UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com 120-V Boot, 3-A Peak, High Frequency, High-Side/Low-Side Driver Check for Samples: UCC27200A, UCC27201A FEATURES 1 • • 2 • • • • • • • • • • CONTENTS Specified from -40 °C to 140 °C Drives Two N-Channel MOSFETs in High-Side/Low-Side Configuration Maximum Boot Voltage 120 V Maximum VDD Voltage 20 V On-Chip 0.65-V VF, 0.6-Ω RD Bootstrap Diode Greater than 1 MHz of Operation 20-ns Propagation Delay Times 3-A Sink, 3-A Source Output Currents 8-ns Rise/7-ns Fall Time with 1000-pF Load 1-ns Delay Matching Under Voltage Lockout for High-Side and Low-Side Driver Offered in 8-Pin SOIC (D), PowerPad™ SOIC-8 (DDA), SON-8 (DRM), SON-9 (DRC) and SON-10 (DPR) Packages • • • • • • 2 Electrical Characteristics 4 Device Information 11 Application Information 14 Additional References 22 DESCRIPTION The UCC27200A/1A family of high frequency N-Channel MOSFET drivers include a 120-V bootstrap diode and high-side/low-side driver with independent inputs for maximum control flexibility. This allows for N-Channel MOSFET control in half-bridge, full-bridge, two-switch forward and active clamp forward converters. The low-side and the high-side gate drivers are independently controlled and matched to 1-ns between the turn-on and turn-off of each other. The UCC27200A/1A are based on the popular UCC27200/1 drivers, but offer some enhancements. In order to improve performance in noisy power supply environments the UCC27200A/1A has an enhanced ESD input structure and also has the ability to withstand a maximum of -18 V on its HS pin. APPLICATIONS • Device Ratings Power Supplies for Telecom, Datacom, and Merchant Markets Half-Bridge Applications and Full-Bridge Converters Isolated Bus Architecture Two-Switch Forward Converters Active-Clamp Forward Converters High Voltage Synchronous-Buck Converters Class-D Audio Amplifiers Simplified Application Diagram +12V +100V SECONDARY SIDE CIRCUIT VDD HB DRIVE HI LI CONTROL HI PWM CONTROLLER HO HS DRIVE LO LO UCC27200A/1A VSS ISOLATION AND FEEDBACK 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPad is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2011, Texas Instruments Incorporated UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. DESCRIPTION (CONT.) An on-chip bootstrap diode eliminates the external discrete diodes. Under-voltage lockout is provided for both the high-side and the low-side drivers forcing the outputs low if the drive voltage is below the specified threshold. Two versions of the UCC27200A are offered. The UCC27200A has high noise immune CMOS input thresholds while the UCC27201A has TTL compatible thresholds. Both devices are offered in an 8-pin SOIC(D), PowerPad™ SOIC-8(DDA), SON-8(DRM) package, a 9-pin SON-9(DRC) package and a 10-pin SON-10(DPR) package. ORDERING INFORMATION PACKAGED DEVICES (1) TEMPERATURE RANGE TA = TJ -40°C to +140°C (1) (2) (3) (4) (5) 2 INPUT COMPATIBILITY SOIC-8 (D) (2) PowerPad™ SOIC-8 (DDA) (2) SON-8 (DRM) (3) SON-9 (DRC) (4) CMOS UCC27200AD UCC27200ADDA UCC27200ADRM UCC27200ADRC N/A TTL UCC27201AD UCC27201ADDA UCC27201ADRM UCC27201ADRC UCC27201ADPR SON-10 (DPR) (5) These products are packaged in Lead (Pb)-Free and green lead finish of PdNiAu which is compatible with MSL level 1 at 255-260°C peak reflow temperature to be compatible with either lead free or Sn/Pb soldering operations. D (SOIC-8) and DDA (Power Pad™ SOIC-8) packages are available taped and reeled. Add R suffix to device type (e.g. UCC27200ADR) to order quantities of 2,500 devices per reel. DRM (SON-8) package comes either in a small reel of 250 pieces as part number UCC27200ADRMT, or larger reels of 3000 pieces as part number UCC27200A DRMR. DRC(SON-9) package comes either in a small reel of 250 pieces as part number UCC27200ADRCT, or large reels pieces as part number UCC27200ADRCR. DPR(SON-10) package comes either in a small reel of 250 pieces as part number UCC27201ADPRT, or large reels pieces as part number UCC27201ADPRR. Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com DEVICE RATINGS ABSOLUTE MAXIMUM RATINGS Over operating free-air temperature, unless noted, all voltages are with respect to VSS PARAMETER Supply voltage range, (2) (1) VALUE UNIT VDD -0.3 to 20 Input voltages on LI and HI, VLI, VHI -0.3 to 20 DC Output voltage on LO, VLO -0.3 to VDD + 0.3, Repetitive pulse <100 ns (3) -2 to VDD + 0.3 VHS – 0.3 to VHB + 0.3 DC Output voltage on HO, VHO Repetitive pulse <100 ns (3) DC Voltage on HS, VHS -1 to 120 Repetitive pulse <100 ns (3) -18 to 120 Voltage on HB, VHB -0.3 to 120 Voltage On HB-HS -0.3 to 20 Operating virtual junction temperature range, TJ -40 to +150 Storage temperature, TSTG -65 to +150 Lead temperature (soldering, 10 sec.) Power dissipation at TA = 25°C (D package) (4) 1.3 (4) 2.7 Power dissipation at TA = 25°C (DRM package) (4) 3.3 Power dissipation at TA = 25°C (DRC package) (4) W 2.86 Human body model 2000 CDM 1000 (2) (3) (4) °C +300 Power dissipation at TA = 25°C (DDA package) (1) V VHS - 2 to VHB + 0.3, (VHB - VHS <20) V Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to Vss. Currents are positive into, negative out of the specified terminal. Values are verified by characterization and are not production tested. This data was taken using the JEDEC proposed high-K test PCB. See the THERMAL CHARACTERISTICS section for details. RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) PARAMETER VDD Supply voltage range VHS Voltage on HS NOM 8 Voltage on HS, (repetitive pulse <100 ns) VHB MIN Voltage on HB UNIT 17 -1 105 -15 110 VHS + 8, VDD –1 VHS + 17, 115 -40 +140 Voltage slew rate on HS TJ MAX 12 50 Operating junction temperature range V V / ns Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A °C 3 UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com THERMAL INFORMATION THERMAL METRIC (1) (2) UCC27200A /UCC27201A UCC27200A /UCC27201A UCC27200A /UCC27201A DRM DRC DPR 8 PINS 9 PINS 10 PINS θJA Junction-to-ambient thermal resistance 36.2 43.7 34.8 θJCtop Junction-to-case (top) thermal resistance 41.6 49.9 32.1 θJB Junction-to-board thermal resistance 13.2 19.1 11.9 ψJT Junction-to-top characterization parameter 0.6 0.6 0.2 ψJB Junction-to-board characterization parameter 13.4 19.3 12.2 θJCbot Junction-to-case (bottom) thermal resistance 3.1 3.8 1.3 (1) (2) UNITS °C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. For thermal estimates of this device based on PCB copper area, see the TI PCB Thermal Calculator. THERMAL INFORMATION THERMAL METRIC (1) (2) UCC27200A /UCC27201A UCC27200A /UCC27201A D DDA 8 PINS 8 PINS θJA Junction-to-ambient thermal resistance 106.5 40.5 θJCtop Junction-to-case (top) thermal resistance 52.9 49.0 θJB Junction-to-board thermal resistance 46.6 10.2 ψJT Junction-to-top characterization parameter 9.6 3.1 ψJB Junction-to-board characterization parameter 46.1 9.7 θJCbot Junction-to-case (bottom) thermal resistance n/a 1.5 (1) (2) 4 UNITS °C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. For thermal estimates of this device based on PCB copper area, see the TI PCB Thermal Calculator. Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS over operating free-air temperature range, VDD = VHB = 12 V, VHS = VSS = 0 V, No load on LO or HO, TA = TJ = -40°C to +140°C, (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX 0.8 UNIT Supply Currents IDD VDD quiescent current VLI = VHI = 0 0.4 UCC27200A f = 500 kHz, CLOAD = 0 2.5 4 UCC27201A f = 500 kHz, CLOAD = 0 3.8 5.5 0.4 0.8 2.5 4 0.0005 1 IDDO VDD operating current IHB Boot voltage quiescent current VLI = VHI = 0 V IHBO Boot voltage operating current f = 500 kHz, CLOAD = 0 IHBS HB to VSS quiescent current VHS = VHB = 110 V IHBSO HB to VSS operating current f = 500 kHz, CLOAD = 0 0.1 mA uA mA Input VHIT Input rising threshold VLIT Input falling threshold 5.8 VIHYS Input voltage hysteresis 0.4 VHIT Input voltage threshold 1.7 VLIT Input voltage threshold VIHYS Input voltage Hysteresis RIN Input pulldown resistance UCC27200A UCC27201A 3 0.8 8 5.4 V 2.5 1.6 100 mV 100 200 350 6.2 7.1 7.8 kΩ Undervoltage Protection (UVLO) VDD rising threshold VDD threshold hysteresis 0.5 VHB rising threshold 5.8 VHB threshold hysteresis 6.7 7.2 V 0.4 Bootstrap Diode VF Low-current forward voltage I VDD - HB = 100 μA 0.65 0.85 VFI High-current forward voltage I VDD - HB = 100 mA 0.85 1.1 RD Dynamic resistance, ΔVF/ΔI I VDD - HB = 100 mA and 80 mA 0.6 1.0 ILO = 100 mA 0.18 0.4 TJ = -40 to 125°C ILO = -100 mA, VLOH = VDD VLO 0.25 0.4 TJ = -40 to 140°C ILO = -100 mA, VLOH = VDD VLO 0.25 0.42 V Ω LO Gate Driver VLOL VLOH Low level output voltage High level output voltage Peak pull-up current VLO = 0 V 3 Peak pull-down current VLO = 12 V 3 V A HO Gate Driver VHOL VHOH Low level output voltage IHO = 100 mA 0.18 0.4 TJ = -40 to 125°C IHO = -100 mA, VHOH = VHBVHO 0.25 0.4 TJ = -40 to 140°C IHO = -100 mA, VHOH = VHBVHO 0.25 0.42 High level output voltage Peak pull-up current VHO = 0 V 3 Peak pull-down current VHO = 12 V 3 V A Propagation Delays Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A 5 UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com ELECTRICAL CHARACTERISTICS (continued) over operating free-air temperature range, VDD = VHB = 12 V, VHS = VSS = 0 V, No load on LO or HO, TA = TJ = -40°C to +140°C, (unless otherwise noted) PARAMETER tDLFF tDHFF tDLRR tDHRR VLI falling to VLO falling VHI falling to VHO falling VLI rising to VLO rising VHI rising to VHO rising TYP MAX TJ = -40 to 125°C CLOAD = 0 TEST CONDITIONS MIN 20 45 TJ = -40 to 140°C CLOAD = 0 20 50 TJ = -40 to 125°C CLOAD = 0 20 45 TJ = -40 to 140°C CLOAD = 0 20 50 TJ = -40 to 125°C CLOAD = 0 20 45 TJ = -40 to 140°C CLOAD = 0 20 50 TJ = -40 to 125°C CLOAD = 0 20 45 TJ = -40 to 140°C CLOAD = 0 20 50 UNIT ns Delay Matching tMON LI ON, HI OFF 1 7 tMOFF LI OFF, HI ON 1 7 ns Output Rise and Fall Time tR LO, HO CLOAD = 1000 pF 8 tF LO, HO CLOAD = 1000 pF 7 tR LO, HO (3 V to 9 V) CLOAD = 0.1 μF 0.35 0.6 tF LO, HO (3 V to 9 V) CLOAD = 0.1 μF 0.3 0.6 ns us Miscellaneous Minimum input pulse width that changes the output Bootstrap diode turn-off time (1) (2) 6 50 IF = 20 mA, IREV = 0.5 A (1) (2) 20 ns Typical values for TA = 25°C IF: Forward current applied to bootstrap diode, IREV: Reverse current applied to bootstrap diode. Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com DEVICE INFORMATION SOIC-8(D) TOP VIEW 1 VDD Power Pad TM SOIC-8(DDA) TOP VIEW 8 VDD 1 LO 8 LO Exposed Thermal Die Pad HB 2 7 VSS HB 2 HO 3 6 LI HO 3 6 LI HS 4 5 HI HS 4 5 HI 9 LO 8 VSS 7 LI HO 3 6 HI HS 4 5 N/C VDD 1 8 LO HB 2 Exposed Thermal Die Pad* HB 2 7 VSS HO 3 6 LI 4 5 HI HS VSS SON-9 (DRC) TOP VIEW SON-8 (DRM) TOP VIEW VDD 1 7 Exposed Thermal Die Pad* SON-10 (DPR) TOP VIEW VDD 1 HB 2 HO 3 HS NC 10 LO 9 VSS 8 LI 4 7 HI 5 6 NC Exposed Thermal Die Pad NOTE Pin VSS and the exposed thermal die pad are internally connected. Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A 7 UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com PIN FUNCTIONS PIN PIN NAME DRM/D/DDA DRC DPR VDD 1 1 1 DESCRIPTION I Positive supply to the lower gate driver. De-couple this pin to VSS (GND). Typical decoupling capacitor range is 0.22 μF to 1.0 μF. HB 2 2 2 I High-side bootstrap supply. The bootstrap diode is on-chip but the external bootstrap capacitor is required. Connect positive side of the bootstrap capacitor to this pin. Typical range of HB bypass capacitor is 0.022 μF to 0.1 μF, the value is dependant on the gate charge of the high-side MOSFET however. HO 3 3 3 O High-side output. Connect to the gate of the high-side power MOSFET. HS 4 4 4 I High-side source connection. Connect to source of high-side power MOSFET. Connect negative side of bootstrap capacitor to this pin. HI 5 6 7 I High-side input. LI 6 7 8 I Low-side input. VSS 7 8 9 O Negative supply terminal for the device which is generally grounded. LO 8 9 10 O Low-side output. Connect to the gate of the low-side power MOSFET. N/C - 5 5/6 - No connection. Pins labeled N/C have no connection. PowerPAD™ Pad (1) Pad Pad - Connect to a large thermal mass trace or GND plane to dramatically improve thermal performance. (1) 8 I/O Pin VSS and the exposed thermal die pad are internally connected on the DDA and DRM packages only. Electrically referenced to VSS (GND). Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com FUNCTIONAL BLOCK DIAGRAM 2 HB 3 HO 4 HS 8 LO 7 VSS UVLO LEVEL SHIFT HI 5 VDD 1 UVLO LI 6 Figure 1. TIMING DIAGRAMS LI Input (HI, LI) HI TDLRR, TDHRR LO Output (HO, LO) TDLFF, TDHFF HO TMON TMOFF Figure 2. Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A 9 UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com TYPICAL CHARACTERISTICS UCC27200A IDD OPERATING CURRENT vs FREQUENCY UCC27201A IDD OPERATING CURRENT vs FREQUENCY 10.0 10.0 VDD = 12 V No Load on Outputs VDD = 12 V No Load on Outputs 150oC IDDO - Operating Current - mA IDDO - Operating Current - mA 25oC 150oC 125oC 1.0 o 25 C -40oC 0.1 125oC 1.0 -40oC 0.1 100 10 1000 100 10 Frequency - kHz Figure 3. Figure 4. BOOT VOLTAGE OPERATING CURRENT vs FREQUENCY HB TO VSS OPERATING CURRENT vs FREQUENCY 10.0 1.0 HB = 12 V No Load on Outputs IHBSO - Operating Current - mA HB = 12 V No Load on Outputs IHBO - Operating Current - mA 1000 Frequency - kHz 150oC 125oC 1.0 25oC -40oC 0.1 150oC 0.01 25oC 125oC 0.1 -40oC 0.001 10 100 1000 10 Frequency - kHz Figure 5. 10 100 1000 Frequency - kHz Figure 6. Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) UCC27200A INPUT THRESHOLD vs SUPPLY VOLTAGE UCC27201A INPUT THRESHOLD vs SUPPLY VOLTAGE 2.0 T= T = 25oC 25oC HI, LI - Input Threshold Voltage - V HI, LI - Input Threshold Voltage/VDD Voltage - % 50 Rising 48 46 Falling 44 42 1.8 Rising Falling 1.6 1.4 1.2 1.0 40 8 10 12 14 16 18 8 20 10 12 VDD - Supply Voltage - V 18 Figure 7. Figure 8. UCC27200A INPUT THRESHOLD vs TEMPERATURE UCC27201A INPUT THRESHOLD vs TEMPERATURE 50 20 2.0 VDD = 12 V VDD = 12 V HI, LI - Input Threshold Voltage - V HI, LI - Input Threshold Voltage/VDD Voltage - % 16 14 VDD - Supply Voltage - V 48 Rising 46 Falling 44 42 40 1.8 Rising 1.6 Falling 1.4 1.2 1.0 -50 -25 0 25 50 75 100 125 150 -50 -25 TA - Temperature - oC Figure 9. 0 25 50 75 100 125 150 TA - Temperature - oC Figure 10. Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A 11 UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) LO AND HO HIGH LEVEL OUTPUT VOLTAGE vs TEMPERATURE LO AND HO LOW LEVEL OUTPUT VOLTAGE vs TEMPERATURE 0.45 0.45 ILO = IHO = -100 mA 0.35 VDD = VHB = 16 V VDD = VHB = 12 V 0.30 VDD = VHB = 8 V 0.25 0.20 0.15 0.10 ILO = IHO = 100 mA 0.40 VOL - LO/HO Output Voltage - V VOH - LO/HO Output Voltage - V 0.40 VDD = VHB = 20 V 0.35 VDD = VHB = 16 V 0.30 VDD = VHB = 12 V 0.25 VDD = VHB = 8 V 0.20 0.15 0.10 0.05 0.05 VDD = VHB = 20 V 0.0 0.0 -50 -25 0 25 50 75 100 125 -50 150 -25 0 25 50 75 100 125 150 TA - Temperature - oC TA - Temperature - oC Figure 11. Figure 12. UNDERVOLTAGE LOCKOUT THRESHOLD vs TEMPERATURE UNDERVOLTAGE LOCKOUT THRESHOLD HYSTERESIS vs TEMPERATURE 7.8 0.8 7.6 0.7 7.4 Hysteresis - V Threshold - V 0.6 VDD Rising Threshold 7.2 7.0 6.8 6.6 VDD UVLO Hysteresis 0.5 0.4 HB UVLO Hysteresis 0.3 HB Rising Threshold 6.4 0.2 6.2 0.1 6.0 5.8 0 -50 -25 0 25 50 75 100 125 150 -50 -25 TA - Temperature - oC Figure 13. 12 0 25 50 75 100 125 150 TA - Temperature - oC Figure 14. Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) UCC27200A PROPAGATION DELAYS vs TEMPERATURE UCC27201A PROPAGATION DELAYS vs TEMPERATURE 36 36 VDD = VHD = 12 V 34 32 30 TDHRR 28 26 24 22 20 Propagation Delay - ns 32 Propagation Delay - ns VDD = VHB = 12 V 34 TDHFF TDLFF 18 30 28 26 24 22 TDLFF TDLRR 20 18 16 TDHFF 16 TDLRR 14 TDHRR 14 -50 -25 0 50 75 25 100 TA - Temperature - oC 125 150 -50 -25 0 25 50 75 TA - Temperature - 100 125 150 oC Figure 15. Figure 16. UCC27200A PROPAGATION DELAY vs SUPPLY VOLTAGE UCC27201A PROPAGATION DELAY vs SUPPLY VOLTAGE 26 26 T = 25oC T = 25oC 24 Propagation Delay - ns Propagation Delay - ns 24 22 LI Falling 20 LI Rising HI Falling LI Falling 22 LI Rising 20 HI Rising HI Rising 18 HI Falling 16 18 8 10 12 14 16 18 20 8 10 VDD = VHB - Supply Voltage - V Figure 17. 12 14 16 18 20 VDD = VHB - Supply Voltage - V Figure 18. Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A 13 UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) DELAY MATCHING vs TEMPERATURE OUTPUT CURRENT vs OUTPUT VOLTAGE 7 3.5 V DD = VHB = 12 V VDD = VHB = 12 V 6 3.0 ILO, IHO - Output Current - A Delay Matching - ns 5 4 UCC27200ATMOFF 3 UCC27201ATMOFF UCC27201ATMON UCC27200ATMON 2 1 0 -50 -25 0 25 50 75 100 125 2.5 Pull-Down Current Pull-Up Current 2.0 1.5 1.0 0.5 150 ? TA - Temperature - C 0 0 2 4 6 10 8 12 VLO, VHO - Output Voltage - V Figure 19. Figure 20. DIODE CURRENT vs DIODE VOLTAGE QUIESCENT CURRENT vs SUPPLY VOLTAGE 700 100.0 Inputs Low T = 25oC 600 IDD, IHB - Supply Current - mA Diode Current - mA 10.0 1.0 0.1 500 IHB 400 300 IDD 200 0.01 100 0 0.001 0.5 0.6 0.7 0.8 0.9 0 4 Diode Voltage - V Figure 21. 14 8 12 16 20 VDD, VHB - Supply Voltage - V Figure 22. Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com APPLICATION INFORMATION Functional Description The UCC27200A and UCC27201A are high-side/low-side drivers. The high-side and low-side each have independent inputs which allow maximum flexibility of input control signals in the application. The boot diode for the high-side driver bias supply is internal to the UCC27200A and UCC27201A. The UCC27200A is the CMOS compatible input version and the UCC27201A is the TTL or logic compatible version. The high-side driver is referenced to the switch node (HS) which is typically the source pin of the high side MOSFET and drain pin of the low-side MOSFET. The low-side driver is referenced to VSS which is typically ground. The functions contained are the input stages, UVLO protection, level shift, boot diode, and output driver stages. NOTE The term “UCC2720x” applies to both the UCC27200A and UCC27201A. Input Stages The input stages provide the interface to the PWM output signals. The input impedance of the UCC27200A is 200 kΩ nominal and input capacitance is approximately 2 pF. The 200 kΩ is a pull-down resistance to Vss (ground). The CMOS compatible input of the UCC27200A provides a rising threshold of 48% of VDD and falling threshold of 45% of VDD. The inputs of the UCC27200A are intended to be driven from 0 to VDD levels. The input stages of the UCC27201A incorporate an open drain configuration to provide the lower input thresholds. The input impedance is 200 kΩ nominal and input capacitance is approximately 4 pF. The 200 kΩ is a pull-down resistance to VSS (ground). The logic level compatible input provides a rising threshold of 1.7 V and a falling threshold of 1.6 V. UVLO (Under Voltage Lockout) The bias supplies for the high-side and low-side drivers have UVLO protection. VDD as well as VHB to VHS differential voltages are monitored. The VDD UVLO disables both drivers when VDD is below the specified threshold. The rising VDD threshold is 7.1 V with 0.5-V hysteresis. The VHB UVLO disables only the high-side driver when the VHB to VHS differential voltage is below the specified threshold. The VHB UVLO rising threshold is 6.7 V with 0.4-V hysteresis. Level Shift The level shift circuit is the interface from the high-side input to the high-side driver stage which is referenced to the switch node (HS). The level shift allows control of the HO output referenced to the HS pin and provides excellent delay matching with the low-side driver. Boot Diode The boot diode necessary to generate the high-side bias is included in the UCC2720x family of drivers. The diode anode is connected to VDD and cathode connected to VHB. With the VHB capacitor connected to HB and the HS pins, the VHB capacitor charge is refreshed every switching cycle when HS transitions to ground. The boot diode provides fast recovery times, low diode resistance, and voltage rating margin to allow for efficient and reliable operation. Output Stages The output stages are the interface to the power MOSFETs in the power train. High slew rate, low resistance and high peak current capability of both output drivers allow for efficient switching of the power MOSFETs. The low-side output stage is referenced from VDD to VSS and the high-side is referenced from VHB to VHS. Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A 15 UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com Design Tips Switching the MOSFETs Achieving optimum drive performance at high frequency efficiently requires special attention to layout and minimizing parasitic inductances. Care must be taken at the driver die and package level as well as the PCB layout to reduce parasitic inductances as much as possible. Figure 23 shows the main parasitic inductance elements and current flow paths during the turn ON and OFF of the MOSFET by charging and discharging its CGS capacitance. L bond wire L pin L trace 1 VDD I SOURCE Rsource Driver Output Stage Cvdd L pin L trace L bond wire Rg 8 LO I sink Rsink L pin L trace L bond wire 7 Cgs L trace Vss Figure 23. MOSFET Drive Paths and Circuit Parasitics 16 Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com The ISOURCE current charges the CGS gate capacitor and the ISINK current discharges it. The rise and fall time of the voltage across the gate to source defines how quickly the MOSFET can be switched. Based on actual measurements, the analytical curves in Figure 24 and Figure 25 indicate the output voltage and current of the drivers during the discharge of the load capacitor. Figure 24 shows voltage and current as a function of time. Figure 25 indicates the relationship of voltage and current during fast switching. These figures demonstrate the actual switching process and limitations due to parasitic inductances. 12 11 12 11 10 10 9 8 9 6 8 5 7 4 3 LO Voltage, V LO Falling, V or A 7 2 1 0 1 2 5 4 3 2 3 4 5 6 1 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 0 1 t, ns Voltage 2 Current 3 2 1 0 1 2 3 4 5 LO Current, A Figure 24. Turn-Off Voltage and Current vs Time Figure 25. Turn-Off Voltage and Current Switching Diagram Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A 17 UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com Turning off the MOSFET needs to be achieved as fast as possible to minimize switching losses. For this reason the UCC2720x drivers are designed for high peak currents and low output resistance. The sink capability is specified as 0.18 V at 100-mA dc current implying 1.8-Ω RDS(on). With 12-V drive voltage, no parasitic inductance and a linear resistance, one would expect initial sink current amplitude of 6.7 A for both high-side and low-side drivers. Assuming a pure R-C discharge circuit of the gate capacitor, one would expect the voltage and current waveforms to be exponential. Due to the parasitic inductances and non-linear resistance of the driver MOSFET’S, the actual waveforms have some ringing and the peak-sink current of the drivers is approximately 3.3 A as shown in Figure 20. The overall parasitic inductance of the drive circuit is estimated at 4 nH. The internal parasitic inductance of the SOIC-8 package is estimated to be 2 nH including bond wires and leads. The SON-8 package reduces the internal parasitic inductances by more than 50%. Actual measured waveforms are shown in Figure 26 and Figure 27. As shown, the typical rise time of 8 ns and fall time of 7 ns is conservatively rated. UCC27200A UCC27200A Figure 26. VLO and VHO Rise Time, 1-nF Load, 5 ns/Div 18 Figure 27. VLO and VHO Fall Time, 1-nF Load, 5-ns/Div Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com Dynamic Switching of the MOSFETs The true behavior of MOSFETS presents a dynamic capacitive load primarily at the gate to source threshold voltage. Using the turn off case as the example, when the gate to source threshold voltage is reached the drain voltage starts rising, the drain to gate parasitic capacitance couples charge into the gate resulting in the turn off plateau. The relatively low threshold voltages of many MOSFETS and the increased charge that has to be removed (Miller charge) makes good driver performance necessary for efficient switching. An open loop half bridge power converter was utilized to evaluate performance in actual applications. The schematic of the half-bridge converter is shown in Figure 30. The turn off waveforms of the UCC27200A driving two MOSFETs in parallel is shown in Figure 28 and Figure 29. UCC27200A UCC27200A Figure 28. VLO Fall Time in Half-Bridge Converter Figure 29. VHO Fall Time in Half-Bridge Converter Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A 19 UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 + + + www.ti.com Figure 30. Open Loop Half-Bridge Converter 20 Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com Delay Matching and Narrow Pulse Widths The total delays encountered in the PWM, driver and power stage need to be considered for a number of reasons, primarily delay in current limit response. Also to be considered are differences in delays between the drivers which can lead to various concerns depending on the topology. The sync-buck topology switching requires careful selection of dead-time between the high- and low-side switches to avoid 1) cross conduction and 2) excessive body diode conduction. Bridge topologies can be affected by a resulting volt-sec imbalance on the transformer if there is imbalance in the high and low side pulse widths in a steady state condition. Narrow pulse width performance is an important consideration when transient and short circuit conditions are encountered. Although there may be relatively long steady state PWM output-driver-MOSFET signals, very narrow pulses may be encountered in 1) soft start, 2) large load transients, and 3) short circuit conditions. The UCC2720x driver family offers excellent performance regarding high and low-side driver delay matching and narrow pulse width performance. The delay matching waveforms are shown in Figure 31 and Figure 32. The UCC2720x driver narrow pulse performance is shown in Figure 33 and Figure 34. Figure 31. VLO and VHO Rising Edge Delay Matching Figure 32. VLO and VHO Falling Edge Delay Matching Figure 33. 20-ns Input Pulse Delay Matching Figure 34. 10-ns Input Pulse Delay Matching Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A 21 UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com Boot Diode Performance The UCC2720x family of drivers incorporates the bootstrap diode necessary to generate the high side bias internally. The characteristics of this diode are important to achieve efficient, reliable operation. The dc characteristics to consider are VF and dynamic resistance. A low VF and high dynamic resistance results in a high forward voltage during charging of the bootstrap capacitor. The UCC2720x has a boot diode rated at 0.65-V VF and dynamic resistance of 0.6 Ω for reliable charge transfer to the bootstrap capacitor. The dynamic characteristics to consider are diode recovery time and stored charge. Diode recovery times that are specified with no conditions can be misleading. Diode recovery times at no forward current (IF) can be noticeably less than with forward current applied. The UCC2720x boot diode recovery is specified at 20ns at IF = 20 mA, IREV = 0.5 A. At 0 mA IF the reverse recovery time is 15 ns. Another less obvious consideration is how the stored charge of the diode is affected by applied voltage. On every switching transition when the HS node transitions from low to high, charge is removed from the boot capacitor to charge the capacitance of the reverse biased diode. This is a portion of the driver power losses and reduces the voltage on the HB capacitor. At higher applied voltages, the stored charge of the UCC2720x PN diode is often less than a comparable Schottky diode. Layout Recommendations To • • • • • • • • 22 improve the switching characteristics and efficiency of a design, the following layout rules should be followed. Locate the driver as close as possible to the MOSFETs. Locate the VDD and VHB (bootstrap) capacitors as close as possible to the driver. Pay close attention to the GND trace. Use the thermal pad of the DDA and DRM package as GND by connecting it to the VSS pin (GND). Note: The GND trace from the driver goes directly to the source of the MOSFET but should not be in the high current path of the MOSFET(S) drain or source current. Use similar rules for the HS node as for GND for the high side driver. Use wide traces for LO and HO closely following the associated GND or HS traces. 60 mil to 100 mil width is preferable where possible. Use as least two or more vias if the driver outputs or SW node needs to be routed from one layer to another. For GND the number of vias needs to be a consideration of the thermal pad requirements as well as parasitic inductance. Avoid LI and HI (driver input) going close to the HS node or any other high dV/dT traces that can induce significant noise into the relatively high impedance leads. Keep in mind that a poor layout can cause a significant drop in efficiency versus a good PCB layout and can even lead to decreased reliability of the whole system. Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A UCC27200A, UCC27201A SLUSAF9A – FEBRUARY 2011 – REVISED DECEMBER 2011 www.ti.com Figure 35. Example Component Placement Additional References These references and links to additional information may be found at www.ti.com. 1. Additional layout guidelines for PCB land patterns may be found in Application Brief SLUA271 2. Additional thermal performance guidelines may be found in Application Reports SLMA002A and SLMA004 SPACER REVISION HISTORY Changes from Original (February 2011) to Revision A Page • Added SON-10 (DPR) Package to the List of FEATURES .................................................................................................. 1 • Added SON-10 (DPR) Package to the DESCRIPTION ........................................................................................................ 2 • Added the SON-10 package to the ORDERING INFORMATION table ............................................................................... 2 • Added ordering information for the SON-10 (DPR) .............................................................................................................. 2 • Added note, "DPR(SON-10) package comes either in a small reel of 250 pieces as part number UCC27200ADPRT, or large reels pieces as part number UCC27200ADPRR." .................................................................................................. 2 • Added the SON-10 package to the THERMAL INFORMATION table ................................................................................. 4 • Changed the "Minimum input pulse width" value From: 50 ns Max To: 50 ns Typ .............................................................. 6 • Added the SON-10 package Pinout ...................................................................................................................................... 7 • Changed the PIN FUNCTIONS table ................................................................................................................................... 8 • Added Additional PIN FUNCTIONS information. .................................................................................................................. 8 Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated Product Folder Link(s): UCC27200A UCC27201A 23 PACKAGE OPTION ADDENDUM www.ti.com 26-Dec-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) UCC27200AD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC27200ADDA ACTIVE SO PowerPAD DDA 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC27200ADDAR ACTIVE SO PowerPAD DDA 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC27200ADR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC27200ADRM PREVIEW VSON DRM 8 UCC27200ADRMR ACTIVE VSON DRM 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC27200ADRMT ACTIVE VSON DRM 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC27201AD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC27201ADDA ACTIVE SO PowerPAD DDA 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC27201ADDAR ACTIVE SO PowerPAD DDA 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC27201ADPRR ACTIVE WSON DPR 10 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC27201ADPRT ACTIVE WSON DPR 10 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC27201ADR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC27201ADRCR ACTIVE SON DRC 9 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC27201ADRCT ACTIVE SON DRC 9 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TBD TBD Call TI Call TI UCC27201ADRM PREVIEW VSON DRM 8 UCC27201ADRMR ACTIVE VSON DRM 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC27201ADRMT ACTIVE VSON DRM 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 Call TI Samples Call TI PACKAGE OPTION ADDENDUM www.ti.com 26-Dec-2011 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 28-Jan-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant UCC27200ADDAR SO Power PAD DDA 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UCC27201ADDAR SO Power PAD DDA 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UCC27201ADPRR WSON DPR 10 3000 330.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 UCC27201ADPRT WSON DPR 10 250 180.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 UCC27201ADRCR SON DRC 9 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 UCC27201ADRMR VSON DRM 8 3000 330.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 UCC27201ADRMT VSON DRM 8 250 180.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 28-Jan-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UCC27200ADDAR SO PowerPAD DDA 8 2500 346.0 346.0 29.0 UCC27201ADDAR SO PowerPAD DDA 8 2500 346.0 346.0 29.0 UCC27201ADPRR WSON DPR 10 3000 346.0 346.0 29.0 UCC27201ADPRT WSON DPR 10 250 210.0 185.0 35.0 UCC27201ADRCR SON DRC 9 3000 346.0 346.0 29.0 UCC27201ADRMR VSON DRM 8 3000 346.0 346.0 29.0 UCC27201ADRMT VSON DRM 8 250 210.0 185.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated