SANYO LV8498CT

Ordering number : ENA1625B
Bi-CMOS IC
For VCMs
LV8498CT
Constant-current Driver IC
Overview
The LV8498CT is a constant current driver IC for voice coil motors that supports I2C control integrating a digital/analog
converter (DAC). It uses an ultraminiature WLP package and includes a current detection resistor for constant current
control, which makes the IC ideal for miniaturization of camera modules intended for use in camera-equipped mobile
phones. The output transistor has a low on-resistance of 1Ω and the resistance of the built-in current detection resistor is
1Ω, which minimizes the voltage loss and helps withstand voltage drop in VCC. The function is incorporated, which, by
changing the current in a stepped pattern while taking time at rise and fall of the output current, provides the current a slope,
improving the converging stability of the voice coil motor (current slope function).
Functions
• Constant current driver for voice coil motors.
• Constant current control enabled by DAC (10 bits).
2
• I C bus control supported.
• Wide operating voltage range (2.2 to 5.0V).
• Built-in current detection resistor.
• 6-pin WLP package used (1.27 × 0.87 × 0.25mm).
• Built-in voltage drop protection circuit (VCC = 2V output off). • Built-in thermal protection circuit.
• Low output block total-resistance of 2Ω helps withstand voltage drop in VCC. (Current detection resistance + output
transistor on-resistance).
• Built-in VCM overshoot preventive function (current slope function).
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter
Symbol
Conditions
Ratings
Unit
Maximum supply voltage
VCC max
Output voltage
VOUT max
Input voltage
VIN max
GND pin source current
IGND
Allowable power dissipation
Pd max
Operating temperature
Topr
-30 to +85
°C
Storage temperature
Tstg
-40 to +150
°C
SCL, SDA, ENA
With specified substrate *
5.5
V
VCC + 0.5
V
5.5
V
200
mA
350
mW
* Specified substrate : 40mm × 40mm × 1.6mm, Single layer glass epoxy substrate
Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to
"standard application", intended for the use as general electronics equipment (home appliances, AV equipment,
communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be
intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace
instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety
equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case
of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee
thereof. If you should intend to use our products for applications outside the standard applications of our
customer who is considering such use and/or outside the scope of our intended standard applications, please
consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our
customer shall be solely responsible for the use.
Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate
the performance, characteristics, and functions of the described products in the independent state, and are not
guarantees of the performance, characteristics, and functions of the described products as mounted in the
customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent
device, the customer should always evaluate and test devices mounted in the customer' s products or
equipment.
53011 SY/52511 SY/31710 SY 20091119-S00001 No.A1625-1/8
LV8498CT
Allowable Operating Conditions at Ta = 25°C
Parameter
Symbol
Supply voltage
VCC
Maximum preset output current
IO
Input signal voltage
VIN
Conditions
Ratings
Unit
2.2 to 5.0
150
-0.3 to VCC+0.3
V
mA
V
Electrical Characteristics at Ta = 25°C, VCC = 2.8V
Ratings
Parameter
Symbol
Conditions
Unit
min
Supply current
typ
max
ICC0a
ENA = 0V, SCL=SDA=VCC
1
μA
ICC0b
ENA=SCL=SDA=VCC, PD = 1
1
μA
ICC0c
ENA=SCL=SDA=VCC, D0 to D9 = 0
1
μA
0.5
3
mA
0
1
μA
VCC-0.3
V
ICC1
ENA=SCL=SDA=VCC , D0 to D9 ≠ 0
Input current
IIN
SCL, SDA, ENA
High level input voltage
VIH
Applied to SCL, SDA and ENA pin.
Low level input voltage
VIL
Total resistance value of the output block
(built-in resistor + transistor on-resistance)
RTTL
-1
1.5
-0.3
VCC = 2.8V, IOUT = 80mA
2
0.5
V
3
Ω
DAC block
Resolution
10
bits
Relative accuracy
INL
±2
LSB
Differential linearity
DNL
±1
LSB
Full code current
Ifull
D0 to D9 = 1
150
mA
Error code current 0
Izero
D0 to D9 = 0
0
mA
Spark killer diode
Reverse current
IS (leak)
Forward voltage
VSF
IOUT=100mA
1
μA
1.3
V
外形図
unit:mm (typ)
3390
B
0.4
A
0.235
0.33 MAX
0.22
0.4
1
2
1.27
3
0.87
0.08
SIDE VIEW
Pd max -- Ta
0.4
BOTTOM VIEW
Allowable power dissipation, Pd max -- W
SIDE VIEW
0.235
TOP VIEW
Specified board : 40 × 40 × 1.6mm3
Single layer glass epoxy
0.35
0.3
0.2
0.18
0.1
0
--30 --20
0
20
40
60
80
100
120
Ambient temperature, Ta -- °C
SANYO : WLP6K(1.27X0.87)
No.A1625-2/8
LV8498CT
Pin Assignment
Bottom View ( Ball side up )
2
3
1
0.4
A
0.4
0.87
Pin No.
Pin Name
A1
SCL
Pin Description
I2C SCL input pin
A2
ENA
Enable & reset *1, 2
A3
GND
Ground
B1
SDA
I2C SDA input pin
B2
VCC
Power supply pin
B3
OUT
Output pin
B
*1 : Setting the ENA pin to low powers down and resets the IC.
It is necessary to power on the IC by setting the ENA pin to
low and hold it high during normal operation.
*2 : When the ENA pin is to be used with pull_up, it is necessary to
send code 0 in advance after power-on.
1.27
Block Diagram
VCC
ENA
ON/OFF
Bias
Reference
voltage
Voltage drop protection
&
thermal protection
RESET
VCM
SDA
SCL
I2C
IF
I2C
DECODE
DAC
10bit
current
setting
+
-
OUT
RF
Timing genaration
GND
No.A1625-3/8
LV8498CT
Serial Bus Communication Specifications
I2C serial transfer timing conditions
Standard mode
twH
SCL
th1
twL
th2
tbuf
SDA
th1
ts2
ts1
ts3
Resend start condition
Start condition
ton
Stop condition
tof
Input waveform condition
Standard mode
Parameter
SCL clock frequency
Data setup time
Data hold time
Pulse width
Input waveform conditions
Bus free time
symbol
fscl
Conditions
min
SCL clock frequency
typ
0
max
unit
100
kHz
ts1
Setup time of SCL with respect to the falling edge of SDA
4.7
μs
ts2
Setup time of SDA with respect to the rising edge of SCL
250
ns
μs
ts3
Setup time of SCL with respect to the rising edge of SDA
4.0
th1
Hold time of SCL with respect to the rising edge of SDA
4.0
μs
th2
Hold time of SDA with respect to the falling edge of SCL
0
μs
twL
SCL low period pulse width
4.7
μs
twH
SCL high period pulse width
4.0
ton
SCL, SDA (input) rising time
1000
ns
tof
SCL, SDA (input) falling time
300
ns
tbuf
Interval between stop condition and start condition
μs
μs
4.7
High-speed mode
Parameter
Symbol
Conditions
min
typ
unit
SCL clock frequency
fscl
SCL clock frequency
Data setup time
ts1
Setup time of SCL with respect to the falling edge of SDA
0.6
μs
ts2
Setup time of SDA with respect to the rising edge of SCL
100
ns
μs
Data hold time
Pulse width
Input waveform conditions
Bus free time
0
max
400
kHz
ts3
Setup time of SCL with respect to the rising edge of SDA
0.6
th1
Hold time of SCL with respect to the rising edge of SDA
0.6
μs
th2
Hold time of SDA with respect to the falling edge of SCL
0
μs
twL
SCL low period pulse width
1.3
μs
twH
SCL high period pulse width
0.6
ton
SCL, SDA (input) rising time
300
ns
tof
SCL, SDA (input) falling time
300
ns
tbuf
Interval between stop condition and start condition
1.3
μs
μs
No.A1625-4/8
LV8498CT
2
I C bus transmission method
Start and stop conditions
The I2C bus requires that the state of SDA be preserved while SCL is high as shown in the timing diagram below during a
data transfer operation.
SCL
SDA
ts2
th2
When data is not being transferred, both SCL and SDA are in the high state. The start condition is generated and access is
started when SDA is changed from high to low while SCL and SDA are high.
Conversely, the stop condition is generated and access is ended when SDA is changed from low to high while SCL is
high.
Start condition
Stop condition
th1
th3
SCL
SDA
Data transfer and acknowledgement response
After the start condition has been generated, the data is transferred one byte (8 bits) at a time. Generally, in an I2C bus, a
unique 7-bit slave address is assigned to each device, and the first byte of the transfer data is allocated to the 7-bit slave
address and to the command (R/W) indicating the transfer direction of the subsequent data. However, this IC is provided
with only a write mode for receiving the data. Every time 8 bits of data for each byte are transferred, the ACK signal is
sent from the receiving end to the sending end. Immediately after the clock pulse of SCL bit 8 in the data transferred has
fallen to low, SDA at the sending end is released, and SDA is set to low at the receiving end, causing the ACK signal to be
sent. When, after the receiving end has sent the ACK signal, the transfer of the next byte remains in the receiving status,
the receiving end releases SDA at the falling edge of the ninth SCL clock.
M
S
B
Start
Slave address
L
S
B
W
A
C
K
M
S
B
Data
L
S
B
A
C
K
M
S
B
SCL
2nd byte
1st byte
A1 A2 A3 A4 A5 A6 A7 0
SDA
L
S
B
A
C
K
M
S
B
Data
L
S
B
PD X D9 D8 D7 D6 D5 D4
A
C
K
M
S
B
Data
L
S
B
A
C
K
Stop
SCL
3rd byte
SDA
D3 D2 D1 D0 X X X X
4th byte
ST2 ST1 ST0TM2TM1TM0
X X
T CARE
No.A1625-5/8
LV8498CT
The standard data transfer to this device consists of four bytes : the slave address of the first byte and the data of the second,
third and four bytes.
Slave address : 0110011(0)
PD : Power-down
The table below shows the format of the second , third and four bytes.
2nd byte
3rd byte
Serial data bits
SD7
SD6
SD5
SD4
SD3
SD2
SD1
SD0
SD7
SD6
SD5
SD4
SD3
SD2
SD1
SD0
Function
PD
×
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
×
×
×
×
4th byte
SD7
SD6
SD5
SD4
SD3
SD2
SD1
SD0
ST2
ST1
ST0
TM2
TM1
TM0
x
x
PD : Power_down ( PD = 1 : standby mode and reset )
D0-D9 setting method
Output current (mA)
Current setting code
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
1
0.147
2
0
0
0
0
0
0
0
0
1
0
0.293
3
0
0
0
0
0
0
0
0
1
1
0.586
1021
1
1
1
1
1
1
1
1
0
1
149.70
1022
1
1
1
1
1
1
1
1
1
0
149.85
1023
1
1
1
1
1
1
1
1
1
1
150
(design value)
Current slope function operation image chart
At VCM energing ON
At VCM energing OFF
current setting code
IST
IST
TST
TST
No.A1625-6/8
LV8498CT
TIM
000
001
010
011
100
101
110
111
STP
000
001
010
011
At current slope OFF
0.147
0.032
0.064
0.147
0.128
0.147
0.256
0.147
0.512
0.147
1.024
0.147
2.048
0.147
4.096
0.147
0.064
0.128
0.256
0.512
1.024
2.048
4.096
8.192
0.293
0.293
0.293
0.293
0.293
0.293
0.293
0.293
0.128
0.256
0.586
0.512
0.586
1.024
0.586
2.048
0.586
4.096
0.586
8.192
0.586
16.38
0.586
0.512
1.173
1.024
1.173
2.048
1.173
4.096
1.173
8.192
1.173
16.38
1.173
32.77
1.173
1.024
2.346
2.048
2.346
4.096
2.346
8.192
2.346
16.38
2.346
32.77
2.346
65.54
2.346
2.048
4.692
4.096
4.692
8.192
4.692
16.38
4.692
32.77
4.692
65.54
4.692
131.08
4.692
9.383
4.096
9.383
8.192
9.383
16.38
9.383
32.77
9.383
65.54
9.383
131.08
9.383
262.16
9.383
32.7
65.5
130.9
261.9
523.8
1047.6
2095.1
4190.2
0.586
100
0.256
1.173
101
0.512
2.346
110
1.024
4.692
111
FULL_CODE
2.048
Sweep time
In the upper row in the above table each column , the lower is a current step value (IST:mA) , at the step time (Tst:msec).
Relationship between the ENA pin input, I2C input data PD, and current setting 0 (code 0)
This IC supports the following three modes of setting up the standby mode :
1) Setting the ENA pin low.
2) Setting the PD bit to 1 (high) with I2C input data.
3) Setting the output current to 0 with I2C input data.
Execution of one of the steps 1) to 3) causes the output current to 0 and stops operation of the circuit.
When the ENA pin is set low, the I2C data register is reset and the IC is reset to its default state (PD bit set to 0 and output
current setting to code 0).
When the ENA pin is to be used with pull_up to VCC, it is necessary to send code 0 once after VCC ON.
No.A1625-7/8
LV8498CT
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of May, 2011. Specifications and information herein are subject
to change without notice.
PS No.A1625-8/8