TRUMPower 120 WATT MEDICAL POWER ADAPTERS D E S C R IP T IO N TMP120 SERIES The TMP120 series of AC/DC switching power adapters are for 96 to 120 watts of continuous output power. They are enclosed in a 94V-1 rated case with an IEC 320/C14 or C18 inlet to mate with interchangeable AC power cord for world-wide use. All models meet CISPR 11 and FCC class B emission limits, and are designed for medical applications. Class I, Class II (LVD) RoHS F E AT U R E S ‧ ‧ ‧ ‧ ‧ ‧ ‧ Low safety ground leakage current Optional output connectors 100% burn-in 9 0 t o 2 6 4 VAC w i d e i n p u t r a n g e O v e r v o l ta g e a n d o v e r c u r r e n t p r o t e c t i o n s Optional IEC 320/C18 inlet with class II insulation C o m p l i a n t w i t h C E C a n d E n e r g y S ta r e f f i c i e n c y l e v e l I V r e q u i r e m e n ts ‧ No load power consumption less than 0.5W ‧ Av e r a g e a c t i v e e f f i c i e n c y ≥ 8 5 % ‧ C o m p l i a n t w i t h R o H S r e q u i r e m e n ts S a f e t y Sta n d a r d A p p r o va l s ： UL 60601-1 CSA C22.2 No. 601.1 TÜV EN60601-1 I N P U T S P E C I F I C AT I O N S GENERAL SPECIFICATIONS I n p u t v o l ta g e ： Switching frequency： Power factor： Efficiency： Hold-up time： Line regulation： Input frequency： Input current： 90 to 264VAC 47 to 63Hz 1.60A (rms) for 115 VAC 0.80A (rms) for 230 VAC 90µA max. @ 115 VAC/60Hz Earth leakage current： 150µA max. @ 230 VAC/50Hz (Class I) E n c l o s u r e l e a k a g e c u r r e n t : 90µA max. @ 264 VAC/50Hz (Class II) OUTPUT SPECIFICATIONS Output voltage/current： Total output power： Ripple and noise： Overvoltage protection： Overcurrent protection： Temperature coefficient： Transient response： See rating chart 120 watts maximum 2% peak to peak maximum Provided on output #1 only; set at 112 -140% of its nominal output voltage All outputs protected to short circuit conditions All outputs ±0.04%/ºC maximum Maximum excursion of 4% or better on all models, recovering to 1% of final value within 500µs after a 25% step load change E N V I R O N M E N TA L S P E C I F I C AT I O N S Operating temperature： Storage temperature： Relative humidity： Derating： 50KHz ~ 110KHz 0.98 typical at 115VAC 85% min. 15 msec minimum at 115VAC ±0.5% maximum at full load Inrush current： 60 amps @ 115VAC or 90 amps @230VAC, at 25ºC cold start Withstand voltage： 4000VAC from input to output 1500VAC from input to ground 500VAC from output to ground MTBF： 150,000 hours minimum at full load at 25ºC ambient, calculated per MIL-HDBK-217F EMC Performance (EN60601-1-2: 2001) E N 5 5 0 11 : Class B conducted, Class B radiated FCC: Class B conducted, Class B radiated VCCI: Class B conducted, Class B radiated EN61000-3-2: Harmonic distortion, Class A and D EN61000-3-3: Line flicker EN61000-4-2: ESD, ±8KV air and ±6KV contact EN61000-4-3: Radiated immunity, 3V/m EN61000-4-4: Fast transient/burst, ±2KV EN61000-4-5: Surge, ±1KV diff, ±2KV com. EN61000-4-6: Conducted immunity, 3Vrms EN61000-4-8: Magnetic field immunity, 3A/m E N 6 1 0 0 0 - 4 - 11 : Voltage dips, 30% reduction for 500ms, 60% reduction for 100ms and >95% reduction for 10ms 0 ºC t o + 6 0 ºC - 4 0 ºC t o + 8 5 ºC 5% to 95% non-condensing Derate from 100% at +40ºC linearly to 50% at +60ºC Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● Fax: 408-988-6622 ● email: [email protected] ● Website: www.TRUMPower.com MEDICAL GRADE TMP120 SERIES OUTPUT VOLTAGE/CURRENT RATING CHART Output Product No. Vnom. Imin. Imax. Tol. Maximum Output Power TMP120-12 12V 0A 8.0A 5% 96W TMP120-15 15V 0A 7.0A 5% 105W TMP120-18 18V 0A 6.67A 5% 120W TMP120-19 19V 0A 6.32A 5% 120W TMP120-20 20V 0A 6.0A 5% 120W TMP120-24 24V 0A 5.0A 5% 120W TMP120-30 30V 0A 4.0A 5% 120W TMP120-36 36V 0A 3.34A 5% 120W TMP120-48 48V 0A 2.5A 5% 120W NOTES: 1. Ripple and noise: Peak-to-peak with 20MHz bandwidth and 10µF tantalum capacitor in parallel with a 0.1µF ceramic capacitor at rated line voltage and load ranges. 2. To order a model with IEC320/C18 inlet and class II insulation, add “C2”, e.g. TMP120-12-C2. MECHANICAL SPECIFICATIONS NOTES: 1. Dimensions shown in inch [mm] 2. Tolerance 0.02 [0.5] maximum 3. Weight: 780 grams approx. 4. Standard output connector is a male 4-pin power DIN. Please consult TRUMPower for other connector options 5. TMP120-12 and TMP120-15 output connectors are without lock. PIN CHART PIN Product No. TMP120-12 TMP120-18 TMP120-20 TMP120-30 TMP120-48 TMP120-15 TMP120-19 TMP120-24 TMP120-36 1 2 3 4 Shell Return Output +V Return Output +V AC Ground Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● Fax: 408-988-6622 ● email: [email protected] ● Website: www.TRUMPower.com