AD AD8042_06

Dual 160 MHz
Rail-to-Rail Amplifier
AD8042
CONNECTION DIAGRAM
Single AD8041 and quad AD8044 also available
Fully specified at +3 V, +5 V, and ±5 V supplies
Output swings to within 30 mV of either rail
Input voltage range extends 200 mV below ground
No phase reversal with inputs 0.5 V beyond supplies
Low power of 5.2 mA per amplifier
High speed and fast settling on 5 V
160 MHz, −3 dB bandwidth (G = +1)
200 V/μs slew rate
39 ns settling time to 0.1%
Good video specifications (RL = 150 Ω, G = +2)
Gain flatness of 0.1 dB to 14 MHz
0.02% differential gain error
0.04° differential phase error
Low distortion: −64 dBc worst harmonic @ 10 MHz
Drives 50 mA 0.5 V from supply rails
OUT1
1
8
+VS
–IN1
2
7
OUT2
+IN1
3
6
–IN2
–VS
4
5
+IN2
AD8042
01059-001
FEATURES
Figure 2. 8-Lead PDIP and 8-Lead SOIC_N
The output voltage swing extends to within 30 mV of each rail,
providing the maximum output dynamic range. Additionally, it
features gain flatness of 0.1 dB to 14 MHz while offering differential
gain and phase error of 0.04% and 0.06° on a single 5 V supply.
This makes the AD8042 useful for professional video electronics,
such as cameras, video switchers, or any high speed portable
equipment. The AD8042’s low distortion and fast settling make
it ideal for buffering single-supply, high speed analog-to-digital
converters (ADCs).
APPLICATIONS
The AD8042 offers a low power supply current of 12 mA
maximum and can run on a single 3.3 V power supply. These
features are ideally suited for portable and battery-powered
applications where size and power are critical.
Video switchers
Distribution amplifiers
A/D drivers
Professional cameras
CCD Imaging systems
Ultrasound equipment (multichannel)
GENERAL DESCRIPTION
The AD8042 is a low power voltage feedback, high speed amplifier
designed to operate on +3 V, +5 V, or ±5 V supplies. It has true
single-supply capability with an input voltage range extending
200 mV below the negative rail and within 1 V of the positive rail.
The wide bandwidth of 160 MHz along with 200 V/μs of slew
rate on a single 5 V supply make the AD8042 useful in many
general-purpose, high speed applications where single supplies
from +3.3 V to +12 V and dual power supplies of up to ±6 V are
needed. The AD8042 is available in 8-lead PDIP and SOIC_N
packages.
15
VS = 5V
G = +1
CL = 5pF
RL = 2kΩ TO 2.5V
12
CLOSED-LOOP GAIN (dB)
9
G = +1
RL = 2kΩ TO 2.5V
5.0V
2.5V
6
3
0
–3
–6
01059-003
–9
–12
0V
1V
1µs
01059-002
–15
1
10
100
500
FREQUENCY (MHz)
Figure 3. Frequency Response
Figure 1. Output Swing: Gain = −1, VS = +5 V
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
AD8042
TABLE OF CONTENTS
Features .............................................................................................. 1
Typical Performance Characteristics ..............................................7
Applications....................................................................................... 1
Overdrive Recovery ................................................................... 12
General Description ......................................................................... 1
Circuit Description .................................................................... 12
Connection Diagram ....................................................................... 1
Driving Capacitive Loads.......................................................... 12
Revision History ............................................................................... 2
Layout Considerations............................................................... 15
Specifications..................................................................................... 3
Outline Dimensions ....................................................................... 16
Absolute Maximum Ratings............................................................ 6
Ordering Guide .......................................................................... 16
Maximum Power Dissipation ..................................................... 6
ESD Caution.................................................................................. 6
REVISION HISTORY
3/06—Rev. C to Rev. D
Changes to Text Prior to Table 2..................................................... 4
8/04—Rev. B to Rev. C
Changes to Ordering Guide ............................................................ 5
Changes to Outline Dimensions................................................... 15
7/02—Rev. A to Rev. B
Changes to Specifications ................................................................ 2
Rev. D | Page 2 of 16
AD8042
SPECIFICATIONS
TA = 25°C, VS = 5 V, RL = 2 kΩ to 2.5 V, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth, VO < 0.5 V p-p
Bandwidth for 0.1 dB Flatness
Slew Rate
Full Power Response
Settling Time to 1%
Settling Time to 0.1%
NOISE/DISTORTION PERFORMANCE
Total Harmonic Distortion
Input Voltage Noise
Input Current Noise
Differential Gain Error (NTSC, 100 IRE)
Differential Phase Error (NTSC, 100 IRE)
Worst-Case Crosstalk
DC PERFORMANCE
Input Offset Voltage
Conditions
Min
Typ
G = +1
G = +2, RL = 150 Ω, RF = 200 Ω
G = –1, VO = 2 V step
VO = 2 V p-p
G = –1, VO = 2 V step
125
160
14
200
30
26
39
MHz
MHz
V/μs
MHz
ns
ns
–73
15
700
0.04
0.04
0.06
0.24
–63
dB
nV/√Hz
fA/√Hz
%
%
Degrees
Degrees
dB
130
fC = 5 MHz, VO = 2 V p-p, G = +2, RL = 1 kΩ
f = 10 kHz
f = 10 kHz
G = +2, RL = 150 Ω to 2.5 V
G = +2, RL = 75 Ω to 2.5 V
G = +2, RL = 150 Ω to 2.5 V
G = +2, RL = 75 Ω to 2.5 V
f = 5 MHz, RL = 150 Ω to 2.5 V
3
TMIN to TMAX
Offset Drift
Input Bias Current
12
1.2
TMIN to TMAX
Input Offset Current
Open-Loop Gain
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Current
Short-Circuit Current
Capacitive Load Drive
POWER SUPPLY
Operating Range
Quiescent Current (Per Amplifier)
Power Supply Rejection Ratio
OPERATING TEMPERATURE RANGE
RL = 1 kΩ
TMIN to TMAX
VCM = 0 V to 3.5 V
RL = 10 kΩ to 2.5 V
RL = 1 kΩ to 2.5 V
RL = 50 Ω to 2.5 V
TMIN to TMAX, VOUT = 0.5 V to 4.5 V
Sourcing
Sinking
G = +1
90
68
0.10 to 4.9
0.4 to 4.4
0.2
100
90
Rev. D | Page 3 of 16
72
−40
0.06
0.12
9
12
3.2
4.8
0.5
Unit
mV
mV
mV/°C
μA
μA
μA
dB
dB
300
1.5
−0.2 to +4
74
kΩ
pF
V
dB
0.03 to 4.97
0.05 to 4.95
0.36 to 4.45
50
90
100
20
V
V
V
mA
mA
mA
pF
3
VS– = 0 V to −1 V, or VS+ = +5 V to +6 V
Max
5.5
80
12
6.4
+85
V
mA
dB
°C
AD8042
TA = 25°C, VS = 3 V, RL = 2 kΩ to 1.5 V, unless otherwise noted
Table 2.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth, VO < 0.5 V p-p
Bandwidth for 0.1 dB Flatness
Slew Rate
Full Power Response
Settling Time to 1%
Settling Time to 0.1%
NOISE/DISTORTION PERFORMANCE
Total Harmonic Distortion
Input Voltage Noise
Input Current Noise
Differential Gain Error (NTSC, 100 IRE)
Differential Phase Error (NTSC, 100 IRE)
Worst-Case Crosstalk
DC PERFORMANCE
Input Offset Voltage
Conditions
Min
Typ
G = +1
G = +2, RL = 150 Ω, RF = 200 Ω
G = −1, VO = 2 V step
VO = 2 V p-p
G = −1, VO = 1 V step
120
140
11
170
25
30
45
MHz
MHz
V/μs
MHz
ns
ns
–56
16
500
0.10
0.10
0.12
0.27
–68
dB
nV/√Hz
fA/√Hz
%
%
Degrees
Degrees
dB
120
fC = 5 MHz, VO = 2 V p-p, G = −1, RL = 100 Ω
f = 10 kHz
f = 10 kHz
G = +2, RL = 150 Ω to 1.5 V, Input VCM = 1 V
RL = 75 Ω to 1.5 V, Input VCM = 1 V
G = +2, RL = 150 Ω to 1.5 V, Input VCM = 1 V
RL = 75 Ω to 1.5 V, Input VCM = 1 V
f = 5 MHz, RL = 1 kΩ to 1.5 V
3
TMIN to TMAX
Offset Drift
Input Bias Current
12
1.2
TMIN to TMAX
Input Offset Current
Open-Loop Gain
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Current
Short-Circuit Current
Capacitive Load Drive
POWER SUPPLY
Operating Range
Quiescent Current (Per Amplifier)
Power Supply Rejection Ratio
OPERATING TEMPERATURE RANGE
RL = 1 kΩ
TMIN to TMAX
VCM = 0 V to 1.5 V
RL = 10 kΩ to 1.5 V
RL = 1 kΩ to 1.5 V
RL = 50 Ω to 1.5 V
TMIN to TMAX, VOUT = 0.5 V to 2.5 V
Sourcing
Sinking
G = +1
90
66
0.1 to 2.9
0.3 to 2.6
0.2
100
90
Rev. D | Page 4 of 16
68
0
9
12
3.2
4.8
0.6
Unit
mV
mV
μV/°C
μA
μA
μA
dB
dB
300
1.5
–0.2 to +2
74
kΩ
pF
V
dB
0.03 to 2.97
0.05 to 2.95
0.25 to 2.65
50
50
70
17
V
V
V
mA
mA
mA
pF
3
VS– = 0 V to –1 V, or VS+ = +3 V to +4 V
Max
5.5
80
12
6.4
70
V
mA
dB
°C
AD8042
TA = 25°C, VS = ±5 V, RL = 2 kΩ to 0 V, unless otherwise noted.
Table 3.
Parameter
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth, VO < 0.5 V p-p
Bandwidth for 0.1 dB Flatness
Slew Rate
Full Power Response
Settling Time to 1%
Settling Time to 0.1%
NOISE/DISTORTION PERFORMANCE
Total Harmonic Distortion
Input Voltage Noise
Input Current Noise
Differential Gain Error (NTSC, 100 IRE)
Differential Phase Error (NTSC, 100 IRE)
Worst-Case Crosstalk
DC PERFORMANCE
Input Offset Voltage
Conditions
Min
Typ
G = +1
G = +2, RL = 150 Ω, RF = 200 Ω
G = −1, VO = 2 V step
VO = 2 V p-p
G = −1, VO = 2 V step
125
170
18
225
35
22
32
MHz
MHz
V/μs
MHz
ns
ns
–78
15
700
0.02
0.02
0.04
0.12
–63
dB
nV/√Hz
fA/√Hz
%
%
Degrees
Degrees
dB
145
fC = 5 MHz, VO = 2 V p-p, G = +2, RL = 1 kΩ
f = 10 kHz
f = 10 kHz
G = +2, RL = 150 Ω
G = +2, RL = 75 Ω
G = +2, RL = 150 Ω
G = +2, RL = 75 Ω
f = 5 MHz, RL = 150 Ω
3
TMIN to TMAX
Offset Drift
Input Bias Current
12
1.2
TMIN to TMAX
Input Offset Current
Open-Loop Gain
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Current
Short-Circuit Current
Capacitive Load Drive
POWER SUPPLY
Operating Range
Quiescent Current (Per Amplifier)
Power Supply Rejection Ratio
OPERATING TEMPERATURE RANGE
RL = 1 kΩ
TMIN to TMAX
90
VCM = –5 V to +3.5 V
RL = 10 kΩ
RL = 1 kΩ
RL = 50 Ω
TMIN to TMAX, VOUT = −4.5 V to +4.5 V
Sourcing
Sinking
G = +1
66
−4.8 to +4.8
−4 to +3.2
0.2
94
86
Rev. D | Page 5 of 16
68
−40
0.05
0.10
9.8
14
3.2
4.8
0.6
Unit
mV
mV
μV/°C
μA
μA
μA
dB
dB
300
1.5
−5.2 to +4
74
kΩ
pF
V
dB
−4.97 to +4.97
−4.9 to +4.9
−4.2 to +3.5
50
100
100
25
V
V
V
mA
mA
mA
pF
3
VS– = −5 V to −6 V, or VS+ = +5 V to +6 V
Max
6
80
12
7
+85
V
mA
dB
°C
AD8042
ABSOLUTE MAXIMUM RATINGS
Table 4.
Parameter
Supply Voltage
Internal Power Dissipation 1
8-Lead PDIP (N)
8-Lead SOIC_N (R)
Input Voltage (Common Mode)
Differential Input Voltage
Output Short-Circuit Duration
Storage Temperature Range (N, R)
Lead Temperature (Soldering 10 sec)
MAXIMUM POWER DISSIPATION
Rating
12.6 V
1.3 W
0.9 W
±VS ± 0.5 V
±3.4 V
Observe Power
Derating Curves
−65°C to +125°C
300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
The maximum power that can be safely dissipated by the
AD8042 is limited by the associated rise in junction
temperature. The maximum safe junction temperature for
plastic encapsulated devices is determined by the glass
transition temperature of the plastic—approximately 150°C.
Exceeding this limit temporarily can cause a shift in parametric
performance due to a change in the stresses exerted on the die
by the package.
Exceeding a junction temperature of 175°C for an extended
period can result in device failure.
While the AD8042 is internally short-circuit protected, this may
not be sufficient to guarantee that the maximum junction
temperature (150°C) is not exceeded under all conditions. To
ensure proper operation, it is necessary to observe the
maximum power derating curves.
2.0
1.5
TJ = 150°C
1.0
8-LEAD SOIC PACKAGE
0.5
0
–50 –40 –30 –20 –10
01059-004
Specification is for the device in free air:
8-Lead PDIP: θJA = 90°C/W
8-Lead SOIC_N: θJA = 155°C/W.
MAXIMUM POWER DISSIPATION (W)
8-LEAD PLASTIC-DIP PACKAGE
1
0
10
20
30
40
50
60
70
80
AMBIENT TEMPERATURE (°C)
Figure 4. Maximum Power Dissipation vs. Temperature
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. D | Page 6 of 16
90
AD8042
TYPICAL PERFORMANCE CHARACTERISTICS
100
100
VS = 5V
T = 25°C
140 PARTS, SIDE A & B
MEAN = –1.52mV
STD DEVIATION = 1.15
SAMPLE SIZE = 280
(140 AD8042S)
80
95
60
50
40
30
20
85
80
01059-005
75
10
0
90
–6
–5
–4
–3
–2
–1
0
1
2
3
4
5
70
6
01059-008
FREQUENCY
70
VS = 5V
T = 25°C
OPEN-LOOP GAIN (dB)
90
0
250
500
VOS (mV)
VS = 5V
MEAN = –12.6µV/°C
STD DEVIATION = 2.02µV/°C
SAMPLE SIZE = 60
25
1250
1500
1750
2000
100
VS = 5V
RL = 1kΩ
98
OPEN-LOOP GAIN (dB)
20
FREQUENCY
1000
Figure 8. Open-Loop Gain vs. RL to 2.5 V
Figure 5. Typical Distribution of VOS
30
750
LOAD RESISTANCE (Ω)
15
10
96
94
92
90
–18
–16
–14
–12
–10
–8
–6
–4
–2
88
0
01059-009
0
01059-006
5
86
–40
VOS DRIFT (µV/°C)
–20
0
20
40
60
80
TEMPERATURE (°C)
Figure 6. VOS Drift Over −40°C to +85°C
Figure 9. Open-Loop Gain vs. Temperature
0
VS = 5V
VCM = 0V
–0.2
100
VS = 5V
90
RL = 500Ω TO 2.5V
OPEN-LOOP GAIN (dB)
–0.6
–1.0
–1.2
–1.4
–1.6
–1.8
–2.0
–40 –30 –20 –10
0
10
20
30
40
50
60
70
80
80
70
RL = 50Ω TO 2.5V
60
50
90
40
TEMPERATURE (°C)
01059-010
–0.8
01059-007
INPUT BIAS CURRENT (µA)
–0.4
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
OUTPUT VOLTAGE (V)
Figure 7. IB vs. Temperature
Figure 10. Open-Loop Gain vs. Output Voltage
Rev. D | Page 7 of 16
4.5
5.0
AD8042
DIFFERENTIAL
GAIN ERROR (%)
100
0.02
VS = ±5V
G = +2
RL = 150Ω
0.01
0
30
–0.01
0.05
10
3
01059-011
1
1k
10k
100k
1M
10M
100M
0.02
0.01
–0.01
1G
VS = ±5V
G = +2
RL = 150Ω
0
0
10
20
FREQUENCY (Hz)
Figure 11. Input Voltage Noise vs. Frequency
40
50
60
0.6
VS = 3V, AV = –1,
RL = 100Ω TO 1.5V
–40
0.4
NORMALIZED GAIN (dB)
VS = 5V, AV = +1,
RL = 100Ω TO 2.5V
–70
–80
VS = 5V, AV = +2,
RL = 1kΩ TO 2.5V
VS = 5V, AV = +1,
RL = 1kΩ TO 2.5V
1
2
3
4
5
6
0.3
0.2
0.1
0
14MHz
–0.1
–0.3
–0.4
7 8 9 10
1
10
FUNDAMENTAL FREQUENCY (MHz)
120
VS = 5V
G = +2
RF = 200Ω
RL = 150Ω TO 2.5V
100
OPEN-LOOP GAIN (dB)
80
–50
10MHz
–60
5MHz
–70
–80
1MHz
–90
01059-013
–100
–110
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
500
Figure 15. 0.1 dB Gain Flatness
VS = 5V, G = +2,
RL = 1kΩ TO 2.5V
–40
100
FREQUENCY (MHz)
Figure 12. Total Harmonic Distortion
–30
100
–0.2
01059-012
–90
90
01059-015
–60
80
VS = 5V
G = +2
RF = 200Ω
RL = 150Ω TO 2.5V
0.5
VS = 5V, AV = +2,
RL = 100Ω TO 2.5V
–50
–100
WORST HARMONIC (dBc)
70
Figure 14. Differential Gain and Phase Errors
–30
TOTAL HARMONIC DISTORTION (dBc)
30
MODULATING RAMP LEVEL (IRE)
4.0
4.5
60
OUTPUT VOLTAGE (V p-p)
45
0
40
–45
20
0
PHASE
–90
–20
–135
–40
–180
–60
–225
–80
0.01
5.0
GAIN
0.1
1
10
100
FREQUENCY (MHz)
Figure 13. Worst Harmonic vs. Output Voltage
Figure 16. Open-Loop Gain and Phase vs. Frequency
Rev. D | Page 8 of 16
–270
500
PHASE (Degrees)
100
0.03
01059-016
10
VS = +5V
G = +2
RL = 150Ω TO 2.5V
0.04
01059-014
300
VS = +5V
G = +2
RL = 150Ω TO 2.5V
NTSC SUBCARRIER (3.579MHz)
0.03
DIFFERENTIAL
PHASE ERROR (Degrees)
INPUT VOLTAGE NOISE (nV/ Hz)
0.04
AD8042
10
8
6
T = +85°C
T = +25°C
2
0
T = –40°C
–2
–4
45
VS = +3V, 1%
40
VS = +5V, 0.1%
35
VS = ±5V, 0.1%
30
1
10
100
VS = +5V, 1%
25
01059-017
–8
VS = ±5V, 1%
20
0.5
500
1.0
FREQUENCY (MHz)
TEST CIRCUIT:
0
VS = +5V
RL AND CL TO 2.5V
COMMON-MODE REJECTION (dB)
VS = ±5V
6
4
2
0
–2
01059-018
–4
–6
1
10
100
1.02kΩ
INCM
–10
1.02kΩ
–20
OUT
1.02kΩ
–30
–40
–50
–60
–70
–80
–90
10k
500
100k
1M
500M
0.8
VS = 5V
G = +1
VS = 5V
10
OUTPUT SATURATION VOLTAGE (V)
RBT = 50Ω
RBT = 0Ω
RBT
VOUT
1
0.1
01059-019
OUTPUT RESISTANCE (Ω)
100M
Figure 21. Common-Mode Rejection (CMR) vs. Frequency
Figure 18. Closed-Loop Frequency Response vs. Supply
0.01
0.01
10M
FREQUENCY (Hz)
FREQUENCY (MHz)
100
VS = 5V
1.02kΩ
0.1
1
10
100
0.7
5V – VOH (+25°C)
5V – VOH (–55°C)
0.5
0.4
0.3
0.2
+VOL (+125°C)
+VOL (+25°C)
+VOL (–55°C)
0.1
0
500
FREQUENCY (MHz)
5V – VOH (+125°C)
0.6
0
5
10
15
20
25
30
35
40
45
LOAD CURRENT (mA)
Figure 22. Output Saturation Voltage vs. Load Current
Figure 19. Output Resistance vs. Frequency
Rev. D | Page 9 of 16
01059-022
CLOSED-LOOP GAIN (dB)
Figure 20. Settling Time
VS = +3V
RL AND CL TO 1.5V
8
2.0
01059-021
G = +1
CL = 5pF
RL = 2kΩ
10
1.5
BIPOLAR INPUT STEP (V)
Figure 17. Closed-Loop Frequency Response vs. Temperature
12
01059-020
–6
–8
VS = +3V, 0.1%
50
4
–10
G = –1
RL = 2kΩ TO MIDPOINT
CL = 5pF
55
SETTLING TIME (ns)
CLOSED-LOOP GAIN (dB)
60
VS = 5V
G = +1
CL = 5pF
RL = 2kΩ TO 2.5V
50
AD8042
12.0
50
VS = 5V
VOUT = 100mV STEP
VS = ±5V
11.5
G = +2
VS = +5V
10.5
OVERSHOOT (%)
SUPPLY CURRENT (mA)
40
11.0
10.0
VS = +3V
9.5
30
20
G = +3
9.0
01059-023
8.0
–40 –30 –20 –10
0
10
20
30
40
50
60
70
80
0
90
01059-026
10
8.5
0
20
40
60
TEMPERATURE (°C)
Figure 23. Supply Current vs. Temperature
–10
4
NORMALIZED GAIN (dB)
5
–30
–PSRR
–50
+PSRR
–60
–70
180
200
VS = 5V
RF = 2kΩ
RL = 2kΩ to 2.5V
3
G = +2
2
1
0
G = +2
RF = 200Ω
–1
G = +10
01059-024
–2
–80
100k
1M
10M
100M
G = +5
–3
–4
500M
1
10
FREQUENCY (Hz)
Figure 27. Frequency Response vs. Closed-Loop Gain
–10
10
VS = ±5V
RL = 2kΩ
G = –1
9
–20
–30
7
–40
CROSSTALK (dB)
8
6
5
4
01059-025
–90
100
VOUT1
, RL = 150Ω TO 2.5V
VOUT2
–70
–80
10
VOUT1
, RL = 1kΩ TO 2.5V
VOUT2
–60
2
1
VS = 5V
VIN = 0.6V p-p
G = +2
RF = 1kΩ
–50
3
1
500
100
FREQUENCY (MHz)
Figure 24. PSRR vs. Frequency
OUTPUT VOLTAGE (V p-p)
160
01059-027
PSRR (dB)
–20
0
0.1
140
6
0
–90
10k
120
Figure 26. % Overshoot vs. Load Capacitance
VS = 5V
–40
100
VOUT2
, RL = 150Ω TO 2.5V
VOUT1
–100
VOUT2
, RL = 1kΩ TO 2.5V
VOUT1
–110
0.1
1
10
01059-028
10
80
LOAD CAPACITANCE (pF)
100
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 28. Crosstalk (Output-to-Output) vs. Frequency
Figure 25. Output Voltage Swing vs. Frequency
Rev. D | Page 10 of 16
200
AD8042
5V
4.770V
VS = 5V
G = –1
RL = 150Ω TO 2.5V
AV = 1
VS = 5V
VIN = 100mV p-p
CL = 5pF
RL = 1kΩ TO 2.5V
2.6V
4V
3V
2.5V
2V
0V
200µs
2.4V
01059-029
0.160V
0.5V
25mV
Figure 32. 100 mV Pulse Response, VS = +5 V
Figure 29. Output Swing with Load Reference to Supply Midpoint
5V
G = –1
RL = 2kΩ TO 1.5V
VS = 5V
G = –1
RL = 150Ω TO GND
4V
10ns
01059-032
1V
3.0V
4.59V
3V
1.5V
2V
0.5V
200µs
01059-030
0V
0V
0.035V
0.5V
Figure 30. Output Swing with Load Reference to Negative to Supply
4.5V
Figure 33. Rail-to-Rail Output Swing, VS = +3 V
AV = 2
VS = 5V
CL = 5pF
RL = 1kΩ TO 2.5V
VIN = 1V p-p
3.5V
1µs
01059-033
1V
AV = 1
VS = 3V
VIN = 100mV p-p
CL = 5pF
RL = 1kΩ TO 1.5V
1.6V
1.5V
2.5V
10ns
1.4V
01059-031
0.5V
0.5V
25mV
Figure 31. 1 V Pulse Response, VS = +5 V
10ns
Figure 34. 100 mV Pulse Response, VS = +3 V
Rev. D | Page 11 of 16
01059-034
1.5V
AD8042
OVERDRIVE RECOVERY
The AD8042’s rail-to-rail output range is provided by a
complementary common-emitter output stage. High output
drive capability is provided by injecting all output stage
predriver currents directly into the bases of the output devices
Q8 and Q36. Biasing of Q8 and Q36 is accomplished by I8 and
I5, along with a common-mode feedback loop (not shown).
This circuit topology allows the AD8042 to drive 40 mA of
output current with the outputs within 0.5 V of the supply rails.
Overdrive of an amplifier occurs when the output and/or input
range are exceeded. The amplifier must recover from this
overdrive condition. As shown in Figure 35, the AD8042
recovers within 30 ns from negative overdrive and within 25 ns
from positive overdrive.
On the input side, the device can handle voltages from 0.2 V
below the negative rail to within 1.2 V of the positive rail.
Exceeding these values does not cause phase reversal; however,
the input ESD devices do begin to conduct if the input voltages
exceed the rails by greater than 0.5 V.
5.0V
2.5V
50ns
Figure 35. Overdrive Recovery
CIRCUIT DESCRIPTION
The AD8042 is fabricated on Analog Devices proprietary eXtraFast Complementary Bipolar (XFCB) process, which enables
the construction of PNP and NPN transistors with similar fTs in
the 2 GHz to 4 GHz region. The process is dielectrically isolated
to eliminate the parasitic and latch-up problems caused by
junction isolation. These features allow the construction of high
frequency, low distortion amplifiers with low supply currents.
This design uses a differential output input stage to maximize
bandwidth and headroom (see Figure 36). The smaller signal
swings required on the first stage outputs (nodes S1P, S1N)
reduce the effect of nonlinear currents due to junction
capacitances and improve the distortion performance. With this
design, harmonic distortion of better than −77 dB @ 1 MHz
into 100 Ω with VOUT = 2 V p-p (gain = +2) on a single 5 V
supply is achieved.
1000
R26
Q4
I2
R39
Q51
R23 R27
Q31
Q7
Q17
Q21
SIP
Q2
VEE
C3
VOUT
Q27
C9
SIN
Q11
Q3
R5
Q8
Q24
R21
R3
I7
VEE
Q47
RS = 0Ω
100
RS = 20Ω
10
1
2
3
4
Figure 37. Capacitive Load Drive vs. Closed-Loop Gain
I5
Q39
Q23
Q22
VINN
C7
Q50
CL
CLOSED-LOOP GAIN (V/V)
I9
Q36
Q5
VEE
Q13
Q25
Q40
R15 R2
VINP
I3
I8
VCC
01059-036
I10
RS = 5Ω
RS
VCC
I1
VS = 5V
200mV STEP WITH 90% OVERSHOOT
01059-037
1V
The capacitive load drive of the AD8042 can be increased by
adding a low valued resistor in series with the load. Figure 37
shows the effects of a series resistor on capacitive drive for
varying voltage gains. As the closed-loop gain is increased, the
larger phase margin allows for larger capacitive loads with less
overshoot. Adding a series resistor with lower closed-loop gains
accomplishes the same effect. For large capacitive loads, the
frequency response of the amplifier is dominated by the roll-off
of the series resistor and capacitive load.
CAPACITIVE LOAD (pF)
G = +2
VS = 5V
VIN = 5V p-p
RL = 1kΩ TO 2.5V
01059-035
DRIVING CAPACITIVE LOADS
0V
Figure 36. Simplified Schematic
Rev. D | Page 12 of 16
5
AD8042
Single-Supply Composite Video Line Driver
The other extreme is for a video signal that is full white
everywhere. The blanking intervals and sync tips of such a
signal have negative going excursions in compliance with
composite video specifications. The combination of horizontal
and vertical blanking intervals limit such a signal to being at its
highest level (white) for only about 75% of the time.
The two op amps of an AD8042 can be configured as a singlesupply dual line driver for composite video. The wide signal
swing of the AD8042 enables this function to be performed
without using any type of clamping or dc restore circuit, which
can cause signal distortion.
Figure 38 shows a schematic for a circuit that is driven by a
single composite video source that is ac-coupled, level-shifted
and applied to both + inputs of the two amplifiers. Each op amp
provides a separate 75 Ω composite video output. To obtain
single-supply operation, ac coupling is used throughout. The
large capacitor values are required to ensure that there is
minimal tilting of the video signals due to their low frequency
(30 Hz) signal content. The circuit shown was measured to have
a differential gain of 0.06% and a differential phase of 0.06°.
The input is terminated in 75 Ω and ac-coupled via CIN to a
voltage divider that provides the dc bias point to the input.
Setting the optimal bias point requires some understanding of
the nature of composite video signals and the video
performance of the AD8042.
4.99kΩ
0.1µF
10µF
3
8
1
2
COMPOSITE
VIDEO IN
RF
1kΩ
75Ω
10µF
75Ω
COAX
1000µF
0.1µF
RT
75Ω
VOUT
RL
75Ω
RT
75Ω
VOUT
RL
75Ω
RG
1kΩ
100kΩ
220µF
5
7
6
1000µF
4
0.1µF
RG
1kΩ
01059-038
RF
1kΩ
220µF
Figure 38. Single-Supply Composite Video Line Driver Using AD8042
Signals of bounded peak-to-peak amplitude that vary in duty
cycle require larger dynamic swing capability than their peakto-peak amplitude after ac coupling. As a worst case, the
dynamic signal swing required approaches twice the peak-topeak value. The two bounding cases are for a duty cycle that is
mostly low, but occasionally goes high at a fraction of a percent
duty cycle and vice versa.
Composite video is not quite this demanding. One bounding
extreme is for a signal that is mostly black for an entire frame
but has a white (full intensity), minimum width spike at least
once per frame.
Some circuits use a sync tip clamp along with ac coupling to
hold the sync tips at a relatively constant level to lower the
amount of dynamic signal swing required. However, these
circuits can have artifacts, such as sync tip compression, unless
they are driven by sources with very low output impedance.
The AD8042 not only has ample signal swing capability to
handle the dynamic range required without using a sync tip
clamp but also has good video specifications such as differential
gain and differential phase when buffering these signals in an
ac-coupled configuration.
+5V
4.99kΩ
As a result of the duty cycle variations between the two extremes
presented above, a 1 V p-p composite video signal that is
multiplied by a gain of 2 requires about 3.2 V p-p of dynamic
voltage swing at the output for an op amp to pass a composite
video signal of arbitrary duty cycle without distortion.
To test this, the differential gain and differential phase were
measured for the AD8042 while the supplies were varied. As
the lower supply is raised to approach the video signal, the first
effect observed is that the sync tips become compressed before
the differential gain and differential phase are adversely
affected. Therefore, there must be adequate swing in the
negative direction to pass the sync tips without compression.
As the upper supply is lowered to approach the video, the
differential gain and differential phase was not significantly
affected until the difference between the peak video output
and the supply reached 0.6 V. Therefore, the highest video level
should be kept at least 0.6 V below the positive supply rail.
Therefore, it was found that the optimal point to bias the
noninverting input is at 2.2 V dc. Operating at this point, the
worst-case differential gain is measured at 0.06% and the worstcase differential phase is 0.06°.
The ac-coupling capacitors used in the circuit at first glance
appear quite large. A composite video signal has a lower frequency
band edge of 30 Hz. The resistances at the various ac coupling
points, especially at the output, are quite small. To minimize
phase shifts and baseline tilt, the large value capacitors are
required. For video system performance that is not to be of the
highest quality, the value of these capacitors can be reduced by a
factor of up to five with only a slightly observable change in the
picture quality.
Rev. D | Page 13 of 16
AD8042
Single-Ended-to-Differential Driver
The cable has a characteristic impedance of about 120 Ω. Each
driver output is back terminated with a pair of 60.4 Ω resistors
to make the source look like 120 Ω. The receive end is terminated
with 121 Ω, and the signal is measured differentially with a pair
of scope probes. One channel on the oscilloscope is inverted
and then the signals are added.
Using a cross-coupled, single-ended-to-differential converter,
the AD8042 makes a good general-purpose differential line
driver. This can be used for applications such as driving
Category-5 (CAT-5) twisted pair wire. Figure 39 shows a
configuration for a circuit that performs this function that
can be used for video transmission over a differential pair or
various data communication purposes.
The scope photo in Figure 40 shows a 10 MHz, 2 V p-p input
signal driving the circuit with 50 m of CAT-5 twisted pair wire.
+5V
0.1µF
49.9Ω
3
8
2 AMP1
1
RF
1kΩ
100
RB
1kΩ
6
VIN
60.4Ω
RA
1kΩ
AD8042
121Ω
VOUT
VOUT
RA
1kΩ
100Ω
90
50m
RB
1kΩ
5 AMP2
4
50ns
10
0%
7
60.4Ω
01059-040
RIN
1kΩ
200mV
0.1µF
01059-039
VIN
200mV
1V
10µF
10µF
–5V
Figure 40. Differential Driver Frequency Response
Single-Supply Differential A/D Driver
Figure 39. Single-Ended-to-Differential Twisted Pair Line Driver
Each of the AD8042’s op amps is configured as a unity gain
follower by the feedback resistors (RA). Each op amp output also
drives the other as a unity gain inverter via the two RBS, creating
a totally symmetrical circuit.
The single-ended-to-differential converter circuit is also useful
as a differential driver for video speed, single-ended, differential
input ADCs. Figure 41 is a schematic that shows such a circuit
differentially driving an AD9220, a 12-bit, 10-MSPS ADC.
+5V
If a resistor (RF) is connected from the output of Amp2 to the
+ input of Amp1, negative feedback is provided which closes
the loop. An input resistor (RI) makes the circuit look like a
conventional inverting op amp configuration with differential
outputs.
+5V
0.1µF
VIN
0.1µF
1kΩ
3
1kΩ
8
1
2
+5V
1kΩ
AD8042
6
2.49kΩ
0.1µF
1kΩ
1kΩ
+5V
+5V
1kΩ
+5V
0.1µF
15
DVDD
AVDD
The gain of this circuit from input to either output is ±RF/RI, or
the single-ended-to-differential gain is 2 × RF/RI. This gives the
circuit the advantage of being able to adjust its gain by changing
a single resistor.
AVDD
OTR
VINA
BIT1
7
VINB
5
BIT2
4
2.49kΩ
0.1µF
26
28
BIT3
0.1µF
CAPT
0.1µF
10/16
0.1µF
18
0.1µF
17
22
0.1µF
CLOCK
1
AD9220
BIT4
BIT5
BIT6
CAPB
BIT7
VREF
BIT8
SENSE
BIT9
BIT10
CML
BIT11
BIT12
CLK
14
13
12
11
10
9
8
7
6
5
4
3
2
REFCOM DVSS AVSS AVSS
19
27
25
16
Figure 41. AD8042 Differential Driver for the AD9220 12-Bit, 10-MSPS ADC
Rev. D | Page 14 of 16
01059-041
If the + input to Amp2 is grounded and a small positive signal is
applied to the + input of Amp1, the output of Amp1 is driven to
saturation in the positive direction and the input of Amp2 is
driven to saturation in the negative direction. This is similar to
the way a conventional op amp behaves without any feedback.
AD8042
Pin 5 is biased at 2.5 V by the voltage divider and bypassed.
This biases each output at 2.5 V. VIN is ac-coupled such that
VIN going positive makes VINA go positive and VINB go in
the negative direction. The opposite happens for a negative
going VIN.
2kΩ
3kΩ
6
VIN
232Ω
5
1/2
AD8042
2kΩ
3kΩ
2
3
0.001µF
ATT
2718AF
93DJ39
7
4
10
5
2
7
9
6
VOUT
1
1/2
AD8042
912Ω
1
1
0.0027µF
34Ω
2kΩ
2kΩ
2kΩ
2kΩ
3
2kΩ
1
249Ω
VREC
1/4
AD8044
0.001µF
9
3
7
2
6
5
Figure 43. HDSL Line Driver
4
8
LAYOUT CONSIDERATIONS
The specified high speed performance of the AD8042 requires
careful attention to board layout and component selection.
Proper RF design techniques and low-pass parasitic component
selection are necessary.
01059-042
VERTICAL SCALE (15dB/DIV)
2
01059-043
The circuit was tested with a 1 MHz input signal and clocked at
10 MHz. An FFT response of the digital output is shown in
Figure 42.
HARMONICS (dBc)
FUND FRQ 1000977
SMPL FRQ 10000000
THD
SNR
SINAD
SFDR
–82.00
71.13
70.79
–86.74
2ND
3RD
4TH
5TH
–88.34
–86.74
–99.26
–90.67
6TH
7TH
8TH
9TH
–99.47
–91.16
–97.25
–91.61
Figure 42. FFT of the AD9220 Output When Driven by the AD8042
HDSL Line Driver
High-bit-rate digital subscriber line (HDSL) is a popular means
of providing data communication at DS1 rates (1.544 Mbps)
over moderate distances via conventional telephone twisted pair
wires. In these systems, the transceiver at the customer’s end is
powered sometimes via the twisted pair from a power source at
the central office. Sometimes, it is required to raise the dc
voltage of the power source to compensate for IR drops in
long lines or lines with narrow gauge wires.
Because of this, it is highly desirable to keep the power
consumption of the customer’s transceiver as low as possible.
One means to realize significant power savings is to run the
transceiver from a ±5 V supply instead of the more
conventional ±12 V.
The high output swing and current drive capability of the
AD8042 make it ideally suited to this application. Figure 43
shows a circuit for the analog portion of an HDSL transceiver
using the AD8042 as the line driver.
The PCB should have a ground plane covering all unused
portions of the component side of the board to provide a low
impedance path. The ground plane should be removed from
the area near the input pins to reduce the stray capacitance.
Chip capacitors should be used for the supply bypassing. One
end should be connected to the ground plane and the other
within ⅛-inch of each power pin. An additional large (0.47 μF
to 10 μF) tantalum electrolytic capacitor should be connected in
parallel but not necessarily so close to supply current for fast,
large signal changes at the output.
The feedback resistor should be located close to the inverting
input pin to keep the stray capacitance at this node to a
minimum. Capacitance variations of less than 1 pF at the
inverting input significantly affect high speed performance.
Stripline design techniques should be used for long signal
traces (greater than approximately one inch). These should be
designed with a characteristic impedance of 50 Ω or 75 Ω and
be properly terminated at each end.
Rev. D | Page 15 of 16
AD8042
OUTLINE DIMENSIONS
0.400 (10.16)
0.365 (9.27)
0.355 (9.02)
8
1
5
4
0.280 (7.11)
0.250 (6.35)
0.240 (6.10)
0.100 (2.54)
BSC
0.210
(5.33)
MAX
0.150 (3.81)
0.130 (3.30)
0.115 (2.92)
0.060 (1.52)
MAX
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.015
(0.38)
MIN
0.015 (0.38)
GAUGE
PLANE
SEATING
PLANE
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.005 (0.13)
MIN
5.00 (0.1968)
4.80 (0.1890)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
PIN 1
0.430 (10.92)
MAX
8
4.00 (0.1574)
3.80 (0.1497) 1
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
0.070 (1.78)
0.060 (1.52)
0.045 (1.14)
5
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
6.20 (0.2440)
4 5.80 (0.2284)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
COPLANARITY
SEATING 0.31 (0.0122)
0.10
PLANE
0.50 (0.0196)
× 45°
0.25 (0.0099)
8°
0.25 (0.0098) 0° 1.27 (0.0500)
0.40 (0.0157)
0.17 (0.0067)
COMPLIANT TO JEDEC STANDARDS MS-001-BA
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 44. 8-Lead Plastic Dual In-Line Package [PDIP]
Narrow Body (N-8)
Dimensions shown in inches and (millimeters)
Figure 45. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body (R-8)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model
AD8042AN
AD8042AR
AD8042AR-REEL
AD8042AR-REEL7
AD8042ARZ 1
AD8042ARZ-REEL1
AD8042ARZ-REEL71
AD8042ACHIPS
1
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
8-Lead PDIP
8-Lead SOIC_N
8-Lead SOIC_N, 13" Reel
8-Lead SOIC_N, 7" Reel
8-Lead SOIC_N
8-Lead SOIC_N, 13" Reel
8-Lead SOIC_N, 7" Reel
DIE
Z = Pb-free part.
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C01059-0-3/06(D)
Rev. D | Page 16 of 16
Package Option
N-8
R-8
R-8
R-8
R-8
R-8
R-8