Revised September 2000 74F181 4-Bit Arithmetic Logic Unit General Description Features The 74F181 is a 4-bit Arithmetic logic Unit (ALU) which can perform all the possible 16 logic operations on two variables and a variety of arithmetic operations. It is 40% faster than the Schottky ALU and only consumes 30% as much power. ■ Full lookahead for high-speed arithmetic operation on long words Ordering Code: Order Number 74F181SC Package Number M24B Package Description 24-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300 Wide 74F181PC N24A 24-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-011, 0.600 Wide 74F181SPC N24C 24-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. Logic Symbols Connection Diagram Active-HIGH Operands Active-LOW Operands IEEE/IEC © 2000 Fairchild Semiconductor Corporation DS009491 www.fairchildsemi.com 74F181 4-Bit Arithmetic Logic Unit April 1988 74F181 Unit Loading/Fan Out Pin Names U.L. Input IIH/IIL HIGH/LOW Output IOH/IOL 1.0/3.0 20 µA/−1.8 mA Description A0–A3 A Operand Inputs (Active LOW) B0–B3 B Operand Inputs (Active LOW) 1.0/3.0 20 µA/−1.8 mA S0–S3 Function Select Inputs 1.0/4.0 20 µA/−2.4 mA M Mode Control Input 1.0/1.0 20 µA/−0.6 mA Cn Carry Input 1.0/5.0 20 µA/−3.0 mA 50/33.3 −1 mA/20 mA OC (Note 1)/33.3 (Note 1)/20 mA Carry Generate Output (Active LOW) 50/33.3 −1 mA/20 mA Carry Propagate Output (Active LOW) 50/33.3 −1 mA/20 mA Carry Output 50/33.3 −1 mA/20 mA F0–F3 Function Outputs (Active LOW) A=B Comparator Output G P Cn + 4 Note 1: OC-Open Collector Functional Description devices. Carry lookahead can be provided at various levels and offers high speed capability over extremely long word lengths. The 74F181 is a 4-bit high-speed parallel Arithmetic Logic Unit (ALU). Controlled by the four Function Select inputs (S0–S3) and the Mode Control input (M), it can perform all the 16 possible logic operations or 16 different arithmetic operations on Active HIGH or Active LOW operands. The Function Table lists these operations. The A = B output from the device goes HIGH when all four F outputs are HIGH and can be used to indicate logic equivalence over four bits when the unit is in the Subtract mode. The A = B output is open collector and can be wired AND with other A = B outputs to give a comparison for more than four bits. The A = B signal can also be used with the Cn+4 signal to indicate A > B and A < B. When the Mode Control input (M) is HIGH, all internal carries are inhibited and the device performs logic operations on the individual bits as listed. When the Mode Control input is LOW, the carries are enabled and the device performs arithmetic operations on the two 4-bit words. The device incorporates full internal carry lookahead and provides for either ripple carry between devices using the Cn + 4 output, or for carry lookahead between packages using the signals P (Carry Propagate) and G (Carry Generate). In the Add mode, P indicates that F is 15 or more, while G indicates that F is 16 or more. In the Subtract mode P indicates that F is zero or less, while G indicates that F is less than zero. P and G are not affected by carry in. When speed requirements are not stringent, the 74F181 can be used in a simple Ripple Carry mode by connecting the Carry output (Cn+4) signal to the Carry input (Cn) of the next unit. For high speed operation the device is used in conjunction with a carry lookahead circuit. One carry lookahead package is required for each group of four 74F181 www.fairchildsemi.com The Function Table lists the arithmetic operations that are performed without a carry in. An incoming carry adds a one to each operation. Thus, select code LHHL generates A minus B minus 1 (2s complement notation) without a carry in and generates A minus B when a carry is applied. Because subtraction is actually performed by complementary addition (1s complement), a carry out means borrow; thus a carry is generated when there is no underflow and no carry is generated when there is underflow. As indicated, this device can be used with either active LOW inputs producing active LOW outputs or with active HIGH inputs producing active HIGH outputs. For either case the table lists the operations that are performed to the operands labeled inside the logic symbol. 2 S0 a. All Input Data Inverted b. All Input Data True S1 S2 S3 Logic Arithmetic Arithmetic (M=H) (M=L, C0=Inactive) (M=L, C0=Active) L L L L A A minus 1 A H L L L A•B A • B minus 1 A•B A+B A • B minus 1 A•B L H L L H H L L L L H L H L H L L H H L H H H L Logic “1” minus 1 (2s comp.) A+B Zero A plus (A + B) A plus (A + B) plus 1 B A • B plus (A + B) A • B plus (A + B) plus 1 A⊕B A minus B minus 1 A minus B A+B A+B A + B plus 1 A plus (A + B plus 1 L L L H A•B A plus (A + B) H L L H A⊕ B A plus B A plus B plus 1 L H L H B A • B plus (A + B) A • B plus (A + B) plus 1 H H L H A+B A+B A + B plus 1 L L H H Logic “0” A plus A (2 × A) A plus A (2 × A) plus 1 H L H H A•B A plus A • B A plus A • B plus 1 L H H H A•B A plus A • B A plus A • B plus 1 H H H H A A A plus 1 L L L L A A A plus 1 H L L L A+B A+B A + B plus 1 L H L L A•B A+B A + B plus 1 H H L L L L H L Logic “0” minus 1 (2s comp.) A•B Zero A plus (A • B) A plus A • B plus 1 H L H L B A • B plus (A + B) A • B plus (A + B) plus 1 L H H L A⊕B A minus B minus 1 A minus B H H H L A•B A • B minus 1 A•B L L L H A+B A plus A • B A plus A • B plus 1 H L L H A⊕ B A plus B A plus B plus 1 L H L H B A • B plus (A + B) A • B plus (A + B) plus 1 H H L H A•B A • B minus 1 A•B L L H H Logic “1” A plus A (2 × A) A plus A (2 × A) plus 1 H L H H A+B A plus (A + B) A plus (A+B) plus 1 L H H H A+B A plus (A + B) A plus (A+B) plus 1 H H H H A A minus 1 A 3 www.fairchildsemi.com 74F181 Operation Table 74F181 Operation Table (Continued) S0 c. A All Input Data Inverted; B Input Data True d. A Input Data True; B Input Date Inverted www.fairchildsemi.com S1 S2 S3 Logic Arithmetic Arithmetic (M=H) (M=L, C0=Inactive) (M=L, C0=Active) L L L L A A minus 1 A H L L L A+B A • B minus 1 A•B A•B A • B minus 1 A•B L H L L H H L L L L H L H L H L H H H H L L Logic “1” minus 1 (2s comp.) Zero A•B A plus (A + B) A plus (A + B) plus 1 L B A • B plus (A + B) A • B plus (A + B) plus 1 L A⊕B A plus B A plus B plus 1 H L A+B A+B A + B plus 1 L H A+B A plus (A + B) A plus (A + B) plus 1 H L L H A⊕ B A minus B minus 1 A minus B L H L H B A • B plus (A + B) A • B plus (A + B) plus 1 H H L H A+B A+B A + B plus 1 L L H H Logic “0” A plus A (2 × A) A plus A (2 × A) plus 1 H L H H A•B A plus A • B A plus A • B plus 1 L H H H A•B A plus A • B A plus A • B plus 1 H H H H A A A plus 1 L L L L A A A plus 1 H L L L A•B A+B A + B plus 1 A+B A+B A + B plus 1 L H L L H H L L L L H L H L H L H H H H L L Logic “0” minus 1 (2s comp.) Zero A+B A plus A • B A plus A • B plus 1 L B A • B plus (A + B) A • B plus (A + B) plus 1 L A⊕B A plus B A plus B plus 1 H L A•B A • B minus 1 A•B L H A•B A plus A • B A plus A • B plus 1 H L L H A⊕ B A minus B minus 1 A minus B L H L H B A • B plus (A + B) A • B plus (A + B) plus 1 H H L H A•B A • B minus 1 A•B L L H H Logic “1” A plus A (2 × A) A plus A (2 × A) plus 1 H L H H A+B A plus (A + B) A plus (A+B) plus 1 L H H H A+B A plus (A + B) A plus (A+B) plus 1 H H H H A A minus 1 A 4 74F181 Logic Diagram p Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. 5 www.fairchildsemi.com 74F181 Absolute Maximum Ratings(Note 2) Recommended Operating Conditions Storage Temperature −65°C to +150 °C Ambient Temperature under Bias −55°C to +125 °C Free Air Ambient Temperature Junction Temperature under Bias −55°C to +150 °C Supply Voltage 0°C to +70°C +4.5V to +5.5V −0.5V to +7.0V VCC Pin Potential to Ground Pin Input Voltage (Note 3) −0.5V to +7.0V Input Current (Note 3) −30 mA to +5.0 mA Voltage Applied to Output in HIGH State (with VCC = 0V) Standard Output −0.5V to VCC 3-STATE Output −0.5V to +5.5V Note 2: Absolute maximum ratings are values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions is not implied. Current Applied to Output in LOW State (Max) Note 3: Either voltage limit or current limit is sufficient to protect inputs. twice the rated IOL (mA) ESD Last Passing Voltage (Min) 4000V DC Electrical Characteristics Symbol Parameter Min Typ Max Input HIGH Voltage VIL Input LOW Voltage 0.8 V VCD Input Clamp Diode Voltage −1.2 V VOH Output HIGH Voltage VOL Output LOW 2.0 Units VIH 10% VCC 2.5 5% VCC 2.7 10% VCC 0.5 Voltage IIH Input HIGH 5.0 Current IBVI Input HIGH Current 7.0 Breakdown Test ICEX Output HIGH 50 Leakage Current VID Input Leakage Test IOD 4.75 Output Leakage 3.75 Circuit Current IIL VCC V Recognized as a LOW Signal Min −1.8 Min V Min IOL = 20 mA µA Max VIN = 2.7V µA Max VIN = 7.0V µA Max VOUT = VCC (Fn, G, P, Cn+4) V 0.0 µA 0.0 IOHC Open Collector, Output −60 OFF Leakage Test IID = 1.9 µA All Other Pins Grounded VIOD = 150 mV All Other Pins Grounded VIN = 0.5V (M) VIN = 0.5V (A0, A1, A3, B0, B1, B3) Max −150 mA Max VOUT = 0V (Fn, G, P, Cn+4) 250 µA Min VO = VCC (A = B) −3.0 Output Short-Circuit Current IOH = −1 mA mA −2.4 IOS IIN = −18 mA IOH = −1 mA V −0.6 Input LOW Current Conditions Recognized as a HIGH Signal VIN = 0.5V (Sn, A2, B2) VIN = 0.5V (Cn) ICCH Power Supply Current 43 65.0 mA Max VO = HIGH ICCL Power Supply Current 43 65.0 mA Max VO = LOW www.fairchildsemi.com 6 74F181 AC Electrical Characteristics Symbol Parameter Path TA = −55°C to +125°C TA = 0°C to +70°C VCC = +5.0V VCC = +5.0V CL = 50 pF CL = 50 pF CL = 50 pF Min Typ Max Min Max Min Max tPLH Propagation Delay 3.0 6.4 8.5 3.0 10.0 3.0 9.5 tPHL Cn to Cn + 4 3.0 6.1 8.0 3.0 9.5 3.0 9.0 5.0 10.0 13.0 5.0 15.5 5.0 14.0 4.0 9.4 12.0 3.5 16.5 4.0 13.0 5.0 10.8 14.0 5.0 17.0 5.0 15.0 5.0 10.0 13.0 4.0 15.0 5.0 14.0 3.0 6.7 8.5 2.5 16.0 3.0 9.5 3.0 6.5 8.5 2.5 12.0 3.0 9.5 3.0 5.7 7.5 2.5 9.0 3.0 8.5 3.0 5.8 7.5 2.5 9.5 3.0 8.5 3.0 6.5 8.5 2.5 11.5 3.0 9.5 3.0 7.3 9.5 2.5 11.0 3.0 10.5 3.0 5.0 7.0 2.5 8.5 3.0 8.0 3.0 5.5 7.5 3.0 9.5 3.0 8.5 3.0 5.8 7.5 2.5 11.0 3.0 8.5 4.0 6.5 8.5 3.0 11.0 4.0 9.5 3.0 7.0 9.0 3.0 14.5 3.0 10.0 3.0 7.2 10.0 3.0 14.5 3.0 10.0 3.0 8.2 11.0 3.0 17.5 3.0 12.0 3.0 5.0 11.0 3.0 14.5 3.0 12.0 4.0 8.0 10.5 3.5 16.5 4.0 11.5 4.0 7.8 10.0 4.0 13.5 4.0 11.0 4.5 9.4 12.0 3.5 17.5 4.5 13.0 3.5 9.4 12.0 3.0 14.0 3.5 13.0 4.0 6.0 9.0 3.5 14.5 4.0 10.0 4.0 6.0 10.0 3.0 15.5 4.0 11.0 11.0 18.5 27.0 8.0 35.0 11.0 29.0 6.0 9.8 12.5 5.5 21.0 6.0 13.5 tPLH Propagation Delay tPHL A or B to Cn + 4 tPLH Propagation Delay tPHL A or B to Cn + 4 tPLH Propagation Delay tPHL Cn to F tPLH Propagation Delay tPHL A or B or G tPLH Propagation Delay tPHL A or B to G tPLH Propagation Delay tPHL A or B to P tPLH Propagation Delay tPHL A or B to P tPLH Propagation Delay tPHL Ai or Bi to Fi tPLH Propagation Delay tPHL Ai or Bi to Fi tPLH Propagation Delay tPHL Any A or B to Any F tPLH Propagation Delay tPHL Any A or B to Any F tPLH Propagation Delay tPHL A or B to F tPLH Propagation Delay tPHL A or B to A = B Mode TA = +25°C VCC = +5.0V Sum Dif Any Sum Dif Sum Dif Sum Dif Sum Dif Logic Dif 7 Units ns ns ns ns ns ns ns ns ns ns ns ns ns ns www.fairchildsemi.com 74F181 Physical Dimensions inches (millimeters) unless otherwise noted 24-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300 Wide Package Number M24B 24-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-011, 0.600 Wide Package Number N24A www.fairchildsemi.com 8 74F181 4-Bit Arithmetic Logic Unit Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 24-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300 Wide Package Number N24C Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 9 www.fairchildsemi.com