MAXIM MAX19586

19-3758; Rev 0; 8/05
KIT
ATION
EVALU
E
L
B
AVAILA
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
PART
TEMP RANGE
-40°C to +85°C 56 Thin QFN-EP
MAX19586ETN+ -40°C to +85°C 56 Thin QFN-EP
MAX19586ETN
T5688-2
DVDD
DGND
DGND
D0
D1
D5
D6
D7
D8
DVDD
DVDD
TOP VIEW
42 41 40 39 38 37 36 35 34 33 32 31 30 29
D9 43
28 AGND
D10 44
27 REFIN
Multistandard Receivers
D11 45
26 REFOUT
D12 46
25 AVDD
E911 Location Receivers
D13 47
24 AVDD
D14 48
23 AVDD
High-Performance Instrumentation
D15 49
22 AGND
MAX19586
DAV 50
Antenna Array Processing
T5688-2
Pin Configuration
Wireless Local Loop (WLL)
Multicarrier Receivers
PKG
CODE
+Denotes lead-free package.
Applications
Cellular Base-Station Transceiver Systems (BTS)
PIN-PACKAGE
D2
The MAX19586 features parallel, low-voltage CMOScompatible outputs in two’s-complement output format.
The MAX19586 is manufactured in an 8mm x 8mm,
56-pin thin QFN package with exposed paddle (EP) for
low thermal resistance, and is specified for the extended industrial (-40°C to +85°C) temperature range.
Ordering Information
D3
The MAX19586 operates from a 3.3V analog supply
voltage and a 1.8V digital voltage, features a 2.56VP-P
full-scale input range, and allows for a guaranteed sampling speed of up to 80Msps. The input track-and-hold
stage operates with a 600MHz full-scale, full-power
bandwidth.
♦ 80Msps Minimum Sampling Rate
♦ -82dBFS Noise Floor
♦ Excellent Dynamic Performance
80dB/79.2dB SNR at fIN = 10MHz/70MHz
and -2dBFS
96dBc/102dBc Single-Tone SFDR1/
SFDR2 at fIN = 10MHz
84.3dBc/100dBc Single-Tone SFDR1/
SFDR2 at fIN = 70MHz
♦ Less than 0.1ps Sampling Jitter
♦ 1.1W Power Dissipation
♦ 2.56VP-P Fully Differential Analog Input Voltage
Range
♦ CMOS-Compatible Two’s-Complement Data
Output
♦ Separate Data Valid Clock and Over-Range
Outputs
♦ Flexible Input Clock Buffer
♦ 3.3V Analog Power Supply; 1.8V Digital Output
Supply
♦ Small 8mm x 8mm x 0.8mm 56-Pin Thin QFN
Package
♦ EV Kit Available for MAX19586
(Order MAX19586EVKIT)
D4
The MAX19586 is a 3.3V, high-speed, high-performance analog-to-digital converter (ADC) featuring a
fully differential wideband track-and-hold (T/H) and a
16-bit converter core. The MAX19586 is optimized for
multichannel, multimode receivers, which require the
ADC to meet very stringent dynamic performance
requirements. With a -82dBFS noise floor, the
MAX19586 allows for the design of receivers with superior sensitivity requirements.
At 80Msps, the MAX19586 achieves a 79.2dB signal-tonoise ratio (SNR) and an 84.3dBc/100dBc single-tone
spurious-free dynamic range (SFDR) performance
(SFDR1/SFDR2) at fIN = 70MHz. The MAX19586 is not
only optimized for excellent dynamic performance in
the 2nd Nyquist region, but also for high-IF input frequencies. For instance, at 130MHz, the MAX19586
achieves an 82.5dBc SFDR and its SNR performance
stays flat (within 2.5dB) throughout the 4th Nyquist
region. This level of performance makes the part ideal
for high-performance digital receivers.
Features
21 AGND
DVDD 51
20 AGND
DGND 52
19 AVDD
DOR 53
18 AVDD
N.C. 54
17 AVDD
AVDD 55
16 N.C.
15 N.C.
10 11 12 13 14
AGND
CLKN
9
AGND
CLKP
8
AGND
AGND
7
INN
AVDD
6
INP
5
AGND
4
AGND
3
AGND
2
AGND
1
AVDD
AVDD 56
THIN QFN
8mm x 8mm
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX19586
General Description
MAX19586
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
ABSOLUTE MAXIMUM RATINGS
AVDD to AGND ..................................................... -0.3V to +3.6V
DVDD to DGND..................................................... -0.3V to +2.4V
AGND to DGND.................................................... -0.3V to +0.3V
INP, INN, CLKP, CLKN, REFP, REFN,
REFIN, REFOUT to AGND....................-0.3V to (AVDD + 0.3V)
D0–D15, DAV, DOR, DAV to GND...........-0.3V to (DVDD + 0.3V)
Continuous Power Dissipation (TA = +70°C)
56-Pin Thin QFN
(derate 47.6mW/°C above +70°C) .........................3809.5mW
Operating Temperature Range ..........................-40°C to +85°C
Thermal Resistance θJA ..................................................21°C/W
Thermal Resistance θJC .................................................0.6°C/W
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-60°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(AVDD = 3.3V, DVDD = 1.8V, AGND = DGND = 0, INP and INN driven differentially, internal reference CLKP and CLKN driven differentially,
CL = 5pF at digital outputs, fCLK = 80MHz, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C, unless otherwise
noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DC ACCURACY
Resolution
N
Offset Error
VOS
0
16
Gain Error
GE
-3.5
10
Bits
20
mV
+3.5
%FS
ANALOG INPUTS (INP, INN)
Input Voltage Range
VDIFF
Fully differential input, VIN = VINP - VINN
2.56
VP-P
Common-Mode Voltage
VCM
Internally self-biased
2.2
V
Differential Input Resistance
RIN
10
±20%
kΩ
Differential Input Capacitance
CIN
7
pF
Full-Power Analog Bandwidth
BW-3dB
600
MHz
1.28
±10%
V
1.28
V
AIN < -35dBFS
-82
dBFS
fIN = 10MHz, AIN = -2dBFS
80
-3dB rolloff for FS Input
REFERENCE INPUT/OUTPUT (REFIN, REFOUT)
Reference Input Voltage Range
REFIN
Reference Output Voltage
REFOUT
DYNAMIC SPECIFICATIONS (fCLK = 80Msps)
Thermal Plus Quantization Noise
Floor
Signal-to-Noise Ratio
(First 4 Harmonics Excluded)
(Notes 2, 3)
NF
fIN = 70MHz, AIN = -2dBFS
SNR
77.5
78.5
fIN = 130MHz, AIN = -2dBFS
77.9
fIN = 168MHz, AIN = -2dBFS
77.2
fIN = 10MHz, AIN = -2dBFS
Signal-to-Noise Plus Distortion
(Notes 2, 3)
2
fIN = 70MHz, AIN = -2dBFS
SINAD
79.2
fIN = 100MHz, AIN = -2dBFS
dB
79.6
75
77.6
fIN = 100MHz, AIN = -2dBFS
77.4
fIN = 130MHz, AIN = -2dBFS
76.4
fIN = 168MHz, AIN = -2dBFS
72.7
_______________________________________________________________________________________
dB
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
(AVDD = 3.3V, DVDD = 1.8V, AGND = DGND = 0, INP and INN driven differentially, internal reference CLKP and CLKN driven differentially,
CL = 5pF at digital outputs, fCLK = 80MHz, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C, unless otherwise
noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
fIN = 10MHz, AIN = -2dBFS
Spurious-Free Dynamic Range
(Worst Harmonic, 2nd and 3rd)
Spurious-Free Dynamic Range
(Worst Harmonic, 4th and Higher)
(Note 3)
Second-Order Harmonic
Distortion
Third-Order Harmonic Distortion
Two-Tone Intermodulation
Distortion
Two-Tone SFDR
fIN = 70MHz, AIN = -2dBFS
SFDR1
HD2
HD3
TTIMD
TTSFDR
MAX
UNITS
96
80
84.3
fIN = 100MHz, AIN = -2dBFS
84
fIN = 130MHz, AIN = -2dBFS
82.5
fIN = 168MHz, AIN = -2dBFS
78
fIN = 10MHz, AIN = -2dBFS
102
fIN = 70MHz, AIN = -2dBFS
SFDR2
TYP
90
100
fIN = 100MHz, AIN = -2dBFS
92
fIN = 130MHz, AIN = -2dBFS
94
fIN = 168MHz, AIN = -2dBFS
90
fIN = 10MHz, AIN = -2dBFS
-100
fIN = 70MHz, AIN = -2dBFS
-95
fIN = 100MHz, AIN = -2dBFS
-94
fIN = 130MHz, AIN = -2dBFS
-88.8
fIN = 168MHz, AIN = -2dBFS
-78
fIN = 10MHz, AIN = -2dBFS
-96
fIN = 70MHz, AIN = -2dBFS
-84.3
fIN = 100MHz, AIN = -2dBFS
-84
fIN = 130MHz, AIN = -2dBFS
-82.5
fIN = 168MHz, AIN = -2dBFS
-78
fIN1 = 65.1MHz, AIN = -8dBFS
fIN2 = 70.1MHz, AIN = -8dBFS
fIN1 = 65.1MHz, fIN2 = 70.1MHz
-100dBFS < AIN < -10dBFS
dBc
dBc
-84
dBc
-80
dBc
-85.2
dBc
99
dBFS
CONVERSION RATE
Maximum Conversion Rate
fCLKMAX
Minimum Conversion Rate
fCLKMIN
Aperture Jitter
80
MHz
20
tJ
MHz
0.094
psRMS
1.0 to
5.0
VP-P
CLOCK INPUTS (CLKP, CLKN)
Differential Input Swing
VDIFFCLK
Fully differential inputs
Common-Mode Voltage
VCMCLK
Self-biased
1.6
V
Differential Input Resistance
RINCLK
10
kΩ
Differential Input Capacitance
CINCLK
3
pF
CMOS-COMPATIBLE DIGITAL OUTPUTS (D0–D15, DOR, DAV)
Digital Output High Voltage
VOH
ISOURCE = 200µA
Digital Output Low Voltage
VOL
ISINK = 200µA
DVDD 0.2
V
0.2
V
_______________________________________________________________________________________
3
MAX19586
ELECTRICAL CHARACTERISTICS (continued)
MAX19586
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
ELECTRICAL CHARACTERISTICS (continued)
(AVDD = 3.3V, DVDD = 1.8V, AGND = DGND = 0, INP and INN driven differentially, internal reference CLKP and CLKN driven differentially,
CL = 5pF at digital outputs, fCLK = 80MHz, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C, unless otherwise
noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
TIMING SPECIFICATION (Figures 4, 5), CL = 5pF (D0–D15, DOR); CL = 15pF (DAV)
CLKP - CLKN High
tCLKP
(Note 2)
5
CLKP - CLKN Low
tCLKN
(Note 2)
5
ns
ns
Effective Aperture Delay
tAD
-300
ps
Output Data Delay
tDAT
3.3
ns
Data Valid Delay
tDAV
Pipeline Latency
(Note 2)
2.8
tP
3.8
5.0
7
CLKP Rising Edge to DATA Not
Valid
tDNV
(Note 2)
CLKP Rising Edge to DATA
Guaranteed Valid
tDGV
(Note 2)
ns
Clock
Cycles
1.2
ns
6.5
ns
DATA Setup Time Before Rising
DAV
tS
Clock duty cycle = 50% (Note 2)
3
ns
DATA Hold Time After Rising
DAV
tH
Clock duty cycle = 50% (Note 2)
3
ns
POWER SUPPLIES
Analog Power-Supply Voltage
AVDD
3.13
3.3
3.46
V
Digital Output Power-Supply
Voltage
DVDD
1.7
1.8
1.9
V
Analog Power-Supply Current
IAVDD
320
382
mA
Digital Output Power-Supply
Current
IDVDD
28
35
mA
Power Dissipation
PDISS
1105
1325
mW
Note 1: ≥ +25°C guaranteed by production test, < +25°C guaranteed by design and characterization. Typical values are at TA = +25°C.
Note 2: Parameter guaranteed by design and characterization.
Note 3: AC parameter measured in a 32,768-point FFT record, where the first 2 bins of the FFT and 2 bins on either side of the carrier
are excluded.
4
_______________________________________________________________________________________
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
-80
-100
-120
5
10
15
20
25
30
35
40
-40
-60
-80
MAX19586 toc03
MAX19586 toc02
-100
2
2
-120
-140
0
5
10
15
20
25
30
35
40
0
5
10
15
20
25
30
35
40
ANALOG INPUT FREQUENCY (MHz)
ANALOG INPUT FREQUENCY (MHz)
ANALOG INPUT FREQUENCY (MHz)
SNR/SINAD vs. ANALOG INPUT FREQUENCY
(fCLK = 80MHz, AIN = -2dBFS)
SFDR1/SFDR2 vs. ANALOG INPUT FREQUENCY
(fCLK = 80MHz, AIN = -2dBFS)
HD2/HD3 vs. ANALOG INPUT FREQUENCY
(fCLK = 80MHz, AIN = -2dBFS)
SINAD
74
72
70
100
-75
-80
SFDR2
HD2/HD3 (dBc)
78
95
90
85
20
40
60
-90
-95
80
-100
75
-105
80 100 120 140 160 180
HD2
-110
0
20
40
60
80 100 120 140 160 180
0
20
40
60
80 100 120 140 160 180
fIN (MHz)
fIN (MHz)
fIN (MHz)
SNR vs. ANALOG INPUT AMPLITUDE
(fCLK = 80MHz, fIN = 10.10011MHz)
SFDR1 vs. ANALOG INPUT AMPLITUDE
(fCLK = 80MHz, fIN = 10.10011MHz)
SFDR2 vs. ANALOG INPUT AMPLITUDE
(fCLK = 80MHz, fIN = 10.10011MHz)
SFDR1 (dBc, dBFS)
70
65
60
SNR (dB)
SFDR1 (dBFS)
110
100
90
SFDR1 (dBc)
80
50
SFDR = 90dB
REFERENCE LINE
70
45
40
-30
-25
-20
-15
-10
-5
ANALOG INPUT AMPLITUDE (dBFS)
0
SFDR2 (dBFS)
110
100
SFDR2 (dBc)
90
80
SFDR = 90dB
REFERENCE LINE
70
60
-35
120
MAX19586toc09
SNR (dBFS)
75
55
120
SFDR2 (dBc, dBFS)
80
MAX19586toc07
85
-40
HD3
-85
SFDR1
70
0
MAX19586toc06
105
SFDR1/SFDR2 (dBc)
SNR
-70
MAX19586toc05
80
76
110
MAX19586toc04
82
SNR/SINAD (dB)
3
-120
0
SNR (dB, dBFS)
-80
-100
3
2
-60
fCLK = 80.00012288MHz
fIN = 130.00050486MHz
AIN = -1.82dBFS
SNR = 77.7dB
SINAD = 76.4dB
SFDR1 = 83.1dBc
SFDR2 = 91.2dBc
HD2 = -89.4dBc
HD3 = -83.1dBc
3
-20
AMPLITUDE (dBFS)
-60
-40
0
MAX19586toc08
AMPLITUDE (dBFS)
-40
fCLK = 80.00012288MHz
fIN = 70.16368199MHz
AIN = -2.06dBFS
SNR = 79.3dB
SINAD = 77.7dB
SFDR1 = 83.3dBc
SFDR2 = 98.2dBc
HD2 = -93.5dBc
HD3 = -83.3dBc
-20
AMPLITUDE (dBFS)
fCLK = 80.00012288MHz
fIN = 10.10011317MHz
AIN = -2.02dBFS
SNR = 80dB
SINAD = 79.8dB
SFDR1 = 96.2dBc
SFDR2 = 101dBc
HD2 = -99.6dBc
HD3 = -96.2dBc
-20
0
MAX19586 toc01
0
60
-40
-35
-30
-25
-20
-15
-10
-5
ANALOG INPUT AMPLITUDE (dBFS)
0
-40
-35
-30
-25
-20
-15
-10
-5
0
ANALOG INPUT AMPLITUDE (dBFS)
_______________________________________________________________________________________
5
MAX19586
Typical Operating Characteristics
(AVDD = 3.3V, DVDD = 1.8V, INP and INN driven differentially, internal reference, CLKP and CLKN driven differentially, CL = 5pF at
digital outputs, fCLK = 80MHz, TA = +25°C. Unless otherwise noted, all AC data based on 32k-point FFT records and under coherent
sampling conditions.)
FFT PLOT
FFT PLOT
FFT PLOT
(32,768-POINT RECORD)
(32,768-POINT RECORD)
(261,244-POINT DATA RECORD)
Typical Operating Characteristics (continued)
(AVDD = 3.3V, DVDD = 1.8V, INP and INN driven differentially, internal reference, CLKP and CLKN driven differentially, CL = 5pF at
digital outputs, fCLK = 80MHz, TA = +25°C. Unless otherwise noted, all AC data based on 32k-point FFT records and under coherent
sampling conditions.)
SNR vs. ANALOG INPUT AMPLITUDE
SFDR1 vs. ANALOG INPUT AMPLITUDE
SFDR2 vs. ANALOG INPUT AMPLITUDE
(fCLK = 80MHz, fIN = 70.163683MHz)
(fCLK = 80MHz, fIN = 70.163683MHz)
(fCLK = 80MHz, fIN = 70.163683MHz)
SFDR1 (dBc, dBFS)
SNR (dB)
65
60
55
45
SFDR1 (dBc)
80
70
SFDR = 90dB
REFERENCE LINE
35
-35
-30
-25
-20
-15
-10
-5
0
MAX19586toc12
SFDR2 (dBc)
80
70
SFDR = 90dB
REFERENCE LINE
50
40
-40
90
60
50
40
40
-40
-35
-30
-25
-20
-15
-10
-5
-40
0
-35
-30
-25
-20
-15
-10
-5
ANALOG INPUT AMPLITUDE (dBFS)
ANALOG INPUT AMPLITUDE (dBFS)
ANALOG INPUT AMPLITUDE (dBFS)
SNR/SINAD vs. SAMPLING FREQUENCY
(fIN = 9.9757395MHz, AIN = -2dBFS)
SFDR/SFDR2 vs. SAMPLING FREQUENCY
(fIN = 10.10011MHz, AIN = -2dBFS)
HD2/HD3 vs. SAMPLING FREQUENCY
(fIN = 10.10011MHz, AIN = -2dBFS)
79
110
SFDR1/SFDR2 (dBc)
SNR
SINAD
77
-70
SFDR2
105
100
95
SFDR1
90
-80
HD2/HD3 (dBc)
81
115
85
75
0
MAX19586toc15
120
MAX19586toc13
83
SNR/SINAD (dB)
100
90
60
50
SFDR2 (dBFS)
110
MAX19586toc14
SNR (dB, dBFS)
75
70
SFDR1 (dBFS)
100
SFDR2 (dBc, dBFS)
80
120
MAX19586toc11
SNR (dBFS)
85
110
MAX19586toc10
90
-90
HD2
-100
HD3
-110
80
73
75
20
30
40
50
60
70
80
30
40
50
60
70
80
20
90 100 110
30
40
50
60
70
80
90 100 110
fCLK (MHz)
fCLK (MHz)
SNR/SINAD vs. SAMPLING FREQUENCY
(fIN = 70.163683MHz, AIN = -2dBFS)
SFDR1/SFDR2 vs. SAMPLING FREQUENCY
(fIN = 70.163683MHz, AIN = -2dBFS)
HD2/HD3 vs. SAMPLING FREQUENCY
(fIN = 70.163683MHz, AIN = -2dBFS)
76
SINAD
HD3
-80
95
90
85
MAX19586toc18
-75
HD2/HD3 (dBc)
78
SFDR2
-70
MAX19586toc17
100
SFDR/SFDR2 (dBc)
SNR
105
MAX19586toc16
80
SFDR1
-85
-90
HD2
-95
-100
74
80
72
-105
75
20
30
40
50
60
70
fCLK (MHz)
6
-120
20
90 100 110
fCLK (MHz)
82
SNR/SINAD (dB)
MAX19586
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
80
90 100 110
-110
20
30
40
50
60
70
fCLK (MHz)
80
90 100 110
20
30
40
50
60
70
fCLK (MHz)
_______________________________________________________________________________________
80
90 100 110
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
115
-85
110
SINAD
79
78
-90
SFDR2
105
HD2/HD3 (dBc)
SFDR1/SFDR2 (dBc)
SNR
80
100
SFDR1
95
80
-40
-15
10
35
60
HD2
-115
-40
-15
10
35
60
-40
85
-15
10
35
60
85
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
SNR/SINAD vs. TEMPERATURE
(fCLK = 80MHz, fIN = 70.163683MHz,
AIN = -2dBFS)
SFDR1/SFDR2 vs. TEMPERATURE
(fCLK = 80MHz, fIN = 70.163683MHz,
AIN = -2dBFS)
HD2/HD3 vs. TEMPERATURE
(fCLK = 80MHz, fIN = 70.163683MHz,
AIN = -2dBFS)
SNR
110
-75
SINAD
77
HD2/HD3 (dBc)
SFDR1/SFDR2 (dBc)
78
100
90
SFDR1
HD3
-80
SFDR2
79
MAX19586toc24
80
-70
MAX19586toc23
120
MAX19586toc22
81
SNR/SINAD (dB)
85
HD3
-100
-110
85
76
-95
-105
90
77
MAX19586toc21
-80
MAX19586toc20
81
SNR/SINAD (dB)
120
MAX19586toc19
82
80
-85
-90
HD2
-95
-100
-105
70
75
60
10
35
60
-115
-40
-15
10
35
60
85
-40
-15
10
60
TEMPERATURE (°C)
TEMPERATURE (°C)
POWER DISSIPATION
vs. TEMPERTURE
REFERENCE VOLTAGE
vs. TEMPERTURE
POWER DISSIPATION
vs. ANALOG SUPPLY VOLTAGE
1080
1040
fCLK = 80.00012288MHz
fIN = 70.163683MHz
AIN = -2dBFS
1.295
1300
MAX19586toc26
1.300
1.290
1200
1100
IAVCC, PDISS (mA, mW)
1120
1.285
1.280
1.275
1.270
fCLK = 80.00012288MHz
fIN = 70.163683MHz
AIN = -2dBFS
1000
10
35
TEMPERATURE (°C)
60
85
PDISS
900
800
700
600
500
IAVCC
300
200
1.260
-15
85
1000
400
1.265
-40
35
TEMPERATURE (°C)
fCLK = 80.00012288MHz
fIN = 70.163683MHz
AIN = -2dBFS
1160
85
REFERENCE VOLTAGE (V)
POWER DISSIPATION (mW)
1200
-15
MAX19586toc25
-40
-110
MAX19586toc27
76
-40
-15
10
35
TEMPERATURE (°C)
60
85
3.15
3.20
3.25
3.30
3.35
3.40
3.45
ANALOG SUPPLY VOLTAGE (V)
_______________________________________________________________________________________
7
MAX19586
Typical Operating Characteristics (continued)
(AVDD = 3.3V, DVDD = 1.8V, INP and INN driven differentially, internal reference, CLKP and CLKN driven differentially, CL = 5pF at
digital outputs, fCLK = 80MHz, TA = +25°C. Unless otherwise noted, all AC data based on 32k-point FFT records and under coherent
sampling conditions.)
SNR/SINAD vs. TEMPERATURE
SFDR1/SFDR2 vs. TEMPERATURE
HD2/HD3 vs. TEMPERATURE
(fCLK = 80MHz, fIN = 10.10011MHz,
(fCLK = 80MHz, fIN = 10.10011MHz,
(fCLK = 80MHz, fIN = 10.10011MHz,
AIN = -2dBFS)
AIN = -2dBFS)
AIN = -2dBFS)
Typical Operating Characteristics (continued)
(AVDD = 3.3V, DVDD = 1.8V, INP and INN driven differentially, internal reference, CLKP and CLKN driven differentially, CL = 5pF at
digital outputs, fCLK = 80MHz, TA = +25°C. Unless otherwise noted, all AC data based on 32k-point FFT records and under coherent
sampling conditions.)
SFDR1/SFDR2 vs.
ANALOG SUPPLY VOLTAGE
80
SNR/SINAD (dB)
1.283
1.280
1.278
78
77
SINAD
76
95
90
85
75
80
1.273
74
75
73
3.25
3.30
3.35
3.40
3.45
fCLK = 80.00012288MHz
fIN = 70.163683MHz
AIN = -2dBFS
3.20
3.25
3.30
3.35
3.40
3.45
3.15
3.20
3.25
3.30
3.35
3.40
ANALOG SUPPLY VOLTAGE (V)
ANALOG SUPPLY VOLTAGE (V)
ANALOG SUPPLY VOLTAGE (V)
HD2/HD3 vs.
ANALOG SUPPLY VOLTAGE
TWO-TONE SFDR PLOT
(32,768-POINT DATA RECORD)
TWO-TONE SFDR PLOT
(32,768-POINT DATA RECORD)
0
-20
AMPLITUDE (dBFS)
-80
HD3
-85
-90
HD2
fIN1
-40
fIN2
fCLK = 80MHz
fIN1 = 10.1001MHz
fIN2 = 14.871MHz
AIN1 = -8.04dBFS
AIN2 = -8.00dBFS
TTSFDR = 99.6dBFS
0
-20
AMPLITUDE (dBFS)
fCLK = 80.00012288MHz
fIN = 70.163683MHz
AIN = -2dBFS
-95
SFDR2
70
3.15
MAX19586 toc32
-60
-80
fIN2
fIN1
-40
3.45
fCLK = 80MHz
fIN1 = 65.1002MHz
fIN2 = 70.1MHz
AIN1 = -8.03dBFS
AIN2 = -8.00dBFS
TTSFDR = 93.2dBFS
-60
2fIN1 - fIN2
-80
fIN1 + fIN2
-100
-100
-105
-110
-100
-120
3.15
3.20
3.25
3.30
3.35
3.40
3.45
-120
0
ANALOG SUPPLY VOLTAGE (V)
5
10
15
20
25
30
35
MAX19586toc34
SFDR (dBFS)
SFDR (dBc)
SFDR = 90dB
REFERENCE LINE
-100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0
ANALOG INPUT AMPLITUDE (dBFS)
5
10
15
20
25
120
110
100
90
80
70
60
50
40
30
20
10
0
30
35
ANALOG INPUT FREQUENCY (MHz)
TWO-TONE SFDR vs. ANALOG INPUT
AMPLITUDE (fCLK = 80MHz,
fIN1 = 65.1MHz, fIN2 = 70.1MHz)
TTSFDR (dBc, dBFS)
TTSFDR (dBc, dBFS)
0
ANALOG INPUT FREQUENCY (MHz)
TWO-TONE SFDR vs. ANALOG INPUT
AMPLITUDE (fCLK = 80MHz,
fIN1 = 10.1MHz, fIN2 = 14.87MHz)
120
110
100
90
80
70
60
50
40
30
20
10
0
40
SFDR (dBFS)
SFDR (dBc)
SFDR = 90dB
REFERENCE LINE
-100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0
ANALOG INPUT AMPLITUDE (dBFS)
_______________________________________________________________________________________
MAX19586toc35
-70
-75
3.20
MAX19586to31
3.15
SFDR1
100
1.275
1.270
8
105
SFDR1/SFDR2 (dBc)
79
1.285
110
MAX19586toc30
fCLK = 80.00012288MHz
fIN = 70.163683MHz
SNR
AIN = -2dBFS
MAX19586 toc33
fCLK = 80.00012288MHz
fIN = 70.163683MHz
AIN = -2dBFS
REFERENCE VOLTAGE (V)
1.288
81
MAX19586toc28
1.290
SNR/SINAD vs.
ANALOG SUPPLY VOLTAGE
MAX19586toc29
REFERENCE VOLTAGE
vs. ANALOG SUPPLY VOLTAGE
HD2/HD3 (dBc)
MAX19586
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
40
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
PIN
NAME
FUNCTION
1, 2, 17, 18,
19, 23, 24,
25, 55, 56
AVDD
Analog Supply Voltage. Provide local bypassing to ground with 0.01µF and 0.1µF capacitors.
3, 6–9, 12,
13, 14, 20,
21, 22, 28
AGND
Converter Ground. Analog, digital, and output-driver grounds are internally connected to the same
potential. Connect the converter’s exposed paddle (EP) to GND.
4
CLKP
Differential Clock, Positive Input Terminal
5
CLKN
Differential Clock, Negative Input Terminal
10
INP
Differential Analog Input, Positive Terminal
11
INN
Differential Analog Input, Negative/Complementary Terminal
15, 16, 54
N.C.
No Connection. Do not connect to this pin.
26
REFOUT
27
REFIN
Reference Voltage Input
29, 41, 42,
51
DVDD
Digital Supply Voltage. Provide local bypassing to ground with 0.01µF and 0.1µF capacitors.
30, 31, 52
DGND
32
D0
Digital CMOS Output Bit 0 (LSB)
33
D1
Digital CMOS Output Bit 1
34
D2
Digital CMOS Output Bit 2
35
D3
Digital CMOS Output Bit 3
36
D4
Digital CMOS Output Bit 4
37
D5
Digital CMOS Output Bit 5
38
D6
Digital CMOS Output Bit 6
39
D7
Digital CMOS Output Bit 7
40
D8
Digital CMOS Output Bit 8
43
D9
Digital CMOS Output Bit 9
44
D10
Digital CMOS Output Bit 10
45
D11
Digital CMOS Output Bit 11
46
D12
Digital CMOS Output Bit 12
47
D13
Digital CMOS Output Bit 13
48
D14
Digital CMOS Output Bit 14
49
D15
Digital CMOS Output Bit 15 (MSB)
50
DAV
Data Valid Output. This output can be used as a clock control line to drive an external buffer or dataacquisition system. The typical delay time between the falling edge of the converter clock and the
rising edge of DAV is 3.8ns.
53
DOR
Data Over-Range Bit. This control line flags an over-/under-range condition in the ADC. If DOR
transitions high, an over-/under-range condition was detected. If DOR remains low, the ADC operates
within the allowable full-scale range.
—
EP
Internal Bandgap Reference Output
Converter Ground. Digital output-driver ground.
Exposed Paddle. Must be connected to AGND.
_______________________________________________________________________________________
9
MAX19586
Pin Description
MAX19586
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
ential signal inputs to the MAX19586 should be AC-coupled and carefully balanced to achieve the best dynamic performance (see Differential, AC-Coupled Analog
Inputs in the Applications Information section for more
details). AC-coupling of the input signal is required
because the MAX19586 inputs are self-biasing as
shown in Figure 2. Although the track-and-hold inputs
are high impedance, the actual differential input impedance is nominally 10kΩ because of the two 5kΩ resistors connected to the common-mode bias circuitry.
Avoid injecting any DC leakage currents into these analog inputs. Exceeding a DC leakage current of 10µA
shifts the self-biased common-mode level, adversely
affecting the converter’s performance.
Detailed Description
Figure 1 provides an overview of the MAX19586 architecture. The MAX19586 employs an input track-andhold (T/H) amplifier, which has been optimized for low
thermal noise and low distortion. The high-impedance
differential inputs to the T/H amplifier (INP and INN) are
self-biased at 2.2V, and support a full-scale 2.56VP-P
differential input voltage. The output of the T/H amplifier
is applied to a multistage pipelined ADC core, which is
designed to achieve a very low thermal noise floor and
low distortion.
A clock buffer receives a differential input clock waveform and generates a low-jitter clock signal for the input
T/H. The signal at the analog inputs is sampled at the
rising edge of the differential clock waveform. The differential clock inputs (CLKP and CLKN) are highimpedance inputs, are self-biased at 1.6V, and support
differential clock waveforms from 1VP-P to 5VP-P.
The outputs from the multistage pipelined ADC core
are delivered to error correction and formatting logic,
which deliver the 16-bit output code in two’s-complement format to digital output drivers. The output drivers
provide 1.8V CMOS-compatible outputs.
On-Chip Reference Circuit
The MAX19586 incorporates an on-chip 1.28V, low-drift
bandgap reference. This reference potential establishes the full-scale range for the converter, which is nominally 2.56V P-P differential (Figure 3). The internal
reference voltage can be monitored by REFOUT.
To use the internal reference voltage the reference
input (REFIN) must be connected to REFOUT
through a 10kΩ resistor. Bypass both pins with separate 1µF capacitors to AGND.
The MAX19586 also allows an external reference
source to be connected to REFIN, enabling the user to
overdrive the internal bandgap reference. REFIN
accepts a 1.28V ±10% input voltage range.
Analog Inputs (INP, INN)
The signal inputs to the MAX19586 (INP and INN) are
balanced differential inputs. This differential configuration provides immunity to common-mode noise coupling
and rejection of even-order harmonic terms. The differ-
CLKP
CLKN
AVDD
CLOCK
BUFFER
AGND
DVDD
DAV
CMOS
DRIVER
INP
T/H
INN
PIPELINE
ADC
CMOS
OUTPUT
DRIVERS
DOR
D0–D15
DGND
MAX19586
REFERENCE
REFOUT
REFIN
Figure 1. Block Diagram
10
______________________________________________________________________________________
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
System Timing Requirements
Figure 4 depicts the general timing relationships for the
signal input, clock input, data output, and DAV output.
Figure 5 shows the detailed timing specifications and
signal relationships, as defined in the Electrical
Characteristics table.
The MAX19586 samples the input signal on the rising
edge of the input clock. Output data is valid on the rising edge of the DAV signal, with a 7 clock-cycle data
latency. Note that the clock duty cycle should typically
be 50% ±10% for proper operation.
T/H AMPLIFIER
TO FIRST QUANTIZER
STAGE
INP
5kΩ
OTA
5kΩ
Digital Outputs (D0–D15, DAV, DOR)
Although designed for low-voltage 1.8V logic systems,
the logic-high level of the low-voltage CMOS-compatible digital outputs (D0–D15, DAV, and DOR) offer some
flexibility, as it allows the user to select the digital voltage within the 1.7V to 1.9V range.
For best performance, the capacitive loading on the
digital outputs of the MAX19586 should be kept as low
as possible (< 10pF). Due to the current-limited dataoutput driver of the MAX19586, large capacitive loads
increase the rise and fall time of the data and can make
it more difficult to register the data into the next IC. The
loading capacitance can be kept low by keeping the
output traces short and by driving a single CMOS
buffer or latch input (as opposed to multiple CMOS
inputs). The output data is in two’s-complement format,
as illustrated in Table 1.
Data is valid at the rising edge of DAV (Figures 4, 5).
DAV may be used as a clock signal to latch the output
data. Note that the DAV output driver is not current limited, hence it allows for higher capacitive loading.
TO FIRST QUANTIZER
STAGE
INN
T/H AMPLIFIER
Figure 2. Simplified Analog Input Architecture
+640mV
2.56VP-P
DIFFERENTIAL FSR
INP
INN
COMMON-MODE
VOLTAGE (2.2V)
-640mV
Figure 3. Full-Scale Voltage Range
______________________________________________________________________________________
11
MAX19586
Clock Inputs (CLKP, CLKN)
The differential clock buffer for the MAX19586 has been
designed to accept an AC-coupled clock waveform.
Like the signal inputs, the clock inputs are self-biasing.
In this case, the self-biased potential is 1.6V and each
input is connected to the reference potential with a 5kΩ
resistor. Consequently, the differential input resistance
associated with the clock inputs is 10kΩ. While differential clock signals as low as 0.5VP-P can be used to
drive the clock inputs, best dynamic performance is
achieved with 1VP-P to 5VP-P clock input voltage levels.
Jitter on the clock signal translates directly to jitter
(noise) on the sampled signal. Therefore, the clock
source must be a very low-jitter (low-phase-noise)
source. Additionally, extremely low phase-noise oscillators and bandpass filters should be used to obtain the
true AC performance of this converter. See the
Differential, AC-Coupled Clock Inputs and Testing the
MAX19586 topics in the Applications Information section for additional details on the subject of driving the
clock inputs.
MAX19586
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
7 CLOCK-CYCLE LATENCY
N+1
N+2
N
N+3
N+7
N+4
ANALOG INPUT
N+6
N+5
CLOCK INPUT
D0–D15
N-5
N-6
N-7
N-4
N-3
N-2
N-1
DAV
Figure 4. General System and Output Timing Diagram
INP
INN
tCLKP
tA
tCLKN
CLKN
N
N+1
N+2
N+3
CLKP
tDAT
tDNV
tDGV
D0–D15
N-7
N-6
N-5
N-4
DOR
tS
tDAV
tH
DAV
ENCODE AT CLKP - CLKN > 0 (RISING EDGE)
tCLKP CLKP - CLKN > 0
tCLKN CLKP - CLKN < 0
EFFECTIVE APERTURE DELAY
tAD
tDAT DELAY FROM CLKP TO OUTPUT DATA TRANSITION
tDAV
tDNV
tDGV
tS
tH
DELAY FROM CLKN TO DATA VALID CLOCK DAV
CLKP RISING EDGE TO DATA NOT VALID
CLKP RISING EDGE TO DATA GUARANTEED VALID
DATA SETUP TIME BEFORE RISING DAV
DATA HOLD TIME AFTER RISING DAV
Figure 5. Detailed Timing Information for Clock Operation
12
______________________________________________________________________________________
N
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
MAX19586
Table 1. MAX19586 Digital Output Coding
INP
ANALOG VOLTAGE LEVEL
INN
ANALOG VOLTAGE LEVEL
D15–D0
TWO’S-COMPLEMENT CODE
VCM + 0.64V
VCM - 0.64V
0111111111111111
(positive full-scale)
VCM
VCM
0000000000000000
(midscale + δ)
1111111111111111
(midscale - δ)
VCM - 0.64V
VCM + 0.64V
1000000000000000
(negative full-scale)
The converter’s DOR output signal is used to identify
over- and under-range conditions. If the input signal
exceeds the positive or negative full-scale range for the
MAX19586 then DOR will be asserted high. The timing
for DOR is identical to the timing for the data outputs,
and DOR therefore provides an over-range indication
on a sample-by-sample basis.
Applications Information
Differential, AC-Coupled Clock Inputs
The clock inputs to the MAX19586 are driven with an
AC-coupled differential signal, and best performance is
achieved under these conditions. However, it is often
the case that the available clock source is single-ended.
Figure 6 demonstrates one method for converting a single-ended clock signal into a differential signal with a
transformer. In this example, the transformer turns ratio
from the primary to secondary side is 1:1.414. The
impedance ratio from primary to secondary is the
square of the turns ratio, or 1:2. So terminating the secondary side with a 100Ω differential resistance results in
a 50Ω load looking into the primary side of the transformer. The termination resistor in this example is comprised of the series combination of two 50Ω resistors
with their common node AC-coupled to ground.
Figure 6 illustrates the secondary side of the transformer to be coupled directly to the clock inputs. Since
the clock inputs are self-biasing, the center tap of the
transformer must be AC-coupled to ground or left floating. If the center tap of the transformer’s secondary
side is DC-coupled to ground, it is necessary to add
blocking capacitors in series with the clock inputs.
Clock jitter is generally improved if the clock signal has
a high slew rate at the time of its zero-crossing.
Therefore, if a sinusoidal source is used to drive the
clock inputs the clock amplitude should be as large as
possible to maximize the zero-crossing slew rate. The
back-to-back Schottky diodes shown in Figure 6 are not
required as long as the input signal is held to a differential voltage potential of 3VP-P or less. If a larger amplitude signal is provided (to maximize the zero-crossing
slew rate), then the diodes serve to limit the differential
signal swing at the clock inputs. Note that all AC specifications for the MAX19586 are measured within this
configuration and with an input clock amplitude of
approximately 12dBm.
Any differential mode noise coupled to the clock inputs
translates to clock jitter and degrades the SNR performance of the MAX19586. Any differential mode coupling
of the analog input signal into the clock inputs results in
harmonic distortion. Consequently, it is important that the
clock lines be well isolated from the analog signal input
and from the digital outputs. See the Signal Routing section for more discussion on the subject of noise coupling.
Differential, AC-Coupled Analog Inputs
The analog inputs INP and INN are driven with a differential AC-coupled signal. It is important that these
inputs be accurately balanced. Any common-mode signal applied to these inputs degrades even-order distortion terms. Therefore, any attempt at driving these
inputs in a single-ended fashion will result in significant
even-order distortion terms.
Figure 7 presents one method for converting a singleended signal to a balanced differential signal using a
transformer. The primary-to-secondary turns ratio in this
example is 1:1.414. The impedance ratio is the square
of the turns ratio, so in this example the impedance ratio
is 1:2. To achieve a 50Ω input impedance at the primary
side of the transformer, the secondary side is terminated
with a 100Ω differential load. This load, in shunt with the
differential input resistance of the MAX19586, results in
a 100Ω differential load on the secondary side. It is rea-
______________________________________________________________________________________
13
MAX19586
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
sonable to use a larger transformer turns ratio to achieve
a larger signal step-up, and this may be desirable to
relax the drive requirements for the circuitry driving the
MAX19586. However, the larger the turns ratio, the larger the effect of the differential input impedance of the
MAX19586 on the primary-referred input impedance.
As stated previously, the signal inputs to the MAX19586
must be accurately balanced to achieve the best evenorder distortion performance.
AVDD DVDD
INP
D0–D15
MAX19586
16
INN
0.1µF
BACK-TO-BACK DIODE
CLKP CLKN
AGND DGND
T2-1T-KK81
49.9Ω
49.9Ω
0.1µF
Figure 6. Transformer-Coupled Clock Input Configuration
AVDD DVDD
POSITIVE
TERMINAL
0.1µF
ADT2-1T
T1-1T-KK81
INP
49.9Ω
D0–D15
MAX19586
16
49.9Ω
INN
0.1µF
CLKP CLKN
AGND DGND
Figure 7. Transformer-Coupled Analog Input Configuration with Primary-Side Balun Transformer
14
______________________________________________________________________________________
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
Testing the MAX19586
The MAX19586 has a very low thermal noise floor
(-82dBFS) and very low jitter (< 100fs). As a consequence, test system limitations can easily obscure the
SIGNAL PATH
AGILENT 8644B
BANDPASS
FILTER
10dB
3dB
PAD
BOTH SIGNAL GENERATORS
ARE PHASE-LOCKED
MAX19586
CLOCK PATH
AGILENT 8644B
BANDPASS
FILTER
Figure 8a. Standard High-Speed ADC Test Setup (Simplified
Block Diagram)
performance of the ADC. Figure 8a is a block diagram
of a conventional high-speed ADC test system. The
input signal and the clock source are generated by lowphase-noise synthesizers (e.g., Agilent 8644B).
Bandpass filters in both the signal and the clock paths
then attenuate noise and harmonic components.
Figure 8b shows the resulting power spectrum, which
results from this setup for a 70MHz input tone and an
80Msps clock. Note the substantial lift in the noise floor
near the carrier. The bandwidth of this particular noisefloor lift near the carrier corresponds to the bandwidth
of the filter in the input signal path.
Figure 8c illustrates the impact on the spectrum if the
input frequency is shifted away from the center frequency of the input signal filter. Note that the fundamental tone has moved, but the noise-floor lift remains
in the same location. This is evidence of the validity of
the claim that the lift in the noise floor is due to the test
system and not the ADC. In this figure, the magnitude
of the lift in the noise floor increased relative to the previous figure because the signal is located on the skirt of
the filter and the signal amplitude had to be increased
to obtain a signal near full scale.
To truly reveal the performance of the MAX19586, the test
system performance must be improved substantially.
Figure 8d depicts such an improved test system. In this
system, the synthesizers provide reference inputs to two
dedicated low-noise phase-locked loops (PLLs), one centered at approximately 80MHz (for the clock path) and the
other centered at 70MHz (for the signal path). The oscillators in these PLLs are very low-noise oscillators, and the
FFT PLOT
(32,768-POINT DATA RECORD)
FFT PLOT
(32,768-POINT DATA RECORD)
0
0
fCLK = 80.00012288MHz
fIN = 70.163683MHz
AIN = -2dBFS
-20
-40
POWER (dBFS)
POWER (dBFS)
-20
fCLK = 80.00012288MHz
fIN = 68MHz
AIN = -2dBFS
-60
CARRIER WAS INTENTIONALLY
LOWERED BY 2MHz TO SHOW
THE STATIONARY BEHAVIOR OF
THE NOISE
-40
-60
-80
-80
3
3
2
2
-100
-100
-120
-120
0
5
10
15
20
25
30
35
40
ANALOG INPUT FREQUENCY (MHz)
Figure 8b. 70MHz FFT with Standard High-Speed ADC Test
Setup
0
5
10
15
20
25
30
35
40
FREQUENCY (MHz)
Figure 8c. 68MHz FFT with Standard High-Speed ADC Test
Setup
______________________________________________________________________________________
15
MAX19586
One note of caution in relation to transformers is important. Any DC current passed through the primary or
secondary windings of a transformer may magnetically
bias the transformer core. When this happens the transformer is no longer accurately balanced and a degradation in the distortion of the MAX19586 may be
observed. The core must be demagnetized to return to
balanced operation.
MAX19586
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
AGILENT 8644B
SIGNAL PATH
VARIABLE
BANDPASS
ATTENUATOR
FILTER
REF
TUNE
PLL
SIGNAL
10dB
3dB
PAD
VCXO
MAX19586
LOW-NOISE PLL
AGILENT 8644B
BOTH SIGNAL GENERATORS
ARE PHASE-LOCKED
CLOCK PATH
BANDPASS
FILTER
REF
TUNE
PLL
SIGNAL
10dB
VCXO
LOW-NOISE PLL
Figure 8d. Improved Test System Employing Narrowband PLLs (Simplified Block Diagram)
FFT PLOT
(32,768-POINT DATA RECORD)
110
0
fCLK = 80.00012288MHz
fIN = 70.163683MHz
AIN = -2dBFS
-20
105
INPUT FREQUENCY = 70MHz
100
95
-40
90
SNR (dB)
ANALOG POWER (dBFS)
SNR vs. RMS
JITTER PERFORMANCE
-60
-80
80
75
3
2
-100
85
70
INPUT FREQUENCY = 140MHz
65
60
-120
0
5
10
15
20
25
30
35
40
ANALOG INPUT FREQUENCY (MHz)
Figure 8e. 70MHz FFT with Improved High-Speed ADC Test
Setup
PLLs act as extremely narrow bandwidth filters (on the
order of 20Hz) to attenuate the noise of the synthesizers.
The system provides a total system jitter on the order of
20fs. Note that while the low-noise oscillators could be
used by themselves without being locked to their respective signal sources, this would result in FFTs that are not
coherent and which would require windowing.
16
10
100
1000
RMS JITTER (fs)
Figure 8f. SNR vs. System Jitter Performance Graph
Figure 8e is an FFT plot of the spectrum obtained when
the improved test system is employed. The noise-floor
lift in the vicinity of the carrier is now almost completely
eliminated. The SNR associated with this FFT is about
79.1dB, whereas the SNR obtained using the standard
test system is on the order of 77.6dB.
______________________________________________________________________________________
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
Layer Assignments
The MAX19586 EV kit is a 6-layer board, and the
assignment of layers is discussed in this context. It is
recommended that the ground plane be on a layer
between the signal routing layer and the supply routing
layer(s). This prevents coupling from the supply lines
into the signal lines. The MAX19586 EV kit PC board
places the signal lines on the top (component) layer
and the ground plane on layer 2. Any region on the top
layer not devoted to signal routing is filled with the
ground plane with vias to layer 2. Layers 3 and 4 are
devoted to supply routing, layer 5 is another ground
plane, and layer 6 is used for the placement of additional components and for additional signal routing.
A four-layer implementation is also feasible using layer
1 for signal lines, layer 2 as a ground plane, layer 3 for
supply routing, and layer 4 for additional signal routing.
However, care must be taken to ensure that the clock
and signal lines are isolated from each other and from
the supply lines.
Signal Routing
To preserve good even-order distortion, the signal lines
(those traces feeding the INP and INN inputs) must be
carefully balanced. To accomplish this, the signal
traces should be made as symmetric as possible,
meaning that each of the two signal traces should be
the same length and should see the same parasitic
environment. As mentioned previously, the signal lines
must be isolated from the supply lines to prevent coupling from the supplies to the inputs. This is accomplished by making the necessary layer assignments as
described in the previous section. Additionally, it is crucial that the clock lines be isolated from the signal lines.
On the MAX19586 EV kit this is done by routing the
clock lines on the bottom layer (layer 6). The clock lines
then connect to the ADC through vias placed in close
proximity to the device. The clock lines are isolated
from the supply lines as well by virtue of the ground
plane on layer 5.
As with all high-speed designs, digital output traces
should be kept as short as possible to minimize capacitive loading. The ground plane on layer 2 beneath
these traces should not be removed so that the digital
ground return currents have an uninterrupted path
back to the bypass capacitors.
Grounding
The practice of providing a split ground plane in an
attempt to confine digital ground-return currents has
often been recommended in ADC application literature.
However, for converters such as the MAX19586 it is
strongly recommended to employ a single, uninterrupted ground plane. The MAX19586 EV kit achieves excellent dynamic performance with such a ground plane.
The exposed paddle of the MAX19586 should be soldered directly to a ground pad on layer 1 with vias to
the ground plane on layer 2. This provides excellent
electrical and thermal connections to the PC board.
Supply Bypassing
The MAX19586 EV kit uses 220µF capacitors (and
smaller values such as 47µF and 2µF) on power-supply
lines AV DD and DV DD to provide low-frequency
bypassing. The loss (series resistance) associated with
these capacitors is beneficial in eliminating high-Q supply resonances. Ferrite beads are also used on each of
the power-supply lines to enhance supply bypassing
(Figure 9).
Combinations of small value (0.01µF and 0.1µF), lowinductance surface-mount capacitors should be placed
at each supply pin or each grouping of supply pins to
attenuate high-frequency supply noise. Place these
capacitors on the top side of the board and as close to
the converter as possible with short connections to the
ground plane.
Parameter Definitions
Offset Error
Offset error is a figure of merit that indicates how well
the actual transfer function matches the ideal transfer
function at a single point. Ideally, the midscale
MAX19586 transition occurs at 0.5 LSB above midscale. The offset error is the amount of deviation
between the measured midscale transition point and
the ideal midscale transition point.
______________________________________________________________________________________
17
MAX19586
Figure 8f demonstrates the impact of test system jitter
on measured SNR. The figure plots SNR due to test
system jitter only, neglecting all other sources of noise,
for two different input frequencies. For example, note
that for a 70MHz input frequency a test system jitter
number of 100fs results in an SNR (due to the test system alone) of about 87.1dB. In the case of the
MAX19586, which has a -82dBFS noise floor, this is not
an inconsequential amount of additional noise.
In conclusion, careful attention must be paid to both the
input signal source and the clock signal source, if the
true performance of the MAX19586 is to be properly
characterized. Dedicated PLLs with low-noise VCOs,
such as those used in Figure 8d, are capable of providing signals with the required low jitter performance.
MAX19586
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
BYPASSING—ADC LEVEL
BYPASSING—BOARD LEVEL
DVDD
AVDD
0.01µF
AVDD
0.1µF
0.1µF
FERRITE BEAD
0.01µF
47µF
2µF
220µF
ANALOG POWERSUPPLY SOURCE
220µF
DIGITAL POWERSUPPLY SOURCE
AGND
DGND
D0–D15
DVDD
FERRITE BEAD
MAX19586
16
2µF
AGND
47µF
DGND
Figure 9. Grounding, Bypassing, and Decoupling Recommendations for the MAX19586
Gain Error
Signal-to-Noise Ratio (SNR)
Gain error is a figure of merit that indicates how well the
slope of the actual transfer function matches the slope
of the ideal transfer function. The slope of the actual
transfer function is measured between two data points:
positive full scale and negative full scale. Ideally, the
positive full-scale MAX19586 transition occurs at 1.5
LSBs below positive full scale, and the negative fullscale transition occurs at 0.5 LSB above negative full
scale. The gain error is the difference of the measured
transition points minus the difference of the ideal transition points.
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog input (RMS value) to the RMS
quantization error (residual error). The ideal, theoretical
minimum analog-to-digital noise is caused by quantization error only and results directly from the ADC’s resolution (N bits):
SNR[max] = 6.02 x N + 1.76
In reality, there are other noise sources besides quantization noise: thermal noise, reference noise, clock jitter,
etc. SNR is computed by taking the ratio of the RMS
signal to the RMS noise. RMS noise includes all spectral components to the Nyquist frequency excluding the
fundamental, the first four harmonics (HD2 through
HD5), and the DC offset.
SNR = 20 x log (SIGNALRMS / NOISERMS)
Small-Signal Noise Floor (SSNF)
Small-signal noise floor is the integrated noise and distortion power in the Nyquist band for small-signal
inputs. The DC offset is excluded from this noise calculation. For this converter, a small signal is defined as a
single tone with an amplitude of less than -35dBFS.
This parameter captures the thermal and quantization
noise characteristics of the data converter and can be
used to help calculate the overall noise figure of a digital receiver signal path.
18
Signal-to-Noise Plus Distortion (SINAD)
SINAD is computed by taking the ratio of the RMS signal to the RMS noise plus distortion. RMS noise plus
distortion includes all spectral components to the
Nyquist frequency excluding the fundamental and the
DC offset.
______________________________________________________________________________________
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
SFDR is the ratio expressed in decibels of the RMS
amplitude of the fundamental (maximum signal component) to the RMS value of the next largest spurious
component, excluding DC offset. SFDR1 reflects the
MAX19586 spurious performance based on worst 2ndor 3rd-order harmonic distortion. SFDR2 is defined by
the worst spurious component excluding 2nd- and 3rdorder harmonic spurs and DC offset.
Two-Tone Spurious-Free Dynamic
Range (TTSFDR)
Two-tone SFDR is the ratio of the full scale of the converter to the RMS value of the peak spurious component. The peak spurious component can be related to
the intermodulation distortion components, but does
not have to be. Two-tone SFDR for the MAX19586 is
expressed in dBFS.
Two-Tone Intermodulation
Distortion (TTIMD)
IMD is the total power of the IM2 to IM5 intermodulation
products to the Nyquist frequency relative to the total
input power of the two input tones fIN1 and fIN2. The
individual input tone levels are at -8dBFS. The intermodulation products are as follows:
Second-Order Intermodulation Products (IM2):
fIN1 + fIN2, fIN2 - fIN1
Third-Order Intermodulation Products (IM3):
2 x fIN1 - fIN2, 2 x fIN2 - fIN1, 2 x fIN1 + fIN2, 2 x fIN2 + fIN1
Fourth-Order Intermodulation Products (IM4):
3 x fIN1 - fIN2, 3 x fIN2 - fIN1, 3 x fIN1 + fIN2, 3 x fIN2 + fIN1,
2 x fIN1 - 2 x fIN2
Fifth-Order Intermodulation Products (IM5):
3 x fIN1 - 2 x fIN2, 3 x fIN2 - 2 x fIN1, 3 x fIN1 + 2 x fIN2,
3 x fIN2 + 2 x fIN1, 4 x fIN1 - fIN2
Note that the two-tone intermodulation distortion is measured with respect to a single-carrier amplitude and not
the peak-to-average input power of both input tones.
Aperture Jitter
Aperture jitter (tAJ) represents the sample-to-sample
variation in the aperture delay specification.
Aperture Delay
Aperture delay (tAD) is the time defined between the
rising edge of the sampling clock and the instant when
an actual sample is taken (Figure 5).
______________________________________________________________________________________
19
MAX19586
Spurious-Free Dynamic Range
(SFDR1 and SFDR2)
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
56L THIN QFN.EPS
MAX19586
High-Dynamic-Range, 16-Bit,
80Msps ADC with -82dBFS Noise Floor
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
20 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2005 Maxim Integrated Products
Freed
Printed USA
is a registered trademark of Maxim Integrated Products,
Products. Inc.