................................................................. 2-12
USB (P4) .............................................................................. 2-13
JTAG (P5) ............................................................................ 2-13
Expansion Interface (P11–13) ................................................ 2-14
Link Ports (P7–10) ................................................................ 2-14
Power Connector (P14) ......................................................... 2-15
Power Supply Specifications ........................................................ 2-15
ADSP-TS101S EZ-KIT LITE BILL OF MATERIALS
ADSP-TS101S EZ-KIT LITE SCHEMATIC
Title Page .................................................................................... B-1
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
vii
CONTENTS
Processor A ................................................................................... B-2
Processor B ................................................................................... B-3
SDRAM and Flash ....................................................................... B-4
Audio Interface ............................................................................. B-5
Audio In Amplifiers ...................................................................... B-6
Audio Out Amplifiers ................................................................... B-7
Push Buttons and LEDs ................................................................ B-8
Configuration ............................................................................... B-9
Expansion Connectors ................................................................ B-10
Power Supply .............................................................................. B-11
Caps ........................................................................................... B-12
INDEX
viii
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
PREFACE
Thank you for purchasing the ADSP-TS101S EZ-KIT Lite®, Analog
Devices (ADI) evaluation system for TigerSHARC® floating-point
embedded processors.
The TigerSHARC processor is a static super scalar (SSS) architecture targeted at software-defined radio applications. In these wireless
infrastructure applications, the TigerSHARC processor is replacing
field-programmable gate arrays (FPGAs) in the chip rate processing applications for third generation cellular. The performance, flexibility,
multiprocessing and IO capabilities of the TigerSHARC processor makes
it superior to FPGA implementations.
The evaluation board is designed to be used in conjunction with the VisualDSP++® development environment to test the capabilities of the
ADSP-TS101S TigerSHARC processor. The VisualDSP++ development
environment gives you the ability to perform advanced application code
development and debug, such as:
• Create, compile, assemble, and link application programs written
in C++, C, and ADSP-TS101S assembly
• Load, run, step-in, step-out, step-over, halt, and set breakpoints in
application program
• Profile programs
• Read and write data and program memory
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
ix
• Read and write core and peripheral registers
• Plot memory
Access to the ADSP-TS101S processor from a personal computer (PC) is
achieved through a USB port or an optional JTAG emulator. The USB
interface gives unrestricted access to the ADSP-TS101S processor and the
evaluation board peripherals. Analog Devices JTAG emulators offer faster
communication between the host PC and target hardware. Analog Devices
carries a wide range of in-circuit emulation products. To learn more about
Analog Devices emulators and processor development tools, go to
http://www.analog.com/dsp/tools/.
ADSP-TS101S EZ-KIT Lite provides example programs to demonstrate
the capabilities of the evaluation board.
ADSP-TS101S EZ-KIT Lite installation is part of the VisuL The
alDSP++ installation. The EZ-KIT Lite is a licensed product that
offers an unrestricted evaluation license for the first 90 days. For
details about evaluation license restrictions after the 90 days, refer
to “Evaluation License Restrictions” on page 1-7.
Refer to the VisualDSP++ Installation Quick Reference Card for details.
The board features:
• Two Analog Devices ADSP-TS101S processors
D
D
250 MHz core clock speed
Configurable core clock mode
• USB debugging interface
• Analog Devices AD1871 96 kHz analog-to-digital converter
(ADC)
D
x
Line-in 3.5 mm stereo jack
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Preface
• Analog Devices AD1854 96 kHz digital-to-analog converter
(DAC)
D
Line-out 3.5 mm stereo jack
• SDRAM memory
D
32 MB (4M byte x 64) DIMM
• Flash memory (544K x 8)
D
D
512K main flash memory
32K secondary flash memory
• Interface connectors
D
D
D
14-pin emulator connector for JTAG interface
Link port 0 and link port 1 for each processor
Expansion interface connectors (not populated)
• General-purpose IO
D
D
D
4 push button flags (two for each processor)
2 push button interrupts (one for each processor)
4 LED flag outputs (two for each processor)
• Analog Devices ADP3338, ADP3339, ADM660, and ADP3170
for voltage regulation
The EZ-KIT Lite board has two external memories: flash memory and
SDRAM. The flash memory can be used to store user-specific boot code.
By configuring the boot mode switch (SW7) and programming the flash
memory, the board can run as a stand-alone unit. For more information,
see “Memory Map” on page 1-7.
The EZ-KIT Lite board also contains an audio interface, facilitating creation of audio signal processing applications.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
xi
Purpose of This Manual
Additionally, the EZ-KIT Lite board provides expansion connectors,
allowing you to connect to the processor’s external port (EP).
Purpose of This Manual
The ADSP-TS101S EZ-KIT Lite Evaluation System Manual provides
instructions for installing the product hardware (board). The text
describes the operation and configuration of the board components and
provides guidelines for running your own code on the ADSP-TS101S
EZ-KIT Lite. Finally, a schematic and a bill of materials are provided as a
reference for future designs.
The product software installation is detailed in the VisualDSP++ Installation Quick Reference Card
Intended Audience
The primary audience for this manual is a programmer who is familiar
with Analog Devices processors. This manual assumes that the audience
has a working knowledge of the appropriate processor architecture and
instruction set. Programmers who are unfamiliar with Analog Devices
processors can use this manual but should supplement it with other texts
(such as the ADSP-TS101 TigerSHARC Processor Hardware Reference and
the ADSP-TS101 TigerSHARC Processor Programming Reference) that
describe your target architecture.
Programmers who are unfamiliar with VisualDSP++ should refer to the
VisualDSP++ online Help and user’s or getting started guides. For the
locations of these documents, see “Related Documents”.
xii
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Preface
Manual Contents
The manual consists of:
• Chapter 1. “Using ADSP-TS101S EZ-KIT Lite” on page 1-1
Provides information on the EZ-KIT Lite from a programmer’s
perspective and outlines the processor’s memory map.
• Chapter 2, “ADSP-TS101S EZ-KIT Lite Hardware Reference” on
page 2-1
Provides information on the hardware aspects of the evaluation
system.
• Appendix A,“ADSP-TS101S EZ-KIT Lite Bill Of Materials” on
page A-1
Provides a list of components used to manufacture the EZ-KIT
Lite board.
• Appendix B, “ADSP-TS101S EZ-KIT Lite Schematic” on
page B-1
Provides the resources to allow EZ-KIT Lite board-level debugging
or to use as a reference design.
B now is part of the online Help. The online Help viewL Appendix
ers should go to the PDF version of the ADSP-TS101S EZ-KIT
Lite Evaluation System Manual located in the Docs\EZ-KIT Lite
Manuals folder on the installation CD. Alternatively, the schematic
can be found on the Analog Devices Web site:
www.analog.com/processors.
What’s New in This Manual
This revision of the ADSP-TS101S EZ-KIT Lite Evaluation System Manual
has been updated for VisualDSP++ 4.5.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
xiii
Technical or Customer Support
Technical or Customer Support
You can reach Analog Devices, Inc. Customer Support in the following
ways:
• Visit the Embedded Processing and DSP products Web site at
http://www.analog.com/processors/technicalSupport
• E-mail tools questions to
[email protected]
• E-mail processor questions to
[email protected] (World wide support)
[email protected] (Europe support)
[email protected] (China support)
• Phone questions to 1-800-ANALOGD
• Contact your Analog Devices, Inc. local sales office or authorized
distributor
• Send questions by mail to:
Analog Devices, Inc.
One Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
USA
Supported Processors
This EZ-KIT Lite evaluation system supports the Analog Devices
ADSP-TS101S TigerSHARC embedded processors.
xiv
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Preface
Product Information
You can obtain product information from the Analog Devices Web site,
from the product CD-ROM, or from the printed publications (manuals).
Analog Devices is online at www.analog.com. Our Web site provides information about a broad range of products—analog integrated circuits,
amplifiers, converters, and digital signal processors.
MyAnalog.com
MyAnalog.com is a free feature of the Analog Devices Web site that allows
customization of a Web page to display only the latest information on
products you are interested in. You can also choose to receive weekly
e-mail notifications containing updates to the Web pages that meet your
interests. MyAnalog.com provides access to books, application notes, data
sheets, code examples, and more.
Registration:
Visit www.myanalog.com to sign up. Click Register to use MyAnalog.com.
Registration takes about five minutes and serves as means for you to select
the information you want to receive.
If you are already a registered user, just log on. Your user name is your
e-mail address.
Processor Product Information
For information on embedded processors and DSPs, visit our Web site at
www.analog.com/processors, which provides access to technical publications, data sheets, application notes, product overviews, and product
announcements.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
xv
Product Information
You may also obtain additional information about Analog Devices and its
products in any of the following ways.
• E-mail questions or requests for information to
[email protected] (World wide support)
[email protected] (Europe support)
[email protected] (China support)
• Fax questions or requests for information to
1-781-461-3010 (North America)
+49-89-76903-157 (Europe)
Related Documents
For information on product related development software, see the following publications.
Table 1. Related Processor Publications
Title
Description
ADSP-TS101S TigerSHARC Embedded
Processor Datasheet
General functional description, pinout, and timing
ADSP-TS101S TigerSHARC Processor
Hardware Reference
Description of internal processor architecture and
all register functions
TigerSHARC Processor Instruction Set Reference
Description of all allowed processor assembly
instructions
Table 2. Related VisualDSP++ Publications
Title
Description
VisualDSP++ User’s Guide
Description of VisualDSP++ features and usage
VisualDSP++ Assembler and Preprocessor
Manual
Description of the assembler function and commands
VisualDSP++ C/C++ Complier and
Description of the complier function and comLibrary Manual for TigerSHARC Processors mands for TigerSHARC processors
xvi
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Preface
Table 2. Related VisualDSP++ Publications (Cont’d)
Title
Description
VisualDSP++ Linker and Utilities Manual
Description of the linker function and commands
VisualDSP++ Loader and Utilities Manual
Description of the loader/splitter function and commands
you plan to use the EZ-KIT Lite board in conjunction with a
L IfJTAG
emulator, also refer to the documentation that accompanies
the emulator.
All documentation is available online. Most documentation is available in
printed form.
Visit the Technical Library Web site to access all processor and tools manuals and data sheets:
http://www.analog.com/processors/resources/technicalLibrary.
Online Technical Documentation
Online documentation comprises the VisualDSP++ Help system, software
tools manuals, hardware tools manuals, processor manuals, the Dinkum
Abridged C++ library, and Flexible License Manager (FlexLM) network
license manager software documentation. You can easily search across the
entire VisualDSP++ documentation set for any topic of interest. For easy
printing, supplementary .pdf files of most manuals are provided in the
Docs folder on the VisualDSP++ installation CD.
Each documentation file type is described as follows.
File
Description
.chm
Help system files and manuals in Help format
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
xvii
Product Information
File
Description
.htm or
.html
Dinkum Abridged C++ library and FlexLM network license manager software documentation. Viewing and printing the .html files requires a browser, such as
Internet Explorer 5.01 (or higher).
.pdf
VisualDSP++ and processor manuals in Portable Documentation Format (PDF).
Viewing and printing the .pdf files requires a PDF reader, such as Adobe Acrobat
Reader (4.0 or higher).
If documentation is not installed on your system as part of the software
installation, you can add it from the VisualDSP++ CD at any time by running the Tools installation. Access the online documentation from the
VisualDSP++ environment, Windows® Explorer, or the Analog Devices
Web site.
Accessing Documentation From VisualDSP++
To view VisualDSP++ Help, click on the Help menu item or go to the
Windows task bar and navigate to the VisualDSP++ documentation via
the Start menu.
To view ADSP-TS101S EZ-KIT Lite Help, which is part of the VisualDSP++ Help system, use the Contents or Search tab of the Help
window.
Accessing Documentation From Windows
In addition to any shortcuts you may have constructed, there are many
ways to open VisualDSP++ online Help or the supplementary documentation from Windows.
Help system files (.chm) are located in the Help folder, and .pdf files are
located in the Docs folder of your VisualDSP++ installation CD-ROM.
The Docs folder also contains the Dinkum Abridged C++ library and the
FlexLM network license manager software documentation.
xviii
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Preface
Your software installation kit includes online Help as part of the Windows® interface. These help files provide information about VisualDSP++
and the ADSP-TS101S EZ-KIT Lite evaluation system.
Accessing Documentation From Web
Download manuals at the following Web site:
http://www.analog.com/processors/resources/technicalLibrary/manuals.
Select a processor family and book title. Download archive (.zip) files,
one for each manual. Use any archive management software, such as WinZip, to decompress downloaded files.
Printed Manuals
For general questions regarding literature ordering, call the Literature
Center at 1-800-ANALOGD (1-800-262-5643) and follow the prompts.
VisualDSP++ Documentation Set
To purchase VisualDSP++ manuals, call 1-603-883-2430. The manuals
may be purchased only as a kit.
If you do not have an account with Analog Devices, you are referred to
Analog Devices distributors. For information on our distributors, log onto
http://www.analog.com/salesdir/continent.asp.
Hardware Tools Manuals
To purchase EZ-KIT Lite and in-circuit emulator (ICE) manuals, call
1-603-883-2430. The manuals may be ordered by title or by product
number located on the back cover of each manual.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
xix
Product Information
Processor Manuals
Hardware reference and instruction set reference manuals may be ordered
through the Literature Center at 1-800-ANALOGD (1-800-262-5643),
or downloaded from the Analog Devices Web site. Manuals may be
ordered by title or by product number located on the back cover of each
manual.
Data Sheets
All data sheets (preliminary and production) may be downloaded from the
Analog Devices Web site. Only production (final) data sheets (Rev. 0, A,
B, C, and so on) can be obtained from the Literature Center at
1-800-ANALOGD (1-800-262-5643); they also can be downloaded from
the Web site.
To have a data sheet faxed to you, call the Analog Devices Faxback System
at 1-800-446-6212. Follow the prompts and a list of data sheet code
numbers will be faxed to you. If the data sheet you want is not listed,
check for it on the Web site.
xx
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Preface
Notation Conventions
Text conventions used in this manual are identified and described as
follows.
Example
Description
Close command
(File menu)
Titles in reference sections indicate the location of an item within the
VisualDSP++ environment’s menu system (for example, the Close
command appears on the File menu).
{this | that}
Alternative required items in syntax descriptions appear within curly
brackets and separated by vertical bars; read the example as this or
that. One or the other is required.
[this | that]
Optional items in syntax descriptions appear within brackets and separated by vertical bars; read the example as an optional this or that.
[this,…]
Optional item lists in syntax descriptions appear within brackets
delimited by commas and terminated with an ellipse; read the example
as an optional comma-separated list of this.
.SECTION
Commands, directives, keywords, and feature names are in text with
letter gothic font.
filename
Non-keyword placeholders appear in text with italic style format.
L
Note: For correct operation, ...
A Note provides supplementary information on a related topic. In the
online version of this book, the word Note appears instead of this
symbol.
a
Caution: Incorrect device operation may result if ...
Caution: Device damage may result if ...
A Caution identifies conditions or inappropriate usage of the product
that could lead to undesirable results or product damage. In the online
version of this book, the word Caution appears instead of this symbol.
[
Warning: Injury to device users may result if ...
A Warning identifies conditions or inappropriate usage of the product
that could lead to conditions that are potentially hazardous for the
devices users. In the online version of this book, the word Warning
appears instead of this symbol.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
xxi
Notation Conventions
conventions, which apply only to specific chapters, may
L Additional
appear throughout this document.
xxii
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
1 USING ADSP-TS101S EZ-KIT
LITE
This chapter provides specific information to assist you with development
of programs for the ADSP-TS101S EZ-KIT Lite evaluation system.
The information appears in the following sections.
• “Package Contents” on page 1-2
Lists the items contained in your ADSP-TS101S EZ-KIT Lite
package.
• “Default Configuration” on page 1-3
Shows the default configuration of the ADSP-TS101S EZ-KIT
Lite.
• “Installation and Session Startup” on page 1-5
Instructs how to start a new or open an existing
ADSP-TS101SEZ-KIT Lite session using VisualDSP++.
• “Evaluation License Restrictions” on page 1-7
Describes the restrictions of the VisualDSP++ demo license
shipped with the EZ-KIT Lite.
• “Memory Map” on page 1-7
Describes the ADSP-TS101S EZ-KIT Lite board’s memory map.
• “SDRAM Interface” on page 1-8
Defines the register values needed to configure the external memory for SDRAM access.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
1-1
Package Contents
• “Programmable FLAG Pins” on page 1-9
Describes the function and use of the programmable FLAG pins on
the EZ-KIT Lite evaluation system.
• “Interrupt Pins” on page 1-10
Describes the function and use of the interrupt pins on the
EZ-KIT Lite evaluation system.
• “Flash Memory” on page 1-11
Describes how to program and use the flash memory.
• “Audio Interface” on page 1-11
Describes how to use and configure the audio interface.
• “Example Programs” on page 1-12
Provides information about the example programs included in the
ADSP-TS101S EZ-KIT Lite evaluation system.
• “Flash Programmer Utility” on page 1-13
Provides information on the Flash Programmer utility included
with VisualDSP++.
For information on the graphical user interface, including the boot loading, target options, and other facilities of the EZ-KIT Lite system, refer to
the online Help.
For detailed information about programming the ADSP-TS101S TigerSHARC processor, see the documents referred to as “Related
Documents”.
Package Contents
Your ADSP-TS101S EZ-KIT Lite evaluation system package contains the
following items.
• ADSP-TS101S EZ-KIT Lite board
1-2
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Using ADSP-TS101S EZ-KIT Lite
• VisualDSP++ Installation Quick Reference card
• CD containing:
D
D
D
D
D
VisualDSP++ software
ADSP-TS101S EZ-KIT Lite debug software
USB driver files
Example programs
ADSP-TS101S EZ-KIT Lite Evaluation System Manual (this
document)
• Universal 7.5V DC power supply
•
USB 2.0 cable
• Registration card (please fill out and return)
If any item is missing, contact the vendor where you purchased your
EZ-KIT Lite or contact Analog Devices, Inc.
Default Configuration
The EZ-KIT Lite evaluation system contains ESD
(electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate on the human
body and equipment and can discharge without
detection. Permanent damage may occur on devices
subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance
degradation or loss of functionality. Store unused
EZ-KIT Lite boards in the protective shipping
package.
The ADSP-TS101S EZ-KIT Lite board is designed to run outside your
personal computer as a stand-alone unit. You do not have to open your
computer case.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
1-3
Default Configuration
When removing the EZ-KIT Lite board from the package, handle the
board carefully to avoid the discharge of static electricity, which may damage some components. Figure 1-1 shows the default DIP switch,
connector locations, and LEDs used in installation. Confirm that your
board is set up in the default configuration before using the board.
Figure 1-1. EZ-KIT Lite Hardware Setup
1-4
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Using ADSP-TS101S EZ-KIT Lite
Installation and Session Startup
correct operation, install the software and hardware in the
L For
order presented in the VisualDSP++ Installation Quick Reference
Card.
1. Verify that the yellow USB monitor LED (LED1, located near the
USB connector) is lit. This signifies that the board is communicating properly with the host PC and is ready to run VisualDSP++.
2. If you are running VisualDSP++ for the first time, navigate to the
VisualDSP++ environment via the Start –> Programs menu. The
main window appears. Note that VisualDSP++ does not connect to
any session. Skip the rest of this step to step 3.
If you have run VisualDSP++ previously, the last opened session
appears on the screen. You can override the default behavior and
force VisualDSP++ to start a new session by pressing and holding
down the Ctrl key while starting VisualDSP++. Do not release the
Ctrl key until the Session Wizard appears on the screen. Go to
step 4.
3. To connect to a new EZ-KIT Lite session, start Session Wizard by
selecting one of the following.
• From the Session menu, New Session.
• From the Session menu, Session List. Then click New Session from the Session List dialog box.
• From the Session menu, Connect to Target. Then click
New Session from the Session List dialog box.
4. The Select Processor page of the wizard appears on the screen.
Ensure TigerSHARC is selected in Processor family. In Choose a
target processor, select ADSP-TS101. Click Next.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
1-5
Installation and Session Startup
5. The Select Connection Type page of the wizard appears on the
screen. Select EZ-KIT Lite and click Next.
6. The Select Platform page of the wizard appears on the screen.
In the Select your platform list, select ADSP-TS101S EZ-KIT
Lite via Debug Agent. In Session name, highlight or specify the
session name.
The session name can be a string of any length; although, the box
displays approximately 32 characters. The session name can
include space characters. If you do not specify a session name,
VisualDSP++ creates a session name by combining the name of the
selected platform with the selected processor. The only way to
change a session name later is to delete the session and to open a
new session.
Click Next.
7. The Finish page of the wizard appears on the screen. The page displays your selections. If you are satisfied, click Finish. If not, click
Back to make changes.
disconnect from a session, click the disconnect button
L Toor select
Session –> Disconnect from Target.
To delete a session, select Session –> Session List. Select the session name from the list and click Delete. Click OK.
1-6
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Using ADSP-TS101S EZ-KIT Lite
Evaluation License Restrictions
The ADSP-TS101S EZ-KIT Lite installation is part of the VisualDSP++
installation. The EZ-KIT Lite is a licensed product that offers an unrestricted evaluation license for the first 90 days. Once the initial
unrestricted 90-day evaluation license expires:
• VisualDSP++ allows a connection to the ADSP-TS101S EZ-KIT
Lite via the USB debug agent interface only. Connections to simulators and emulation products are no longer allowed.
• The linker restricts a users program to 96 KB of internal memory
for code space with no restrictions for data space.
Refer to the VisualDSP++ Installation Quick Reference Card for details.
Memory Map
The ADSP-TS101S processor has 6 M bits of internal memory that can be
used for program storage or data storage. The configuration of internal
memory is detailed in the ADSP-TS101 TigerSHARC Processor Hardware
Reference.
The ADSP-TS101S EZ-KIT Lite board contains 544K x 8-bits of external
flash memory. The memory is separated into two sections. One section
contains 512K bytes of main flash memory, and the other section contains
32K bytes of secondary flash memory. This memory is connected to the
processor’s ~BMS pin. The flash memory can be accessed in boot memory
space.
The board also contains one 4M x 64-bit SDRAM DIMM. This memory
is connected to the processor’s SDRAM interface.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
1-7
SDRAM Interface
Table 1-1. EZ-KIT Lite Evaluation Board Memory Map
Start Address
End Address
Content
0x0000 0000
0x0000 FFFF
Internal memory 0
0x0008 0000
0x0008 FFFF
Internal memory 1
0x0010 0000
0x0010 FFFF
Internal memory 2
0x0018 0000
0x0018 07FF
Internal registers
0x01C0 0000
0x01C0 FFFF
Broadcast
0x0200 0000
0x023F FFFF
Processor ID 0
0x0240 0000
0x027F FFFF
Processor ID 1
External Memory 0x0400 0000
0x047F FFFF
External memory space (SDRAM)
Internal Memory
SDRAM Interface
The DIMM shipped with the EZ-KIT Lite evaluation board is a 32 MB
module. You can upgrade to a 64 MB or 128 MB module. The module
must be a 168-pin DIMM PC100 device. Modules can be purchased from
such vendors as Viking, Infineon, or Crucial.
1.2 boards are shipped with 128 MB modules, but only
L Revision
32 MB of the 128 MB can be accessed, and the boards cannot be
upgraded with more memory. The issue is resolved in revision 1.3
boards.
To properly access SDRAM, the SYSCON and SDRCON registers must be configured properly. For the supplied DIMM, the SDRCON register should be
configured as follows: SDRAM enable, CAS latency of two cycles, pipe
depth of zero, page boundary of 256 words (1K words on revision 1.2
boards), refresh rate of every 1200 cycles (every 600 cycles on revision 1.2
boards), pre-charge to RAS of three cycles, RAS to pre-charge of four
cycles, and init sequence is MRS cycle follows refresh.
1-8
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Using ADSP-TS101S EZ-KIT Lite
When you are in a VisualDSP++ session and connected to the EZ-KIT
Lite board, the SDRAM registers are set to the default values automatically when a reset operation is performed. Clearing the corresponding
check box accessible through the Target Options dialog box, which is
accessible through the Settings pull-down menu, disables this feature. The
default values are:
•
SYSCON
= 0x001A79E7 and SDRCON = 0x00005223 (boards revision
1.2)
•
SDRCON
= 0x00005303 (boards revision 1.3 and greater)
and
registers define bus control configuration.
[ The
They can be written only once after reset and cannot be changed
SYSCON
SDRCON
during system operation.
Programmable FLAG Pins
Each ADSP-TS101S processor has four programmable flag pins. Two flag
pins from each processor (FLAG0 and FLAG1) allow you to interact with the
running program through the use of a switch (SW2, SW4–5, and SW9). The
FLAG2 and FLAG3 connect to the LEDs (LED4–5 and LED6–7).
After the processor is reset, the programmable flags are configured as
inputs. The direction of each programmable flag is configured in the
SQCTL register. If the flag is configured for output, the value is set in the
SQCTL register. If the flag is configured for input, the value on the flag pin
is read from the SQSTAT register. Programmable flags are summarized in
Table 1-2. For more information on configuring the programmable flag
pins, see the ADSP-TS101 TigerSHARC Processor Hardware Reference.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
1-9
Interrupt Pins
Table 1-2. Programmable FLAG Pin Summary
FLAG Pin
Connection
Description
FLAG0_A
SW4
FLAG1_A
SW9
The FLAG0 and FLAG1 pins connect to the push buttons
to supply feedback for program execution. For instance,
you can write your code to trigger a routine when the
push button is pressed.
FLAG0_B
SW5
FLAG1_B
SW2
FLAG2_A
LED7
FLAG3_A
LED6
FLAG2_B
LED4
FLAG3_B
LED5
The FLAG2 and FLAG3 pins connect to the LEDs to supply feedback during program execution.
Interrupt Pins
The ADSP-TS101S processor has four interrupt pins (IRQ3-0) that allow
you to interact with the running program. One external interrupt from
each processor is directly accessible through the push button switches (SW3
and SW6) on the EZ-KIT Lite board. Interrupts are summarized in
Table 1-3. For more information on configuring the interrupt pins, see
the ADSP-TS101 TigerSHARC Processor Programming Reference.
Table 1-3. Interrupt Pin Summary
Interrupt Pin
Connection
Description
IRQ0_A
SW3
IRQ0_B
SW6
The IRQ0 interrupt connects to push the buttons to supply feedback for program execution. For instance, you
can write your code to perform a different function when
an interrupt is detected.
1-10
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Using ADSP-TS101S EZ-KIT Lite
Flash Memory
The DSM2150 flash/PLD chip provides a total of 544K x 8-bits of external flash memory, arranged into two independent flash arrays (main and
secondary). The chip also has a series of configuration registers to control
IO and PLD. The memory chip is initially configured with the memory
sectors mapped to the processor, as shown in Figure 1-1 on page 1-8.
The DSM2150 can be re-programmed using the FlashLINK JTAG programming cable available from STMicroelectronics (www.st.com/psd).
FlashLINK plugs into any PC parallel port. The software development
tool, PSDsoft Express™, is required to modify the DSM2150 configuration and operate the FlashLINK cable. PSDsoft Express can be
downloaded at no charge from the same Web site.
Audio Interface
The audio interface allows you to interface to the board’s analog-to-digital
converter (ADC) and digital-to-analog converter (DAC). See “Audio (P2
and P3)” on page 2-12 for more information about the connectors. The
audio interface consists of two main ICs: AD1871 and AD1854.
The AD1871 is a stereo audio ADC intended for digital audio applications requiring high-performance analog-to-digital conversion. The
AD1871 provides 97 dB THD+N and 107 dB dynamic range.
The AD1854 is a high-performance, single-chip stereo, audio DAC delivering 113 dB dynamic range and 112 dB SNR at a 48 kHz sample rate.
Because the ADSP-TS101S processor does not have any SPORTs, a Xilinx
field-programmable gate array (FPGA) generates the audio interface control signals between the processor and the audio circuit. Setting the FLAG3
signal of DSP_A high enables the audio interface inside of the FPGA. Once
the audio interface has been enabled, the audio data can be transferred to
and from the processor by generating a DMAR0 cycle. The audio data interADSP-TS101S EZ-KIT Lite Evaluation System Manual
1-11
Example Programs
faces with the processor via the lowest 24 bits of the data bus (D23-0).
Refer to the audio example program included in the EZ-KIT Lite installation directory for more information on how to use the interface.
Example Programs
Example programs are provided with the ADSP-TS101S EZ-KIT Lite to
demonstrate various capabilities of the evaluation board. These programs
are installed with the EZ-KIT Lite software in the …\TS\Examples\ADSP-TS101 EZ-KIT Lite subdirectory of the VisualDSP++
installation directory. Please refer to the readme file provided with each
example program for more information.
the examples, do not change these bits:
[• When orrunning(bits
8 or 9) in the
register
DBGEN
•
DBG
NMOD
SQCTL
(bit 31) in the IMASKH register.
The change can disable communications with the host.
1-12
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
Using ADSP-TS101S EZ-KIT Lite
Flash Programmer Utility
The ADSP-TS101S EZ-KIT Lite evaluation system includes a Flash Programmer utility. The utility allows you to program the flash memory on
the EZ-KIT Lite. The Flash Programmer is installed with VisualDSP++.
Once the utility is installed, it is accessible from the Tools pull-down
menu.
Handling ADSP-TS101S EZ-KIT Lite Flash Memory
When the entire flash memory contents is erased using the Flash Programmer (under Advanced Options), you cannot bring up the IDDE and open
an ADSP-TS101S EZ-KIT session.
The following workaround brings the IDDE running again:
1. Power down the EZ-KIT Lite.
2. Move DIP switch 7 into the OFF position.
3. Power the EZ-KIT Lite board.
4. Start the IDDE.
5. Use the Flash Programmer from the Tools pull-down menu to load
a valid program into the flash memory, such as an example program from the …\TS\Examples\ADSP-TS101 EZ-KIT Lite directory.
For more information on the Flash Programmer utility, refer to online
Help.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
1-13
Flash Programmer Utility
1-14
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
2 ADSP-TS101S EZ-KIT LITE
HARDWARE REFERENCE
This chapter describes the hardware design of the ADSP-TS101S EZ-KIT
Lite board. The following topics are covered.
• “System Architecture” on page 2-2
Describes the configuration of the ADSP-TS101S EZ-KIT Lite
evaluation board and explains how the board components interface
with the processor.
• “DIP Switch Settings” on page 2-4
Shows the location and describes the function of the configuration
DIP switch.
• “LEDs and Push Buttons” on page 2-8
Shows the location and describes the function of the LEDs and
push buttons.
• “Connectors” on page 2-12
Shows the location of and gives the part number for all of the connectors on the board. In addition, provides the manufacturer and
part number information for the mating parts.
• “Power Supply Specifications” on page 2-15
Describes the power connector.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
2-1
System Architecture
System Architecture
This section describes the processor’s configuration on the EZ-KIT Lite
board.
Figure 2-1. System Architecture
The EZ-KIT Lite has been designed to demonstrate the capabilities of the
ADSP-TS101S TigerSHARC processor. The processor core voltage is
1.25V. The external interface operates at 3.3V.
An 83.33 MHz SMT oscillator supplies the input clock to the processor.
The speed at which the core operates is determined by the settings of the
processor switch SW7. For more information, see “Clock Mode Settings”
on page 2-7. By default, the processor core runs at 250 MHz
(83.3 MHz x 3).
2-2
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
ADSP-TS101S EZ-KIT Lite Hardware Reference
External Port
The external port is connected to a 544K x 8-bit flash memory. The flash
memory connects to the boot memory select pin (~BMS), allowing the
memory to be used to boot the processor as well as to store information
during normal operation. Refer to “Memory Map” on page 1-7 for information about the location of the flash memory on the processor’s memory
map.
The external port is also connected to a 4MB x 64-bit SDRAM DIMM.
Refer to “SDRAM Interface” on page 1-8 for information on how to configure the SDRAM registers.
Expansion Interface
The expansion interface consists of three connectors (P1–3). The following
table shows the interfaces each connector provides. For the exact pinout of
the expansion connectors, refer to “ADSP-TS101S EZ-KIT Lite Schematic” on page B-1.
Table 2-1. Expansion Connector Interfaces
Connector
Interfaces
P11
5V, GND, address, data
P12
3.3V, GND, SDRAM control signals, flags, IRQs, timers
P13
GND,
reset, DMA, memory control, CLKOUT, PSD IO signals
When using the expansion interface, limits to the current and to the interface speed must be taken into consideration. The maximum current limit
depends on the regulator capabilities. Additional circuitry can also add
extra loading to signals, decreasing their maximum effective speed.
Devices does not support and is not responsible for the
L Analog
effects of additional circuitry.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
2-3
DIP Switch Settings
JTAG Emulation Port
The JTAG emulation port allows an emulator to access the processor’s
internal and external memory, as well as the special function registers
through a 14-pin header. See “JTAG (P5)” on page 2-13 for more information about the JTAG connector. To learn more about available
emulators, contact Analog Devices as described in “Processor Product
Information”.
DIP Switch Settings
This section describes the function of the DIP switch, SW7. Figure 2-2
shows the location of the switch.
Figure 2-2. Switch Location
2-4
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
ADSP-TS101S EZ-KIT Lite Hardware Reference
Control Impedance Selection
Positions 3 through 1 (CONTROLIMP2-0) of SW7 determine the impedance for
the ADC (address/data/controls) and LINK (all link port outputs). Refer to
the ADSP-TS101S TigerSHARC processor data sheet at http://www.analog.com/UploadedFiles/Data_Sheets/40196385778873ADSP_TS101S_b.pd
f
for more information.
Table 2-2. Control Impedance Selection
SW7
Position 3
SW7
Position 2
SW7
Position 1
ON
ON
ON
ON
ADC
Link
dig_ctrl
pulse
dig_ctrl
pulse
ON
0
X
0
X
OFF
0
X
0
X
ON
ON
0
X
1
0
ON
OFF
0
X
1
1
OFF
ON
ON
1
0
0
X
OFF
ON
OFF
1
1
0
X
OFF1
OFF
ON
1
0
1
0
OFF
OFF
OFF
1
1
1
1
1
Default settings
Drive Strength Selection
Positions 6 through 4 (DS2-0) of SW7 determine the digital drive strength.
Refer to the ADSP-TS101S TigerSHARC processor data sheet at
http://www.analog.com/UploadedFiles/Data_Sheets/40196385778873ADSP_TS101S_b.pdf
for more
information.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
2-5
DIP Switch Settings
Table 2-3. Drive Strength Selection
SW7 Position 6
SW7 Position 5
SW7 Position 4
Drive Strength
ON
ON
ON
11%
ON
ON
OFF
29%
ON
OFF
ON
37%
ON
OFF
OFF
49%
OFF
ON
ON
62%
OFF
ON
OFF
75%
OFF
OFF
ON
88%
OFF1
OFF
OFF
100%
1
Default settings
Boot Mode Settings
Position 7 of SW7 determines how the processor boots. Table 2-4 shows
the setting for the boot modes. Refer to the ADSP-TS101S TigerSHARC
processor data sheet at http://www.analog.com/UploadedFiles/Data_Sheets/40196385778873ADSP_TS101S_b.pdf for more
information.
Table 2-4. Boot Mode Settings
SW7 Position 7
Boot Mode
ON1
EPROM BOOT
OFF
External Boot
1
2-6
Default settings
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
ADSP-TS101S EZ-KIT Lite Hardware Reference
Interrupt Enable Settings
Position 8 of SW2 determines how the processor handles interrupts.
Table 2-5 shows the setting for the interrupt modes. Refer to the
ADSP-TS101S TigerSHARC processor data sheet at http://www.analog.com/UploadedFiles/Data_Sheets/40196385778873ADSP_TS101S_b.pd
f
for more information.
Table 2-5. Interrupt Enable Settings
SW2 Position 8
Interrupt Enable Mode
ON1
Level-sensitive mode
OFF
Edge-sensitive mode
1
Default settings
Clock Mode Settings
Positions 9 through 11 (LCLKRAT2-0) of SW7 determine the ADSP-TS101S
processor’s core speed. The frequency supplied to CLKIN of the processor
may be changed by replacing the 83.33 MHz oscillator (U28) shipped with
the board with a different oscillator. Ensure that the selected clock mode
and frequency do not exceed the minimum and maximum specifications
of the ADSP-TS101S processor.
Table 2-6 shows the jumper settings for the clock modes. For more information on the clock modes, see the ADSP-TS101S processor data sheet at
http://www.analog.com/UploadedFiles/Data_Sheets/40196385778873ADSP_TS101S_b.pdf.
Table 2-6. Clock Mode Settings
SW7 Position 11
SW7 Position 10
SW7 Position 9
Ratio
ON
ON
ON
2
ON
ON
OFF
2.5
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
2-7
LEDs and Push Buttons
Table 2-6. Clock Mode Settings (Cont’d)
SW7 Position 11
SW7 Position 10
SW7 Position 9
Ratio
ON1
OFF
ON
3
ON
OFF
OFF
3.5
OFF
ON
ON
4
OFF
ON
OFF
5
OFF
OFF
ON
6
OFF
OFF
OFF
RSVD
1
Default settings
LEDs and Push Buttons
This section describes the function of the LEDs and push buttons.
Figure 2-3 shows the locations of the LEDs and push buttons.
USB Monitor LED (LED1)
The USB monitor LED, LED1, indicates that USB communication has
been initialized successfully, allowing you to connect to the processor
using VisualDSP++. If the LED is not lit, try resetting the board and/or
reinstalling the USB driver.
VisualDSP++ is actively communicating with the EZ-KIT
L When
Lite target board, the LED can flicker, indicating communications
handshake.
Reset LEDs (LED2, LED8–9)
When LED2 is lit, the USB interface is being reset. The USB interface is
reset only when it is not configured. Once the USB interface has been
configured, you must remove power to reset.
2-8
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
ADSP-TS101S EZ-KIT Lite Hardware Reference
Figure 2-3. LEDs and Push Button Locations
When LED8 is lit, it indicates that the master reset of all the major ICs is
active.
When LED9 is lit, the two ADSP-TS101S processors (U1 and U2) are being
reset. The USB interface resets the ADSP-TS101S processor during USB
communication initialization.
Power LED (LED3)
The green LED, LED3, indicates that power is being properly supplied to
the board.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
2-9
LEDs and Push Buttons
FLAG LEDs (LED4–7)
The flag LEDs connect to the processor’s flag pins (FLAG2 and FLAG3).
These LEDs are active high and are lit by an output of “1” from the processor. Refer to “SDRAM Interface” on page 1-8 for more information on
how to utilize the flags when programming the processor. Table 2-7 shows
the FLAG signals and the corresponding LEDs.
Table 2-7. FLAG LEDs
FLAG Pin
LED Reference Designator
FLAG2_A
LED7
FLAG3_A
LED6
FLAG2_B
LED4
FLAG3_B
LED5
Reset Push Button (SW1)
The RESET push button, SW1, resets all the ICs on the board, except the
USB interface after it has been configured.
Programmable FLAG Push Buttons (SW2, SW4–5,
and SW9)
Four push buttons are provided for general-purpose user input. The SW2,
SW4, SW5, and SW9 push buttons connect to the processor’s programmable
FLAG pins. The push buttons are active high and when pressed, send a
high (1) to the processor. Refer to “SDRAM Interface” on page 1-8 for
more information on how to use the flags when programming the processor. Table 2-8 shows the flag signals and the corresponding switches.
2-10
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
ADSP-TS101S EZ-KIT Lite Hardware Reference
Table 2-8. FLAG Push Buttons
FLAG Pin
Push Button Reference Designator
FLAG0_A
SW4
FLAG1_A
SW9
FLAG0_B
SW5
FLAG1_B
SW2
Interrupt Push Buttons (SW3 and SW6)
Two push buttons, SW3 and SW6, are provided for user input. The push
buttons connect to the processor’s interrupt pins. The push buttons are
active low and, when pressed, send a low (0) to the processor. Refer to
“SDRAM Interface” on page 1-8 for more information on how to use the
push buttons when programming the processor. Table 2-9 shows the
interrupt signals and corresponding switches.
Table 2-9. Interrupt Push Buttons
FLAG Pin
Push Button Reference
Designator
FLAG Pin
Push Button Reference
Designator
IRQ0_A
SW3
IRQ0_B
SW6
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
2-11
Connectors
Connectors
This section describes the connector functionality and provides information about mating connectors. The locations of the connectors are shown
in Figure 2-4.
Figure 2-4. Connector Locations
Audio (P2 and P3)
There are two 3.5 mm stereo audio jacks.
Part Description
Manufacturer
Part Number
3.5 mm stereo jack
SHOGYO
SJ-0359AM-5
2-12
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
ADSP-TS101S EZ-KIT Lite Hardware Reference
Part Description
Manufacturer
Part Number
Mating Connector
3.5 mm stereo plug to 3.5 mm ste- RADIO SHACK
reo cable
L12-2397A
USB (P4)
The USB connector is a standard type B USB receptacle.
Part Description
Manufacturer
Part Number
Type B USB receptacle
MILL-MAX
897-30-004-90-000
DIGI-KEY
ED90003-ND
Mating Connector
USB cable (provided with the kit)
ASSMAN
AK672-5
DIGI-KEY
AK672-5ND
JTAG (P5)
The JTAG header is the connecting point for a JTAG in-circuit emulator
pod.
3 is missing to provide keying. Pin 3 in the mating connector
L Pin
should have a plug. When an emulator is connected to the JTAG
header, the USB debug interface is disabled.
using an emulator with the EZ-KIT Lite board, follow the
[ When
connection instructions provided with the emulator.
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
2-13
Connectors
Expansion Interface (P11–13)
Three board-to-board connector footprints provide signals for most of the
processor’s peripheral interfaces. The connectors are located at the bottom
of the board. For more information about the interface, see “Expansion
Interface” on page 2-3. For availability and pricing of the P11, P12, and
P13 connectors, contact Samtec.
Part Description
Manufacturer
Part Number
90-position 0.05” spacing
SAMTEC
SFM-145-02-S-D
Mating Connectors
90-position 0.05” spacing
(through hole)
SAMTEC
TFM-145-x1 series
90-position 0.05” spacing
(surface mount)
SAMTEC
TFM-145-x2 series
90-position 0.05” spacing
(low cost)
SAMTEC
TFC-145 series
Link Ports (P7–10)
Two link ports from each processor connect to a 26-pin connector. Refer
to EE-106 at http://www.analog.com/UploadedFiles/Application_Notes/24075233ee_106.pdf for more information
about the link port connectors. EE-106 discusses the link port assignments for ADSP-211xx SHARC processor applications.
In a TigerSHARC processor application, the link port cable connectors
require pins 12 and 13 to be populated. The correct TigerSHARC link
port cable assembly can be obtained from TransTech DSP (TTC44-30).
The associated Gore Coaxial cable (DXN2132) should also be revised for
the proper number of strands to include connector pins 12 and 13.
2-14
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
ADSP-TS101S EZ-KIT Lite Hardware Reference
Part Description
Manufacturer
Part Number
26-position connector
TRANSTECH DSP
TTC44-30
Mating Connectors
Cable connector
HONDA
RMCA-E26F1S-A
Shroud
HONDA
RMCA-E26L1A
Coaxial cable
GORE
DXN2132
Power Connector (P14)
The power connector provides all of the power necessary to operate the
EZ-KIT Lite board.
Part Description
Manufacturer
Part Number
2.5 mm power jack (P14)
SWITCHCRAFT
RAPC712
DIGI-KEY
SC1152-ND
Mating Power Supply (shipped with the EZ-KIT Lite)
7.5V power supply
GLOBTEK
TR9CC2000LCP-Y
Power Supply Specifications
The power connector supplies DC power to the EZ-KIT Lite board.
Table 2-10 shows the power connector pinout.
Table 2-10. Power Connectors
Terminal
Connection
Center pin
+7.5 VDC@2 amps
Outer ring
GND
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
2-15
Power Supply Specifications
2-16
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
A ADSP-TS101S EZ-KIT LITE BILL
OF MATERIALS
The bill of materials corresponds to “ADSP-TS101S EZ-KIT Lite Schematic” on page B-1. Please check the latest schematic on the Analog
Devices Web site:
http://www.analog.com/Processors/Processors/DevelopmentTools/tec
hnicalLibrary/manuals/DevToolsIndex.html#Evaluation%20Kit%20Manuals.
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
1
3
0.00 1/4W 5%
R137,R142–143
YAGEO
0.0QBK-ND
2
1
3.3V-OCTALBUFFER
U32
TI
SN74LVT244BDW
3
1
HEX-INVER-SCH
MITT-TRIGGER
U24
TI
74LVC14AD
4
1
3.3V-OCTALBUFFER
U27
IDT
IDT74FCT3244APY
5
1
3.3V 1-10 CLOCK
DRIVER
U29
IDT
IDT74FCT3807AQ
6
1
USB-TX/RX
MICROCONTROLLER
U13
CYPRESS
CY7C64603-128NC
7
1
NPN TRANSISTOR 200MA
Q3
FAIRCHILD
MMBT4401
8
1
128K X 8 SRAM
U16
CYPRESS
CY7C1019BV33-12VC
9
1
12.0MHZ
CRYSTAL
Y1
DIG01
300-6027-ND
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
A-1
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
10
1
XILINXSPARTAN2-FPGA
U19
XILINX
XC2S200-6FG256C
11
8
SINGLE-2INPUT-NAND
U5–6, U15, U26,
U35–U38
TI
SN74AHC1G00DBVR
12
1
N-CHANNELMOSFET
Q2
FAIRCHILD
FDS6982
13
1
POWER MOSFET
Q1
IR
IRFR024
14
1
12.288MHZ
OSCILLATOR
U9
DIG01
SG-8002CA-PCC-ND
15
1
2N7002
Q5
FAIRCHILD
2N7002
16
1
MMBT3904
Q4
FAIR CHILD
MMBT3904
17
2
256Kx16 SRAM
U20, U21
GSI TECHNOLOGY
GS74116TP-10
18
1
FLASH MEMORY
U4
STMICRO
DSM2150F5V
19
1
32K EEPROM
U14
MICROCHIP
24LC32A-I/SN
20
1
83.33MHZ
OSCILLATOR
U28
DIG01
SG-8002CA-PCC-ND
21
1
FLASH MEMORY
U22
ST MICRO
DSM2150F5V
22
38
0.01uF 100V 10%
CERM
C46–47, C52–53,
C58–59, C64–65,
C74–81, C94–97,
C121–128,
C136–142,
C156–157, C161
AVX
12061C103KAT050M
23
2
1000pF 50V 5%
CERM
C84–85
AVX
12065A102JAT2A
24
1
150pF 50V 5%
CERM
C13
AVX
12065A151JAT2A
25
2
2200pF 50V 5%
NPO
C19, C41
AVX
12065A222JAT2A
A-2
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
ADSP-TS101S EZ-KIT Lite Bill Of Materials
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
26
1
0.1uF 50V 20%
CERM
C16
AVX
12065E104MAT2A
27
1
VOLTAGESUPERVISOR
U25
ANALOG
DEVICES
ADM708SAR
28
1
2.5V-1.0AMP
REGULATOR
VR1
ANALOG
DEVICES
ADP3338AKC-2.5
29
1
5V-1.5A
REGULATOR
VR2
ANALOG
DEVICES
ADP3339AKC-5-REEL
30
3
DUAL AUDIO OP
AMP
U10–12
ANALOG
DEVICES
SSM2275S
31
2
ADSP-TS101SKB21
80
U1–2
ANALOG
DEVICES
ADSP-TS101SKB2180
32
1
STERO-DAC
U8
ANALOG
DEVICES
AD1854JRS
33
1
STERO-ADC
U7
ANALOG
DEVICES
AD1871YRS
34
1
SWITCHED-VOLT
-CONVERTER
U30
ANALOG
DEVICES
ADM660AR
35
1
SINGLE-PHASECORE-CONTROL
U31
ANALOG
DEVICES
ADP3170
36
1
4.7uF 25V 10%
TANT
CT10
AVX
TAJC475K025R
37
1
PWR 2.5MM_JACK
P14
SWITCHCRAFT
SC1152-ND12
38
1
USB 4PIN
P4
MILL-MAX
897-30-004-90-000000
39
4
LNKPRT 12X2
P7–10
HONDA
(TSUSHINK)
RMCA-EA26LMY0M03-A
40
7
SPST-MOMENTARY 6MM
SW1–6, SW9
PANASONIC
EVQ-PAD04M
41
1
DIP12
SW7
DIGI-KEY
CKN3063-ND
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
A-3
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
42
1
IDC 7X2
P1
MOLEX
70247-1401
43
1
168PIN DIMM
U3
MOLEX
71251-0012
44
1
7A FAST-ACTING
F1
DIG01
283-2438-2-ND
45
13
0.00 1/8W 5%
R19, R23, R34,
R49–51, R54–55,
R131, R133–134,
R141
YAGEO
0.0ECT-ND
46
1
220uF 10V 20%
ELEC
CT14
SPRAGUE
293D227X9010E2T
47
5
AMBER-SMT
GULL-WING
LED1, LED4–7
PANASONIC
LN1461C-TR
48
2
330pF 50V 5%
NPO
C20, C26
AVX
08055A331JAT
49
4
0.01uF 100V 10%
CERM
C10, C165, C167,
C168
AVX
08051C103KAT2A
50
86
0.1uF 50V 10%
CERM
C1, C9, C17,
C42–45, C48–51,
C54–57, C60–63,
C66–73, C82–83,
C86–93, C98–120,
C129–135,
C143–155,
C158–160, 162,
C172, C173
AVX
08055C104KAT
51
9
0.001uF 50V 5%
NPO
C4–6, C12, C28,
C30, C32–33,
C164
AVX
08055A102JAT2A
52
3
10uF 16V 10%
TANT
CT9, CT24–25
SPRAGUE
293D106X9025C2T
A-4
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
ADSP-TS101S EZ-KIT Lite Bill Of Materials
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
53
35
10K 100MW 5%
R8–10, R13, R15,
R30, R32, R36,
R45–47, R52, R53,
R56, R58–59, R61,
R63, R64, R67,
R73–81, R83, R93,
R97, R99, R151,
R152
AVX
CR21-103J-T
54
12
33 100MW 5%
R22, R66, R68–71,
R98, R130, R135,
R138–140
AVX
CR21-330JTR
55
5
4.7K 100MW 5%
R28–29, R31, R35,
R20
AVX
CR21-4701F-T
56
1
1M 100MW 5%
R7
AVX
CR21-1004F-T
57
1
1.5K 100MW 5%
R16
AVX
CR21-1501F-T
58
1
22uF 16V 10%
TANT
CT26
DIG01
PCT3226CT-ND
59
1
2.00K 1/8W 1%
R2
DALE
CRCW1206-2001FRT1
60
2
49.9K 1/8W 1%
R102, R128
AVX
CR32-4992F-T
61
2
2.21K 1/8W 1%
R4–5
AVX
CR32-2211F-T
62
11
100pF 100V 5%
NPO
C11, C18,
C22–23, C27,
C31, C34–35,
C40, C166, C169
AVX
12061A101JAT2A
63
3
10uF 16V 10%
TANT
CT15–17
AVX
TAJB106K016R
64
6
100 100MW 5%
R33, R44, R57,
R60, R62, R65
AVX
CR21-101J-T
65
2
220pf 50V 10%
NPO
C24, C29
AVX
12061A221JAT2A
66
4
1000 100MHZ 1.5A
0.06 CHOKE
L1–L4
MURATA
PLM250S40T1
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
A-5
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
67
3
SILICON
RECTIFIER
D1–D3
GENERALSEMI
S2A
68
3
600 100MHZ
500MA 0.70 BEAD
FER1–3
DIGIKEY
240-1019-1-ND
69
4
237 1/8W 1%
R114, R116, R118,
R121
KOA
P11.0FCT-ND
70
2
750K 1/8W 1%
R115, R117
KOA
RK73H2BT7503F
71
8
5.76K 1/8W 1%
R103, R119–120,
R122–126
DALE
CRCW12065761FRT1
72
2
3.01K 1/8W 1%
R82, R85
KOA
RK73H2BT3011F
73
2
11.0K 1/8W 1%
R101, R129
DALE
CRCW12061102FTR1
74
4
120PF 50V 5%
C36–39
PHILLIPS
1206CG121J9B200
75
4
1UF 16V 10%
C2–3, C15, C163
MURATA
GRM40X7R105K
016AL
76
1
1.0K 1/8W 1%
R89
AVX
CR32-1001F-T
77
2
30PF 100V 5%
C7–8
AVX
12061A300JAT2A
78
4
10 100MW 5%
R25, R72, R149,
R150
DALE
CRCW0805-10R0FRT1
79
2
680PF 50V 1%
NPO
C21, C25
AVX
08055A681FAT2A
80
2
2.74K 1/8W 1%
R108, R113
PANASONIC
ERJ-8ENF2741V
81
4
5.49K 1/8W 1%
R104–105,
R109–110
PANASONIC
ERJ-8ENF5491V
82
2
3.32K 1/8W 1%
R106, R111
PANASONIC
ERJ-8ENF3321V
83
3
1.65K 1/8W 1%
R1, R107, R112
PANASONIC
ERJ-8ENF1651V
84
2
10UF 16V 20%
ELEC
CT11–12
DIG01
PCE3062TR-ND
85
2
68UF 25V 20%
ELEC
CT13, CT18
PANASONIC
EEV-FC1E680P
A-6
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
ADSP-TS101S EZ-KIT Lite Bill Of Materials
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
86
1
1800UF 10V 20%
CT19
RUBYCON
10MBZ1800M
87
1
2.2UH X 20%
L5
COOPER ELE
TEHC
UP2C-2R2
88
2
1800UF 6.3V 20%
CT20–21
RUBYCON
6.3MBZ1800M
89
4
10K 31MW 5%
RN2, RN4, RN5,
RN7
CTS
746X101103J
90
1
3.9NF 50V 5%
C14
PANASONIC
ECH-U1C392JB5
91
1
3.6K 1/8W 1%
R86
PHYCOMP
311-3.60KFTR-ND
92
1
26.7K 1/8W 1%
R92
PHYCOMP
311-26.7KFTR-ND
93
1
.008 1W 5%
R90
PANASONIC
P8.0TTR-ND
94
1
12.1K 1/8W 1%
R91
PHYCOMP
311-12.1KFTR-ND
95
3
10K 50MW 5%
RN1, RN3, RN6
CTS
RT130B7
96
4
0.00 100MW 5%
R144, R147, R148,
R153
PAN
ERJ-6GE10R00V
97
4
10UH X 10%
L1–L4
PANASONIC
ELJ-FC100KF
98
2
3.32K 100MW 1%
R11, R12
DIG01
P3.32KCCTR-ND
99
3
1K 1/8W 5%
R14, R21, R24
AVX
CR32-102J-T
100
1
10K 1/8W 5%
R17
DALE
CRCW1206-1002FRT1
101
3
100K 1/8W 5%
R94, R96, R136
AVX
CR1206-1003FTR1
102
1
20.0K 1/8W 1%
R84
DALE
CRCW1206-2002FRT1
103
2
220 1/8W 5%
R87–88
AVX
CR32-221J-T
104
2
22 1/8W 5%
R3, R6
AVX
CR32-220J-T
105
8
270 1/8W 5%
R18, R37–40,
R42–43, R48
AVX
CR32-271J-T
106
1
680 1/8W 5%
R41
AVX
CR32-681J-T
107
3
RED-SMT
GULL-WING
LED2, LED8,
LED9
PANASONIC
LN1261C
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
A-7
Ref.
Qty.
Description
Reference
Designator
Manufacturer
Part Number
108
1
GREEN-SMT
GULL-WING
LED3
PANASONIC
LN1361C
109
2
604 1/8W 1%
R100, R127
PANASONIC
ERJ-8ENF6040V
110
10
1uF 25V 20%
CT1–8, CT22–23
PANASONIC
ECS-T1EY105R
111
2
QUICKSWITCH-257
U17–18
ANALOG
DEVICES
ADG774ABRQ
112
1
IDC 7X2
P5
BERG
54102-T08-07
113
2
3.5MM
STEREO_JACK
P2–3
SHOGYO
SJ-0359AM-5
114
1
32MB SDRAM
U3
VIKING
PE464U4-CL2
A-8
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
A
B
C
D
1
1
2
2
ADSP-TS101 EZ-KIT LITE
3
3
ANALOG
DEVICES
4
Approvals
Date
Title
Engineering
A
B
C
Size
Board No.
C
Date
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-TS101 EZ-KIT LITE
Drawn
Checked
20 Cotton Road
Rev
A0163-2001
1.4
Sheet
1-19-2004_15:25
D
1
of
12
A
B
C
U1
D
U1
A[0:31]
3.3V
D[0:63]
A0
A1
1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
2
A23
A24
A25
A26
A27
A28
A29
A30
A31
Y15
A0
Y18
A1
AA16
A2
AB17
A3
AB18
A4
AA17
A5
AB19
A6
AB20
A7
AA18
A8
AB21
A9
AA20
A10
Y19
A11
W20
A12
AA21
A13
V20
A14
AA22
A15
Y22
A16
W21
A17
Y21
A18
V21
A19
W22
A20
Y20
A21
U21
A22
T20
A23
V22
A24
T21
A25
U22
A26
T22
A27
R20
A28
R21
A29
U20
A30
P20
A31
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
D19
D20
D21
D22
D23
D24
D25
D26
D27
D28
D29
D30
D31
D32
D33
D34
RD
WRH
WRL
ACK
BMS~/EBOOT
MS0
MS1
L22
RD
L21
WRH
K22
WRL
Y13
ACK
E21
BMS~/EBOOT
M21
MS0
M22
MS1
D35
D36
D37
D38
D39
D40
D41
D42
3
SDCKE
SDA10
SDWE
CAS
RAS
HDQM
LDQM
MSSD
D43
P22
SDCKE
AA19
SDA10
N20
SDWE
R22
CAS
P21
RAS
M20
HDQM
N22
LDQM
N21
MSSD
D44
D45
D46
D47
D48
D49
D50
D51
D52
D53
MSH
BM~/IRQEN
BOFF
BUSLOCK
BRST
HBR
HBG
CPA
DPA
J22
MSH
E20
BM~/IRQEN
AB16
BOFF
G21
BUSLOCK
L20
BRST
AA14
HBR
Y17
HBG
Y14
CPA
AA15
DPA
D54
D55
D56
D57
D58
D59
D60
D61
D62
D63
4
C8
D0
A6
D1
B7
D2
C7
D3
A5
D4
B6
C6
B5
A4
C4
C5
A3
B3
FLAG3_A
IRQ1
D21
IRQ2_A
IRQ2
C21
IRQ3_A
IRQ3
D9
D10
F22
TMR0E~/TM2
TMR0E_A~/TM2
B11
L0DAT0
A11
L0DAT1
C11
L0DAT2
A10
L0DAT3
B10
L0DAT4
C10
L0DAT5
A9
L0DAT6
B9
L0DAT7
A8
L0CLKIN
C9
L0CLKOUT
A7
L0DIR
L0DAT[0:7]_A
L0DAT0_A
L0DAT1_A
1
L0DAT2_A
RN3
L0DAT3_A
B2
L0DAT4_A
IOEN
L0DAT5_A
D12
C20
TCK
D2
D19
E3
D20
B1
D21
E2
D22
C1
D23
D1
D24
E1
D25
F3
D26
G3
D27
G2
D28
F1
D29
F2
D30
H3
D31
R2
D32
R3
D33
V1
D34
V3
D35
T2
D36
T3
D37
U2
D38
U3
D39
W1
D40
V2
D41
Y1
D42
W2
D43
AA1
D44
Y2
D45
W3
D46
AA3
D47
Y4
D48
AA4
D49
AA2
D50
AA5
D51
Y5
D52
AB2
D53
AA6
D54
AB3
D55
DMAR0
D56
DMAR1
TMS
D20
TDO_A
D18
EMU
B20
TMS
D17
TRST
A21
EMU_A
D16
TDI
C18
TRST
D15
TCK
B21
TDI
TDO
AB12
BR0
BR0
AB13
BR1
BR1
AA12
BR2
BR2
AB14
BR3
BR3
Y12
BR4
A2
L0DAT6_A
ACK
L0DAT7_A
MS1
L0CLKIN_A
CPA
L0CLKOUT_A
A3
B1
B3
C1
RESET
C2
BR5
AA13
BR6
BR6
Y16
BR7
BR7
J20
ID0_A
ID0
H22
ID1_A
ID1
J21
ID2_A
ID2
B17
CONTROLIMP0
A18
CONTROLIMP1
A17
CONTROLIMP2
C15
DS0
B16
DS1
C16
DS2
A13
VREF
CONTROLIMP0
CONTROLIMP1
CONTROLIMP2
DS0
DS1
DS2
LCLK_N
C12
LCLK_P_A
LCLK_P
F20
LCLKRAT0
D22
LCLKRAT1
E22
LCLKRAT2
LCLKRAT0
LCLKRAT1
LCLKRAT2
A15
VREF
M1
L1DAT0
M3
L1DAT1
M2
L1DAT2
N1
L1DAT3
P1
L1DAT4
N2
L1DAT5
R1
L1DAT6
N3
L1DAT7
P3
L1CLKIN
P2
L1CLKOUT
T1
L1DIR
L1DAT0_A
AA9
L2DAT0
AB7
L2DAT1
AB8
L2DAT2
AA10
L2DAT3
Y9
L2DAT4
Y3
L2DAT5
AB9
L2DAT6
AA11
L2DAT7
AB10
L2CLKIN
Y10
L2CLKOUT
AB11
TM1/L2DIR
L2DAT0
H2
L3DAT0
G1
L3DAT1
H1
L3DAT2
J2
L3DAT3
J3
L3DAT4
J1
L3DAT5
K3
L3DAT6
K2
L3DAT7
L1
L3CLKIN
K1
L3CLKOUT
L3
L3DIR
L3DAT0
L1DAT[0:7]_A
BR2
C3
E2
L1DAT1_A
D1
L1DAT2_A
D2
L1DAT3_A
BR6
L1DAT4_A
D3
E1
L1DAT5_A
BR3
L1DAT6_A
L1DAT7_A
L1CLKIN_A
HBR
L1CLKOUT_A
COM1
R1
R2
R3
R4
R5
R6
R7
R8
COM2
R9
R10
R11
R12
E3
R13
F1
R14
F2
R15
F3
R16
10K
BGA36
L2
COM4
K1
R32
K2
R31
K3
R30
L1
R29
L3
R28
M1
R27
M2
R26
M3
R25
H2
COM3
G1
R24
G2
R23
G3
R22
H1
R21
H3
R20
J1
R19
J2
R18
J3
R17
HBG
BRST
DMAR2
MSH
DMAR0
FLYBY
BUSLOCK
DMAR1
DPA
BR5
BR7
BOFF
BR4
DMAR3
2
BR4
AB15
BR5
SCLK_N
L2DAT[0:7]
L2DAT1
L2DAT2
L2DAT3
3.3V
L2DAT4
L2DAT5
L2DAT6
L2DAT7
L2CLKOUT_B
R56
10K
805
L2CLKOUT_A
TM1/L2DIR
R53
10K
805
R63
10K
805
R76
10K
805
L3DAT[0:7]
RD
L3DAT1
WRH
L3DAT2
WRL
L3DAT3
MS0
L3DAT4
L3DAT5
L3DAT6
3
L3DAT7
L3CLKOUT_B
3.3V
L3CLKOUT_A
A16
SCLK_P_A
SCLK_P
F21
SCLKFREQ
SCLKFREQ
R2
2.00K
1206
VREF
A19
DSP_RESET
K21
FLYBY
K20
IOEN
B19
A20
B18
D57
DMAR2
Y6
D58
DMAR3
AB5
D59
Y7
D60
AA8
D61
B13
AB6
D62
A14
Y8
D63
VDDINT
L2
10UH
1008
L1
10UH
1008
ADSP-TS101SKB2180
PBGA484
C19
C17
VREF
C14
CT6
1UF
A
C5
0.001UF
805
B14
RESET
R1
1.65K
1206
FLYBY
C4
0.001UF
805
DMAR0
DMAR1
DMAR2
DMAR3
VREF
AVDD1
ANALOG
DEVICES
AVDD2
AGND1
AGND2
ADSP-TS101SKB2180
PBGA484
Approvals
Checked
Engineering
B
C3
1UF
805
IOEN
Date
Title
Drawn
A
A1
D11
B2
AA7
IRQ0
B22
IRQ1_A
D8
D14
AB4
C22
IRQ0_A
D7
A2
C2
FLAG2_A
D6
D13
D3
FLAG1_A
D5
B4
C3
G22
FLAG0
H20
FLAG1
H21
FLAG2
G20
FLAG3
FLAG0_A
C
Size
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-TS101 EZ-KIT LITE - DSP A
Board No.
C
Date
20 Cotton Road
Rev
A0163-2001
1.4
Sheet
1-19-2004_15:28
D
2
of
12
A
B
C
U2
D
U2
A[0:31]
D[0:63]
A0
A1
1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
2
A23
A24
A25
A26
A27
A28
A29
A30
A31
Y15
A0
Y18
A1
AA16
A2
AB17
A3
AB18
A4
AA17
A5
AB19
A6
AB20
A7
AA18
A8
AB21
A9
AA20
A10
Y19
A11
W20
A12
AA21
A13
V20
A14
AA22
A15
Y22
A16
W21
A17
Y21
A18
V21
A19
W22
A20
Y20
A21
U21
A22
T20
A23
V22
A24
T21
A25
U22
A26
T22
A27
R20
A28
R21
A29
U20
A30
P20
A31
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
D19
D20
D21
D22
D23
D24
D25
D26
D27
D28
D29
D30
D31
D32
D33
D34
RD
WRH
WRL
ACK
BMS~/EBOOT
MS0
MS1
L22
RD
L21
WRH
K22
WRL
Y13
ACK
E21
BMS~/EBOOT
M21
MS0
M22
MS1
D35
D36
D37
D38
D39
D40
D41
D42
3
SDCKE
SDA10
SDWE
CAS
RAS
HDQM
LDQM
MSSD
D43
P22
SDCKE
AA19
SDA10
N20
SDWE
R22
CAS
P21
RAS
M20
HDQM
N22
LDQM
N21
MSSD
D44
D45
D46
D47
D48
D49
D50
D51
D52
D53
MSH
BM~/IRQEN
BOFF
BUSLOCK
BRST
HBR
HBG
CPA
DPA
J22
MSH
E20
BM~/IRQEN
AB16
BOFF
G21
BUSLOCK
L20
BRST
AA14
HBR
Y17
HBG
Y14
CPA
AA15
DPA
D54
D55
D56
D57
D58
D59
D60
D61
D62
D63
4
C8
D0
A6
D1
B7
D2
C7
D3
A5
D4
B6
D5
C6
D6
B5
D7
A4
D8
C4
D9
C5
D10
A3
D11
B3
D12
B4
D13
A2
D14
C3
D15
D3
D16
C2
D17
B2
D18
D2
D19
E3
D20
B1
D21
E2
D22
C1
D23
D1
D24
E1
D25
F3
D26
G3
D27
G2
D28
F1
D29
F2
D30
H3
D31
R2
D32
R3
D33
V1
D34
V3
D35
T2
D36
T3
D37
U2
D38
U3
D39
W1
D40
V2
D41
Y1
D42
W2
D43
AA1
D44
Y2
D45
W3
D46
AA3
D47
Y4
D48
AA4
D49
AA2
D50
AA5
D51
Y5
D52
AB2
D53
AA6
D54
AB3
D55
DMAR0
D56
DMAR1
AB4
G22
FLAG0
H20
FLAG1
H21
FLAG2
G20
FLAG3
FLAG0_B
FLAG1_B
FLAG2_B
FLAG3_B
C22
IRQ0_B
B22
IRQ1_B
IRQ2_B
C20
TCK
TDI
C18
TRST
TRST
A21
EMU_B
EMU
B20
TMS
TMS
D20
TDO_B
TDO
AB12
BR0
BR0
AB13
BR1
BR1
AA12
BR2
BR2
AB14
BR3
BR3
Y12
BR4
BR5
AA13
BR6
BR6
Y16
BR7
BR7
J20
ID0_B
ID0
H22
ID1_B
ID1
J21
ID2_B
ID2
B17
CONTROLIMP0
A18
CONTROLIMP1
A17
CONTROLIMP2
C15
DS0
B16
DS1
C16
DS2
A13
VREF
CONTROLIMP0
CONTROLIMP1
CONTROLIMP2
DS0
DS1
DS2
LCLK_N
C12
LCLK_P_B
LCLK_P
F20
LCLKRAT0
D22
LCLKRAT1
E22
LCLKRAT2
LCLKRAT0
LCLKRAT1
LCLKRAT2
A15
VREF
L0DAT0_B
M1
L1DAT0
M3
L1DAT1
M2
L1DAT2
N1
L1DAT3
P1
L1DAT4
N2
L1DAT5
R1
L1DAT6
N3
L1DAT7
P3
L1CLKIN
P2
L1CLKOUT
T1
L1DIR
L1DAT0_B
AA9
L2DAT0
AB7
L2DAT1
AB8
L2DAT2
AA10
L2DAT3
Y9
L2DAT4
Y3
L2DAT5
AB9
L2DAT6
AA11
L2DAT7
AB10
L2CLKIN
Y10
L2CLKOUT
AB11
TM1/L2DIR
L2DAT0
H2
L3DAT0
G1
L3DAT1
H1
L3DAT2
J2
L3DAT3
J3
L3DAT4
J1
L3DAT5
K3
L3DAT6
K2
L3DAT7
L1
L3CLKIN
K1
L3CLKOUT
L3
L3DIR
L3DAT0
L0DAT[0:7]_B
L0DAT1_B
1
L0DAT2_B
L0DAT3_B
L0DAT4_B
L0DAT5_B
L0DAT6_B
L0DAT7_B
L0CLKIN_B
L0CLKOUT_B
L1DAT[0:7]_B
L1DAT1_B
L1DAT2_B
L1DAT3_B
L1DAT4_B
L1DAT5_B
L1DAT6_B
L1DAT7_B
L1CLKIN_B
L1CLKOUT_B
2
BR4
AB15
BR5
SCLK_N
L2DAT[0:7]
L2DAT1
L2DAT2
L2DAT3
L2DAT4
L2DAT5
L2DAT6
L2DAT7
L2CLKOUT_A
L2CLKOUT_B
TM1/L2DIR
L3DAT[0:7]
L3DAT1
L3DAT2
L3DAT3
L3DAT4
L3DAT5
VREF
L3DAT6
3
L3DAT7
C163
1UF
805
L3CLKOUT_A
L3CLKOUT_B
SCLK_P_B
SCLK_P
F21
SCLKFREQ
A19
DSP_RESET
K21
FLYBY
K20
IOEN
B19
A20
B18
DMAR2
Y6
D58
DMAR3
AB5
D59
Y7
D60
AA8
D61
B13
AB6
D62
A14
Y8
D63
C19
C17
VREF
C14
CT7
1UF
A
C6
0.001UF
805
B14
RESET
FLYBY
IOEN
DMAR0
DMAR1
DMAR2
DMAR3
VREF
AVDD1
ANALOG
DEVICES
AVDD2
AGND1
AGND2
ADSP-TS101SKB2180
PBGA484
Approvals
Date
Title
Drawn
Checked
Engineering
A
B
C164
0.001UF
805
A16
SCLKFREQ
ADSP-TS101SKB2180
PBGA484
TCK
B21
TDI_B
L3
10UH
1008
IRQ3
F22
TMR0E~/TM2
TMR0E_B~/TM2
L4
10UH
1008
IRQ2
C21
IRQ3_B
VDDINT
IRQ1
D21
D57
AA7
IRQ0
B11
L0DAT0
A11
L0DAT1
C11
L0DAT2
A10
L0DAT3
B10
L0DAT4
C10
L0DAT5
A9
L0DAT6
B9
L0DAT7
A8
L0CLKIN
C9
L0CLKOUT
A7
L0DIR
C
Size
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-TS101 EZ-KIT LITE - DSP B
Board No.
C
Date
20 Cotton Road
Rev
A0163-2001
1.4
Sheet
1-19-2004_15:28
D
3
of
12
A
B
C
4M x 64 SDRAM
D
3.3V
U3
A[0:15]
D[0:63]
A1
A2
A3
1
A4
A5
A6
A7
A8
A9
A10
SDA10
A12
A13
A14
33
A0
117
A1
34
A2
118
A3
35
A4
119
A5
36
A6
120
A7
37
A8
121
A9
38
A10
123
A11
126
A12
122
BA0
39
BA1
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
28
LDQM
29
46
DQMB0
DQMB1
D17
DQMB2
D18
47
DQMB3
112
DQMB4
113
DQMB5
130
DQMB6
131
DQMB7
HDQM
2
D16
D19
D20
D21
D22
D23
D24
27
SDWE
WE
128
CKE0
111
CAS
115
RAS
30
S0
45
S2
SDCKE
CAS
RAS
MSSD
D25
D26
D27
D28
D29
D30
D31
42
SDRAM_CLK0
CK0
125
CK1
79
CK2
163
CK3
SDRAM_CLK1
SDRAM_CLK2
SDRAM_CLK3
D32
D33
D34
D35
D36
83
81
SCL
D37
WP
D38
82
SDA
165
SA0
166
SA1
167
SA2
D39
D40
D41
D42
D43
3
D44
D45
D46
D47
D48
D49
D50
D51
D52
D53
D54
D55
D56
D57
D58
D59
D60
D61
D62
D63
4
2
D0
3
D1
4
D2
5
D3
7
D4
PA0
8
D5
PA1
9
D6
PA2
D7
PA3
RN1
10
D8
PA4
13
D9
PA5
14
D10
PA6
11
15
D11
16
D12
17
D13
PA7
PB0
19
D14
PB1
20
D15
PB2
55
56
57
58
60
65
66
D16
PB3
D17
PB4
D18
PB5
D19
PB6
PB7
D20
D21
B2
COM1
A1
R1
A2
R2
A3
R3
B1
R4
B3
R5
C1
R6
C2
R7
C3
R8
E2
COM2
D1
R9
D2
R10
D3
R11
E1
R12
E3
R13
F1
R14
F2
R15
F3
R16
10K
BGA36
L2
COM4
K1
R32
K2
R31
K3
R30
L1
R29
L3
R28
M1
R27
M2
R26
M3
R25
H2
COM3
G1
R24
G2
R23
G3
R22
H1
R21
H3
R20
J1
R19
J2
R18
J3
R17
PG0
PG1
PG2
PG3
PG4
PG5
PG6
PG7
PC6
PC7
PD0
PD1
PD2
PD3
PE6
PE7
D23
69
D24
70
D25
RN5
1
71
D26
2
72
D27
3
74
D28
4
75
D29
6
76
D30
7
77
D31
8
86
D32
9
87
D33
88
D34
89
D35
91
92
A0
3
A1
4
A2
5
A3
6
A4
7
A5
10
A6
11
A7
12
A8
13
A9
14
A10
15
A11
16
A12
17
A13
18
A14
19
A15
20
3.3V
R1
R2
5
COM1
10
COM2
R3
R4
R5
R6
PC6
R7
PC7
A16
41
A17
42
A18
43
A19
44
A20
45
A21
46
47
48
10K
RNET8
RD
BMS~/EBOOT
D36
59
60
40
D38
D39
D40
74
97
D41
75
98
99
100
D42
3.3V
P1
1
D43
D44
3
76
2
PE6
4
101
D45
5
6
103
D46
7
8
PE7
U6
1
1
AD2
PF2
AD3
PF3
AD4
PF4
AD5
PF5
AD6
PF6
AD7
PF7
D47
9
10
139
D48
11
12
140
D49
13
14
141
D50
142
D51
144
D52
149
D53
150
D54
151
D55
153
D56
154
D57
155
D58
156
D59
158
D60
159
D61
160
D62
161
D63
RESET
2
77
78
39
2
SN74AHC1G00
SOT23-5
SN74AHC1G00
SOT23-5
D0
32
D1
33
D2
34
D3
35
D4
36
D5
37
D6
38
D7
21
PG0
22
PG1
23
PG2
24
PG3
25
PG4
26
PG5
27
PG6
28
PG7
AD9
AD10
AD11
AD12
AD13
AD14
AD15
PG0
PG1
PG2
PG3
PG4
PG5
PG6
2
PG7
PC0
PC1
PA0
PC2
PA1
PC3
PA2
PC4
PA3
PC5
PA4
PC6
PA5
PC7
PA6
51
PA0
52
PA1
53
PA2
54
PA3
55
PA4
56
PA5
57
PA6
58
PA7
CNTL0/~WR
CNTL1/~RD
PB0
CNTL2
PB1
PE0/TMS
PB3
PE1/TCK
PB4
PE2/TDI
PB5
PE3/TDO
PB6
PE4/TSTAT
PB7
61
PB0
62
PB1
63
PB2
64
PB3
65
PB4
66
PB5
67
PB6
68
PB7
PE5/~TERR
PE6
PD0
PE7
PD1
PD2
4
31
AD8
U5
4
104
PF1
D37
73
95
PF0
AD1
PB2
72
94
AD0
PA7
WRL
71
93
D[7:0]
R8
RESET
PD3
79
3
PD0
80
PD1
1
PD2
2
PD3
DSM2150F5V-12T6
TQFP80
IDC7X2SRDRA
7X2
C1
0.1UF
805
C2
1UF
805
DSM JTAG HEADER
ANALOG
DEVICES
MT4LSDT464A
DIMM168
Approvals
Date
Title
Drawn
Checked
Engineering
A
U4
A[21:0]
D22
67
1
512 KB MAIN FLASH
32KB SECONDARY FLASH
B
C
Size
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-TS101 EZ-KIT LITE - SDRAM & FLASH
Board No.
C
Date
20 Cotton Road
Rev
A0163-2001
1.4
Sheet
1-19-2004_15:28
D
4
of
12
A
B
C
D
1
1
3.3V
3.3V
R93
10K
805
DAC
U8
10
R97
10K
805
ADC
C166
100PF
1206
2
C10
0.01UF
805
R10
10K
805
MCLK
U7
13
CAPLN
BCLK
21
CASC
LRCLK
12
CAPLP
C165
0.01UF
805
INL+
INL-
INR+
INR-
11
VINLP
10
VINLN
18
VINRP
19
CAPRN
17
CAPRP
C169
100PF
1206
MCLK
C168
0.01UF
805
RESET
DT
8
XCTRL
2
CCLK/{256~/512}
3
COUT/{DF0}
4
CIN/{DF1}
5
CLATCH/{M~/S}
4
CCLK
3
CLATCH
5
CDATA
16
OUTL-
OUTL-
17
OUTL+
OUTL+
13
OUTR12
OUTR+
OUTROUTR+
2
14
FILTR
19
FILTB
ZEROL
22
8
ZEROR
VINRN
16
C167
0.01UF
805
96/48~
6
384/256~
7
X2MCLK
2
MCLK
26
BCLK
25
LRCLK
27
SDATA
1
MCLK
24
RESET
28
LRCLK
27
BCLK
26
DOUT
25
DIN
VREF
LRCLK
24
RESET
RESET
CT15
10UF
B
BCLK
9
DEEMP
DR
23
14
VREF_AUDIO
21
AD1871
SSOP28
20
C17
0.1UF
805
CT17
10UF
B
C16
0.1UF
1206
CT16
10UF
B
MUTE
IDPM0
IDPM1
AD1854
SSOP28
AGND
AGND
3
3
SLAVE MODE
MCLK IS 256 x Fs
48 kHZ SAMPLE RATE
2
I S I/F MODE
3.3V
R99
10K
805
R98
33
805
U9
1
OE
3
OUT
AUDIOCLK
ANALOG
DEVICES
12.288MHZ
OSC003
4
Approvals
Date
Title
Drawn
Checked
Engineering
A
B
C
Size
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-TS101 EZ-KIT LITE - AUDIO INTERFACE
Board No.
C
Date
20 Cotton Road
Rev
A0163-2001
1.4
Sheet
1-19-2004_15:28
D
5
of
12
A
B
C
D
1
1
CT11
10UF
CAP002
FER2
600
1206
R94
100K
1206
R119
5.76K
1206
R120
5.76K
1206
C36
120PF
1206
C34
100PF
1206
2
R121
237
1206
U10
1
INL-
AGND
3
VREF_AUDIO
SSM2275S
SOIC8
R124
5.76K
1206
R123
5.76K
1206
P2
C31
100PF
1206
ADC LEFT
C37
120PF
1206
1
2
C33
0.001UF
805
5
AGND
4
R117
750K
1206
LOOPBACK_LEFT
3
6
LOOPBACK_RIGHT
R118
237
1206
U10
2
2
C30
0.001UF
805
7
CON001
STEREO_JACK
INL+
5
SSM2275S
SOIC8
AGND
CT12
10UF
CAP002
FER3
600
1206
R122
5.76K
1206
R103
5.76K
1206
AGND
R96
100K
1206
C38
120PF
1206
C35
100PF
1206
6
R116
237
1206
U11
7
INR-
AGND
5
SSM2275S
SOIC8
3
R126
5.76K
1206
C32
0.001UF
805
R125
5.76K
1206
3
C23
100PF
1206
ADC RIGHT
C39
120PF
1206
AGND
R115
750K
1206
2
C28
0.001UF
805
R114
237
1206
U11
1
INR+
3
SSM2275S
SOIC8
AGND
ANALOG
DEVICES
4
Approvals
Drawn
Checked
Engineering
A
B
C
Date
20 Cotton Road
Nashua, NH 03063
4
PH: 1-800-ANALOGD
Title
ADSP-TS101 EZ-KIT LITE - AUDIO IN AMPLIFIERS
Size
Board No.
C
Date
Rev
A0163-2001
1.4
Sheet
1-19-2004_15:28
D
6
of
12
A
B
C
D
1
1
R105
5.49K
1206
R101
11.0K
1206
C22
100PF
1206
R106
3.32K
1206
OUTR-
C20
330PF
805
DAC RIGHT
2
CT13
68UF
CAP003
U12
C18
100PF
1206
R100
604
1206
1
3
R104
5.49K
1206
C21
680PF
805
SSM2275S
SOIC8
R107
1.65K
1206
C19
2200PF
1206
R102
49.9K
1206
OUTR+
R108
2.74K
1206
2
C24
220PF
1206
2
AGND
P3
2
VREF_AUDIO
3
LOOPBACK_RIGHT
4
LOOPBACK_LEFT
AGND
5
1
CON001
STEREO_JACK
R110
5.49K
1206
R129
11.0K
1206
C27
100PF
1206
R111
3.32K
1206
OUTL-
C26
330PF
805
DAC LEFT
6
CT18
68UF
CAP003
U12
C40
100PF
1206
R127
604
1206
7
5
R109
5.49K
1206
3
C25
680PF
805
SSM2275S
SOIC8
R112
1.65K
1206
C41
2200PF
1206
R128
49.9K
1206
3
OUTL+
R113
2.74K
1206
C29
220PF
1206
AGND
AGND
ANALOG
DEVICES
4
Approvals
Drawn
Checked
Engineering
A
B
C
Date
20 Cotton Road
Nashua, NH 03063
4
PH: 1-800-ANALOGD
Title
ADSP-TS101 EZ-KIT LITE - AUDIO OUT AMPLIFIERS
Size
Board No.
C
Date
Rev
A0163-2001
1.4
Sheet
1-19-2004_15:28
D
7
of
12
A
B
C
D
3.3V
R58
10K
805
R57
100
805
U24
1
R49
0.00
1206
U35
1
2
4
1
SW3
SWT013
SPST-MOMENTARY
74LVC14A
SOIC14
3.3V
IRQ0_A
2
SN74AHC1G00
SOT23-5
1
CT1
1UF
A
R36
10K
805
3.3V
USB_CONFIGURED
3.3V
R46
10K
805
U25
1
U26
4
1
MR
4
PFI
SW1
SWT013
SPST-MOMENTARY
R59
10K
805
R44
100
805
U24
4
4
74LVC14A
SOIC14
8
USB_RESET
2
SN74AHC1G00
SOT23-5
7
5
RESET
ADM708SAR
SOIC8
3.3V
IRQ0_B
2
SW6
SWT013
SPST-MOMENTARY
RESET
PFO
R50
0.00
1206
U36
1
3
RESET
SN74AHC1G00
SOT23-5
SOFT_RESET
CT2
1UF
A
2
2
USB RESET
LED2
RED-SMT
LED001
R43
270
1206
RESET
LED8
RED-SMT
LED001
DSP_RESET
LED9
RED-SMT
LED001
R48
270
1206
R42
270
1206
3.3V
3.3V
U27
USB_RESET
RESET
DSP_RESET
R47
10K
805
R32
10K
805
R62
100
805
R55
0.00
1206
U24
5
SW4
SWT013
SPST-MOMENTARY
6
FLAG0_A
74LVC14A
SOIC14
11
FLAG2_A
R34
0.00
1206
U24
SW9
SWT013
SPST-MOMENTARY
CT4
1UF
A
3
R33
100
805
10
FLAG2_B
FLAG1_A
74LVC14A
SOIC14
FLAG3_A
FLAG3_B
CT8
1UF
A
2
1A1
4
1A2
6
1A3
8
1A4
1Y1
1Y2
1Y3
1Y4
11
2A1
13
2A2
15
2A3
17
2A4
2Y1
2Y2
2Y3
2Y4
18
16
14
5V
12
9
7
5
3
3
1
OE1
19
OE2
FLAG3_B
LED5
AMBER-SMT
LED001
FLAG3_A/AUDIO
LED6
AMBER-SMT
LED001
FLAG2_B
LED4
AMBER-SMT
LED001
FLAG2_A
LED7
AMBER-SMT
LED001
POWER
LED3
GREEN-SMT
LED001
IDT74FCT3244APY
SSOP20
R37
270
1206
R38
270
1206
R39
270
1206
R40
270
1206
R41
680
1206
3.3V
3.3V
R64
10K
805
R61
10K
805
R60
100
805
U24
9
SW5
SWT013
SPST-MOMENTARY
8
74LVC14A
SOIC14
R65
100
805
R51
0.00
1206
13
FLAG0_B
SW2
SWT013
SPST-MOMENTARY
12
FLAG1_B
ANALOG
DEVICES
74LVC14A
SOIC14
CT5
1UF
A
CT3
1UF
A
4
R54
0.00
1206
U24
Approvals
Drawn
Checked
Engineering
A
B
C
Date
20 Cotton Road
Nashua, NH 03063
4
PH: 1-800-ANALOGD
Title
ADSP-TS101 EZ-KIT LITE - PUSH BUTTONS & LEDS
Size
Board No.
C
Date
Rev
A0163-2001
1.4
Sheet
1-19-2004_15:28
D
8
of
12
A
B
C
D
DSP_A ID = 000
1
1
ID0_A
ID1_A
3.3V
ID2_A
R83
10K
805
R45
10K
805
R52
10K
805
RN2
1
R1
2
R2
3
R3
4
R4
6
R5
7
R6
8
R7
9
R8
3.3V
COM1
COM2
5
10
ID2_B
10K
RNET8
ID1_B
RN4
R75
10K
805
R74
10K
805
R73
10K
805
1
R1
2
R2
3
R3
4
R4
6
R5
7
R6
8
R7
9
R8
2
ID0_B
DSP_B ID = 001
1
23
3
22
4
21
5
20
6
19
7
18
8
17
9
16
10
15
11
14
12
13
3
CONTROLIMP2
4
DS0
SCLK_P_A
DS2
R70
33
805
3
1
IN
O5
O6
O7
O8
O9
O10
LCLKRAT2
LCLK_P_B
7
9
14
3
R153
DNP
805
DEFAULT SETTINGS
CLKOUT
R25
10
805
CONTROLIMP0 ON
CONTROLIMP1 OFF
CONTROLIMP2 OFF
SDRAM_CLK1
R149
10
805
SDRAM_CLK2
R150
10
805
SDRAM_CLK3
DS0
OFF
DS1
OFF
DS2
OFF
BMS~
ON
BM~
ON
LCLKRAT0
ON
LCLKRAT1
OFF
LCLKRAT2
ON
ANALOG
DEVICES
4
Approvals
Date
Title
Drawn
Checked
Engineering
A
R24
1K
1206
SDRAM_CLK0
R130
33
805
19
IDT74FCT3807AQ
QSOP20
R21
1K
1206
SWT014
DIP12
16
18
SCLKFREQ
R72
10
805
11
12
12
OUT
O4
5
LCLKRAT1
R71
33
805
11
83.33MHZ
OSC003
O3
3
10
1
OE
9
LCLKRAT0
LCLK_P_A
O2
R66
33
805
8
BM~/IRQEN
U29
U28
BMS~/EBOOT
7
SCLK_P_B
6
3.3V
5
DS1
R69
33
805
24
2
2
R68
33
805
R67
10K
805
10
2
ON
SW7
1
CONTROLIMP1
3
COM2
5
10K
RNET8
CONTROLIMP0
O1
COM1
B
C
Size
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-TS101 EZ-KIT LITE - CONFIGURATION
Board No.
C
Date
20 Cotton Road
Rev
A0163-2001
1.4
Sheet
1-19-2004_15:28
D
9
of
12
A
B
C
D
P7
26
14
15
1
UD2
UD1
CLKSH
CLK
2
3
ACK
16
4
D0SH
D0
17
5
D1SH
D1
18
6
D2SH
D2
19
7
D3SH
D3
20
8
D4SH
D4
21
9
D5SH
D5
22
10
D6SH
D6
23
11
D7SH
D7
24
12
RXCLKSH RXCLK
25
13
TXCLKSH TXCLK
1
28
ACKSH
CH1
L0DAT0_A
L0DAT[0:7]_A
L0DAT1_A
L0DAT2_A
L0DAT3_A
D[0:63]
L0DAT4_A
A[0:31]
L0DAT5_A
L0DAT6_A
3.3V
L0DAT7_A
L0CLKIN_A
L0CLKOUT_A
27
P13
CH2
P11
LINKPORT
CON010
A1
P8
26
14
15
A3
1
UD2
UD1
CLKSH
CLK
28
CH1
L1DAT0_A
L1DAT[0:7]_A
1
4
3
6
5
10
A7
ACKSH
2
8
A5
2
3
ACK
16
4
D0SH
D0
17
5
D1SH
D1
18
6
D2SH
D2
19
7
D3SH
D3
20
8
D4SH
D4
21
9
D5SH
D5
22
10
D6SH
D6
23
11
D7SH
D7
24
12
RXCLKSH RXCLK
25
13
TXCLKSH TXCLK
2
1
5V
12
7
9
11
A2
A4
RAS
A9
14
13
A8
A11
16
15
A10
MSSD
18
17
A12
L1DAT2_A
A15
20
19
A14
L1DAT3_A
A17
22
21
A16
L1DAT4_A
A19
24
23
A18
L1DAT5_A
A21
26
25
A20
28
A25
L1CLKIN_A
L1CLKOUT_A
30
A27
32
27
29
31
34
33
A28
36
35
A30
D1
40
D3
42
D5
44
41
43
FLAG1_A
FLAG3_A
37
39
D0
D2
FLAG1_B
FLAG3_B
D7
14
46
45
UD1
CLKSH
CLK
D9
48
47
D8
D11
50
49
D10
2
3
ACKSH
ACK
16
4
D0SH
D0
17
5
D1SH
D1
18
6
D2SH
D2
19
7
D3SH
D3
20
8
D4SH
D4
21
9
D5SH
D5
22
10
D6SH
D6
23
11
D7SH
D7
24
12
RXCLKSH RXCLK
25
13
TXCLKSH TXCLK
15
L0DAT0_B
L0DAT[0:7]_B
CH1
52
51
D12
D15
54
53
D14
D17
56
55
D16
L0DAT1_B
D19
58
57
D18
D21
60
59
D20
L0DAT3_B
L0DAT4_B
D23
62
61
D22
D25
64
63
D24
D27
66
65
D26
L0DAT5_B
L0DAT6_B
L0DAT7_B
L0CLKIN_B
L0CLKOUT_B
27
CH2
LINKPORT
CON010
68
D31
70
D33
72
14
15
1
UD1
CLKSH
CLK
3
ACK
16
4
D0SH
D0
17
5
D1SH
D1
18
6
D2SH
D2
19
7
D3SH
D3
20
8
D4SH
D4
21
9
D5SH
D5
22
10
D6SH
D6
23
11
D7SH
D7
24
12
RXCLKSH RXCLK
25
13
TXCLKSH TXCLK
28
76
75
D36
IRQ1_B
4
80
82
84
86
ACKSH
CH1
IRQ1_A
D37
D47
L1DAT0_B
D32
D34
78
L1DAT[0:7]_B
L1DAT1_B
77
79
81
83
85
88
87
90
89
PRT_NUM=DNP
45X2
IDC45X2
L1DAT2_B
3
6
5
6
5
8
7
8
7
10
9
10
9
D49
12
11
D48
12
11
D51
14
13
D50
14
13
D53
16
15
D52
16
15
D55
18
17
D54
18
17
D57
20
19
D56
20
19
D59
22
21
D58
22
21
D61
24
23
D60
24
23
D63
26
25
D62
26
25
28
27
28
27
30
29
30
29
32
31
32
31
34
33
34
33
36
35
36
35
38
37
38
37
40
39
40
39
42
41
42
41
44
43
44
43
46
45
46
45
48
47
48
47
50
49
50
49
52
51
52
51
54
53
54
53
56
55
56
55
58
57
58
57
60
59
60
59
62
61
62
61
64
63
64
63
66
65
66
65
68
67
68
67
70
69
70
69
72
71
72
71
74
73
74
73
76
75
76
75
78
77
78
77
80
79
80
79
82
81
82
81
84
83
84
83
86
85
86
85
88
87
88
87
90
89
90
89
SDWE
DMAR1
SDA10
DMAR3
HDQM
LDQM
DSP_RESET
RESET
PA0
PA1
FLAG0_A
PA2
FLAG2_A
PA3
FLAG0_B
PA4
FLAG2_B
PA5
PA6
PA7
DT
TMR0E_A~/TM2
HBG
D30
73
D45
2
71
TMR0E_B~/TM2
74
D43
UD2
69
D28
D35
D39
P10
67
IRQ3_A
D41
26
DR
L0DAT2_B
3
28
D13
D29
4
D6
1
UD2
3
D4
P9
26
4
A26
A31
38
1
A24
A29
CH2
2
A22
27
LINKPORT
CON010
CAS
A6
A13
L1DAT7_A
SDRAM_CLK2
SDCKE
A23
D38
IRQ3_B
IRQ0_A
BMS~/EBOOT
IRQ2_A
MS0
IRQ0_B
MS1
IRQ2_B
FLYBY
IOEN
D40
ACK
D42
MSH
D44
BM~/IRQEN
D46
DMAR0
DMAR2
CLKOUT
2
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
HBR
DPA
CPA
3
RD
WRL
WRH
BOFF
BUSLOCK
BRST
PRT_NUM=DNP
45X2
IDC45X2
PRT_NUM=DNP
45X2
IDC45X2
L1DAT3_B
L1DAT4_B
L1DAT5_B
L1DAT6_B
L1DAT7_B
L1CLKIN_B
ANALOG
DEVICES
L1CLKOUT_B
27
CH2
LINKPORT
CON010
Approvals
Drawn
Checked
SHGND
Engineering
A
1
A0
L1DAT1_A
L1DAT6_A
2
P12
B
C
Date
20 Cotton Road
Nashua, NH 03063
4
PH: 1-800-ANALOGD
Title
ADSP-TS101 EZ-KIT LITE - EXPANSION CONNECTORS
Size
Board No.
C
Date
Rev
A0163-2001
1.4
Sheet
1-19-2004_15:28
D
10
of
12
A
B
C
D
CT19
1800UF
CAP015
U30
PGND
CT9
10UF
C
1
8
V+
6
LV
5
OUT
7
OSC
FC
2
F1
7A
FUS003
1
FER4
CHOKE_COIL
4
3
1
2
CAP+
D1
2A
DO-214AA
4
CAP-
3
GND
P14
CT26
22UF
D
CT10
4.7UF
C
5
ADM660
SOIC8
1
C85
1000PF
1206
2
Q2
FDS6982
SOIC8
4
D2
2A
DO-214AA
3
PGND
R144
0.00
805
3
7_5V_POWER
CON005
PGND
PGND
VDDINT
L5
2.2UH
IND002
R90
.008
2512
U31
1
VID3
2
VID2
3
VID1
4
VID0
5
VID25
8
SD
9
FB
R145
0.00
805
C84
1000PF
1206
1
C9
0.1UF
805
R146
0.00
805
R147
0.00
805
R148
0.00
805
SHGND
16
VCC
18
DRVH
17
DRVL
15
LRFB
14
LRDRV
13
COMP
7
REF
11
CS+
10
CS12
CT
6
PWRGOOD
20
GND
19
PGND
7
CT20
1800UF
CAP015
Q2
FDS6982
SOIC8
2
1
PGND
PGND
D3
2A
DO-214AA
C15
1UF
805
2
Q1
IRFR024
TO252AA
1
2
AGND
CT21
1800UF
CAP015
C13
150PF
1206
ADP3170
TSSOP20
C14
3.9NF
805
R91
12.1K
1206
R92
26.7K
1206
2
3
3.3V
PGND
AGND
5V
VR2
7V_IN
3
INPUT
OUTPUT
GND
1
R136
100K
1206
CT24
10UF
C
PGND
2
CT14
220UF
E
AGND
ADP3339AKC-5
SOT-223
C105
0.1UF
805
CT25
10UF
C
R85
3.01K
1206
R87
220
1206
AGND
C106
0.1UF
805
PGND
C12
0.001UF
805
R88
220
1206
R86
3.6K
1206
PGND
R89
1.0K
1206
2.5V
5V
3
AGND
3
VR1
3
INPUT
2
OUTPUT
GND
1
CT22
1UF
A
R82
3.01K
1206
C11
100PF
1206
3
ADP3338AKC-25
SOT-223
C82
0.1UF
805
Q5
2N7002
SOT23D
1
CT23
1UF
A
C83
0.1UF
805
3
R84
20.0K
1206
2
Q4
MMBT3904
SOT23D
1
AGND
2
AGND
PGND
AGND
MH1 MH2 MH3 MH4
5V
R142
0.00
RC05
A5V
R143
0.00
RC05
R137
0.00
RC05
R141
0.00
1206
SHGND
4
PGND
ANALOG
DEVICES
AGND
SHGND
Approvals
Date
Title
Drawn
Checked
Engineering
A
B
C
Size
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-TS101 EZ-KIT LITE - POWER SUPPLY
Board No.
C
Date
20 Cotton Road
Rev
A0163-2001
1.4
Sheet
1-19-2004_15:28
D
11
of
12
A
B
VDDINT
C107
0.1UF
805
C45
0.1UF
805
C44
0.1UF
805
C
D
VDDINT
C43
0.1UF
805
C42
0.1UF
805
C46
0.01UF
1206
C47
0.01UF
1206
C51
0.1UF
805
C50
0.1UF
805
C49
0.1UF
805
C48
0.1UF
805
C52
0.01UF
1206
C53
0.01UF
1206
C156
0.01UF
1206
3.3V
1
1
C114
0.1UF
805
U1
C115
0.1UF
805
C113
0.1UF
805
C116
0.1UF
805
C119
0.1UF
805
C118
0.1UF
805
C120
0.1UF
805
C117
0.1UF
805
C121
0.01UF
1206
C122
0.01UF
1206
C123
0.01UF
1206
C124
0.01UF
1206
C125
0.01UF
1206
C126
0.01UF
1206
C127
0.01UF
1206
C128
0.01UF
1206
U2
3.3V
3.3V
C155
0.1UF
805
C57
0.1UF
805
C56
0.1UF
805
C55
0.1UF
805
C54
0.1UF
805
C58
0.01UF
1206
C59
0.01UF
1206
C63
0.1UF
805
C62
0.1UF
805
C61
0.1UF
805
C60
0.1UF
805
C64
0.01UF
1206
C65
0.01UF
1206
C157
0.01UF
1206
2.5V
C130
0.1UF
805
2
C129
0.1UF
805
C131
0.1UF
805
C134
0.1UF
805
C133
0.1UF
805
C135
0.1UF
805
U19
C132
0.1UF
805
C136
0.01UF
1206
C137
0.01UF
1206
C138
0.01UF
1206
C139
0.01UF
1206
C140
0.01UF
1206
C141
0.01UF
1206
C142
0.01UF
1206
2
3.3V
C68
0.1UF
805
C67
0.1UF
805
C69
0.1UF
805
C66
0.1UF
805
C71
0.1UF
805
C72
0.1UF
805
C70
0.1UF
805
C73
0.1UF
805
C75
0.01UF
1206
C74
0.01UF
1206
C77
0.01UF
1206
C76
0.01UF
1206
C79
0.01UF
1206
C78
0.01UF
1206
C81
0.01UF
1206
C80
0.01UF
1206
3.3V
3.3V
3.3V
3.3V
C98
0.1UF
805
U3
3.3V
3
C87
0.1UF
805
3.3V
C88
0.1UF
805
C86
0.1UF
805
3.3V
C89
0.1UF
805
5V
C99
0.1UF
805
A5V
C100
0.1UF
805
5V
C101
0.1UF
805
A5V
C102
0.1UF
805
AGND
U4
A5V
U5
A5V
U6
3.3V
3.3V
C108
0.1UF
805
C109
0.1UF
805
C110
0.1UF
805
3.3V
C111
0.1UF
805
C112
0.1UF
805
C144
0.1UF
805
C143
0.1UF
805
C146
0.1UF
805
C145
0.1UF
805
3.3V
C103
0.1UF
805
U14
U15
3.3V
3.3V
U16
C104
0.1UF
805
3.3V
U17
3.3V
U18
3.3V
U20
3.3V
U21
3.3V
3.3V
3
3.3V
AGND
U7
U8
C172
0.1UF
805
U9
C147
0.1UF
805
C173
0.1UF
805
C148
0.1UF
805
C149
0.1UF
805
C150
0.1UF
805
C151
0.1UF
805
C152
0.1UF
805
C153
0.1UF
805
C154
0.1UF
805
C162
0.1UF
805
A5V
3.3V
U22
C158
0.1UF
805
C159
0.1UF
805
C160
0.1UF
805
C92
0.1UF
805
C91
0.1UF
805
C93
0.1UF
805
C90
0.1UF
805
C94
0.01UF
1206
C95
0.01UF
1206
C96
0.01UF
1206
C97
0.01UF
1206
U23
U24
U25
U26
C161
0.01UF
1206
ANALOG
DEVICES
4
AGND
U10
AGND
AGND
U11
U12
Approvals
U13
Date
Title
Drawn
Checked
Engineering
A
B
U27
C
Size
U29
U32
20 Cotton Road
Nashua, NH 03063
4
PH: 1-800-ANALOGD
ADSP-TS101 EZ-KIT LITE - CAPS
Board No.
C
Date
U28
Rev
A0163-2001
1.4
Sheet
1-19-2004_15:28
D
12
of
12
I
INDEX
A
AD1854 digital-to-analog converters (DACs),
1-11
AD1871 analog-to-digital converters (ADCs),
1-11
address data controls (ADC), 2-5
architecture, of this EZ-KIT Lite, 2-2
audio
connectors (P2-3), 2-12
interface, 1-11
B
bill of materials, A-1
~BMS boot memory select pins, 1-7, 2-3
board schematic, B-1
boot
modes, 2-6
mode switch (SW7), 2-6
C
CLKIN pins, 2-7
CLKOUT pins, 2-3
clock
frequency, 2-7
mode settings (SW7), 2-7
codecs, See AD1871, AD1854
connectors
diagram of locations, 1-4, 2-12
P11-13 (expansion), 2-3, 2-14
P14 (power), 2-15
P2-3 (audio), 2-12
P4 (USB), 2-13
P5 (JTAG), 2-13
P7-10 (link ports), 2-14
contents, of this EZ-KIT Lite package, 1-2
control impedance selection (SW7), 2-5
core
speed, 2-2, 2-7
voltage, 2-2
customer support, -xiv
D
D23-0 pins, 1-12
DIP switch SW7, 2-4, 2-5, 2-6, 2-7
drive strength selection (SW7), 2-5
E
example programs, 1-12
expansion interface, 2-3, 2-14
external
See also SDRAM
interrupts, 1-10
memory, -xi, 1-11
ports, 2-3
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
I-1
INDEX
F
L
features, of this EZ-KIT Lite, -x
FLAG
LEDs (LED7-LED4), 2-10
push buttons (SW2, SW4-5, SW9), 2-10
FLAG0_A (SW4) pins, 1-10, 2-11
FLAG0_B (SW5) pins, 1-10, 2-11
FLAG1_A (SW9) pins, 1-10, 2-11
FLAG1_B (SW2) pins, 1-10, 2-11
FLAG2_A (LED7) pins, 1-10, 2-10
FLAG2_B (LED4) pins, 1-10, 2-10
FLAG3_A (LED6) pins, 1-10, 1-11, 2-10
FLAG3_B (LED5) pins, 1-10, 1-11, 2-10
flash memory
boot memory select pins, 2-3
main/secondary, 1-7, 1-11
LEDs
diagram of locations, 1-4, 2-8
LED1 (USB monitor), 1-5, 2-8
LED2 (USB reset), 2-8
LED3 (power), 2-9
LED4-7 (FLAG3-2), 1-10, 2-10
LED8 (master reset), 2-9
LED9 (processor reset), 2-9
license restrictions, 1-7
link port
connectors (P7-10), 2-14
outputs, 2-5
G
general-purpose IO pins, -xi, 1-10, 2-11
I
input clock, 2-2
installation, of this EZ-KIT Lite, 1-5
internal memory, 1-7
interrupt
enable settings (SW2), 2-7
pins (IR3-0), 1-10
push buttons (SW3, SW6), 2-11
IRQ0_A (SW3) interrupt pins, 1-10, 2-11
IRQ0_B (SW6) interrupt pins, 1-10, 2-11
J
JTAG
connector (P5), 2-4, 2-13
emulation port, 2-4
programming cable, 1-11
M
memory map, of this EZ-KIT Lite, 1-7
N
notation conventions, -xxi
O
oscillators, 2-7
P
package contents, 1-2
power
connector (P14), 2-15
LED (LED3), 2-9
supply specifications, 2-15
programmable flag pins, See flags by name
(FLAGx)
push buttons
See also push buttons by name (SWx)
diagram of locations, 2-8
R
registration, of this product, 1-3
I-2
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
INDEX
reset
LEDs (LED2, LED8-9), 2-8
master (LED8), 2-9
processor, 1-9, 2-9
push button (SW1), 2-10
restrictions, of the license, 1-7
SW6 (IRQ0_B) push button, 1-10, 2-11
SW7 DIP switch, 2-4, 2-5, 2-6, 2-7
SW9 (FLAG1_A) push button, 1-10, 2-11
SYSCON registers, 1-8
system architecture, of this EZ-KIT Lite, 2-2
T
S
schematic, of this EZ-KIT Lite, B-1
SDRAM
external port connection, 2-3
interface, 1-8
start/end addresses, 1-7
SDRCON registers, 1-8
setup, of this EZ-KIT Lite, 1-4
specifications, of the power supply, 2-15
SQCTL registers, 1-9
SQSTAT registers, 1-9
startup, of this EZ-KIT Lite, 1-5
SW1 (reset) push buttons, 2-10
SW2 (FLAG1_B/interrupt) push button, 1-10,
2-7, 2-11
SW3 (IRQ0_A) push button, 1-10, 2-11
SW4 (FLAG0_A) push button, 1-10, 2-11
SW5 (FLAG0_B) push button, 1-10, 2-11
Target Options dialog box, 1-9
U
USB
cable, 1-3
connector (P4), 2-13
debug interface, 2-13
monitor LED (LED1), 2-8
reset LED (LED2), 2-8
V
VisualDSP++
documentation, -xix
environment, 1-5
online Help, -xix
voltage regulators, -xi
ADSP-TS101S EZ-KIT Lite Evaluation System Manual
I-3
INDEX
I-4
ADSP-TS101S EZ-KIT Lite Evaluation System Manual