SAMSUNG K4S511633F

K4S511633F-Y(P)C/L/F
Mobile-SDRAM
8M x 16Bit x 4 Banks Mobile SDRAM
FEATURES
GENERAL DESCRIPTION
• 3.0V & 3.3V power supply.
The K4S511633F is 536,870,912 bits synchronous high data
rate Dynamic RAM organized as 4 x 8,388,608 words by 16 bits,
fabricated with SAMSUNG's high performance CMOS technology. Synchronous design allows precise cycle control with the
use of system clock and I/O transactions are possible on every
clock cycle. Range of operating frequencies, programmable
burst length and programmable latencies allow the same device
to be useful for a variety of high bandwidth, high performance
memory system applications.
• LVCMOS compatible with multiplexed address.
• Four banks operation.
• MRS cycle with address key programs.
-. CAS latency (1, 2 & 3).
-. Burst length (1, 2, 4, 8 & Full page).
-. Burst type (Sequential & Interleave).
• EMRS cycle with address key programs.
• All inputs are sampled at the positive going edge of the system
clock.
• Burst read single-bit write operation.
• Special Function Support.
-. PASR (Partial Array Self Refresh).
-. Internal TCSR (Temperature Compensated Self Refresh)
• DQM for masking.
• Auto refresh.
• 64ms refresh period (8K cycle).
• Commercial Temperature Operation (-25°C ~ 70°C).
• 1 /CS Support.
• 2Chips DDP 54Balls FBGA ( -YXXX -Pb, -PXXX -Pb Free).
ORDERING INFORMATION
Part No.
Max Freq.
K4S511633F-Y(P)C/L/F75
133MHz(CL3), 111MHz(CL2)
K4S511633F-Y(P)C/L/F1H
111MHz(CL2)
K4S511633F-Y(P)C/L/F1L
111MHz(CL=3)*1, 83MHz(CL2)
Interface
Package
LVCMOS
54 FBGA Pb
(Pb Free)
- Y(P)C/L/F : Normal / Low Power, Commercial Temperature(-25°C ~ 70°C)
NOTES :
1. In case of 40MHz Frequency, CL1 can be supported.
2. Samsung are not designed or manufactured for use in a device or system that is used under circumstance in which human life is potentially at stake.
Please contact to the memory marketing team in samsung electronics when considering the use of a product contained herein for any specific pur
pose, such as medical, aerospace, nuclear, military, vehicular or undersea repeater use.
Address configuration
Organization
Bank
Row
Column Address
32M x16
BA0,BA1
A0 - A12
A0 - A9
1
September 2004
K4S511633F-Y(P)C/L/F
Mobile-SDRAM
FUNCTIONAL BLOCK DIAGRAM
I/O Control
Data Input Register
Bank Select
8M x 16
8M x 16
Output Buffer
Sense AMP
Row Decoder
Row Buffer
Refresh Counter
ADD
Address Register
CLK
8M x 16
LWE
LDQM
DQi
8M x 16
Col. Buffer
LCBR
LRAS
Column Decoder
Latency & Burst Length
LCKE
Programming Register
LRAS
LCBR
LWE
LCAS
LWCBR
LDQM
Timing Register
CLK
CKE
CS
RAS
CAS
WE
2
L(U)DQM
September 2004
K4S511633F-Y(P)C/L/F
Mobile-SDRAM
Package Dimension and Pin Configuration
< Bottom View*1 >
< Top View*2 >
E1
9
8
7
6
5
4
3
2
54Ball(6x9) FBGA
1
1
2
B
A
VSS
C
B
DQ14
D
C
DQ12
E
D
DQ10
F
E
DQ8
F
UDQM
G
A12
H
A8
J
VSS
D
D1
e
A
D/2
G
H
J
3
7
8
9
DQ15
VSSQ
DQ13
VDDQ
VDDQ
DQ0
VDD
VSSQ
DQ2
DQ1
DQ11
DQ9
VSSQ
VDDQ
DQ4
DQ3
VDDQ
VSSQ
DQ6
DQ5
NC
CLK
VSS
VDD
LDQM
DQ7
CKE
CAS
RAS
WE
A11
A7
A9
BA0
BA1
CS
A6
A0
A1
A10
A5
A4
A3
A2
VDD
E
E/2
*2: Top View
A
A1
Substrate(2Layer)
b
z
*1: Bottom View
< Top View*2 >
Pin Name
Pin Function
CLK
System Clock
CS
Chip Select
CKE
Clock Enable
A0 ~ A12
Address
BA0 ~ BA1
Bank Select Address
RAS
Row Address Strobe
CAS
Column Address Strobe
WE
Write Enable
L(U)DQM
Data Input/Output Mask
DQ0 ~ 15
Data Input/Output
VDD/VSS
Power Supply/Ground
VDDQ/VSSQ
Data Output Power/Ground
#A1 Ball Origin Indicator
[Unit:mm]
SEC
Week XXXX
K4S511633F
3
Symbol
Min
Typ
Max
A
1.00
1.10
1.20
A1
0.27
0.32
0.37
E
-
11.5
-
E1
-
6.40
-
D
-
10.0
-
D1
-
6.40
-
e
-
0.80
-
b
0.45
0.50
0.55
z
-
-
0.10
September 2004
K4S511633F-Y(P)C/L/F
Mobile-SDRAM
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Value
Unit
Voltage on any pin relative to Vss
VIN, VOUT
-1.0 ~ 4.6
V
Voltage on VDD supply relative to Vss
VDD, VDDQ
-1.0 ~ 4.6
V
TSTG
-55 ~ +150
°C
Power dissipation
PD
1.0
W
Short circuit current
IOS
50
mA
Storage temperature
NOTES:
Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded.
Functional operation should be restricted to recommended operating condition.
Exposure to higher than recommended voltage for extended periods of time could affect device reliability.
DC OPERATING CONDITIONS
Recommended operating conditions (Voltage referenced to VSS = 0V, TA = -25 to 70°C)
Parameter
Symbol
Min
Typ
Max
Unit
Note
VDD
2.7
3.0
3.6
V
VDDQ
2.7
3.0
3.6
V
Input logic high voltage
VIH
2.2
3.0
VDDQ + 0.3
V
1
Input logic low voltage
VIL
-0.3
0
0.5
V
2
Output logic high voltage
VOH
2.4
-
-
V
IOH = -2mA
Output logic low voltage
VOL
-
-
0.4
V
IOL = 2mA
ILI
-2
-
2
uA
3
Supply voltage
Input leakage current
NOTES :
1. VIH (max) = 5.3V AC.The overshoot voltage duration is ≤ 3ns.
2. VIL (min) = -2.0V AC. The undershoot voltage duration is ≤ 3ns.
3. Any input 0V ≤ VIN ≤ VDDQ.
Input leakage currents include Hi-Z output leakage for all bi-directional buffers with tri-state outputs.
4. Dout is disabled, 0V ≤ VOUT ≤ VDDQ.
CAPACITANCE (VDD = 1.8V, TA = 23°C, f = 1MHz, VREF =0.9V ± 50 mV)
Pin
Symbol
Min
Max
Unit
CCLK
3.0
6.0
pF
RAS, CAS, WE, CS, CKE
CIN
3.0
6.0
pF
DQM
CIN
1.5
3.0
pF
Address
CADD
3.0
6.0
pF
DQ0 ~ DQ15
COUT
3.0
5.0
pF
Clock
4
Note
September 2004
K4S511633F-Y(P)C/L/F
Mobile-SDRAM
DC CHARACTERISTICS
Recommended operating conditions (Voltage referenced to VSS = 0V, TA = -25 to 70°C)
Version
Parameter
Operating Current
(One Bank Active)
Precharge Standby Current in
power-down mode
Symbol
ICC1
ICC2P
Precharge Standby Current
in non power-down mode
ICC2NS
Active Standby Current
in non power-down mode
(One Bank Active)
Operating Current
(Burst Mode)
Refresh Current
Burst length = 1
tRC ≥ tRC(min)
IO = 0 mA
-75
-1H
-1L
120
120
110
CKE ≤ VIL(max), tCC = 10ns
ICC3P
ICC3NS
Note
mA
1
mA
1.0
CKE ≥ VIH(min), CS ≥ VIH(min), tCC = 10ns
Input signals are changed one time during 20ns
20
CKE ≥ VIH(min), CLK ≤ VIL(max), tCC = ∞
Input signals are stable
10
CKE ≤ VIL(max), tCC = 10ns
8
mA
mA
ICC3PS CKE & CLK ≤ VIL(max), tCC = ∞
ICC3N
Unit
1.0
ICC2PS CKE & CLK ≤ VIL(max), tCC = ∞
ICC2N
Active Standby Current
in power-down mode
Test Condition
4
CKE ≥ VIH(min), CS ≥ VIH(min), tCC = 10ns
Input signals are changed one time during 20ns
45
mA
CKE ≥ VIH(min), CLK ≤ VIL(max), tCC = ∞
Input signals are stable
30
mA
ICC4
IO = 0 mA
Page burst
4Banks Activated
tCCD = 2CLKs
170
150
150
mA
1
ICC5
tRC ≥ tRC(min)
300
280
240
mA
2
-C
1500
4
uA
-L
Self Refresh Current
ICC6
CKE ≤ 0.2V
1200
5
Internal TCSR
Max 40
Max 70
Full Array
900
1200
1/2 of Full Array
800
900
1/4 of Full Array
700
800
°C
3
uA
6
-F
NOTES:
1. Measured with outputs open.
2. Refresh period is 64ms.
3. Internal TCSR can be supported(In commercial Temp : Max 40°C/Max 70°C).
4. K4S511633F-Y(P)C**
5. K4S511633F-Y(P)L**
6. K4S511633F-Y(P)F**
7. Unless otherwise noted, input swing IeveI is CMOS(VIH /VIL=VDDQ/VSSQ).
5
September 2004
K4S511633F-Y(P)C/L/F
Mobile-SDRAM
AC OPERATING TEST CONDITIONS(VDD = 2.7V ∼ 3.6V, TA = -25 to 70°C )
Parameter
AC input levels (Vih/Vil)
Input timing measurement reference level
Input rise and fall time
Output timing measurement reference level
Output load condition
Value
Unit
2.4/0.4
V
1.4
V
tr/tf = 1/1
ns
1.4
V
See Figure 2
VDDQ
1200Ω
Vtt=0.5 x VDDQ
VOH (DC) = 2.4V, IOH = -2mA
Output
VOL (DC) = 0.4V, IOL = 2mA
870Ω
50Ω
30pF
Output
Z0=50Ω
30pF
Figure 1. DC Output Load Circuit
Figure 2. AC Output Load Circuit
6
September 2004
K4S511633F-Y(P)C/L/F
Mobile-SDRAM
OPERATING AC PARAMETER
(AC operating conditions unless otherwise noted)
Version
Parameter
Symbol
-75
-1H
-1L
Unit
Note
Row active to row active delay
tRRD(min)
15
18
18
ns
1
RAS to CAS delay
tRCD(min)
18
18
24
ns
1
Row precharge time
tRP(min)
18
18
24
ns
1
tRAS(min)
45
50
60
ns
1
Row active time
tRAS(max)
Row cycle time
tRC(min)
Last data in to row precharge
tRDL(min)
Last data in to Active delay
100
63
68
us
ns
1
2
CLK
2
tDAL(min)
tRDL + tRP
-
3
Last data in to new col. address delay
tCDL(min)
1
CLK
2
Last data in to burst stop
tBDL(min)
1
CLK
2
Col. address to col. address delay
tCCD(min)
1
CLK
4
ea
5
Number of valid output data
CAS latency=3
2
Number of valid output data
CAS latency=2
1
Number of valid output data
CAS latency=1
84
0
NOTES:
1. The minimum number of clock cycles is determined by dividing the minimum time required with clock cycle time
and then rounding off to the next higher integer.
2. Minimum delay is required to complete write.
3. Minimum tRDL=2CLK and tDAL(= tRDL + tRP) is required to complete both of last data write command(tRDL) and precharge command(tRP).
4. All parts allow every cycle column address change.
5. In case of row precharge interrupt, auto precharge and read burst stop.
7
September 2004
K4S511633F-Y(P)C/L/F
Mobile-SDRAM
AC CHARACTERISTICS(AC operating conditions unless otherwise noted)
-75
Parameter
-1H
-1L
Symbol
Min
Max
Min
Max
9.0
Min
Unit
Note
ns
1
ns
1,2
ns
2
Max
CLK cycle time
CAS latency=3
tCC
7.5
CLK cycle time
CAS latency=2
tCC
9.0
CLK cycle time
CAS latency=1
tCC
-
CLK to valid output delay
CAS latency=3
tSAC
5.4
7
7
CLK to valid output delay
CAS latency=2
tSAC
7
7
8
CLK to valid output delay
CAS latency=1
tSAC
-
-
20
Output data hold time
CAS latency=3
tOH
2.5
2.5
2.5
Output data hold time
CAS latency=2
tOH
2.5
2.5
2.5
Output data hold time
CAS latency=1
tOH
-
-
2.5
CLK high pulse width
tCH
2.5
3.0
3.0
ns
3
CLK low pulse width
tCL
2.5
3.0
3.0
ns
3
Input setup time
tSS
2.0
2.5
2.5
ns
3
Input hold time
tSH
1.0
1.5
1.5
ns
3
CLK to output in Low-Z
tSLZ
1
1
1
ns
2
1000
CAS latency=2
1000
-
CAS latency=3
CLK to output in Hi-Z
9.0
9.0
tSHZ
CAS latency=1
12
1000
25
5.4
7
7
7
7
8
-
-
20
ns
NOTES :
1. Parameters depend on programmed CAS latency.
2. If clock rising time is longer than 1ns, (tr/2-0.5)ns should be added to the parameter.
3. Assumed input rise and fall time (tr & tf) = 1ns.
If tr & tf is longer than 1ns, transient time compensation should be considered,
i.e., [(tr + tf)/2-1]ns should be added to the parameter.
8
September 2004
K4S511633F-Y(P)C/L/F
Mobile-SDRAM
SIMPLIFIED TRUTH TABLE
COMMAND
Register
CKEn-1 CKEn
Mode Register Set
H
Auto Refresh
X
Entry
Self
Refresh
RAS
CAS
WE
L
L
L
L
X
OP CODE
L
L
L
H
X
X
L
H
H
H
Exit
3
L
L
3
H
3
X
H
X
X
X
X
3
Bank Active & Row Addr.
H
X
L
L
H
H
X
V
Read &
Auto Precharge Disable
Column Address
Auto Precharge Enable
H
X
L
H
L
H
X
V
Write &
Auto Precharge Disable
Column Address
Auto Precharge Enable
H
X
L
H
L
L
X
V
Burst Stop
H
X
L
H
H
L
X
Precharge
Column
Address
(A0~A9)
H
L
H
X
L
L
H
L
H
H
X
X
X
L
V
V
V
X
X
X
X
H
X
X
X
L
H
H
H
H
X
X
X
L
V
V
V
L
Exit
L
H
Entry
H
L
Precharge Power Down
Mode
Column
Address
(A0~A9)
H
X
V
L
X
H
X
All Banks
Entry
Row Address
L
Bank Selection
Clock Suspend or
Active Power Down
1, 2
H
H
Refresh
DQM BA0,1 A10/AP
A11, A12
Note
A9 ~ A0
CS
4
4, 5
4
4, 5
6
X
X
X
X
X
X
Exit
L
DQM
H
No Operation Command
H
H
X
X
H
X
X
X
L
H
H
H
X
V
X
X
X
7
(V=Valid, X=Don′t Care, H=Logic High, L=Logic Low)
NOTES :
1. OP Code : Operand Code
A0 ~ A12 & BA0 ~ BA1 : Program keys. (@MRS)
2. MRS can be issued only at all banks precharge state.
A new command can be issued after 2 CLK cycles of MRS.
3. Auto refresh functions are the same as CBR refresh of DRAM.
The automatical precharge without row precharge command is meant by "Auto".
Auto/self refresh can be issued only at all banks precharge state.
Partial self refresh can be issued only after setting partial self refresh mode of EMRS.
4. BA0 ~ BA1 : Bank select addresses.
5. During burst read or write with auto precharge, new read/write command can not be issued.
Another bank read/write command can be issued after the end of burst.
New row active of the associated bank can be issued at tRP after the end of burst.
6. Burst stop command is valid at every burst length.
7. DQM sampled at the positive going edge of CLK masks the data-in at that same CLK in write operation (Write DQM latency
is 0), but in read operation, it makes the data-out Hi-Z state after 2 CLK cycles. (Read DQM latency is 2).
9
September 2004
K4S511633F-Y(P)C/L/F
Mobile-SDRAM
A. MODE REGISTER FIELD TABLE TO PROGRAM MODES
Register Programmed with Normal MRS
Address
Function
BA0 ~ BA1
A12 ~ A10/AP
A9*2
"0" Setting for
Normal MRS
RFU*1
W.B.L
A8
A7
A6
Test Mode
A5
A4
A3
CAS Latency
A2
BT
A1
A0
Burst Length
Normal MRS Mode
Test Mode
CAS Latency
Burst Type
Burst Length
A8
A7
Type
A6
A5
A4
Latency
A3
Type
A2
A1
A0
BT=0
BT=1
0
0
Mode Register Set
0
0
0
Reserved
0
Sequential
0
0
0
1
1
0
1
Reserved
0
0
1
1
1
Interleave
0
0
1
2
2
1
0
Reserved
0
1
0
2
0
1
0
4
4
1
1
Reserved
0
1
1
3
0
1
1
8
8
Write Burst Length
1
0
0
Reserved
1
0
0
Reserved
Reserved
1
0
1
Reserved
Reserved
1
1
0
Reserved
Reserved
1
1
1
Full Page
Reserved
A9
Length
1
0
1
Mode Select
BA1 BA0
Setting
for Normal MRS
Reserved
0
0
Burst
1
1
0
Reserved
1
Single Bit
1
1
1
Reserved
Mode
0
Full Page Length x16 : 256Mb(512)
Register Programmed with Extended MRS
Address
BA1
Function
BA0
A12 ~ A10/AP
Mode Select
A9
A8
A7
A6
A5
A4
DS
RFU*1
A3
A2
A1
A0
PASR
RFU*1
EMRS for PASR(Partial Array Self Ref.) & DS(Driver Strength)
Mode Select
Driver Strength
PASR
BA1
BA0
Mode
A6
A5
Driver Strength
A2
A1
A0
Size of Refreshed Array
0
0
Normal MRS
0
0
Full
0
0
0
Full Array
0
1
Reserved
0
1
1/2
0
0
1
1/2 of Full Array
1
0
EMRS for Mobile SDRAM
1
0
Reserved
0
1
0
1/4 of Full Array
1
1
Reserved
1
1
Reserved
0
1
1
Reserved
1
0
0
Reserved
1
0
1
Reserved
1
1
0
Reserved
1
1
1
Reserved
Reserved Address
A12~A10/AP
A9
A8
A7
A4
A3
0
0
0
0
0
0
NOTES:
1.RFU(Reserved for future use) should stay "0" during MRS cycle.
2.If A9 is high during MRS cycle, "Burst Read Single Bit Write" function will be enabled.
10
September 2004
K4S511633F-Y(P)C/L/F
Mobile-SDRAM
Partial Array Self Refresh
1. In order to save power consumption, Mobile SDRAM has PASR option.
2. Mobile SDRAM supports 3 kinds of PASR in self refresh mode : Full Array, 1/2 of Full Array and 1/4 of Full Array.
BA1=0
BA0=0
BA1=0
BA0=1
BA1=0
BA0=0
BA1=0
BA0=1
BA1=0
BA0=0
BA1=0
BA0=1
BA1=1
BA0=0
BA1=1
BA0=1
BA1=1
BA0=0
BA1=1
BA0=1
BA1=1
BA0=0
BA1=1
BA0=1
- Full Array
- 1/4 Array
- 1/2 Array
Partial Self Refresh Area
Temperature Compensated Self Refresh
1. In order to save power consumption, Mobile-DRAM includes the internal temperature sensor and control units to control the self
refresh cycle automatically according to the two temperature range : Max 40 °C and Max 70 °C.
2. If the EMRS for external TCSR is issued by the controller, this EMRS code for TCSR is ignored.
Self Refresh Current (Icc6)
Temperature Range
-F
-C
Max 70 °C
Max 40 °C
1500
Unit
-L
Full Array
1/2 of Full Array
1/4 of Full Array
1200
900
800
900
800
700
1200
uA
B. POWER UP SEQUENCE
1. Apply power and attempt to maintain CKE at a high state and all other inputs may be undefined.
- Apply VDD before or at the same time as VDDQ.
2. Maintain stable power, stable clock and NOP input condition for a minimum of 200us.
3. Issue precharge commands for all banks of the devices.
4. Issue 2 or more auto-refresh commands.
5. Issue a mode register set command to initialize the mode register.
6. Issue a extended mode register set command to define DS or PASR operating type of the device after normal MRS.
EMRS cycle is not mandatory and the EMRS command needs to be issued only when DS or PASR is used.
The default state without EMRS command issued is full driver strength and full array refreshed.
The device is now ready for the operation selected by EMRS.
For operating with DS or PASR , set DS or PASR mode in EMRS setting stage.
In order to adjust another mode in the state of DS or PASR mode, additional EMRS set is required but power up sequence is not
needed again at this time. In that case, all banks have to be in idle state prior to adjusting EMRS set.
11
September 2004
K4S511633F-Y(P)C/L/F
Mobile-SDRAM
C. BURST SEQUENCE
1. BURST LENGTH = 4
Initial Address
Sequential
Interleave
A1
A0
0
0
0
1
2
3
0
1
2
3
0
1
1
2
3
0
1
0
3
2
1
0
2
3
0
1
2
3
0
1
1
1
3
0
1
2
3
2
1
0
2. BURST LENGTH = 8
Initial Address
Sequential
Interleave
A2
A1
A0
0
0
0
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
0
1
1
2
3
4
5
6
7
0
1
0
3
2
5
4
7
6
0
1
0
2
3
4
5
6
7
0
1
2
3
0
1
6
7
4
5
0
1
1
3
4
5
6
7
0
1
2
3
2
1
0
7
6
5
4
1
0
0
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
1
0
1
5
6
7
0
1
2
3
4
5
4
7
6
1
0
3
2
1
1
0
6
7
0
1
2
3
4
5
6
7
4
5
2
3
0
1
1
1
1
7
0
1
2
3
4
5
6
7
6
5
4
3
2
1
0
12
September 2004