ISSI IS61VPD25636A

ISSI
IS61VPD25636A IS61LPD25636A
IS61VPD51218A IS61LPD51218A
256K x 36, 512K x 18
9 Mb SYNCHRONOUS PIPELINED,
DOUBLE CYCLE DESELECT STATIC RAM
FEATURES
• Internal self-timed write cycle
• Individual Byte Write Control and Global Write
• Clock controlled, registered address, data and
control
• Burst sequence control using MODE input
• Three chip enable option for simple depth
expansion and address pipelining
• Common data inputs and data outputs
• Auto Power-down during deselect
• Double cycle deselect
• Snooze MODE for reduced-power standby
• JTAG Boundary Scan for PBGA package
• Power Supply
LPD: VDD 3.3V + 5%, VDDQ 3.3V/2.5V + 5%
VPD: VDD 2.5V + 5%, VDDQ 2.5V + 5%
• JEDEC 100-Pin TQFP,
119-pin PBGA and 165-pin PBGA package
®
MAY 2005
DESCRIPTION
The ISSI IS61LPD/VPD25636A and IS61LPD/VPD51218A
are high-speed, low-power synchronous static RAMs designed to provide burstable, high-performance memory for
communication and networking applications. The IS61LPD/
VPD25636A is organized as 262,144 words by 36 bits, and
the IS61LPD/VPD51218A is organized as 524,288 words
by 18 bits. Fabricated with ISSI's advanced CMOS technology, the device integrates a 2-bit burst counter, high-speed
SRAM core, and high-drive capability outputs into a single
monolithic circuit. All synchronous inputs pass through
registers controlled by a positive-edge-triggered single
clock input.
Write cycles are internally self-timed and are initiated by the
rising edge of the clock input. Write cycles can be one to four
bytes wide as controlled by the write control inputs.
Separate byte enables allow individual bytes to be written.
The byte write operation is performed by using the byte
write enable (BWE) input combined with one or more
individual byte write signals (BWx). In addition, Global
Write (GW) is available for writing all bytes at one time,
regardless of the byte write controls.
Bursts can be initiated with either ADSP (Address Status
Processor) or ADSC (Address Status Cache Controller)
input pins. Subsequent burst addresses can be generated
internally and controlled by the ADV (burst address
advance) input pin.
The mode pin is used to select the burst sequence order,
Linear burst is achieved when this pin is tied LOW.
Interleave burst is achieved when this pin is tied HIGH or
left floating.
FAST ACCESS TIME
Symbol
tKQ
t KC
Parameter
Clock Access Time
Cycle Time
Frequency
250
2.6
4
250
200
3.1
5
200
Units
ns
ns
MHz
Copyright © 2005 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability
arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any
published information and before placing orders for products.
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
1
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
BLOCK DIAGRAM
MODE
Q0
CLK
CLK
A0
A0'
BINARY
COUNTER
CE
ADV
ADSC
ADSP
Q1
256Kx36;
512Kx18
MEMORY ARRAY
CLR
18/19
A
A1'
A1
16/17
D
18/19
Q
ADDRESS
REGISTER
CE
CLK
36,
or 18
GW
BWE
BW(a-d)
x18: a,b
x36: a-d
D
Q
DQ(a-d)
BYTE WRITE
REGISTERS
CLK
CE
CE2
CE2
36,
or 18
36,
or 18
2/4/8
D
Q
ENABLE
REGISTER
INPUT
REGISTERS
CLK
OUTPUT
REGISTERS
CLK
DQa - DQd
OE
CE
CLK
D
Q
ENABLE
DELAY
REGISTER
CLK
OE
2
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
ISSI
165-PIN BGA
119-PIN BGA
165-Ball, 13x15 mm BGA
1mm Ball Pitch, 11x15 Ball Array
119-Ball, 14x22 mm BGA
1mm Ball Pitch, 7x17 Ball Array
®
BOTTOM VIEW
BOTTOM VIEW
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
3
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
ISSI
®
119 BGA PACKAGE PIN CONFIGURATION-256K X 36 (TOP VIEW)
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
1
2
3
4
5
6
7
VDDQ
NC
NC
DQc
DQc
VDDQ
DQc
DQc
VDDQ
DQd
DQd
VDDQ
DQd
DQd
NC
NC
VDDQ
A
CE2
A
DQPc
DQc
DQc
DQc
DQc
VDD
DQd
DQd
DQd
DQd
DQPd
A
NC
TMS
A
A
A
Vss
Vss
Vss
BWc
Vss
NC
Vss
BWd
Vss
Vss
Vss
MODE
A
TDI
ADSP
ADSC
VDD
NC
CE
OE
ADV
GW
VDD
CLK
NC
BWE
A1*
A0*
VDD
A
TCK
A
A
A
Vss
Vss
Vss
BWb
Vss
NC
Vss
BWa
Vss
Vss
Vss
NC
A
TDO
A
A
A
DQPb
DQb
DQb
DQb
DQb
VDD
DQa
DQa
DQa
DQa
DQPa
A
NC
NC
VDDQ
NC
NC
DQb
DQb
VDDQ
DQb
DQb
VDDQ
DQa
DQa
VDDQ
DQa
DQa
NC
ZZ
VDDQ
Note: * A0 and A1 are the two least significant bits (LSB) of the address field and set the internal burst counter if burst is desired.
PIN DESCRIPTIONS
4
Symbol
A
Pin Name
Address Inputs
Symbol
OE
Pin Name
Output Enable
A0, A1
Synchronous Burst Address Inputs
ZZ
Power Sleep Mode
ADV
MODE
Burst Sequence Selection
ADSP
Synchronous Burst Address
Advance
Address Status Processor
TCK, TDO
JTAG Pins
ADSC
Address Status Controller
GW
Global Write Enable
CLK
Synchronous Clock
TMS, TDI
NC
No Connect
DQa-DQd
Data Inputs/Outputs
Output Power Supply
CE, CE2
Synchronous Chip Select
DQPa-Pd
BWx (x=a-d)
Synchronous Byte Write Controls
VDD
Power Supply
BWE
Byte Write Enable
VDDQ
Output Power Supply
Vss
Ground
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
ISSI
®
119 BGA PACKAGE PIN CONFIGURATION
512KX18 (TOP VIEW)
1
2
3
4
5
6
7
A
B
C
D
E
F
G
H
J
K
VDDQ
NC
NC
DQb
NC
VDDQ
NC
DQb
VDDQ
NC
A
CE2
A
NC
DQb
NC
DQb
NC
VDD
DQb
A
A
A
Vss
Vss
Vss
BWb
Vss
NC
Vss
ADSP
ADSC
VDD
NC
CE
OE
ADV
GW
VDD
CLK
A
A
A
Vss
Vss
Vss
Vss
Vss
NC
Vss
A
A
A
DQPa
NC
DQa
NC
DQa
VDD
NC
VDDQ
NC
NC
NC
DQa
VDDQ
DQa
NC
VDDQ
DQa
L
M
N
P
R
T
U
DQb
VDDQ
DQb
NC
NC
NC
VDDQ
NC
DQb
NC
DQPb
A
A
TMS
Vss
Vss
Vss
Vss
MODE
A
TDI
NC
BWE
A1*
A0*
VDD
NC
TCK
BWa
Vss
Vss
Vss
NC
A
TDO
DQa
NC
DQa
NC
A
A
NC
NC
VDDQ
NC
DQa
NC
ZZ
VDDQ
Note: * A0 and A1 are the two least significant bits (LSB) of the address field and set the internal burst counter if burst is
desired.
PIN DESCRIPTIONS
Symbol
A
Pin Name
Address Inputs
Symbol
OE
Pin Name
Output Enable
A0, A1
Synchronous Burst Address Inputs
ZZ
Power Sleep Mode
ADV
MODE
Burst Sequence Selection
ADSP
Synchronous Burst Address
Advance
Address Status Processor
TCK, TDO
JTAG Pins
ADSC
Address Status Controller
GW
Global Write Enable
CLK
Synchronous Clock
CE, CE2
Synchronous Chip Select
BWx (x=a,b)
Synchronous Byte Write Controls
BWE
Byte Write Enable
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
TMS, TDI
NC
No Connect
DQa-DQb
Data Inputs/Outputs
DQPa-Pb
Output Power Supply
VDD
Power Supply
VDDQ
Output Power Supply
Vss
Ground
5
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
165 PBGA PACKAGE PIN CONFIGURATION
256K X 36 (TOP VIEW)
1
2
3
4
5
6
7
8
9
10
11
A
NC
A
CE
BWc
BWb
CE2
BWE
ADSC
ADV
A
NC
B
NC
A
CE2
BWd
BWa
CLK
GW
OE
ADSP
A
NC
C
DQPc
NC
VDDQ
Vss
Vss
Vss
Vss
Vss
VDDQ
NC
D
DQc
DQc
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
DQb
DQb
E
DQc
DQc
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
DQb
DQb
F
DQc
DQc
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
DQb
DQb
G
DQc
DQc
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
DQb
DQb
H
NC
Vss
NC
VDD
Vss
Vss
Vss
VDD
NC
NC
ZZ
J
DQd
DQd
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
DQa
DQa
K
DQd
DQd
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
DQa
DQa
L
DQd
DQd
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
DQa
DQa
M
DQd
DQd
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
DQa
DQa
N
DQPd
NC
VDDQ
Vss
NC
NC
NC
Vss
VDDQ
NC
DQPa
P
NC
NC
A
A
TDI
A1 *
TDO
A
A
A
A
R
MODE
NC
A
A
TMS
A0 *
TCK
A
A
A
A
DQPb
Note: * A0 and A1 are the two least significant bits (LSB) of the address field and set the internal burst counter if burst is
desired.
PIN DESCRIPTIONS
Symbol
A
Pin Name
Address Inputs
Symbol
Pin Name
BWE
Byte Write Enable
A0, A1
Synchronous Burst Address Inputs
ADV
OE
Output Enable
ZZ
Power Sleep Mode
ADSP
Synchronous Burst Address
Advance
Address Status Processor
MODE
Burst Sequence Selection
ADSC
Address Status Controller
JTAG Pins
GW
Global Write Enable
CLK
Synchronous Clock
CE, CE2, CE2
Synchronous Chip Select
TCK, TDO
TMS, TDI
NC
DQx
DQPx
VDD
VDDQ
Vss
Ground
BWx (x=a,b,c,d) Synchronous Byte Write
Controls
6
No Connect
Data Inputs/Outputs
Data Inputs/Outputs
3.3V/2.5V Power Supply
Isolated Output Power Supply
3.3V/2.5V
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
165 PBGA PACKAGE PIN CONFIGURATION
512K X 18 (TOP VIEW)
1
2
3
4
5
6
7
8
9
10
11
A
NC
A
CE
BWb
NC
CE2
BWE
ADSC
ADV
A
A
B
NC
A
CE2
NC
BWa
CLK
GW
OE
ADSP
A
NC
C
NC
NC
VDDQ
Vss
Vss
Vss
Vss
Vss
VDDQ
NC
DQPa
D
NC
DQb
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
NC
DQa
E
NC
DQb
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
NC
DQa
F
NC
DQb
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
NC
DQa
G
NC
DQb
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
NC
DQa
H
NC
Vss
NC
VDD
Vss
Vss
Vss
VDD
NC
NC
ZZ
J
DQb
NC
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
DQa
NC
K
DQb
NC
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
DQa
NC
L
DQb
NC
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
DQa
NC
M
DQb
NC
VDDQ
VDD
Vss
Vss
Vss
VDD
VDDQ
DQa
NC
N
DQPb
NC
VDDQ
Vss
NC
NC
NC
Vss
VDDQ
NC
NC
P
NC
NC
A
A
TDI
A1 *
TDO
A
A
A
A
R
MODE
NC
A
A
TMS
A0 *
TCK
A
A
A
A
Note: * A0 and A1 are the two least significant bits (LSB) of the address field and set the internal burst counter if burst is
desired.
PIN DESCRIPTIONS
Symbol
A
Pin Name
Address Inputs
Symbol
BWE
Byte Write Enable
A0, A1
Synchronous Burst Address Inputs
ADV
OE
Output Enable
ZZ
Power Sleep Mode
ADSP
Synchronous Burst Address
Advance
Address Status Processor
MODE
Burst Sequence Selection
ADSC
Address Status Controller
JTAG Pins
GW
Global Write Enable
CLK
Synchronous Clock
CE, CE2, CE2
Synchronous Chip Select
BWx (x=a,b)
Synchronous Byte Write
Controls
TCK, TDO
TMS, TDI
NC
DQx
DQPx
VDD
VDDQ
Vss
Ground
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
Pin Name
No Connect
Data Inputs/Outputs
Data Inputs/Outputs
3.3V/2.5V Power Supply
Isolated Output Power Supply
3.3V/2.5V
7
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
ISSI
®
PIN CONFIGURATION
DQPc
DQPb
DQb
DQb
VDDQ
VSS
DQb
DQb
DQb
DQb
VSS
VDDQ
DQb
DQb
VSS
NC
VDD
ZZ
DQa
DQa
VDDQ
VSS
DQa
DQa
DQa
DQa
VSS
VDDQ
DQa
DQa
DQPa
DQPc
DQc
DQc
VDDQ
VSS
DQc
DQc
DQc
DQc
VSS
VDDQ
DQc
DQc
NC
VDD
NC
VSS
DQd
DQd
VDDQ
VSS
DQd
DQd
DQd
DQd
VSS
VDDQ
DQd
DQd
DQPd
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
1
80
79
2
78
3
77
4
76
5
75
6
74
7
73
8
72
9
71
10
70
11
69
12
68
13
67
14
66
15
65
16
64
17
63
18
62
19
61
20
60
21
59
22
58
23
57
24
56
25
55
26
54
27
53
28
52
29
51
30
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
DQPb
DQb
DQb
VDDQ
VSS
DQb
DQb
DQb
DQb
VSS
VDDQ
DQb
DQb
VSS
NC
VDD
ZZ
DQa
DQa
VDDQ
VSS
DQa
DQa
DQa
DQa
VSS
VDDQ
DQa
DQa
DQPa
MODE
A
A
A
A
A1
A0
NC
NC
VSS
VDD
NC
NC
A
A
A
A
A
A
A
MODE
A
A
A
A
A1
A0
NC
NC
VSS
VDD
NC
A
A
A
A
A
A
A
A
DQc
DQc
VDDQ
VSS
DQc
DQc
DQc
DQc
VSS
VDDQ
DQc
DQc
NC
VDD
NC
VSS
DQd
DQd
VDDQ
VSS
DQd
DQd
DQd
DQd
VSS
VDDQ
DQd
DQd
DQPd
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
1
80
2
79
3
78
4
77
5
76
6
75
7
74
73
8
72
9
71
10
70
11
69
12
68
13
67
14
66
15
65
16
64
17
63
18
62
19
61
20
60
21
59
22
58
23
57
24
56
25
55
26
54
27
53
28
52
29
51
30
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
A
A
CE
CE2
BWd
BWc
BWb
BWa
A
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
A
A
CE
CE2
BWd
BWc
BWb
BWa
CE2
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
100-PIN TQFP (256K X 36)
(2 Chip-Enable option)
(3 Chip-Enable option)
PIN DESCRIPTIONS
A0, A1
Synchronous Address Inputs. These
pins must tied to the two LSBs of the
address bus.
DQa-DQd
Synchronous Data Input/Output
DQPa-DQPd
Parity Data Input/Output
GW
Synchronous Global Write Enable
A
Synchronous Address Inputs
ADSC
Synchronous Controller Address
Status
MODE
Burst Sequence Mode Selection
OE
Output Enable
ADSP
Synchronous Processor Address
Status
VDD
3.3V/2.5V Power Supply
ADV
VDDQ
Synchronous Burst Address Advance
Isolated Output Buffer Supply:
3.3V/2.5V
BWa-BWd
Synchronous Byte Write Enable
Vss
Ground
BWE
Synchronous Byte Write Enable
ZZ
Snooze Enable
CE, CE2, CE2 Synchronous Chip Enable
CLK
8
Synchronous Clock
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
ISSI
®
PIN CONFIGURATION
A
NC
NC
VDDQ
VSS
NC
DQPa
DQa
DQa
VSS
VDDQ
DQa
DQa
VSS
NC
VDD
ZZ
DQa
DQa
VDDQ
VSS
DQa
DQa
NC
NC
VSS
VDDQ
NC
NC
NC
NC
NC
NC
VDDQ
VSS
NC
NC
DQb
DQb
VSS
VDDQ
DQb
DQb
NC
VDD
NC
VSS
DQb
DQb
VDDQ
VSS
DQb
DQb
DQPb
NC
VSS
VDDQ
NC
NC
NC
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
1
80
2
79
3
78
4
77
5
76
6
75
7
74
8
73
9
72
10
71
11
70
12
69
13
68
14
67
15
66
16
65
17
64
18
63
19
62
20
61
21
60
22
59
23
58
24
57
25
56
26
55
27
54
28
53
29
52
30
51
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
A
NC
NC
VDDQ
VSS
NC
DQPa
DQa
DQa
VSS
VDDQ
DQa
DQa
VSS
NC
VDD
ZZ
DQa
DQa
VDDQ
VSS
DQa
DQa
NC
NC
VSS
VDDQ
NC
NC
NC
MODE
A
A
A
A
A1
A0
NC
NC
VSS
VDD
NC
NC
A
A
A
A
A
A
A
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
80
1
79
2
78
3
77
4
76
5
75
6
74
7
73
8
72
9
71
10
70
11
69
12
13
68
14
67
15
66
16
65
17
64
18
63
19
62
20
61
21
60
22
59
23
58
24
57
25
56
26
55
27
54
28
53
29
52
30
51
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
MODE
A
A
A
A
A1
A0
NC
NC
VSS
VDD
NC
A
A
A
A
A
A
A
A
NC
NC
NC
VDDQ
VSS
NC
NC
DQb
DQb
VSS
VDDQ
DQb
DQb
NC
VDD
NC
VSS
DQb
DQb
VDDQ
VSS
DQb
DQb
DQPb
NC
VSS
VDDQ
NC
NC
NC
A
A
CE
CE2
NC
NC
BWb
BWa
A
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
A
A
CE
CE2
NC
NC
BWb
BWa
CE2
VDD
VSS
CLK
GW
BWE
OE
ADSC
ADSP
ADV
A
A
100-PIN TQFP (512K X 18)
(3 Chip-Enable Option)
(2 Chip-Enable Option)
PIN DESCRIPTIONS
A0, A1
Synchronous Address Inputs. These
pins must tied to the two LSBs of the
address bus.
A
Synchronous Address Inputs
ADSC
Synchronous Controller Address
Status
ADSP
Synchronous Processor Address
Status
DQPa-DQPb
Parity Data I/O; DQPa is parity for
DQa1-8; DQPb is parity for DQb1-8
GW
Synchronous Global Write Enable
MODE
Burst Sequence Mode Selection
OE
Output Enable
VDD
3.3V/2.5V Power Supply
VDDQ
Isolated Output Buffer Supply:
3.3V/2.5V
ADV
Synchronous Burst Address Advance
BWa-BWb
Synchronous Byte Write Enable
Vss
Ground
BWE
Synchronous Byte Write Enable
ZZ
Snooze Enable
CE, CE2, CE2 Synchronous Chip Enable
CLK
Synchronous Clock
DQa-DQb
Synchronous Data Input/Output
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
9
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
TRUTH TABLE(1-8)
ADDRESS
CE
Deselect Cycle, Power-Down
None
H
X
X
L
X
L
X
X
Deselect Cycle, Power-Down
None
L
X
L
L
L
X
X
Deselect Cycle, Power-Down
None
L
H
X
L
L
X
Deselect Cycle, Power-Down
None
L
X
L
L
H
Deselect Cycle, Power-Down
None
L
H
X
L
Snooze Mode, Power-Down
None
X
X
X
Read Cycle, Begin Burst
External
L
L
Read Cycle, Begin Burst
External
L
Write Cycle, Begin Burst
External
Read Cycle, Begin Burst
Read Cycle, Begin Burst
OPERATION
CE2 CE2
ZZ
ADSP ADSC ADV
WRITE OE
CLK
DQ
X
L-H
High-Z
X
X
L-H
High-Z
X
X
X
L-H
High-Z
L
X
X
X
L-H
High-Z
H
L
X
X
X
L-H
High-Z
H
X
X
X
X
X
X
High-Z
H
L
L
X
X
X
L
L-H
Q
L
H
L
L
X
X
X
H
L-H
High-Z
L
L
H
L
H
L
X
L
X
L-H
D
External
L
L
H
L
H
L
X
H
L
L-H
Q
External
L
L
H
L
H
L
X
H
H
L-H
High-Z
Read Cycle, Continue Burst
Next
X
X
X
L
H
H
L
H
L
L-H
Q
Read Cycle, Continue Burst
Next
X
X
X
L
H
H
L
H
H
L-H
High-Z
Read Cycle, Continue Burst
Next
H
X
X
L
X
H
L
H
L
L-H
Q
Read Cycle, Continue Burst
Next
H
X
X
L
X
H
L
H
H
L-H
High-Z
Write Cycle, Continue Burst
Next
X
X
X
L
H
H
L
L
X
L-H
D
Write Cycle, Continue Burst
Next
H
X
X
L
X
H
L
L
X
L-H
D
Read Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
H
L
L-H
Q
Read Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
H
H
L-H
High-Z
Read Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
H
L
L-H
Q
Read Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
H
H
L-H
High-Z
Write Cycle, Suspend Burst
Current
X
X
X
L
H
H
H
L
X
L-H
D
Write Cycle, Suspend Burst
Current
H
X
X
L
X
H
H
L
X
L-H
D
NOTE:
1. X means “Don’t Care.” H means logic HIGH. L means logic LOW.
2. For WRITE, L means one or more byte write enable signals (BWa-d) and BWE are LOW or GW is LOW. WRITE = H for all
BWx, BWE, GW HIGH.
3. BWa enables WRITEs to DQa’s and DQPa. BWb enables WRITEs to DQb’s and DQPb. BWc enables WRITEs to DQc’s and
DQPc. BWd enables WRITEs to DQd’s and DQPd. DQPa and DQPb are available on the x18 version. DQPa-DQPd are
available on the x36 version.
4. All inputs except OE and ZZ must meet setup and hold times around the rising edge (LOW to HIGH) of CLK.
5. Wait states are inserted by suspending burst.
6. For a WRITE operation following a READ operation, OE must be HIGH before the input data setup time and held HIGH during
the input data hold time.
7. This device contains circuitry that will ensure the outputs will be in High-Z during power-up.
8. ADSP LOW always initiates an internal READ at the L-H edge of CLK. A WRITE is performed by setting one or more byte
write enable signals and BWE LOW or GW LOW for the subsequent L-H edge of CLK. See WRITE timing diagram for
clarification.
PARTIAL TRUTH TABLE
Function
Read
Read
Write Byte 1
Write All Bytes
Write All Bytes
10
GW
BWE
BWa
BWb
BWc
BWd
H
H
H
H
L
H
L
L
L
X
X
H
L
L
X
X
H
H
L
X
X
H
H
L
X
X
H
H
L
X
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
ISSI
®
INTERLEAVED BURST ADDRESS TABLE (MODE = VDD or No Connect)
External Address
A1 A0
1st Burst Address
A1 A0
2nd Burst Address
A1 A0
3rd Burst Address
A1 A0
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
LINEAR BURST ADDRESS TABLE (MODE = VSS)
0,0
A1', A0' = 1,1
0,1
1,0
ABSOLUTE MAXIMUM RATINGS(1)
Symbol
TSTG
PD
IOUT
VIN, VOUT
VIN
Parameter
Storage Temperature
Power Dissipation
Output Current (per I/O)
Voltage Relative to Vss for I/O Pins
Voltage Relative to Vss for
for Address and Control Inputs
VDD
Voltage on VDD Supply Relative to Vss
Value
Unit
–55 to +150
°C
1.6
W
100
mA
–0.5 to VDDQ + 0.5
V
–0.5 to VDD + 0.5
V
–0.5 to 4.6
V
Notes:
1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at
these or any other conditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended
periods may affect reliability.
2. This device contains circuity to protect the inputs against damage due to high static voltages or
electric fields; however, precautions may be taken to avoid application of any voltage higher than
maximum rated voltages to this high-impedance circuit.
3. This device contains circuitry that will ensure the output devices are in High-Z at power up.
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
11
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
OPERATING RANGE (IS61LPDXXXXX)
Range
Commercial
Ambient Temperature
0°C to +70°C
VDD
3.3V + 5%
VDDQ
3.3 / 2.5V + 5%
–40°C to +85°C
3.3V + 5%
3.3 / 2.5V + 5%
Ambient Temperature
0°C to +70°C
VDD
2.5V + 5%
VDDQ
2.5V + 5%
–40°C to +85°C
2.5V + 5%
2.5V + 5%
Industrial
OPERATING RANGE (IS61VPDXXXXX)
Range
Commercial
Industrial
DC ELECTRICAL CHARACTERISTICS (Over Operating Range)
3.3V
Symbol
Parameter
Test Conditions
VOH
Output HIGH Voltage
VOL
Output LOW Voltage
VIH
Input HIGH Voltage
VIL
Input LOW Voltage
2.5V
Min.
Max.
Min.
Max.
IOH = –4.0 mA (3.3V)
IOH = –1.0 mA (2.5V)
2.4
—
2.0
—
V
IOL = 8.0 mA (3.3V)
IOL = 1.0 mA (2.5V)
—
0.4
—
0.4
V
2.0
VDD + 0.3
1.7
VDD + 0.3
V
-0.3
0.8
-0.3
0.7
V
-5
5
-5
5
µA
-5
5
-5
5
µA
Vss ≤ VIN ≤ VDD
(1)
ILI
Input Leakage Current
ILO
Output Leakage Current Vss ≤ VOUT ≤ VDDQ,
OE = VIH
Unit
POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range)
-250
MAX
x18
x36
-200
MAX
x18
x36
Device Selected,
Com.
OE = VIH, ZZ ≤ VIL,
IND.
All Inputs ≤ 0.2V or ≥ VDD – 0.2V,
Cycle Time ≥ tKC min.
275
300
275
300
250
275
250
275
mA
Standby Current
TTL Input
Device Deselected,
VDD = Max.,
All Inputs ≤ VIL or ≥ VIH,
ZZ ≤ VIL, f = Max.
COM.
Ind.
150
150
150
150
150
150
150
150
mA
ISBI
Standby Current
CMOS Input
Device Deselected,
Com.
VDD = Max.,
Ind.
VIN ≤ VSS + 0.2V or ≥VDD – 0.2V
f=0
100
105
100
105
100
105
100
105
mA
ISB2
Sleep Mode
ZZ>VIH
50
60
50
60
50
60
50
60
mA
Symbol Parameter
Test Conditions
ICC
AC Operating
Supply Current
ISB
Temp. range
Com.
Ind.
Unit
Note:
1. MODE pin has an internal pullup and should be tied to VDD or VSS. It exhibits ±100µA maximum leakage current when tied to ≤
VSS + 0.2V or ≥ VDD – 0.2V.
12
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
CAPACITANCE(1,2)
Symbol
Parameter
CIN
Input Capacitance
COUT
Input/Output Capacitance
Conditions
Max.
Unit
VIN = 0V
6
pF
VOUT = 0V
8
pF
Notes:
1. Tested initially and after any design or process changes that may affect these parameters.
2. Test conditions: TA = 25°C, f = 1 MHz, VDD = 3.3V.
3.3V I/O AC TEST CONDITIONS
Parameter
Input Pulse Level
Input Rise and Fall Times
Input and Output Timing
and Reference Level
Output Load
Unit
0V to 3.0V
1.5 ns
1.5V
See Figures 1 and 2
AC TEST LOADS
317 Ω
3.3V
ZO = 50Ω
Output
Buffer
50Ω
1.5V
Figure 1
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
OUTPUT
5 pF
Including
jig and
scope
351 Ω
Figure 2
13
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
ISSI
®
2.5V I/O AC TEST CONDITIONS
Parameter
Input Pulse Level
Input Rise and Fall Times
Input and Output Timing
and Reference Level
Output Load
Unit
0V to 2.5V
1.5 ns
1.25V
See Figures 3 and 4
2.5 I/O OUTPUT LOAD EQUIVALENT
1,667 Ω
2.5V
ZO = 50Ω
Output
50Ω
1.25V
Figure 3
14
OUTPUT
5 pF
Including
jig and
scope
1,538 Ω
Figure 4
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
READ/WRITE CYCLE SWITCHING CHARACTERISTICS (Over Operating Range)
-250
Symbol
Parameter
Min.
Max.
-200
Min.
Max.
Unit
fMAX
Clock Frequency
—
250
—
200
MHz
tKC
Cycle Time
4.0
—
5
—
ns
tKH
Clock High Time
1.7
—
2
—
ns
tKL
Clock Low Time
1.7
—
2
—
ns
Clock Access Time
—
2.6
—
3.1
ns
tKQ
(2)
tKQX
Clock High to Output Invalid
0.8
—
1.5
—
ns
(2,3)
tKQLZ
Clock High to Output Low-Z
0.8
—
1
—
ns
tKQHZ(2,3)
Clock High to Output High-Z
—
2.6
—
3.0
ns
tOEQ
Output Enable to Output Valid
—
2.6
—
3.1
ns
(2,3)
Output Enable to Output Low-Z
0
—
0
—
ns
(2,3)
tOEHZ
Output Disable to Output High-Z
—
2.6
—
3.0
ns
tAS
Address Setup Time
1.2
—
1.4
—
ns
tWS
Read/Write Setup Time
1.2
—
1.4
—
ns
tCES
Chip Enable Setup Time
1.2
—
1.4
—
ns
tAVS
Address Advance Setup Time
1.2
—
1.4
—
ns
tDS
Data Setup Time
1.2
—
1.4
—
ns
tAH
Address Hold Time
0.3
—
0.4
—
ns
tWH
Write Hold Time
0.3
—
0.4
—
ns
tCEH
Chip Enable Hold Time
0.3
—
0.4
—
ns
tAVH
Address Advance Hold Time
0.3
—
0.4
—
ns
tDH
Data Hold Time
0.3
—
0.4
—
ns
tPDS
ZZ High to Power Down
—
2
—
2
cyc
tPUS
ZZ Low to Power Down
—
2
—
2
cyc
tOELZ
Note:
1. Configuration signal MODE is static and must not change during normal operation.
2. Guaranteed but not 100% tested. This parameter is periodically sampled.
3. Tested with load in Figure 2.
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
15
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
READ/WRITE CYCLE TIMING
tKC
CLK
tSS
tSH
tKH
tKL
ADSP is blocked by CE inactive
ADSP
tSS
tSH
ADSC initiate read
ADSC
tAVH
tAVS
Suspend Burst
ADV
tAS
Address
tAH
RD1
RD3
RD2
tWS
tWH
tWS
tWH
GW
BWE
BWx
tCES
tCEH
tCES
tCEH
tCES
tCEH
CE Masks ADSP
CE
Unselected with CE2
CE2 and CE2 only sampled with ADSP or ADSC
CE2
CE2
tOEHZ
tOEQ
OE
DATAOUT
tKQX
tOEQX
tOELZ
High-Z
1a
2a
2b
2c
2d
tKQLZ
3a
tKQHZ
tKQ
DATAIN
High-Z
Pipelined Read
Single Read
16
Burst Read
Unselected
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
ISSI
®
WRITE CYCLE TIMING
tKC
CLK
tSS
tSH
tKH
tKL
ADSP is blocked by CE inactive
ADSP
ADSC initiate Write
ADSC
tAVH
ADV must be inactive for ADSP Write tAVS
ADV
tAS
Address
tAH
WR1
WR3
WR2
tWS
tWH
tWS
tWH
tWS
tWH
GW
BWE
BWx
WR1
tCES
tCEH
tCES
tCEH
tCES
tCEH
tWS
tWH
WR2
WR3
CE Masks ADSP
CE
Unselected with CE2
CE2 and CE2 only sampled with ADSP or ADSC
CE2
CE2
OE
DATAOUT
High-Z
tDS
DATAIN
High-Z
Single Write
tDH
1a
BW4-BW1 only are applied to first cycle of WR2
2a
2b
Burst Write
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
2c
2d
3a
Write
Unselected
17
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
SNOOZE MODE ELECTRICAL CHARACTERISTICS
Symbol
Parameter
Conditions
Min.
Max.
Unit
ISB2
Current during SNOOZE MODE
ZZ ≥ Vih
—
60
mA
tPDS
ZZ active to input ignored
—
2
cycle
tPUS
ZZ inactive to input sampled
2
—
cycle
tZZI
ZZ active to SNOOZE current
—
2
cycle
tRZZI
ZZ inactive to exit SNOOZE current
0
—
ns
SNOOZE MODE TIMING
CLK
tPDS
ZZ setup cycle
tPUS
ZZ recovery cycle
ZZ
tZZI
Isupply
ISB2
tRZZI
All Inputs
(except ZZ)
Deselect or Read Only
Deselect or Read Only
Normal
operation
cycle
Outputs
(Q)
High-Z
Don't Care
18
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
ISSI
®
IEEE 1149.1 SERIAL BOUNDARY SCAN (JTAG)
TEST ACCESS PORT (TAP) - TEST CLOCK
The IS61LPD/VPD25636A and IS61LPD/VPD51218A have
a serial boundary scan Test Access Port (TAP) in the PBGA
package only. (The TQFP package not available.) This port
operates in accordance with IEEE Standard 1149.1-1900,
but does not include all functions required for full 1149.1
compliance. These functions from the IEEE specification are
excluded because they place added delay in the critical
speed path of the SRAM. The TAP controller operates in a
manner that does not conflict with the performance of other
devices using 1149.1 fully compliant TAPs. The TAP
operates using JEDEC standard 2.5V I/O logic levels.
The test clock is only used with the TAP controller. All
inputs are captured on the rising edge of TCK and outputs
are driven from the falling edge of TCK.
DISABLING THE JTAG FEATURE
The SRAM can operate without using the JTAG feature. To
disable the TAP controller, TCK must be tied LOW (Vss) to
prevent clocking of the device. TDI and TMS are internally
pulled up and may be disconnected. They may alternately
be connected to VDD through a pull-up resistor. TDO should
be left disconnected. On power-up, the device will start in a
reset state which will not interfere with the device operation.
TEST MODE SELECT (TMS)
The TMS input is used to send commands to the TAP
controller and is sampled on the rising edge of TCK. This
pin may be left disconnected if the TAP is not used. The
pin is internally pulled up, resulting in a logic HIGH level.
TEST DATA-IN (TDI)
The TDI pin is used to serially input information to the
registers and can be connected to the input of any
register. The register between TDI and TDO is chosen by
the instruction loaded into the TAP instruction register.
For information on instruction register loading, see the
TAP Controller State Diagram. TDI is internally pulled up
and can be disconnected if the TAP is unused in an
application. TDI is connected to the Most Significant Bit
(MSB) on any register.
TAP CONTROLLER BLOCK DIAGRAM
0
Bypass Register
2
1
0
Instruction Register
TDI
Selection Circuitry
Selection Circuitry
31 30 29
. . .
2
1
0
2
1
0
TDO
Identification Register
x
. . . . .
Boundary Scan Register*
TCK
TMS
TAP CONTROLLER
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
19
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
TEST DATA OUT (TDO)
The TDO output pin is used to serially clock data-out from
the registers. The output is active depending on the current
state of the TAP state machine (see TAP Controller State
Diagram). The output changes on the falling edge of TCK
and TDO is connected to the Least Significant Bit (LSB) of
any register.
PERFORMING A TAP RESET
A Reset is performed by forcing TMS HIGH (VDD) for five
rising edges of TCK. RESET may be performed while the
SRAM is operating and does not affect its operation. At
power-up, the TAP is internally reset to ensure that TDO
comes up in a high-Z state.
TAP REGISTERS
Registers are connected between the TDI and TDO pins
and allow data to be scanned into and out of the SRAM test
circuitry. Only one register can be selected at a time
through the instruction registers. Data is serially loaded
into the TDI pin on the rising edge of TCK and output on the
TDO pin on the falling edge of TCK.
Instruction Register
Three-bit instructions can be serially loaded into the
instruction register. This register is loaded when it is
placed between the TDI and TDO pins. (See TAP Controller
Block Diagram) At power-up, the instruction register is
loaded with the IDCODE instruction. It is also loaded with
the IDCODE instruction if the controller is placed in a reset
state as previously described.
When the TAP controller is in the CaptureIR state, the two
least significant bits are loaded with a binary “01” pattern
to allow for fault isolation of the board level serial test path.
Bypass Register
To save time when serially shifting data through registers,
it is sometimes advantageous to skip certain states. The
bypass register is a single-bit register that can be placed
between TDI and TDO pins. This allows data to be shifted
through the SRAM with minimal delay. The bypass register
®
is set LOW (Vss) when the BYPASS instruction is executed.
Boundary Scan Register
The boundary scan register is connected to all input and
output pins on the SRAM. Several no connect (NC) pins are
also included in the scan register to reserve pins for higher
density devices. The x36 configuration has a 75-bit-long
register and the x18 configuration also has a 75-bit-long
register. The boundary scan register is loaded with the
contents of the RAM Input and Output ring when the TAP
controller is in the Capture-DR state and then placed
between the TDI and TDO pins when the controller is moved
to the Shift-DR state. The EXTEST, SAMPLE/PRELOAD
and SAMPLE-Z instructions can be used to capture the
contents of the Input and Output ring.
The Boundary Scan Order tables show the order in which the
bits are connected. Each bit corresponds to one of the
bumps on the SRAM package. The MSB of the register is
connected to TDI, and the LSB is connected to TDO.
Scan Register Sizes
Register Name
Bit Size (x18)
Bit Size (x36)
Instruction
3
3
Bypass
1
1
ID
32
32
Boundary Scan
75
75
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit
code during the Capture-DR state when the IDCODE
command is loaded to the instruction register. The IDCODE
is hardwired into the SRAM and can be shifted out when
the TAP controller is in the Shift-DR state. The ID register
has vendor code and other information described in the
Identification Register Definitions table.
IDENTIFICATION REGISTER DEFINITIONS
Instruction Field
Description
256K x 36
512K x 18
Revision Number (31:28)
Reserved for version number.
xxxx
xxxx
Device Depth (27:23)
Defines depth of SRAM. 256K or 512K
00111
01000
Device Width (22:18)
Defines with of the SRAM. x36 or x18
00100
00011
ISSI Device ID (17:12)
Reserved for future use.
xxxxx
xxxxx
ISSI JEDEC ID (11:1)
Allows unique identification of SRAM vendor.
00011010101
00011010101
ID Register Presence (0)
Indicate the presence of an ID register.
1
1
20
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
ISSI
®
TAP INSTRUCTION SET
SAMPLE/PRELOAD
Eight instructions are possible with the three-bit instruction
register and all combinations are listed in the Instruction
Code table. Three instructions are listed as RESERVED
and should not be used and the other five instructions are
described below. The TAP controller used in this SRAM is
not fully compliant with the 1149.1 convention because
some mandatory instructions are not fully implemented.
The TAP controller cannot be used to load address, data or
control signals and cannot preload the Input or Output
buffers. The SRAM does not implement the 1149.1 commands EXTEST or INTEST or the PRELOAD portion of
SAMPLE/PRELOAD; instead it performs a capture of the
Inputs and Output ring when these instructions are executed.
Instructions are loaded into the TAP controller during the
Shift-IR state when the instruction register is placed
between TDI and TDO. During this state, instructions are
shifted from the instruction register through the TDI and
TDO pins. To execute an instruction once it is shifted in,
the TAP controller must be moved into the Update-IR
state.
SAMPLE/PRELOAD is a 1149.1 mandatory instruction.
The PRELOAD portion of this instruction is not implemented, so the TAP controller is not fully 1149.1 compliant. When the SAMPLE/PRELOAD instruction is loaded
to the instruction register and the TAP controller is in the
Capture-DR state, a snapshot of data on the inputs and
output pins is captured in the boundary scan register.
It is important to realize that the TAP controller clock
operates at a frequency up to 10 MHz, while the SRAM
clock runs more than an order of magnitude faster.
Because of the clock frequency differences, it is possible
that during the Capture-DR state, an input or output will
under-go a transition. The TAP may attempt a signal
capture while in transition (metastable state). The device
will not be harmed, but there is no guarantee of the value
that will be captured or repeatable results.
To guarantee that the boundary scan register will capture
the correct signal value, the SRAM signal must be
stabilized long enough to meet the TAP controller’s
capture set-up plus hold times (tCS and tCH). To insure that
the SRAM clock input is captured correctly, designs need
a way to stop (or slow) the clock during a SAMPLE/
PRELOAD instruction. If this is not an issue, it is possible
to capture all other signals and simply ignore the value of
the CLK and CLK captured in the boundary scan register.
Once the data is captured, it is possible to shift out the data
by putting the TAP into the Shift-DR state. This places the
boundary scan register between the TDI and TDO pins.
Note that since the PRELOAD part of the command is not
implemented, putting the TAP into the Update to the Update-DR
state while performing a SAMPLE/PRELOAD instruction
will have the same effect as the Pause-DR command.
EXTEST
EXTEST is a mandatory 1149.1 instruction which is to be
executed whenever the instruction register is loaded with
all 0s. Because EXTEST is not implemented in the TAP
controller, this device is not 1149.1 standard compliant.
The TAP controller recognizes an all-0 instruction. When
an EXTEST instruction is loaded into the instruction
register, the SRAM responds as if a SAMPLE/PRELOAD
instruction has been loaded. There is a difference between
the instructions, unlike the SAMPLE/PRELOAD instruction,
EXTEST places the SRAM outputs in a High-Z state.
IDCODE
The IDCODE instruction causes a vendor-specific, 32-bit
code to be loaded into the instruction register. It also
places the instruction register between the TDI and TDO
pins and allows the IDCODE to be shifted out of the device
when the TAP controller enters the Shift-DR state. The
IDCODE instruction is loaded into the instruction register
upon power-up or whenever the TAP controller is given a
test logic reset state.
SAMPLE-Z
The SAMPLE-Z instruction causes the boundary scan
register to be connected between the TDI and TDO pins
when the TAP controller is in a Shift-DR state. It also
places all SRAM outputs into a High-Z state.
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
BYPASS
When the BYPASS instruction is loaded in the instruction
register and the TAP is placed in a Shift-DR state, the
bypass register is placed between the TDI and TDO pins.
The advantage of the BYPASS instruction is that it
shortens the boundary scan path when multiple devices
are connected together on a board.
RESERVED
These instructions are not implemented but are reserved
for future use. Do not use these instructions.
21
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
INSTRUCTION CODES
Code
Instruction
Description
000
EXTEST
Captures the Input/Output ring contents. Places the boundary scan register
between the TDI and TDO. Forces all SRAM outputs to High-Z state. This
instruction is not 1149.1 compliant.
001
IDCODE
Loads the ID register with the vendor ID code and places the register between
TDI and TDO. This operation does not affect SRAM operation.
010
SAMPLE-Z
Captures the Input/Output contents. Places the boundary scan register between TDI
and TDO. Forces all SRAM output drivers to a High-Z state.
011
RESERVED
Do Not Use: This instruction is reserved for future use.
100
SAMPLE/PRELOAD
101
RESERVED
Do Not Use: This instruction is reserved for future use.
110
RESERVED
Do Not Use: This instruction is reserved for future use.
111
BYPASS
Captures the Input/Output ring contents. Places the boundary scan register between
TDI and TDO. Does not affect the SRAM operation. This instruction does not
implement 1149.1 preload function and is therefore not 1149.1 compliant.
Places the bypass register between TDI and TDO. This operation does not
affect SRAM operation.
TAP CONTROLLER STATE DIAGRAM
Test Logic Reset
1
0
Run Test/Idle
1
Select DR
0
0
1
1
1
Capture DR
0
Shift DR
1
Exit1 DR
0
Select IR
0
1
Exit1 IR
0
Pause DR
0
1
0
1
22
Exit2 DR
1
Update DR
0
Capture IR
0
Shift IR
1
0
Pause IR
1
0
1
1
0
1
0
Exit2 IR
1
Update IR
0
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
TAP Electrical Characteristics Over the Operating Range(1,2)
Symbol
Parameter
Test Conditions
Min.
Max.
Units
VOH1
Output HIGH Voltage
IOH = –2.0 mA
1.7
—
V
VOH2
Output HIGH Voltage
IOH = –100 µA
2.1
—
V
VOL1
Output LOW Voltage
IOL = 2.0 mA
—
0.7
V
VOL2
Output LOW Voltage
IOL = 100 µA
—
0.2
V
VIH
Input HIGH Voltage
1.7
VDD +0.3
V
VIL
Input LOW Voltage
–0.3
0.7
V
IX
Input Load Current
–5
5
mA
Vss ≤ V I ≤ VDDQ
Notes:
1. All Voltage referenced to Ground.
2. Overshoot: VIH (AC) ≤ VDD +1.5V for t ≤ tTCYC/2,
Undershoot:VIL (AC) ≤ 0.5V for t ≤ tTCYC/2,
Power-up: VIH < 2.6V and VDD < 2.4V and VDDQ < 1.4V for t < 200 ms.
TAP AC ELECTRICAL CHARACTERISTICS(1,2) (OVER OPERATING RANGE)
Symbol Parameter
Min.
Max.
Unit
tTCYC
TCK Clock cycle time
100
—
ns
fTF
TCK Clock frequency
—
10
MHz
tTH
TCK Clock HIGH
40
—
ns
tTL
TCK Clock LOW
40
—
ns
tTMSS
TMS setup to TCK Clock Rise
10
—
ns
tTDIS
TDI setup to TCK Clock Rise
10
—
ns
t CS
Capture setup to TCK Rise
10
—
ns
tTMSH
TMS hold after TCK Clock Rise
10
—
ns
tTDIH
TDI Hold after Clock Rise
10
—
ns
t CH
Capture hold after Clock Rise
10
—
ns
tTDOV
TCK LOW to TDO valid
—
20
ns
tTDOX
TCK LOW to TDO invalid
0
—
ns
Notes:
1. Both tCS and tCH refer to the set-up and hold time latching data requirements from the boundary scan register.
2. Test conditions are specified using the load in TAP AC test conditions. tR/tF = 1 ns.
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
23
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
TAP AC TEST CONDITIONS (2.5/3.3V)
Input pulse levels
®
TAP Output Load Equivalent
0 to 2.5V/0 to 3.0V
Input rise and fall times
1ns
Input timing reference levels
1.25V/1.5V
Output reference levels
1.25V/1.5V
Test load termination supply voltage
1.25V/1.5V
50Ω
1.25V
TDO
20 pF
Z0 = 50Ω
GND
TAP TIMING
1
2
tTHTH
3
4
5
6
tTLTH
TCK
tTHTL
tMVTH tTHMX
TMS
tDVTH tTHDX
TDI
tTLOV
TDO
tTLOX
DON'T CARE
UNDEFINED
24
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
119 BGA BOUNDARY SCAN ORDER (256K X 36)
Bit #
Signal Bump
Name
ID
Bit #
Signal Bump
Name
ID
Bit #
Signal Bump
Name
ID
Bit #
Signal Bump
Name
ID
1
A
2R
19
DQb
7G
37
BWa
5L
55
DQd
2K
2
A
3T
20
DQb
6F
38
BWb
5G
56
DQd
1L
3
A
4T
21
DQb
7E
39
BWc
3G
57
DQd
2M
4
A
5T
22
DQb
7D
40
BWd
3L
58
DQd
1N
5
A
6R
23
DQb
7H
41
CE2
2B
59
DQd
1P
6
A
3B
24
DQb
6G
42
CE
4E
60
DQd
1K
7
A
5B
25
DQb
6E
43
A
3A
61
DQd
2L
8
DQa
6P
26
DQb
6D
44
A
2A
62
DQd
2N
9
DQa
7N
27
A
6A
45
DQc
2D
63
DQd
2P
10
DQa
6M
28
A
5A
46
DQc
1E
64
MODE
3R
11
DQa
7L
29
ADV
4G
47
DQc
2F
65
A
2C
12
DQa
6K
30
ADSP
4A
48
DQc
1G
66
A
3C
13
DQa
7P
31
ADSC
4B
49
DQc
2H
67
A
5C
14
DQa
6N
32
OE
4F
50
DQc
1D
68
A
6C
15
DQa
6L
33
BWE
4M
51
DQc
2E
69
A1
4N
16
DQa
7K
34
GW
4H
52
DQc
2G
70
A0
4P
17
ZZ
7T
35
CLK
4K
53
DQc
1H
18
DQb
6H
36
A
6B
54
NC
5R
119 BGA BOUNDARY SCAN ORDER (512K X 18)
Bit #
Signal Bump
Name
ID
Bit #
Signal Bump
Name
ID
Bit #
Signal Bump
Name
ID
Bit #
Signal Bump
Name
ID
1
A
2R
14
DQa
7G
27
CLK
4K
40
DQb
2K
2
A
2T
15
DQa
6F
28
A
6B
41
DQb
1L
3
A
3T
16
DQa
7E
29
BWa
5L
42
DQb
2M
4
A
5T
17
DQa
6D
30
BWb
3G
43
DQb
1N
5
A
6R
18
A
6T
31
CE2
2B
44
DQb
2P
6
A
3B
19
A
6A
32
CE
4E
45
MODE
3R
7
A
5B
20
A
5A
33
A
3A
46
A
2C
8
DQa
7P
21
ADV
4G
34
A
2A
47
A
3C
9
DQa
6N
22
ADSP
4A
35
DQb
1D
48
A
5C
10
DQa
6L
23
ADSC
4B
36
DQb
2E
49
A
6C
11
DQa
7K
24
OE
4F
37
DQb
2G
50
A1
4N
12
ZZ
7T
25
BWE
4M
38
DQb
1H
51
A0
4P
13
DQa
6H
26
GW
4H
39
NC
5R
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
25
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
165 PBGA BOUNDARY SCAN ORDER (x 36)
Bit #
Signal Bump
Name
ID
Bit #
Signal
Name
Bump
ID
Bit #
Signal
Name
Bump
ID
Bit #
Signal
Name
Bump
ID
1
MODE
1R
21
DQb
11G
41
NC
1A
61
DQd
1J
2
NC
6N
22
DQb
11F
42
CE2
6A
62
DQd
1K
3
A
11P
23
DQb
11E
43
BWa
5B
63
DQd
1L
4
A
8P
24
DQb
11D
44
BWb
5A
64
DQd
1M
5
A
8R
25
DQb
10G
45
BWc
4A
65
DQd
2J
6
A
9R
26
DQb
10F
46
BWd
4B
66
DQd
2K
7
A
9P
27
DQb
10E
47
CE2
3B
67
DQd
2L
8
A
10P
28
DQb
10D
48
CE
3A
68
DQd
2M
9
A
10R
29
DQb
11C
49
A
2A
69
DQd
1N
10
A
11R
30
NC
11A
50
A
2B
70
A
3P
11
ZZ
11H
31
A
10A
51
NC
1B
71
A
3R
12
DQa
11N
32
A
10B
52
DQc
1C
72
A
4R
13
DQa
11M
33
ADV
9A
53
DQc
1D
73
A
4P
14
DQa
11L
34
ADSP
9B
54
DQc
1E
74
A1
6P
15
DQa
11K
35
ADSC
8A
55
DQc
1F
75
A0
6R
16
DQa
11J
36
OE
8B
56
DQc
1G
17
DQa
10M
37
BWE
7A
57
DQc
2D
18
DQa
10L
38
GW
7B
58
DQc
2E
19
DQa
10K
39
CLK
6B
59
DQc
2F
20
DQa
10J
40
NC
11B
60
DQc
2G
26
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
ISSI
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
®
165 PBGA BOUNDARY SCAN ORDER (x 18)
Bit #
Signal Bump
Name
ID
Bit #
Signal
Name
Bump
ID
Bit #
Signal
Name
Bump
ID
Bit #
Signal
Name
Bump
ID
1
MODE
1R
21
DQa
11G
41
NC
1A
61
DQb
1J
2
NC
6N
22
DQa
11F
42
CE2
6A
62
DQb
1K
3
A
11P
23
DQa
11E
43
BWa
5B
63
DQb
1L
4
A
8P
24
DQa
11D
44
NC
5A
64
DQb
1M
5
A
8R
25
DQa
11C
45
BWb
4A
65
DQb
1N
6
A
9R
26
NC
10F
46
NC
4B
66
NC
2K
7
A
9P
27
NC
10E
47
CE2
3B
67
NC
2L
8
A
10P
28
NC
10D
48
CE
3A
68
NC
2M
9
A
10R
29
NC
10G
49
A
2A
69
NC
2J
10
A
11R
30
A
11A
50
A
2B
70
A
3P
11
ZZ
11H
31
A
10A
51
NC
1B
71
A
3R
12
NC
11N
32
A
10B
52
NC
1C
72
A
4R
13
NC
11M
33
ADV
9A
53
NC
1D
73
A
4P
14
NC
11L
34
ADSP
9B
54
NC
1E
74
A1
6P
15
NC
11K
35
ADSC
8A
55
NC
1F
75
A0
6R
16
NC
11J
36
OE
8B
56
NC
1G
17
DQa
10M
37
BWE
7A
57
DQb
2D
18
DQa
10L
38
GW
7B
58
DQb
2E
19
DQa
10K
39
CLK
6B
59
DQb
2F
20
DQa
10J
40
NC
11B
60
DQb
2G
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
27
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
ISSI
®
ORDERING INFORMATION (3.3V core/2.5V-3.3V I/O)
Commercial Range: 0°C to +70°C
Configuration
Order Part Number
Package(1)
250
IS61LPD25636A-250TQ
IS61LPD25636A-250B2
IS61LPD25636A-250B3
100 TQFP, 3CE
119 PBGA
165 PBGA
200
IS61LPD25636A-200TQ
IS61LPD25636A-200B2
IS61LPD25636A-200B3
100 TQFP, 3CE
119 PBGA
165 PBGA
250
IS61LPD51218A-250TQ
IS61LPD51218A-250B2
100 TQFP, 3CE
119 PBGA
IS61LPD51218A-250B3
165 PBGA
IS61LPD51218A-200TQ
IS61LPD51218A-200B2
IS61LPD51218A-200B3
100 TQFP, 3CE
119 PBGA
165 PBGA
Order Part Number
Package(1)
250
IS61LPD25636A-250TQI
IS61LPD25636A-250B2I
IS61LPD25636A-250B3I
100 TQFP, 3CE
119 PBGA
165 PBGA
200
IS61LPD25636A-200TQI
IS61LPD25636A-200TQ2I
IS61LPD25636A-200B2I
IS61LPD25636A-200B3I
100 TQFP, 3CE
100 TQFP, 2CE
119 PBGA
165 PBGA
250
IS61LPD51218A-250TQI
IS61LPD51218A-250B2I
100 TQFP, 3CE
119 PBGA
IS61LPD51218A-250B3I
165 PBGA
IS61LPD51218A-200TQI
IS61LPD51218A-200B2I
IS61LPD51218A-200B3I
100 TQFP, 3CE
119 PBGA
165 PBGA
Frequency
256Kx36
512Kx18
200
Industrial Range: -40°C to +85°C
Configuration
Frequency
256Kx36
512Kx18
200
Note:
1. For 100 TQFP, 2CE option contact SRAM Marketing at [email protected]
28
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
IS61VPD25636A, IS61VPD51218A, IS61LPD25636A, IS61LPD51218A
ISSI
®
ORDERING INFORMATION (2.5V core/2.5V I/O)
Commercial Range: 0°C to +70°C
Configuration
Order Part Number
Package(1)
IS61VPD25636A-250TQ
IS61VPD25636A-250B2
100 TQFP, 3CE
119 PBGA
IS61VPD25636A-250B3
165 PBGA
200
IS61VPD25636A-200TQ
IS61VPD25636A-200B2
IS61VPD25636A-200B3
100 TQFP, 3CE
119 PBGA
165 PBGA
250
IS61VPD51218A-250TQ
IS61VPD51218A-250B2
100 TQFP, 3CE
119 PBGA
IS61VPD51218A-250B3
165 PBGA
IS61VPD51218A-200TQ
IS61VPD51218A-200B2
IS61VPD51218A-200B3
100 TQFP, 3CE
119 PBGA
165 PBGA
Order Part Number
Package(1)
250
IS61VPD25636A-250TQI
IS61VPD25636A-250B2I
IS61VPD25636A-250B3I
100 TQFP, 3CE
119 PBGA
165 PBGA
200
IS61VPD25636A-200TQI
IS61VPD25636A-200TQ2I
IS61VPD25636A-200B2I
IS61VPD25636A-200B3I
100 TQFP, 3CE
100 TQFP, 2CE
119 PBGA
165 PBGA
250
IS61VPD51218A-250TQI
IS61VPD51218A-250B2I
IS61VPD51218A-250B3I
100 TQFP, 3CE
119 PBGA
165 PBGA
200
IS61VPD51218A-200TQI
IS61VPD51218A-200B2I
IS61VPD51218A-200B3I
100 TQFP, 3CE
119 PBGA
165 PBGA
Frequency
256Kx36
250
512Kx18
200
Industrial Range: -40°C to +85°C
Configuration
Frequency
256Kx36
512Kx18
Note:
1. For 100 TQFP, 2CE option contact SRAM Marketing at [email protected]
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. A
05/09/05
29
ISSI
PACKAGING INFORMATION
®
Plastic Ball Grid Array
Package Code: B (119-pin)
φ b (119X)
E
A
7
6
5
4
D2
D1
e
A2
A3
E2
Sym.
Min.
N0.
Leads
Max.
SEATING PLANE
INCHES
Min.
Max.
Notes:
119
A
—
2.41
—
0.095
A1
0.50
0.70
0.020
0.028
A2
0.80
1.00
0.032
0.039
A3
1.30
1.70
0.051
0.067
A4
0.56 BSC
0.60
0.90
0.024
0.035
D
21.80
22.20
0.858
0.874
20.32 BSC
0.800 BSC
D2
19.40
19.60
0.764
0.772
E
13.80
14.20
0.543
0.559
E1
E2
e
7.62 BSC
11.90
12.10
1.27 BSC
1. Controlling dimension: millimeters, unless otherwise specified.
2. BSC = Basic lead spacing between centers.
3. Dimensions D1 and E do not include mold flash protrusion and
should be measured from the bottom of the package.
4. Formed leads shall be planar with respect to one another within
0.004 inches at the seating plane.
0.022 BSC
b
D1
E1
A1
A4
MILLIMETERS
1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
30ϒ
D
3 2
0.300 BSC
0.469
0.476
0.050 BSC
Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time
without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to
obtain the latest version of this device specification before relying on any published information and before placing orders for products.
Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774
Rev. B
02/12/03
ISSI
PACKAGING INFORMATION
®
Ball Grid Array
Package Code: B (165-pin)
BOTTOM VIEW
TOP VIEW
A1 CORNER
1
2
3
4
A1 CORNER
φ b (165X)
5
6
7
8
9
10
11 10
11
9
8
7
6
5
4
3
2
1
A
A
B
B
C
C
D
D
E
E
e
F
F
G
G
D D1
H
H
J
J
K
K
L
L
M
M
N
N
P
P
R
R
e
E1
E
A2
A
A1
BGA - 13mm x 15mm
MILLIMETERS
Sym.
Min.
N0.
Leads
Nom. Max.
Notes:
1. Controlling dimensions are in millimeters.
INCHES
Min.
165
Nom. Max.
165
A
—
—
1.20
—
A1
0.25
0.33
0.40
0.010
—
0.047
0.013 0.016
A2
—
0.79
—
—
0.031
—
D
14.90
15.00
15.10
0.587
0.591
0.594
D1
13.90
14.00
14.10
0.547
0.551
0.555
E
12.90
13.00
13.10
0.508
0.512
0.516
E1
9.90
10.00
10.10
0.390
0.394
0.398
e
—
1.00
—
—
0.039
—
b
0.40
0.45
0.50
0.016
0.018
0.020
Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time
without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to
obtain the latest version of this device specification before relying on any published information and before placing orders for products.
Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774
Rev. A
06/11/03
ISSI
PACKAGING INFORMATION
TQFP (Thin Quad Flat Pack Package)
Package Code: TQ
D
D1
E
E1
N
L1
L
C
1
e
SEATING
PLANE
A2
A
b
A1
Thin Quad Flat Pack (TQ)
Inches
Millimeters
Min
Max
Min
Max
Millimeters
Symbol Min
Max
Ref. Std.
No. Leads (N)
100
A
—
1.60
—
0.063
A1
0.05 0.15
0.002 0.006
A2
1.35 1.45
0.053 0.057
b
0.22 0.38
0.009 0.015
D
21.90 22.10
0.862 0.870
D1
19.90 20.10
0.783 0.791
E
15.90 16.10
0.626 0.634
E1
13.90 14.10
0.547 0.555
e
0.65 BSC
0.026 BSC
L
0.45 0.75
0.018 0.030
L1
1.00 REF.
0.039 REF.
C
0o
7o
0o
7o
128
—
1.60
0.05 0.15
1.35 1.45
0.17 0.27
21.80 22.20
19.90 20.10
15.80 16.20
13.90 14.10
0.50 BSC
0.45 0.75
1.00 REF.
0o
7o
Integrated Silicon Solution, Inc. — 1-800-379-4774
PK13197LQ Rev. D 05/08/03
Inches
Min
Max
—
0.063
0.002 0.006
0.053 0.057
0.007 0.011
0.858 0.874
0.783 0.791
0.622 0.638
0.547 0.555
0.020 BSC
0.018 0.030
0.039 REF.
0o
7o
Notes:
1. All dimensioning and
tolerancing conforms to
ANSI Y14.5M-1982.
2. Dimensions D1 and E1 do
not include mold protrusions.
Allowable protrusion is 0.25
mm per side. D1 and E1 do
include mold mismatch and
are determined at datum
plane -H-.
3. Controlling dimension:
millimeters.
®