Product Preview MRFIC2408PP/D Rev. 0, 08/2002 MRFIC2408 2.4 GHz RF Power Amplifier for Bluetooth™ Applications (Scale 2:1) Package Information Plastic Package Case 1408 (QFN-12) Ordering Information Device Marking Package PRFIC2408 2408 QFN-12 The MRFIC2408 is a single chip RF Power Amplifier intended for 2.4 GHz ISM Band applications. It can be used to implement Bluetooth™ Class I operation and contains power control circuitry. • Power Supply Range: 2.7 to 3.6 V • Power Amplifier Enable/Disable Function • Over 20 dB of Power Control • Low Power Shutdown Mode VCC1 VCC2 RFin RFout Bias EN VPC Figure 1. Simplified Block Diagram This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice. © Motorola, Inc., 2002. All rights reserved. Table 1. Maximum Ratings Ratings Symbol Value Unit Supply Voltage VCC 6.0 V Storage Temperature Range Tstg -55 to 150 °C Operating Case Temperature Range TC -40 to 110 °C Input Signal (PA In) Pin 5.0 dBm NOTE: Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the limits in the Electrical Characteristics tables. Table 2. Electrical Characteristics (VCC = 3.0 V, RFin = 2.0 dBm, f = 2.45 GHz, TA = 25°C) Characteristic Conditions Symbol Min Typ Max Unit No RF, VEN = 3.0 V, VPC = 3.0 V ICCQ - 220 - mA No RF, VEN = 0 V, VPC = 3.0 V ICCS - 0.001 - mA Saturated Output Power VEN = 3.0 V, VPC = 3.0 V Pout - 23 - dBm Power Gain VEN = 3.0 V, VPC = 3.0 V GP - 21 - dB RFin = 2.0 dBm, VEN = 0 V, VPC = 3.0 V |S21|off 30 - - dB VEN = 3.0 V, VPC = 3.0 V fo - - -25 dB Quiescent Current Shut-Off Current Disable Isolation Harmonics (2f, 3f, 4f) NOTE: VEN = Enable Voltage and VPC = Power Control Voltage. EN 1 Gnd 2 Gnd 3 RFin VCC1 VPC 12 11 10 Gnd 4 5 6 Gnd Gnd Gnd 9 RFout/VCC2 8 RFout/VCC2 7 Gnd (Top View) Figure 2. Pin Connections 2 MRFIC2408 Product Preview MOTOROLA 3 PIN 1 INDEX AREA M A 2X 0.1 C G 0.1 C 1.0 1.00 0.8 0.75 3 0.05 C 4 (0.24) 0.05 0.00 2X C VIEW ROTATED 90° CLOCKWISE 0.1 C A B 8X 1.25 0.95 0.1 M C A B 0.05 M C 12X 0.30 0.18 10 DETAIL M PIN 1 INDEX 12 8X 4X 1 7 3 1.25 0.95 12X 0.1 C A B 0.065 0.015 0.65 0.40 0.5 DETAIL S (90°) 0.39 0.31 2X DETAIL M (0.25) NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. THE COMPLETE JEDEC DESIGNATOR FOR THIS PACKAGE IS: HF-PQFP-N. 4. COPLANARITY APPLIES TO LEADS, CORNER LEADS, AND DIE ATTACH PAD. VIEW M-M 2X 4X (45°) CORNER CONFIGURATION 4 8X PIN 1 BACKSIDE IDENTIFIER (0.741) DETAIL N N 12X (0.565) EXPOSED DIE ATTACH PAD 9 6 SEATING PLANE DETAIL G M 0.1 C B (0.5) 0.1 0.0 DETAIL S PIN 1 BACKSIDE IDENTIFIER Figure 3. Outline Dimensions for QFN-12, 3x3 mm (Case 1408-01, Issue O) MOTOROLA MRFIC2408 Product Preview 3 HOW TO REACH US: Information in this document is provided solely to enable system and software implementers to use Motorola products. There are no express or implied copyright licenses granted hereunder to USA/EUROPE/LOCATIONS NOT LISTED: design or fabricate any integrated circuits or integrated circuits based on the information in this Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217 1-303-675-2140 or 1-800-441-2447 document. JAPAN: for any particular purpose, nor does Motorola assume any liability arising out of the application or Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products use of any product or circuit, and specifically disclaims any and all liability, including without Motorola Japan Ltd.; SPS, Technical Information Center, 3-20-1, Minami-Azabu Minato-ku, Tokyo 106-8573 Japan 81-3-3440-3569 limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre, 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong 852-26668334 TECHNICAL INFORMATION CENTER: for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, 1-800-521-6274 HOME PAGE: http://www.motorola.com/semiconductors affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and the Stylized M Logo are registered in the U.S. Patent and Trademark Office. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc., under license. All other product or service names are the property of their respective owners. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. © Motorola, Inc. 2002 MRFIC2408PP/D