SHARP S102T02

S102T02 Series
S202T02 Series
IT(rms)≤2A, Zero Cross type
Low profile SIP 4pin
Triac output SSR
S102T02 Series
S202T02 Series
∗
Non-zero cross type is also available. (S102T01 Series/
S202T01 Series)
■ Description
■ Agency approvals/Compliance
S102T02 Series and S202T02 Series Solid State
Relays (SSR) are an integration of an infrared emitting
diode (IRED), a Phototriac Detector and a main output
Triac. These devices are ideally suited for controlling
high voltage AC loads with solid state reliability while
providing 3.0kV isolation (Viso(rms)) from input to output.
1. Recognized by UL508, file No. E94758 (as models No.
S102T02/S202T02)
2. Approved by CSA 22.2 No.14, file No. LR63705 (as
models No. S102T02/S202T02)
3. Package resin : UL flammability grade (94V-0)
■ Applications
1. Isolated interface between high voltage AC devices
and lower voltage DC control circuitry.
2. Switching motors, fans, heaters, solenoids, and
valves.
3. Power control in applications such as lighting and
temperature control equipment.
■ Features
1. Output current, IT(rms)≤2.0A
2. Zero crossing functionary (VOX : MAX. 35V)
3. Slim 4 pin low profile SIP package
4. High repetitive peak off-state voltage
(VDRM : 600V, S202T02 Series)
(VDRM : 400V, S102T02 Series)
5. High isolation voltage between input and output
(Viso(rms) : 3.0kV)
6. Lead-free terminal components are also available
(see Model Line-up section in this datasheet)
7. Screw hole for heat sink
Notice The content of data sheet is subject to change without prior notice.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
1
Sheet No.:D4-A01601EN
Date Apr. 28. 2004
© SHARP Corporation
S102T02 Series
S202T02 Series
■ Internal Connection Diagram
1
2
3
4
1
2
Output (Triac T1)
Output (Triac T2)
Input (+)
Input (−)
3 4
Zero Crossing Circuit
■ Outline Dimensions
(Unit : mm)
Common to pin No.2
1
2
1.8±0.3
0.4±0.1
(1.8)
3 4
1.6±0.2
1
2
(3.5)
1.8±0.3
(5.08)
Product mass : approx. 3.5g
Date code (2 digit)
3-1.2±0.2
3-1.4±0.2
4-0.8±0.2
0.4±0.1
(1.8)
3 4
(2.54)
(3.8)
(2.54)
(10.16)
+ −
10±0.2
2A265VAC
~ ∗
3.8MIN.
4-0.8±0.2
S202T02
6.2
Date code (2 digit)
3-1.2±0.2
3-1.4±0.2
3±0.2
Common to pin No.2
UL mark
CSA mark
Epoxy resin
MIN.
(3.5)
(3.8)
(5.08)
+ −
(0.8)
3.8MIN.
6.2
1.6±0.2
0.2MIN.
2A125VAC
~ ∗
(25.8)
S102T02
10±0.2
11.5±0.2
UL mark
CSA mark
Epoxy resin
6.4±0.2
φ3.7±0.2
(0.8)
Common to pin No.2
0.2MIN.
3±0.2
4.5±0.3
6.4±0.2
φ3.7±0.2
MIN.
(25.8)
4.5±0.3
Common to pin No.2
4±0.2
7±0.2
11.5±0.2
7
23±0.2
4±0.2
±0.2
1.8±0.2
23±0.2
1.8±0.2
S202T02
S102T02
(10.16)
Product mass : approx. 3.5g
∗
: Do not allow external connection.
( ) : Typical dimensions
Sheet No.: D4-A01601EN
2
S102T02 Series
S202T02 Series
Date code (2 digit)
A.D.
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2001
1st digit
Year of production
A.D
Mark
2002
A
2003
B
2004
C
2005
D
2006
E
2007
F
2008
H
2009
J
2010
K
2011
L
2012
M
··
N
·
Mark
P
R
S
T
U
V
W
X
A
B
C
··
·
2nd digit
Month of production
Month
Mark
January
1
February
2
March
3
April
4
May
5
June
6
July
7
August
8
September
9
October
O
November
N
December
D
repeats in a 20 year cycle
Country of origin
Japan
Rank mark
There is no rank mark indicator and currently there are no rank offered for this device.
Sheet No.: D4-A01601EN
3
S102T02 Series
S202T02 Series
(Ta=25˚C)
Parameter
Symbol Rating
Unit
*3
Forward current
IF
50
mA
Input
Reverse voltage
VR
6
V
RMS ON-state current
IT (rms)
2 *3
A
*4
Peak one cycle surge current
Isurge
20
A
Repetitive
S102T02
400
VDRM
V
peak OFF-state voltage S202T02
600
Output
Non-Repetitive
S102T02
400
VDSM
V
peak OFF-state voltage S202T02
600
Critical rate of rise of ON-state current dIT/dt
40
A/µs
Operating frequency
45 to 65
f
Hz
*1
Isolation voltage
3.0
Viso(rms)
kV
Operating temperature
Topr −25 to +100
˚C
Storage temperature
Tstg −30 to +125
˚C
*2 Soldering temperature
Tsol
260
˚C
1.5mm
■ Absolute Maximum Ratings
Soldering area
*1 40 to 60%RH, AC for 1minute, f=60Hz
*2 For 10s
*3 Refer to Fig.1, Fig.2
*4 f=60Hz sine wave, Tj=25˚C start
■ Electro-optical Characteristics
(Ta=25˚C)
Parameter
Symbol
Conditions
MIN.
−
VF
IF=20mA
Forward voltage
Input
−
IR
VR=3V
Reverse current
IDRM
−
VD=VDRM
Repetitive peak OFF-state current
V
(rms)
I
(rms)=2A,
Resistance
load,
I
=20mA
−
ON-state voltage
T
T
F
IH
−
−
Output Holding current
dV/dt
VD=2/3•VDRM
30
Critical rate of rise of OFF-state voltage
Critical rate of rise of OFF-state voltage at commutaion (dV/dt)c Tj=125˚C, VD=2/3•VDRM, dIT/dt=−1.0A/ms
4
IFT
VD=6V, RL=30Ω
Minimum trigger current
−
VOX
IF=8mA
Zero cross voltage
−
RISO
DC500V, 40 to 60%RH
Isolation resistance
1010
VD(rms)=100V, AC50Hz, IF=20mA
−
S102T02
IT(rms)=2A, Resistance load
Transfer Turn-on time
ton
VD(rms)=200V, AC50Hz, IF=20mA
charac−
S202T02
teristics
IT(rms)=2A, Resistance load
VD(rms)=100V, AC50Hz, IF=20mA
−
S102T02
IT(rms)=2A, Resistance load
toff
Turn-off time
VD(rms)=200V, AC50Hz, IF=20mA
−
S202T02
IT(rms)=2A, Resistance load
TYP.
1.2
−
−
−
−
−
−
−
−
−
MAX.
1.4
100
100
1.7
25
−
−
8
35
−
−
10
Unit
V
µA
µA
V
mA
V/µs
V/µs
mA
V
Ω
ms
−
10
−
10
−
10
ms
Sheet No.: D4-A01601EN
4
S102T02 Series
S202T02 Series
■ Model Line-up (1) (Lead-free terminal components)
25pcs/sleeve
VDRM
[V]
IFT[mA]
(VD=6V,
RL=30Ω)
S102T02F
S202T02F
400
600
MAX.8
MAX.8
Sleeve
Shipping Package
Model No.
■ Model Line-up (2) (Lead solder plating components)
25pcs/sleeve
VDRM
[V]
IFT[mA]
(VD=6V,
RL=30Ω)
S102T02
S202T02
400
600
MAX.8
MAX.8
Sleeve
Shipping Package
Model No.
Please contact a local SHARP sales representative to see the actual status of the production.
Sheet No.: D4-A01601EN
5
S102T02 Series
S202T02 Series
Fig.2 RMS ON-state Current vs.
Ambient Temperature
60
3.0
50
2.5
RMS ON-state current IT(rms) (A)
Forward current IF (mA)
Fig.1 Forward Current vs. Ambient
Temperature
40
30
20
10
0
−25
0
25
50
75
100
2.0
1.5
1.0
0.5
0
−25
125
0
40 50
75
100
125
Ambient temperature Ta (˚C)
Ambient temperature Ta (˚C)
Fig.3 Forward Current vs. Forward Voltage
Fig.4 Surge Current vs. Power-on Cycle
25
100
f=60Hz
Tj=25˚C start
20
Ta=75˚C
50˚C
Surge current Isurge (A)
Forward current IF (mA)
25
10
25˚C
0˚C
−25˚C
1
15
10
5
0.1
0.6
0
0.8
1.0
1.2
1.4
1.6
1
1.8
10
Forward voltage VF (mA)
Power-on cycle (Times)
Fig.5 Minimum Trigger Current vs.
Ambient Temperature
Fig.6 Maximum ON-state Power Dissipation
vs. RMS ON-state Current
2.5
Maximum ON-state power dissipation (W)
10
Minimum trigger current IFT (mA)
VD=6V
8
6
4
2
0
−25
100
Ta=25˚C
2
1.5
1
0.5
0
0
25
50
75
0
100
0.5
1
1.5
2
RMS ON-state current IT (rms)(A)
Ambient temperature Ta (˚C)
Sheet No.: D4-A01601EN
6
S102T02 Series
S202T02 Series
Fig.7-a Repetitive Peak OFF-state Current vs.
Ambient Temperature (S102T02)
Fig.7-b Repetitive Peak OFF-state Current vs.
Ambient Temperature (S202T02)
10−3
10−3
VD=600V
Repetitive peak OFF-state current IDRM (A)
Repetitive peak OFF-state current IDRM (A)
VD=400V
10−4
10−5
10−6
10−7
10−8
10−9
−25
0
25
50
75
10−4
10−5
10−6
10−7
10−8
10−9
−25
100
0
25
50
75
100
Ambient temperature Ta (˚C)
Ambient temperature Ta (˚C)
Remarks : Please be aware that all data in the graph are just for reference.
Sheet No.: D4-A01601EN
7
S102T02 Series
S202T02 Series
■ Design Considerations
● Recommended Operating Conditions
Input
Output
Symbol
Parameter
Input signal current at ON state
IF(ON)
Input signal current at OFF state
IF(OFF)
S102T02
Load supply voltage
VOUT(rms)
S202T02
Load supply current
Frequency
Operating temperature
IOUT(rms)
f
Topr
Conditions
−
−
−
Locate snubber circuit between output terminals
(Cs=0.022µF, Rs=47Ω)
−
−
MIN.
16
0
80
80
0.1
47
−20
MAX.
24
0.1
120
240
IT(rms)
×80%(∗)
63
80
Unit
mA
mA
V
mA
Hz
˚C
(∗) See Fig.2 about derating curve (IT(rms) vs. ambient temperature).
● Design guide
In order for the SSR to turn off, the triggering current (lF) must be 0.1mA or less.
When the input current (IF) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, VD, increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit vales to start with : Cs=0.022µF and Rs=47Ω. The operation of the SSR
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenoids.
Following the procedure outlined above should provide sufficient results.
For over voltage protection, a Varistor may be used.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main output triac as possible.
Particular attention needs to be paid when utilizing SSRs that incorporate zero crossing circuitry.
If the phase difference between the voltage and the current at the output pins is large enough, zero crossing
type SSRs cannot be used. The result, if zero crossing SSRs are used under this condition, is that the SSR
may not turn on and off irregardless of the input current. In this case, only a non zero cross type SSR should
be used in combination with the above mentioned snubber circuit selection process.
The load current should be within the bounds of derating curve. (Refer to Fig.2)
Also, please use the optional heat sink when necessary.
In case the optional heat sink is used and the isolation voltage between the device and the optional heat sink
is needed, please locate the insulation sheet between the device and the heat sink.
When the optional heat sink is equipped, please set up the M3 screw-fastening torque at 0.3 to 0.5N•m.
In order to dissipate the heat generated from the inside of device effectively, please follow the below suggestions.
Sheet No.: D4-A01601EN
8
S102T02 Series
S202T02 Series
(a) Make sure there are no warps or bumps on the heat sink, insulation sheet and device surface.
(b) Make sure there are no metal dusts or burrs attached onto the heat sink, insulation sheet and device surface.
(c) Make sure silicone grease is evenly spread out on the heat sink, insulation sheet and device surface.
Silicone grease to be used is as follows;
1) There is no aged deterioration within the operating temperature ranges.
2) Base oil of grease is hardly separated and is hardly permeated in the device.
3) Even if base oil is separated and permeated in the device, it should not degrade the function of a device.
Recommended grease : G-746 (Shin-Etsu Chemical Co., Ltd.)
: G-747 (Shin-Etsu Chemical Co., Ltd.)
: SC102 (Dow Corning Toray Silicone Co., Ltd.)
In case the optional heat sink is screwed up, please solder after screwed.
In case of the lead frame bending, please keep the following minimum distance and avoid any mechanical
stress between the base of terminals and the molding resin.
3.8mm MIN.
Some of AC electromagnetic counters or solenoids have built-in rectifier such as the diode.
In this case, please use the device carefully since the load current waveform becomes similar with rectangular waveform and this results may not make a device turn off.
● Degradation
In general, the emission of the IRED used in SSR will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least
twice the minimum required triggering current from initial operation.
● Standard Circuit
S102T02
S202T02
R1
+VCC
3
SSR
D1
4
V1
Load
2
ZS
AC Line
1
Tr1
ZS : Surge absorption circuit (Snubber circuit)
✩ For additional design assistance, please review our corresponding Optoelectronic Application Notes.
Sheet No.: D4-A01601EN
9
S102T02 Series
S202T02 Series
■ Manufacturing Guidelines
● Soldering Method
Flow Soldering (No solder bathing)
Flow soldering should be completed below 260˚C and within 10s.
Preheating is within the bounds of 100 to 150˚C and 30 to 80s.
Please solder within one time.
Other notices
Please test the soldering method in actual condition and make sure the soldering works fine, since the impact
on the junction between the device and PCB varies depending on the tooling and soldering conditions.
Sheet No.: D4-A01601EN
10
S102T02 Series
S202T02 Series
● Cleaning instructions
Solvent cleaning :
Solvent temperature should be 45˚C or below. Immersion time should be 3minutes or less.
Ultrasonic cleaning :
The impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time,
size of PCB and mounting method of the device.
Therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of
mass production.
Recommended solvent materials :
Ethyl alcohol, Methyl alcohol and Isopropyl alcohol.
In case the other type of solvent materials are intended to be used, please make sure they work fine in actual using conditions since some materials may erode the packaging resin.
● Presence of ODC
This product shall not contain the following materials.
And they are not used in the production process for this device.
Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform)
Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all.
Sheet No.: D4-A01601EN
11
S102T02 Series
S202T02 Series
■ Package specification
● Sleeve package
Package materials
Sleeve : HIPS
Stopper : Olefine-Elastomer
Package method
MAX. 25pcs of products shall be packaged in a sleeve.
Both ends shall be closed by stoppers.
MAX. 20 sleeves in one case.
±2
17.8
620
10.6
1.1
1.1
(30.0)
12.0
Sleeve outline dimensions
4.7
7.6
(8.5)
(Unit : mm)
Sheet No.: D4-A01601EN
12
S102T02 Series
S202T02 Series
■ Important Notices
with equipment that requires higher reliability such as:
--- Transportation control and safety equipment (i.e.,
aircraft, trains, automobiles, etc.)
--- Traffic signals
--- Gas leakage sensor breakers
--- Alarm equipment
--- Various safety devices, etc.
(iii) SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as:
--- Space applications
--- Telecommunication equipment [trunk lines]
--- Nuclear power control equipment
--- Medical and other life support equipment (e.g.,
scuba).
· The circuit application examples in this publication are
provided to explain representative applications of
SHARP devices and are not intended to guarantee any
circuit design or license any intellectual property rights.
SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices.
· Contact SHARP in order to obtain the latest device
specification sheets before using any SHARP device.
SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure,
and other contents described herein at any time without
notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice.
· If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is
necessary to obtain approval to export such SHARP devices.
· Observe the following points when using any devices
in this publication. SHARP takes no responsibility for
damage caused by improper use of the devices which
does not meet the conditions and absolute maximum
ratings to be used specified in the relevant specification
sheet nor meet the following conditions:
(i) The devices in this publication are designed for use
in general electronic equipment designs such as:
--- Personal computers
--- Office automation equipment
--- Telecommunication equipment [terminal]
--- Test and measurement equipment
--- Industrial control
--- Audio visual equipment
--- Consumer electronics
(ii) Measures such as fail-safe function and redundant
design should be taken to ensure reliability and safety
when SHARP devices are used for or in connection
· This publication is the proprietary product of SHARP
and is copyrighted, with all rights reserved. Under the
copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in
part, without the express written permission of SHARP.
Express written permission is also required before any
use of this publication may be made by a third party.
· Contact and consult with a SHARP representative if
there are any questions about the contents of this publication.
Sheet No.: D4-A01601EN
13