BB OPA686

®
OPA686
OPA
686
OPA
686
For most current data sheet and other product
information, visit www.burr-brown.com
Wideband, Low Noise,
Voltage Feedback OPERATIONAL AMPLIFIER
TM
FEATURES
APPLICATIONS
● HIGH BANDWIDTH: 250MHz (G = +10)
● LOW INPUT VOLTAGE NOISE: 1.3nV/√Hz
● VERY LOW DISTORTION: –90dBc (5MHz)
● HIGH DYNAMIC RANGE ADC PREAMP
● LOW NOISE, WIDEBAND,
TRANSIMPEDANCE AMPLIFIER
● HIGH SLEW RATE: 600V/µs
● HIGH DC ACCURACY
● WIDEBAND, HIGH GAIN AMPLIFIER
● LOW NOISE DIFFERENTIAL RECEIVER
● LOW SUPPLY CURRENT: 12mA
● HIGH GAIN BANDWIDTH PRODUCT:
1600MHz
● VDSL LINE RECEIVER
● ULTRASOUND CHANNEL AMPLIFIER
● IMPROVED REPLACEMENT FOR THE
CLC425
● STABLE FOR GAINS ≥ 7
DESCRIPTION
The OPA686 combines very high gain bandwidth and large
signal performance with very low input voltage noise while
dissipating a low 12mA supply current. The classical differential input stage, along with two stages of forward gain and a
high power output stage, combine to make the OPA686 an
exceptionally low distortion amplifier with excellent DC accuracy and output drive. The voltage feedback architecture allows
all standard op amp applications to be implemented with very
high performance.
The combination of low input voltage and current noise, along
with a 1.6GHz gain bandwidth product, make the OPA686 an
ideal amplifier for wideband transimpedance stages. As a voltage gain stage, the OPA686 is optimized for a flat response at a
gain of +10 and is guaranteed stable down to a noise gain of +7.
A new external compensation technique can be used to give a
very flat frequency response below the minimum stable gain
for the OPA686, further improving its already exceptional
distortion performance. Using this compensation makes the
OPA686 one of the premier 12- to 14-bit analog-to-digital
converter input drivers. The supply current for the OPA686 is
precisely trimmed to 12.4mA at +25°C. This, along with
carefully defined supply current tempcos in the input and
output stages, combine to provide exceptional performance
over the full specified temperature range.
OPA686 RELATED PRODUCTS
SINGLES
DUALS
INPUT NOISE
VOLTAGE (nV/√Hz)
2.3
800
OPA2686
1.3
1600
0.95
3600
OPA643
OPA687
GAIN BANDWIDTH
PRODUCT (MHz)
+5V
Supply decoupling
not shown.
100
20log (50kΩ) = 94dBΩ
95
0.1µF
λ
50kΩ
IS
OPA686
–5V
VO
20•log (ZT) 5dB/div
100pF
50kΩ
10pF
Photodiode
90
85
80
75
70
65
0.2pF
60
–VB
0.1
High Gain, 20MHz Transimpedance Amplifier
1
10
100
Frequency (MHz)
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111
Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
®
©
1997 Burr-Brown Corporation
1
PDS-1370D
OPA686
Printed in U.S.A. May, 2000
SPECIFICATIONS: VS = ±5V
RF = 453Ω, RL = 100Ω, and G =+10, unless otherwise noted. Figure 1 for AC performance.
OPA686U, N
TYP
PARAMETER
AC PERFORMANCE (Figure 1)
Closed-Loop Bandwidth
Gain Bandwidth Product
Bandwidth for 0.1dB Gain Flatness
Peaking at a Gain of +7
Harmonic Distortion
2nd Harmonic
3rd Harmonic
Two-Tone, 3rd-Order Intercept
Input Voltage Noise
Input Current Noise
Rise/Fall Time
Slew Rate
Settling Time to 0.01%
0.1%
1%
Differential Gain
Differential Phase
DC PERFORMANCE(4)
Open-Loop Voltage Gain (AOL)
Input Offset Voltage
Average Offset Voltage Drift
Input Bias Current
Input Bias Current Drift
Input Offset Current
Input Offset Current Drift
INPUT
Common-Mode Input Range (CMIR)(5)
Common-Mode Rejection (CMR)
Input Impedance
Differential-Mode
Common-Mode
OUTPUT
Output Voltage Swing
Current Output, Sourcing
Current Output, Sinking
Closed-Loop Output Impedance
POWER SUPPLY
Specified Operating Voltage
Maximum Operating Voltage
Max Quiescent Current
Min Quiescent Current
Power Supply Rejection Ratio
+PSRR, –PSRR
THERMAL CHARACTERISTICS
Specified Operating Range: U, N Package
Thermal Resistance, θJA
GUARANTEED
CONDITIONS
+25°C
+25°C(2)
0°C to
70°C (3)
–40°C to
+85°C (3)
G = +7, RG = 50Ω, VO = 200mVp-p
G = +10, RG = 50Ω, VO = 200mVp-p
G = +20, RG = 50Ω, VO = 200mVp-p
G ≥ +40
G = +10, RL = 100Ω, VO = 200mVp-p
425
250
100
1600
40
2
200
80
1250
35
170
65
1100
30
140
55
1000
25
–67
–85
–90
–105
40
1.5
2.3
1.75
500
–65
–80
–85
–100
39
1.6
2.4
2
400
–60
–75
–80
–95
37
1.7
2.5
2.5
310
14
12
21
14
25
18
G = +10, f = 5MHz, VO = 2Vp-p
R L = 100Ω
R L = 500Ω
R L = 100Ω
R L = 500Ω
G = +10, f = 10MHz
f > 1MHz
f > 1MHz
0.2V Step
2V Step
2V Step
2V Step
2V Step
–72
–90
–95
–110
43
1.3
1.8
1.4
600
18
16
11
G = +10, NTSC, RL = 150Ω
G = +10, NTSC, RL = 150Ω
0.02
0.02
VO = 0V
VCM = 0V
VCM = 0V
VCM = 0V
VCM = 0V
VCM = 0V
VCM = 0V
80
±0.35
±1.0
–10
–17
±0.5
±1.0
VCM = ±1V, Input Referred
±3.2
100
±3.0
VCM = 0V
VCM = 0V
6 || 2
2.9 || 1
≥ 400Ω Load
100Ω Load
VO = 0V
VO = 0V
G = +10, f = 100kHz
±3.5
±3.3
80
–80
0.008
75
90
±3.2
±3.0
UNITS
MIN/ TEST
MAX LEVEL(1)
MHz
MHz
MHz
MHz
MHz
dB
typ
min
min
min
min
typ
C
B
B
B
B
C
dBc
dBc
dBc
dBc
dBm
nV/√Hz
pA/√Hz
ns
V/µs
ns
ns
ns
max
max
max
max
min
max
max
max
min
typ
max
max
B
B
B
B
B
B
B
B
B
C
B
B
%
deg
typ
typ
C
C
70
±1.2
5
–18
50
±1.5
5
70
±1.5
10
–20
100
±1.8
10
dB
mV
µV/°C
µA
nA/°C
µA
nA/°C
min
max
max
max
max
max
max
A
A
B
A
B
A
B
±2.9
85
±2.8
75
V
dB
min
min
A
A
kΩ || pF
MΩ || pF
typ
typ
C
C
V
V
mA
mA
Ω
min
min
min
min
typ
A
A
A
A
C
±3.1
±2.8
55
–55
±3.0
±2.8
50
–40
±6
13.9
11
V
V
mA
mA
typ
max
max
min
C
A
A
A
65
dB
min
A
–40 to +85
°C
typ
C
125
150
°C/W
°C/W
typ
typ
C
C
±5
60
–60
±6
VS = ±5V
VS = ±5V
12.4
12.4
12.9
11.9
±6
13
11.9
|VS| = 4.5 to 5.5, Input Referred
78
70
70
Junction-to-Ambient
U 8-Pin, SO-8
N 5-Pin, SOT23
NOTES: (1) Test Levels: (A) 100% tested at 25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and simulation.
(C) Typical value only for information. (2) Junction temperature = ambient for 25°C guaranteed specifications. (3) Junction temperature = ambient at low temperature
limit: junction temperature = ambient +23°C at high temperature limit for over temperature guaranteed specifications. (4) Current is considered positive out-of-node.
VCM is the input common-mode voltage. (5) Tested < 3dB below minimum specified CMR at ±CMIR limits.
®
OPA686
2
PIN CONFIGURATIONS
Top View
Top View
SOT23-5
–VS
2
Non-Inverting Input
3
5
+VS
4
Inverting Input
NC
1
8
DNC
Inverting Input
2
7
+VS
Non-Inverting Input
3
6
Output
–VS
4
5
NC
4
1
5
Output
SO-8
DNC: Do Not Connect
NC: No Connection
3
2
1
A86
Pin Orientation/Package Marking
ELECTROSTATIC
DISCHARGE SENSITIVITY
ABSOLUTE MAXIMUM RATINGS
Power Supply ............................................................................... ±6.5VDC
Internal Power Dissipation ...................................... See Thermal Analysis
Differential Input Voltage .................................................................. ±1.2V
Input Voltage Range ............................................................................ ±VS
Storage Temperature Range: U, N ................................ –40°C to +125°C
Lead Temperature (soldering, 10s) .............................................. +300°C
Junction Temperature (TJ ) ........................................................... +175°C
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with appropriate
precautions. Failure to observe proper handling and installation
procedures can cause damage.
ESD damage can range from subtle performance degradation to
complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes
could cause the device not to meet its published specifications.
PACKAGE/ORDERING INFORMATION
PRODUCT
PACKAGE
PACKAGE
DRAWING
NUMBER(1)
OPA686U
"
SO-8 Surface Mount
"
182
"
–40°C to +85°C
"
OPA686U
"
OPA686U
OPA686U/2K5
Rails
Tape and Reel
OPA686N
"
5-Lead SOT23-5
"
331
–40°C to +85°C
"
A86
"
OPA686N/250
OPA686N/3K
Tape and Reel
Tape and Reel
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER(2)
TRANSPORT
MEDIA
NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) Models with a slash (/) are
available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of “OPA686U/2K5” will get a single
2500-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown IC Data Book.
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
®
3
OPA686
TYPICAL PERFORMANCE CURVES: VS = ±5V
At TA = +25°C, G = +10, RF = 453Ω, and RL = 100Ω, unless otherwise noted.
NON-INVERTING SMALL-SIGNAL
FREQUENCY RESPONSE
6
RG = 50Ω
VO = 0.2Vp-p
0
–3
G = +10
–6
–9
G = +50
–12
G = +20
–15
–18
0
–3
–6
–12
–15
–18
–21
See Figure 1
See Figure 2
–24
0.5
10
100
500
0.5
10
Frequency (MHz)
500
INVERTING LARGE-SIGNAL FREQUENCY RESPONSE
26
30
RG = 50Ω
G = +10V/V
23
29
VO = 0.2Vp-p
20
26
17
23
14
Gain (3dB/div)
Gain (3dB/div)
100
Frequency (MHz)
NON-INVERTING LARGE-SIGNAL
FREQUENCY RESPONSE
VO = 1Vp-p
11
8
VO = 2Vp-p
5
VO = 5Vp-p
RG = RS = 50Ω
G = –20V/V
VO = 0.2Vp-p
20
VO = 1Vp-p
17
VO = 2Vp-p
14
VO = 5Vp-p
11
2
8
5
See Figure 1
–4
See Figure 2
2
0.5
10
100
500
0.1
10
100
Frequency (MHz)
Frequency (MHz)
NON-INVERTING PULSE RESPONSE
INVERTING PULSE RESPONSE
Right Scale
Small Signal ±100mV
0
Left Scale
1.5
1.0
0.5
0
–0.5
–100
–1.0
–1.5
Output Voltage (100mV/div)
Large Signal ±1V
100
500
G = –20V/V
Output Voltage (500mV/div)
G = +10V/V
Output Voltage (100mV/div)
G = –20
G = –50
–9
–24
–1
G = –12
Large Signal ±1V
Right Scale
100
Small Signal ±100mV
0
Left Scale
Time (5ns/div)
OPA686
4
0.5
0
–1.0
–1.5
Time (5ns/div)
®
1.0
–0.5
–100
See Figure 2
See Figure 1
1.5
Output Voltage (500mV/div)
–21
RG = RS = 50Ω
VO = 0.2Vp-p
3
Normalized Gain (3dB/div)
Normalized Gain (3dB/div)
3
INVERTING SMALL-SIGNAL FREQUENCY RESPONSE
6
G = +7
TYPICAL PERFORMANCE CURVES: VS = ±5V
(CONT)
At TA = +25°C, G = +10, RG = 50Ω, and RL = 100Ω, unless otherwise noted. See Figure 1.
5MHz 2nd HARMONIC DISTORTION
vs OUTPUT VOLTAGE
5MHz 3rd HARMONIC DISTORTION
vs OUTPUT VOLTAGE
–70
–70
3rd Harmonic Distortion (dBc)
2nd Harmonic Distortion (dBc)
RL = 100Ω
–80
RL = 200Ω
RL = 500Ω
–90
–100
–110
RL = 100Ω
–100
RL = 200Ω
RL = 500Ω
1
10
0.1
1
10
Output Voltage (Vp-p)
Output Voltage (Vp-p)
10MHz 2nd HARMONIC DISTORTION
vs OUTPUT VOLTAGE
10MHz 3rd HARMONIC DISTORTION
vs OUTPUT VOLTAGE
–60
3rd Harmonic Distortion (dBc)
–60
2nd Harmonic Distortion (dBc)
–90
–110
0.1
RL = 100Ω
–70
RL = 200Ω
–80
RL = 500Ω
–90
–70
RL = 500Ω
–80
RL = 500Ω
–90
RL = 200Ω
–100
–100
0.1
1
10
0.1
1
10
Output Voltage (Vp-p)
Output Voltage (Vp-p)
20MHz 2nd HARMONIC DISTORTION
vs OUTPUT VOLTAGE
20MHz 3rd HARMONIC DISTORTION
vs OUTPUT VOLTAGE
–50
–50
RL = 100Ω
3rd Harmonic Distortion (dBc)
2nd Harmonic Distortion (dBc)
–80
–60
RL = 200Ω
–70
RL = 500Ω
–80
–90
–60
–70
RL = 100Ω
RL = 200Ω
–80
RL = 500Ω
–90
0.1
1
0.1
10
1
10
Output Voltage (Vp-p)
Output Voltage (Vp-p)
®
5
OPA686
TYPICAL PERFORMANCE CURVES: VS = ±5V
At TA = +25°C, G = +10, RF = 453Ω, and RL = 100Ω, unless otherwise noted. See Figure 1.
2nd HARMONIC DISTORTION vs FREQUENCY
3rd HARMONIC DISTORTION vs FREQUENCY
–50
VO = 2Vp-p
RL = 100Ω
G = +50
3rd Harmonic Distortion (dBc)
2nd Harmonic Distortion (dBc)
–50
–60
–70
G = +20
G = +10
–80
–90
VO = 2Vp-p
RL = 100Ω
–60
G = +50
–70
G = +20
–80
G = +10
–90
1
10
1
20
10
20
Frequency (MHz)
Frequency (MHz)
INPUT VOLTAGE and CURRENT NOISE DENSITY
TWO-TONE, 3rd-0RDER INTERMODULATION
INTERCEPT vs FREQUENCY
50
10
Current Noise (pA/√Hz)
Voltage Noise (nV/√Hz)
45
Intercept (dBm)
40
Current Noise
1.8pA/√Hz
35
30
PI
50Ω
PO
OPA686
50Ω
25
50Ω
453Ω
20
1.3nV/√Hz
50Ω
15
Voltage Noise
0
1
100
1k
10k
100k
1M
0
10M
5
10
15
RS vs CAPACITIVE LOAD
25
30
35
40
45
50
FREQUENCY RESPONSE vs CAPACITIVE LOAD
60
Gain to Capacitive Load (1dB/div)
22
50
40
RS (Ω)
20
Frequency (MHz)
Frequency (Hz)
30
20
10
0
CL = 10pF
21
20
CL = 20pF
19
CL = 50pF
18
17
CL = 100pF
VIN
16
RS
VO
OPA686
15
453Ω
CL
1kΩ
14
50Ω
13
1kΩ is optional
12
1
10
100
1
Capacitive Load (pF)
Frequency (MHz)
®
OPA686
10
6
100
500
TYPICAL PERFORMANCE CURVES: VS = ±5V
(CONT)
At TA = +25°C, G = +10, RF = 453Ω, and RL = 100Ω, unless otherwise noted. See Figure 1.
POWER SUPPLY and OUTPUT CURRENT
vs TEMPERATURE
–30
| AOL|
70
–60
∠ AOL
60
–90
50
–120
40
–150
30
–180
20
–210
10
–240
0
14
10k
100k
1M
10M
100M
Output Current Sourcing
100
10
8
6
60
4
40
2
20
0
–50
1G
–25
0
75
100
125
13
1.3
CMRR
100
Input Bias Current
1.1
11
+PSRR
90
80
–PSRR
70
VOS (mV)
Power Supply Rejection Ratio (dB)
50
INPUT DC ERRORS vs TEMPERATURE
CMRR and PSRR
60
50
0.9
9
0.7
7
5
0.5
Offset Voltage
40
3
0.3
30
0.1
20
1
Input Offset Current
–1
–0.1
10
100
1k
10k
100k
1M
10M
–50
100M
25
50
75
100
CLOSED-LOOP OUTPUT IMPEDANCE
DIFFERENTIAL and COMMON-MODE
INPUT IMPEDANCE
107
50Ω
OPA686
ZO
450Ω
0.1
50Ω
0.01
0.001
10k
0
Temperature (°C)
Input Impedance (Ω)
1.0
–25
Frequency (Hz)
10
Output Impedance (Ω)
25
Temperature (°C)
Frequency (Hz)
110
80
Output Current Sinking
Input Bias and Input Offset Current (µA)
1k
120
12
0
–270
100
140
Power Supply Current
Output Current (mA)
0
80
Power Supply Current (mA)
90
Open-Loop Phase (30°/div)
Open-Loop Gain (10dB/div)
OPEN-LOOP GAIN and PHASE
125
Common-Mode
106
105
Differential
104
103
100k
1M
10M
100M
100
Frequency (Hz)
1k
10k
100k
1M
10M
10M
Frequency (Hz)
®
7
OPA686
APPLICATIONS INFORMATION
WIDEBAND, INVERTING GAIN OPERATION
Operating the OPA686 as an inverting amplifier has several
benefits and is particularly appropriate when a matched
input impedance is required. Figure 2 shows the inverting
gain circuit used as the basis of the inverting mode Typical
Performance Curves.
WIDEBAND, NON-INVERTING OPERATION
The OPA686 provides a unique combination of features—
low input voltage noise along with a very low distortion
output stage—to give one of the highest dynamic range op
amps available. Its very high Gain Bandwidth Product (GBP)
can be used either to deliver high signal bandwidths at high
gains, or to deliver very low distortion signals at moderate
frequencies and lower gains. To achieve the full performance of the OPA686, careful attention to PC board layout
and component selection is required as discussed in the
remaining sections of this data sheet.
+5V
+VS
Figure 1 shows the non-inverting gain of +10 circuit used as
the basis of the Electrical Specifications and most of the
Typical Performance Curves. Most of the curves were characterized using signal sources with 50Ω driving impedance,
and with measurement equipment presenting a 50Ω load
impedance. In Figure 1, the 50Ω shunt resistor at the VI
terminal matches the source impedance of the test generator,
while the 50Ω series resistor at the VO terminal provides a
matching resistor for the measurement equipment load.
Generally, data sheet voltage swing specifications are at the
output pin (VO in Figure 1), while output power (dBm)
specifications are at the matched 50Ω load. The total 100Ω
load at the output, combined with the 503Ω total feedback
network load, presents the OPA686 with an effective output
load of 83Ω for the circuit of Figure 1.
0.1µF
50Ω Source
50Ω Load
50Ω
RF
453Ω
RG
50Ω
+
6.8µF
RF
1kΩ
+
6.8µF
WIDEBAND, HIGH SENSITIVITY, TRANSIMPEDANCE
DESIGN
The high Gain Bandwidth Product (GBP) and the low input
voltage and current noise for the OPA686 make it an ideal
wideband transimpedance amplifier for low to moderate
transimpedance gains. Very high transimpedance gains
(> 100kΩ) will benefit from the low input noise current of
a FET-input op amp such as the OPA655. Unity gain
stability in the op amp is not required for application as a
0.1µF
–VS
–5V
FIGURE 1. Non-Inverting, G = +10 Specification and Test
Circuit.
®
OPA686
OPA686
Driving this circuit from a 50Ω source, and constraining the
gain resistor (RG) to equal 50Ω, will give both a signal
bandwidth and noise advantage. R G acts as both the input
termination resistor and the gain setting resistor for the
circuit. Although the signal gain (VO/VI) for the circuit of
Figure 2 is double that for Figure 1, the noise gains are in
fact equal when the 50Ω source resistor is included. This
has the interesting effect of doubling the equivalent GBP of
the amplifier. This can be seen in comparing the G = +10
and G = –20 small-signal frequency response curves. Both
show approximately 250MHz bandwidth, but the inverting
configuration of Figure 2 gives 6dB higher signal gain. If
the signal source is actually the low impedance output of
another amplifier, RG should be increased to the minimum
load resistance value allowed for that amplifier and R F
should be adjusted to achieve the desired gain. For stable
operation of the OPA686, it is critical that this driving
amplifier show a very low output impedance at frequencies
beyond the expected closed-loop bandwidth for the OPA686.
6.8µF
+
OPA686
50Ω Load
FIGURE 2. Inverting, G = –20 Characterization Circuit.
50Ω Source
50Ω
50Ω
–VS
–5V
+VS
VO
91Ω
0.1µF
+5V
VI
RG
50Ω
VO
6.8µF
VI
Voltage feedback op amps, unlike current feedback designs,
can use a wide range of resistor values to set their gain. The
circuit of Figure 1, and the specifications at other gains, use
the constraint that RG should always be set to 50Ω and RF
adjusted to get the desired gain. Using this guideline will
guarantee that the noise added at the output due to Johnson
noise of the resistors will not significantly increase the total
noise over that due to the 1.3nV/√Hz input voltage noise for
the op amp itself.
0.1µF
+
0.1µF
8
Where:
transimpedance amplifier. One transimpedance design example is shown on the front page of the data sheet. Designs
that require high bandwidth from a large area (high capacitance) detector with relatively low transimpedance gain will
benefit from the low input voltage noise offered by the
OPA686. This input voltage noise will be peaked up over
frequency at the output by the diode source capacitance, and
can, in many cases, become the limiting factor to input
sensitivity. The key elements of the design are the expected
diode capacitance (CD) with the reverse bias voltage (–VB)
applied, the desired transimpedance gain, RF, and the GBP
of the OPA686 (1600MHz). Figure 3 shows a design using
a 50pF source capacitance diode and a 10kΩ transimpedance
gain. With these three variables set (and including the
parasitic input capacitance for the OPA686 added to CD), the
feedback capacitor value (CF) may be set to control the
frequency response.
IEQ = Equivalent input noise current if the output noise is
bandlimited to F < 1/(2πRFCD)
IN = Input current noise for the op amp inverting input
EN = Input voltage noise for the op amp
CD = Diode capacitance
F
Evaluating this expression up to the feedback pole frequency
at 15.5MHz for the circuit of Figure 3, gives an equivalent
input noise current of 6.4pA/√Hz. This is much higher than
the 1.8pA/√Hz for just the op amp itself. This result is being
dominated by the last term in the equivalent input noise
expression. It is essential in this case to use a low voltage
noise op amp. For example, if a slightly higher input noise
voltage, but otherwise identical op amp were used instead of
the OPA686 in this application (say 2.0nV/√Hz ), the total
input-referred current noise would increase to 9.5pA/√Hz.
+5V
Supply Decoupling
Not Shown
OPA686
LOW GAIN COMPENSATION FOR IMPROVED SFDR
VO = ID RF
Where a low gain is desired, and inverting operation is
acceptable, a new external compensation technique may be
used to retain the full slew rate and noise benefits of the
OPA686 while giving increased loop gain and the associated improvement in distortion offered by the decompensated architecture. This technique shapes the loop gain for
good stability while giving an easily controlled secondorder low pass frequency response. Considering only the
noise gain (non-inverting signal gain) for the circuit of
Figure 4, the low frequency noise gain, (NG1) will be set by
the resistor ratios while the high frequency noise gain (NG2)
will be set by the capacitor ratios. The capacitor values set
both the transition frequencies and the high frequency noise
gain. If this noise gain, determined by NG2 = 1+CS/CF, is set
to a value greater than the recommended minimum stable
gain for the op amp and the noise gain pole, set by 1/RFCF,
is placed correctly, a very well controlled, 2nd-order low
pass frequency response will result.
RF
10kΩ
λ
ID
CD
50pF
CF
0.8pF
–5V
= Bandlimiting frequency in Hz (usually a post filter
prior to further signal processing)
–VB
FIGURE 3. Wideband, Low Noise, Transimpendance
Amplifier.
To achieve a maximally flat 2nd-order Butterworth frequency response, the feedback pole should be set to:
1/(2πRFCF) = √(GBP/(4πRFCD))
Adding the common-mode and differential mode input capacitance (1.0 + 2.0)pF to the 50pF diode source capacitance
of Figure 3, and targeting a 10kΩ transimpedance gain using
the 1600MHz GBP for the OPA686, will require a feedback
pole set to 15.5MHz. This will require a total feedback
capacitance of 1.0pF. Typical surface-mount resistors have
a parasitic capacitance of 0.2pF, leaving the required 0.8pF
value shown in Figure 3 to get the required feedback pole.
+5V
This will give an approximate –3dB bandwidth equal to:
OPA686
f–3dB = √(GBP/2πRFCD)Hz
RG
250Ω
The example of Figure 3 will give approximately 23MHz
flat bandwidth using the 0.8pF feedback compensation.
( E N 2πC D F )
4kT  E N 
+
 +
3
RF  RF 
2
RF
500Ω
VI
CS
27pF
If the total output noise is bandlimited to a frequency less
than the feedback pole frequency, a very simple expression
for the equivalent input noise current can be derived as:
I EQ = I 2N +
VO
CF
2.9pF
–5V
2
FIGURE 4. Broadband Low Gain Inverting External Compensation.
®
9
OPA686
To choose the values for both CS and CF, two parameters and
only three equations need to be solved. The first parameter
is the target high frequency noise gain NG2, which should be
greater than the minimum stable gain for the OPA686. Here,
a target NG2 of 10.5 will be used. The second parameter is
the desired low frequency signal gain, which also sets the
low frequency noise gain NG1. To simplify this discussion,
we will target a maximally flat second-order low pass
Butterworth frequency response (Q = 0.707). The signal
gain of –2 shown in Figure 4 will set the low frequency noise
gain to NG1 = 1 + RF/RG (= 3 in this example). Then, using
only these two gains and the GBP for the OPA686
(1600MHz), the key frequency in the compensation can be
determined as:
ZO =
GBP
NG12

NG1 
NG1
 1 –
 – 1– 2
NG 2 
NG 2

12
9
Gain (3dB/div)
6
0
170MHz
–3
–6
–9
–12
–15
–18
1
10



LOW NOISE FIGURE, HIGH DYNAMIC RANGE “IF”
AMPLIFIER
The low input noise voltage of the OPA686 and its high
two-tone intercept can be used to good advantage as a fixed
gain IF amplifier. While input noise figures in the 10dB
range (for a matched 50Ω input) are easily achieved with
just OPA686 alone, Figure 6 shows a technique which
reduces the noise figure even further while providing a
broadband, low gain IF amplifier stage using the OPA686.
Finally, since CS and CF set the high frequency noise gain,
determine CS by [Using NG2 = 10.5]:
+5V
(= 27.2pF)
50Ω Load
The resulting closed-loop bandwidth will be approximately
equal to:
(= 130MHz)
f –3dB ≅ Z O GBP
OPA686
For the values shown in Figure 4, the f –3dB will be approximately 130MHz. This is less than that predicted by simply
dividing the GBP product by NG1. The compensation
network controls the bandwidth to a lower value while
providing the full slew rate at the output and an exceptional distortion performance due to increased loop gain at
frequencies below NG1 • Z0. The capacitor values shown
in Figure 4 are calculated for NG1 = 3 and NG2 = 10.5 with
no adjustment for parasitics.
50Ω Source
1:2
RG
200Ω
–5V
20pF
VO
50Ω
RF
1kΩ
2pF
FIGURE 6. Low Noise Figure IF Amplifier.
Figure 5 shows the measured frequency response for the
circuit of Figure 4. This shows the expected gain of
–2 (6dB) with exceptional flatness through 70MHz and a
–3dB bandwidth of 170MHz. Measured distortion into a
100Ω load shows > 5dB improvement through 20MHz over
the performance shown in the Typical Performance Curves.
Into a 500Ω load, the 5MHz, 2Vp-p, 2nd harmonic improves
from –90dBc to –96dBc.
Bringing the signal in through a step-up transformer to the
inverting input gain resistor has several advantages for the
OPA686. First, grounding the non-inverting input eliminates the contribution of the non-inverting input current
noise to the output noise. Secondly, the non-inverting
input voltage noise of the op amp is actually attenuated if
reflected to the input side of RG. Using the 1:2 (turns ratio)
step up transformer reflects the 50Ω source impedance at
®
OPA686
500
FIGURE 5. G = –2 Frequency Response with External
Compensation.
1
(= 2.86pF)
2π • R F Z O NG 2
C S = ( NG 2 – 1) C F
100
Frequency (MHz)
Physically, this Z0 (10.6MHz for the values shown above) is
set by 1/(2π • RF(CF + CS)) and is the frequency at which the
rising portion of the noise gain would intersect unity gain if
projected back to 0dB gain. The actual zero in the noise gain
occurs at NG1 • Z0 and the pole in the noise gain occurs at
NG2 • Z0. Since GBP is expressed in Hz, multiply Z0 by 2π
and use this to get CF by solving:
CF =
3
10
the primary through to the secondary as a 200Ω source
impedance and likewise, the 200Ω RG resistor is reflected
through to the transformer primary as a 50Ω input matching impedance. The noise gain (NG) to the amplifier
output is then 1+ 1000/400 = 3.5V/V. Taking the op amp’s
1.3nV/√Hz input voltage noise times this noise gain to the
output, then reflecting this noise term to the input side of
the RG resistor, divides it by 5. This gives a net gain of 0.7
for the non-inverting input voltage noise when reflected to
the input point for the op amp circuit. This is further
reduced when referred back to the transformer primary.
is also available for design assistance at this number. These
models do a good job of predicting small-signal AC and
transient performance under a wide variety of operating
conditions. They do not do as well in predicting the harmonic distortion characteristics. These models do not attempt to distinguish between the package types in their
small-signal AC performance.
OPERATING SUGGESTIONS
SETTING RESISTOR VALUES TO MINIMIZE NOISE
The 14dB gain to the matched load for the circuit of Figure
6 is precisely controlled (±0.2dB) and gives a 6dB noise
figure at the input of the transformer. The DC noise gain for
this circuit (3.5) is below the specified minimum stable gain.
This will improve the distortion performance at frequencies
below 20MHz from those shown in the Typical Performance
Curves. Adding the inverting compensation capacitors holds
this configuration stable as described in the previous section.
Measured results show 140MHz small-signal bandwidth for
the circuit of Figure 6 with ±0.1dB flatness through 50MHz.
The OPA686 will easily deliver a 2Vp-p ADC full-scale
input at the matched 50Ω load. Two-tone testing at 20MHz
for the circuit of Figure 6 (1Vp-p for each test tone) shows
that the two-tone intermodulation intercept has improved to
40dBm versus the 35dBm shown in the Typical Performance Curves, giving a 72dBc SFDR for the two 4dBm test
tones at the load .
The OPA686 provides a very low input noise voltage while
requiring a low 12mA quiescent current. To take full advantage of this low input noise, careful attention to the other
possible noise contributors is required. Figure 7 shows the
op amp noise analysis model with all the noise terms
included. In this model, all the noise terms are taken to be
noise voltage or current density terms in either nV/√Hz or
pA/√Hz.
ENI
EO
OPA686
RS
IBN
ERS
RF
√ 4kTRS
DESIGN-IN TOOLS
DEMONSTRATION BOARDS
Two PC boards are available to assist in the initial evaluation
of circuit performance using the OPA686 in its two package
styles. Both of these are available free as an unpopulated PC
board delivered with descriptive documentation. The summary information for these boards is shown in the table
below.
PRODUCT
PACKAGE
BOARD
PART
NUMBER
OPA686U
OPA686N
8-Pin SO-8
5-Lead SOT23-5
DEM-OPA68xU
DEM-OPA6xxN
LITERATURE
REQUEST
NUMBER
MKT-351
MKT-348
IBI
RG
4kT
RG
√ 4kTRF
4kT = 1.6E –20J
at 290°K
FIGURE 7. Op Amp Noise Analysis Model.
The total output spot noise voltage can be computed as the
square root of the squared contributing terms to the output
noise voltage. This computation adds all the contributing
noise powers at the output by superposition, then takes the
square root to get back to a spot noise voltage. Equation 1
shows the general form for this output noise voltage using
the terms shown in Figure 7.
Contact the Burr-Brown applications support line to request
any of these boards.
Equation 1
EO =
MACROMODELS AND APPLICATIONS SUPPORT
Computer simulation of circuit performance using SPICE is
often useful when analyzing the performance of analog
circuits and systems. This is particularly true for video and
RF amplifier circuits where parasitic capacitance and inductance can have a major effect on circuit performance. A
SPICE model for the OPA686 is available through either the
Burr-Brown Internet web page (http://www.burr-brown.com)
or as one model on a disk from the Burr-Brown Applications
department (1-800-548-6132). The Applications department
(E
NI
2
)
+ ( I BN R S ) + 4kTR S NG 2 + ( I BI R F ) + 4kTR F NG
2
2
Dividing this expression by the noise gain (NG = 1+RF/RG)
will give the equivalent input-referred spot noise voltage at
the non-inverting input as shown in Equation 2.
Equation 2
I R 2 4kTR F
2
E N = E NI 2 + ( I BN R S ) + 4kTR S +  BI F  +
 NG 
NG
®
11
OPA686
capacitive load is placed directly on the output pin. When
the amplifier’s open-loop output resistance is considered,
this capacitive load introduces an additional pole in the
signal path that can decrease the phase margin. Several
external solutions to this problem have been suggested.
When the primary considerations are frequency response
flatness, pulse response fidelity and/or distortion, the simplest and most effective solution is to isolate the capacitive
load from the feedback loop by inserting a series isolation
resistor between the amplifier output and the capacitive
load. This does not eliminate the pole from the loop response, but rather shifts it and adds a zero at a higher
frequency. The additional zero acts to cancel the phase lag
from the capacitive load pole, thus increasing the phase
margin and improving stability.
Inserting high resistor values into Eq. 2 can quickly dominate the total equivalent input referred noise. A 105Ω source
impedance on the non-inverting input will add a Johnson
voltage noise term equal to that of the amplifier itself. As a
simplifying constraint, set RG = RS in Eq. 2 and assume an
RS/2 source impedance at the non-inverting input (where RS
is the signal’s source impedance with another matching RS
to ground on the non-inverting input). This results in Eq. 3,
where NG > 10 has been assumed to further simplify the
expression.
Equation 3
EN =
( E NI )2 + 45 ( I BR S )2 + 4kT 
3R S 
2 
Evaluating this expression for RS = 50Ω will give a total
equivalent input noise of 1.7nV/√Hz. Note that the NG has
dropped out of this expression. This is valid only for NG > 10
as will typically be required by stability considerations.
The Typical Performance Curves show the recommended
RS vs Capacitive Load and the resulting frequency response
at the load. Parasitic capacitive loads greater than 2pF can
begin to degrade the performance of the OPA686. Long PC
board traces, unmatched cables, and connections to multiple
devices can easily cause this value to be exceeded. Always
consider this effect carefully, and add the recommended
series resistor as close as possible to the OPA686 output pin
(see Board Layout Guidelines).
FREQUENCY RESPONSE CONTROL
Voltage feedback op amps exhibit decreasing closed-loop
bandwidth as the signal gain is increased. In theory, this
relationship is described by the Gain Bandwidth Product
(GBP) shown in the specifications. Ideally, dividing GBP by
the non-inverting signal gain (also called the Noise Gain, or
NG) will predict the closed-loop bandwidth. In practice, this
only holds true when the phase margin approaches 90°, as it
does in high gain configurations. At low gains (increased
feedback factor), most high speed amplifiers will exhibit a
more complex response with lower phase margin. The
OPA686 is compensated to give a maximally flat 2nd-order
Butterworth closed-loop response at a non-inverting gain of
+10 (Figure 1). This results in a typical gain of +10 bandwidth of 250MHz, far exceeding that predicted by dividing
the 1600MHz GBP by 10. Increasing the gain will cause the
phase margin to approach 90° and the bandwidth to more
closely approach the predicted value of (GBP/NG). At a gain
of +40, the OPA686 will show the 40MHz bandwidth
predicted using the simple formula and the typical GBP of
1600MHz.
The criterion for setting this RS resistor is a maximum
bandwidth, flat frequency response at the load. For the
OPA686 operating in a gain of +10, the frequency response
at the output pin is very flat to begin with, allowing relatively
small values of RS to be used for low capacitive loads. As the
signal gain is increased, the unloaded phase margin will also
increase. Driving capacitive loads at higher gains will require lower RS values than those shown for a gain of +10.
DISTORTION PERFORMANCE
The OPA686 is capable of delivering an exceptionally low
distortion signal at high frequencies over a wide range of
gains. The distortion plots in the Typical Performance Curves
show the typical distortion under a wide variety of conditions. Most of these plots are limited to 110dB dynamic
range. The OPA686’s distortion, driving a 500Ω, load does
not rise above –90dBc until either the signal level exceeds
2.0Vp-p and/or the fundamental frequency exceeds 5MHz.
Distortion in the audio band is < –120dBc.
Inverting operation offers some interesting opportunities to
increase the available GBP. When the source impedance is
matched by the gain resistor (Figure 2), the signal gain is
(1+RF/RG) while the noise gain for bandwidth purposes is
(1 + RF/2RG). This cuts the noise gain almost in half, increasing the minimum stable gain for inverting operation under
these condition to –12 and the equivalent GBP to 3.2GHz.
Generally, until the fundamental signal reaches very high
frequencies or powers, the 2nd harmonic will dominate the
distortion with negligible a 3rd harmonic component. Focusing then on the 2nd harmonic, increasing the load impedance
improves distortion directly. Remember that the total load
includes the feedback network; in the non-inverting configuration, this is sum of RF + RG, while in the inverting
configuration, it is just RF (Figures 1 and 2). Increasing
output voltage swing increases harmonic distortion directly.
A 6dB increase in output swing will generally increase the
2nd harmonic 12dB and the 3rd harmonic 18dB. Increasing
the signal gain will also increase the 2nd harmonic distortion. Again, a 6dB increase in gain will increase the 2nd and
3rd harmonic by approximately 6dB even with constant
DRIVING CAPACITIVE LOADS
One of the most demanding and yet very common load
conditions for an op amp is capacitive loading. Often, the
capacitive load is the input of an A/D converter, including
additional external capacitance which may be recommended
to improve A/D linearity. A high speed, high open-loop gain
amplifier like the OPA686 can be very susceptible to decreased stability and closed-loop response peaking when a
®
OPA686
12
bias current cancellation to the circuit of Figure 1 would be
to insert a 20Ω series resistor into the non-inverting input
from the 50Ω terminating resistor. When the 50Ω source
resistor is DC-coupled, this will increase the source resistances for the non-inverting input bias current to 45Ω. Since
this is now equal to the resistance looking out of the
inverting input (RF || RG), the circuit will cancel the gains for
the bias currents to the output leaving only the offset current
times the feedback resistor as a residual DC error term at the
output. Using the 453Ω feedback resistor, this output error
will now be less than ±0.9µA • 453Ω = ±0.4mV over the full
temperature range.
output power and frequency. Finally, the distortion increases
as the fundamental frequency increases due to the rolloff in
the loop gain with frequency. Conversely, the distortion will
improve going to lower frequencies down to the dominant
open-loop pole at approximately 100kHz. Starting from the
–82dBc 2nd harmonic for a 5MHz, 2Vp-p fundamental into
a 200Ω load at G = +10 (from the Typical Performance
Curves), the 2nd harmonic distortion for frequencies lower
than 100kHz will be approximately –82dBc – 20log(5MHz/
100kHz) = –116dBc.
The OPA686 has extremely low 3rd-order harmonic distortion. This also gives a high two-tone, 3rd-order
intermodulation intercept as shown in the Typical Performance Curves. This intercept curve is defined at the 50Ω
load when driven through a 50Ω matching resistor to allow
direct comparisons to RF MMIC devices. This matching
network attenuates the voltage swing from the output pin to
the load by 6dB. If the OPA686 drives directly into the input
of a high impedance device, such as an ADC, the 6dB
attenuation is not taken. Under these conditions, the intercept will increase by a minimum 6dBm. The intercept is
used to predict the intermodulation spurious for two, closelyspaced frequencies. If the two test frequencies, f1 and f2, are
specified in terms of average and delta frequency, fO =
(f1 + f2)/2 and ∆f = |f2 – f1|/2, the two 3rd-order, close-in
spurious tones will appear at fO ±3 • ∆f. The difference
between two equal test-tone power levels and these
intermodulation spurious power levels is given by
∆dBc = 2 • (IM3 – PO) where IM3 is the intercept taken from
the Typical Performance Curve and PO is the power level in
dBm at the 50Ω load for one of the two closely-spaced test
frequencies. For instance, at 5MHz the OPA686 at a gain of
+10 has an intercept of 48dBm at a matched 50Ω load. If the
full envelope of the two frequencies needs to be 2Vp-p, this
requires each tone to be 4dBm. The 3rd-order intermodulation
spurious tones will then be 2 • (48 – 4) = 88dBc below the
test-tone power level (–84dBm). If this same 2Vp-p, twotone envelope were delivered directly into the input of an
ADC—without the matching loss or the loading of the 50Ω
network—the intercept would increase to at least 54dBm.
With the same signal and gain conditions, but now driving
directly into a light load, the spurious tones will then be at
least 2 • (54 – 4) = 100dBc below the 4dBm test-tone power
levels centered on 5MHz.
A fine-scale, output offset null, or DC operating point
adjustment, is often required. Numerous techniques are
available for introducing a DC offset control into an op amp
circuit. Most of these techniques eventually reduce to setting
up a DC current through the feedback resistor. One key
consideration to selecting a technique is to insure that it has
a minimal impact on the desired signal path frequency
response. If the signal path is intended to be non-inverting,
the offset control is best applied as an inverting summing
signal to avoid interaction with the signal source. If the
signal path is intended to be inverting, applying the offset
control to the non-inverting input can be considered. For a
DC-coupled inverting input signal, this DC offset signal will
set up a DC current back into the source that must be
considered. An offset adjustment placed on the inverting op
amp input can also change the noise gain and frequency
response flatness. Figure 8 shows one example of an offset
adjustment for a DC-coupled signal path that will have
minimum impact on the signal frequency response. In this
case, the input is brought into an inverting gain resistor with
the DC adjustment an additional current summed into the
inverting node. The resistor values setting this offset adjustment are much larger than the signal path resistors. This will
insure that this adjustment has minimal impact on the loop
gain and hence, the frequency response.
+5V
Supply Decoupling
Not Shown
0.1µF
48Ω
OPA686
VO
–5V
DC ACCURACY AND OFFSET CONTROL
+5V
The OPA686 can provide excellent DC signal accuracy due
to its high open-loop gain, high common-mode rejection,
high power supply rejection, and low input offset voltage
and bias current offset errors. To take full advantage of its
low ±1.5mV input offset voltage, careful attention to input
bias current cancellation is also required. The low noise
input stage of the OPA686 has a relatively high input bias
current (10µA typical into the pins) but with a very close
match between the two input currents—typically ±100nA
input offset current. The total output offset voltage may be
reduced considerably by matching the source impedances
looking out of the two inputs. For example, one way to add
RG
50Ω
RF
1kΩ
VI
5kΩ
20kΩ
±200mV Output Adjustment
10kΩ
0.1µF
5kΩ
VO
VI
=–
RF
RG
= –20
–5V
FIGURE 8. DC-Coupled, Inverting Gain of –20, with
Output Offset Adjustment.
®
13
OPA686
THERMAL ANALYSIS
Surface-mount resistors work best and allow a tighter overall layout. Metal-film and carbon composition, axially-leaded
resistors can also provide good high frequency performance.
Again, keep their leads and PC board trace length as short as
possible. Never use wirewound type resistors in a high
frequency application. Since the output pin and inverting
input pin are the most sensitive to parasitic capacitance,
always position the feedback and series output resistor, if
any, as close as possible to the output pin. Other network
components, such as non-inverting input termination resistors, should also be placed close to the package. Where
double-side component mounting is allowed, place the feedback resistor directly under the package on the other side of
the board between the output and inverting input pins. Even
with a low parasitic capacitance shunting the external resistors, excessively high resistor values can create significant
time constants that can degrade performance. Good axial
metal-film or surface-mount resistors have approximately
0.2pF in shunt with the resistor. For resistor values > 1.5kΩ,
this parasitic capacitance can add a pole and/or a zero below
500MHz that can effect circuit operation. Keep resistor
values as low as possible consistent with load driving considerations. It has been suggested here that a good starting
point for design would be set the RG be set to 50Ω. Doing
this will automatically keep the resistor noise terms low, and
minimize the effect of their parasitic capacitance.
The OPA686 will not require heatsinking or airflow in most
applications. Maximum desired junction temperature will
set the maximum allowed internal power dissipation as
described below. In no case should the maximum junction
temperature be allowed to exceed +175°C.
Operating junction temperature (TJ) is given by TA + PD •
θJA. The total internal power dissipation (PD) is the sum of
quiescent power (PDQ) and additional power dissipated in
the output stage (PDL) to deliver load power. Quiescent
power is simply the specified no-load supply current times
the total supply voltage across the part. PDL will depend on
the required output signal and load but would, for a grounded
resistive load, be at a maximum when the output is fixed at
a voltage equal to 1/2 either supply voltage (for equal bipolar
supplies). Under this worst-case condition, PDL = VS2/(4 •
RL) where RL includes feedback network loading.
Note that it is the power in the output stage and not in the
load that determines internal power dissipation.
As a worst-case example, compute the maximum TJ using an
OPA686N (SOT23-5 package) in the circuit of Figure 1
operating at the maximum specified ambient temperature of
+85°C and driving a grounded 100Ω load at +2.5VDC.
PD = 10V (13.9mA) + 52/(4 • (100Ω || 500Ω)) = 214mW
Maximum TJ = +85°C + (0.21W • 150°C/W) = 117°C
d) Connections to other wideband devices on the board
may be made with short direct traces or through onboard transmission lines. For short connections, consider
the trace and the input to the next device as a lumped
capacitive load. Relatively wide traces (50mils to 100mils)
should be used, preferably with ground and power planes
opened up around them. Estimate the total capacitive load
and set RS from the plot of recommended RS vs Capacitive
Load. Low parasitic capacitive loads (< 5pF) may not need
an RS since the OPA686 is nominally compensated to
operate with a 2pF parasitic load. Higher parasitic capacitive
loads without an RS are allowed as the signal gain increases
(increasing the unloaded phase margin). If a long trace is
required, and the 6dB signal loss intrinsic to a doublyterminated transmission line is acceptable, implement a
matched impedance transmission line using microstrip or
stripline techniques (consult an ECL design handbook for
microstrip and stripline layout techniques). A 50Ω environment is normally not necessary on board, and in fact, a
higher impedance environment will improve distortion as
shown in the distortion versus load plots. With a characteristic board trace impedance defined based on board material
and trace dimensions, a matching series resistor into the
trace from the output of the OPA686 is used as well as a
terminating shunt resistor at the input of the destination
device. Remember also that the terminating impedance will
be the parallel combination of the shunt resistor and the
input impedance of the destination device; this total effective impedance should be set to match the trace impedance.
If the 6dB attenuation of a doubly-terminated transmission
line is unacceptable, a long trace can be series-terminated at
the source end only. Treat the trace as a capacitive load in
this case and set the series resistor value as shown in the plot
BOARD LAYOUT
Achieving optimum performance with a high frequency
amplifier like the OPA686 requires careful attention to
board layout parasitics and external component types. Recommendations that will optimize performance include:
a) Minimize parasitic capacitance to any AC ground for
all of the signal I/O pins. Parasitic capacitance on the
output and inverting input pins can cause instability: on the
non-inverting input, it can react with the source impedance
to cause unintentional bandlimiting. To reduce unwanted
capacitance, a window around the signal I/O pins should be
opened in all of the ground and power planes around those
pins. Otherwise, ground and power planes should be unbroken elsewhere on the board.
b) Minimize the distance (< 0.25") from the power
supply pins to high frequency 0.1µF decoupling capacitors. At the device pins, the ground and power plane layout
should not be in close proximity to the signal I/O pins. Avoid
narrow power and ground traces to minimize inductance
between the pins and the decoupling capacitors. The power
supply connections should always be decoupled with these
capacitors. Larger (2.2µF to 6.8µF) decoupling capacitors,
effective at lower frequency, should also be used on the
main supply pins. These may be placed somewhat farther
from the device and may be shared among several devices in
the same area of the PC board.
c) Careful selection and placement of external components will preserve the high frequency performance of
the OPA686. Resistors should be a very low reactance type.
®
OPA686
14
of RS vs Capacitive Load. This will not preserve signal
integrity as well as a doubly-terminated line. If the input
impedance of the destination device is low, there will be
some signal attenuation due to the voltage divider formed by
the series output into the terminating impedance.
+V CC
External
Pin
e) Socketing a high speed part like the OPA686 is not
recommended. The additional lead length and pin-to-pin
capacitance introduced by the socket can create an extremely troublesome parasitic network which can make it
almost impossible to achieve a smooth, stable frequency
response. Best results are obtained by soldering the OPA686
onto the board.
Internal
Circuitry
–V CC
FIGURE 9. Internal ESD Protection.
These diodes provide moderate protection to input overdrive
voltages above the supplies as well. The protection diodes
can typically support 30mA continuous current. Where higher
currents are possible (e.g., in systems with ±15V supply
parts driving into the OPA686), current-limiting series resistors should be added into the two inputs. Keep these resistor
values as low as possible since high values degrade both
noise performance and frequency response.
INPUT AND ESD PROTECTION
The OPA686 is built using a very high speed complementary bipolar process. The internal junction breakdown voltages are relatively low for these very small geometry devices. These breakdowns are reflected in the Absolute Maximum Ratings table. All device pins are protected with
internal ESD protection diodes to the power supplies as
shown in Figure 9.
®
15
OPA686