AD AD8041ARZ-REEL

160 MHz Rail-to-Rail
Amplifier with Disable
AD8041*
FEATURES
Fully Specified for +3 V, +5 V, and ⴞ5 V Supplies
Output Swings Rail to Rail
Input Voltage Range Extends 200 mV Below Ground
No Phase Reversal with Inputs 1 V Beyond Supplies
Disable/Power-Down Capability
Low Power of 5.2 mA (26 mW on 5 V)
High Speed and Fast Settling on 5 V:
160 MHz –3 dB Bandwidth (G = +1)
160 V/␮s Slew Rate
30 ns Settling Time to 0.1%
Good Video Specifications (RL = 150 ⍀, G = +2)
Gain Flatness of 0.1 dB to 30 MHz
0.03% Differential Gain Error
0.03ⴗ Differential Phase Error
Low Distortion
–69 dBc Worst Harmonic @ 10 MHz
Outstanding Load Drive Capability
Drives 50 mA 0.5 V from Supply Rails
Cap Load Drive of 45 pF
APPLICATIONS
Power Sensitive High Speed Systems
Video Switchers
Distribution Amplifiers
A/D Drivers
Professional Cameras
CCD Imaging Systems
Ultrasound Equipment (Multichannel)
Single-Supply Multiplexer
PRODUCT DESCRIPTION
The AD8041 is a low power voltage feedback, high speed amplifier designed to operate on +3 V, +5 V, or ± 5 V supplies. It has
true single-supply capability with an input voltage range extending
200 mV below the negative rail and within 1 V of the positive rail.
CONNECTION DIAGRAM
8-Lead PDIP, CERDIP and SOIC
8 DISABLE
NC 1
7 ⴙVS
–INPUT 2
ⴙINPUT 3
–VS 4
6 OUTPUT
AD8041
(Top View)
5 NC
NC = NO CONNECT
The output voltage swing extends to within 50 mV of each rail,
providing the maximum output dynamic range. Additionally, it
features gain flatness of 0.1 dB to 30 MHz while offering differential gain and phase error of 0.03% and 0.03° on a single 5 V
supply. This makes the AD8041 ideal for professional video
electronics such as cameras, video switchers, or any high speed
portable equipment. The AD8041’s low distortion and fast settling
make it ideal for buffering high speed A-to-D converters.
The AD8041 has a high speed disable feature useful for multiplexing or for reducing power consumption (1.5 mA). The
disable logic interface is compatible with CMOS or opencollector logic. The AD8041 offers a low power supply current
of 5.8 mA maximum and can run on a single 3 V power supply.
These features are ideally suited for portable and batterypowered applications where size and power are critical.
The wide bandwidth of 160 MHz along with 160 V/µs of slew
rate on a single 5 V supply make the AD8041 useful in many
general-purpose high speed applications where dual power
supplies of up to ± 6 V and single supplies from 3 V to 12 V are
needed. The AD8041 is available in 8-lead PDIP and SOIC
over the industrial temperature range of –40°C to +85°C.
2
VS = 5V
G = +2
RF = 400⍀
1
NORMALIZED GAIN (dB)
0
5V
2.5V
–1
–2
–3
–4
–5
–6
–7
0V
1V
200ns
–8
0
Figure 1. Output Swing: G = –1, VS = 5 V
*Protected by U.S.Patent No. 5,537,079.
20
40
60
FREQUENCY (MHz)
80
100
Figure 2. Frequency Response: G = +2, VS = 5 V
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective companies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© 2003 Analog Devices, Inc. All rights reserved.
AD8041–SPECIFICATIONS (@ T = 25ⴗC, V = 5 V, R = 2 k⍀ to 2.5 V, unless otherwise noted.)
A
S
L
Parameter
Conditions
Min
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth, VO < 0.5 V p-p
Bandwidth for 0.1 dB Flatness
Slew Rate
Full Power Response
Settling Time to 0.1%
Settling Time to 0.01%
G = +1
G = +2, RL = 150 Ω
G = –1, VO = 2 V Step
VO = 2 V p-p
G = –1, VO = 2 V Step
130
NOISE/DISTORTION PERFORMANCE
Total Harmonic Distortion
Input Voltage Noise
Input Current Noise
Differential Gain Error (NTSC)
Differential Phase Error (NTSC)
130
fC = 5 MHz, VO = 2 V p-p, G = +2, RL = 1 kΩ
f = 10 kHz
f = 10 kHz
G = +2, RL = 150 Ω to 2.5 V
G = +2, RL = 75 Ω to 2.5 V
G = +2, RL = 150 Ω to 2.5 V
G = +2, RL = 75 Ω to 2.5 V
DC PERFORMANCE
Input Offset Voltage
AD8041A
Typ
MHz
MHz
V/µs
MHz
ns
ns
–72
16
600
0.03
0.01
0.03
0.19
dB
nV/√Hz
fA/√Hz
%
%
Degrees
Degrees
2
10
1.2
TMIN to TMAX
Input Offset Current
Open-Loop Gain
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
Output Voltage Swing: RL = 10 kΩ
Output Voltage Swing: RL = 1 kΩ
Output Voltage Swing: RL = 50 Ω
Output Current
Short-Circuit Current
Capacitive Load Drive
POWER SUPPLY
Operating Range
Quiescent Current
Quiescent Current (Disabled)
Power Supply Rejection Ratio
DISABLE CHARACTERISTICS
Turn-Off Time
Turn-On Time
Off Isolation (Pin 8 Tied to –VS)
Off Voltage (Device Disabled)
On Voltage (Device Enabled)
RL = 1 kΩ
TMIN to TMAX
86
VCM = 0 V to 3.5 V
74
0.35 to 4.75
0.4 to 4.4
VOUT = 0.5 V to 4.5 V
Sourcing
Sinking
G = +1
0.2
95
90
VO = 2 V p-p @ 10 MHz, G = +2
RF = RL = 2 kΩ
RF = RL = 2 kΩ
RL = 100 Ω, f = 5 MHz, G = +2, RF = 1 kΩ
72
7
8
3.2
3.5
0.5
mV
mV
µV/°C
µA
µA
µA
dB
dB
160
1.8
–0.2 to +4
80
kΩ
pF
V
dB
0.05 to 4.95
0.1 to 4.9
0.3 to 4.5
50
90
150
45
V
V
V
mA
mA
mA
pF
3
VS = 0, +5 V, ± 1 V
Unit
160
30
160
24
35
55
TMIN to TMAX
Offset Drift
Input Bias Current
Max
5.2
1.4
80
120
230
70
<VS – 2.5
Open or +VS
12
5.8
1.7
V
mA
mA
dB
ns
ns
dB
V
V
Specifications subject to change without notice.
–2–
REV. B
AD8041
SPECIFICATIONS (@ T = 25ⴗC, V = 3 V, R = 2 k⍀ to 1.5 V, unless otherwise noted.)
A
S
L
Parameter
Conditions
Min
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth, VO < 0.5 V p-p
Bandwidth for 0.1 dB Flatness
Slew Rate
Full Power Response
Settling Time to 0.1%
Settling Time to 0.01%
G = +1
G = +2, RL = 150 Ω
G = –1, VO = 2 V Step
VO = 2 V p-p
G = –1, VO = 2 V Step
120
NOISE/DISTORTION PERFORMANCE
Total Harmonic Distortion
Input Voltage Noise
Input Current Noise
Differential Gain Error (NTSC)
Differential Phase Error (NTSC)
AD8041A
Typ
120
fC = 5 MHz, VO = 2 V p-p, G = –1, RL = 100 Ω
f = 10 kHz
f = 10 kHz
G = +2, RL = 150 Ω to 1.5 V, Input VCM = 1 V
G = +2, RL = 150 Ω to 1.5 V, Input VCM = 1 V
DC PERFORMANCE
Input Offset Voltage
MHz
MHz
V/µs
MHz
ns
ns
–55
16
600
0.07
0.05
dB
nV/√Hz
fA/√Hz
%
Degrees
2
10
1.2
TMIN to TMAX
Input Offset Current
Open-Loop Gain
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
Output Voltage Swing: RL = 10 kΩ
Output Voltage Swing: RL = 1 kΩ
Output Voltage Swing: RL = 50 Ω
Output Current
Short-Circuit Current
Capacitive Load Drive
POWER SUPPLY
Operating Range
Quiescent Current
Quiescent Current (Disabled)
Power Supply Rejection Ratio
DISABLE CHARACTERISTICS
Turn-Off Time
Turn-On Time
Off Isolation (Pin 8 Tied to –VS)
Off Voltage (Device Disabled)
On Voltage (Device Enabled)
RL = 1 kΩ
TMIN to TMAX
85
VCM = 0 V to 1.5 V
0.45 to 2.7
0.5 to 2.6
VOUT = 0.5 V to 2.5 V
Sourcing
Sinking
G = +1
0.2
94
89
VS = 0, +3 V, ± 0.5 V
VO = 2 V p-p @ 10 MHz, G = +2
RF = RL = 2 kΩ
RF = RL = 2 kΩ
RL = 100 Ω, f = 5 MHz, G = +2, RF = 1 kΩ
–3–
68
7
8
3.2
3.5
0.6
mV
mV
µV/°C
µA
µA
µA
dB
dB
160
1.8
–0.2 to +2
80
kΩ
pF
V
dB
0.05 to 2.95
0.1 to 2.9
0.25 to 2.75
50
70
120
40
V
V
V
mA
mA
mA
pF
3
Specifications subject to change without notice.
REV. B
72
Unit
150
25
150
20
40
55
TMIN to TMAX
Offset Drift
Input Bias Current
Max
5.0
1.3
80
90
170
70
<VS – 2.5
Open or +VS
12
5.6
1.5
V
mA
mA
dB
ns
ns
dB
V
V
AD8041
SPECIFICATIONS
(@ TA = 25ⴗC, VS = ⴞ5 V, RL = 2 k⍀ to 0 V, unless otherwise noted.)
Parameter
Conditions
Min
DYNAMIC PERFORMANCE
–3 dB Small Signal Bandwidth, VO < 0.5 V p-p
Bandwidth for 0.1 dB Flatness
Slew Rate
Full Power Response
Settling Time to 0.1%
Settling Time to 0.01%
G = +1
G = +2, RL = 150 Ω
G = –1, VO = 2 V Step
VO = 2 V p-p
G = –1, VO = 2 V Step
140
NOISE/DISTORTION PERFORMANCE
Total Harmonic Distortion
Input Voltage Noise
Input Current Noise
Differential Gain Error (NTSC)
Differential Phase Error (NTSC)
140
fC = 5 MHz, VO = 2 V p-p, G = +2, RL = 1 kΩ
f = 10 kHz
f = 10 kHz
G = +2, RL = 150 Ω
G = +2, RL = 75 Ω
G = +2, RL = 150 Ω
G = +2, RL = 75 Ω
DC PERFORMANCE
Input Offset Voltage
AD8041A
Typ
MHz
MHz
V/µs
MHz
ns
ns
–77
16
600
0.02
0.02
0.03
0.10
dB
nV/√Hz
fA/√Hz
%
%
Degrees
Degrees
2
10
1.2
TMIN to TMAX
Input Offset Current
Open-Loop Gain
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
Output Voltage Swing: RL = 10 kΩ
Output Voltage Swing: RL = 1 kΩ
Output Voltage Swing: RL = 50 Ω
Output Current
Short-Circuit Current
Capacitive Load Drive
POWER SUPPLY
Operating Range
Quiescent Current
Quiescent Current (Disabled)
Power Supply Rejection Ratio
DISABLE CHARACTERISTICS
Turn-Off Time
Turn-On Time
Off Isolation (Pin 8 Tied to –VS)
Off Voltage (Device Disabled)
On Voltage (Device Enabled)
RL = 1 kΩ
TMIN to TMAX
90
VCM = –5 V to +3.5 V
72
–4.45 to +4.6
–4.3 to +3.2
VOUT = –4.5 V to +4.5 V
Sourcing
Sinking
G = +1
0.2
99
95
VO = 2 V p-p @ 10 MHz, G = +2
RF = 2 kΩ
RF = 2 kΩ
RL = 100 Ω, f = 5 MHz, G = +2, RF = 1 kΩ
68
7
8
3.2
3.5
0.6
mV
mV
µV/°C
µA
µA
µA
dB
dB
160
1.8
–5.2 to +4
80
kΩ
pF
V
dB
–4.95 to +4.95
–4.8 to +4.8
–4.5 to +3.8
50
100
160
50
V
V
V
mA
mA
mA
pF
3
VS = –5 V, +5 V, ± 1 V
Unit
170
32
170
26
30
50
TMIN to TMAX
Offset Drift
Input Bias Current
Max
5.8
1.6
80
12
6.5
2.2
120
320
70
<VS – 2.5
Open or +VS
V
mA
mA
dB
ns
ns
dB
V
V
Specifications subject to change without notice.
–4–
REV. B
AD8041
ABSOLUTE MAXIMUM RATINGS 1
the stresses exerted on the die by the package. Exceeding a
junction temperature of 175°C for an extended period can result
in device failure.
Supply Voltage ............................................................ 12.6 V
Internal Power Dissipation2
PDIP Package (N) .................................................... 1.3 W
SOIC Package (R) .................................................... 0.9 W
Input Voltage (Common Mode) ...................................... ± VS
Differential Input Voltage ........................................... ± 3.4 V
Output Short-Circuit Duration
.......................................... Observe Power Derating Curves
Storage Temperature Range N, R .............. –65°C to +125°C
Operating Temperature Range (A Grade) ... –40°C to +85°C
Lead Temperature Range (Soldering 10 sec) ............... 300°C
While the AD8041 is internally short-circuit protected, this may
not be sufficient to guarantee that the maximum junction temperature (150°C) is not exceeded under all conditions. To
ensure proper operation, it is necessary to observe the maximum
power derating curves.
2.0
MAXIMUM POWER DISSIPATION (W)
8-LEAD PDIP PACKAGE
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
Specification is for the device in free air:
8-Lead PDIP Package: θJA = 90°C/W.
8-Lead SOIC Package: θJA = 155°C/W.
MAXIMUM POWER DISSIPATION
The maximum power that can be safely dissipated by the
AD8041 is limited by the associated rise in junction temperature.
The maximum safe junction temperature for plastic encapsulated
devices is determined by the glass transition temperature of the
plastic, approximately 150°C. Exceeding this limit temporarily
may cause a shift in parametric performance due to a change in
TJ = 150 ⴗC
1.5
1.0
8-LEAD SOIC PACKAGE
0.5
0
–50 –40 –30 –20 –10 0 10 20 30 40 50 60 70 80 90
AMBIENT TEMPERATURE (ⴗC)
Figure 3. Maximum Power Dissipation vs. Temperature
ORDERING GUIDE
Model
Temperature
Range
Package
Description
Package
Options
AD8041AN
AD8041AR
AD8041AR-REEL
AD8041AR-REEL7
AD8041ARZ-REEL1
5962-9683901MPA2
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–55°C to +125°C
8-Lead PDIP
8-Lead Plastic SOIC
13" Tape and Reel
7" Tape and Reel
13" Tape and Reel
8-Lead CERDIP
N-8
R-8
R-8
R-8
R-8
Q-8
NOTES
1
The Z indicates a lead-free product.
2
Refer to official DSCC drawing for tested specifications.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although the
AD8041 features proprietary ESD protection circuitry, permanent damage may occur on devices
subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended
to avoid performance degradation or loss of functionality.
REV. B
–5–
AD8041–Typical Performance Characteristics
100
30
VS = ⴞ2.5V
TA = 25ⴗC
91 PARTS
MEAN = +0.21
STD DEVIATION = 1.47
20
95
OPEN-LOOP GAIN (dB)
NUMBER OF PARTS IN BIN
25
15
10
90
85
80
75
5
0
70
–6
–5
–4
–3
–2
–1 0
1
VOS (mV)
2
3
4
5
6
0.20
250
500
750
1000 1250
1500
LOAD RESISTANCE (⍀)
1750
2000
100
MEAN = 0.02␮V/ⴗC
STD DEV = 2.87␮V/ⴗC
SAMPLE SIZE = 45
0.15
97
OPEN-LOOP GAIN (dB)
PROBABILITY DENSITY
0
TPC 4. Open-Loop Gain vs. RL to 25°C
TPC 1. Typical Distribution of VOS
0.10
0.05
0
–10
–7.5
–5
–2.5
0
2.5
VOS DRIFT (␮V/ⴗ C)
5
94
VS = 5V
RL = 1k⍀ TO 2.5V
91
88
85
–60
10
7.5
TPC 2. VOS Drift Over –40°C to +85°C
–40
–20
0
20
40
60
80
TEMPERATURE (ⴗC)
100
120
TPC 5. Open-Loop Gain vs. Temperature
2
100
VS = 5V
RL = 500⍀ TO 2.5V
VS = 5V
VCM = 0V
90
1.5
OPEN-LOOP GAIN (dB)
INPUT BIAS CURRENT (␮A)
VS = 5V
TA = 25ⴗC
1
0.5
80
RL = 50⍀ TO 2.5V
70
60
50
0
–45 –35 –25 –15 –5
5
15 25 35 45
TEMPERATURE (ⴗC)
55
65
75
40
85
TPC 3. IB vs. Temperature
0
0.5
1
1.5
2
2.5
3
3.5
OUTPUT VOLTAGE (V)
4
4.5
5
TPC 6. Open-Loop Gain vs. Output Voltage
–6–
REV. B
AD8041
100
50
0
10
100
1k
FREQUENCY (Hz)
5th
6th
7th
8th
9th 10th 11th
VS = 5V
G = +2
RL = 150⍀
1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th
DC OUTPUT LEVEL (100 IRE MAX)
VS = 5V, AV = 1,
RL = 100⍀ TO 2.5V
–70
VS = 5V, AV = 2,
RL = 1k⍀ TO 2.5V
–90
6.2
6.1
6.0
32.4MHz
5.9
5.8
5.7
5.6
VS = 5V, AV = 1,
RL = 1k⍀ TO 2.5V
5.5
2
3
4
5
6 7
FUNDAMENTAL FREQUENCY (MHz)
100
10
FREQUENCY (MHz)
1
8 9 10
500
TPC 11. 0.1 dB Gain Flatness
TPC 8. Total Harmonic Distortion
450
90
–30
10MHz
VS = 5V
RL = 2k⍀ TO 2.5V
CL = 5pF TO 2.5V
80
–40
–50
70
OPEN-LOOP GAIN (dB)
5MHz
–60
–70
–80
1MHz
–90
–100
VS = 5V
RL = 2k⍀ TO 2.5V
G = +2
–110
–120
–130
0.5
1
2.5
1.5
2
3
3.5
OUTPUT VOLTAGE (VP-P)
4
4.5
GAIN
270
60
180
50
90
0
40
30
PHASE
–90
20
–180
10
–270
0
–360
–10
0.01
5
360
0.1
10
FREQUENCY (MHz)
100
PHASE (ⴗC)
–80
VS = 5V
G = +2
RL = 150⍀ TO 2.5V
RF = 402⍀
6.3
CLOSED-LOOP GAIN (dB)
–50
1
WORST HARMONIC (dBc)
4th
VS = 5V
G = +2
RL = 150⍀ TO 2.5V
6.4
VS = 5V, AV = 2,
RL = 100⍀ TO 2.5V
–100
–450
500
TPC 12. Open-Loop Gain and Phase vs. Frequency
TPC 9. Worst Harmonic vs. Output Voltage
REV. B
1st 2nd 3rd
VS = 5V
G = +2
RL = 150⍀
6.5
VS = 3V, AV = –1,
RL = 100⍀ TO 1.5V
–40
–140
0
VS = 5V
G = +2
RL = 150⍀ TO 2.5V
TPC 10. Differential Gain and Phase Errors
–30
TOTAL HARMONIC DISTORTION (dBc)
0.035
0.030
0.025
0.020
0.015
0.010
0.005
0.000
–0.005
–0.010
100k
10k
TPC 7. Input Voltage Noise vs. Frequency
–60
DIFF GAIN (%)
150
0.035
0.030
0.025
0.020
0.015
0.010
0.005
0.000
–0.005
–0.010
DIFF PHASE (Degrees)
INPUT VOLTAAGE NOISE (nV/ Hz)
200
–7–
AD8041
50
5
VS = 5V
RL = 2k⍀ TO 2.5V
CL = 5pF
G = +1
4
2
G = –1
T = +125ⴗC
VS = 3V, 0.1%
40
T = +25ⴗC
1
0
TIME (ns)
CLOSED-LOOP GAIN (dB)
3
T = –55ⴗC
–1
VS = ⴞ5V, 0.1%
30
VS = 3V, 1%
–2
20
–3
VS = ⴞ5V, 1%
–4
–5
1
10
100
FREQUENCY (MHz)
10
0.5
500
TPC 13. Closed-Loop Frequency Response
vs. Temperature
2
–10
G = +1
RL = 2k⍀
CL = 5pF
4
3
–20
VS = 3V
RL AND CL TO 1.5V
–30
VS = 5V
RL AND CL TO 2.5V
2
0
VS = +3V AND ⴞ5V
–40
1
CMRR (dB)
CLOSED-LOOP GAIN (dB)
1.5
INPUT STEP (V p-p)
TPC 16. Settling Time vs. Input Step
5
VS = ⴞ5V
–1
–50
–60
–70
–80
–2
–3
–90
–4
–100
–5
1
1
10
100
FREQUENCY (MHz)
–110
0.01
500
0.1
1
10
FREQUENCY (MHz)
100
500
TPC 17. CMRR vs. Frequency
TPC 14. Closed-Loop Frequency Response vs. Supply
1000
OUTPUT SATURATION VOLTAGE (mV)
OUTPUT RESISTANCE (⍀)
100
G = +1
VS = 5V
10
1
0.1
0.01
0.01
0.1
1
10
FREQUENCY (MHz)
100
VS = 5V
C
5ⴗ
12
TPC 15. Output Resistance vs. Frequency
H
100
V
+5
–
VO
5ⴗC
, –5
H
O
V
–
ⴗC
+5V
+125
V L,
O
55ⴗC
V OL, –
10
0
0.001
500
,+
0.01
0.1
1
LOAD CURRENT (mA)
10
10
0
TPC 18. Output Saturation Voltage vs. Load Current
–8–
REV. B
AD8041
90
8
100k⍀
80
1k⍀
VS = 5V
RSERIES
7
CAPACITIVE LOAD (pF)
SUPPLY CURRENT (mA)
70
VS = ⴞ5V
6
VS = 5V
5
VS = 3V
4
CLOAD
VIN
60
50
20ⴗ PHASE
MARGIN
40
45ⴗ PHASE
MARGIN
30
20
3
10
2
–60
–40
–20
0
20
40
60
TEMPERATURE (ⴗC)
80
100
0
120
40
4
VS = 5V
–20
NORMALIZED OUTPUT (dB)
0
–PSRR
–40
–60
+PSRR
–80
–100
–120
50
G = +2
2
1
0
–1
G = +5
–2
G = +10
G = +2,
RF = 402⍀
–4
0.1
1
10
FREQUENCY (MHz)
100
–5
500
1
10
100
FREQUENCY (MHz)
500
TPC 23. Frequency Response vs. Closed-Loop Gain
TPC 20. PSRR vs. Frequency
10
1.600V
9
VIN = 0.1V p-p
RL = 2k⍀
VS = 3V
1.575V
8
1.550V
VS = ⴞ5V
RL = 2k⍀
7
G = +1
1.525V
6
5
1.500V
4
1.475V
3
1.450V
2
1.425V
50mV
1
10ns
1.400V
0
0.1
1
10
FREQUENCY (MHz)
100
1000
TPC 24. Pulse Response, VS = 3 V
TPC 21. Output Voltage Swing vs. Frequency
REV. B
60
VS = 5V
RL = 5k⍀ TO 2.5V
RF = 2k⍀
3
–3
–140
VOUT p-p (V)
20
30
40
SERIES RESISTANCE (⍀)
5
20
PSRR (dB)
10
TPC 22. Capacitive Load vs. Series Resistance
TPC 19. Supply Current vs. Temperature
–160
0.01
0
–9–
AD8041
5V
4.840V MAX
4V
VS = 5V
G = +1
RL = 2k⍀
VL = 5pF
2.60V
RL = 150⍀ TO 2.5V
2.55V
3V
2.50V
2V
2.45V
1V
2.40V
0.111V MIN
50mV
200␮s
1V
40ns
0V
TPC 27. 100 mV Step Response, VS = 5 V, G = +1
a.
3.0V
5V
4.741V MAX
VIN = 3V p-p
f = 0.1MHz
RL = 2k⍀
VS = 3V
G = –1
2.5V
4V
RL = 150⍀ TO GND
2.0V
3V
1.5V
2V
1.0V
1V
0.5V
1V
0.043V MIN
500mV
200␮s
2␮s
0V
0V
b.
TPC 25. Output Swing vs. Load Reference Voltage,
VS = 5 V, G = –1
TPC 28. Output Swing, VS = 3 V, VIN = 3 V p-p
3.0V
4.5V
VS = 5V
G = +2
RL = 2k⍀
VIN = 1V p-p
3.5V
VIN = 2.8V p-p
f = 0.8MHz
RL = 2k⍀
VS = 3V
G = –1
2.5V
2.0V
1.5V
2.5V
1.0V
1.5V
0.5V
1V
500mV
40ns
2␮s
0V
0.5V
TPC 26. One Volt Step Response, VS = 5 V, G = +2
TPC 29. Output Swing, VS = 3 V, VIN = 2.8 V p-p
–10–
REV. B
AD8041
Capacitor C9. R1 is the output resistance of the input stage; gm
is the input transconductance. C7 and C9 provide Miller compensation for the overall op amp. The unity gain frequency will
occur at gm/C9. Solving the node equations for this circuit yields:
Overdrive Recovery
Overdrive of an amplifier occurs when the output and/or input
range are exceeded. The amplifier must recover from this overdrive condition. As shown in Figure 4, the AD8041 recovers
within 50 ns from negative overdrive and within 25 ns from
positive overdrive.
VOUT
=
Vi
5.0V
where
OUTPUT
INPUT
G = +2
VS = 5V
50mV
 g 

( sR1 [C 9 ( A2 + 1)] + 1) ×  s  m2  + 1
  C3 

A0 = gmgm2 R2 R1
A2 = gm2 R2
(Open-Loop Gain of Op Amp)
(Open-Loop Gain of Output Stage)
The first pole in the denominator is the dominant pole of the
amplifier and occurs at about 180 Hz. This equals the input
stage output impedance R1 multiplied by the Miller-multiplied
value of C9. The second pole occurs at the unity-gain bandwidth
of the output stage, which is 250 MHz. This type of architecture
allows more open-loop gain and output drive to be obtained
than a standard two-stage architecture would allow.
2.5V
0V
A0
40ns
Figure 4. Overdrive Recovery
Circuit Description
Output Impedance
The AD8041 is fabricated on Analog Devices’ proprietary
eXtra-Fast Complementary Bipolar (XFCB) process, which
enables the construction of PNP and NPN transistors with similar
fT in the 2 GHz to 4 GHz region. The process is dielectrically
isolated to eliminate the parasitic and latch-up problems caused
by junction isolation. These features allow the construction of
high frequency, low distortion amplifiers with low supply currents.
This design uses a differential output input stage to maximize
bandwidth and headroom (see Figure 5). The smaller signal
swings required on the first stage outputs (nodes S1P, S1N) reduce
the effect of nonlinear currents due to junction capacitances and
improve the distortion performance. With this design harmonic
distortion of better than –85 dB @ 1 MHz into 100 Ω with VOUT =
2 V p-p (Gain = +2) on a single 5 V supply is achieved.
The low frequency open-loop output impedance of the common
emitter output stage used in this design is approximately 6.5 kΩ.
While this is significantly higher than a typical emitter follower
output stage, when connected with feedback, the output impedance is reduced by the open-loop gain of the op amp. With
110 dB of open-loop gain, the output impedance is reduced
to less than 0.1 Ω. At higher frequencies, the output impedance
will rise as the open-loop gain of the op amp drops; however, the
output also becomes capacitive due to the integrator capacitors
C9 and C3. This prevents the output impedance from ever becoming excessively high (see TPC 15), which can cause stability
problems when driving capacitive loads. In fact, the AD8041
has excellent cap-load drive capability for a high frequency op
amp. TPC 22 demonstrates that the AD8041exhibits a 45°
margin while driving a 20 pF direct capacitive load. In addition,
running the part at higher gains will also improve the capacitive
load drive capability of the op amp.
The complementary common-emitter design of the output stage
provides excellent load drive without the need for emitter followers, thereby improving the output range of the device considerably with respect to conventional op amps. High output drive
capability is provided by injecting all output stage predriver
currents directly into the bases of the output devices Q8 and
Q36. Biasing of Q8 and Q36 is accomplished by I8 and I5,
along with a common-mode feedback loop (not shown). This
circuit topology allows the AD8041 to drive 50 mA of output
current with the outputs within 0.5 V of the supply rails.
VCC
I1
I2
I3
R39
Q4
Q25
Q51
I5
Q39
Q23
Q40
Q22
VEE
VINP
VINN
A “Nested Integrator” topology is used in the AD8041 (see
the small-signal schematic in Figure 6). The output stage can
be modeled as an ideal op amp with a single-pole response and
a unity-gain frequency set by transconductance gm2 and
VEE
Q13
C3
Q31
Q21
VOUT
Q27
C9
S1N
Q2
Q11
Q3
C7
VEE
R23 R27
Q7
Q17
S1P
I9
Q50
Q36
Q5
R15 R2
On the input side, the device can handle voltages from –0.2 V
below the negative rail to within 1.2 V of the positive rail. Exceeding these values will not cause phase reversal; however, the
input ESD devices will begin to conduct if the input voltages
exceed the rails by greater than 0.5 V.
REV. B
I10
R26
R5
Q8
Q24
R21
R3
I7
I8
Q47
VCC
Figure 5. AD8041 Simplified Schematic
–11–
AD8041
C9
VS = 5V
S1N
100
90
C3
gmVi
R1
R2
VOUT
gm2
S1P
10
gmVi
R1
0%
C7
1V
Figure 6. Small Signal Schematic
200ns
Figure 8. 2:1 Multiplexer Performance
Disable Operation
Single-Supply A/D Conversion
The AD8041 has an active-low disable pin, which can be used
to three-state the output of the part and also lower its supply
current. If the disable pin is left floating, the part is enabled and
will perform normally. If the disable pin is pulled to 2.5 V (min)
below the positive supply, output of the AD8041 will be disabled
and the nominal supply current will drop to less than 1.6 mA.
For best isolation, the disable pin should be pulled to as low a
voltage as possible; ideally, the negative supply rail.
Figure 9 shows the AD8041 driving the analog inputs of the
AD9050 in a dc-coupled system with single-ended signals. All
components are powered from a single 5 V supply. The AD820
is used to offset the ground referenced input signal to the level
required by the AD9050. The AD8041 is used to add in the offset
with the ground referenced input signal and buffer the input to
AD9050. The nominal input range of the AD9050 is 2.8 V
and 3.8 V (1 V p-p centered at 3.3 V). This circuit provides
40 MSPS analog-to-digital conversion on just 330 mW of power
while delivering 10-bit performance.
The disable pin on the AD8041 allows it to be configured as a 2:1
mux as shown in Figure 7 and can be used to switch many types of
high speed signals. Higher order multiplexers can also be built.
The break-before-make switching time is approximately 50 ns to
disable the output and 300 ns to enable the output.
1k⍀
5V
VIN
–0.5V TO +0.5V
5V
5V
1k⍀
10
AD8041
10␮F
2.8V – 3.8V
AD9050
9
CH0
5MHz
0.1␮F
7
3
50⍀
AD8041
2
5V
3.3V
6
G = +2
4
1k⍀
8
1k⍀
AD820
0.1␮F
330⍀
330⍀
50⍀
Figure 9. 10-Bit, 40 MSPS A/D Conversion
5V
10␮F
CH1
10MHz
AD8041
50⍀
2
330⍀
0
7
3
6
–10
G = +2
4
–20
8
330⍀
–30
–40
13
12
11
10
F1 = 4.9MHz
FUNDAMENTAL = 0.6dB
SECOND HARMONIC = 66.9dB
THIRD HARMONIC = 74.7dB
SNR = 55.2dB
NOISE FLOOR = – 86.1dB
ENCODE FREQUENCY = 40MHz
–50
–60
74HC04
Figure 7. 2:1 Multiplexer
–70
–80
–90
–100
Figure 10. FFT Output of Circuit in Figure 9
–12–
REV. B
AD8041
APPLICATIONS
RGB Buffer
Single-Supply Composite Video Line Driver
Figure 13 shows a schematic of a single-supply gain-of-two
composite video line driver. Since the sync tips of a composite
video signal extend below ground, the input must be ac-coupled
and shifted positively to provide signal swing during these negative excursions in a single-supply configuration.
The AD8041 can provide buffering of RGB signals that include
ground while operating from a single 3 V or 5 V supply.
The signals that drive an RGB monitor are usually supplied by
current output DACs that operate from a 5 V only supply. These
can triple DACs like the ADV7120 and ADV7122 from Analog
Devices or integrate into the graphics controller IC as in most
PCs these days.
During the horizontal blanking interval, the currents output
from the DACs go to zero and the RGB signals are pulled to
ground via the termination resistors. If more than one RGB
monitor is desired, it cannot simply be connected in parallel
because it will provide an additional termination. Therefore,
buffering must be provided before connecting a second monitor.
Since the RGB signals include ground as part of their dynamic
output range, it has previously been required to use a dualsupply op amp to provide this buffering. In some systems, this is
the only component that requires a negative supply, so it can be
quite inconvenient to incorporate this multiple monitor feature.
Figure 11 shows a schematic of one channel of a single-supply,
gain-of-two buffer for driving a second RGB monitor. No current is required when the amplifier output is at ground. The
termination resistor at the monitor helps pull the output down
at low voltage levels.
3V OR 5V
0.1␮F
10␮F
NC
R, G OR B
7
3
8
AD8041
75⍀
6
75⍀
4
2
1k⍀
75⍀
SECOND RGB
MONITOR
1k⍀
PRIMARY RGB
MONITOR
Figure 11. Single-Supply RGB Buffer
The input is terminated in 75 Ω and ac-coupled via CIN to a
voltage divider that provides the dc bias point to the input.
Setting the optimal bias point requires some understanding of
the nature of composite video signals and the video performance
of the AD8041.
Signals of bounded peak-to-peak amplitude that vary in duty
cycle require larger dynamic swing capability than their peak-topeak amplitude after ac coupling. As a worst case, the dynamic
signal swing required will approach twice the peak-to-peak value.
The two bounding cases are for a duty cycle that is mostly low,
but occasionally goes high at a fraction of a percent duty cycle
and vice versa.
Composite video is not quite this demanding. One bounding
extreme is for a signal that is mostly black for an entire frame
but has a white (full intensity), minimum width spike at least
once per frame.
The other extreme is for a video signal that is full white everywhere. The blanking intervals and sync tips of such a signal will
have negative going excursions in compliance with composite
video specifications. The combination of horizontal and vertical
blanking intervals limit such a signal to being at its highest level
(white) for only about 75% of the time.
As a result of the duty cycle variations between the two extremes
presented above, a 1 V p-p composite video signal that is multiplied by a gain of two requires about 3.2 V p-p of dynamic voltage
swing at the output for an op amp to pass a composite video
signal of arbitrary duty cycle without distortion.
Some circuits use a sync tip clamp along with ac coupling to
hold the sync tips at a relatively constant level in order to lower
the amount of dynamic signal swing required. However, these
circuits can have artifacts like sync tip compression unless they
are driven by sources with very low output impedance.
Figure 12 is an oscilloscope photo of the circuit in Figure 11
operating from a 3 V supply and driven by the blue signal of a
color bar pattern. Note that the input and output are at ground
during the horizontal blanking interval. The RGB signals are
specified to output a maximum of 700 mV peak. The output of
the AD8041 is 1.4 V with the termination resistors providing a
divide-by-two. The red and green signals can be buffered in the
same manner with duplication of this circuit.
5V
4.99k⍀
4.99k⍀
10␮F
0.1␮F
47␮F
COMPOSITE
VIDEO IN
3
75⍀
10k⍀
AD8041
2
VIN
5␮s
RG
1k⍀
100
90
75⍀
COAX
1000␮F
6
RT
75⍀
8
4
NC
500mV
10␮F
7
VOUT
RL
75⍀
0.1␮F
RF
1k⍀
220␮F
GND
Figure 13. Single-Supply Composite Video Line Driver
VOUT
GND
10
0%
500mV
Figure 12. 3 V, RGB Buffer
REV. B
The AD8041 not only has ample signal swing capability to
handle the dynamic range required without using a sync tip
clamp but also has good video specifications like differential
gain and differential phase when buffering these signals in an accoupled configuration.
–13–
AD8041
To test this, the differential gain and differential phase were
measured for the AD8041 while the supplies were varied. As the
lower supply is raised to approach the video signal, the first effect
to be observed is that the sync tips become compressed before
the differential gain and differential phase are adversely affected.
Thus, there must be adequate swing in the negative direction to
pass the sync tips without compression.
Referring to Figure 15, the green plus sync signal is output
from an ADV7120, a single-supply triple video DAC. Because
the DAC is single supply, the lowest level of the sync tip is at
ground or slightly above. The AD8041 is set for a gain of two to
compensate for the divide by two of the output terminations.
500mV
As the upper supply is lowered to approach the video, the differential gain and differential phase were not significantly adversely
affected until the difference between the peak video output and
the supply reached 0.6 V. Thus, the highest video level should
be kept at least 0.6 V below the positive supply rail.
Taking the above into account, it was found that the optimal
point to bias the noninverting input is at 2.2 V dc. Operating at
this point, the worst-case differential gain is measured at 0.06%
and the worst-case differential phase is 0.06°.
10
0%
500mV
The ac coupling capacitors used in the circuit at first glance
appear quite large. A composite video signal has a lower frequency band edge of 30 Hz. The resistances at the various ac
coupling points—especially at the output—are quite small. In
order to minimize phase shifts and baseline tilt, the large value
capacitors are required. For video system performance that is
not to be of the highest quality, the value of these capacitors can
be reduced by a factor of up to five with only a slightly observable change in the picture quality.
Sync Stripper
Some RGB monitor systems use only three cables total and
carry the synchronizing signals along with the green (G) signal
on the same cable. The sync signals are pulses that go in the
negative direction from the blanking level of the G signal.
In some applications like prior to digitizing component video
signals with A/D converters, it is desirable to remove or strip the
sync portion from the G signal. Figure 14 is a schematic of a
circuit using the AD8041 running on a single 5 V supply that
performs this function.
GREEN W/SYNC
GREEN W/OUT SYNC
5V
VBLANK +0.4
GROUND
0.1␮F
GROUND
7
3
VIN
75⍀
10␮F
75⍀
AD8041
2
6
4
75⍀
(MONITOR)
R1
1k⍀
10␮s
100
90
Figure 15. Single-Supply Sync Stripper
The reference voltage for R1 should be twice the dc blanking
level of the G signal. If the blanking level is at ground and the
sync tip is negative as in some dual-supply systems, then R1 can
be tied to ground. In either case, the output will have the sync
removed and have the blanking level at ground.
Layout Considerations
The specified high speed performance of the AD8041 requires
careful attention to board layout and component selection.
Proper RF design techniques and low-pass parasitic component
selection are necessary.
The PCB should have a ground plane covering all unused portions
of the component side of the board to provide a low impedance
path. The ground plane should be removed from the area near
the input pins to reduce the stray capacitance.
Chip capacitors should be used for the supply bypassing.
One end should be connected to the ground plane and the other
within 1/8 inch of each power pin. An additional large (0.47 µF
to 10 µF) tantalum electrolytic capacitor should be connected in
parallel, but not necessarily so close, to supply current for fast,
large signal changes at the output.
The feedback resistor should be located close to the inverting
input pin in order to keep the stray capacitance at this node to a
minimum. Capacitance variations of less than 1 pF at the inverting
input will significantly affect high speed performance.
Stripline design techniques should be used for long signal traces
(greater than about 1 inch). These should be designed with a
characteristic impedance of 50 Ω or 75 Ω and be properly terminated at each end.
R2
1k⍀
0.8V
(2X VBLANK)
Figure 14. Single-Supply Sync Stripper
–14–
REV. B
AD8041
OUTLINE DIMENSIONS
8-Lead Plastic Dual In-Line Package [PDIP]
(N-8)
8-Lead Standard Small Outline Package [SOIC]
(R-8)
Dimensions shown in inches and (millimeters)
Dimensions shown in millimeters and (inches)
0.375 (9.53)
0.365 (9.27)
0.355 (9.02)
8
1
5
4
5.00 (0.1968)
4.80 (0.1890)
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.100 (2.54)
BSC
0.180
(4.57)
MAX
0.150 (3.81)
0.130 (3.30)
0.110 (2.79)
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
4.00 (0.1574)
3.80 (0.1497)
0.295 (7.49)
0.285 (7.24)
0.275 (6.98)
0.015
(0.38)
MIN
5
1
4
1.27 (0.0500)
BSC
0.150 (3.81)
0.135 (3.43)
0.120 (3.05)
0.25 (0.0098)
0.10 (0.0040)
COPLANARITY
SEATING
0.10
PLANE
0.015 (0.38)
0.010 (0.25)
0.008 (0.20)
SEATING
PLANE
0.060 (1.52)
0.050 (1.27)
0.045 (1.14)
8
Dimensions shown in inches and (millimeters)
0.055 (1.40)
MAX
5
0.310 (7.87)
0.220 (5.59)
PIN 1
1
4
0.100 (2.54) BSC
0.320 (8.13)
0.290 (7.37)
0.405 (10.29) MAX
0.200 (5.08)
MAX
0.200 (5.08)
0.125 (3.18)
0.023 (0.58)
0.014 (0.36)
0.060 (1.52)
0.015 (0.38)
0.150 (3.81)
MIN
SEATING
0.070 (1.78) PLANE
0.030 (0.76)
15
0
0.015 (0.38)
0.008 (0.20)
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
REV. B
0.50 (0.0196)
ⴛ 45ⴗ
0.25 (0.0099)
8ⴗ
0.25 (0.0098) 0ⴗ 1.27 (0.0500)
0.40 (0.0157)
0.17 (0.0067)
COMPLIANT TO JEDEC STANDARDS MS-012AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
8-Lead Ceramic Dual In-Line Package [CERDIP]
(Q-8)
8
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
COMPLIANT TO JEDEC STANDARDS MO-095AA
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN
0.005 (0.13)
MIN
6.20 (0.2440)
5.80 (0.2284)
–15–
AD8041
Revision History
Location
Page
5/03—Data Sheet changed from REV. A to REV. B.
Updated OUTLINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4/01—Data Sheet changed from REV. 0 to REV. A.
Specifications changed DISABLE CHARACTERISTICS, Off Voltage (Device Disabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
–16–
REV. B
C01058–0–6/03(B)
Deleted all references to evaluation board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Universal