MAXIM MAX1873REEE

19-2099; Rev 0; 7/01
ILABLE
N KIT AVA
EVALUATIO
Simple Current-Limited Switch-Mode
Li+ Charger Controller
The low-cost MAX1873R/S/T provides all functions
needed to simply and efficiently charge 2-, 3-, or 4series lithium-ion cells at up to 4A or more. It provides a
regulated charging current and voltage with less than
±0.75% total voltage error at the battery terminals. An
external P-channel MOSFET operates in a step-down
DC-DC configuration to efficiently charge batteries in
low-cost designs.
The MAX1873R/S/T regulates the battery voltage and
charging current using two control loops that work
together to transition smoothly between voltage and
current regulation. An additional control loop limits current drawn from the input source so that AC adapter
size and cost can be minimized. An analog voltage output proportional to charging current is also supplied so
that an ADC or microcontroller can monitor charging
current.
The MAX1873 may also be used as an efficient currentlimited source to charge NiCd or NiMH batteries in multichemistry charger designs. The MAX1873R/S/T is
available in a space-saving 16-pin QSOP package. Use
the evaluation kit (MAX1873EVKIT) to help reduce
design time.
Features
♦ Low-Cost and Simple Circuit
♦ Charges 2-, 3-, or 4-Series Lithium-Ion Cells
♦ AC Adapter Input-Current-Limit Loop
♦ Also Charges Ni-Based Batteries
♦ Analog Output Monitors Charge Current
♦ ±0.75% Battery-Regulation Voltage
♦ 5µA Shutdown Battery Current
♦ Input Voltage Up to 28V
♦ 200mV Dropout Voltage/100% Duty Cycle
♦ Adjustable Charging Current
♦ 300kHz PWM Oscillator Reduces Noise
♦ Space-Saving 16-Pin QSOP
♦ MAX1873 Evaluation Kit Available to Speed
Designs
Ordering Information
TEMP. RANGE
PIN-PACKAGE
MAX1873REEE
-40°C to +85°C
16 QSOP
Notebook Computers
MAX1873SEEE
-40°C to +85°C
16 QSOP
Portable Internet Tablets
MAX1873TEEE
-40°C to +85°C
16 QSOP
Applications
PART
2-, 3-, or 4-cell Li+ Battery Pack Chargers
Typical Operating Circuit
6-, 9-, or 10-cell Ni Battery Pack Chargers
Hand-Held Instruments
Portable Desktop Assistants (PDAs)
Desktop Cradle Chargers
SYSTEM
LOAD
VIN 9V TO
28V
(9V MIN
FOR 2CELLS)
VH VL
Selector Guide
DCIN
CSSP
MAX1873
CSSN
PART
SERIES CELLS TO CHARGE
4V OUT PER
200mV ON RCS
MAX1873REEE
2-Cell Li+ or 5- or 6-cell Ni Battery
MAX1873SEEE
3-Cell Li+ or 7- or 9-cell Ni Battery
ICHG/EN
MAX1873TEEE
4-Cell Li+ 10-cell Ni Battery Packs
REF
IOUT
EXT
CSB
BATT
CCI
VADJ
Pin Configuration appears at end of data sheet.
CCS
GND
CCV
2- TO 4-CELL
Li+
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX1873
General Description
MAX1873
Simple Current-Limited Switch-Mode
Li+ Charger Controller
ABSOLUTE MAXIMUM RATINGS
CSSP, CSSN, DCIN to GND ...................................-0.3V to +30V
VL, ICHG/EN to GND................................................-0.3V to +6V
VH, EXT to DCIN.......................................................-6V to +0.3V
VH, EXT to GND ......................................(VDCIN + 0.3V) to -0.3V
EXT to VH .................................................................+6V to -0.3V
DCIN to VL..............................................................+30V to -0.3V
VADJ, REF, CCI, CCV, CCS,
IOUT to GND.............................................-0.3V to (VL + 0.3V)
BATT, CSB to GND.................................................-0.3V to +20V
CSSP to CSSN.......................................................-0.3V to +0.6V
CSB to BATT..........................................................-0.3V to +0.6V
VL Source Current ............................................................+50mA
VH Sink Current ................................................................+40mA
Continuous Power Dissipation (TA = +70°C)
16-Pin QSOP (derate 8.3mW/°C above +70°C..........+667mW
Operating Temperature Range
MAX1873_EEE ................................................-40°C to +85°C
Junction Temperature ..................................................... +150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) ................................ +300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VICHG/EN = VREF, VVADJ = VREF/2. MAX1873R: VBATT = VCSB = 8.4V;
MAX1873S: VBATT = VCSB = 12.6V; MAX1873T: VBATT = VCSB = 16.8V; TA = 0°C to +85°C. Typical values are at TA = +25°C, unless
otherwise noted.)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
28
V
4
7
mA
0.1
10
µA
0.175
V
0.38
V
INPUT SUPPLY AND REFERENCE
DCIN Input Voltage Range
DCIN Quiescent Supply Current
6
6.0V < VDCIN < 28V
DCIN ≤ BATT
DCIN to BATT Undervoltage Threshold
CSSP = DCIN, input falling
0.05
DCIN to BATT Undervoltage Threshold
CSSP = DCIN, input rising
0.22
VL Output Voltage
6.0V < VDCIN < 28V
5.15
VL Output Load Regulation
IVL = 0 to 3mA
REF Output Voltage
IREF = 21µA (200kΩ load)
REF Line Regulation
6.0V < VDCIN < 28V
REF Load Regulation
IREF = 0 to 1mA
4.179
5.40
5.65
V
15
50
mV
4.20
4.221
V
2
6
mV
22
65
ppm/V
6
13
mV
300
330
kHz
4
7
Ω
2.5
4.5
Ω
5.75
V
SWITCHING REGULATOR
PWM Oscillator Frequency
270
EXT Driver Source On-Resistance
EXT Driver Sink On-Resistance
VH Output Voltage
DCIN - VH, 6V < VDCIN <28V, IVH = 0 to 20mA
CSSN/CSSP Input Current
VCSSN/VCSSP = 28V, VDCIN = 28V
70
200
µA
CSSN/CSSP Off-State Leakage
VDCIN = VSSN/VCSSP = 18V, VBATT = VCSB = 18V
1.5
5
µA
ICHG/EN = 0 (charger disabled)
0.2
1
ICHG/EN = REF (charger enabled)
250
500
DCIN ≤ BATT (input power removed)
1.5
5
BATT, CSB Input Current
BATT, CSB Input Current
2
4.75
_______________________________________________________________________________________
µA
µA
Simple Current-Limited Switch-Mode
Li+ Charger Controller
(Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VICHG/EN = VREF, VVADJ = VREF/2. MAX1873R: VBATT = VCSB = 8.4V;
MAX1873S: VBATT = VCSB = 12.6V; MAX1873T: VBATT = VCSB = 16.8V; TA = 0°C to +85°C. Typical values are at TA = +25°C, unless
otherwise noted.)
PARAMETER
BATT Overvoltage Cutoff Threshold
MIN
TYP
MAX
2-cell version MAX1873R
CONDITIONS
10.45
11
11.55
3-cell version MAX1873S
15.675
16.5
17.325
17.575
18.5
19.425
7.898
7.958
8.018
4-cell version MAX1873T (Note 1)
MAX1873R
(2 Li+ cells)
Battery Regulation Voltage
MAX1873S
(3 Li+ cells)
MAX1873T
(4 Li+ cells)
BATT Undervoltage Threshold
VVADJ = 0
VVADJ = VREF/2
8.337
8.4
8.463
VVADJ = VREF (Note 1)
8.775
8.842
8.909
VVADJ = 0
11.847
11.937
12.027
VVADJ = VREF/2
12.505
12.6
12.695
VVADJ = VREF (Note 1)
13.163
13.263
13.363
VVADJ = 0
15.796
15.916
16.036
UNITS
V
V
VVADJ = VREF/2
16.674
16.8
16.926
VVADJ = VREF (Note 1)
17.551
17.684
17.817
MAX1873R
4.8
5.0
5.2
MAX1873S
7.2
7.5
7.8
MAX1873T
9.6
10
10.4
VICHG/EN = VREF
190
200
210
VICHG/EN = VREF/4
40
50
60
5
10
15
mV
6V < VCSSP < 28V
90
100
110
mV
Includes 50mV of hysteresis
500
600
700
mV
700
VREF
mV
For ICHG/20 trickle
charge
V
CURRENT SENSE
CSB to BATT Battery Current-Sense
Voltage
CSB to BATT Current-Sense Voltage
when VBATT < 2.5V per Cell
CSSP to CSSN Current-Sense Voltage
mV
CONTROL INPUTS/OUTPUTS
ICHG/EN Input Threshold
ICHG/EN Input Voltage Range For
Charge Current Adjustment
VADJ Input Current
VVADJ = VREF/2
-100
100
nA
ICHG/EN Input Current
VICHG/EN = VREF
-100
100
nA
0
VREF
V
VADJ Input Voltage Range
IOUT Voltage
Full scale
VCSB - VBATT = 200mV,
0 < IOUT < 500µA
3.6
25% scale
VCSB - VBATT = 50mV,
0 < IOUT < 500µA
0.9
1.0
1.1
Trickle charge
VCSB - VBATT = 10mV
75
200
325
No charge
current
VCSB - VBATT = 0,
IIOUT = sinking 20µA
40
70
90
4.0
4.4
V
mV
_______________________________________________________________________________________
3
MAX1873
ELECTRICAL CHARACTERISTICS (continued)
MAX1873
Simple Current-Limited Switch-Mode
Li+ Charger Controller
ELECTRICAL CHARACTERISTICS
(Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VICHG/EN = VREF, VVADJ = VREF/2. MAX1873R: VBATT = VCSB = 8.4V;
MAX1873S: VBATT = VCSB = 12.6V; MAX1873T: VBATT = VCSB = 16.8V; TA = -40°C to +85°C. Typical values are at TA = +25°C,
unless otherwise noted.)
PARAMETER
CONDITIONS
MIN
MAX
UNITS
6
28
V
7
mA
INPUT SUPPLY AND REFERENCE
DCIN Input Voltage Range
DCIN Quiescent Supply Current
6.0V < VDCIN < 28V
DCIN ≤ BATT
10
µA
DCIN to BATT Undervoltage Threshold
CSSP = DCIN, input falling
0.05
0.2
V
DCIN to BATT Undervoltage Threshold
CSSP = DCIN, input rising
0.22
0.38
V
VL Output Voltage
6.0V < VDCIN < 28V
5.15
5.65
V
VL Output Load Regulation
IVL = 0 to 3mA
50
mV
REF Output Voltage
IREF = 21µA (200kΩ load)
REF Line Regulation
6.0V < VDCIN < 28V
REF Load Regulation
IREF = 0 to 1mA
4.179
4.221
V
6
mV
65
ppm/V
13
mV
330
kHz
SWITCHING REGULATOR
PWM Oscillator Frequency
270
EXT Driver Source On-Resistance
EXT Driver Sink On-Resistance
VH Output Voltage
DCIN - VH, 6V < VDCIN <28V, IVH = 0 to 20mA
CSSN/CSSP Input Current
VCSSN/VCSSP = 28V, VDCIN = 28V
CSSN/CSSP Off-State Leakage
VDCIN = VSSN/VCSSP = 18V VBATT = VCSB = 18V
BATT, CSB Input Current
BATT, CSB Input Current
BATT Overvoltage Cutoff Threshold
ICHG/EN = 0 (charger disabled)
Ω
5.75
V
200
µA
5
µA
500
DCIN ≤ BATT (input power removed)
5
2-cell version MAX1873R
10.45
11.55
3-cell version MAX1873S
15.675
17.325
4-cell version MAX1873T (Note 1)
17.575
19.425
MAX1873S
(3 Li+ cells)
MAX1873T
(4 Li+ cells)
4
Ω
1
ICHG/EN = REF (charger enabled)
MAX1873R
(2 Li+ cells)
Battery Regulation Voltage
4.75
7
4.5
VVADJ = 0
7.898
8.018
VVADJ = VREF/2
8.337
8.463
VVADJ = VREF (Note 1)
8.775
8.909
VVADJ = 0
11.847
12.027
VVADJ = VREF/2
12.505
12.695
VVADJ = VREF (Note 1)
13.163
13.363
VVADJ = 0
15.796
16.036
VVADJ = VREF/2
16.674
16.926
VVADJ = VREF (Note 1)
17.551
17.817
_______________________________________________________________________________________
µA
µA
V
V
Simple Current-Limited Switch-Mode
Li+ Charger Controller
(Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VICHG/EN = VREF, VVADJ = VREF/2. MAX1873R: VBATT = VCSB = 8.4V;
MAX1873S: VBATT = VCSB = 12.6V; MAX1873T: VBATT = VCSB = 16.8V; TA = -40°C to +85°C. Typical values are at TA = +25°C,
unless otherwise noted.)
PARAMETER
CONDITIONS
MAX1873R
BATT Undervoltage Threshold
For ICHG/20 trickle
charge
MIN
MAX
4.8
5.2
UNITS
MAX1873S
7.2
7.8
MAX1873T
9.6
10.4
VICHG/EN = VREF
190
210
mV
VICHG/EN = VREF/4
40
60
mV
5
15
mV
6V < VCSSP < 28V
90
110
mV
Includes 50mV of hysteresis
500
700
mV
700
VREF
mV
V
CURRENT SENSE
CSB to BATT Battery Current-Sense
Voltage
CSB to BATT Current-Sense Voltage
when VBATT < 2.5V per Cell
CSSP to CSSN Current-Sense Voltage
CONTROL INPUTS/OUTPUTS
ICHG/EN Input Threshold
ICHG/EN Input Voltage Range for
Charge Current Adjustment
VADJ Input Current
VVADJ = VREF/2
-100
100
nA
ICHG/EN Input Current
VICHG/EN = VREF
-100
100
nA
0
VREF
V
VADJ Input Voltage Range
IOUT Voltage
Full scale
VCSB - VBATT = 200mV,
0 < IOUT < 500µA
3.6
4.4
25% scale
VCSB - VBATT = 50mV,
0 < IOUT < 500µA
0.9
1.1
Trickle charge
VCSB - VBATT = 10mV
75
325
No charge
current
VCSB - VBATT = 0,
IIOUT = sinking 20µA
40
90
V
mV
Note 1: While it may appear possible to set the Battery Regulation Voltage higher than the Battery Overvoltage Cutoff Threshold, this
cannot happen because both parameters are derived from the same reference and track each other.
Note 2: Specifications to -40°C are guaranteed by design, not production tested.
_______________________________________________________________________________________
5
MAX1873
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VICHG/EN = VREF, VVADJ = VREF/2. MAX1873R: VBATT = VCSB = 8.4V;
MAX1873S: VBATT = VCSB = 12.6V; MAX1873T: VBATT = VCSB = 16.8V; TA = +25°C, unless otherwise noted).
IOUT VOLTAGE
vs. CSB-BATT VOLTAGE
MAX1873T (4-CELL)
BATTERY VOLTAGE vs. CHARGING CURRENT
MAX1873 toc02
15.0
4.0
3.5
12.5
IOUT VOLTAGE (V)
BATTERY VOLTAGE (V)
4.5
MAX1873 toc01
17.5
10.0
7.5
3.0
2.5
2.0
1.5
5.0
1.0
2.5
0.5
RCSB + 0.068Ω
0
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
0
50
CHARGING CURRENT (A)
150
200
250
RECENT VOLTAGE VS. TEMPERATURE
4.205
REFERENCE VOLTAGE (V)
17.5
17.0
16.5
16.0
MAX1873 toc04
4.210
MAX1873 toc03
18.0
BATTERY REGULATION VOLTAGE (V)
100
CSB-BATT VOLTAGE (mV)
MAX1873T (4-CELL)
BATTERY REGULATION VOLTAGE
vs. VADJ VOLTAGE
4.200
4.195
4.190
4.185
MAX1873T
4.180
15.5
0
1
2
3
4
-50
5
0
25
50
75
TEMPERATURE (°C)
RECENT VOLTAGE
MAX1873R (2-CELL)
EFFICIENCY vs. INPUT VOLTAGE
4.205
90
EFFICIENCY (%)
4.200
4.195
4.190
100
MAX1873 toc06
100
MAX1873 toc05
4.210
80
70
60
4.185
VBATT = 7V
ICHG = 3A
MAX1873T
4.180
50
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
REFERENCE VOLTAGE (mA)
6
-25
VADJ VOLTAGE (V)
VS. REFERENCE CURRENT
REFERENCE VOLTAGE (V)
MAX1873
Simple Current-Limited Switch-Mode
Li+ Charger Controller
8
12
16
20
24
INPUT VOLTAGE (V)
_______________________________________________________________________________________
28
Simple Current-Limited Switch-Mode
Li+ Charger Controller
MAX1873T (4-CELL)
EFFICIENCY vs. INPUT VOLTAGE
MAX1873S (3-CELL)
EFFICIENCY vs. INPUT VOLTAGE
80
70
60
80
70
60
VBATT = 10.5V
ICHG = 3A
VBATT = 14V
ICHG + 3A
50
50
12
16
20
24
16
28
20
22
24
26
4-CELL BATTERY VOLTAGE AND
CHARGING CURRENT vs. TIME
CHARGING CURRENT
vs. SYSTEM LOAD CURRENT
3.0
2.5
2.5
12
2.0
10
1.5
CHARGING CURRENT
8
1.0
6
0.5
4
0
25
50
75
100
TIME (MINUTES)
125
150
CHARGING CURRENT (A)
3.0
CHARGING CURRENT (A)
MAX1873 toc09
BATTERY VOLTAGE
14
3.5
28
MAX1873 toc10
INPUT VOLTAGE (V)
16
0
18
INPUT VOLTAGE (V)
18
BATTERY VOLTAGE (V)
MAX1873 toc08
90
EFFICIENCY (%)
90
EFFICIENCY (%)
100
MAX1873 toc07
100
2.0
1.5
1.0
0.5
0
0
0.5
1.0
1.5
2.0
2.5
3.0
SYSTEM LOAD CURRENT (A)
_______________________________________________________________________________________
7
MAX1873
Typical Operating Characteristics (continued)
(Circuit of Figure 1, VDCIN = VCSSP = VCSSN = 18V, VICHG/EN = VREF, VVADJ = VREF/2. MAX1873R: VBATT = VCSB = 8.4V;
MAX1873S: VBATT = VCSB = 12.6V; MAX1873T: VBATT = VCSB = 16.8V; TA = +25°C, unless otherwise noted).
Simple Current-Limited Switch-Mode
Li+ Charger Controller
MAX1873
Pin Description
PIN
8
NAME
FUNCTION
1
CSSN
Source Current-Sense Negative Input. Connect a current-sense resistor between CSSP and CSSN to
limit total current drawn from the input source. To disable input current sensing, connect CSSN to CSSP.
2
CSSP
Source Current-Sense Positive Input. Also used for input source undervoltage sensing.
3
CCS
Input-Source-Current Regulation Loop Compensation Point
4
CCV
Battery Regulation Voltage Control-Loop Compensation Point. Pulling CCV high (to VL) through a 1.5kΩ
resistor disables the voltage control loop for charging NiCd or NiMH batteries.
5
CCI
Battery Charge Current Control-Loop Compensation Point
6
ICHG/EN
Battery Charging Current Adjust/Shutdown Input. This pin can be connected to a resistive-divider
between REF and GND to adjust the charge current sense threshold between CSB and BATT. When
ICHG/EN is connected to REF, the CSB-BATT threshold is 200mV. Pull ICHG/EN low (below 500mV) to
disable charging and reduce the supply current to 5µA.
7
IOUT
Charge Current Monitor Output. Analog Voltage Output that is proportional to charging current. VIOUT
= 20 (VCSB - VBATT) or 4V for a 200mV current-sense voltage (maximum load capacitance = 5nF).
8
VADJ
Battery Regulation Voltage Adjust. Set the battery regulation voltage from 3.979V per cell to 4.421V per
cell with 1% resistors. Output accuracy remains better than 0.75% even with 1% adjusting resistors
due to reduced adjustment range. For 4.2V, the voltage-divider resistors must be equal value
(nominally 100kΩ each).
9
REF
10
BATT
Battery Voltage-Sense Input and Battery Current-Sense Negative Input. Bypass to GND with a 68µF for
MAX1873R, 47µF for MAX1873S, and 33µF for MAX1873T. Use capacitors with ESR < 1Ω.
11
CSB
Battery Current-Sense Positive Input
12
GND
13
VH
14
EXT
15
DCIN
16
VL
4.2V Reference Voltage Output. Bypass to GND with a 1µF ceramic capacitor.
Ground
Internal VH Regulator. VH internally supplies power to the EXT driver. Connect a 0.22µF ceramic
capacitor between VH and DCIN.
Drive Output for External PFET. EXT swings from VDCIN to VDCIN - 5V.
Power-Supply Input. DCIN is the input supply for charger IC. Bypass to GND with a 0.22µF ceramic
capacitor.
Internal VL Regulator. VL powers the MAX1873’s control logic at 5.4V. Bypass to GND with a 2.2µF or
larger ceramic capacitor.
_______________________________________________________________________________________
Simple Current-Limited Switch-Mode
Li+ Charger Controller
MAX1873
D1
MBR5340
VIN 17V TO 28V
(9V MIN FOR 2- CELLS)
CVL
2.2µF
RP
4.7Ω
CVH
0.22µF
VH
CDCIN
0.22µF
VL
CSSP
CP
0.01µF
DCIN
RN
4.7Ω
RCSS
0.033Ω
SYSTEM
LOAD
CSSN
MAX1873
4V OUT PER
200mV ON RCSB
100kΩ
DISABLE
CCC
47nF
N
IOUT
EXT
L1
10µH
CSB
CCCS
47nF
BATT
REF
CREF
1µF
CCS
R1
VADJ
CCV
RCCV
10kΩ
GND
CL
47µF
P
ICHG/EN
CCI
CCCVS
0.1µF
D2
MBR5340
CN
0.01µF
RCSB
0.068Ω
CBATT
68µF
LI+
BATTERY
(2- TO 4-CELLS)
R2
CCCVP
1nF
Figure 1. Typical Application Circuit
Detailed Description
The MAX1873 includes all of the functions necessary to
charge 2-, 3-, or 4-series cell lithium-ion (Li+) battery
packs. It includes a high-efficiency step-down DC-DC
converter that controls charging voltage and current. It
also features input source current limiting so that an AC
adapter that supplies less than the total system current
in addition to charging current can be used without fear
of overload.
The DC-DC converter uses an external P-channel MOSFET switch, inductor, and diode to convert the input voltage to charging current or charging voltage. The typical
application circuit is shown in Figure 1. Charging current
is set by RCSB, while the battery voltage is measured at
BATT. The battery regulation voltage limit is nominally
set to 8.4V for the R version (2-cells), 12.6V for the S
version (3-cells), and 16.8V for the T version (4-cells),
but it can also be adjusted to other voltages for different Li+ chemistries.
Voltage Regulator
Li+ batteries require a high-accuracy voltage limit while
charging. The battery regulation voltage is nominally
set to 4.2V per cell and can be adjusted ±5.25% by
setting the voltage at VADJ between REF and ground.
By limiting the adjust range of the regulation voltage, an
overall voltage accuracy of better than ±0.75% is maintained while using 1% resistors.
An internal error amplifier maintains voltage regulation
to within ±0.75%. The amplifier is compensated at CCV
(see Figure 1). Individual compensation of the voltage
regulation and current regulation loops allows for optimal compensation of each. A typical CCV compensation network is shown in Figure 1 and will suffice for
most designs.
_______________________________________________________________________________________
9
MAX1873
Simple Current-Limited Switch-Mode
Li+ Charger Controller
5.4
REGULATOR
CSSN
UNDERVOLTAGE
COMPARATOR
BATT
SHUTDOWN
FOR ALL
BLOCKS
CSSP
VL
DCIN
VH
CCS
EXT
DRIVER
CONTROL
LOGIC
CCV
CCI
VH
VOLTAGE
ERROR AMP
GND
CSB
ICHG
/EN
CURRENT
ERROR AMP
BATT
IOUT
9R
R
REF
VADJ
A=1
R
4.2V
REFERENCE
portions of the system are powered up or put to sleep.
Without the benefit of input-current regulation, the input
source would have to be able to supply the maximum
system current plus the maximum charger-input current. The MAX1873 input-current loop ensures that the
system always gets adequate power by reducing
charging current as needed. By using the input-current
limiter, the size and cost of the AC adapter can be
reduced. See Setting the Input-Current Limit section for
design details.
Input current is measured through an external sense
resistor, RCSS, between CSSP and CSSN. The inputcurrent limit feature may be bypassed by connecting
CSSP to CSSN.
The input-current error amplifier is compensated at
CCS. A 47nF capacitor from CCS to GND provides suitable performance for most applications.
PWM Controller
The pulse-width modulation (PWM) controller drives the
external MOSFET at a constant 300kHz to regulate the
charging current and voltage while maintaining low
noise. The controller accepts inputs from the CCI, CCV,
and CCS error amplifiers. The lowest signal of these
three drives the PWM controller. An internal clamp limits
the noncontrolling signals to within 200mV of the controlling signal to prevent delay when switching between
the battery-voltage control, charging-current control,
and input-current regulation loops.
GND
Shutdown
Figure 2. Functional Block Diagram
Charging-Current Regulator
The charging-current regulator limits the battery charging current. Current is sensed by the current-sense
resistor (RCSB in Figure 1) connected between BATT
and CSB. The voltage on ICHG/EN can also adjust the
charging current. Full-scale charging current (ICHG =
0.2V / RCSB) is achieved by connecting ICHG/EN to
REF. See Setting the Charging-Current Limit section for
more details.
The charging-current error amplifier is compensated at
CCI (Figure 1). A 47nF capacitor from CCI to GND provides suitable performance for most applications.
Input-Current Regulator
The input-current regulator limits the source current by
reducing charging current when the input current
reaches the set input-current limit. In a typical portable
design, system load current will normally fluctuate as
10
The MAX1873 stops charging when ICHG/EN is pulled
low (below 0.5V) and shuts down when the voltage at
DCIN falls below the voltage at BATT. In shutdown, the
internal resistive voltage-divider is disconnected from
BATT to reduce the battery drain. When AC-adapter
power is removed, or when the part is shut down, the
MAX1873 typically draws 1.5µA from the battery.
Source Undervoltage Shutdown (Dropout)
The DCIN voltage is compared to the voltage at BATT.
When the voltage at DCIN drops below BATT + 50mV,
the charger turns off, preventing drain on the battery
when the input source is not present or is below the
battery voltage.
A diode is typically connected between the input
source and the charger input. This diode prevents the
battery from discharging through the body diode of the
high-side MOSFET should the input be shorted to GND.
It also protects the charger, battery, and systems from
reversed polarity adapters and negative input voltages.
______________________________________________________________________________________
Simple Current-Limited Switch-Mode
Li+ Charger Controller
Setting the Charging-Current Limit
The charging current ICHG is sensed by the currentsense resistor RCSB between CSB and BATT, and is
also adjusted by the voltage at ICHG/EN. If ICHG/EN is
connected to REF (the standard connection), the
charge current is given by:
VIOUT = 20( VCSB − VBATT ) or
VOUT = 20(RCSB × ICHG )
ICHG = 0.2V / RCSB
where VCSB and VBATT are the voltages at the CSB and
BATT pins, and ICHG is the charging current. IOUT can
drive a load capacitance of 5nF.
Design Procedure
Setting the Battery-Regulation Voltage
For Li+ batteries, VADJ sets the per-cell battery-regulation voltage limit. To set the VADJ voltage, use a resistive-divider from REF to GND (Figure 1). For a battery
voltage of 4.2V per cell, use resistors of equal value
(100kΩ each) in the VADJ voltage-divider. To set other
battery-regulation voltages, see the remainder of this
section.
The per-cell battery regulation voltage is a function of
Li+ battery chemistry and construction and is usually
clearly specified by the manufacturer. If this is not
clearly specified, be sure to consult the battery manufacturer to determine this voltage before charging any
Li+ battery. Once the per-cell voltage is determined,
the VADJ voltage is calculated by the equation:
[
]
VVADJ = 9.5( VBATTR ) / N − (9VREF )
where VBATTR is the desired battery-regulation voltage
(for the total series-cell stack), N is the number of Li+
battery cells, and VREF is the reference voltage (4.2V).
Set VVADJ by choosing R1. R1 should be selected so
that the total divider resistance (R1+ R2) is near 200kΩ.
R2 can then be calculated as follows:
[
]
R2 = VVADJ / ( VREF − VVADJ ) × R1
Since the full range of VADJ (from 0 to VREF) results in
a ±5.263% adjustment of the battery-regulation limit
(3.979V to 4.421V), the resistive-divider’s accuracy
need not be as tight as the output-voltage accuracy.
Using 1% resistors for the voltage-divider still provides
±0.75% battery-voltage-regulation accuracy.
In some cases, common values for RCSB may not allow
the desired charge-current value. It may also be desirable to reduce the 0.2V CSB-to-BATT sense threshold
to reduce power dissipation. In such cases, the
ICHG/EN input may be used to reduce the charge-current-sense threshold. In those cases the equation for
charge current becomes:
(
)
ICHG = 0.2V VICH / EN / VREF / RCSB
Setting the Input-Current Limit
The input-source current limit, IIN, is set by the inputcurrent sense resistor, R CSS , (Figure 1) connected
between CSSP and CSSN. The equation for the source
current is:
IIN = 0.1V / RCSS
This limit is typically set to the current rating of the input
power source or AC adapter to protect the input source
from overload. Short CSSP and CSSN to DCIN if the
input-source current-limit feature is not used.
Inductor Selection
The inductor value may be selected for more or less
ripple current. The greater the inductance, the lower
the ripple current. However, as the physical size is kept
the same, larger inductance value typically results in
higher inductor series resistance and lower inductor
saturation current. Typically, a good tradeoff is to
choose the inductor such that the ripple current is
approximately 30% to 50% of the DC average charging
current. The ratio of ripple current to DC charging current (LIR) can be used to calculate the inductor value:
{
[
L = VBATT VDCIN(MAX) − VBATT
]} /
[VDCIN(MAX) × fSW × ICHG × LIR]
where f SW is the switching frequency (nominally
300kHz) and ICHG is the charging current. The peak
inductor current is given by:
______________________________________________________________________________________
11
MAX1873
Charge-Current Monitor Output
IOUT is an analog voltage output that is proportional to
the actual charge current. With the aid of a microcontroller, the IOUT signal can facilitate gas-gauging, indicate percent of charge, or charge-time remaining. The
equation governing this output is:
MAX1873
Simple Current-Limited Switch-Mode
Li+ Charger Controller
IPEAK = ICHG (1+ LIR / 2)
For example, for a 4-cell charging current of 3A, a
VDCIN(MAX) of 24V, and an LIR of 0.5, L is calculated to
be 11.2µH with a peak current of 3.75A. Therefore a
10µH inductor would be satisfactory.
MOSFET Selection
The MAX1873 uses a P-channel power MOSFET
switch. The MOSFET must be selected to meet the efficiency or power dissipation requirements of the charging circuit as well as the maximum temperature of the
MOSFET. Characteristics that affect MOSFET power
dissipation are drain-source on-resistance (RDS(ON))
and gate charge. Generally these are inversely proportional.
To determine MOSFET power dissipation, the operating
duty cycle must first be calculated. When the charger is
operating at higher currents, the inductor current will be
continuous (the inductor current will not drop to 0). In
this case, the high-side MOSFET duty cycle (D) can be
approximated by the equation:
V
D ≈ BATT
VDCIN
And the catch-diode duty cycle (D') will be 1 - D or:
V
− VBATT
D'≈ DCIN
VDCIN
where VBATT is the battery-regulation voltage (typically
4.2V per cell) and VDCIN is the source-input voltage.
For MOSFETs, the worst-case power dissipation due to
on-resistance (PR) occurs at the maximum duty cycle,
where the operating conditions are minimum sourcevoltage and maximum battery voltage. P R can be
approximated by the equation:
PR =
VBATT(MAX)
VDCIN(MIN)
× RDS(ON) × ICHG2
Transition losses (P T ) can be approximated by the
equation:
V
×I
×f
× t TR
PT = DCIN CHG SW
3
where tTR is the MOSFET transition time and fSW is the
switching frequency. The total power dissipation of the
MOSFET is then:
12
PTOT = PR + PT
Diode Selection
A Schottky rectifier with a current rating of at least the
charge current limit must be connected from the MOSFET drain to GND. The voltage rating of the diode must
exceed the maximum expected input voltage.
Capacitor Selection
The input capacitor shunts the switching current from
the charger input and prevents that current from circulating through the source, typically an AC wall cube.
Thus the input capacitor must be able to handle the
input RMS current. At high charging currents, the converter will typically operate in continuous conduction. In
this case, the RMS current of the input capacitor can
be approximated with the equation:
ICIN ≈ ICHG D − D2
where ICIN is the input capacitor RMS current, D is the
PWM converter duty cycle (typically VBATT/VDCIN), and
ICHG is the battery-charging current.
The maximum RMS input current occurs at 50% duty
cycle, so the worst-case input-ripple current is 0.5 x
ICHG. If the input-to-output voltage ratio is such that the
PWM controller will never work at 50% duty cycle, then
the worst-case capacitor current will occur where the
duty cycle is nearest 50%.
The impedance of the input capacitor is critical to preventing AC currents from flowing back into the wall
cube. This requirement varies depending on the wall
cube’s impedance and the requirements of any conducted or radiated EMI specifications that must be met.
Low ESR aluminum electrolytic capacitors may be
used, however, tantalum or high-value ceramic capacitors generally provide better performance.
The output filter capacitor absorbs the inductor-ripple
current. The output-capacitor impedance must be significantly less than that of the battery to ensure that it
will absorb the ripple current. Both the capacitance and
the ESR rating of the capacitor are important for its
effectiveness as a filter and to ensure stability of the
PWM circuit. The minimum output capacitance for stability is:

VBATT 
VREF 1+

 VDCIN(MIN) 
COUT >
VBATT × fSW × RCSB
______________________________________________________________________________________
Simple Current-Limited Switch-Mode
Li+ Charger Controller
The maximum output capacitor ESR allowed for stability is:
R
×V
RESR < CSB BATT
VREF
where RESR is the output capacitor ESR.
tings do not interfere with charging. However, the battery undervoltage-protection features remain active so
charging current is reduced when VBATT is less than
the levels stated in the BATT Undervoltage Threshold
line in the Electrical Characteristics Table. 5- or 6-series
Ni cells may be charged with the R version device, 7to 9-cells with the S version, and 10-cells with the T version.
The MAX1873 contains no charge-termination algorithms for Ni cells; it acts only as a current source. A
separate microcontroller or Ni-cell charge controller
must instruct the MAX1873 to terminate charging.
Compensation Components
The three regulation loops: input current limit, charging
current limit, and charging voltage limit are compensated separately using the CCS, CCI, and CCV pins,
respectively.
Chip Information
PROCESS: BiCMOS
TRANSISTOR COUNT: 1397
The charge-current loop error-amplifier output is
brought out at CCI. Likewise, the source-current erroramplifier output is brought out at CCS. 47nF capacitors
to ground at CCI and CCS compensate the current
loops in most charger designs. Raising the value of
these capacitors reduces the bandwidth of these loops.
The voltage-regulating loop error-amplifier output is
brought out at CCV. Compensate this loop by connecting a capacitor in parallel with a series resistor-capacitor from CCV to GND. Recommended values are shown
in Figure 1.
Applications Information
VL, VH, and REF Bypassing
The MAX1873 uses two internal linear regulators to
power internal circuitry. The outputs of the linear regulators are at VL and VH. VL powers the internal control
circuitry while VH powers the MOSFET gate driver. VL
may also power a limited amount of external circuitry,
as long as its maximum current (3mA) is not exceeded.
A 2.2µF bypass capacitor is required from VL to GND
to ensure stability. A 0.22µF capacitor is required from
VH to DCIN. A 1µF bypass capacitor is required
between REF and GND to ensure that the internal 4.2V
reference is stable. In all cases, use low-ESR ceramic
capacitors.
Charging NiMH and NiCd Cells
The MAX1873 may be used in multichemistry chargers.
When charging NiMH or NiCd cells, pull CCV high (to
VL) with a 1.5 kΩ resistor. This disables the voltage
control loop so the Li+ battery-regulation voltage set-
Pin Configuration
TOP VIEW
CSSN 1
16 VL
CSSP 2
15 DCIN
CCS 3
CCV 4
14 EXT
MAX1873R/S/T
13 VH
CCI 5
12 GND
ICHG/EN 6
11 CSB
IOUT 7
10 BATT
VADJ 8
9
REF
16 QSOP
______________________________________________________________________________________
13
MAX1873
where COUT is the total output capacitance, VREF is the
reference voltage (4.2V), VBATT is the maximum battery
regulation voltage (typically 4.2V per cell), VDCIN (MIN)
is the minimum source-input voltage, and RCSB is the
current-sense resistor (68mΩ for 3A charging current)
from CSB to BATT.
Simple Current-Limited Switch-Mode
Li+ Charger Controller
QSOP.EPS
MAX1873
Package Information
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
14 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2001 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.